LG LT340HBU User Manual

INSTALLATION MANUAL  
LED TV*  
* LG LED TV applies LCD screen with LED backlights.  
Please read this manual carefully before operating your set and  
retain it for future reference.  
LT340CBU*  
LT340C0U*  
LT340HBU*  
LT340H0U*  
Copyright © 2018 LG Electronics Inc. All Rights Reserved.  
3
INSTALLATION MENU  
Introduction  
The abundant functions for Hotel TV linked with software installation can be projected on OSD as Public  
Display Settings.  
The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s  
easy installation and convenient operation for Hotelier and System Integrators.  
* Image shown may differ from your TV.  
1
Press the (Settings) button for more than 5 seconds using the user remote control, channel information  
will appear at top left on the screen.  
2
3
Enter a four digit password and press OK button. The TV is set with the initial password “1-1-0-5.  
Use the  
button to select the desired menu.  
4
PUBLIC DISPLAY SETTINGS  
* Image shown may differ from your TV.  
1
Select Public Display Settings. When Public Display Settings is set to On (Work), all functions of Public  
Display Settings apply.  
Public Display Settings (ATSC)  
Decide to work all functions of Public Display Settings or not by setting Public Display Settings as On  
(Work) or Off (Do Not Work)  
When Public Display Settings is set to On (Work), all functions of Public Display apply.  
When Public Display Settings is set to Off (Do Not Work), all functions of Public Display do not apply.  
When it is set to On, Key Lock of the User Menu is disabled and it can be set through Local Key Operation  
of the Public Display Settings.  
The TV triggered by the external device (ex: SIMPLINK, TV Link-Tuner, etc.) operates separately from the  
Public Display Settings.  
When it is set to On, User Menu General Reset to Initial Settings is disabled.  
5
Power On Status  
Decide to select working status of TV Set when turn on main power.  
You can set with PWR, STD, LST.  
PWR always make TV set On status when turn on main power .  
STD make Stand-by status when turn on main power.  
LST make TVSet work like previous power status. As same concept as Power Backup mode; If main power  
were turned off in Power On status, TVSet would work in On status. If main power were turned off in Stand-  
by status, TVSet would work in Stand-by status.  
Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)  
Decide to apply volume policy of Start Volume, Maximum Volume and Minimum Volume  
as On (Work) or Off (Do Not Work).  
Start Volume  
This entry sets the start volume level when is power on.  
The level is specified as a number between minimum volume to maximum value.  
(Min ≤ Start ≤ Max)  
The default setting is Off (disabled).  
When enabled, if the value is lower then the minimum specified in the minimum volume entry,  
the minimum volume entry must be used.  
When enabled, if the value is larger then the maximum specified in the maximum volume entry,  
the maximum volume value must be used.  
Access to a volume in Timer Power On of User Menu must be fixed to start volume when HTNG  
HotelMode (Enable) and Start Volume (Off, 0 ~ 100) were set simultaneously.  
Maximum Volume  
This entry sets the Maximum Volume level the set.  
The level is specified as a number between Minimum Volume to 100. (Min ≤ Max ≤ 100)  
If the command volume up to higher than maximum volume is received, that should be ignored.  
The default value is 100.  
Minimum Volume  
This entry sets the Minimum Volume level the set will produce.  
The level is specified as a number between 0 to Maximum Volume. (0 ≤ Min ≤ Max)  
If the command volume down to lower than minimum volume is received, that should be  
ignored.  
The default value is 0.  
6
Key Operation  
Manage key usability of Local(Front) Key and Remote Control. When selected to On, following IR Operation  
and Local Key Operation will be worked by below.  
IR Operation  
Decide whether work the LG remote control or not.  
Able to set Normal, Use PWR Only, Block All  
When IR Operation is set to Block All, all normal remote keys don’t work. Use PWR Only (Block  
except power) makes block all remote keys except power key.  
Although IR Operation value is Use PWR Only or Block All. It can work in service mode. (In-Start,  
In-Stop, Power-Only, ADJ, Hotel-Mode, Hotel-Mode-Ready, P-Check, S-check, In-Time, FMode-  
Init, FMode-Start, FMode-AV, FMode-F1)  
Menu key action to enter the installation menu and key action with special menu(In-Start / EZ-  
Adjust …) are still available.  
When IR Operation is set to Normal (Work), all remote keys are available.  
Local Key Operation  
Decide to operate Local/Front Key working behavior by setting Local Key Operation as Normal,  
Use PWR Only, Block All  
When Local Key Operation is set to Block All, all local keys don’t work. (If value is Use PWR Only,  
it blocks all local keys except power key.)  
When Local Key Operation is set to Normal, all local key are available.  
Exception)  
In case of power off condition with all key are blocked, Power On Status value turns to PWR, and  
disabled status to fix value for power on operation. (fool-proof routine)  
7
Limited Mode  
Configure TV function’s limitation. When selected to On, following sub-menus will be worked by below.  
Setup Menu  
Decide to enter Channels of user menu as On (Enter possible) or Off (Enter impossible).  
When Setup Menu is set to On  
- The Channels of user menu is disabled.  
When Setup Menu is set to Off  
- The Channels of user menu is enabled.  
Input Source Change  
Decide to change input source or not by setting Input Source Change as On (Change possible) or  
Off (Change impossible).  
When Input Source Change is set to Off (Change impossible)  
- Input key doesn’t work, and input source changing via TV D/A key, TV/RADIO key aren’t possible  
(ex. Press TV/RADIO Key in HDMI source to view TV channel)  
- User’s input (pressing Channel key, numeral key, List key, Flash back key in all Input source except  
TV source) doesn’t work.  
- Entering Channels of User Menu item in the main menu OSD except TV mode doesn’t accepted.  
Because entering Channels item of User Menu makes present mode as TV mode even though  
present mode is not TV. Change to TV mode isn’t allowed.  
- Entering Channels of User Menu except TV mode is impossible regardless of Channel Change or  
Channels itemsvalue of User Menu.  
- TV can be only turned on with the input source which is irrelevant from the programme related  
information set (volume, input) in Timer Power On of User Menu.  
- Auto AV and HDMI-CEC still work regardless of Input Source Change’s value.  
When Input Source Change is set to On (Change possible), changing input source is available.  
Channel Change  
Decide to change channel or not by setting Channel Change as On (Change Possible) or Off  
(Change Impossible) when present source is TV.  
When Channel Change is set to Off (Change Impossible)  
- Channel Key, Numeral Key, List Key, Flash back Key don’t work and entering channel Menu in the  
Main Menu OSD is impossible.  
- Channel item in Timer Power On of User menu will be fixed.  
- Entering Channels of User Menu is impossible regardless of Channels item of User Menu.  
When Channel Change is set to On (Change Possible), Channel Key, Numeric Key, List Key, Flash  
back Key does work and entering Channel Menu in the Main Menu OSD is possible.  
8
Menu Display  
Function to decide whether work with menu (including relevant menus too) of control key (On –  
Enter possible) or not (Off – Enter Impossible).  
Although select Off (Enter impossible), the action that press a Menu button for 5 seconds to  
enter installation menu is available.  
When select On (Enter possible), Menu works.  
OSD Display  
Decide to display OSD or not by setting OSD Display as On (Display) or Off (Do not Display).  
When OSD Display is set to Off (Do not Display), all OSD is not displayed except some exception.  
Although select Off (Do not Display), the action that press a menu button for 5 seconds to  
enter installation menu and entering service menu are available. (In-Start, Power-Only, Adjust,  
Installation Menu …)  
System Provider Mode  
System Provider Mode allows access to the menu system from the front panel or remote control  
but access is controlled as follows:  
When value is On, Accessible Items on the menu system, others are not permissible.  
- Input select screens  
- Sleep Timer  
- Aspect Ratio  
- Closed Caption  
- Safety / My Media / About This TV  
Q.menu, which is related to Channels of User Menu, is not accessible.  
If the channel map is empty, Auto-tuning guide dialog should be blocked by pressing List, Fav,  
CH+ (Page up), CH- (Page down) keys.  
Power Management  
The Power Management feature will turn off the television receiver if no input control command is received  
from either the Local or IR Key within a selected hours.  
Activity on either of these inputs shall restart the Power Management timer and check key time interval  
again.  
This entry can be set to a value which is corresponding to the desired hours (1 to 7).  
Default value is Off (disabled).  
TV should off and on after apply this setting.  
DTV Channel Update  
It is a mode to set whether to update DTV channel information automatically or not.  
When DTV Channel Update is set to Auto, the function to update TV’s channel map according to DTV  
channel’s stream information  
DTV Channel Update is set to Manual, the function to keep TV’s channel map even though DTV channel’s  
information is changed.  
9
Power On Default  
Set the input source or channel to display and. A/V settings when turn on power in AC Power On or Stand-by  
status.  
Input Source  
Set whether it is turned on by the set input source or by the last stored input source.  
It is turned on by the Last Memory Input if the Input Source is turned off.  
It is turned on by the Last Pr. If the Input Source is turned off and the last memory Input is the  
RF.  
The available Input Source values should be rotated.  
If both the Input Source and the Timer Power On of User Menu are set, the Input source takes  
the priority.  
When the Input Source is changed the TV (TV, DTV, CATV, CADTV), Channel menu (Tune Mode,  
Major, Minor) is available.  
Access to an input source item and a channel in Timer Power On of User Menu must be disabled  
when Power On Default is activated.  
Tune Mode  
Tune the selected start channel with Physical or Virtual method. Usually, digital channel uses  
virtual channel and analog channel uses physical channel.  
Major  
Select major part of start channel number if Input source value is TV. (in case of ATV, it means  
physical channel number.)  
Minor  
Select minor part of start channel number if Input source value is TV.  
A/V Setting  
If A/V Setting is changed from Off to On, parameters that are set before entering installation menu  
are applied whenever turn on power.  
Following Parameters are applied to basic.  
- Picture section - PSM mode, Picture Data (Contrast, Brightness, Color, Sharpness, Tint)  
- Sound section - SSM mode, Sound Data (Balance, Equalizer Data)  
- AVL (Auto Volume Level) and Language, Teletext language, ARC Data.  
Except these, other parameters are applied differently according to the TV-Set.  
Aspect Ratio  
The aspect ratio determines the default aspect ratio that the set returns to on power up.  
The modes are as follows:  
- Aspect ratio = “Disable (0)stays at previous state, same as consumer model.  
- Aspect ratio = “Original (1)”  
- Aspect ratio = “4:3 ratio (2)”  
- Aspect ratio = “16:9 ratio (3)”  
If enabled, upon power up the television resets the aspect ratio to the specified state regardless  
of how the user has previously changed the aspect ratio.  
10  
Aux Source Setting  
The Auxiliary (Input) Source Setting feature will enable or disable for each external input. When Aux  
Source Setting is set to On (Work), the RJP or HDMI-CEC / HTNG will not operate  
Available Input Source List  
Decide whether selected Input Source is set to On (Enable) or Off (Disable).  
User cannot disable the current input’s Aux Source Setting.  
Factory Reset  
Factory reset returns all the parameters to the default settings.  
1
2
Press Enter key to proceed factory reset. and confirmation message window will be shown.  
When select YES, all television settings except UTT value should write to the default settings.  
11  
Public Display Settings  
Item  
Enable  
Disable  
Initial  
Public Display Settings  
On  
Off  
Off  
Power On Status  
Volume  
LST, STD, PWR  
STD  
Off  
On  
Off  
Start Volume  
Off, Minimum Volume ~ Maximum Volume  
Minimum Volume ~ 100  
Off  
Maximum Volume  
Minimum Volume  
Key Operation  
IR Operation  
Local Key Operation  
Limited Mode  
Setup Menu  
100  
0
Off  
Normal  
Normal  
Off  
0 ~ Maximum Volume  
On  
Off  
Normal / Use PWR Only / Block All  
Normal / Use PWR Only / Block All  
On  
On  
On  
On  
Off  
Off  
Off  
Off  
On  
Input Source Change  
Channel Change  
Menu Display  
On  
On  
On  
Off  
On  
OSD Display  
System Provider Mode  
Power Management  
DTV Channel Update  
Power On Default  
Input Source  
On  
On  
Off  
Off  
On  
Off  
Off  
Auto  
Off  
Off, 1 Hour ~ 7 Hours  
Auto  
On  
Manual  
Off  
Off, TV, DTV, ...  
TV  
Tune Mode  
Physical  
Virtual  
Physical  
2
Major  
Subject to Ch. Type  
Minor  
1 ~ 999 (DTV, CADTV)  
0
A/V Setting  
On  
Off  
Off  
Aspect Ratio  
Disable / Original / 4:3 / 16:9  
Disable  
Off  
Aux Source Setting  
On  
On  
Off  
Aux Input (AV1 ~ MAX_  
INPUT)  
Off  
On  
Factory Reset  
Confirmation window (YES / NO)  
12  
TV MANAGER  
USB  
Ez Download  
Ez Download is a function that enables users to download the desired items all at once, such as EPK (software  
update file), TLL (See Send to USB descriptions for more information regarding file types), Logo Image, etc.  
Splash images and EPK files should be copied into the folder named LG_DTV on the USB.  
TLL files should be copied to the root folder of the USB.  
Insert Image files shoud be copied into the folder named LG_SIG on the USB.  
* Image shown may differ from your TV.  
1
2
3
4
5
Plug USB memory card into the USB port of the TV.  
Use the  
Use the  
button to select the TV Manager option and then press the OK button.  
button to select the USB and Ez Download and press the OK button.  
Select a list to download and press the OK button.  
Select the EPK option (software update) and then use the two dots and three dots buttons to download  
either SPI Boot or LG Boot Logo. If you checked the LG Boot Logo checkbox, then the Splash image, if  
selected, will be unchecked. Also, if you select the LG Boot Logo and proceed with the download, the  
existing Splash image will be deleted.  
6
7
When you are finished with your selections, use the button to select Apply and then press OK.  
Wait for the download to complete. When it is finished, your TV will be turned off.  
NOTE  
If the DZM file is still in the USB after the download is complete:  
An Ez Download pop-up window will appear and list the file types, such as TLL, Logo Image, Background  
Images, EPK or Micom with the previously downloaded lists checked automatically.  
If the global TLL and model TLL files exist in the same USB root directory, then only the global TLL will be  
shown. If the global TLL has been deleted, then the model TLL will be shown.  
The download files may vary by model.  
13  
USB Cloning  
An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the  
same Master TV Setup: Public Display Settings, Installation menu settings, User A/V settings and the Channel  
Map. This newer procedure significantly decreases the installation time that would be necessary if the  
standard RS-232C method were used instead.  
Introduction  
(1) Overview USB Cloning Procedure  
Commercial TVs have the capability to support cloning internal TV data and Channel information with  
an external clone device called USB Cloning, in order to copy TV data accurately and quickly. The clone  
internal functions use slightly different internal processes for the two types of commercial TVs. However,  
the UI of cloning feature remains the same in both. Regarding the demands over the current cloning  
feature for quicker cloning, better portability and etc, we would like to announce the cloning process via  
USB port, named as USB Cloning. USB cloning process is divided into 2 main processes. One is writing the  
previously saved TV data into the TV, and one another is reading of current TV data into USB memory card.  
To avoid any confusion due to the words, it is clearly specified as Receive from USB and Send to USB in the  
whole process.  
(2) Data To Be Cloned  
The data cloned are the same data cloned by previous USB Cloning. Details are explained in the following:  
- 1. TV data includes:  
A. Installer Menu settings  
B. Main menu settings (Audio, Picture etc)  
- 2. Analog / Digital Channel information includes:  
A. Channel numbers  
B. Channel label  
C. Channel attributes including channel type, skipping status and etc.  
(3) Input Source  
The user needs a USB memory card with FAT formatted to make successive cloning via USB port. A USB  
memory card size more than 128 MB and less than 4 GB is recommended.  
NOTE  
Currently, support the preceding USB file system for FAT file format only. Other file formats including NTFS  
is not currently supported. Microsoft Windows officially supports FAT for the USB memory card.  
14  
Receive From USB  
* Image shown may differ from your TV.  
1
2
3
Plug USB memory card into the USB port of the TV.  
Use the  
Use the  
button to select the TV Manager option and then press the OK button.  
button to select the USB and Receive from USB and press the OK button.  
* Below explains the naming rules for .TTL files. The supported model line will be in the name of the file  
but the screen size will be listed as “xx. This allows TVs having the same chassis model number to use the  
same ‘*.TTLfile without regard to the screen size. ex) The name of ‘*.TTLfile is ‘xxLT340C0UB00000.TLLfor  
xxLT340C0UB model.  
4
5
Use the  
button to select the desired *.TTL files name and press the OK button.  
The TV is changed to Standby mode after a successful download. If the download failed, the TV will  
maintain the current screen.  
15  
Send To USB  
* Image shown may differ from your TV.  
1
2
3
4
5
Plug USB memory card into the USB port of the TV.  
Use the  
Use the  
Use the  
button to select the TV Manager option and then press the OK button.  
button to select the USB and Send to USB and press the OK button.  
button to select the desired file name and press the OK button.  
The TV will be changed to the TV Manager main screen after a successful download.  
16  
Download Boot Logo  
Make a ‘LG_DTVfolder on the USB flash drive and then copy the splash image file to that folder.  
* Image shown may differ from your TV.  
1
Connect the USB device to the USB IN jack on the TV.  
2
3
4
Use the  
Use the  
Use the  
button to select the TV Manager option and then press the OK button.  
button to select the USB and Download Boot Logo and press the OK button.  
button to select the desired file name and press the OK button.  
NOTE  
Splash Image update function supports only JPEG format file of less than 1 MB file size.  
Except for JPEG images with progressive encoding.  
We recommend you that splash image resolution match the TV`s panel resolution.  
Max resolution of splash image : Full HD 1920 x 1080, HD 1360 x 768.  
Min resolution of splash image : Full HD 64 x 64, HD 64 x 64.  
TV keep splash image until you change a new splash image.  
Please do not use the ampersand character(&) and the left angle bracket (<) in the file name to use DZM file  
on EZ Download.  
Non-standard photo/image file may not be displayed.  
17  
Diagnostics  
Diagnostics Setup  
Introduction  
This diagnostic function provides current status information of the TV in XML file format using a USB device. If  
the user sets a signal standard level, Signal Tracer Set checks the signal strength status of the digital channel  
that the user tuned to. It checks and records good and bad channel signals, and then provides the signal  
information to a USB storage device in XML file format.  
(1) Overview Diagnostics  
It provides status information of the TV and information about the current input in XML file format. (There  
are two kinds of information. There is information which is extracted regardless of the model, such as the  
model name or boot version, and there is information which is available depending on the model, such as  
the micom version, PTC version, etc.). The information created in the XML file can be checked in the TV’s UI  
by pressing 88888888 in the TV’s General menu.  
If a SignalTrace standard level is set, it saves the average value of the channel signal with less than 30  
tuning counts to the digital broadcasting channel. If the count is more than 30, it saves good and bad  
signals by comparing the average signal value to the current signal strength and signalTrace standard level  
(Signal Tracer Set) value.  
- Bad signal: BML (average value) > strength (current signal strength) and (BML - strength) > Signal Tracer  
Set  
- Good signal: BML< strength and (strength - BML) > Signal Tracer Set  
It provides the good and bad signals, average signal value, channel information, and date information etc.  
in USB in XML file format. (Saved in changedSignal_report tag) Up to 127 reports for good and bad signals  
are saved. If the reports number more than 127, they are written again beginning from 1.  
18  
(2) Saving some status information of the TV set through USB in XML file format  
Create an LG_SVC folder on the USB on a PC.  
Create an empty file named tv_signal.rms in the LG_SVC folder.  
Insert the USB device into the TV.  
If the “Diagnostics is completedmessage is displayed, remove the USB, open the tv_signal.rms file on a PC  
and check the XML (model name, FirmwareVersion, bootVersion etc.) created within the file.  
The information created in the XML file can be checked in the TV’s UI by pressing 88888888 in the TV’s  
General menu  
(3) Saving signal status information of digital channels through SignalTrace in XML format  
Go to TV Manager Diagnostics Diagnostics Setup  
Set the level value in Signal Tracer Set. (Disable, 10 to 90)  
Change the channel and tune to a digital channel, then maintain the status for more than 5 seconds.  
Create an empty file named tv_signal.rms in the LG_SVC folder.  
Insert the USB device into the TV.  
If the “Diagnostics is completedmessage is displayed, remove the USB, open the tv_signal.rms file on a PC  
and check XML created in the file.  
* If the user tunes to the same digital channel 30 times, the signal average is calculated. If the tuning count  
to the same digital channel is more than 30, the good/bad signals, current signal, average signal, date and  
channel information are saved in changedSignal_report XML tag.  
* The information created in SignalTrace is not displayed in the TV’s UI.  
* In USB cloning, the configured Signal Tracer value is not cloned.  
* When a factory reset is performed, Signal Tracer Set is disabled and traced information is deleted.  
19  
GENERAL  
Password Change  
* Image shown may differ from your TV.  
- To ensure more security, Password can be changed by installersown design.  
1
2
3
Go to General Password Change.  
Enter four digit password.  
Input the password again for confirmation.  
Set ID Setup  
1
Go to General Set ID Setup.  
Set ID Lock  
- Set the Set ID item in General Menu whether to activate or not.  
- Set to On (Work) or Off (Do Not Work).  
Set ID  
- Set the Set ID of TV Set with 1~99.  
20  
Configuration Setup  
* Image shown may differ from your TV.  
(1) Number of RCU  
It is a function to set whether to use Select RCU or not and set number of RCU.  
When Number of RCU is set to 0, this function do not use.  
Number of RCU value range 1~9  
* RCU(Remote Control Unit) : It is special RCU that operates only setted number of RCU in TV.  
(2) Splash Offset Time  
Set the splash image display time  
When Splash Offset Time is set to Off, TV logo(splash image) do not display.  
The time can be set to between 0 and 10 seconds.  
21  
(3) USB Auto Playback  
When USB Auto Playback is set to Movie, TV finds and plays the USB’s movie files located at the root(top)  
directory Movies if USB is plugged in. (Some menu OSDs may prevent this function.)  
When USB Auto Playback is set to Photo, TV finds and plays the USB’s photo files located at the root(top)  
directory Photos if USB is plugged in. (Some menu OSDs may prevent this function.)  
If it reaches the last file, it starts the first file again.  
(4) 15Min Auto Off  
When 15Min Auto Off is set to Enable, TV will turn off if there is no signal in 15Min.  
(5) Auto Sensing  
The input is automatically switched when the input signal that you set to On is received.  
If Auto Sensing is set to Off, the input is not switched when the input signal is received.  
If SIMPLINK is set to On, HDMI is automatically set to Off and can not work.  
If the signal is removed while Auto Sensing (automatic input switch) is enabled, the input returns to the  
previous setting.  
If the several inputs are connected by enabling Auto Sensing and the automatic input switch is performed  
several times, the input returns to the previous setting only for the last input and does not repeat the  
operation for the rest.  
For the AV input connected using the euro scart cable, Auto Sensing does not work for the TV input  
because the Auto AV function is enabled.(For other inputs, Auto Sensing works normally.)  
(6) Forced DVI Audio  
When Forced DVI Audio is selected, the audio signal from the HDMI port will be transmitted through the  
RGB, AV, or Audio In #1 component ports.  
The video signal will be transmitted through HDMI to be displayed on the screen in standard quality.  
For the audio signal, the priority order is the RGB AV Audio In component ports.  
(7) Video Mute  
When Video Mute is set to On, for Blank.  
(8) Noise Mute  
When Noise Mute is set to On, audio mutes when no signal is present.  
(9) Wake On Lan (Depending upon model)  
If set to On, user can turn on the TV by using LAN network.  
(10) DPM  
You can configure the DPM (Display Power Management) function.  
If this option is not set to Off, the TV set enters the DPM mode when there is no input signal. DPM can be  
set to Off / 5 sec / 10 sec / 15 sec / 1 min / 3 min / 5 min / 10 min.  
If you set this option to Off, the DPM function is disabled.  
22  
Time Scheduler  
1
Go to General Configuration Setup Time Scheduler.  
(1) Time Scheduler  
It is a mode to set whether to use or not.  
When Time Scheduler is set to On, You can adjust ON TIME SETTING, OFF TIME SETTING menu.  
(a) ON TIME SETTING  
It sets the time for turning the TV on. A maximum of 7 timers can be set.  
(b) OFF TIME SETTING  
It sets the time for turning the TV off. A maximum of 7 timers can be set.  
Lock Mode  
1
Go to General Lock Mode.  
If Lock Mode Items are set to Off, the following features will be unavailable.  
- Data Service(Teletext, EPG, Sub-Title, Caption (Include MPEG4), MHEG)  
- USB Enable(Exclude S/W update)  
- Factory Reset (Only when Public Display Settings is set to Off.)  
23  
External Speaker  
1
Go to General External Speaker.  
(1) Volume Control  
Selects the volume control method of an external speaker. You can choose either Off/Int Variable or  
Fixed.  
(1) Output  
This item is enabled when Volume Control is set to Fixed. You can choose one of 7 steps.  
(0.01/0.03/0.05/0.1/0.2/0.5/1 Watts)  
Some models can choose one of 9 steps. (0.01/0.03/0.05/0.1/0.2/0.5/1/1.5/2 Watts)  
NOTE  
Optical supported models :  
- If You set External Speaker as Variable Output Mode, User cannot select External Speaker(Optical) in  
Sound-Out menu.  
Headphone supported models :  
- External Speaker and Headphone can not be used simultaneously.  
- Disconnect Headphone to use External Speaker. External Speaker only works when Headphone is  
disconnected.  
24  
Speaker Output Setup  
* Depending upon model  
Connect the external speaker to the external speaker out jack on the TV.  
EXTERNAL  
SPEAKER OUT  
or  
STEREO 8  
VOLUME  
CONTROL  
Control port for Speaker out  
UP  
+
DOWN  
-
GND  
RIGHT  
LEFT  
GND  
: Depending upon model  
NOTE  
External speaker must be used three plug(SE : Single Ended, Stereo) as shown in the drawings and  
external speaker fully inserted with external Speaker Jack.  
Otherwise it will cause defect.  
Use only with the 3 Pole 3.5 mm Stereo Jack.  
Do not connect your headphones or earphones to the port for connecting an external speaker.  
Method of Volume control port  
* Depending upon model  
Cable Spec.  
Each Up / Down pin is pulled to 3.3 V with CPU GPIO.  
CPU detects transition from 3.3 V to GND level for volume control.  
GND / Up / Down  
25  
HCEC Setup  
1
Go to General HCEC Setup.  
(1) HCEC Setup  
When HCEC Setup is set to CEC Mode, You can adjust IR Decoding, Device ID, StandBy menu and  
SIMPLINK feature automatically changed to the on state, and the user can not change this status.  
(a) IR Decoding  
When CEC Mode is set to HCEC Mode, the TV decodes and changes it into a CEC Message and sends  
it to Command via the HDMI CEC Line. The default value is Disable.  
(b) Device ID  
Sets the ID of a device(Logical Address) connected to the CEC Line. You can choose between All and  
E.  
The default value is All.  
(c) Stand By  
Sets the sending and receiving scenario of the operation about [CEC Op standBy(0x0c)  
Command(Device Power)].  
The detailed scenario is described on the table below.  
Send  
Receive  
Send Only  
Receive Only  
All  
O
X
X
O
O
X
O
X
Off  
(2) HTNG HotelMode  
If the following options are selected because of the HTNG command:  
* Power On Default, Start Volume, Maximum Volume, Minimum Volume, then the value for the HTNG  
HotelMode changes automatically to Enable and, even if the HotelMode is set to Disable, the above  
options are still affected.  
If you change it to Disable, then the values set by the HTNG will be canceled.  
26  
Insert Image  
This feature allows you to display an image you have stored on the TV instead of the LG Cube when there is  
no signal due to DTV signal attenuation, external device failure, or cable removal.  
1
Go to General Insert Image.  
(1) Mode  
Select Original, Fit, or Full mode as the mode for Insert Image .  
- Original: displays the original size of the image stored on your USB storage.  
- Fit: displays the image at a size that fits the aspect ratio of the TV.  
- Full: displays the image at a size that fits the full screen of the TV.  
(2) Slide Time  
Select 5, 10, 15, or 20 seconds to display the selected image.  
NOTE  
Only images in a JPG file format can be downloaded and displayed.  
The size of the images to be downloaded should not exceed 10 MB. You can select multiple images to  
download.  
For best results, the resolution of the images downloaded should be 1920 x 1080 (FHD) or smaller.  
For detailed information about downloading images, go to TV Manager Ez Download.  
Non-standard photo/image file may not be displayed.  
27  
Welcome Video  
* (Depending upon model)  
This feature allows you to download videos via USB storage to display on your TV after your TV boots up  
and the boot logo appears.  
1
Go to General Welcome Video.  
(1) Welcome Video  
You can set to Off, Once or Repeat using the  
button  
NOTE  
Operation  
1
The video displays after your TV is turned on and the boot logo appears.  
If Welcome Video is enabled and a video is downloaded on the TV, the video plays.  
The time it takes a video to be displayed may differ depending on the decoding time of the video.  
In case of a corrupted or damaged file, the video may abruptly stop without an error displayed.  
The timer features such as Timer Power Off and Sleep Timer are not available during playback.  
USB Autoplayback starts after the Welcome Video.  
Controls for playing the video are not available. (Pause, stop, fast forward, etc.)  
2
Using the keys  
Only eight keys (Vol +, Vol -, Mute, OK, Exit, CH up, CH down and Back) can be used while playing video.  
The OK, Exit, CH up, CH down, or Back key can cancel playing a video.  
3
Using RS232C  
Only the following commands work: KE(mute), KF (volume), and MC(data – volume, mute, ch).  
4
Downloading  
Videos in any file format that the TV supports can be downloaded and displayed.  
Videos up to 50MB can be downloaded.  
For detailed information about downloading videos, go to TV Manager Ez Download.  
Please do not use the ampersand character(&) and the left angle bracket (<) in the filename to use DZM file  
on EZ Download.  
28  
Clear Video Storage  
* (Depending upon model)  
This feature allows you to delete downloaded videos(Hotel Video and Welcome Video) and reset the feature  
back to default.  
1
Go to General Clear Video Storage.  
Set to Yes or No.  
29  
Crestron  
* (Depending upon model)  
* Image shown may differ from your TV.  
1
Go to General Crestron  
(1) Server  
This menu sets the server’s IP address for the network connection with the server. (Equipment provided  
by Crestron).  
This function enables synchronization with applications provided by Crestron.  
(2) Port (1024~65535)  
This menu sets the port for the network connection with the server. The default port number is 41794.  
(3) IP ID (3~254)  
This menu sets a unique ID for synchronizing with the application.  
30  
Control Server  
* (Depending upon model)  
* Image shown may differ from your TV.  
1
Go to General Control Server  
Set up to connect your TV to a control server.  
31  
NTP Timer Sync  
* (Depending upon model)  
* Image shown may differ from your TV.  
1
Go to General NTP Timer Sync  
(1) NTP Timer Sync  
Enable or disables NTP Timer Sync.  
(2) GMT Offset  
Set GMT(Greenwich Mean Time) offset(hour) of your location.  
NOTE  
This feature allows you to receive time information via NTP(Network Time Protocol) Time Server to set  
Current Clock.  
 
32  
KEY CODES  
* This feature is not available for all models.  
Code  
Code  
(Hexa)  
Function  
(Hexa)  
Note  
Function  
Note  
00  
01  
02  
03  
06  
07  
08  
09  
0B  
/
/
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
45  
4C  
4D  
52  
5B  
61  
63  
71  
72  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
(Dash) /  
(Blue)  
(Power)  
(Mute)  
(Input)  
(Yellow)  
(Green)  
(Red)  
0E  
0F  
R/C Button  
79  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
7C  
8E  
8F  
91  
AA  
B0  
B1  
BA  
--  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
(Home)  
10 - 19 Number Key 0 - 9  
1A  
1E  
28  
39  
40  
41  
/
43  
44  
(Settings)  
R/C Button  
Key code 4C (0 x 4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea,  
Japan, North America, Latin America except Colombia models)  
33  
Customizable Portal  
* (Depending upon model)  
This feature provides Hotel Template and Quick Menu.  
Portal Settings  
(1) Portal Mode  
You can set this mode to None/Customizable.  
- None: Disable Customizable Portal.  
- Customizable: Enter the HOME or PORTAL key to enter Customizable Portal.  
(2) Auto Start  
You can set this mode to On/Off.  
- When set to On, Customizable Portal automatically starts when the TV is On.  
34  
(3) Portal Editor  
Template: You can set Template when selecting focus. Select between Bar Type or Tile Type (City, Beach,  
and Forest).  
Hotel Video: You can set this mode to On/Off when selecting Customizable Portal. You can download it.  
- Off: Disable to play Hotel Video when selecting Customizable Portal.  
- On: You can play Hotel Video when selecting Customizable Portal. You can see the menu only if you have  
downloaded Hotel Video.  
- Download: Copy and paste the video you want to download in the “LG_HOTELfolder in the USB device  
and connect the USB device to a TV.  
- Select Download to go to TV Manager Ez Download. (The download method is the same as the  
existing Ez Download.)  
Reset: Revert edits back to the original state.  
Save: Save the latest changes.  
X: Exit the edit screen. At the time of exit, if changes have been made, a message pops up to ask whether to  
save such changes.  
- Yes: Save and exit  
- No: Reset and exit  
Welcome Message, Hotel Name: Select the focus to set messages.  
HOTEL icon: Select the focus to change the hotel icon.  
- Select images for Off/Default/Download. (Template: for the Bar Type, this feature cannot be set to Off.)  
- You can download and save up to 3 images.  
- Download: Copy and paste the image you want to download in the “LG_HOTELfolder in the USB device  
and connect the USB device to a TV.  
- Select Download to go to TV Manager Ez Download. (The download method is the same as the  
existing Ez Download.)  
- After downloading a file of the image, enter Portal Editor and select the HOTEL icon to select the  
downloaded file.  
35  
Change Item: Move the focus to the item you want to change and enter the OK key. Select a new item from  
the list.  
(4) Hotel Directory  
You can set the information to be displayed in Customizable Portal Hotel Directory.  
You can set this mode to On/Off.  
- When set to Off, this feature cannot be selected as an item in Customizable Portal.  
- If you are already using Hotel Directory in Customizable Portal, this feature cannot be set to Off. (The  
mode is still set to On.)  
You can set up to 7 directories.  
NOTE  
English is the only keyboard language for Welcome Message, Hotel Name, and Hotel Directory.  
36  
Customizable Portal  
1 How to enter: Enter the HOME or PORTAL key.  
(1) Items  
Wake up Time: You can set the On Timer feature. This setting is linked to General Timers Timer Power  
On, and you can set On /Off, Time, and Volume of Timer Power On.  
- While On Timer is operating, the Input and Programme settings are set in accordance with General →  
Timers Timer Power On.  
- Repeat: Operate as Once.  
Audio Channel: Provide a page where you can only set Audio Only Programme.  
Caption: Move to the Subtitles menu. (Move to the Settings page.)  
Channel list (Programme list): If the current input is TV, move to the Programme list. (The UI is the same as  
the existing LIST hotkey.)  
Hotel Directory: Show the set items in Installation Portal Settings Hotel Directory.  
Inputs: Move to the Input settings screen. (The UI is the same as the existing INPUT hotkey).  
My Media: When a USB device is connected, move to My Media. (The UI is the same as the existing My  
Media.)  
Sleep Timer: You can set the sleep timer. (This setting is linked to General Timers Sleep Timer.)  
TV Guide: Move to TV Guide. (The UI is the same as the existing GUIDE hotkey.)  
Hotel Video: You can play Hotel Video as full screen.  
NOTE  
Entry of items in Customizable Portal is in accordance with the settings in Public Display Settings →  
limited Mode.  
When Installation Time Scheduler is set, Wake up Time cannot be entered.  
In models that support Pro:Centric, Interactive, Portal Settings is disabled when the Pro:Centric Mode and  
Interactive Mode are set. (Portal Mode: None, Auto Start: Switched to Off)  
Since the keyboard in Portal Settings only supports English, sub-items of Welcome Message, Hotel Name  
and Hotel Directory in Customizable Portal are displayed in English even if you change the language.  
37  
Audio Channel  
This feature provides list of “Audio Onlychannels.  
* Only available in models with Customizable Portal  
1 Go to Customizable Portal Audio Channel.  
(1) Items  
Move to the first Channel on the list when you enter Audio Channel. (When the current input is Audio  
Channel, the current channel is maintained.)  
Press the  
Press the  
button to switch channels.  
button to move the focus of the list.  
Screen Saver is turned on after 3 minutes of inactivity. Enter any key to go back to the Audio Channel  
screen.  
38  
EXTERNAL CONTROL DEVICE SETUP  
* Image shown may differ from your TV.  
* Cable is not provided.  
* The connection interface may differ from your TV.  
RS-232C Setup  
Connect the USB to Serial converter/RS-232C  
input jack to an external control device (such as a  
computer or an A/V control system) to control the  
product’s functions externally.  
Connect the serial port of the control device to the  
RS-232C jack on the product back panel.  
NOTE  
The type of control port on the TV can be different  
between model series.  
USB to Serial converter with USB Cable  
USB Type  
(TV)  
(PC)  
LG TV supports PL2303 chip-based (Vendor ID : 0 x 0557, Product ID : 0 x 2008) USB to serial converter  
which is not made nor provided by LG.  
It can be purchased from computer stores that carry accessories for IT support professionals.  
RS-232C with RS-232C Cable  
DE9 (D-Sub 9pin) Type  
RS-232C IN  
(CONTROL & SERVICE)  
(PC)  
(TV)  
You need to purchase the RS-232C (DE9, D-Sub 9 pin female-to-female type) to RS-232C cable required for  
the connection between the PC and the TV, which is specified in the manual.  
The connection interface may differ from your TV.  
39  
Connector type : D-Sub 9-pin male  
1
5
6
9
RS-232C  
(Serial port)  
RS-232C configurations  
7-Wire Configurations  
(Standard RS-232C cable)  
3-Wire Configurations  
(Not standard)  
PC  
TV  
PC  
TV  
RXD  
TXD  
GND  
DTR  
DSR  
RTS  
2
3
5
4
6
7
8
3
TXD  
RXD  
GND  
DTR  
DSR  
RTS  
RXD  
TXD  
GND  
DTR  
DSR  
RTS  
2
3
5
4
6
7
8
3
2
5
6
4
8
7
TXD  
RXD  
GND  
DTR  
DSR  
RTS  
2
5
6
4
8
7
CTS  
CTS  
CTS  
CTS  
D-Sub 9  
D-Sub 9  
D-Sub 9  
Set ID  
For Set ID number, see “Real data mapping (Hexadecimal : Decimal)”.  
1
2
3
4
Press (Settings) to access the main menus.  
Press the Navigation buttons to scroll to (* General Set ID) and press  
button.  
Scroll left or right to select a set ID number and select  
When you are finished, press  
. The adjustment range is 1-99.  
.
40  
Communication Parameters  
Baud rate : 9600 bps (UART)  
Data length : 8 bits  
Parity : None  
Stop bit : 1 bit  
Communication code : ASCII code  
Use a crossed (reverse) cable.  
Command reference list  
* (Depending on model)  
COMMAND1  
COMMAND2  
DATA (Hexadecimal)  
1
2
3
4
5
6
7
8
9
Power  
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
x
j
a
c
d
e
f
00 to 01  
(page 42)  
(page 42)  
00 to 01  
00 to 64  
00 to 64  
00 to 64  
00 to 64  
00 to 64  
00 to 32  
00 to 01  
00 to 01  
00 to 64  
00 to 64  
00 to 64  
00 to 64  
(page 44)  
00 to 05  
(page 44)  
00 to 01  
Key Codes  
00 to 64  
(page 47)  
(page 47)  
Aspect Ratio  
Screen Mute  
Volume Mute  
Volume Control  
Contrast  
Brightness  
Color  
Tint  
g
h
i
j
10 Sharpness  
11 OSD Select  
12 Remote Control Lock Mode  
13 Treble  
14 Bass  
15 Balance  
16 Color Temperature  
17 Equalizer  
18 Energy Saving  
19 Tune Command  
20 Channel Skip/Add  
21 Key  
22 Control Backlight  
23 Input select  
24 Auto Configure  
k
l
m
r
s
t
u
v
q
a
b
c
g
b
u
j
m
m
m
m
x
j
During playing media, all commands except Power (ka) and Key (mc) are not executed and treated as NG.  
With RS-232C cable, TV can communicate “ka commandin power-on or power-off status. But with USB-to-  
Serial converter cable, the command works only if TV is on.  
41  
TRANSMISSION / RECEIVING PROTOCOL  
* (Depending on Model)  
Transmission  
[Command1][Command2][ ][Set ID][ ][Data][Cr]  
[Command 1] : First command to control the TV. (j, k, m or x)  
[Command 2] : Second command to control the TV.  
[Set ID] : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is  
1 to 99. When selecting Set ID ‘0, every connected set is controlled. Set ID is indicated as decimal (1 to 99) on  
menu and as Hexa decimal (0 x 0 to 0 x 63) on transmission/receiving protocol.  
[Data] : To transmit command data (hexadecimal). Transmit ‘FFdata to read status of command.  
[Cr] : Carriage Return - ASCII code ‘0 x 0D’  
[ ] : Space – ASCII code ‘0 x 20’  
OK Acknowledgement  
[Command2][ ][Set ID][ ][OK][Data][x]  
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if  
the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data  
of the PC computer.  
Error Acknowledgement  
[Command2][ ][Set ID][ ][NG][Data][x]  
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-  
viable functions or communication errors.  
Data 00: Illegal Code  
Real data mapping (Hexadecimal : Decimal)  
* When you enter the [Data] in hexadecimal, refer to following conversion table.  
* Channel Tune (ma) Command uses two-byte hexadecimal value([Data]) to select channel number.  
00 : Step 0  
32 : Step 50 (Set ID 50)  
FE : Step 254  
01 : Step 1 (Set ID 1)  
33 : Step 51 (Set ID 51)  
FF : Step 255  
...  
...  
...  
0A : Step 10 (Set ID 10)  
63 : Step 99 (Set ID 99)  
01 00 : Step 256  
...  
...  
...  
0F : Step 15 (Set ID 15)  
10 : Step 16 (Set ID 16)  
...  
C7 : Step 199  
C8 : Step 200  
...  
27 0E : Step 9998  
27 0F : Step 9999  
...  
 
42  
1 Power (Command: k a)  
3 Screen Mute (Command: k d)  
To control power on or off of the set.  
Transmission  
To select screen mute on/off.  
Transmission  
[k][a][ ][Set ID][ ][Data][Cr]  
[k][d][ ][Set ID][ ][Data][Cr]  
Data 00 : Off  
Data 01 : On  
Data 00 : Screen mute off (Picture on) / Video mute  
off  
Data 01 : Screen mute on (Picture off)  
Data 10 : Video mute on  
Ack  
[a][ ][Set ID][ ][OK/NG][Data][x]  
Ack  
To show TV is power on or *Off  
Transmission  
[d][ ][Set ID][ ][OK/NG][Data][x]  
* In case of video mute on only, TV will display On  
Screen Display(OSD). But, in case of Screen mute  
on, TV will not display OSD.  
[k][a][ ][Set ID][ ][FF][Cr]  
Ack  
[a][ ][Set ID][ ][OK/NG][Data][x]  
4 Volume Mute (Command: k e)  
* Similarly, if other functions transmit ‘FFdata  
based on this format, Acknowledgement  
feedback presents status about each function.  
To control volume mute on/off. You can also  
adjust mute using the mute button on remote  
control.  
* OK Ack., Error Ack. and other message may  
display on the screen when TV is power on.  
Transmission  
[k][e][ ][Set ID][ ][Data][Cr]  
Data 00 : Volume mute on (Volume off)  
Data 01 : Volume mute off (Volume on)  
2 Aspect Ratio (Command: k c) (Main Picture Size)  
To adjust the screen format. (Main picture  
format) You can also adjust the screen format  
using the picture settings.  
Ack  
[e][ ][Set ID][ ][OK/NG][Data][x]  
Transmission  
5 Volume Control (Command: k f)  
[k][c][ ][Set ID][ ][Data][Cr]  
To adjust volume. You can also adjust volume  
Data 01 : 4:3 (Normal screen - Just Scan Off)  
Data 02 : 16:9 (Wide screen - Just Scan Off)  
Data 06 : Original (Just Scan Off)  
Data 09 : Just Scan  
with the volume buttons on remote control.  
Transmission  
[k][f][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
Ack  
[c][ ][Set ID][ ][OK/NG][Data][x]  
* Using the PC input, you select either 16:9 or 4:3  
screen aspect ratio.  
[f][ ][Set ID][ ][OK/NG][Data][x]  
* In DTV/HDMI/Component mode (high-  
definition), Just Scan is available.  
6 Contrast (Command: k g)  
To adjust screen contrast. You can also adjust  
contrast in the picture settings.  
* Full wide mode may work differently based on  
model and is supported for DTV fully, and ATV,  
AV partially.  
Transmission  
[k][g][ ][Set ID][ ][Data][Cr]  
Ack  
[g][ ][Set ID][ ][OK/NG][Data][x]  
   
43  
7 Brightness (Command: k h)  
11 OSD Select (Command: k l)  
To adjust screen brightness. You can also adjust  
brightness in the picture settings.  
To select OSD (On Screen Display) on/off when  
controlling remotely.  
Transmission  
Transmission  
[k][h][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
[k][l][ ][Set ID][ ][Data][Cr]  
Data 00 : Off  
Data 01 : On  
Ack  
[h][ ][Set ID][ ][OK/NG][Data][x]  
[l][ ][Set ID][ ][OK/NG][Data][x]  
8 Color (Command: k i)  
12 Remote Control Lock Mode (Command: k m)  
To adjust the screen color. You can also adjust  
colour in the picture settings.  
To lock the front panel controls on the monitor  
and remote control.  
Transmission  
Transmission  
[k][i][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
[k][m][ ][Set ID][ ][Data][Cr]  
Data 00 : Off  
Data 01 : On  
[i][ ][Set ID][ ][OK/NG][Data][x]  
Ack  
[m][ ][Set ID][ ][OK/NG][Data][x]  
9 Tint (Command: k j)  
* If you are not using the remote control, use this  
mode. When main power is off & on (plug-off and  
plug-in, after 20 - 30 seconds), external control  
lock is released.  
To adjust the screen tint. You can also adjust  
colour in the picture settings.  
Transmission  
[k][j][ ][Set ID][ ][Data][Cr]  
Data Red : 00 to Green : 64  
Ack  
* In the standby mode (DC off by off timer or ‘ka,  
‘mccommand), and if key operation is on, TV will  
not turn on by power on key of IR & Local Key.  
[j][ ][Set ID][ ][OK/NG][Data][x]  
13 Treble (Command: k r)  
(Depending on model)  
10 Sharpness (Command: k k)  
To adjust treble. You can also adjust Treble in the  
audio settings.  
To adjust the screen sharpness. You can also  
adjust sharpness in the picture settings.  
Transmission  
Transmission  
[k][r][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
[k][k][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 32  
Ack  
[r][ ][Set ID][ ][OK/NG][Data][x]  
[k][ ][Set ID][ ][OK/NG][Data][x]  
44  
14 Bass (Command: k s)  
Ack  
(Depending on model)  
[v][ ][Set ID][ ][OK/NG][Data][x]  
To adjust bass. You can also adjust Bass in the  
* It depends on model, and can adjust when sound  
mode is EQ adjustable value.  
audio settings.  
Transmission  
18 Energy Saving (Command: j q)  
(Depending on model)  
[k][s][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
To reduce the power consumption of the TV. You  
can also adjust energy saving in picture settings.  
[s][ ][Set ID][ ][OK/NG][Data][x]  
Transmission  
[j][q][ ][Set ID][ ][Data][Cr]  
15 Balance (Command: k t)  
Data 00 : Off  
To adjust balance. You can also adjust balance in  
the audio settings.  
Data 01 : Minimum  
Data 02 : Medium  
Data 03 : Maximum  
Data 04 : Auto  
Transmission  
[k][t][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
Data 05 : Screen off  
Ack  
[q][ ][Set ID][ ][OK/NG][Data][x]  
[t][ ][Set ID][ ][OK/NG][Data][x]  
19 Tune Command (Command: m a)  
* This command may work differently depending  
on model and signal.  
16 Color Temperature (Command: x u)  
To adjust colour temperature. You can also  
adjust color temperature in the picture settings.  
* For Europe, Mid-East, Colombia, Asia except  
South Korea and Japan Model  
Transmission  
[x][u][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
Select channel to following physical number.  
Transmission  
[m][a][ ][Set ID][ ][Data 00][ ][Data 01]  
[u][ ][Set ID][ ][OK/NG][Data][x]  
[ ][Data 02][Cr]  
17 Equalizer (Command : j v)  
Analog Antenna/Cable  
Adjust EQ of the set.  
Transmission  
[Data 00][Data 01] Channel Data  
Data 00 : High byte channel data  
Data 01 : Low byte channel data  
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)  
Data 02 : Input Source (Analog)  
- 00 : Antenna TV (ATV)  
[j][v][ ][Set ID][ ][Data][Cr]  
MSB  
0
LSB  
0
0
0
0
0
0
0
- 80 : Cable TV (CATV)  
Frequency  
Data  
7
0
0
0
0
1
6
0
0
1
1
0
5
0
1
0
1
0
Frequency  
1st Band  
2nd Band  
3rd Band  
4th Band  
5th Band  
4
3
0
0
2
1
0
0
0
0
1
Step  
0
0
0
0
0(decimal)  
1(decimal)  
...  
... ... ... ... ...  
1
1
0
0
0
1
1
0
1
0
19(decimal)  
20(decimal)  
   
45  
Digital Antenna/Cable/Satellite  
- Digital channels have a Physical, Major, and  
Minor channel number. The Physical number is  
the actual digital channel number, the Major is  
the number that the channel should be mapped  
to, and the Minor is the sub-channel. Since the  
ATSC tuner automatically maps the channel from  
the Major / Minor number, the Physical number  
is not required when sending a command in  
Digital.  
[Data 00][Data 01]: Channel Data  
Data 00 : High byte channel data  
Data 01 : Low byte channel data  
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)  
Data 02 : Input Source (Digital)  
- 10 : Antenna TV (DTV)  
- 20 : Antenna Radio (Radio)  
- 40 : Satellite TV (SDTV)  
- 50 : Satellite Radio (S-Radio)  
- 90 : Cable TV (CADTV)  
Analog Antenna/Cable  
Data 00 : Physical Channel Number  
- a0 : Cable Radio (CA-Radio)  
- Antenna (ATV) : 02~45 (Decimal: 2  
~ 69)  
- Cable (CATV) : 01, 0E~87 (Decimal : 1,  
14~135)  
Tune Command Examples:  
1
Tune to the Analog antenna (PAL) Channel 10.  
Set ID = All = 00  
[Data 01 ~ 04]: Major/Minor Channel Number  
Data 01 & 02: xx (Don’t care)  
Data 00 & 01 = Channel Data is 10 = 00 0a  
Data 02 = Analog Antenna TV = 00  
Result = ma 00 00 0a 00  
Data 03 & 04: xx (Don’t care)  
Data 05: Input Source (Analog)  
2
Tune to the digital antenna (DVB-T) Channel  
01.  
- 00 : Antenna TV (ATV)  
- 01 : Cable TV (CATV)  
Set ID = All = 00  
Digital Antenna/Cable  
Data 00 & 01 = Channel Data is 1 = 00 01  
Data 02 = Digital Antenna TV = 10  
Result = ma 00 00 01 10  
Data 00 : xx (Don’t care)  
[Data 01][Data 02]: Major Channel Number  
Data 01 : High byte Channel Data  
Data 02 : Low byte Channel Data  
3
Tune to the satellite (DVB-S)  
Channel 1000.  
Set ID = All = 00  
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)  
Data 00 & 01 = Channel Data is 1000 = 03 E8  
Data 02 = Digital Satellite TV = 40  
Result = ma 00 03 E8 40  
[Data 03][Data 04]: Minor Channel Number  
Data 03 : High byte Channel Data  
Data 04 : Low byte Channel Data  
Data 05 : Input Source (Digital)  
Ack  
[a][ ][Set ID][ ][OK][Data 00][Data 01]  
- 02 : Antenna TV (DTV) – Use Physical  
Channel Number  
- 06 : Cable TV (CADTV) – Use Physical  
Channel Number  
- 22 : Antenna TV (DTV) – Don’t Use  
Physical Channel Number  
- 26 : Cable TV (CADTV) - Don’t Use  
Physical Channel Number  
- 46 : Cable TV (CADTV) – Use Major  
Channel Number Only (One Part  
Channel)  
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]  
* For South Korea, North/Latin America except  
Colombia Model  
To tune channel to following physical/major/  
minor number.  
Transmission  
[m][a][ ][0][ ][Data 00][ ][Data 01][ ]  
[Data 02][ ][Data 03][ ][Data 04][ ][Data 05][Cr]  
* Two bytes are available for each major and minor  
channel data, but usually the low byte is used  
alone (high byte is 0).  
46  
Tune Command Examples:  
Tune Command Examples:  
1
Tune to the Analog cable (NTSC) channel 35.  
1
Tune to the digital antenna (ISDB-T) channel  
17-1.  
Set ID = All = 00  
Data 00 = Channel Data is 35 = 23  
Data 01 & 02 = No Major = 00 00  
Data 03 & 04 = No Minor = 00 00  
Data 05 = Analog Cable TV = 01  
Total = ma 00 23 00 00 00 00 01  
Set ID = All = 00  
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 17 = 00 11  
Data 03 & 04 = Minor/Branch is 1 = 00 01  
Data 05 = Digital Antenna TV = 02  
Total = ma 00 00 00 11 00 01 02  
2
Tune to the digital antenna (ATSC) channel  
30-3.  
2
Tune to the BS (ISDB-BS) channel 30.  
Set ID = All = 00  
Set ID = All = 00  
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 30 = 00 1E  
Data 03 & 04 = Minor is 3 = 00 03  
Data 05 = Digital Antenna TV = 22  
Total = ma 00 00 00 1E 00 03 22  
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 30 = 00 1E  
Data 03 & 04 = Don’t Care = 00 00  
Data 05 = Digital BS TV = 07  
Total = ma 00 00 00 1E 00 00 07  
* This feature is varied based on the model.  
Ack  
Ack  
[a][ ][Set ID][ ][OK][Data 00][Data 01][Data 02]  
[Data 03][Data 04][Data 05][x][a][ ][Set ID][ ]  
[NG][Data 00][x]  
[a][ ][Set ID][ ][OK][Data 00][Data 01]  
[Data 02][Data 03][Data 04][Data 05]  
[x][a][ ][Set ID][ ][NG][Data 00][x]  
* For Japan Model  
20 Channel Skip/Add (Command: m b)  
To tune channel to following physical/major/  
minor number.  
To skip current channel for next time.  
Transmission  
Transmission  
[m][a][ ][0][ ][Data 00][ ][Data 01][ ][Data 02]  
[m][b][ ][Set ID][ ][Data][Cr]  
Data 00 : Del(ATSC,ISDB)/Skip(DVB)  
Data 01 : Add  
[ ][Data 03][ ][Data 04][ ][Data 05][Cr]  
Ack  
Digital Antenna/Satellite  
[b][ ][Set ID][ ][OK/NG][Data][x]  
Data 00 : xx (Don’t care)  
[Data 01][Data 02] : Major Channel Number  
Data 01 : High byte Channel Data  
Data 02 : Low byte Channel Data  
* Set the saved channel status to del(ATSC, ISDB)/  
skip(DVB) or add.  
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)  
21 Key (Command: m c)  
[Data 03][Data 04] : Minor/Branch Channel  
Number (Don’t care in Satellite)  
To send IR remote key code.  
Transmission  
Data 03 : High byte Channel Data  
Data 04 : Low byte Channel Data  
Data 05 : Input Source (Digital/Satellite for Japan)  
[m][c][ ][Set ID][ ][Data][Cr]  
Data : Key code - page 31  
Ack  
- 02 : Antenna TV (DTV)  
- 07 : BS (Broadcasting Satellite)  
- 08 : CS1 (Communication Satellite 1)  
- 09 : CS2 (Communication Satellite 2)  
[c][ ][Set ID][ ][OK/NG][Data][x]  
47  
22 Control Backlight (Command: m g)  
To control the backlight.  
Transmission  
[m][g][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack  
[g][ ][Set ID][ ][OK/NG][Data][x]  
23 Input select (Command: x b) (Main Picture  
Input)  
To select input source for main picture.  
Transmission  
[x][b][ ][Set ID][ ][Data][Cr]  
Data 00 : DTV  
Data 01 : CADTV  
Data 02 : Satellite DTV ISDB-BS (Japan)  
Data 03 : ISDB-CS1 (Japan)  
Data 04 : ISDB-CS2 (Japan)  
Data 10 : ATV  
Data 11 : CATV  
Data 20 : AV or AV1  
Data 21 : AV2  
Data 40 : Component1  
Data 41 : Component2  
Data 60 : RGB  
Data 90 : HDMI1  
Data 91 : HDMI2  
Data 92 : HDMI3  
Data 93 : HDMI4  
Ack  
[b][ ][Set ID][ ][OK/NG][Data][x]  
* This function depends on model and signal.  
24 Auto Configure (Command: j u)  
(Depending on model)  
To adjust picture position and minimize image  
shaking automatically. It works only in RGB (PC)  
mode.  
Transmission  
[j][u][ ][Set ID][ ][Data][Cr]  
Data 01 : To set  
Ack  
[u][ ][Set ID][ ][OK/NG][Data][x]  
   

Tekkeon Mp2250 User Manual
Sanyo Kh2672r User Manual
Samsung Aw07l2 User Manual
Ryobi P110 User Manual
Microboards Technology Cd Disc To Disc Office Copier Ii User Manual
MAKITA UH303D User Manual
EPSON ACULASER MX21 User Manual
DELL XPS 13 9370 User Manual
DELL SE2422H User Manual
ACER EXTENSA 5510Z User Manual