MCCULLOCH ROB S400 02 User Manual

QUICK GUIDE  
McCULLOCH Robotic Mower  
ROB S400/S500/S600  
QG_P01_MCC_1141738-26.indd  
1
2020-01-10 14:09:46  
2
1
3
3.To connect the boundary wire  
1. Open the connector and lay the boundary wire in the connector.  
2. Press the connector and the wire together by using a pair of pliers.  
3. Cut off the wire 1-2 cm / 0.4-0.8 in. after the connectors.  
4. Press the boundary wire connectors onto the contact pins marked L (left) and R (right)  
on the charging station.  
4
NOTE: The right-hand wire must be connected to the right-hand contact pin on the  
charging station, and the left-hand wire to the left-hand pin.  
4.To install and connect the guide wire  
Install a guide wire to lead the robotic lawn mower to remote parts of the lawn and  
to help it to find the charging station.  
1. Push the guide wire through the bottom of the charging station and fasten it into  
place using the snap locks.  
2. Fit the connector to the guide wire in the same way as for the boundary wire,  
according to the instructions above.  
1
3. Press the guide wire connector onto the contact pin marked GUIDE on the  
charging station.  
4. Pull the guide wire a minimum of 1 m / 3.3 ft. straight out from the front edge of  
the charging station.  
7
5. Lay the guide wire from the charging station to the point on the boundary wire  
(eyelet) where the connection is made using stakes supplied or bury the wire.  
NOTE: Do not lay the guide wire in sharp bends and it cannot cross the boundary  
wire that for instance is laid out for an island.  
6. Cut the boundary wire at the center of the eyelet that was made in step 2.3.  
7. Connect the guide wire to the boundary wire by inserting the boundary wires and  
guide wire in the coupler, and pressing the coupler together with a pair of pliers.  
NOTE: After the guide wire is installed, attach the charging station to the ground  
with the supplied screws and allen key.  
min 1 m / 3.3 ft  
4
NOTE: For optimal performance through narrow passages please ensure the gui-  
de wire is laid correctly through it. Please read the Operator‘s manual for further  
instructions.  
Power supply  
(the appearance of the power supply  
may differ depending on market)  
Low voltage cable  
Boundary wire and  
couplers  
Stakes/Pegs  
Connectors  
Measurement  
gauge  
QG_P01_MCC_1141738-26.indd  
3
2020-01-10 14:09:52  
5. To start and stop the robotic lawn mower  
When starting the robotic lawn mower for the first time a start-up sequence begins where you  
choose your language, country, date, time and personal PIN code. There is also a guide calib-  
ration, where the robotic lawn mower automatically follow the guide wire. Read the Operator’s  
manual for more information.  
2
To start the robotic lawn mower  
1. Open the hatch to the keypad.  
2. Push the ON/OFF button for 3 seconds. The display is lit up.  
3. Enter the PIN code by using the up/down arrow buttons, and push the OK button.  
To stop the robotic lawn mower  
1. Push the STOP button.  
6. To change the settings  
All settings for the robotic lawn mower are done via the menu functions.  
Please read the Operator’s manual and become familiar with the menus and settings.  
1. The Schedule function is used to adjust the mowing time to suit your work area. If the robotic lawn  
mower is allowed to mow too often, the grass may appear flattened. Use the scheduling wizard to  
set a suitable schedule. Push the Schedule button and select Wizard and enter the size of your  
work area. If you want to change the schedule settings for individual days use Schedule >  
Advanced.  
2. Use the STAR button to select operating mode, for example Secondary area, Power cut or Spot cut.  
3. Use the HOME button to select the park mode Home & Stay or Home & Wait.  
4. Use the START button to begin the operation of the lawn mower.  
3
4
1
2
Test run the robotic lawn mower through narrow passages  
Narrow passages in the garden can make it difficult for the mower to find the charging station. Use the Test  
function to test that the robotic lawn mower can travel through the narrow passage.  
1. Place the robotic lawn mower in the charging station.  
2. Select Test in the menu (Settings > Installation > Lawn coverage > More > Test ) and push OK.  
Then push the Start button and close the hatch.  
3. Check that the robotic lawn mower follows the guide wire through the passage.  
a. If the robotic lawn mower runs through the passage, the test is complete.  
b. If the robotic lawn mower does not get through the passage: Check that the guide wire has been laid  
according to the instructions in the Operator’s manual.  
3
1
Copyright © 2020 Husqvarna AB. All rights reserved.  
McCulloch App available for download on  
AppStore and Google Play.  
McCulloch and other product and feature marks are trademarks of the Husqvarna Group.  
1142140-26  
2020-01-13  
QG_P01_MCC_1141738-26.indd  
4
2020-01-10 14:09:53  

Xerox Workcentre Pro 423 User Manual
Tru Test 3 J User Manual
Symbol Technologies Ls 1000 User Manual
Samsung Sh18zp0a User Manual
DELL S2421HSX User Manual
CRAFTSMAN 987.889000 User Manual
CRAFTSMAN 917.270940 User Manual
CANON PRO 200 02 User Manual
ACER ASPIRE E1 771G User Manual
ACER ASPIRE 4715Z 02 User Manual