us_main.book.book Page 1 Tuesday, March 31, 2020 5:28 PM
OWNER'S MANUAL
A9 S
• Charge the battery fully before first use.
• Read the Safety Instructions before using the product.
• After reading this manual, keep it in an easily accessible location.
Copyright © 2020 LG Electronics Inc. All Rights Reserved
MFL69883639
us_main.book.book Page 3 Tuesday, March 31, 2020 5:28 PM
3
TABLE OF CONTENTS
4 IMPORTANT SAFETY
INSTRUCTIONS
4
4
8
READ ALL INSTRUCTIONS BEFORE USE
WARNING STATEMENTS
CAUTION STATEMENTS
9 INSTALLATION
9
Product Overview
12 Installing the Charging Station
15 Storing the Accessories
16 OPERATION
16 Getting Started
18 Charging the Battery
18 Using the Nozzles and Tools
21 SMART FUNCTIONS
21 Using LG ThinQ Application
24 Smart Diagnosis™ Function
25 MAINTENANCE
25 Cleaning the Appliance
27 Cleaning the Nozzle
29 TROUBLESHOOTING
29 Before Calling for Service
31 LIMITED WARRANTY
31 USA
34 APPENDIX
34 U.S. Patent Protection
us_main.book.book Page 4 Tuesday, March 31, 2020 5:28 PM
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING STATEMENTS
WARNING
• To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this
product, follow basic precautions, including the following:
Technical Safety
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not allow children to play with or hang on the appliance.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges
or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Place the cords from other appliances out of the area to be cleaned.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will
ensure that the safety of the product is maintained.
us_main.book.book Page 5 Tuesday, March 31, 2020 5:28 PM
IMPORTANT SAFETY INSTRUCTIONS
5
Battery
• Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
• Never use the battery, adapter, and the charging station from other appliances with this appliance. Use
only the battery and the charging station provided by LG Electronics.
• Use appliances only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another battery pack.
• Never use the battery, adapter, and the charging station from this appliance with other appliances.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not disassemble, remove or short-circuit the battery.
• Have the battery replaced when it is no longer able to hold a charge.
• Refer to the Charging the Battery section instructions for the method of replacing the battery.
• When disposing of this appliance, follow regulations for disposal of rechargeable lithium-ion batteries.
• Follow all local ordinances and regulations when handling or disposing of the battery.
• Disconnect battery pack before cleaning or servicing.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack,
picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing
appliances that have the switch on invites accidents.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories,
or storing appliance. Such preventive safety measures reduce the risk of starting the appliance
accidentally.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a connection from one terminal to another. Shorting
the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery. If this happens, avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated
in the instructions for use and care.
Battery Specifications
• One or two batteries are provided. The number of batteries varies depending on the model purchased.
- Model Name: EAC63382204
- Type: Rechargeable Lithium-ion Battery
- Rated Capacity: DC 25.2 V, 2.4 Ah/60.48 Wh(Min. 2.3 Ah/57.96 Wh)
Installation
• To avoid an electrical shock or fire, do not install, charge or store the appliance where it may be exposed
to water, rainfall or high humidity.
• Install, charge and store the appliance in a well-ventilated place.
• Avoid operating the appliance in areas where there is a risk of leakage of flammable gas, industrial oil or
metallic dust.
• Do not store or install the appliance, power cord or plug near heating devices or open flames.
• Install the charging station on a firm, level surface.
us_main.book.book Page 6 Tuesday, March 31, 2020 5:28 PM
6
IMPORTANT SAFETY INSTRUCTIONS
• To prevent tipping, self-standing mode installations should be anchored to the wall using the provided
stand anchoring screw, anchoring block and double-sided tape.
• In wall-mounted mode installations, the charging station should be secured tightly to the wall using the
provided wall anchoring screws.
• Use the anchoring screws only when attaching to concrete or similar solid surfaces.
• Never drill into a wall without first checking that the area behind it is free from power conduits,
plumbing, vents, or cables.
• Do not use or store the appliance at temperatures below 41 °F (5°C) or above 100 °F (38°C).
• Do not store or install the appliance where it is exposed to temperatures below freezing or exposed to
outdoor weather conditions.
• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord or
plug.
Operation
• Read all instructions before using the appliance, and save these instructions.
• Use only as described in this manual. Use only manufacturer’s recommended attachment.
• This appliance is designed for normal indoor domestic use only. It is not to be used for any non-
residential, commercial, or industrial application.
• Do not use or store the appliance in any outdoor location, garage environment or on wet surface.
• This product should only be used with a 100 V - 240 V~ 50/60 Hz outlet. Make sure to check the
power specifications of the place where you intend to use the appliance.
• Do not handle the power cord, plug, or appliance controls with wet hands.
• Wipe any moisture or dirt off the cord or plug with a dry cloth.
• Unplug the power cord using the plug, not the cord. Pulling on the cord can damage it and result in
electric shock or fire.
• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged cord or plug. Take it to an authorized LG Electronics
service center or dealer for assistance.
• Do not apply excessive force to the power cord to bend it, or place it under a heavy object as this will
damage it.
• Do not use multiple-outlet adapters with this appliance. Make sure to use a power socket with a capacity
of 10 A.
• Do not plug the appliance into a damaged or loose outlet.
• Make sure to unplug the power cord when the appliance is not to be used for an extended period of
time.
• Do not damage, alter, excessively bend, twist, pull, pinch or heat the power cord.
• Before using the appliance, remove any wire or string on the floor.
• Avoid touching the prongs of the power plug with your finger(s) when unplugging the power cord.
• Do not cover the power cord with a rug or carpeting.
• Push the power plug firmly into the wall outlet so that it is not loose.
• If the product has been submerged, contact an LG Electronics service center or dealer for instructions
before resuming use.
• If the product makes a strange noise or emits an odor or smoke, discontinue use and contact an LG
Electronics customer information center.
• Only qualified technicians or service personnel from LG Electronics may disassemble, repair or modify
the appliance.
• Never insert a sharp metallic object such as a pin, nail or knife in a hole or gap in the appliance or the
charging station.
us_main.book.book Page 7 Tuesday, March 31, 2020 5:28 PM
IMPORTANT SAFETY INSTRUCTIONS
7
• Do not vacuum liquids with this appliance. Make sure that no water, beverage or detergent gets inside
the appliance or the charging station.
• Do not allow the appliance to sweep up blades, thumb tacks, sawdust, sharp objects, or hot or cold
ashes.
• Do not allow children to use the appliance.
• Do not let children or pets get close to the appliance when using, charging or storing.
• Do not insert the nozzle or tools in your mouth.
• Keep clothing and hair, fingers, or other parts of the body away from openings and moving parts.
• Do not operate the appliance with the suction inlet or outlet blocked.
• Do not use in an enclosed space where vapors are present from paint thinner, mothproofing substances,
flammable dust or other explosive or toxic materials.
• Make sure that the filter is installed before use.
• Do not use with the dust bin opened.
• Do not touch the charging terminals on the appliance or the charging station, or insert an electrified
object inside the appliance or the station.
• Always store the appliance on the self-standing or wall-mounted charging station when it is not in use.
• Do not lean the appliance on walls, chairs or tables.
• If the earth leakage breaker is tripped when the product is put on the charging station, immediately
remove the appliance from the charging station. Contact an LG Electronics customer service center.
• Use extra care when cleaning on stairs.
• Do not use or store a heating device or flammable substance (ether, benzene, alcohol, chemicals,
combustible sprays, insecticide, air freshener or cosmetics) in close proximity to the appliance.
• Do not attempt to clean up a liquid substance (water, beverage), odorous substances (candy, chocolate,
pet excrement), metallic objects (blades, pins), flammable substances, surfactants, or glass shards with
this appliance.
• In the event of a gas leak (natural gas, propane gas, etc.) do not operate this or any other appliance.
Open a window or door to ventilate the area immediately.
• Do not hold the charging station upside down with the battery in the charging station.
• Do not expose the appliance, and the battery in particular, to heat, a heating device or direct sunlight.
• Do not keep the appliance or its battery inside a vehicle which is exposed to direct sunlight.
• Never allow any water, beverage or detergent to get inside the battery.
• Do not apply physical impacts to the battery.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair,
and anything that may reduce air flow.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they
may be present.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust bag and/or filters in place.
Maintenance
• Make sure to unplug the power cord when cleaning or maintaining the charging station.
• Do not wash the inlet port or the dust bin with water or detergent.
• Do not use detergents, polishes or air fresheners to clean the dust bin.
• Do not apply or spray a flammable substance (gasoline or thinner) or surfactants (detergent or bath
soap) on the appliance.
• Wash hands after handling nozzles. The nozzles contain carbon fiber, and contact may cause minor skin
irritation.
us_main.book.book Page 8 Tuesday, March 31, 2020 5:28 PM
8
IMPORTANT SAFETY INSTRUCTIONS
Disposal
• Keep packing materials out of the reach of children. Packaging materials can pose a suffocation risk for
children.
• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children
might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight
chambers.
• Dispose of this appliance according to local, state, and regional laws and regulations.
• Contact your local city council or the related government authority before disposing of this appliance.
• In case rechargeable battery is included in this product, the entire device should be recycled in
compliance with rechargeable battery recycling standards because of the internal battery. To dispose of
CAUTION STATEMENTS
CAUTION
• To reduce the risk of injury to persons, malfunction, or damage to the product or property when using
the appliance, follow basic safety precautions, including the following:
Operation
• This appliance has a built-in safety device to prevent damage from overheating. If the appliance
becomes overheated after extended use, it may automatically turn off. If this occurs, leave the appliance
in a cool, well-ventilated area for about an hour before turning on the power again.
• Do not subject the product to shocks or drop it.
• Secure the appliance in the charging station when not in use, to avoid it falling over.
• Do not install wet or damp filters.
• Make sure to wipe up any liquid such as water or oil or pet excrement from the floor before using the
appliance.
• Do not clean the product with a volatile or organic solvent (thinner or acetone).
• Always use a soft cloth to clean the appliance.
• Remain aware of your surroundings while using the appliance to avoid colliding with people or animals.
• Do not kick or apply force to the appliance.
• Do not put any object other than the appliance, especially a metallic or magnetic object, on the charging
station.
• Do not clean the same spot repeatedly for an extended period of time.
• Vibration from the inlet port or rotating brush may damage the floor or the carpet.
• Keep fingers away from pinch points when assembling the appliance or the charging station.
• Do not let a child or a pet hang onto the charging station.
• Follow all applicable state and local codes and regulations when installing the mounting station.
• Do not use the double-sided tape to anchor the charging station on wallpaper. Use the provided screws
to anchor the charging station. The weight of the charging station and the appliance could damage the
paper.
• Do not apply force or any impact to the cyclonic mesh filter.
• Do not remove the battery during operation.
SAVE THESE INSTRUCTIONS
us_main.book.book Page 9 Tuesday, March 31, 2020 5:28 PM
INSTALLATION
9
INSTALLATION
Product Overview
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
NOTE
• For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction, property damage or bodily injury caused by the use of separately
purchased unauthorized components, parts, or non-LG products.
• The floor stand dock and floor stand pipe are not installed in wall-mount installation.
Front View
†: This feature is only available on some models.
a Charging Station
b Auxiliary Charging Station
c Battery (Dual Battery†)
d Product Body
k Exhaust Filter
l Pre-filter
m Kompressor Lever
n Cyclonic Mesh Filter
e Extension Pipe
f Nozzle
g Floor Stand Dock
h Floor Stand Pipe
i Adapter
j Tool Holders
us_main.book.book Page 10 Tuesday, March 31, 2020 5:28 PM
10 INSTALLATION
Installation Kit
Accessories
†: This accessory is only available on some models.
Included Accessories
a Wall Anchoring Block†
b Double-Sided Tape†
c Drywall Anchor†
d Wall Anchoring Screw†
e Stand Anchoring Screw†
Tools and Accessory Bag
a Charging Station
b Extension Pipe
c Adapter
d Pre-filter
e Battery (Dual Battery†)
f Floor Stand Dock†
g Floor Stand Pipe†
a Hard Dirt Tool†
b Mattress Tool†
c Multi-angle Tool†
d Flexible Crevice Tool†
e Flexible Hose Extension†
f Accessory Bag†
Basic Accessories
a Combination Tool
b Crevice Tool
NOTE
• The batteries, exhaust filter and the pre-filter will
eventually need to be replaced. Contact an LG
Electronics customer service center.
c Cleaning Brush
Nozzles
a Power Carpet Nozzle†
b Power Punch Nozzle†
us_main.book.book Page 11 Tuesday, March 31, 2020 5:28 PM
11
INSTALLATION
Specifications
Appliance
Model
A9**********
Dimensions
(Width X Depth X Height)
10.2 in X 10.6 in X 44.1 in
260 mm X 270 mm x 1120 mm
Weight
Approximately 5.67 lb (2.57 kg)
Power Consumption
370 W in Turbo Mode (Maximum 590 W)
120 W in Power Mode
68 W in Normal Mode
Battery Run Time
(Using two battery)
Using with the Power Drive
Nozzle
Using Nozzles other t an the
h
Power Drive Nozzle
Up to 12 minutes in Turbo Mode
Up to 40 minutes in Power Mode
Up to 14 minutes in Turbo Mode
Up to 60 minutes in Power Mode
Up to 80 minutes in Normal Mode Up to 120 minutes in Normal Mode
Using with the Power Drive
Nozzle
Up to 6 minutes in Turbo Mode
Up to 20 minutes in Power Mode
Using Nozzles other than the
Power Drive Nozzle
Up to 7 minutes in Turbo Mode
Up to 30 minutes in Power Mode
Battery Run Time
(Using one battery)
Up to 40 minutes in Normal Mode Up to 60 minutes in Normal Mode
Charger Adaptor
ADC-30FSA-30 29430EPCU
100 V - 240 V~, 50/60 Hz, 0.8 A
DC 29.4 V, 1.0 A
Model
Input
Output
• Dimensions are given for the assembled product body, extension pipe and nozzle.
• Battery run time is the result of using a fully charged battery according to the LG Electronics test
standard. Results may be different depending on actual use environment and period of use.
• The Power Drive Nozzle contains the direct drive motor that rotates the nozzle cleaning head directly.
us_main.book.book Page 12 Tuesday, March 31, 2020 5:28 PM
12 INSTALLATION
Installing the Charging
Station
CAUTION
• Keep fingers away from pinch points when
assembling the appliance or the charging
station.
WARNING
• To prevent tipping, self-standing mode
installations should be anchored to the wall
using the provided stand anchoring screw,
anchoring block and double-sided tape.
CAUTION
• Do not allow children or pets to hang onto the
charging station. They could be injured or cause
damage to the appliance.
• Take care not to drop the product parts while
unpacking them to avoid appliance damage or
personal injury.
• Do not use double-sided tape to attach the
charging station to wallpaper. The weight of the
charging station and the product body could
damage the paper.
NOTE
• The charging station can be removed as needed.
To remove it, hold the floor stand dock steady
and pull up on the charging station.
• Use the stand anchoring screw on concrete or
solid walls. If the appliance is not anchored
securely and falls, it could result in damage to
property or the product.
NOTE
• Once assembled, the floor stand dock and the
floor stand pipe cannot be disassembled.
• The cost of a service call to install or reinstall the
charging station is not covered under the
warranty.
1
2
Place the floor stand dock on a hard and level
floor and assemble the floor stand pipe.
Self-Standing Installation
Follow the steps below to install the charging
station on a hard and level floor.
Clip the power cord tidily into the cord keeper
a on the back of the floor stand pipe.
us_main.book.book Page 13 Tuesday, March 31, 2020 5:28 PM
INSTALLATION 13
3
Assemble the charging station onto the top of
the floor stand pipe.
7
Plug the power cord into the power outlet.
Using Double-Sided Tape to Secure the
Appliance
1
Use the double-sided tape a to attach the
wall anchoring block b to the charging
station.
4
5
Connect the power adapter to the port on the
back of the charging station.
• Remove the center section of double-sided
tape before attaching it to the wall
anchoring block.
Drill a hole in the wall and insert the drywall
anchor b if needed.
• Before drilling, make sure that there are no
pipes or electrical wires inside the wall at
the desired location.
2
Attach the second piece of double-sided tape
to the other side of the wall anchoring block
to secure it to the wall.
• For drywall anchor: use 1/4″ (6.5 mm) drill
bit
• For concrete or wall stud: use 1/8″ (3 mm)
drill bit
• Do not use double-sided tape on wallpaper.
• If screwing into drywall, use the drywall
anchor.
6
Align the wall anchoring block c of the
chanrging station, and fix the charging station
to the wall by tightening the anchoring screw
d all the way.
us_main.book.book Page 14 Tuesday, March 31, 2020 5:28 PM
14 INSTALLATION
Wall-Mounted Installation
For wall-mounted installations, the charging
station must be attached securely to the wall using
the provided (short) wall anchoring screws.
Compact Installation
For safety and convenience, install the charging
station using the self-standing or wall-mounted
installation methods. If you choose not to install
the charging station, place it on a level floor for
charging or storage.
• The detachable nozzle storage cannot be
attached to the charging station in a wall-
mounted installation.
1
2
3
Connect the power adapter to the port on the
back of the charging station.
1
Connect the power adapter to the port on the
back of the charging station.
Place the charging station on a hard and level
floor.
2
Drill 2 holes and insert the drywall anchors (if
needed) at least 3.25 ft (1 m) from the floor
and near enough to easily reach a power
outlet.
Separate the extension pipe and nozzle from
the product body before charging or storing
the appliance.
• Before drilling, make sure that there are no
pipes or electrical wires inside the wall at
the desired location.
• For drywall anchor: use 1/4″ (6.5 mm) drill
bit
• For concrete or wall stud: use 1/8″ (3 mm)
drill bit
• If screwing into drywall, use the drywall
anchors.
4
Plug the power cord into the power outlet.
CAUTION
• Leaving the appliance on a level floor for a long
time with the extension pipe and nozzle
attached may damage the appliance.
3.25 ft
3
4
Attach the charging station to the wall with
the wall anchoring screws.
Plug the power cord into the power outlet.
us_main.book.book Page 15 Tuesday, March 31, 2020 5:28 PM
INSTALLATION 15
Assembling the Appliance
Follow these steps to safely assemble the
appliance.
Storing in the Accessory Bag
If the accessory bag is included in the model you
purchased, you can store the tool in the accessory
bag.
1
Firmly attach the extension pipe c, nozzle d,
or tool onto the product body a.
CAUTION
• To detach the extension pipe, press the
extension pipe release button b.
• Do not store the product body or battery in the
accessory bag. If the appliance or battery are
damaged, it could cause an explosion or fire.
• Do not throw or drop the accessory bag
containing accessories. It may damage the
appliance or cause personal injury.
NOTE
• Do not use the accessory bag for purposes other
than for storage of nozzles or tools.
2
Put the product body on the charging station.
• See Charging the Battery for instructions
on installing and charging the battery.
Storing the Accessories
Storing the Tools
Store the frequently used tools such as the
combination tool, crevice tool and cleaning brush
at the bottom of the charging station.
• Slide the cleaning brush up into the tool holder.
• Slide the combination tool over the cleaning
brush and onto the tool holder.
• To remove a tool, press the release button at the
front of the tool.
us_main.book.book Page 16 Tuesday, March 31, 2020 5:28 PM
16 OPERATION
OPERATION
• Do not use tools to clean a TV, monitor or LCD
display as they may scratch these surfaces.
Getting Started
Before Using the Appliance
• Make sure that the exhaust filter and pre-filter
are properly assembled before using the
appliance.
Assembling Attachments
Nozzles and tools can be attached to either the
product body or the end of the extension pipe.
• Close the dust bin cover properly before using
the appliance. If the dust bin cover is left open,
the suction strength may deteriorate and affect
the cleaning performance.
CAUTION
• Running the appliance for a long period of time
with a tool connected may cause the motor to
overheat.
• This appliance has a built-in safety device to
prevent overheating. If the appliance becomes
overheated after extended use, it may
automatically turn off. If this occurs, leave the
appliance in a cool, well-ventilated area for
about an hour before turning on the power
again.
• This appliance has a built-in safety device to
prevent overheating. If the appliance becomes
overheated after extended use, it may
automatically turn off. If this occurs, leave the
appliance in a cool, well-ventilated area for
about an hour before turning on the power
again.
• Make sure to remove any foreign object such as
a sock or stocking before using the appliance.
Any foreign object on the inlet port or extension
pipe will prevent the appliance from functioning
properly.
• Do not use the Kompressor lever while the
appliance is running. Doing so may cause
product damage.
• Environmental conditions such as temperature
and humidity may cause static electricity to
accumulate on the appliance. Please contact LG
Electronics customer information center if the
problem persists.
1
Insert the fully charged battery a into the
cavity at the bottom of the handle on the
product body.
• Please use the product at normal room
temperatures as the battery runtime may
deteriorate severely if used at temperatures
lower than 41 °F (5°C) or higher than 100 °F
(38°C) for an extended period of time.
• Do not use the appliance to suck up oils or any
liquids, including water.
2
Attach the nozzles, tools, or extension pipe by
sliding them onto the inlet b on the body
until they click into place. The nozzles and
tools can also be attached to the end of the
extension pipe b.
• Support the bottom of the appliance when
cleaning an elevated surface.
• Store the appliance in the charging station or
place it flat on the floor when not in use. Leaning
the appliance against a wall or chair can result in
product damage or personal injury if the
appliance falls.
• Detach the accessories by pressing the
release button c.
• To avoid scratches on polished floors, keep the
brushes of the nozzles and tools free from grit,
sand, or abrasive objects.
• Refer to the Specifications section for battery
runtime details.
• The battery runtime is dependent on the surface
type and the suction power.
• Follow manufacturer’s recommendations when
cleaning flooring, carpets, and rugs.
us_main.book.book Page 17 Tuesday, March 31, 2020 5:28 PM
OPERATION 17
3
Adjust the extension pipe by pressing the
length adjustment button d on the back of
the pipe and sliding until it clicks into place at
the desired length.
Display
The handle of the appliance displays indicators for
clogged objects, filter cleaning alerts, appliance
connection status, and the remaining battery
charge.
• The extension pipe extends in four steps.
a Clogged Objects Indicator
4
Press the Power button to activate the
Normal mode.
• This indicator lights up when the interior of
the product body, extension pipe, inlets,
nozzle, exhaust filter, pre-filter, or cyclonic
mesh filter is clogged with foreign objects.
• To turn off the appliance, press the Power
button again.
• If clogging persists, the motor will cycle and
the appliance will shut off. Remove the
foreign objects and clean the exhaust filter,
pre-filter and cyclonic mesh filter following
the steps in the Removing Foreign Objects
section.
Adjusting the Suction Power
Adjust the suction power using the suction power
adjustment button on the handle.
b Filter Cleaning Cycle Alarm Indicator
• This indicator lights up when the appliance is
used for a certain period of time. Clean the
exhaust filter, pre-filter and cyclonic mesh
filter if necessary.
c Wi-Fi Indicator
• This indicator blinks when the appliance is
connecting to the LG ThinQ application or
home Wi-Fi network, and the indicator lights
up when the connection is complete.
a Power Button
• Press the Power button to turn the appliance
on or off.
• Press the Power button to activate Normal
d Battery Level Indicator
mode.
• The remaining battery level is displayed in 3
stages according to the remaining battery
power.
b Suction Power Up (+) Button / Turbo Mode
• Press the + button to increase the suction
power. (Normal~Power~Turbo)
• The battery level indicator blinks when the
battery needs to be charged.
• Press and hold the + button for more than 3
seconds to activate Turbo mode from Power
mode.
• As the product is charging, bars light up on
the battery level indicator to indicate the level
of charge.
c Suction Power Down (-) Button / Wi-Fi Mode
• Once the battery is fully recharged, 3 bars will
remain lighted on the battery level indicator.
• Press the - button to decrease the suction
power. (Turbo~Power~Normal)
• Press and hold the - button for 3 seconds to
activate Wi-Fi and connect the appliance in
the LG ThinQ application.
us_main.book.book Page 18 Tuesday, March 31, 2020 5:28 PM
18 OPERATION
Charging the Battery
Before Charging the Battery
• Make sure that the adapter is connected to both
the charging station and the power outlet.
WARNING
• Make sure to securely fit the product body onto
the charging station. If the appliance falls off the
charging station, it could cause injuries, property
damage or product damage.
• Fully charging a single battery usually takes
about 4 hours. It will take twice as long to charge
both the main and auxiliary batteries.
Charging the Auxiliary Battery
An auxiliary battery can be stored and charged in
the base of the charging station.
• The battery will not be charged if the indoor
temperature is below 41 °F (5°C). Only charge
the battery when indoor temperatures are
between 41 °F (5°C) and 100 °F (38 °C).
CAUTION
• The battery will eventually need to be replaced.
Due to the battery characteristics, runtime is
shortened after using the appliance repeatedly
for an extended period.
• Keep fingers away from pinch points when
assembling or disassembling the battery from
the product body or the charging station to
avoid personal injury.
• The last bar on the battery indicator begins to
blink when the battery needs to be recharged.
Use the appliance with a fully charged battery.
1
Remove the discharged battery from the
product body by pressing the battery release
button on either side of the battery and
pulling.
• If the main battery is charging on the charging
station, the auxiliary battery will only start
charging once the main battery is fully charged.
• To maintain battery life on dual-battery models,
swap the positions of the two batteries
periodically, between the main body and the
auxiliary charging station.
Charging the Product Body
Storing the appliance on the charging station
automatically recharges the battery.
2
Insert the discharged battery into the
auxiliary charging station.
1
2
Press the Power button to turn the appliance
off.
• The battery will only fit into the cavity if
aligned properly.
Put the product body onto the charging
station by aligning it to the hook a of the
charging station.
• The auxiliary charging indicator blinks while
recharging is in progress.
• The auxiliary charging indicator lights up
when charging is complete.
• The battery level indicator starts to blink
and begins charging the battery.
• If you don't hear a beep, reload the
appliance on the charging station.
us_main.book.book Page 19 Tuesday, March 31, 2020 5:28 PM
OPERATION 19
• Use it with the Turbo mode to clean pet hair out
of furniture, mats, or tight areas like corners.
Using the Nozzles and Tools
Some accessories are only available on some
models.
Specialized attachments can help you clean more
effectively. Tools and nozzles can be attached to
the product body or the extension pipe.
• Adjust the suction power if the inlet gets stuck
on the floor, carpet, or bedding.
• Each Power Drive Nozzle (Power Carpet or Power
Punch) is equipped with a motor and may make
a sound when operating.
Combination Tool
Can be used in either crevice mode or brush mode
for cleaning corners or small gaps where dust and
dirt gather.
CAUTION
• Do not use Power Floor Nozzle or Power Carpet
Nozzle on PVC or polyurethane mats for infants
and children. The mat may stick to the nozzle,
making it difficult to operate, causing damage to
the mat or static electricity on the appliance.
Clean mats using the crevice tool.
• Crevice Mode
Use the tool in the crevice mode to clean flat
surfaces such as sofas or mattresses.
Power Carpet Nozzle
Use this nozzle to clean carpets or rugs.
• Brush Mode
• If used on hard flooring, this nozzle will be noisy.
Use the tool in the brush mode to clean delicate
surfaces such as frames or furniture.
- To convert modes, press the adjustment
button a and push forward.
Power Punch Nozzle
This nozzle lets you clean sheets and bedding
more effectively. It removes dust in bedding using
strong suction and a punching motion.
• Lower the suction level when vacuuming
bedding such as duvet covers to avoid the thin
fabric getting sucked into the nozzle.
Hard Dirt Tool
Firm bristles remove solidified dirt from hard
surfaces. Clean up hair or foreign objects that are
entangled in carpets or rugs.
Crevice Tool
Use this tool to remove dust from corners or
narrow spaces.
• Use it for areas with static electricity such as
mats.
us_main.book.book Page 20 Tuesday, March 31, 2020 5:28 PM
20 OPERATION
Mattress Tool
Use this tool to clean up dust and foreign objects
from mattresses, delicate fabrics, and upholstery.
Multi-angle Tool
This tool has a soft brush that can be adjusted to a
variety of angles, making it especially useful for
cleaning vehicle consoles or the tops of furniture.
Flexible Crevice Tool
Flexible Hose Extension
Connect this flexible, extendable hose between the
product body and the tools to clean hard to reach
areas.
This tool is flexible and its length can be adjusted,
making it especially useful for cleaning inside
vehicles or in narrow spaces under and behind
furniture where an angled tool is needed.
• The flexible hose extension cannot be used with
the Power Drive Nozzle.
Using the Brush
To convert the tool from crevice to brush mode,
press in on the sides of the brush head a and pull
the brush down.
Using the Kompressor Lever
Use the Kompressor lever to compress hair and
fibers inside the dust bin after vacuuming and
before emptying the dust bin.
• To convert back to the crevice mode, press in on
the brush release button b and slide the brush
up.
• The vacuum must be turned off before using the
Kompressor lever.
• Compressing the dust clears it off the interior
walls of the dust bin and allows you to vacuum
for longer periods before emptying the dust bin.
It also makes cleaning the dust bin easier and
less messy.
Adjusting the Length
• The dust bin must be at least half full for the
compression plate to be effective.
To adjust the length of the tool, press and hold the
release button c on the side of the tool. Pull or
push on the brush head d to extend or retract the
extension tube.
• Press the Kompressor lever down several times
to compress the dust and clean off the interior
walls of the dust bin.
us_main.book.book Page 21 Tuesday, March 31, 2020 5:28 PM
SMART FUNCTIONS 21
SMART FUNCTIONS
Before Using LG ThinQ Application
Using LG ThinQ Application
This feature is only available on models with the b
1
2
3
Use a smartphone to check the strength of
the wireless router (Wi-Fi network) near the
appliance.
or a logo.
The LG ThinQ application allows you to
communicate with the appliance using a
smartphone.
• If the appliance is too far from the router,
the signal becomes weak. It may take a long
time to register or fail to install the
application.
LG ThinQ Application Features
• Cleaning History
Turn off the Mobile data or Cellular Data on
your smartphone.
- Shows the cleaning history, such as monthly
cleaning time, cleaning frequency, and
cleaning mode, etc.
NOTE
• Assembled suction tool is displayed on the
screen during cleaning.
• A notification is displayed on the screen if the
pre-filter and the exhaust filter need cleaning.
Connect your smartphone to the wireless
router.
• Filter Cleaning Cycle Alarm
- After using the appliance for a centain period
of time, a notification is displayed on the
screen of your smartphone. Clean the exhaust
filter or pre-filter, if necessary.
• Cleaning Mode
NOTE
- The cleaning mode you are using is displayed
on the screen of your smartphone.
• To verify the Wi-Fi connection, check that the f
icon on the control panel is lit.
• Filter Cleaning Guide
- Guide to cleaning the filters.
• Smart Diagnosis™
• The appliance supports 2.4 GHz Wi-Fi networks
only. To check your network frequency, contact
your Internet service provider or refer to your
wireless router manual.
- This function provides useful information for
diagnosing and solving issues with the
appliance based on the pattern of use.
• LG ThinQ is not responsible for any network
connection problems or any faults, malfunctions,
or errors caused by network connection.
NOTE
• The surrounding wireless environment can
• If you change your wireless router, Internet
service provider, or password, delete the
connected appliance from the LG ThinQ
application and connect it again.
make the wireless network service run slowly.
• If the appliance is having trouble connecting to
the Wi-Fi network, it may be too far from the
router. Purchase a Wi-Fi repeater (range
• This information is current at the time of
publication. The application is subject to change
for product improvement purposes without
notice to users.
extender) to improve the Wi-Fi signal strength.
• The network connection may not work properly
depending on the Internet service provider.
• The Wi-Fi may not connect or the connection
may be interrupted because of the home
network environment.
us_main.book.book Page 22 Tuesday, March 31, 2020 5:28 PM
22 SMART FUNCTIONS
NOTE
NOTE
• If the appliance cannot be connected due to
problems with the wireless signal transmission,
unplug the appliance and wait about a minute
before trying again.
• The usage history will be reset if you delete a
connected appliance in LG ThinQ.
• If the Wi-Fi signal is weak, the appliance may be
temporarily disconnected to the application.
When the Wi-Fi signal moves to the normal
position, the appliance is connected to the
application again.
• If the firewall on your wireless router is enabled,
disable the firewall or add an exception to it.
• The wireless network name (SSID) should be a
combination of English letters and numbers. (Do
not use special characters.)
• Smartphone user interface (UI) may vary
depending on the mobile operating system (OS)
and the manufacturer.
Turning Wi-Fi On/Off on the
Appliance
• If the security protocol of the router is set to
WEP, network setup may fail. Change the
security protocol (WPA2 is recommended), and
connect the product again.
Disconnecting from Wi-Fi
To save energy, turn off the Wi-Fi function by
pressing the Wi-Fi button for 3 seconds while the
appliance is charging on the charging station.
Reconnecting to Wi-Fi
Follow the steps below on the appliance.
Installing the LG ThinQ Application
Search for the LG ThinQ application from the
Google Play Store or Apple App Store on a
smartphone. Follow instructions to download and
install the application.
1
2
Press and hold the Wi-Fi button for 3 seconds
until the f icon blinks in the display.
Press the Wi-Fi button for 3 seconds again.
• After the icon turns off, wait for a while and
turn it on again.
Connecting the Appliance to LG
ThinQ
• The time before the icon turns on may vary
depending on the network environment.
Wi-Fi Indicator f Status
Indicator
Description
Status
Wireless LAN Module Specifications
Model
LCW-007
Blinking
ON
The appliance is connecting.
Frequency
Range
2412 - 2462 MHz
The appliance has finished
connecting.
The appliance is connected to Wi-Fi.
Output Power < 30 dBm
(Max)
OFF
The appliance has been
disconnected.
FCC Notice
The following notice covers the transmitter
module contained in this product.
Connecting the Appliance Initially
Select your appliance on menu by pressing the
Add a Product (+) button. Follow instructions in
the LG ThinQ to connect your appliance.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
Connecting Additional Users
Remove the appliance from the charging station.
Follow the instructions under Connecting the
Appliance Initially.
us_main.book.book Page 23 Tuesday, March 31, 2020 5:28 PM
SMART FUNCTIONS 23
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Supplier’s Declaration of
Conformity
Trade Name
Responsible Party
Address
LG
LG Electronics USA, Inc.
1000 Sylvan Ave Englewood
Cliffs, NJ 07632
• Reorient or relocate the receiving antenna.
Email
• Increase the separation between the equipment
and the receiver.
Open Source Software Notice
Information
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained
in this product, please visit http://
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
opensource.lge.com. In addition to the source
code, all referred license terms, warranty
disclaimers and copyright notices are available for
download.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
and
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email
request to [email protected]. This offer is valid
for a period of three years after our last shipment
of this product. This offer is valid to anyone in
receipt of this information.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-
located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated
with a minimum distance of 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
us_main.book.book Page 24 Tuesday, March 31, 2020 5:28 PM
24 SMART FUNCTIONS
Smart Diagnosis™ Function
Use this feature to help you diagnose and solve
problems with your appliance.
NOTE
• For reasons not attributable to LGE’s negligence,
the service may not operate due to external
factors such as, but not limited to, Wi-Fi
unavailability, Wi-Fi disconnection, local app
store policy, or app unavailability.
• The feature may be subject to change without
prior notice and may have a different form
depending on where you are located.
Using LG ThinQ to Diagnose Issues
If you experience a problem with your Wi-Fi
equipped appliance, it can transmit
troubleshooting data to a smartphone using the
LG ThinQ application.
• Launch the LG ThinQ application and select the
Smart Diagnosis™ feature in the menu. Follow
the instructions provided in the LG ThinQ
application.
1
2
Put the product body on the charging station.
Launch the LG ThinQ application on your
smartphone.
3
4
Select the connected product on your screen.
Press the menu button on the upper right
corner of the screen and select the Smart
Diagnosis feature.
5
6
Press the Start button to begin diagnosing
the appliance.
Press the Finish button to complete the
diagnosis process.
us_main.book.book Page 25 Tuesday, March 31, 2020 5:28 PM
MAINTENANCE 25
MAINTENANCE
• If the inlets are not completely blocked, the
Cleaning the Appliance
foreign objects clogging alarm indicator may not
light up.
Before Cleaning the Appliance
• If the sound of the appliance becomes loud or
the cleaning performance is poor, check for
foreign objects.
To maintain the optimum suction power, the
cyclonic mesh filter, the exhaust filter and the pre-
filter should be cleaned regularly and washed
under running water at least once a month.
• Turn off the power before cleaning the
appliance.
• The frequency of cleaning varies depending on
the usage environment and usage time. In a
dusty environment, clean frequently.
WARNING
• Never wash the Power Drive Nozzle, rotating
brush or product body with water. Water could
reach the motor and cause electric shock or fire.
• Do not allow foreign objects to enter the motor.
Doing so may cause electric shock, fire or
product damage.
• Do not insert fingers or sharp objects into the
motor. Doing so could cause product damage,
personal injury or electric shock.
Cleaning the Dust Bin
Empty and clean the dust bin after every use.
CAUTION
• If the dust bin is completely full of dust or the
filter is clogged, the suction power may be
reduced.
• Do not apply force or allow impacts to the
cyclonic mesh filter. Doing so could deform the
filter, compromise product performance, or
cause the product to malfunction.
CAUTION
• If the Kompressor lever does not return to the
top, remove the cyclonic mesh filter from the
dust bin and clean it. A clogged or dirty filter may
cause poor product performance.
• Do not use the appliance without the cyclonic
mesh filter installed. Doing so could damage the
appliance.
1
2
Remove the battery from the product body
before cleaning the dust bin.
Removing Foreign Objects
If the appliance is clogged with foreign objects, the
suction power changes, the motor cycles
repeatedly, and the foreign objects clogging alarm
icon blinks.
Push down the Kompressor lever a several
times to collect and compact the dust from
the outside of the cyclonic mesh filter and the
interior walls of the dust bin.
If clogging persists, the appliance will turn off
automatically to prevent damage. Separate the
battery from the product body and remove the
foreign objects before resuming use of the
appliance.
• Foreign objects which become lodged in the
cyclonic mesh filter may be difficult to
dislodge with the Kompressor lever.
Remove the cyclonic mesh filter and use the
provided cleaning brush to clean it.
• Check the inside of the product body, above the
Kompressor working plate, the extension pipe,
inlets, exhaust filter, pre-filter and cyclonic mesh
filter for foreign objects.
us_main.book.book Page 26 Tuesday, March 31, 2020 5:28 PM
26 MAINTENANCE
5
Wash the cyclonic mesh filter under running
water.
• To avoid odor and the malfunction of the
motor, allow the cyclonic mesh filter to dry
completely in a well-ventilated area out of
direct sunlight for at least 24 hours before
reassembling.
3
Press the dust bin cover release button b to
open the dust bin cover. Shake the dust bin to
empty it.
• Be careful as dust or foreign objects may
spill out when opening the dust bin. Empty
the dust bin into a wastebasket or where
dust and foreign objects can be easily
removed.
6
Use the combination tool e to clean out dust
or foreign objects inside the dust bin.
• The dust bin can be wrapped in a plastic bag
to contain the dust when emptying the dust
bin.
• Do not wash the product body or motor
with water.
7
Turn the product body over and lift the
Kompressor lever f up to clean the inside of
the working plate with the provided cleaning
brush.
WARNING
• If the Kompressor lever does not slide down
smoothly, foreign objects may be trapped
between the dust bin and the cyclonic mesh
filter. Clean the dust bin and cyclonic mesh filter
to avoid product damage.
• Do not push the Kompressor lever down
hard. The working plate may be damaged.
• Do not force the Kompressor lever down if
foreign objects are caught around the working
plate of the Kompressor system. Doing so may
cause product damage.
4
Insert the crevice tool d into the cyclonic
mesh filter c and turn it counterclockwise to
remove the filter.
8
9
Turn the product body over again and shake it
while pressing down the lever to remove the
dust.
Wrap the provided cleaning brush with a wet
paper towel, tucked into the slots g on the
handle.
us_main.book.book Page 27 Tuesday, March 31, 2020 5:28 PM
MAINTENANCE 27
10 Turn the product body over, lift the
Kompressor lever h up, and clean the inside
of the working plate with the towel-wrapped
brush handle.
4
Use the combination tool d to clean any dust
off the motor.
• Do not wash the motor with water.
5
Clean filters by brushing the dust off and
wash them in running water at least once a
month.
Cleaning the Filters
Clean the exhaust filter and the pre-filter when the
filter cleaning icon K lights up.
• To avoid odor and the malfunction of the
motor, allow the exhaust filter to dry
completely in a well-ventilated area out of
direct sunlight for at least 24 hours before
reassembling.
• Clean the filters more frequently if the appliance
is used regularly or in areas with a lot of dust.
CAUTION
• Do not use the appliance without the exhaust
filter and pre-filter installed. Doing so could
result in product damage.
1
2
Remove the battery from the product body.
Rotate the exhaust filter a to the unlocked
position b to separate it from the product
body.
6
Insert the dried pre-filter and rotate the
exhaust filter to the locked position e to
reassemble it on the product body.
3
Lift out the pre-filter c from the product
body.
us_main.book.book Page 28 Tuesday, March 31, 2020 5:28 PM
28 MAINTENANCE
Cleaning the Nozzle
Clean the nozzle and rotating brush regularly.
CAUTION
• Always separate the nozzle from the product
body or remove the battery before cleaning. If
the nozzle starts to operate during cleaning, it
could cause an injury.
5
Use a damp towel or cloth to remove any
remaining foreign objects and dust from the
brush and the bottom of the nozzle.
• Keep fingers away from pinch points when
assembling the nozzle on the appliance or the
rotating brush on the nozzle.
• Carefully use a tweezers to remove foreign
objects from the nozzle rollers.
• Do not use the rotating brush as a wet mop. It
may cause product damage.
• Do not rinse or submerge the rotating
brush or nozzle in water.
• Wrap the handle of the cleaning brush with
a wet towel or cloth and use it to clean the
rotating brush and nozzle.
Cleaning the Power Carpet Nozzle
Clean the brush and roller heads before each use.
• If the brush contains foreign objects, the brush
may not spin or a noise may occur during
operation.
1
Press the nozzle release button a to remove
the nozzle from the extension pipe or product
body.
6
Slide the brush back into the nozzle and
rotate the cover back into place. Turn the
cover lock clockwise to lock the cover.
2
Turn the nozzle upside down and rotate the
cover lock slot b counterclockwise.
Cleaning the Power Punch Nozzle
1
Press the nozzle release button to remove the
nozzle from the extension pipe or product
body and turn the nozzle upside down.
2
Attach the crevice tool to the product body
and use the vacuum to remove foreign
objects and dust from the bottom of the
nozzle.
• Use a damp towel or cloth to remove any
remaining foreign objects and dust from
the bottom of the nozzle. After cleaning,
wipe the nozzle dry.
3
4
Pull the brush cover forward and pull the
brush out.
• Do not rinse or submerge the nozzle in
water.
Attach the crevice tool to the product body
and use the vacuum to remove foreign
objects and dust from the brush and the
bottom of the nozzle.
us_main.book.book Page 29 Tuesday, March 31, 2020 5:28 PM
TROUBLESHOOTING 29
TROUBLESHOOTING
Before Calling for Service
Operation
Problem
Possible Cause & Solution
The appliance does
not operate.
Battery is fully discharged.
• Charge the battery.
Appliance is turned off.
• Press the Power button to turn on the appliance.
Suction power is too Dust bin is full of dust.
weak.
• Empty the dust bin.
Filters are clogged.
• Clean the pre-filter and the exhaust filter.
Inlet is clogged.
• Remove any foreign objects from inside the product body or the extension pipe.
Foreign object is on rotating brush, or in inlet port.
• Remove any foreign objects (thread, hair) from the rotating brush or the inlet port.
The product body
does not appear to
be charging.
Power adapter is not connected to the charging station.
• Plug the adapter firmly into the charging station.
Power cord is unplugged.
• Plug the power cord securely into the charging station.
Foreign object is on the charging terminals.
• Remove dirt or foreign objects from the charging terminals with a dry cloth.
Hot air is coming
from the product
body.
Motor is cooling.
• If the appliance is running normally, the hot air is a result of the motor cooling and is not a
sign of malfunction.
A strange odor is
coming from the
appliance.
Appliance was purchased within the last 3 months.
• The cleaner may emit a smell of rubber for about 3 months after purchase.
Dust bin is full of dust.
• The dust in the bin may cause some odor. Empty the bin and clean it.
Foreign object is on the filter.
• The filter may emit an odor if it has not been cleaned for some time. Clean the pre-filter
and exhaust filter regularly.
Pre-filter was installed while damp or wet.
• Wash the pre-filter with running water. To avoid odor, allow the pre-filter to dry completely
in a well-ventilated area out of direct sunlight for at least 24 hours before reassembling.
Exhaust filter was installed while damp or wet.
• Wash the exhaust filter with running water. To avoid odor, allow the exhaust filter to dry
completely in a well-ventilated area out of direct sunlight for at least 24 hours before
reassembling.
The appliance makes Vacuum cleaner is running in Turbo mode.
too much noise.
• The motor may be louder at the higher suction power settings. This is normal.
us_main.book.book Page 30 Tuesday, March 31, 2020 5:28 PM
30 TROUBLESHOOTING
Problem
Possible Cause & Solution
The appliance turns
off unexpectedly or
by itself after the
motor speed
Battery is not fully charged.
• The battery must be fully charged before cleaning. If the problem persists when the
battery is fully charged and the pipes and attachments are clear from obstructions, contact
an LG customer information center for service.
fluctuates
repeatedly.
Foreign object is in the product body, extension pipe, inlet port or nozzle.
• Remove any foreign objects from the product body, extension pipe, inlet port or nozzle.
Filters are clogged.
• Clean the pre-filter and the exhaust filter.
The rotating brush
does not rotate.
Brush is improperly installed.
• Remove the brush, clean it if necessary and attach it again.
Foreign object is on rotating brush.
• Remove any foreign objects from the rotating brush.
us_main.book.book Page 31 Tuesday, March 31, 2020 5:28 PM
LIMITED WARRANTY 31
LIMITED WARRANTY
USA
TERMS AND CONDITIONS
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES
YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU
CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE
SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
LG Electronics Inc. will repair or replace your product, at LG’s option, if it proves to be defective in material
or workmanship under personal household use, during the warranty period set forth below, effective from
the date of original consumer purchase of the product. This limited warranty is good only to the original
purchaser of the product and effective only when used in U.S.A. and Canada.
* Manufacturing Locations: LG Electronics. Changwon Factory2 84, Wanam-ro, Seongsan-gu, Changwon-si,
Gyeongsangnam-do, 642-713, KOREA
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
1 Year
Any part of the Cleaner which fails due to a defect in materials or
workmanship. During this full 1 Year warranty, LG will also provide, free
of charge, all labor and shop service to replace the defective part.
Inverter motor: 10 year warranty (Suction motor)
From the date of the original
purchase
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN
DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. LG WILL NOT BE LIABLE FOR ANY
CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES
OR PROFITS, IN CONNECTION WITH THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON
HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
This warranty covers only defects in material and workmanship.
LGE will NOT pay for:
1) Expendable items that can wear out, including, but not limited to, filters and belts.
2) A service technician to instruct the user in correct product assembly, operation or maintenance.
3) A service technician to clean or maintain this product.
4) Damage to or failure of this product if it is not assembled, operated or maintained according to all
instructions supplied with this product.
5) Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its
intended purpose.
6) Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils
other than those recommended in all instructions supplied with this product.
7) Damage to or failure of parts or systems resulting from unauthorized modifications made to this
product.
This warranty is extended to the original purchaser for products purchased for home use within the U.S.A.
In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. To know what your legal rights are, consult your local or
state consumer affairs or your state’s Attorney General.
us_main.book.book Page 32 Tuesday, March 31, 2020 5:28 PM
32 LIMITED WARRANTY
CUSTOMER ASSISTANCE INFORMATION:
To Prove Warranty Coverage
Retain your Sales Receipt to prove date of purchase.
A copy of your Sales Receipt must be submitted at the time warranty
service is provided.
To Obtain Nearest Authorized
Call 1-800-243-0000 (Phone answered 24 hours - 365 days a year) and
Service Center or Sales Dealer, or choose the appropriate prompt from the menu; or visit our website at:
to Obtain Product, Customer, or
Service Assistance
(In Canada- Call 1-888-542-2623, website http://ca.lgservice.com)
PROCEDURE FOR RESOLVING DISPUTES:
ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED
WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND
NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH
WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION.
Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc., its
parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries,
predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include
any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute,
regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or
relating in any way to the sale, condition or performance of the product or this Limited Warranty.
Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must first notify
LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LG at LG
Electronics, USA, Inc. Attn: Legal Department- Arbitration 1000 Sylvan Ave, Englewood Cliffs 07632. You
and LG agree to engage in good faith discussions in an attempt to amicably resolve your claim. The notice
must provide your name, address, and telephone number; identify the product that is the subject of the
claim; and describe the nature of the claim and the relief being sought. If you and LG are unable to resolve
the dispute within 30 days, either party may proceed to file a claim for arbitration.
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during
the 30 day period after sending written notice to LG, you and LG agree to resolve any claims between us
only by binding arbitration on an individual basis, unless you opt out as provided below. Any dispute
between you and LG shall not be combined or consolidated with a dispute involving any other person’s or
entity’s product or claim. More specifically, without limitation of the foregoing, any dispute between you
and LG shall not under any circumstances proceed as part of a class or representative action. Instead of
arbitration, either party may bring an individual action in small claims court, but that small claims court
action may not be brought on a class or representative basis.
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written
demand for arbitration. The arbitration will be administered by the American Arbitration Association
(“AAA”) and will be conducted before a single arbitrator under the AAA’s Consumer Arbitration Rules that
are in effect at the time the arbitration is initiated (referred to as the “AAA Rules”) and under the
copy of your written demand for arbitration, as well as a copy of this provision, to the AAA in the manner
described in the AAA Rules. You must also send a copy of your written demand to LG at LG Electronics,
USA, Inc. Attn: Legal Department- Arbitration 1000 Sylvan Avenue Englewood Cliffs, NJ 07632. If there is a
conflict between the AAA Rules and the rules set forth in this section, the rules set forth in this section will
govern. This arbitration provision is governed by the Federal Arbitration Act. Judgment may be entered on
the arbitrator’s award in any court of competent jurisdiction. All issues are for the arbitrator to decide,
except that issues relating to the scope and enforceability of the arbitration provision and to the
arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this
provision.
Governing Law. The law of the state of your residence shall govern this Limited Warranty and any
disputes between us except to the extent that such law is preempted by or inconsistent with applicable
federal law.
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand
for arbitration, LG will promptly pay all arbitration filing fees to the AAA unless you seek more than $25,000
in damages, in which case the payment of these fees will be governed by the AAA Rules. Except as
us_main.book.book Page 33 Tuesday, March 31, 2020 5:28 PM
LIMITED WARRANTY 33
otherwise provided for herein, LG will pay all AAA filing, administration and arbitrator fees for any
arbitration initiated in accordance with the AAA Rules and this arbitration provision. If you prevail in the
arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by considering
factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the
foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator
can award them to the same extent that a court would. If the arbitrator finds either the substance of your
claim or the relief sought in the demand is frivolous or brought for an improper purpose (as measured by
the standards set forth in Federal Rule of Civil Procedure 11(b)), then the payment of all arbitration fees will
be governed by the AAA Rules. In such a situation, you agree to reimburse LG for all monies previously
disbursed by it that are otherwise your obligation to pay under the AAA Rules. Except as otherwise
provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if LG prevails
in the arbitration.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration
conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic
hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the
right to a hearing will be determined by the AAA Rules. Any in-person arbitration hearings will be held at a
location within the federal judicial district in which you reside unless we both agree to another location or
we agree to a telephonic arbitration.
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can
require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no
later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by
either: (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out” or (ii) calling 1-
800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;
(b) the date on which the product was purchased; (c) the product model name or model number; and (d)
the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https://
Number”).
You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail
or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.
Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any
way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and
do not opt out, then you accept all terms and conditions of the arbitration provision described above.
us_main.book.book Page 34 Tuesday, March 31, 2020 5:28 PM
34 APPENDIX
APPENDIX
U.S. Patent Protection
This product is covered by one or more of the following patents in the U.S.
Patents
US10342404; US10314453; US10194779; US10229651; US10229650; US10405717; US10478036;
US10433688; US10561291; US10542860; US10531777; US10492653
OTHER PATENTS PENDING
us_main.book.book Page 35 Tuesday, March 31, 2020 5:28 PM
Memo 35
us_main.book.book Page 1 Tuesday, March 31, 2020 5:28 PM
|