MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY .............................. 1
INSTALLATION REQUIREMENTS................................................... 2
Tools and Parts............................................................................... 2
Remove Cardboard Template........................................................ 2
Location Requirements................................................................... 2
Product Dimensions ...................................................................... 3
Electrical Requirements ................................................................. 3
INSTALLATION INSTRUCTIONS..................................................... 4
Remove Mounting Plate ................................................................. 4
Rotate Blower Motor ...................................................................... 4
Locate Wall Stud(s)......................................................................... 6
Mark Rear Wall................................................................................ 7
Drill Holes in Rear Wall ................................................................... 7
Attach Mounting Plate to Wall........................................................ 8
Prepare Upper Cabinet................................................................... 8
Install Damper Assembly................................................................ 9
Install the Microwave Oven ............................................................ 9
Complete Installation.................................................................... 10
VENTING DESIGN SPECIFICATIONS............................................ 11
ASSISTANCE ................................................................................... 12
Replacement Parts ....................................................................... 12
Accessories................................................................................... 12
MICROWAVE HOOD COMBINATION SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10724870A
Installation Dimensions
NOTE: The grounded 3 prong outlet must be inside the upper
cabinet. See “Electrical Requirements” section.
Electrical Requirements
A
B
WARNING
12" (30.5 cm) min.
14" (35.6 cm) max.
upper cabinet and
side cabinet depth
30"
(76.2 cm)
min.
Electrical Shock Hazard
30"
(76.2 cm)
typical*
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
66" (167.6 cm) min.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
■
A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■
A time-delay fuse or time-delay circuit breaker.
■
A separate circuit serving only this microwave oven.
A. 2" x 4" wall stud
B. Grounded 3 prong outlet
GROUNDING INSTRUCTIONS
■
For all cord connected appliances:
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Exact dimensions may vary depending on type of range/cooktop
below.
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
Product Dimensions
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
16¹⁄₄"
(41.3 cm)
17¹⁄₈"
(43.5 cm)
+/- ³⁄₁₆"
(0.5 cm)
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
SAVETHESE INSTRUCTIONS
*Overall depth of product will vary slightly depending on door
design.
3
INSTALLATION INSTRUCTIONS
3. Remove 2 screws attaching blower motor to back of
microwave oven.
Remove Mounting Plate
Depending on your model, the mounting plate may be in the foam
packaging, or it may be attached to the back of the microwave
oven.
NOTE: To avoid possible damage to the work surface, cover the
work surface.
1. Remove any remaining contents from the microwave oven
A
cavity.
A. Screws (in recessed holes)
2. If the mounting plate is attached to the back of the microwave
oven, remove it and set it aside.
4. Lift blower motor out of microwave oven.
3. Tape the microwave oven door closed so that door does not
swing open while the microwave oven is being handled.
A
NOTE: To avoid damage to the microwave oven, do not grip or
use the door or door handle while the microwave oven is being
handled.
Rotate Blower Motor
The microwave oven is set for recirculation installation. For wall or
roof venting, changes must be made to the venting system.
NOTE: Skip this section if you are using recirculation installation.
Keep the damper assembly in case the venting method is
changed, or the microwave oven is reinstalled in another location
where wall or roof venting may be used.
A. Blower motor
5. Rotate blower motor 180° so that exhaust ports face the back
of microwave oven, and lower blower motor back into the
microwave oven.
Wall Venting Installation Only
1. Remove screws attaching damper plate to top of microwave
oven exterior. Slide damper plate toward the front of the
microwave oven and lift up.
A
A
B
A. Exhaust port
A. Screws
B. Damper plate
2. Keep damper plate and screws together and set aside.
4
6. Using diagonal wire cutting pliers, gently snip out the
5. Rotate blower motor so that exhaust ports face the top of
microwave oven, and flat sides of blower motor face back of
microwave oven. Lower blower motor back into microwave
oven.
rectangular damper vent covers at the perforations.
A
A
B
A. Exhaust port
A. Diagonal wire cutting pliers
B. Damper vent covers
IMPORTANT: If blower motor is not positioned with flat sides
facing the back of the microwave oven (as shown), performance
will be poor.
6. Reattach blower motor to back of microwave oven with 2
screws removed in Step 3 of “Wall Venting Installation Only.”
Securely tighten screws.
7. Reattach blower motor to back of microwave oven with 2
screws removed in Step 3.
8. Reattach damper plate. Make sure damper plate tabs are
inserted into the slots in the top of the microwave oven.
NOTE: If blower motor is not correctly oriented, the 2 screws
removed in Step 3 cannot be reattached to the microwave oven.
B
A
7. Using diagonal wire cutting pliers, gently snip out the
rectangular vent covers on the damper plate removed in
Step 1, at the perforations.
C
D
A. Damper plate
B. Screws
C. Damper plate tabs
D. Slots
A
B
A. Diagonal wire cutting pliers
B. Rectangular vent covers
8. Reattach damper plate. Make sure damper plate tabs are
9. Secure damper plate with 2 screws removed in Step 1.
inserted into the slots in the top of the microwave oven.
Roof Venting Installation Only
B
A
1. Repeat Step 1 from “Wall Venting Installation Only.”
2. Repeat Step 2 from “Wall Venting Installation Only.”
3. Repeat Step 3 from “Wall Venting Installation Only.”
4. Repeat Step 4 from “Wall Venting Installation Only.”
C
D
A. Damper plate
B. Screws
C. Damper plate tabs
D. Slots
9. Secure damper plate with 2 screws removed in Step 1 of “Wall
Venting Installation Only.”
5
Locate Wall Stud(s)
NOTE: If no wall studs exist within the cabinet opening, do not
install the microwave oven.
1. Using a stud finder, locate the edges of the wall stud(s) within
the opening.
See illustrations in “Possible Wall Stud Configurations.”
2. Mark the center of each stud, and draw a plumb line down
each stud center. See illustrations in “Possible Wall Stud
Configurations.”
Possible Wall Stud Configurations
These depictions show examples of preferred installation configurations with the mounting plate.
No Wall Studs at End Holes
Figure 1
No Wall Studs at End Holes
Figure 2
B
C
C
D
C
D
B
A
A
A
E
A
E
E
F
E
F
NOTE: If wall stud is within 6" (15.2 cm) of the vertical
centerline (see “Mark Rear Wall” section), only recirculation or
roof venting installation can be done.
Wall Stud at One End Hole
Figure 3
Wall Studs at Both End Holes
Figure 4
D
B
B
A,D
A
E
A,D A,D
E
C
E
C
E
C
F
C
F
A. End holes (on mounting plate)
B. Cabinet opening vertical centerline
C. Wall stud centerlines
D. Holes for lag screws
E. Support tabs
F. Mounting plate center markers
6
6. Holding the mounting plate in place, find the wall stud
centerline(s) drawn in Step 2 of “Locate Wall Stud(s),” and
mark at least 1, preferably 2 hole(s) through the mounting
plate, closest to the wall stud centerline(s). See figures 1, 2
and/or 3 in “Possible Wall Stud Configurations” in “Locate
Wall Stud(s)” section. The blackened holes in the shaded
areas are ideal hole locations.
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
1. Using measuring tape, find and clearly mark the vertical
centerline of the opening.
7. Set the mounting plate aside.
Wall Venting Installation Only
A
Upper cabinet bottom
³⁄₈" (1 cm)
A. Centerline
4" (10.2 cm)
2. Align the center markers on the cardboard template (carton
top cap) to the centerline on the wall, making sure it is level,
and that the top of the cardboard template is butted up
against the bottom edge of the upper cabinet.
Centerline
NOTES:
6" (15.2 cm)
6" (15.2 cm)
■
If the front edge of the upper cabinet is lower than the back
edge, lower the cardboard template so that its top is level with
the front edge of the cabinet.
8. Mark the centerline 3/8" (1 cm) down from the bottom edge of
the upper cabinet.
■
If the cardboard template is damaged or unusable, measure
and mark the wall with the dimensions described in Step 4.
9. Using measuring tape, measure out 6" (15.2 cm) on both sides
of the centerline, and mark.
10. Measure down 4" (10.2 cm) from the mark made in Step 8,
and mark.
D
11. Using a straightedge, draw the 2 horizontal, level lines through
the marks made in steps 8 and 10.
A
C
12. Draw the 2 vertical, plumb lines down from the marks made in
Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.
This is the venting cutout area.
B
13. Cut a 3/4" (19 mm) hole in one corner of the cutout area.
14. Using a keyhole saw, cut out the venting cutout area.
A. Rear wall
B. Cardboard template
C. Top of cardboard template must
align with front edge of cabinet.
Drill Holes in Rear Wall
In addition to being installed on at least 1 wall stud, the mounting
plate must attach to the wall at both end holes. If the end holes
are not over wall studs, use two 3/16-24 x 2" round-head bolts
with toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw
and one 3/16-24 x 2" round-head bolt with toggle nut; or if both
end holes are over wall studs, use 2 lag screws. Following are 3
installation configurations.
D. Front edge of upper cabinet
3. Holding the cardboard template in place, mark both holes in
the lower corners, and draw a horizontal line across the
bottom edge of the cardboard template. These represent the
mounting plate’s end holes and bottom edge.
4. Remove the cardboard template and check the markings:
Installation for No Wall Studs at End Holes
(Figures 1 and 2)
Upper cabinet bottom
1. Drill 5/8" (16 mm) holes through the wall at both end holes
marked in Step 3 of “Mark Rear Wall.”
15³⁄₄"
(40.0 cm)
17¹⁄₄"
(43.8 cm)
Centerline
2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s)
marked in Step 6 of “Mark Rear Wall.” Refer to figures 1 and 2
in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)”
section.
14¹⁄₈"
(35.9 cm)
14¹⁄₈"
(35.9 cm)
Installation for Wall Stud at One End Hole (Figure 3)
Bottom of mounting plate
Mounting plate end hole
1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole
■
The bottom edge line must be 17¹⁄₄" (43.8 cm) from the
bottom of the upper cabinet, and must be level.
marked in Step 3 of “Mark Rear Wall.”
2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into
the wall stud at the other hole marked in Step 6 of “Mark Rear
Wall.” Refer to Figure 3 in “Possible Wall Stud Configurations”
in “Locate Wall Stud(s)” section.
■
The end holes must be 15³⁄₄" (40.0 cm) from the bottom
edge of the upper cabinet, and must be on a level line with
each other. They must each be 14¹⁄₈" (35.9 cm) from the
centerline.
3. Drill a 5/8" (16 mm) hole through the wall at the other end hole.
5. With the support tabs facing forward (see illustrations in
“Locate Wall Stud(s)” section), align the mounting plate center
markers to the centerline on the wall, making sure its bottom
edge is aligned to the horizontal line drawn in Step 3, and that
the end holes are properly marked. Make sure the mounting
plate is level.
Installation for Wall Studs at Both End Holes (Figure 4)
1. Drill 3/16" (5 mm) holes into the studs at the end holes marked
in Step 3 of “Mark Rear Wall.”
7
Wall Stud at One End Hole (Figure 3)
Attach Mounting Plate to Wall
NOTE: Secure the mounting plate to the wall at both end holes
drilled into the wall studs and/or drywall using either 3/16-24 x 2"
round-head bolts and toggle nuts or 1/4 x 2" lag screws.
1. With the support tabs of the mounting plate facing forward,
insert a 3/16-24 x 2" round-head bolt through the end hole
that fits over the 5/8" (16 mm) hole drilled in Step 3 of
“Installation for Wall Stud at One End Hole” in the “Drill Holes
in Rear Wall” section.
Refer to illustrations in “Possible Wall Stud Configurations” in
“Locate Wall Stud(s)” section.
2. Start a toggle nut on the bolt from the back of the mounting
plate. Leave enough space for the toggle nut to go through
the wall and to open.
No Wall Studs at End Holes (Figures 1 and 2)
NOTE: The mounting plate must be secured to the wall on at least
3. Position mounting plate on the wall.
1 wall stud as well as at both ends.
4. Push the bolt with toggle nut through the drywall, and finger
tighten the bolt to make sure toggle nut has opened against
drywall.
1. With the support tabs of the mounting plate facing forward,
insert 3/16-24 x 2" round-head bolts through both end holes
of mounting plate.
2. Start toggle nuts on bolts from the back of the mounting plate.
Leave enough space for the toggle nuts to go through the wall
and to open.
5. Insert a lag screw into the remaining end hole.
6. If installing on a second wall stud, insert a lag screw into the
other hole drilled in Step 2 of “Installation for Wall Stud at One
End Hole” in the “Drill Holes in Rear Wall” section.
B
7. Check alignment of mounting plate, making sure it is level.
8. Securely tighten the lag screw(s) and bolt.
A
Wall Studs at Both End Holes (Figure 4)
1. Position mounting plate on the wall.
C
2. Insert lag screws into both end holes.
3. Check alignment of mounting plate, making sure it is level.
4. Securely tighten the lag screws.
A. 3/16-24 x 2" round-head bolt
B. Mounting plate
C. Spring toggle nut
Prepare Upper Cabinet
1. Disconnect power to outlet.
2. Remove all contents from upper cabinet.
3. Place Upper Cabinet Template against the bottom of the
upper cabinet, and attach with tape or thumbtacks. Make sure
the template centerline aligns with the vertical centerline on
the rear wall.
3. Position mounting plate on the wall.
4. Push the 2 bolts with toggle nuts through the drywall, and
finger tighten the bolts to make sure toggle nuts have opened
against drywall.
The “Rear Wall” arrows must be against the rear wall so that
the holes cut into the upper cabinet align with the holes in the
top of the microwave oven.
C
A
NOTES:
■
If the upper cabinet has a frame around it, trim the template
edges so that it fits inside the frame, against the upper cabinet
bottom. The template has trim lines to use as guides.
B
D
■
If the wall behind the microwave oven (as installed) has a
partial wall covering (for example, tile backsplash), be sure the
“Rear Wall” arrows align to the thickest part of the rear wall
(for example, the thickness of the tiles rather than the drywall).
A. 3/16-24 x 2" round-head bolt
B. Mounting plate
C. Spring toggle nut
D. Drywall
4. Make sure the 10" (25.4 cm) dimension from the rear wall to
points “D” and “E” on the template is maintained.
5. Insert lag screw(s) into the hole(s) drilled into wall stud(s) in
Step 2 of “Installation for No Wall Studs at End Holes” in the
“Drill Holes in Rear Wall” section.
6. Check alignment of mounting plate, making sure it is level.
7. Securely tighten all lag screws and bolts.
U
p
p
er
-
c
a
bine
t
tem la e
p t
E
D
10"
(25.4 cm)
10"
(25.4 cm)
G
F
8
5. Cut the 1¹⁄₂" (3.8 cm) diameter hole at the circular shaded area
“G” on the template. This hole is for the power supply cord.
NOTE: If upper cabinet is metal, the supply cord bushing needs to
be installed around the supply cord hole, as shown.
Install the Microwave Oven
WARNING
Excessive Weight Hazard
B
Use two or more people to move and install
microwave oven.
A
Failure to do so can result in back or other injury.
A. Metal cabinet
B. Power supply cord bushing
IMPORTANT: The control side of the microwave oven is the heavy
side. Handle the microwave oven gently.
1. Place a washer on each 1/4-20 x 3" flat-head bolt and place
6. Drill 3/8" (10 mm) holes at points “D” and “E” on the template.
These are for two 1/4-20 x 3" bolts and washers used to
secure the microwave oven to the upper cabinet.
inside upper cabinet near the 3/8" (10 mm) holes.
2. Make sure the microwave oven door is closed and taped shut.
For Roof Venting Installation Only
7. Cut 3/4" (19 mm) hole at one corner of the shaded rectangular
area “F” on Upper Cabinet Template.
8. Using a keyhole saw, cut out the rectangular area.
Install Damper Assembly
(for wall venting only)
1. Check that damper blade moves freely, and opens fully.
2. Position the damper assembly on the back of the microwave
oven so that the damper blade hinge is at the top, and the
damper blade opens away from the microwave oven.
3. Using 2 or more people, lift microwave oven and hang it on
A
B C
D
support tabs at the bottom of mounting plate.
NOTE: To avoid damage to the microwave oven, do not grip or
use the door or door handle while the microwave oven is being
handled.
A
B
A. Back of microwave oven
B. Damper assembly
C. Damper blade
A. Mounting plate
B. Support tabs
D. Sheet metal screws
4. With front of microwave oven still tilted, thread power supply
cord through the power supply cord hole in the bottom of the
upper cabinet.
3. Secure damper assembly with 2 sheet metal screws.
5. Rotate microwave oven up toward upper cabinet.
NOTE: If venting through the wall, make sure the damper
assembly fits easily into the vent in the wall cutout.
6. Push microwave oven against mounting plate and hold in
place.
9
NOTE: If microwave oven does not need to be adjusted, skip
2. Connect vent to damper assembly.
steps 7-9.
A
B
7. If adjustment is required, rotate microwave oven downward.
Using 2 or more people, lift microwave oven off of mounting
plate, and set aside on a covered surface.
8. Loosen mounting plate screws. Adjust mounting plate and
retighten screws.
9. Repeat steps 3-6.
10. With the microwave oven centered, and with at least one
person holding it in place, insert bolts through upper cabinet
into microwave oven. Tighten bolts until there is no gap
between upper cabinet and microwave oven.
NOTES:
■
Some upper cabinets may require bolts longer or shorter than
3" (7.6 cm). Longer or shorter bolts are available at most
hardware stores.
■
Overtightening bolts may warp the top of the microwave oven.
To avoid warping, wood filler blocks (installer to provide)
may be added. The blocks must be the same thickness as
the space between the upper cabinet bottom and the
microwave oven.
A. Vent
B. Damper assembly (under vent)
Complete Installation
1. Install filters. Refer to the User Instructions for filter placement.
A
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
A. Bolts
For Roof Venting Installation Only
Do not use an extension cord.
1. Insert damper assembly through the cabinet cutout so that the
long tab of the damper assembly slides under the raised tabs
of the damper plate. Then secure with sheet metal screw.
NOTE: The screw cannot be installed if the damper assembly is
not positioned as shown.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. Plug microwave oven into grounded 3 prong outlet.
3. Reconnect power.
A
B
C
4. Check the operation of microwave oven by placing 1 cup
(250 mL) of water on the turntable, and programming a cook
time of 1 minute at 100% power. Test vent fan and exhaust by
operating the vent fan.
5. If the microwave oven does not operate:
■
Check that a household fuse has not blown, or that a
circuit breaker has not tripped. Replace the fuse or reset
the circuit breaker. If the problem continues, call an
electrician.
D
E
F
A. Raised tabs
■
■
Check that the power supply cord is plugged into a
grounded 3 prong outlet.
B. Damper assembly
C. Sheet metal screw
D. Upper cabinet cutout
E. Long tab
See the User Instructions for troubleshooting information.
Installation is now complete.
F. Damper plate
Save Installation Instructions for future use.
10
VENTING DESIGN SPECIFICATIONS
This section is intended for architectural designer and
Rectangular to Round Transition
NOTE: The minimum 3" (7.6 cm) clearance must exist between
the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.
builder/contractor reference only.
NOTES:
■
Vent materials needed for installation are not provided with
microwave hood combination.
■
■
We do not recommend using a flexible metal vent.
A
To avoid possible product damage, be sure to vent air outside,
unless using recirculation installation. Do not vent exhaust air
into concealed spaces, such as spaces within walls or
ceilings, attics, crawl spaces or garages.
B
D
C
For optimal venting installation, we recommend:
■
■
■
using roof or wall caps that have back draft dampers
E
using a rigid metal vent
F
3" (7.6 cm)
using the most direct route by minimizing the length of the
vent and number of elbows to provide efficient performance
■
■
■
using uniformly sized vents
A. Roof cap
using duct tape to seal all joints in the vent system
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3¹⁄₄" x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)
rectangular to round transition piece
using caulking compound to seal exterior wall or roof opening
around cap
■
not installing 2 elbows together, for optimal hood performance
If venting through the wall, be sure that there is proper clearance
within the wall for the damper to open fully.
F. Vent extension piece, at least 3" (7.6 cm) high
If venting through the roof, and rectangular to round transition is
used, be sure there is at least 3" (7.6 cm) of clearance between
the top of the microwave oven and the transition piece. See
“Rectangular to Round Transition” illustration.
Recommended Standard Fittings
The following length equivalents are for use when figuring vent
length. See the examples in “Recommended Vent Length.”
A
B
C
Roof venting
Roof cap
D
E
F
G
A. Rectangular to round transition piece: 3¹⁄₄" x 10" to 6" = 5 ft
(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3¹⁄₄" x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)
C. 90° elbow: 3¹ꢀ₄" x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)
D. 90° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3¹⁄₄" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)
F. 45° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
Wall venting
Wall cap
G. 90° flat elbow: 3¹⁄₄" x 10" = 10 ft (8.3 x 25.4 cm = 3 m)
11
Recommended Vent Length
A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent
should be used.
6" (15.2 cm) vent system = 73 ft (22.2 m) total
A
B
The total length of the vent system including straight vent,
elbow(s), transitions and wall or roof caps must not exceed the
equivalent of 140 ft (42.7 m) for either type of vent. See
“Recommended Standard Fittings” section for equivalent lengths.
6 ft (1.8 m)
For best performance, use no more than three 90° elbows.
To calculate the length of the system you need, add the equivalent
lengths of each vent piece used in the system. See the following
examples:
2 ft
(0.6 m)
3¹⁄₄" x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total
A
B
6 ft (1.8 m)
C
D
A. Two 90° elbows = 20 ft (6.1 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 1 rectangular to round transition piece = 5 ft (1.5 m)
D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
2 ft
(0.6 m)
If the existing vent is round, a rectangular to round transition piece
must be used. In addition, a rectangular 3" (7.6 cm) extension vent
between the damper assembly and rectangular to round transition
piece must be installed to keep the damper from sticking.
C
A. One 3¹⁄₄" x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
ASSISTANCE
Call your authorized dealer or service center. When you call, you
will need the microwave oven model number and serial number.
Both numbers can be found on the model and serial number
plate, which is located behind the microwave oven door on the
front frame of the microwave oven.
If you need additional assistance, call us at our toll free number or
visit our website listed in the User Guide.
Accessories
Filler Panel Kits are available from your dealer to use when
installing this microwave oven in a 36" (91.4 cm) or 42" (106.7 cm)
wide opening. The filler panels come in pairs. Each panel is 3"
(7.6 cm) wide.
Replacement Parts
If any of the installation hardware needs to be replaced, call us at
our toll free number listed in the User Guide.
Following is a list of available replacement parts. You will need
your model number located on the front facing of the microwave
oven opening, behind the door.
■
■
■
■
Damper Assembly
Mounting Plate
Upper Cabinet Template
A
Mounting Screw Kit (includes parts A-G in “Parts Supplied” in
the “Tools and Parts” section)
A. Filler panels
Filler Panel Kits: 8171336 White
8171337 Black
8171338 Biscuit
8171339 Stainless Steel
99403 Almond
See your authorized dealer or service center for details.
W10724870A
SP PN W10725313A
8/14
Printed in China
© 2014. All rights reserved.
|