Lexmark X 1100 User Manual

Contents  
iii  
Thank you for purchasing a Lexmark X1100 Series  
All-In-One!  
Congratulations on your purchase. The Lexmark™ X1100 Series  
All-In-One combines the functionality of an inkjet printer, a scanner, a  
copier, and a fax machine all into a single, multifunction device, making it  
one of the most exciting products on the market today.  
This guide tells you how to perform printing, copying, scanning, and faxing  
tasks. Also included are sections describing the All-In-One software and  
troubleshooting information.  
iv  
Learning about the All-In-One  
Setting up the All-In-One  
If you have not already done so, follow the steps on the Setup Sheet to  
complete the hardware and software installation. If problems occur during  
the setup process, see “Setup troubleshooting” on page 20.  
Understanding the parts of the All-In-One  
Paper guide  
Slide next to paper to  
ensure proper feeding.  
Paper support  
Lift to load paper into  
the All-In-One.  
Control panel  
Use the buttons to operate the  
All-In-One (see page 2 for details  
about each of the buttons).  
Scanner unit  
Top cover  
Paper exit tray  
Lift to access the print  
cartridges.  
Lift to place an item on  
the scanner glass.  
Extend to hold paper as  
it exits the All-In-One.  
1
                   
USB cable connector  
2
1
USB cable  
Power supply  
Silver, metal contacts are on the  
left side of the power supply.  
Using the control panel  
The All-In-One has a control panel that lets you scan and copy with the  
press of a button.  
Power button  
Press to turn the All-In-One  
on and off.  
Scan button  
Paper Feed button  
Press to start the scanning  
Press to feed paper  
process and open the  
through the All-In-One.  
All-In-One Center.  
Black Copy button  
Color Copy button  
Press to make a black and  
white copy.  
Press to make a color copy.  
Note: Both the computer and the All-In-One must be turned on  
to make copies.  
2
               
Understanding the software  
The All-In-One software consists of four main components:  
The Lexmark X1100 Series All-In-One Center (scanning, copying,  
and faxing)  
Print Properties (printing)  
The Lexmark X1100 Series Solution Center (troubleshooting,  
maintenance, and cartridge ordering information)  
The Lexmark Photo Editor (editing graphics)  
Using the Lexmark All-In-One Center  
Use the Lexmark X1100 Series All-In-One Center software to scan, copy,  
and fax documents. There are three ways to open the All-In-One Center:  
Click Start Programs Lexmark X1100 Series  
Lexmark All-In-One Center.  
Double-click the Lexmark X1100 Series All-In-One Center icon on  
the desktop.  
Press Scan on the control panel. For more information about using  
the control panel, see page 2.  
The All-In-One Main Page displays.  
All-In-One Center  
All-In-One Main Page  
Scan section  
Preview section  
Copy section  
Creative Tasks  
section  
3
         
The All-In-One Main Page  
The All-In-One Main Page consists of four main sections: Scan, Copy,  
Creative Tasks, and Preview.  
From this section:  
You can:  
Scan  
• Select a program to send the scanned image to.  
• Choose what type of image is being scanned.  
• Choose how the scan will be used.  
Note: Click See More Scan Settings to view all  
settings.  
Copy  
• Select the quantity and color of your copies.  
• Select a quality setting for your copies.  
• Adjust the size of the scanned area.  
• Lighten or darken your copies.  
• Enlarge or reduce your copies.  
Note: Click See More Copy Settings to view all  
settings.  
Creative Tasks  
Choose from a variety of creative ideas.  
• Enlarge or reduce an image.  
• Repeat an image several times on one page.  
• Print an image as a multi-page poster.  
• E-mail an image to a friend.  
• Fax using your computer’s modem.  
• Save an image on my computer.  
• Edit text found in a scanned document (OCR).  
• Modify an image with a photo editor.  
Preview section  
• Select a region of the preview image to scan.  
• View an image of what will be printed or copied.  
Note: For more information about the All-In-One Main Page,  
click the Help button located in the upper right corner of  
the screen.  
4
               
View Saved Images page  
Use the View Saved Images page to perform tasks with images that are  
saved on the computer. The View Saved Images page consists of three  
sections.  
From this section:  
Open with...  
You can:  
Select a program to send the saved image to.  
Print a Copy...  
• Choose the quantity and color of your copies.  
• Select a quality setting for your copies.  
• Lighten or darken your copies.  
• Enlarge or reduce your copies.  
Note: Click See More Copy Settings to view all  
settings.  
Creative Tasks  
Select from a variety of creative ideas. For help, see  
page 4.  
Note: For more information about this page, click the Help  
button located in the upper right corner of the screen.  
Maintain/Troubleshoot page  
The Maintain/Troubleshoot page provides you with direct links to the  
Lexmark Solution Center. Choose from these topics:  
Maintain or fix quality problems  
Troubleshoot All-In-One problems  
Device status and ink levels  
More printing ideas and how to’s  
Contact information  
Advanced (skin, voice, and communication options)  
View the software version and copyright information  
For more information about the Lexmark Solution Center, see page 8.  
Note: For more information about this page, click the Help  
button located in the upper right corner of the screen.  
5
       
Using Print Properties  
Print Properties is the software that controls the All-In-One printing  
function. You can change the settings in Print Properties based on the type  
of project you want to create. You can open Print Properties from almost  
any program:  
1 From the program File menu, click Print.  
2 In the Print dialog box, click the Properties, Preferences, Options,  
or Setup button (depending on the program).  
The Print Properties screen displays.  
Note: Some programs open Print Properties differently.  
Print Properties  
Quality Copies tab and I Want To menu  
Print Properties  
tabs  
I Want To menu  
Select one of the  
projects from the  
menu to help  
print photos,  
banners,  
envelopes,  
posters, and  
more.  
Use the Quality/  
Copies, Paper  
Setup, and Print  
Layout tabs to  
select the print  
settings.  
The I Want To menu  
The I Want To menu displays when you open Print Properties. It contains a  
variety of task wizards to help you select the correct print settings for your  
project. Close the menu for a full view of the Print Properties dialog box.  
6
                     
Print Properties tabs  
All of the print settings are on the three main tabs of the Print Properties  
software: Quality/Copies, Paper Setup, and Print Layout.  
From this tab:  
You can change these settings:  
Quality/Copies  
Quality/Speed — Select a Quality/Speed setting.  
Multiple Copies — Customize how the All-In-One prints  
several copies of a single print job: collated or normal.  
Print Color Images in Black and White — Select this to  
print color images in black and white.  
Paper Setup  
Print Layout  
Type — Select the type of paper you are using.  
Paper Size — Select the size of the paper you are using.  
Orientation — Select how you want the document  
oriented on the printed page: portrait or landscape.  
Layout — Select the layout you want to print.  
Duplexing — Select this when you want to print on both  
sides of the paper.  
Note: For additional information about these settings,  
right-click a setting on the screen, and then select the  
What’s This? item.  
Save Settings menu  
From the Save Settings menu, you can name and save the current Print  
Properties settings for future use. You can save up to five custom settings.  
Options menu  
Use the Options menu to make changes to the Quality Options, Layout  
Options, and Printing Status Options settings. For more information on  
these settings, open the tab dialog box from the menu, and then click the  
Help button on the dialog box.  
The Options menu also provides you with direct links to different parts of  
the Lexmark Solution Center (see page 8), as well as software version  
information.  
7
                   
Using the Lexmark Solution Center  
The Lexmark X1100 Series Solution Center is a valuable information  
resource. To open the Lexmark Solution Center, click Start Programs  
Lexmark X1100 Series Lexmark X1100 Series Solution Center.  
The Printer Status tab displays.  
Lexmark Solution Center  
Printer Status tab  
Printer Status  
Ink levels  
The Lexmark Solution Center consists of six tabs: Printer Status, How To,  
Troubleshooting, Maintenance, Contact Information, and Advanced.  
From this tab:  
You can:  
Printer Status (Main • View the status of the All-In-One. For example, while  
dialog box)  
How To  
printing, the status is Busy Printing.  
• View the ink levels of the print cartridges.  
Learn how to:  
• Scan, copy, fax, and print.  
• Find and change settings.  
• Use basic features.  
• Print projects such as banners and iron-on transfers.  
Troubleshooting  
Maintenance  
• Learn tips about the current status.  
• Solve All-In-One problems.  
• Install a new print cartridge.  
Note: Wait until scanning is complete before installing  
new cartridges.  
• View shopping options for new cartridges.  
• Print a test page.  
• Clean to fix horizontal streaks.  
• Align to fix blurry edges.  
Troubleshoot other ink problems.  
• Remove Japanese postcard residue.  
8
               
From this tab:  
You can:  
Contact Information • Learn how to contact Lexmark by phone, e-mail, or on  
the World Wide Web.  
Advanced  
• Change the appearance of the Printing Status window  
and turn printing voice notification on or off.  
• Obtain software version information.  
Note: For more information, click the Help button located in  
the lower right corner of the screen.  
Using the Lexmark Photo Editor  
Use the Lexmark Photo Editor software to edit graphics. To open the  
Lexmark Photo Editor, click Start Programs Lexmark X1100  
Series Lexmark Photo Editor.  
The Lexmark Photo Editor displays.  
Use the touch-up tools to edit your graphic.  
Move your pointer over the tool for a description.  
Lexmark Photo Editor  
Touch-up tools  
9
     
Using the All-In-One  
The following sections give you everything you need to know for basic  
printing, scanning, copying, and faxing.  
Printing  
The Print Properties I Want To menu (see page 6) provides you with  
printing wizards to help you complete tasks such as printing banners,  
photographs, or posters.  
1 Depending on what you want to print, load the appropriate type of  
paper into the All-In-One. Place the paper against the right side of  
the paper support with the print side facing you. Make sure you  
select the paper size for your document. For help, see page 12.  
Load up to:  
100 sheets of plain paper  
25 sheets of labels  
20 sheets of banner paper  
10 sheets of greeting card stock  
10 Hagaki cards  
25 iron-on transfers  
25 sheets of photo/glossy paper  
10 transparencies  
10 envelopes  
Note: Do not load envelopes with:  
• Holes, perforations, cutouts, or  
deep embossing.  
• Metal clasps, string ties, or  
metal folding bars.  
Note: Since transparencies and  
photos require more drying time, we  
recommend that you remove each  
transparency or photo as it exits and  
allow to dry to avoid ink smearing.  
• Exposed flap adhesive.  
10  
                         
2 Squeeze and slide the paper guide to the left edge of the paper.  
3 Make sure the All-In-One is turned on.  
4 Click File Print.  
5 In the Print dialog box, click the Properties, Preferences, Options,  
or Setup button (depending on the program).  
The Print Properties dialog box displays.  
6 If the printing task you want to perform is on the I Want To menu,  
click it, and then follow the instructions on the computer screen;  
otherwise, click Close at the bottom of the menu.  
7 From the Quality/Copies tab, select the quality, speed, and copy  
settings.  
To see details about a setting, right-click a setting on the screen,  
and then select the What’s This? item.  
Quality/Speed  
settings  
Copy  
settings  
11  
 
8 From the Paper Setup tab, select the paper type, paper size, and  
orientation.  
To see details about a setting, right-click a setting on the screen,  
and then select the What’s This? item.  
Paper size  
setting  
Paper type  
setting  
Orientation  
setting  
9 From the Print Layout tab, select the layout and duplexing settings  
for the type of document you are printing.  
To see details about a setting, right-click a setting on the screen,  
and then select the What’s This? item.  
Layout  
setting  
Duplexing  
setting  
10 Once you have applied all the settings you want in Print Properties,  
click OK at the bottom of the screen to return to the Print dialog box.  
11 Click Print to complete your task.  
12  
 
Scanning  
The following steps show you how to scan and save images.  
1 Open the top cover of the All-In-One.  
2 Place the item you want to scan face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 3).  
The All-In-One Main Page displays.  
5 Click the Preview Now button located in the upper right corner of  
the All-In-One Main Page.  
An image of the scanned item displays in the preview section.  
6 Click and drag to select a specific area of the preview image to  
scan.  
7 Click See More Scan Settings to review and change the scan  
settings.  
8 Select your scan settings.  
13  
       
From the Send scanned image to: drop-down menu, select a  
program to send the scanned image to, or click the Creative Tasks  
section to display a list of projects.  
Preview Now button  
Click to see a preview  
of the image.  
Scan Now button  
Click to scan the item  
on the scanner bed.  
Scan settings  
Adjust the settings for  
the scanned item.  
Preview section  
See a preview of the image, and select an area to be  
scanned.  
9 If you are sending the scanned image to a software program, click  
Scan Now to complete the scan. If you are using the Creative  
Tasks section, follow the instructions on the computer screen.  
For a list of the Creative Tasks available from the All-In-One Main  
Page, see page 4.  
Copying  
Note: You can make a quick color or black and white copy.  
Press Color Copy or Black Copy on the control panel.  
To make black and white, gray, or color copies:  
1 Open the top cover of the All-In-One.  
14  
   
2 Place the item you want to copy face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 3).  
The All-In-One Main Page displays.  
5 Click See More Copy Settings to review and change the copy  
settings.  
The All-In-One Copy section expands:  
Preview Now button  
Click to see a preview of the image.  
Copy Now button  
Click to copy your image.  
Copy settings  
Adjust the settings for the copy.  
Preview section  
See a preview of the image, and select an area to be copied.  
6 Select your copy settings.  
Note: You may want to reduce or enlarge the image.  
7 Click Copy Now.  
15  
Faxing  
The following steps lead you through sending a fax using the computer  
modem.  
1 Open the top cover.  
2 Place the item you want to fax face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 3).  
5 From the Creative Tasks section of the All-In-One Main Page, click  
Fax an image.  
6 Follow the instructions on the computer screen.  
16  
   
Maintenance  
Replacing the print cartridges  
The Lexmark X1100 Series has been designed to print using the following  
cartridges.  
Item:  
Part number:  
Standard yield black cartridge  
Standard yield color cartridge  
Moderate use black cartridge  
Moderate use color cartridge  
16  
26  
17  
27  
Note: You can print using only the color cartridge, or with both  
a color cartridge and a black cartridge.  
For information about ordering supplies, see page 8.  
Before you install new or replacement print cartridges, remove the used  
cartridges.  
1 Make sure the All-In-One is on.  
2 Lift the scanner unit until the scanner support keeps it open.  
The print cartridge carrier moves and stops at the loading position  
unless the All-In-One is busy.  
3 Squeeze the tabs on the cartridge lids, and then lift the lids.  
4 Remove the old cartridges. Store them in an air-tight container or  
dispose of them.  
5 If you are installing new cartridges, remove the stickers and  
transparent tape from the bottom of the cartridges.  
Warning: Do not touch the gold contact area on the cartridges.  
17  
     
6 Insert the new cartridge. Make sure the color print cartridge is  
secure in the left carrier and then snap the lid closed.  
If you are installing a black print cartridge, make sure that it is  
secure in the right carrier, and then snap the lid closed.  
7 Lift the scanner unit and push the scanner support back while  
lowering the scanner unit until it is completely closed.  
Lexmark’s All-In-One warranty does not cover repair of failures or damage  
caused by a refilled cartridge. We do not recommend use of refilled  
cartridges. Refilling cartridges can affect print quality and cause damage to  
the All-In-One. For best results, use Lexmark supplies.  
18  
Troubleshooting  
This section helps you solve problems you may have with the All-In-One.  
Additional troubleshooting information is available in the Lexmark Solution  
Center. For help accessing the Lexmark Solution Center, see page 8.  
Troubleshooting checklist  
Before you try to solve the problem, check the following:  
Is the power supply firmly attached to the All-In-One and an  
electrical outlet?  
Are both the computer and All-In-One on?  
Is the USB cable securely attached to the computer and the  
All-In-One?  
Did you remove the sticker and transparent tape from the print  
cartridge? For help, refer to the setup documentation.  
Is the color cartridge secure in the left carrier?  
Is the black print cartridge secure in the right carrier, if you  
installed both?  
Is the paper loaded correctly? Make sure you do not force the  
paper into the printer.  
Did you install the printer software correctly? For help, refer to the  
setup documentation.  
Is the Lexmark X1100 Series set as the default? To check, click  
Start Settings Printers. If not, you need to remove and then  
reinstall the software. For help, see page 26.  
19  
       
Alignment page does not print  
1 Make sure you remove the sticker and transparent tape from the  
print cartridges. For help installing print cartridges, refer to the  
setup documentation.  
2 Make sure the color cartridge is secure in the left carrier.  
Make sure the black print cartridge is secure in the right carrier if  
you installed both.  
3 Make sure you loaded the paper correctly and did not force the  
paper into the All-In-One.  
When I insert the All-In-One software CD, nothing  
happens  
From the Desktop, double-click the My Computer icon, and then  
double-click the CD-ROM drive icon.  
All-In-One is not communicating with the computer  
1 Disconnect and reconnect both ends of the USB cable. For help,  
refer to the setup documentation.  
2 Unplug the All-In-One from the electrical wall outlet, reconnect the  
power supply, and then press Power. For help, refer to the setup  
documentation.  
3 Restart the computer. If the problem continues, remove and then  
reinstall the software. For help, see page 26.  
Installation appears incomplete  
The software may not be installed properly. Try the following:  
1 Right-click the My computer icon.  
Windows XP users, click Start to access the My computer icon.  
2 Click Properties.  
21  
       
3 If you are using Windows 98 or Windows Me, click the Device  
Manager tab.  
If you are using Windows 2000 or Windows XP, select the  
Hardware tab, and then click Device Manager.  
4 Look for the Other Devices category. If there are any Lexmark  
devices shown here, highlight them and then press the Delete key.  
Note: The Other Devices category displays only when  
unknown devices are present. Do not delete any  
Lexmark items unless they are present under the Other  
Devices category.  
5 Insert the CD, and install the software again. Do not restart the  
computer. For help, refer to the setup documentation.  
Printing troubleshooting  
All-In-One prints slowly  
1 Close all programs not in use. The memory resources may be low.  
2 Make sure the Print Properties Quality/Speed setting is set on  
Normal or Quick Print. For help, see page 7.  
3 Try printing a smaller file. If the memory resources are too low, you  
may not be able to print larger files. Consider purchasing more  
memory.  
Note: Photographs typically have a larger file size. Try  
lowering the scanning resolution.  
Print is too dark or smudged  
1 Remove the paper as it exits. Let the ink dry before handling.  
2 Adjust the Quality/Speed setting in Print Properties or in the  
All-In-One Center. For help, see page 6 or page 4.  
22  
       
The Better or Best Quality/Speed setting may cause smearing if  
used with plain paper. Try using Normal.  
3 Open the Lexmark Solution Center. For help, see page 8.  
4 From the Maintenance tab, click Clean to fix horizontal streaks.  
Vertical lines are jagged or edges are not smooth  
1 Adjust the Quality/Speed setting in Print Properties. For help, see  
page 7. For best print quality, select Better or Best.  
2 Align the print cartridges. To align the print cartridges:  
a Open the Lexmark Solution Center. For help, see page 8.  
b From the Maintenance tab, click Align to fix blurry edges.  
White lines appear in graphics or solid black areas  
Clean the print cartridge nozzles. Going long periods without using the  
All-In-One can cause the print cartridge nozzles to become clogged. To  
clean the cartridge nozzles:  
1 Open the Lexmark Solution Center. For help, see page 8.  
2 From the Maintenance tab, click Clean to fix horizontal streaks.  
All-In-One has a paper jam  
1 Follow the instructions on the screen for clearing the paper jam.  
2 Make sure you are using paper designed for an inkjet printer. For a  
list of recommended papers, see page 10.  
3 Make sure you are correctly loading the paper. For help, see  
4 Make sure the paper guide is against the left edge of the paper. For  
help, see page 11.  
23  
     
Scanning, copying, and faxing troubleshooting  
Scanning was not successful  
The software may not be installed properly. Follow the instructions for  
Scanning or using a scanned image with a software  
program takes a long time or freezes the computer  
Lower the scanning resolution. Scanning resolution is much different than  
printing resolution and is generally set much lower. To change the scanning  
resolution:  
1 Open the Lexmark All-In-One Center. For help, see page 3.  
2 From the Scan section, click See More Scan Settings.  
3 Click Display Advanced Scan Settings.  
4 From the Scan tab of Advanced Scan Settings, enter a lower scan  
resolution.  
Edge of the copy does not print  
Make sure the original is properly oriented on the glass. For help,  
see page 13.  
Make sure the area you want to copy is not larger than the printable  
area of the page. Apply the Fit-to-page feature. To apply the  
Fit-to-page feature:  
1 Open the Lexmark All-In-One Center. For help, see page 3.  
2 From the Copy section, click See More Copy Settings.  
3 From the Reduce/Enlarge section, click the second button, and  
then select Fit to page from the corresponding drop-down  
menu.  
4 Copy your document again.  
24  
         
Copy button on the control panel does not work  
Make sure the computer is on. The computer must be on in order  
for the All-In-One to work.  
Make sure you properly installed the software. For help, refer to the  
setup documentation. The software must be installed for the copier  
to work.  
Fax function does not work  
Make sure the computer and the All-In-One are on.  
Make sure the computer is connected to a phone line. A phone  
connection is required for faxing to function.  
The memory may be full. Wait until the faxes in memory have been  
sent, and then send the current fax again.  
25  
   
Removing and reinstalling the software  
If the All-In-One software is not functioning properly or a communications  
error message displays when you try to use the All-In-One, you may need  
to remove and then reinstall the printer software.  
1 From the desktop, click Start Programs  
Lexmark X1100 Series Uninstall Lexmark X1100 Series.  
Note: If Uninstall is not an option on the menu, see “All-In-One  
2 Follow the instructions on the computer screen to remove the  
All-In-One software.  
3 Restart the computer before reinstalling the software.  
4 Insert the CD and follow the instructions on the computer screen to  
install the software. For help, refer to the setup documentation.  
Other help sources  
If the preceding solutions do not solve the problem with your All-In-One:  
Refer to the Lexmark Solution Center software for more  
troubleshooting information:  
1 Click Start Programs Lexmark X1100 Series  
Lexmark X1100 Series Solution Center.  
2 Click the Troubleshooting tab on the left side of the screen.  
Visit our Web site at http://support.lexmark.com/ for help.  
26  
     
a Class B computing device,  
use a properly shielded and  
grounded cable such as  
Lexmark part number 1329605  
for parallel attach or 12A2405  
for USB attach. Use of a  
substitute cable not properly  
shielded and grounded may  
result in a violation of FCC  
regulations.  
Japanese VCCI notice  
Electronic emission notices  
Federal Communications  
Commission (FCC) compliance  
information statement  
The Lexmark 3100 Series  
4476-K01 has been tested and  
found to comply with the limits for a  
Class B digital device, pursuant to  
Part 15 of the FCC Rules.  
Operation is subject to the following  
two conditions: (1) this device may  
notcause harmfulinterference, and  
(2) this device must accept any  
interference received, including  
interference that may cause  
undesired operation.  
Any questions regarding this  
compliance information statement  
should be directed to:  
Director of Lexmark Technology &  
Services  
Lexmark International, Inc.  
740 West New Circle Road  
Lexington, KY 40550  
(859) 232-3000  
ENERGY STAR  
The EPA ENERGY STAR Office  
Equipment program is a  
The FCC Class B limits are  
designed to provide reasonable  
protection against harmful  
partnership effort with office  
equipment manufacturers to  
promote the introduction of  
energy-efficient products and to  
reduce air pollution caused by  
power generation.  
interference in a residential  
installation. This equipment  
Industry Canada compliance  
statement  
generates, uses, and can radiate  
radio frequency energy and, if not  
installed and used in accordance  
with the instructions, may cause  
harmful interference to radio  
communications. However, there is  
no guarantee that interference will  
not occur in a particular installation.  
If this equipment does cause  
harmful interference to radio or  
television reception, which can be  
determined by turning the  
This Class B digital apparatus  
meets all requirements of the  
Canadian Interference-Causing  
Equipment Regulations.  
Companies participating in this  
program introduce products that  
power down when they are not  
being used. This feature will cut the  
energy used by up to 50 percent.  
Lexmarkisproud to be aparticipant  
in this program.  
Avis de conformité aux normes  
d’Industrie Canada  
Cet appareil numérique de la  
classe B respecte toutes les  
exigences du Règlement sur le  
matériel brouilleur du Canada.  
As an ENERGY STAR Partner,  
Lexmark International, Inc. has  
determined that this product meets  
the ENERGY STAR guidelines for  
energy efficiency.  
equipment off and on, the user is  
encouraged to try to correct the  
interference by one or more of the  
following measures:  
European Community (EC)  
directives conformity  
This product is in conformity with  
the protection requirements of EC  
Council directives 89/336/EEC and  
73/23/EEC on the approximation  
and harmonization of the laws of  
the Member States relating to  
electromagnetic compatibility and  
safety of electrical equipment  
designed for use within certain  
voltage limits.  
Reorient or relocate the  
receiving antenna.  
Increase the separation  
between the equipment and  
receiver.  
Connect the equipment into an  
outlet on a circuit different from  
that to which the receiver is  
connected.  
A declaration of conformity with the  
requirements of the directives has  
been signed by the Director of  
Manufacturing and Technical  
Support, Lexmark International,  
S.A., Boigny, France.  
Consult your point of purchase  
or service representative for  
additional suggestions.  
The manufacturer is not  
responsible for any radio or  
This product satisfies the Class B  
limits of EN 55022 and safety  
requirements of EN 60950.  
television interference caused by  
using other than recommended  
cables or by unauthorized changes  
or modifications to this equipment.  
Unauthorized changes or  
The United Kingdom  
Telecommunications Act 1984  
modifications could void the user's  
This apparatus is approved under  
authority to operate this equipment. the approval number NS/G/1234/J/  
100003 for the indirect connections  
Note:To assure compliance  
with FCC regulations on  
electromagneticinterferencefor  
to the public telecommunications  
systems in the United Kingdom.  
27  
 
28  
Index  
ink cartridges  
ink levels  
A
D
Lexmark All-In-One  
Center  
E
electrical emission  
All-In-One Main Page  
Creative Tasks section  
envelopes  
L
Lexmark All-In-One  
Lexmark Solution Center  
F
B
banner  
banners  
G
Contact Information  
black and white, printing  
see duplexing  
H
hardware setup  
I
C
I Want To  
M
changequalitysettings  
change speed settings  
print on both sides of  
cartridges  
Maintain/Troubleshoot  
O
P
paper  
see more printing  
29  
paper guide  
Q
V
View Saved Images page  
Print a Copy...section  
R
photos  
voice notification  
S
saved images  
posters  
Preview section  
Preview Now button  
placing an item on the  
settings, saving for future  
software  
sound, see voice  
notification  
print cartridges  
T
troubleshooting  
troubleshooting checklist  
Printing Status window  
changing appearance  
30  

Schneider Electric Duradrive Direct Coupled Actuators Ma4x 715x User Manual
Samsung Aw07f2nba User Manual
NEC P502H User Manual
Napa Essentials 85 510 User Manual
Makita Dc1804 Mj User Manual
LG 49VL5F User Manual
HP ELITEBOOK 820 G3 User Manual
HITACHI 50EX12KV User Manual
BLACK DECKER FIRESTORM FS240DC User Manual
3000 Gasoline Generator User Manual