Lexmark All In One Printer X560 User Manual

Jam message  
Area name  
Lexmark™ X560  
Clearing Jams Guide  
Jam at Scanner  
7
ADF tray  
Open ADF Cover R  
and Remove Paper  
Turn the Green Dial  
to Remove Paper  
Avoiding and clearing  
jams  
Clearing Tray 1 (MPT) jams  
If the paper did not feed from the multipurpose feeder  
correctly, Jam at Tray 1appears.  
1 Pull the jammed paper out of the multipurpose feeder tray,  
and then remove any remaining paper from the tray.  
Avoiding jams  
The following hints can help you avoid jams:  
Use only recommended paper or specialty media.  
For more information, see the Card Stock & Label Guide  
available on the Lexmark Web site at  
Do not load too much paper. Make sure the stack height does  
not exceed the indicated maximum height.  
Jam message  
Area name  
Do not load wrinkled, creased, damp, or curled paper.  
Flex, fan, and straighten paper before loading it.  
Do not use paper that has been cut or trimmed by hand.  
Do not mix paper sizes, weights, or types in the same stack.  
Store the paper in an appropriate environment.  
Do not remove trays while the printer is printing.  
Push all trays in firmly after loading paper.  
Jam at Exit  
Open Door A  
1
2
3
Fuser top  
Jam at Reg. Roll  
Open Door A  
Fuser bottom  
Jam at Duplexer  
Open Door A  
Optional duplex unit  
Make sure the guides in the trays are properly positioned, and  
are not pressing too tightly against the paper.  
Lift Belt Unit  
Jam at Tray 3  
Open Tray 3  
Open Door A  
4
5
6
Optional 550-sheet tray  
(Tray 3)  
Make sure all printer cables are attached correctly. For more  
information, see the setup documentation.  
2 Push the release button, and gently lower the front door.  
Jam at Tray 2  
Open Tray 2  
Open Door A  
Standard tray (Tray 2)  
CAUTION—HOT SURFACE: To reduce the risk of injury  
from a hot component, allow the surface to cool before  
touching it.  
Understanding jam messages  
and locations  
Open doors and covers, and remove trays to access jam locations.  
The illustration shows possible jam locations. To resolve any jam  
message, you must clear all paper from the paper path.  
Jam at Tray 1  
Check Tray 1  
Open Door A  
Multipurpose Feeder (Tray 1)  
1
5 Grasp the handle, and pull Tray 1 out. Remove the tray  
completely.  
6 Remove any jammed paper from inside the tray housing.  
Clearing Tray 2 jams  
If the paper did not feed from Tray 2 correctly, the jam is in the tray.  
Jam at Tray 2appears.  
1 Grasp the handle, and pull Tray 1 out. Remove the tray  
completely.  
7 Align the tray, and insert it.  
3
2 Remove the jam. The jam could be in the tray or behind the  
Jams behind the tray area—Locate the jam on the  
bottom surface of the tray housing. You may have to reach  
far under the printer to locate the jam, as shown in the  
following illustration. Pull the jam straight out.  
tray area.  
Jams in the tray—Locate the single piece of paper lying  
on top of the stack. Pull it straight out.  
3 Align the tray, and insert it.  
4 Push the release button, and gently lower the front door.  
CAUTION—HOT SURFACE: To reduce the risk of injury  
from a hot component, allow the surface to cool before  
touching it.  
4
Jams in the tray—Locate the single piece of paper lying  
on top of the stack. Pull it straight out.  
5 Remove any jammed paper from inside the printer.  
6 Close the front door.  
Clearing Tray 3 jams  
If the paper did not feed from Tray 3 correctly, the jam is in the tray.  
Jam at Tray 3appears.  
1 Grasp the handle, and pull Tray 3 out. Remove the tray  
completely.  
2 Remove the jam. The jam could be in the tray or behind the  
tray area.  
5
4 Push the release button, and gently lower the front door.  
Jams behind the tray area—Locate the jam on the  
bottom surface of the tray housing. You may have to reach  
far under the printer to locate the jam, as shown in the  
following illustration. Pull the jam straight out.  
5 Remove any jammed paper from inside the printer.  
CAUTION—HOT SURFACE: To reduce the risk of injury  
from a hot component, allow the surface to cool before  
touching it.  
3 Align the tray, and insert it.  
6
CAUTION—HOT SURFACE: To reduce the risk of injury  
from a hot component, allow the surface to cool before  
touching it.  
6 Close the front door.  
2 Lift the fuser pressure release levers to release tension on the  
paper.  
1 Push the release button, and gently lower the front door.  
Clearing jams in the fuser  
If the paper is jammed in the fuser area, Jam at Exitor Jam  
at Reg. Rollappears. A Jam at Reg. Rollmessage  
indicates the paper is jammed below the fuser. A Jam at  
Exitmessage indicates the paper is jammed above the fuser.  
7
3 Lift the fuser cover, and then remove the jammed paper.  
4 Close the fuser cover, and then lower the pressure release  
levers.  
5 Close the front door.  
8
2 Pull out the jammed paper from the duplex unit. If jammed  
paper cannot be found, go to the next step.  
3 Lift the transfer belt unit.  
Clearing jams in the duplex unit  
If the paper did not feed through the duplex unit correctly, the jam  
is in the duplex paper path. Jam at Duplexerappears.  
CAUTION—HOT SURFACE: To reduce the risk of injury  
from a hot component, allow the surface to cool before  
touching it.  
1 Push the release button, and gently lower the front door.  
4 Remove any jammed paper from the duplex paper feeder.  
9
5 Close the transfer belt unit.  
6 Close the front door.  
Clearing jams in the ADF  
If the paper is jammed in the ADF, Jam at Scannerappears.  
Remove all jammed paper, and make sure the paper feed tray is  
not overfull.  
1 Remove all paper from the paper feed tray, and then open the  
ADF cover.  
10  
2 If the jam is in the paper feed area, remove the jam by carefully  
pulling it up.  
3 If the jam is at the paper exit area, turn the dial to remove the  
jam.  
4 Close the ADF cover.  
5 Open the scanner cover and remove any jammed paper from  
the paper feed area.  
11  
6 Close the scanner cover.  
7 When all the jammed paper is removed, Return the  
Removed Original and Press Startappears. Place  
the original document in the ADF, and then press Start  
to  
continue with the scan job.  
12  

Whirlpool Acq052 User Manual
Texas Instruments Sluu083a User Manual
Philips Sc368 User Manual
Panasonic Rod End Bearing Hrt Cr User Manual
Panasonic Kx Ft37nz User Manual
MAYTAG MMV4206FZ0 User Manual
CRAFTSMAN 316.380900 User Manual
CRAFTSMAN 113.213780 User Manual
ACER CP3271U User Manual
ACER ASPIRE V7 581G User Manual