LG 75XE3C User Manual

OWNER’S MANUAL  
LG Digital  
Signage  
(MONITOR SIGNAGE)  
Please read this manual carefully before operating your set and retain it  
for future reference.  
55XE3C  
75XE3C  
Copyright © 2018 LG Electronics Inc. All Rights Reserved.  
3
WARNING - This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may  
cause radio interference.  
SAFETY PRECAUTION  
The Safety Precautions are intended to prevent unexpected danger or harm by helping the user to use the product  
safely and for its intended purpose.  
WARNING  
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.  
CAUTION  
If you ignore the caution message, you may be slightly injured or the product may be damaged.  
Precautions When Installing the Product  
WARNING  
Failure to observe these warnings may result in serious injury or death.  
Do not place the product close to heat sources such as fires and stoves.  
- There is a risk of fire.  
Do not hang from or climb on the product.  
- You may fall and cause injury.  
Do not install the product in a damp or dusty area.  
- This may create a fire hazard or result in electric shock or damage to the product.  
If the product has been dropped or its case is damaged, turn off the power and unplug the power cord from the  
power outlet.  
- Otherwise, the product may cause fire or electric shock. Contact the service center.  
Do not drop the product, subject it to shock, or throw any objects at the product screen.  
- This may result in damage to the screen, malfunction of the product, or personal injury.  
When there is smoke or a strange smell or sound emitting from the product, disconnect the power cord and then  
contact the service center.  
- Otherwise, the product may cause fire or electric shock.  
Do not leave the power or signal cable, etc. in walkways.  
- If you step on or fall over the cable, it may cause fire, electric shock, product damage or personal injury.  
Keep the anti-moisture material or vinyl film used for packaging the product out of reach of children.  
- If swallowed by mistake, force it to be vomited and visit the nearest hospital as a matter of urgency.  
4
Be careful when installing the product where it is likely to get wet, such as in a bathroom or other locations exposed  
to rain or water.  
- This may cause fire, electric shock or product malfunction.  
Do not insert pieces of metal, such as coins, hairpins and metal debris, or flammable materials, such as paper or  
matches, into the product.  
- Doing so may cause fire or result in electric shock. If foreign materials fall into the product, disconnect the power  
cord and then contact the service center.  
Do not install the product by yourself. The product should be installed by a professional installation technician  
specified by the retail store.  
- Product installation by a non-professional installation technician is very dangerous and may cause personal injury.  
Do not install the product onto a wall that is close to sources of oil or oil mist.  
- Otherwise, it may result in damage to the product and cause the product to fall.  
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
Set to [Screen OFF & Backlight (Outdoor Mode)] when installing outdoors.  
- Enable the [Outdoor Mode] to reduce the risk of the internal humidity and condensation.  
- When operating in below zero temperature, the enclosure may not work for up to one hour to raise the internal  
temperature of the enclosure.  
Ensure that the product is installed a certain distance (at least 100 mm) away from the wall for good ventilation.  
- Failure to do so may result in the deformation of the product or fire due to the increase in the internal temperature.  
When placing the product on a table or shelf, be careful not to place it on the edge.  
- The product may fall, causing personal injury or damage to the product. Make sure to use a table or stand that fits  
the product.  
Do not place the product close to sources of steam or oil, such as humidifiers and kitchen counters.  
- This may result in electric shock or fire.  
Make sure the air vents are not blocked by a tablecloth or curtain.  
- Failure to do so may result in the deformation of the product or fire due to the increase in the internal temperature.  
Do not install the product in an area with poor ventilation (e.g. on a bookshelf, in a closet, in separate outdoor  
structures), and avoid placing on cushions or carpets.  
- This could result in fire due to high internal temperature.  
Do not place the product on an unstable or vibrating surface such as a vibrating shelf or tilted surface.  
- The product may fall or flip over and cause injury.  
Do not install the product in a place with electromagnetic interference.  
In addition, do not install it in close proximity to hot objects, such as lights.  
If you install the product in unusual locations that do not meet the general conditions, this may cause serious damage  
to the product’s picture quality, life cycle or appearance. Please check with our service engineers before installing in  
such locations.  
Unusual locations: Locations where much fine dust or oil mist is generated, locations where chemical substances are  
used, locations where the temperature is too high or low and other locations where the product was not meant to be  
used.  
5
Precautions for the AC Adapter and Power  
WARNING  
Failure to observe these warnings may result in serious injury or death.  
If water or any foreign substance enters the product (TV, device, power cord or AC adapter), disconnect the power  
cord immediately and contact the service center.  
- Otherwise, the damage to the product may cause a fire or electric shock.  
Always connect the power cord to a grounded outlet.  
- Failure to do so may result in electric shock or personal injury.  
Do not touch the power cord or the signal cable in the event of thunder and lightning.  
- There is risk of electric shock.  
Do not touch the power plug or AC adapter with wet hands. If the pins of the plug are wet or dusty, wipe or dry them  
thoroughly before use.  
- Failure to do so may cause electric shock or fire.  
Insert the power plug securely so that it does not come loose. Do not use the product if the power outlet is loose.  
- A bad connection may cause a fire or electric shock.  
Make sure the power cord is fully inserted into the AC adapter.  
- If loose, the poor connection may cause a fire or electric shock.  
Do not insert a conductor such as a chopstick into the other side of the cord while the power cord is inserted into the  
wall outlet. Also, avoid touching the power plug immediately after pulling it out of the wall outlet.  
- This may cause electric shock.  
Be sure to use power cords and AC adapters provided or approved by LG Electronics, Inc.  
- The use of non-approved products may cause fire or electric shock.  
Use the product at the rated voltage only.  
- Failure to do so may result in damage to the product or electric shock.  
Do not use with a multi-outlet shared with many devices. Use a dedicated multi-outlet with a ground terminal.  
- Otherwise, this may result in fire due to excessive heat.  
Disconnect the power cable when the product is not used for a long period of time.  
- Dust may accumulate, resulting in electrical short circuits, electric shock or fire due to overheating, combustion or  
insulation degradation.  
When unplugging the power cord, always pull it by the plug. Do not bend the power cord with excessive force.  
- A damaged cable may result in electric shock or fire.  
Be careful not to step on or place heavy objects (electronic appliances, clothing, etc.) on the power cord or AC  
adapter. Be careful not to damage the power cord or AC adapter with sharp objects.  
- Damaged power cords may cause a fire or electric shock.  
Never disassemble, repair or modify the power cord or AC adapter.  
- This may cause a fire or electric shock.  
To turn off the main power, remove the power cord, which should be positioned so it is easy to access for operation.  
If the product is connected to an AC wall outlet, it will not be disconnected from the AC power source even if you  
turn off the switch.  
Power consumption will be ‘0’ only when the power plug is unplugged.  
6
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
Do not remove the power cord when the product is in use.  
- Otherwise, the product may be damaged due to the sudden loss of power.  
Be sure to keep the outlet, AC adapter and pins of the power plug clean from dust, etc.  
- Failure to do so may cause fire.  
Do not turn the product on or off by plugging in or unplugging the power plug from the power outlet. (Do not use the  
power plug as a switch.)  
- This may cause an electric shock or product malfunction.  
Keep the power cord away from any heating devices.  
- The cord coating may melt and cause fire or electric shock.  
Precautions When Moving the Product  
WARNING  
Failure to observe these warnings may result in serious injury or death.  
Before moving the product, disconnect the power cord and all other cables connected.  
- Otherwise, this may result in electric shock or product damage.  
When carrying the product, make sure the screen faces forward and hold it firmly in both hands.  
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
Do not discard the delivery box with the original packaging.  
- Put the product in the box when carrying it.  
Lifting, moving or unpacking the product require at least two people due to the weight of the product.  
- Failure to do so may result in damage to the product or personal injury. Using the fallen product again may result in  
electric shock or fire. Contact the service center.  
7
Precautions When Using the Product  
WARNING  
Failure to observe these warnings may result in serious injury or death.  
Do not disassemble, repair or modify the product by yourself.  
- Otherwise, the product may cause fire or electric shock. If the product needs to be checked, adjusted or repaired,  
contact the service center.  
Do not allow water to get into the product and do not let the product get wet.  
- Failure to do so may result in fire, electric shock, malfunction or deformation.  
If there is a gas leak, do not touch the power outlet, and open the windows for ventilation.  
- Otherwise, the product may cause fire or electric shock.  
Do not impact the front or sides of the screen with a hard object, such as a metal object, and do not scratch the  
screen.  
- This can result in damage to the screen.  
In the event that liquid or a foreign object falls into the product, please switch it off and unplug it from the wall outlet  
and contact the service center.  
- Otherwise, the product may cause fire or electric shock.  
Make sure that children do not swallow the remote control batteries when you replace them. Keep batteries out of  
reach of children.  
- If a child swallows a battery, consult a doctor immediately.  
In the event that no image appears on the screen or no sound is heard, stop using the product. Switch it off  
immediately, unplug it from the power outlet and contact the service center.  
- Otherwise, the product may cause fire or electric shock.  
Do not use the product in any environment with excessively high temperatures or humidity.  
Using headsets (earphones) for a long time or listening at high volume can cause damage to your hearing.  
Do not use high-voltage electrical products near the device. This may result in device malfunction due to electric  
shock. (e.g. electric mosquito swatters)  
If the enclosure has been damaged, consult the service center. There is a risk of electric shock or personal injury.  
8
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
Do not use or store the product near inflammables.  
- This may result in fire or explosion.  
Take a break to protect your health and vision when using the product for long periods of time.  
Displaying a still image for a prolonged time may cause damage to the screen, resulting in image sticking.  
- Damage incurred as a result of the above is not covered by the product warranty.  
Do not push hard on or scratch the product’s surface with your hands or sharp objects, such as nails, pencils or pens.  
- This may damage the product’s surface and cause it to malfunction.  
Keep the product clean.  
Refer to the user guide and set the product to a fitting resolution and frequency. (For models with PC support only)  
- You may experience blurred vision.  
Because the LCD requires high technology consisting of millions of pixels, pixilated spots (red, green, white or black)  
may appear on the screen in some cases while using the product.  
- This is normal for an LCD screen and is not a malfunction, nor is this related to the product’s performance.  
Do not leave the product in places where it is likely to get wet, and do not place anything containing liquid on top of  
the product such as a flower vase.  
To clean the front frame, spray water onto a soft cloth two to four times; wipe in one direction only.  
- Too much moisture may cause staining.  
Precautions When Cleaning the Product  
WARNING  
Failure to observe these warnings may result in serious injury or death.  
Do not spray water directly onto the product and do not use inflammable materials such as thinner or benzene to  
wipe the product.  
- Doing so may cause fire or result in electric shock.  
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
To clean the product, unplug the power cord and wipe it gently with a soft cloth.  
When cleaning the product or the screen, do not use cleanser, automobile or industrial shiner, abrasive or wax,  
benzene, alcohol, etc., as this may damage the product.  
- This may result in fire, electric shock or product damage (deformation, corrosion or breakage).  
9
Precautions When Experiencing Image Sticking  
Displaying a still image for a prolonged period of time may cause damage to the screen, resulting in image sticking.  
Use a screen saver when using the monitor for a prolonged period of time.  
Most third-party products have the same issue. The resulting damage is not covered by the product warranty.  
Precautions When Using the Remote Control  
CAUTION  
Failure to observe these instructions may result in minor injury or damage to the product.  
Remove any obstacles.  
The remote control may not function properly in sunlight or under a strong lamp. Move the product if it is being used  
in these conditions.  
Only use the specified type of battery. Do not insert batteries that are not rechargeable into the charger.  
- Burst or leaking batteries may cause fire or electric shock.  
Avoid locations near heaters or locations with high humidity.  
Do not mix new batteries with old ones.  
- Burst or leaking batteries may cause fire or electric shock.  
Do not expose the batteries to excessive heat. Keep them away from direct sunlight, fireplaces, electric heaters, etc.  
10  
LICENSES  
Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.  
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered  
trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.  
Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, Dolby Atmos, and the double-D  
symbol are trademarks of Dolby Laboratories.  
& DTS and the Symbol together, DTS 2.0 Channel, DTS 2.0+Digital Out, DTS-HD, and DTS Virtual:X are registered  
trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.  
11  
ASSEMBLY AND PREPARATION  
CAUTION  
Always use genuine components to ensure safety and product performance.  
The product warranty will not cover damage or injury caused by the use of counterfeit components.  
NOTE  
The accessories provided with your product may vary depending on the model or region.  
Product specifications or contents in this manual may be changed without prior notice due to upgrade of product  
functions.  
SuperSign Software & Manual  
- Downloading from the LG Electronics website.  
- Visit the LG Electronics website (http://partner.lge.com) and download the latest software for your model.  
The warranty will not cover any damage caused by using the product in an excessively dusty environment.  
12  
Product Contents  
The image may be different according to the model.  
Illuminance sensor /  
IR Receiver  
Power Indicator  
Magnet Sensor  
Circuit Breaker  
Power Off: Green  
Power On: Red  
* This image shows the product with the back cover off.  
13  
Installing in Landscape Orientation  
To install in landscape orientation, rotate the screen counterclockwise 90 degrees while facing it from the front.  
Pixel Sensor  
Pixel Sensor  
NOTE  
The 75XE3C does not support installation in landscape orientation.  
Installing on a Wall  
For proper ventilation, make sure the product is installed at least 100 mm away from the walls on every side. Consult a  
professional installation company near you for details on installation.  
100 mm  
100 mm  
100 mm  
100 mm  
14  
Enclosure Installation Guide  
FIXING THE PANEL SCREW HOLES  
Use the side screw holes when mounting the panel.  
Side screw hole  
- 55XE3C : M8, Torque - 17 Kgf to 27 Kgf (Bottom side: 8 holes, Left, Right Sides: each of 4 holes)  
- 75XE3C : M10, Torque - 17 Kgf to 27 Kgf (Bottom side: 10 holes, Left, Right Sides: each of 4 holes)  
Please use the 18.0 mm to 25.0 mm screws.  
(Unit: mm)  
316.0  
2-M16 Lifting Hole  
316.0  
2-Ø10.0 Lifting Hole  
503  
503  
89.5  
80.5  
67.8  
80.5  
4-M10  
Mounting Hole  
4-M10  
108.1  
108.1  
4-Ø8.0 Mounting Hole  
Mounting Hole  
4-Ø8.0 Mounting Hole  
164.7  
152.4  
164.7  
152.4  
820  
820  
711.2  
152.4  
711.2  
152.4  
720  
720  
40.0  
289.2  
289.2  
40.0  
8-Ø8.0 Mounting Hole  
30.6  
40.0  
509  
309  
509  
309  
100 100  
10-M10 Mounting Hole  
55XE3C  
75XE3C  
CAUTION  
Disconnect the power cord before moving or installing the monitor to avoid risk of electric shock.  
If you install the monitor on a ceiling or slanted wall, it may fall and result in injury. The product should be installed by  
a professional installation company specified by the retail store.  
Do not over tighten the screws as this may damage the monitor and void your warranty.  
Any damage or injuries caused by misuse or use of improper accessories are not covered by the warranty.  
To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.  
(This pertains only to Australia and New Zealand.)  
NOTE  
Be sure to use the correct length.  
15  
Safety and Precaution Guide for Installation  
Direct Sunlight  
While powered off, make sure the device is not exposed to direct sunlight for a prolonged period.  
- Protect the display with cloth or a box when storing the device after it has been powered off.  
- This can prevent faults such as black spots, creases, and yellowing.  
After connecting the power, activate the [Screen off & Backlight (Outdoor mode)] feature.  
- Turning the screen off can help prevent black spots, creases, yellowing, condensation, and malfunctions due to  
moisture.  
- For the [Screen off & Backlight (Outdoor mode)] feature, please refer to the User Guide on our homepage.  
- At sub-zero temperatures, the display will be able to turn on after the internal temperature rises.  
CAUTION  
16  
REMOTE CONTROL  
The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully to  
use the monitor correctly. To install batteries, open the battery cover, place batteries (1.5 V AAA) matching  
and  
terminals to the labels inside the compartment, and close the battery cover. To remove the batteries, perform the  
installation actions in reverse. The illustrations may differ from the actual accessories.  
CAUTION  
Do not mix old and new batteries, as this may damage the remote control.  
Be sure to point the remote control toward the remote control sensor on the monitor.  
Some features of the remote control may not be supported in certain models.  
A
(POWER) Turns the monitor on or off.  
MONITOR ON Turns the monitor on.  
A
MONITOR OFF Turns the monitor off.  
ENERGY SAVING  
Adjusts the brightness of the picture to  
reduce energy consumption.  
(INPUT) Selects the input mode.  
Used for viewing 3D videos.  
B
C
B
1/a/A Toggles between numerical and alphabetical.  
Number and Alphabet buttons Enters numerical or alphabetical  
characters depending upon the setting.  
CLEAR Deletes the entered numerical or alphabetical character.  
C
Volume Up/Down Button Adjusts the volume.  
ARC Selects the Aspect Ratio mode.  
AUTO Automatically adjusts picture position and minimizes image  
instability (available for RGB input only).  
(MUTE) Mutes all sounds.  
BRIGHTNESS Adjusts the brightness of the display. PAGE function  
is not supported in this model.  
17  
D
PSM Selects the Picture Mode.  
(HOME) Activates the Launcher.  
W.BAL Enters the White Balance menu.  
D
E
E
(SETTINGS) Accesses the main menus or saves your input and  
exit menus.  
S.MENU SuperSign menu key.  
Navigation Buttons Scrolls through menus or options.  
Selects menus or options and confirms your input.  
(BACK) Allows you to move back one step in the user interaction  
function.  
F
EXIT Quit all OSD tasks and applications.  
F
Allows you to control various multimedia devices to  
enjoy multimedia simply by using the remote control through the  
SimpLink menu.  
TILE Selects the TILE Mode.  
PICTURE ID ON/OFF When the Picture ID number matches the Set  
ID number, you can control whichever monitor you want in multi-  
display format.  
USB Menu Control Buttons Controls media playback.  
18  
MAKING CONNECTIONS  
You can connect various external devices to your monitor. Change the input mode and select the external device you  
want to connect.  
For more information about external device connections, see the user manual provided with each device.  
Connecting to a PC  
Some of the cables are not provided.  
This monitor supports the Plug and Play* feature.  
* Plug and Play: a feature that enables a PC to recognize devices attached by the user without device configuration or  
user intervention when powering up.  
External Device Connection  
Connect a HD receiver, DVD, or VCR player to the monitor and select an appropriate input mode.  
Some of the cables are not provided. For the best picture and sound quality, connecting external devices to your  
monitor using HDMI cables is recommended.  
19  
NOTE  
For the best image quality, using the monitor with HDMI connection is recommended.  
To comply with the standard specifications of the product, use a shielded interface cable with a ferrite core, such as a  
DVI-D cable.  
If you turn the monitor on when the set is cold, the screen may flicker. This is normal.  
Sometimes red, green, or blue spots may appear on the screen. This is normal.  
Use a High Speed HDMI®/TM cable (shorter than 3 meters).  
Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not  
display or a connection error may occur.  
Recommended HDMI Cable Types  
- High Speed HDMI®/TM Cable  
- High Speed HDMI®/TM Cable with Ethernet  
If you cannot hear any sound in HDMI mode please check your PC settings. Some PCs require you to manually change  
the default audio output to HDMI.  
If you want to use HDMI-PC mode, you must set your PC/DTV to PC mode.  
You may experience compatibility issues if you use HDMI-PC mode.  
Make sure the power cable is disconnected.  
If you connect a gaming device to the monitor, use the cable provided with the gaming device.  
High Speed HDMI®/TM cables transmit a HD signal up to 1080p and higher.  
CAUTION  
Connect the signal input cable and tighten it by turning the screws clockwise.  
Do not press the screen with your finger for a prolonged period as this may result in temporary distortion on the  
screen.  
Avoid displaying static images on the screen for a long period of time to prevent image retention. Use a screensaver  
if possible.  
A wireless communication device near your monitor can affect the image.  
20  
To Connect External Devices  
When Installing a Media Player Internally  
- 55XE3C  
(Unit: mm)  
4-M3 Mounting Hole  
128  
- 75XE3C  
(Unit: mm)  
4-M3 Mounting Hole  
128  
4-M3 Mounting Hole  
128  
Remove the rear cover.  
Mount the media player by using the bracket for the media player.  
Screw hole: M3.0, Torque - 5 Kgf to 10 Kgf  
See the included guide for details on cable connection.  
21  
When Installing a Media Player/PC Externally  
- 55XE3C  
- 75XE3C  
NOTE  
If you set the tile mode using DVI-D or HDMI, you will not be able to watch HDCP-encrypted content.  
If the signal cable between the product and your PC is too long, make sure to use the Booster or optical cable.  
DP Cable - Use a DP cable that is certified to DP 1.1a standard or higher.  
When installing a media player/PC externally, you can only connect HDMI IN, USB 3.0 IN and LAN.  
22  
Using the Input List  
(HOME)  
HDMI DVI-D DISPLAYPORT  
23  
TROUBLESHOOTING  
No image is displayed.  
Problem  
Action  
Is the product power cord connected?  
Check if the power cord is correctly plugged into the power outlet.  
Check whether the circuit breaker has been connected properly. The  
switch of the circuit breaker must be set to on (red).  
When operating in below zero temperature, the enclosure may not  
work for up to one hour to raise the internal temperature of the  
enclosure.  
Does the “Invalid Format” message  
appear?  
The signal from the PC (Graphics card) is out of the vertical or  
horizontal frequency range of the product. Adjust the frequency range  
by referring to the Specifications in this manual.  
Does the “No Signal” message appear?  
The signal cable between PC and product is not connected. Check the  
signal cable.  
Access the input menu to check the input signal.  
The Unknown Product message appears when the product is connected.  
Problem  
Action  
Did you install the driver?  
Check if the Plug and Play function is supported by referring to the  
graphics card user manual.  
24  
The screen image looks abnormal.  
Problem  
Action  
Is the screen position wrong?  
Check if the graphics card resolution and frequency are supported by  
the product. If the frequency is out of range, set to the recommended  
resolution in the [Control Panel] [Display] [Setting] menu. (The  
settings may differ depending on your operating system.)  
The screen is displayed abnormally.  
The proper input signal is not connected to the signal port. Connect  
the signal cable that matches with the source input signal.  
Condensation may appear on the screen. It will disappear in a certain  
period of time after the product is powered on.  
- The condensation formed inside the product is a natural  
phenomenon and is not covered under warranty. (IPX6 is a standard  
to protect the product from 100L of water per minute and not from  
infiltration of moisture in the air into the set.)  
The screen’s brightness seems dark.  
Change the screen brightness settings.  
Check the Easy Brightness Control settings.  
If the internal temperature of the enclosure rises, the screen’s  
brightness may darken.  
Make sure to regularly clean the heat exchanger within the enclosure.  
After-image appears on the product.  
Problem  
Action  
After-image appears when the product is If you use a fixed image for a long time, the pixels may be damaged.  
turned off.  
Use the screen-saver function.  
When a dark image is displayed on the screen after an image with high  
contrast (black and white or gray), this may cause image sticking. This  
is normal for LCD screen products.  
The audio function does not work.  
Problem  
Action  
See if the audio cable is connected properly.  
Adjust the volume.  
No sound?  
See if the sound is set properly.  
Select the appropriate equalizer sound.  
Adjust the volume.  
Sound is too dull.  
Sound is too low.  
25  
Screen color is abnormal.  
Problem  
Action  
Screen has poor color resolution (16  
colors).  
Set the number of colors to more than 24 bits (true color). Select  
[Control Panel] [Display] [Settings] [Color Table] in Windows.  
(The settings may differ depending on your operating system.)  
Screen color is unstable or mono-colored. Check the connection status of the signal cable. Or, re-insert the PC  
graphics card.  
Do black spots appear on the screen?  
Several pixels (red, green, blue, white, or black color) may appear on  
the screen, which can be attributable to the unique characteristics of  
the LCD panel. This is not a malfunction of the LCD.  
The operation does not work normally.  
Problem  
Action  
Is the Timer set?  
The power suddenly turned off.  
Check the power control settings. Power interrupted.  
Check whether the circuit breaker has been connected properly. The  
switch of the circuit breaker must be set to on (red).  
If the internal temperature of the enclosure rises, the power may shut  
down.  
Make sure to regularly clean the heat exchanger within the enclosure.  
26  
CAUTION  
Image sticking does not occur when using constantly changing images but may occur when using a fixed image for an  
extended period of time. Therefore, it is recommended that you use the instructions below to decrease the likelihood  
of image sticking occurring when using a fixed image. It is recommended that you change the screen at least once  
every 12 hours at the very minimum; if done more frequently, the prevention of image sticking is more effective.  
Recommended operating conditions  
1
Change the background and the character colors using the same time interval.  
ID: UPM 123  
PW: ****  
ID: UPM 123  
PW: ****  
When changing colors, using complementary colors helps to prevent image sticking.  
Glass  
BM  
BM  
BM  
CF  
CF  
CF  
CF  
OC  
PI  
LC  
PI  
TFT Layers  
Glass  
ITO or MoTi Pixel Layer  
2
Change the image using the same time interval.  
Make sure that the characters or images before changing the image remain in the same location after changing the  
image.  
What is image sticking?  
When the LCD panel displays a static image for an extended period of time, it can cause a voltage difference between  
the electrodes that operate the liquid crystals. When the voltage difference between the electrodes builds up over  
time, liquid crystals have a tendency to remain aligned in one direction. During this process, a previously displayed image  
remains visible. This phenomenon is referred to as image sticking.  
27  
PRODUCT SPECIFICATIONS  
The product specifications below may be changed without prior notice due to upgrade of product functions.  
” refers to alternating current (AC), and “  
” refers to direct current (DC).  
LCD screen  
Video signal  
Screen type  
Thin Film Transistor (TFT)  
Liquid Crystal Display (LCD) Screen  
Maximum resolution  
55XE3C  
75XE3C  
1920 × 1080 @ 60 Hz  
HDMI / DisplayPort : 3840 × 2160 @ 60 Hz  
DVI-D : 1920 × 1080 @ 60 Hz  
- This may not be supported on some OS or graphics card types.  
Recommended resolution 55XE3C  
75XE3C  
1920 × 1080 @ 60 Hz  
HDMI / DisplayPort : 3840 × 2160 @ 60 Hz  
DVI-D : 1920 × 1080 @ 60 Hz  
- This may not be supported on some OS or graphics card types.  
HDMI / DVI-D / DisplayPort 55XE3C : 30 kHz to 83 kHz  
75XE3C : 30 kHz to 135 kHz  
Horizontal frequency  
Vertical frequency  
Synchronization  
HDMI / DVI-D / DisplayPort 55XE3C : 56 Hz to 60 Hz  
75XE3C : 30 Hz to 60.31 Hz  
Digital  
Input / Output ports When installing the media RS-232C IN/OUT, SPEAKER OUT, HDMI IN, DP IN/OUT, DVI-D IN,  
player inside SD, USB 3.0 IN, AUDIO IN, LAN  
When installing the media HDMI IN, USB 3.0 IN, LAN  
player / PC outside  
Embedded battery  
Applied  
Environmental  
Conditions  
Operating Temperature  
Operating Humidity  
Storage Temperature  
Storage Humidity  
-30 °C to 50 °C  
5 % to 100 %  
-20 °C to 60 °C  
5 % to 100 %  
28  
55XE3C  
LCD Panel  
Power  
Pixel Pitch  
0.630 mm (H) x 0.630 mm (V)  
Rated Voltage  
AC 100-240 V ~ 50/60 Hz 5.3 A  
Power Consumption On Mode: 350 W (Typ) / 500 W (Max)  
Sleep Mode: ≤ 0.5 W  
Standby Mode: ≤ 0.5 W  
Dimensions (Width x Height x Depth) / Weight  
745.3 mm x 1345.4 mm x 160.0 mm / 70.0 kg  
75XE3C  
LCD Panel  
Power  
Pixel Pitch  
Rated Voltage  
0.429 mm (H) x 0.429 mm (V)  
AC 200-240 V~ 50/60 Hz 5.7 A  
AC 100-240 V ~ 50/60 Hz 11.4 A (For Philippines,  
Taiwan, Canada, United States, Mexico, Colombia,  
Argentina)  
Power Consumption On Mode: 700 W (Typ) / 1000 W (Max)  
Sleep Mode: ≤ 0.5 W  
Standby Mode: ≤ 0.5 W  
Dimensions (Width x Height x Depth) / Weight  
1075.6 mm x 1991.6 mm x 219 mm / 180 kg  
29  
HDMI / DVI-D / DisplayPort (PC) Support Mode  
Resolution  
640 x 480  
Horizontal frequency (kHz)  
Vertical frequency (Hz)  
Remark  
31.469  
37.879  
48.363  
44.772  
47.712  
63.981  
65.290  
67.5  
59.94  
60.317  
60  
800 x 600  
1024 x 768  
1280 x 720  
1366 x 768  
1280 x 1024  
1680 x 1050  
1920 x 1080  
59.855  
60  
60.02  
59.954  
60  
Only 75XE3C  
(HDMI / DisplayPort)  
Only 75XE3C  
3840 x 2160  
3840 x 2160  
67.5  
135  
30  
60  
(HDMI / DisplayPort)  
HDMI / DisplayPort (DTV) mode  
Resolution  
480/60p  
576/50p  
720/50p  
720/60p  
1080/50i  
1080/60i  
1080/50p  
1080/60p  
2160/30p  
2160/50p  
2160/60p  
Horizontal frequency (kHz)  
Vertical frequency (Hz)  
Remark  
31.5  
31.25  
37.5  
45  
60  
50  
50  
60  
50  
60  
50  
60  
30  
50  
60  
28.1  
33.75  
56.25  
67.5  
67.5  
112.5  
135  
Only 75XE3C  
Only 75XE3C  
Only 75XE3C  
30  
NOTE  
When using HDMI/DVI-D/DisplayPort inputs, PC and DTV resolutions can be adjusted in the Input Label.  
Vertical frequency: The product display functions by the screen image changing dozens of times every second like a  
fluorescent lamp.  
The vertical frequency or refresh rate is the number of image displays per second. The unit is Hz.  
Horizontal frequency: The horizontal interval is the time taken to display one horizontal line. When 1 is divided by  
the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal  
frequency. The unit is kHz.  
Make sure to read the Safety Precautions before using the  
product.  
The model and serial numbers of the SET are located on the  
back and one side of the SET. Record it below should you ever  
need service.  
MODEL  
SERIAL  
Temporary noise is normal when powering ON or OFF this  
device.  

Toshiba Carrier Rav Sp300at2 Ul User Manual
Soleus Air 3046364 User Manual
Sharp Lc1060 User Manual
Sharp Ar M160 User Manual
Sanyo Kr Ch 25 User Manual
Samsung Aw14pk Series User Manual
Philips Lr03ep2a User Manual
EMERSON EVC655 User Manual
CRAFTSMAN ZTS 7500 107.27790 User Manual
BLACK DECKER NVB215W User Manual