MIELE CS 1028 02 User Manual

Operating and Installation  
Instructions  
Gas Combiset  
CS 1028  
®
®
en - US, CA  
To prevent accidents and  
appliance damage,  
read these instructions  
before  
installation or use.  
M.-Nr. 07 369 720  
Contents  
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Guide to the combiset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Before using the combiset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Turning on and off / Regulating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Using the cooktop during a power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Ignition Safety Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Technical Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Installation dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Cut out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Installation of multiple appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Attach the spring clips and support bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Installing the appliance / appliances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Removing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Sealing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Tiled surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Gas pressure regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Nominal ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Converting to another type of gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Help protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
3
IMPORTANT SAFETY INSTRUCTIONS  
Children  
WARNING- When using your gas  
Children should not be left  
~
unattended in an area where the  
appliance follow basic  
precautions, including the  
following:  
appliance is in use. Never allow  
children to sit or stand on any part of  
the appliance.  
This gas combiset conforms to all  
uniform safety codes and  
regulations.  
Caution: Do not store items of interest  
to children in cabinets above the  
appliance. Children climbing on the  
appliance to reach these items could  
be injured.  
Read all instructions before  
installation or use to prevent  
injury and appliance damage.  
The appliance is hot during use and  
~
remains so for some time after being  
switched off. Keep children away from  
the appliance.  
Keep these operating instructions  
in a safe place and pass them on  
to any future user.  
Keep all pots and pans out of the  
~
reach of children. Danger of burning or  
SAVE THESE INSTRUCTIONS  
scalding.  
Ensure that any packing material, is  
~
Correct usage  
disposed of safely and kept out of the  
reach of children. Danger of  
suffocation!  
Only use the gas combiset for  
~
residential cooking, and for the  
purposes described in this manual.  
Other uses are not permitted and can  
be dangerous.  
Persons who lack physical, sensory  
~
or mental abilities, or experience with  
the appliance should not use it without  
supervision or instruction by a  
responsible person.  
4
IMPORTANT SAFETY INSTRUCTIONS  
Technical safety  
Install the appliance so that the  
~
power cord and gas piping do not  
Installation, repair and maintenance  
~
come into contact with any portion of  
the combiset which may become hot  
during use.  
work should be performed by a Miele  
authorized service technician. Work by  
unqualified persons could be  
dangerous and may void the warranty.  
Do not use an extension cord to  
~
connect this appliance to electricity.  
Extension cords do not guarantee the  
required safety of the appliance.  
Before installing the combiset,  
~
check for externally visible damage.  
Do not operate a damaged appliance.  
A damaged gas combiset is a hazard.  
Do not operate the appliance until it  
~
has been properly installed in the  
countertop.  
Before installation, make sure that  
~
the voltage and frequency listed on the  
rating label correspond with the  
household electrical supply. This data  
must correspond to prevent injury and  
appliance damage. Consult a qualified  
electrician if in doubt.  
Do not operate any appliance with a  
~
damaged cord or plug, or if the  
appliance has been damaged in any  
manner. Contact Miele’s Technical  
Service Department.  
Be certain your appliance is  
~
properly installed and grounded by a  
Defective components should be  
~
replaced by Miele original spare parts  
only. Only with these parts can the  
manufacturer guarantee the safety of  
the appliance.  
qualified technician.  
To guarantee the electrical safety of  
~
this appliance, continuity must exist  
between the appliance and an effective  
grounding system. It is imperative that  
this basic safety requirement be met. If  
there is any doubt, have the electrical  
system of the house checked by a  
qualified electrician.  
Under no circumstance open the  
~
outer casing of the appliance.  
While the appliance is under  
~
warranty repairs should only be  
performed by a Miele authorized  
service technician. Otherwise the  
warranty is void.  
5
IMPORTANT SAFETY INSTRUCTIONS  
Before servicing, turn off the gas  
Safety  
~
valve and disconnect the power supply  
by either removing the fuse, unplugging  
the unit or manually “tripping” the  
circuit breaker.  
The appliance is hot during use and  
~
remains so for some time after being  
switched off. Be careful not to touch the  
appliance if it may still be hot.  
This equipment has not been  
~
Protect your hands with oven mitts  
~
or potholders when using the  
designed for maritime use or for use in  
mobile installations such as aircraft or  
recreational vehicles. However, under  
certain circumstances it may be  
possible for installation in these  
applications. Please contact the  
nearest Miele Dealer or the Miele  
Technical Service Department with  
specific requirements.  
appliance. Use only dry, heat resistant  
potholders. Moist or damp potholders  
used on hot surfaces can result in  
steam burns. Do not let the potholder  
touch the hot heating elements. Do not  
use towels or other bulky items near the  
appliance.  
Be sure drafts do not blow  
~
After connecting the appliance test  
~
for leaks according to the installation  
flammable material toward the flames  
or push the flames so that they extend  
beyond the edges of the pan.  
instructions.  
If there is any doubt concerning  
~
installation contact Miele’s Technical  
Be aware of loose fitting or hanging  
~
garments when operating the combiset,  
Service Department.  
they may present a fire hazard.  
Do not heat unopened containers.  
~
Built-up pressure may cause the  
container to burst and result in injury.  
,WARNING - NEVER use this  
appliance as a space heater to heat  
or warm the room. Doing so may  
result in carbon monoxide poisoning  
and overheating.  
Install the combiset in a room that  
~
has sufficient ventilation.  
This appliance must not be  
~
operated outdoors.  
Make sure all components of the  
~
gas burner is assembled correctly  
before using the combiset.  
6
IMPORTANT SAFETY INSTRUCTIONS  
Do not use pans that extend past  
~
the burner grate. Using larger pans  
Always position pan handles and  
~
utensils inward so they do not extend  
over adjacent work areas, burner or the  
edge of the combiset.  
may cause the flames to spread out  
and damage the surrounding  
countertop or other countertop  
appliances.  
Do not store items on the appliance  
~
when not in use. Items could melt or  
catch fire from residual heat or if the  
appliance is turned on inadvertently.  
For safety and stability, do not use  
~
pans with a bottom diameter smaller  
than the burner grate.  
Never cover the appliance with a  
~
cloth. A fire may result.  
Only certain types of glass, ceramic  
~
or other glazed cookware are suitable  
for use on a combiset without breaking  
due to the sudden temperature change.  
Do not let cooking grease or other  
~
flammable materials accumulate on the  
appliance.  
Do not use containers made of  
~
plastic or aluminum. They may melt at  
Do not use a steam cleaner to clean  
~
the appliance. Steam could penetrate  
electrical components and cause a  
short circuit.  
high temperatures.  
The burner grates supplied with the  
~
appliance must always be used. Never  
Spills containing salt or sugar  
~
should be removed immediately.  
place a pan on the burner by itself.  
Do not use aluminum foil to line any  
~
part of the combiset.  
Do not leave the combiset  
~
unattended while in use. Boil-overs  
For proper lighting and performance cause smoking, and greasy spill-overs  
~
of the burner, keep the igniter clean  
may ignite.  
and dry.  
Do not use water on grease fires.  
~
Smother any fire or flame, or use a dry  
Do not heat empty pots or pans,  
~
they may be damaged.  
chemical or foam-type extinguisher.  
For safety reasons the flame should  
~
be adjusted to be the same size as the  
Do not flambé under an exhaust  
~
hood. Flames could be drawn up into  
bottom of the pan or smaller. Do not  
the hood by the suction or the grease  
use small pans with high flame settings filters may ignite.  
as the flames can climb the sides of the  
pan.  
If there is a drawer directly  
~
underneath the appliance without a  
Ensure that the burner is always  
~
covered with a pan.  
wooden base in between, ensure that  
no aerosols, combustible liquids or  
other easily flammable materials are  
kept in it. If cutlery inserts are to be  
placed in the drawer, they must be  
made of a heat-resistant material.  
Only use cooking utensils suitable  
~
for combiset use.  
7
IMPORTANT SAFETY INSTRUCTIONS  
Make certain that the power cords of  
~
small appliances do not come in  
contact with the appliance. The  
insulation of the cable could become  
damaged. Danger of electric shock!  
In the event of damage or defect,  
~
turn off the appliance immediately. Turn  
off the gas shut off valve and  
disconnect completely from the  
electrical supply. Contact the Miele  
Technical Service Department.  
Do not use the appliance until it has  
been repaired.  
Ensure power is not supplied to the  
appliance while repair work is carried  
out.  
Before discarding an old appliance,  
~
disconnect it from the gas and  
electrical supply, and cut off the power  
cord to prevent it from becoming a  
hazard.  
SAVE THESE INSTRUCTIONS  
AND REVIEW THEM  
PERIODICALLY  
8
Guide to the combiset  
aBurner grate  
bBurner  
cControl knob  
9
Guide to the combiset  
Burner  
dBurner cap  
eBurner head  
fCover plate  
gIgnitor  
hIgnition safety control  
(Thermocouple)  
iBurner base  
10  
Before using the combiset  
Cleaning the combiset  
Metal components have a protective  
coating which may give off a slight odor  
the first time your new appliance is  
heated.  
Before using for the first time clean the  
appliance as follows:  
^ Remove any protective foil.  
The harmless odor will dissipate after a  
short time and does not indicate a  
faulty connection or appliance defect.  
^ Wash the removable parts of the gas  
burner in a mild solution of warm  
water and liquid dish soap.  
^ Dry and reassemble the parts in the  
correct order (see "Cleaning and  
care").  
^ Wipe down the stainless steel  
combiset with a suitable cleaner and  
dry thoroughly.  
11  
Operation  
Turning on and off / Regulating Turning on  
The control knob is used to turn on the  
burner and to regulate the strength of  
the flame.  
ß The gas supply is turned off  
* Ignition setting  
& Highest flame  
/ Lowest flame  
^ To turn on the burner, press the  
control knob down and turn it  
counterclockwise to the ignition  
position a to turn on.  
The knob must only be turned left to  
turn the appliance on and right to  
turn it off.  
^ When the flame ignites, keep the  
control pressed in for 8-10 seconds,  
and then let go.  
If the knob is :  
-
turned on without pressing it  
down first,  
If the burner does not ignite or the  
flame goes out, turn the control knob to  
"ß ". Try again after a few seconds.  
-
-
turned clockwise to turn on, or  
turned counterclockwise to turn  
the combiset off,  
If the burner still will not ignite after the  
second attempt, turn the control knob  
to "ß " and see "Frequently asked  
questions".  
parts of the combiset might get  
damaged. The manufacturer cannot  
be held responsible for these  
damages.  
^ Adjust the knob to the desired  
setting.  
12  
Operation  
Adjusting the flame  
Using the cooktop during a  
power failure  
The burner can be variably adjusted  
between the lowest and highest flame  
by turning the control knob.  
If there is an interruption to the  
electrical supply, the gas can be  
ignited using a match.  
^ Press the control knob down and turn  
it counterclockwise to the ignition  
position.  
^ While holding down the knob, light  
Since the outer portion of the flame is  
much hotter than the center, the flame  
should be set so that its tips do not  
spread beyond the sides of the pan.  
Flame tips which extend beyond the  
sides of the pan are hazardous.  
the gas at the burner with a match.  
When the flame appears, keep the  
control knob pressed in for  
8 - 10 seconds to allow the Ignition  
Safety Control to reach operating  
temperature.  
Turning off  
^ Turn the control clockwise to "ß ".  
This stops the flow of gas and the flame  
goes out.  
13  
Pans  
Pan size  
Suitable pans  
– Set the combiset to a high flame  
Unlike pans used on an electric  
when using a large diameter pan and combiset, the bases do not need to be  
low flame when using a small  
diameter pan.  
even for good results.  
Thick pan bases will give more even  
results, as hot spots are reduced due to  
better heat distribution.  
Thin pan bases will conduct the heat  
faster but not as evenly as thick pan  
bases. Stir the food frequently to  
prevent burning.  
– Generally, wide / shallow pans will  
heat faster and cook more evenly  
than narrow / tall ones.  
You can use a wok without any  
additional rings, trivets, etc.  
– Using oversized pans may cause the  
flames to spread out and damage  
the surrounding countertop or other  
countertop appliances.  
– Do not use small pans with high  
flame settings, the flame can climb  
the sides of the pan.  
– Pots with a smaller diameter than the  
burner grates and pots that do not sit  
securely (without wobbling) are  
hazardous and should not be used.  
The burner grates supplied with the  
appliance must always be used.  
Never place a pan on the burner by  
itself.  
14  
Safety features  
Ignition Safety Control  
This gas combiset incorporates an  
Ignition Safety Control which stops the  
supply of gas if the flame goes out.  
^ To reignite the burner, turn the  
control knob clockwise to “ß ”, then  
turn on the burner as usual.  
This safety feature is not operated by  
electricity, it will be active even if the  
appliance is in use during a power  
failure.  
15  
Cleaning and care  
Combiset  
Never use a steam cleaner to clean  
this combiset. Pressurized steam  
could cause permanent damage to  
the surface and to components for  
which the manufacturer cannot  
accept responsibility.  
Let the appliance cool to a safe  
temperature before removing the  
grates.  
^ Clean the grates, combiset and  
knobs with a sponge and a mild  
solution of warm water and liquid  
dish soap. Do not wash parts in the  
dishwasher.  
Do not use any sharp or pointed  
objects which could damage the  
seal between the frame and the  
countertop.  
^ Soak baked or hardened spills.  
Dry the combiset and grates  
thoroughly after cleaning.  
Never use scouring agents, pads,  
abrasive cleaning agents, or strong  
cleaners, e.g. oven sprays, stain or  
rust removers, these could damage  
the surface of the appliance.  
The stainless steel surfaces can be  
cleaned using a non-abrasive stainless  
steel cleaner.  
To help prevent resoiling, a conditioner  
for stainless steel can also be used.  
Apply sparingly with even pressure.  
These cleaning products are available  
from Miele.  
Keep the ignitor in the burner dry. If  
it gets wet it will not spark.  
Dry your combiset thoroughly after  
cleaning it to prevent lime deposits.  
Do not use stainless steel cleaner on or  
around the printing, it may rub off. Use  
only a soft sponge with some dish  
liquid and warm water to clean this  
area.  
Spills containing salt or sugar should  
be cleaned immediately.  
16  
Cleaning and care  
Burner  
Reassembling the burner  
Do not clean any parts of the burner  
in a dishwasher.  
The burner can be dismantled and  
cleaned when cool.  
^ Remove the burner parts and wash  
them in a solution of warm water and  
liquid dish soap. Dry them  
thoroughly. Make sure that the flame  
holes are clean and completely dry.  
^ Wipe the burner base clean with a  
damp cloth and then dry.  
Gently wipe the ignitor and ignition  
safety control with a slightly damp  
cloth, and then wipe dry.  
Do not let the ignitor get wet. If it  
gets wet it will not spark.  
^ Place cover plate c over burner  
base d so that the ignitor and the  
ignition safety control extend through  
their respective holes in the cover  
plate. The cover plate must sit evenly  
over the burner base.  
^ After cleaning dry all surfaces with a  
clean cloth.  
Do not use a warped cover plate.  
^ Place the burner base in position  
above the cover plate making sure  
that pins e slot into their respective  
holes in the burner head b.  
^ Place burner cap a in position.  
Be careful not to mix up the parts.  
17  
Frequently asked questions  
,Repairs should only be carries out by an authorized technician in  
accordance with local and national safety regulations. Unauthorized repairs  
could cause injury or appliance damage. The manufacturer cannot be held  
responsible for unauthorized work.  
The burner does not ignite after several attempts.  
Possible fault  
Solution  
The burner is not assembled correctly.  
See "Cleaning and Care -  
Reassembling the burner".  
The gas supply is not turned on.  
The burner is dirty.  
Turn on the gas supply.  
See "Cleaning and care".  
See "Cleaning and care".  
The flame holes are wet or blocked.  
The flame does not stay lit.  
Possible fault  
Solution  
During the ignition process, the flame needs to touch the ignition safety control  
so that it heats up. If the flames does not touch, check that:  
– The burner is seated correctly.  
See "Cleaning and Care -  
Reassembling the burner".  
– There is no soiling on the ignition  
safety control.  
The igniter does not spark.  
Possible fault  
Solution  
The circuit breaker has tripped.  
Re-set the circuit breaker. Contact an  
electrician for assistance if in doubt.  
Food has deposited itself between the  
ignitor and the burner cap.  
See "Cleaning and care".  
Food has deposited on the ignition  
safety control.  
See "Cleaning and care".  
The flame appears different than usual.  
Possible fault  
Solution  
The burner is assembled incorrectly.  
Reassemble the burner as shown in  
"Cleaning and Care - Burner".  
18  
Technical Service  
In the event of a fault which you cannot  
easily fix yourself, please contact the  
Miele Technical Service Department at  
the address on the back of this booklet.  
When contacting Technical Service  
please quote the serial number and  
model of the appliance.  
Adhere rating label sticker supplied  
with the appliance below.  
19  
Technical Service  
MieleCare  
(USA only)  
MieleCare, our Extended Service  
Contract program; gives you the  
assurance of knowing that your  
appliance investment is covered by 5  
years of worry free ownership.  
MieleCare is the only Extended Service  
Contract in the industry that guarantees  
repairs by a Miele Authorized Service  
Provider using genuine Miele parts.  
Only genuine Miele parts installed by  
factory trained professionals can  
guarantee the safety, reliability and  
longevity of your Miele appliance.  
Please note that unless expressly  
approved in writing by the Miele  
Service department, Extended Service  
Contracts offered by other providers for  
Miele products will not be recognized  
by Miele. Our goal is to prevent  
unauthorized (and untrained) service  
personnel from working on your Miele  
products, possibly doing further  
damage to them, you and/or your  
home.  
To learn more about MieleCare  
Extended Service Contracts, please  
contact your appliance dealer or visit  
us online at:  
20  
Installation Instructions  
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE  
To prevent accidents  
and appliance damage  
read these instructions  
before  
installation or use.  
IMPORTANT SAFETY INSTRUCTIONS  
Installation  
Deep fat fryers must not be installed  
~
directly next to gas combisets. Gas  
The minimum distances given in  
these Installation instructions are to  
combustible surfaces, and must be  
observed to ensure safe operation.  
Failure to do so increases the risk of  
fire.  
flames can ignite splattering oil. A  
distance of at least 11 5/16"" (288 mm)  
should be maintained between these  
two appliances.  
Install the appliance so that the  
~
power cord or gas piping does not  
come into contact with any portion of  
the combiset which may become hot  
during use.  
The cabinetry and venting hood  
should be installed first to prevent  
damage to the combiset.  
This appliance must be installed  
with its own shut off valve and the  
included gas pressure regulator.  
Both the valve and the regulator  
must be easily accessible to the  
consumer after the appliance is  
installed.  
Gas appliances should only be  
~
installed in a well ventilated area.  
The countertop must be bonded  
~
with heat resistant (212°F/100°C)  
adhesive to prevent distortion or  
dissolving.  
This appliance has not been  
~
This appliance must be  
designed for maritime use or for use in  
mobile installations such as recreational  
vehicles or aircraft. However, under  
certain conditions it may be possible for  
installation in these applications. Please  
contact the Miele Technical Service  
Department with specific requirements.  
disconnected from the gas supply  
during any pressure testing of the  
system performed in excess of ½ psi  
(3.5 kPa). This appliance must be  
isolated at test pressures equal to or  
less than ½ psi (3.5 kPa).  
The combiset must not be installed  
Any pipe connections must be made  
using a thread sealant approved for  
gas connections. Failure to correctly  
install these items could lead to a  
gas leak and subsequent explosion.  
~
over a dishwasher, washer, dryer,  
refrigerator or freezer. Heat radiated by  
the combiset may damage the  
appliances.  
Keep this instruction book in a safe  
place for reference and pass it on to  
any future user.  
22  
IMPORTANT SAFETY INSTRUCTIONS  
Safety distances above the  
appliance  
The minimum safety distance given by  
the hood manufacturer must be  
maintained between the combiset and  
the hood above it. See the installation  
instructions of the hood for these safety  
measurements.  
If the hood manufacturers instructions  
are not available or if flammable objects  
are installed over the combiset (e.g.  
cabinets, utensil rail, etc.), a minimum  
safety distance of 30" (760 mm) must  
be maintained.  
If there is more than one appliance  
beneath a hood (e.g. wok burner  
and electric combiset), and they  
have different minimum safety  
distances always observe the  
greater distance.  
23  
IMPORTANT SAFETY INSTRUCTIONS  
Safety distances to the sides  
of the appliance  
The appliance should only be installed  
as shown in the illustrations, while  
maintaining the required safety  
distances shown. Do not install the  
appliance between two tall cabinets,  
this is a fire hazard.  
(50 mm)  
2 "  
A distance of at least 2" (50 mm) must  
be kept between the countertop cut-out  
recommended  
and the rear wall because of the high  
temperatures radiated.  
The minimum distance required from  
the countertop cut-out to the side wall  
a:  
2"  
(50mm)  
2" (50 mm)  
for CS 1112  
CS 1122  
CS 1212  
CS 1221  
CS 1223  
CS 1326  
CS 1411  
1
not recommended  
6" (150 mm)  
for CS 1312  
CS 1322  
CS 1421  
10" (250 mm)  
for CS 1011  
CS 1012  
CS 1028  
not allowed  
24  
Installation  
Safety distance from the wall covering  
If a wall covering is installed, a minimum safety distance must be maintained  
between the countertop cut-out and the covering, since high temperatures can  
damage these materials.  
If the covering is made of a combustible material (such as wood), the distance  
between the countertop cut-out and the wall covering must be a minimum of  
2" (50 mm).  
For coverings made of non-combustible materials (such as metal, marble, granite  
or ceramic tiles) the minimum safety distance e between the countertop cut-out  
and the wall covering must be 2" (50 mm) minus the thickness of the covering.  
For example: thickness of wall covering 9/16" (15 mm)  
2" (50 mm) - 9/16" (15 mm) = minimum safety distance 1 3/8" (35 mm).  
aWall frame  
bWall covering  
x = thickness of the wall covering  
cCountertop  
dCountertop cut-out  
eMinimum safety distance  
with flammable materials 2" (50 mm)  
with non-flammable materials 2" (50 mm) minus x  
25  
Installation  
Installation dimensions  
aSpring clips  
bAppliance front  
cInstallation height  
dPower supply box with connection cable, L = 78 3/4" (2000 mm)  
eGas fitting  
fRating label  
26  
Installation  
Cut out  
If during installation the seal around the  
frame does not sit flush with the  
countertop in the corners, the corner  
radius, maximum 3/16" (4 mm), can be  
carefully filed down to fit.  
^ Make the countertop cut-out for one  
or more appliances as applicable.  
Remember to maintain a minimum  
safety distance from the back wall,  
as well as from any tall unit or side  
wall to the right or left of the hob.  
See "IMPORTANT SAFETY  
INSTRUCTIONS".  
^ Seal the cut surfaces with a suitable  
heat-resistant sealant to avoid  
swelling caused by moisture.  
The materials used must be  
heat-resistant.  
27  
Installation  
Installation of multiple  
appliances  
When installing more than one combiset appliance, a support bar b must be  
installed between the appliances.  
Countertop cut-out  
two appliances  
Countertop cut-out  
three appliances  
For the installation of three appliances  
the width of the countertop cut-out D is  
the sum of A and B and C.  
For the installation of two appliances  
the width of the countertop cut-out D is  
the sum of A and C.  
A, B and C = appliance width  
11 5/16", 15" or 22 11/16"  
(288 mm, 380 mm or 576 mm)  
minus 5/16" (8 mm) to allow for the  
overhang  
If more than three appliances are  
being installed, you will need to add,  
A, B or C for each additional  
appliance.  
D = width of the countertop cut-out  
28  
Installation  
Sample calculations for a countertop cut-out for three appliances  
A
B
C
D
appliance width  
minus 5/16"  
(8 mm)  
appliance width  
appliance width  
minus 5/16"  
(8 mm)  
Countertop  
cut-out  
11" (280 mm)  
11" (280 mm)  
11 5/16" (288 mm)  
15" (380 mm)  
11" (280 mm)  
33 3/8" (848 mm)  
40 5/8" (1032 mm)  
14 5/8" (372 mm)  
11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm)  
14 5/8" (372 mm) 11 5/16" (288 mm)  
14 5/8" (372 mm) 15" (380 mm)  
11" (280 mm)  
37" (940 mm)  
14 5/8" (372 mm)  
44 1/4" (1124 mm)  
14 5/8" (372 mm) 22 11/16" (576 mm) 22 3/8' (568 mm) 59 11/16" (1516 mm)  
22 3/8" (568 mm) 11 5/16" (288 mm)  
11" (280 mm)  
14 5/8" (372 mm)  
22 3/8" (568 mm)  
44 3/4" (1136 mm)  
52" (1320 mm)  
22 3/8" (568 mm)  
22 3/8" (568 mm)  
15" (380 mm)  
-
44 3/4" (1136 mm)  
29  
Installation  
aSpring clips  
bSupport bars  
cSpace between support bar and countertop  
dSealing strip  
The illustration represents the attachment of spring clips a and support bars b  
for 3 appliances.  
An additional support bar is required for each additional appliance. The position  
for attachment of an additional support bar depends on the width of appliance B.  
30  
Installation  
Attach the spring clips and  
support bars  
Wood or solid surface countertops  
^ Place the supplied spring clips a  
and the support bars b at the  
marked positions as shown above,  
by laying them on the upper edge of  
the cut-out and then securing them  
with the 1/8" x 1" (3.5 x 25 mm) screws  
(supplied).  
31  
Installation  
Granite countertop  
The screws are not needed for  
granite countertops.  
3/16"  
1"-1  
mm)  
(25-30  
^ Coat the edges of the spring clips a,  
c
a
^ and the space e between the  
support bars b and the countertop  
with silicone (supplied).  
^ Position and attach the spring clips  
a and support bars b with strong,  
double-sided tape c.  
32  
Installation  
Installing the appliance /  
appliances  
^ Place the front edge of the next  
appliance into the cut-out.  
^ Connect the appliance / appliances  
to the main power supply (see  
"Electrical connection").  
^ Feed the power cord down through  
the cut-out.  
^ Place the front edge of the appliance  
^ Turn the appliance / appliances on  
into the cut-out.  
and check the function.  
^ With a hand on each side of the  
appliance press down evenly on the  
edges until it clicks into position.  
When doing so make sure that the  
appliance seal sits tightly on the  
countertop to ensure it is sealed  
correctly. This is important to ensure  
an effective seal. Do not permanently  
seal into the countertop.  
The appliance may be lifted out  
using a special tool.  
The appliance can also be pushed  
up and out from underneath.  
Note: push the rear out first.  
Removing the appliance  
When installing more than one  
appliance, a sealing strip must be  
inserted into the support bar.  
If the appliance is accessible from  
below, it can be pushed up and out of  
the cut-out. Push up from the back first.  
^ Push the installed appliance to the  
side until the slots in the support bar  
are visible.  
If the appliance is not accessible from  
below, grip the appliance with both  
hands at the back, pull forward, then lift  
it up and out.  
^ Insert the sealing strip d into the  
slots in the support bar b.  
33  
Installation  
Sealing  
Tiled surfaces  
The grouting a and shaded area under  
the appliance frame must be flat and  
even so that the frame will lie evenly  
and the sealing strip under the edge of  
the upper part of the appliance can  
provide an adequate seal against the  
countertop.  
The appliance must not be permanently  
sealed into the countertop when  
installed. The sealing strip under the  
edge of the appliance provides a  
sufficient seal for the countertop.  
If the appliance is sealed into  
position, the countertop or appliance  
could be damaged if it needs to be  
removed for maintenance or service.  
34  
Electrical connection  
This appliance must be grounded  
according to local or national codes.  
This appliance is equipped with a  
three-prong grounding plug to  
prevent shock hazards. It should be  
plugged directly into a properly  
grounded outlet. Do not cut or  
remove the grounding prong from  
the plug. If the plug does not fit the  
outlet, have the proper outlet  
All electrical work should be  
performed by a qualified electrician  
in accordance with local codes and  
with the:  
-
National Electrical Code  
ANSI / NFPA No. 70  
for the USA  
installed by a licensed electrician.  
or  
-
To guarantee the electrical safety of  
this appliance, continuity must exist  
between the appliance and an  
effective grounding system. It is  
imperative that this basic safety  
requirement be met. If there is any  
doubt, have the electrical system of  
the house checked by a qualified  
electrician.  
Canadian Electrical Code Part I  
for Canada  
(CSA Standard C 22.1).  
,WARNING  
Disconnect the appliance from the  
main power supply before  
installation or service. To reduce the  
risk of electric shock, make sure that  
the appliance is properly grounded  
after installation.  
Note to the installer  
Please leave these instructions with the  
consumer or the appliance.  
Power supply  
The automatic ignition requires that the  
combiset be connected to a 120 VAC,  
60 Hz power supply. The supply line  
should be protected by a 15 A fuse.  
Actual power consumption (during  
ignition only) is 25 W.  
This appliance is equipped with a  
78 3/4" (2000 mm) long power cord that  
is ready for connection to the  
appropriate outlet.  
Place the power outlet so that it is  
accessible after the appliance has  
been installed in the countertop.  
35  
Electrical connection  
Wiring Diagram  
36  
Gas connection  
Installation and service must be  
performed by a qualified installer,  
service agency or the gas supplier.  
The gas connection must be made  
in accordance with local codes or, in  
the absence of local codes, with  
In Massachusetts a licensed  
plumber/gas fitter is required.  
-
the National Fuel Gas Code,  
ANSI Z 223.1/NFPA 54  
for the USA  
This appliance must be installed  
with its own shut off valve and the  
included gas pressure regulator.  
Both the valve and the regulator  
must be easily accessible to the  
consumer to turn on or shut off the  
gas supply after the appliance is  
installed.  
or  
-
the current Can/CGA B 149.1  
and .2 Installation Codes for gas  
burning appliances for Canada.  
Make sure that the maximum gas  
supply pressure before the gas  
pressure regulator is never more than  
½ psi for both natural gas or LP gas.  
This appliance and its individual  
shut off valve must be disconnected  
from the gas supply during any  
pressure testing performed in  
excess of ½ psi (3.5 kPa), or  
isolated from the gas line by closing  
its individual manual shut off valve at  
test pressures equal to or less than  
½ psi (3.5 kPa).  
The minimum supply pressure to get  
the required gas input is  
4" w.c. for natural gas:  
10" w.c. for LP gas.  
Any pipe connections must be made  
using a thread sealant approved for  
gas connections. Failure to correctly  
install these items could lead to a  
gas leak and subsequent explosion.  
37  
Gas connection  
Gas pressure regulator  
For convenience, an AGA or CGA  
approved flexible stainless steel gas  
hose (accordion type) may be used  
between the gas connection and the  
regulator. This will allow the appliance  
to be lifted out of the countertop for  
cleaning or servicing. Make sure that  
any drawers, cabinet doors, etc., do not  
rub on this gas hose.  
A pressure regulator that is convertible  
from natural to LP gas (Propane) or vice  
versa is included with the appliance.  
The included regulator corresponds  
with the gas type of the combiset. Verify  
before installing.  
The adjusted pressure is:  
natural gas - 4" w.c.  
LP gas - 10" w.c.  
Do not use any regulator unless it  
has been supplied by Miele. Doing  
so may cause a gas leak.  
If there is any doubt concerning  
installation contact the Miele Technical  
Service Department.  
After connecting the appliance check  
all fittings for gas leaks e.g. with  
soapy water.  
When installed properly, the flame will  
be steady and quiet. It will also have a  
sharp, blue inner core that will vary in  
length proportional to the burner size.  
Flame adjustment will not be  
aCombiset  
b½" NPT  
necessary.  
cRegulator  
As shown in the above diagram, the  
included regulator must be used when  
connecting the Miele combiset to your  
gas supply. This item has been  
customized by Miele to meet all  
applicable safety requirements. Make  
sure the regulator is easily accessible  
for adjustment after the appliance has  
been installed.  
38  
Gas connection  
Nominal ratings  
Maximum output  
Gas type  
BTU/hr  
27,600  
22,200  
kW  
8.1  
6.5  
Natural Gas (NG)  
Liquid Gas  
(Propane) (LP)  
Minimum output  
Gas type  
BTU/hr  
5,700  
kW  
1.67  
1.67  
Natural Gas (NG)  
Liquid Gas  
5,700  
(Propane) (LP)  
39  
Converting to another type of gas  
The combiset should have been  
ordered for connection to either natural  
gas or LP gas (propane).  
If the combiset is not configured for the  
proper type of gas connection please  
contact your Miele Dealer.  
40  
Help protect our environment  
Disposal of packing materials  
Disposal of an old appliance  
The cardboard box and packing  
materials are biodegradable and  
recyclable. Please recycle.  
Old appliances contain materials that  
can be recycled. Please contact your  
local recycling authority about the  
possibility of recycling these materials.  
Ensure that any plastic wrappings,  
bags, etc. are disposed of safely and  
kept out of the reach of children.  
Danger of suffocation!  
Before discarding an old appliance  
disconnect it from the electrical supply  
and cut off the power cord to prevent it  
from becoming a hazard.  
41  
42  
43  
Alteration rights reserved / 2409  
M.-Nr. 07 369 720 / 02  
For the most updated manual see the Miele web site.  

White Rodgers 500 User Manual
Silva Battery Charger Solar I User Manual
Sanyo Spw K125xh User Manual
Samsung Aw18ecb User Manual
Rocketfish Rf Gwii031 User Manual
Philips Mcd716 User Manual
KENWOOD LZH 70W User Manual
GE A1050 User Manual
CRAFTSMAN 580.676650 User Manual
BLAUPUNKT CANNES RCM 127 User Manual