LG 49UF7600 UJ User Manual

OWNER’S MANUAL  
Safety and Reference  
LED TV*  
* LG LED TVs are LCD TVs with LED backlighting.  
Please read this manual carefully before operating your TV and retain  
it for future reference.  
43UF7600  
49UF7600  
55UF7600  
60UF7650  
65UF7650  
70UF7650  
60UF7690  
65UF7690  
60UF7700  
65UF7700  
70UF7700  
79UF7700  
55UF8500  
60UF8500  
65UF8500  
55UF8600  
65UF8600  
55UF9500  
65UF9500  
55UG8700  
65UG8700  
*MFL68741502*  
P/No : MFL68741502 (1503-REV02)  
Use only with the cart, stand, tripod, bracket, or  
table specified by the manufacturer, or sold with  
the apparatus. When a cart is used, use caution  
when moving the cart/apparatus combination to  
avoid injury from tip-over.  
CAUTION concerning the Power Cord  
(Can differ by country):  
Check the specification page of this owner’s  
manual to be certain. Do not connect too many  
appliances to the same AC power outlet as this  
could result in fire or electric shock. Do not  
overload wall outlets. Overloaded wall outlets,  
loose or damaged wall outlets, extension cords,  
frayed power cords, or damaged or cracked  
wire insulation are dangerous. Any of these  
conditions could result in electric shock or fire.  
Periodically examine the cord of your appliance,  
and if its appearance indicates damage or  
deterioration, unplug it, discontinue use of the  
appliance, and have the cord replaced with  
an exact replacement part by an authorized  
service. Protect the power cord from physical or  
mechanical abuse, such as being twisted, kinked,  
pinched, closed in a door, or walked upon. Pay  
particular attention to plugs, wall outlets, and  
the point where the cord exits the appliance. Do  
not move the TV with the power cord plugged  
in. Do not use a damaged or loose power cord.  
Be sure do grasp the plug when unplugging the  
power cord. Do not pull on the power cord to  
unplug the TV.  
Unplug this apparatus during lightning storms  
or when unused for long periods of time.  
Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has  
been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been spilled  
or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture,  
does not operate normally, or has been dropped.  
Do not press strongly upon the panel with a  
hand or a sharp object such as a nail, pencil, or  
pen, or make a scratch on it.  
Warning - To reduce the risk of fire or electrical  
shock, do not expose this product to rain,  
moisture or other liquids. Do not touch the TV  
with wet hands. Do not install this product near  
flammable objects such as gasoline or candles,  
or expose the TV to direct air conditioning.  
Do not stick metal objects or any other  
conductive material into the power cord. Do  
not touch the end of the power cord while it is  
plugged in.  
Keep the packing anti-moisture material or  
vinyl packing out of the reach of children.  
Anti-moisture material is harmful if swallowed.  
If swallowed, induce vomiting and go to the  
nearest hospital. Additionally, vinyl packing can  
cause suffocation. Keep it out of the reach of  
children.  
Do not expose to dripping or splashing and  
do not place objects filled with liquids, such as  
vases, cups, etc. on or over the apparatus (e.g.,  
on shelves above the unit).  
3
Grounding  
Cleaning  
(Except for devices which are not grounded.)  
Ensure that you connect the earth ground wire  
to prevent possible electric shock (i.e., a TV  
with a three-prong grounded AC plug must  
be connected to a three-prong grounded AC  
outlet).  
When cleaning, unplug the power cord and wipe  
gently with a soft cloth to prevent scratching. Do  
not spray water or other liquids directly on the  
TV as electric shock may occur. Do not clean with  
chemicals such as alcohol, thinners, or benzene.  
Moving  
If grounding methods are not possible, have  
a qualified electrician install a separate circuit  
breaker. Do not try to ground the unit by  
connecting it to telephone wires, lightning rods,  
or gas pipes.  
Make sure the product is turned off, unplugged,  
and all cables have been removed. It may take 2  
or more people to carry larger TVs. Do not press  
or put stress on the front panel of the TV.  
Ventilation  
Install your TV where there is proper ventilation.  
Do not install in a confined space such as a  
bookcase. Do not cover the product with cloth or  
other materials while plugged in. Do not install  
in excessively dusty places.  
If you smell smoke or other odors coming from  
the TV, unplug the power cord and contact an  
authorized service center.  
Keep the product away from direct sunlight.  
Never touch this apparatus or antenna during a  
lightning storm.  
Power  
Supply  
Circuit  
Breaker  
As long as this unit is connected to the AC wall  
outlet, it is not disconnected from the AC power  
source even if the unit is turned off.  
Do not attempt to modify this product in any  
way without written authorization from LG  
Electronics. Unauthorized modification could  
void the user’s authority to operate this product.  
Outdoor Antenna Grounding  
When mounting a TV on the wall, make sure not  
to install the TV by hanging the power and signal  
cables on the back of the TV.  
(Can differ by country):  
If an outdoor antenna is installed, follow the  
precautions below. An outdoor antenna system  
should not be located in the vicinity of overhead  
power lines or other electric light or power  
circuits, or where it can come in contact with  
such power lines or circuits as death or serious  
injury can occur. Be sure the antenna system is  
grounded to provide some protection against  
voltage surges and built-up static charges.  
Section 810 of the National Electrical Code (NEC)  
in the U.S.A. provides information with respect  
to proper grounding of the mast and supporting  
structure, grounding of the lead-in wire to  
an antenna discharge unit, size of grounding  
conductors, location of antenna discharge  
unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
Antenna grounding according to the National  
Electrical Code, ANSI/NFPA 70  
Do not allow an impact shock or any objects to  
fall into the product, and do not drop anything  
onto the screen.  
DISCONNECTING THE DEVICE FROM THE  
MAIN POWER  
The power plug is the disconnecting device.  
In case of an emergency, the power plug must  
remain readily accessible.  
Batteries  
Store the accessories (battery, etc.) in a safe  
location out of the reach of children.  
This apparatus uses batteries. In your community  
there might be regulations that require you  
to dispose of these batteries properly due to  
environmental considerations. Please contact  
your local authorities for disposal or recycling  
information.  
Do not dispose of batteries in a fire.  
Do not short circuit, disassemble, or allow the  
batteries to overheat.  
Antenna Lead in Wire  
Antenna Discharge Unit  
(NEC Section 810-20)  
Ground Clamp  
Electric Service  
Equipment  
Grounding Conductor  
(NEC Section 810-21)  
Ground Clamp  
Power Service Grounding  
Electrode System  
(NEC Art 250, Part H)  
NEC: National Electrical Code  
4
Do not use high voltage electrical equipment  
near the TV, (e.g., a bug zapper).  
This may result in product malfunction.  
Dot Defect  
Avoid displaying a fixed image on the TV screen  
for a long period of time (2 or more hours for  
LCD, 1 or more hours for the Plasma TV) to  
prevent image burn.  
The panel is a high technology product with  
resolution of two million to six million pixels.  
In a very few cases, you could see fine dots on  
the screen while you’re viewing the TV. Those  
dots are deactivated pixels and do not affect the  
performance and reliability of the TV.  
FCC Notice  
(For USA)  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses  
and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instructions, may cause harmful interference  
to radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning  
the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of  
the following measures:  
Generated Sound  
Cracking noise A cracking noise that occurs  
when watching or turning off the TV is  
generated by plastic thermal contraction due to  
temperature and humidity. This noise is common  
for products where thermal deformation is  
required.  
Electrical circuit humming/panel buzzing  
A low level noise is generated from a high-  
speed switching circuit, which supplies a large  
amount of current to operate a product. It varies  
depending upon the product. This generated  
sound does not affect the performance and  
reliability of the product.  
Take care not to touch the ventilation openings.  
When watching the TV for a long period, the  
ventilation openings may become hot. This does  
not affect the performance of the product or  
cause defects in the product.  
Do not install this product on a wall if it could be  
exposed to oil or oil mist. This may damage the  
product and cause it to fall.  
If the TV feels cold to the touch, there may  
be a small flicker when it is turned on. This is  
normal; there is nothing wrong with TV. Some  
minute dot defects may be visible on the screen,  
appearing as tiny red, green, or blue spots.  
However, they have no adverse effect on the TV’s  
performance. Avoid touching the LCD screen or  
holding your finger(s) against it for long periods  
of time. Doing so may produce some temporary  
distortion effects on the screen.  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment  
and the receiver.  
- Connect the equipment to an outlet on a circuit  
different from that to which the receiver is  
connected.  
- Consult the dealer or an experienced radio/TV  
technician for help.  
This device complies with part 15 of the FCC  
Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful  
interference and (2) this device must accept any  
interference received, including interference that  
may cause undesired operation of the device. Any  
changes or modifications in construction of this  
device which are not expressly approved by the  
party responsible for compliance could void the  
user’s authority to operate the equipment.  
Preventing image burn or burn-in on  
your TV screen  
If a fixed image displays on the TV screen for  
a long period of time, it will be imprinted and  
become a permanent disfigurement on the  
screen. This is image burn or burn-in and not  
covered by the warranty.  
If the aspect ratio of the TV is set to 4:3 for a long  
period of time, image burn may occur on the  
letterboxed area of the screen.  
5
The maximum antenna gain permitted for  
devices in the bands 5250–5350 MHz and  
5470–5725 MHz shall comply with the EIRP limit;  
and  
The maximum antenna gain permitted for  
devices in the band 5725–5825 MHz shall  
comply with the e.i.r.p. limits specified for point-  
to-point and non point-to-point operation as  
appropriate.  
High-power radars are allocated as primary users  
(i.e. priority users) of the bands 5250–5350 MHz  
and 5650–5850 MHz and that these radars could  
cause interference and/or damage to LE-LAN  
FCC Radio Frequency Interference  
Requirements (for UNII devices)  
High power radars are allocated as primary users  
of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.  
These radar stations can cause interference with  
and/or damage this device. This device cannot be  
co-located with any other transmitter.  
FCC RF Radiation Exposure Statement  
[For having wireless function (WLAN, Bluetooth,...)]  
This equipment complies with FCC radiation  
exposure limits set forth for an uncontrolled  
environment. This transmitter must not be  
colocated or operating in conjunction with any  
other antenna or transmitter. This equipment  
should be installed and operated with minimum  
distance 20 cm (7.8 inches) between the radiator  
and your body. Users must follow the specific  
operating instructions for satisfying RF exposure  
compliance.  
devices.  
Note to Cable/TV Installer  
(For USA and Canada)  
This reminder is provided to call the CATV system  
installer’s attention to Article 820-40 of the  
National Electric Code (U.S.A.). The code provides  
guidelines for proper grounding and, in particular,  
specifies that the cable ground shall be connected  
to the grounding system of the building, as close  
to the point of the cable entry as practical.  
Industry Canada Statement  
(For Canada)  
[For having wireless function (WLAN, Bluetooth,...)]  
This device complies with RSS-210 of the Industry  
Canada Rules. Operation is subject to the following  
two conditions:  
1. this device may not cause interference and  
2. this device must accept any interference,  
including interference that may cause undesired  
operation of the device.  
LG Recycling Policy  
(For USA)  
LG Electronics offers a customized e-waste  
takeback and recycling service that meets  
local needs and requirements in the countries  
where e-waste regulations are in place, and also  
provides product and packaging takeback and  
recycling service voluntarily in some countries.  
LG Electronics evaluates productsrecyclability at  
the design step using LG’s recyclability evaluation  
tool, with the goal of improving recyclability where  
practicable. Through these activities, LG seeks to  
contribute to conserving natural resources and  
protecting the environment.  
IC Radiation Exposure Statement  
(For Canada)  
[For having wireless function (WLAN, Bluetooth,...)]  
This equipment complies with IC radiation  
exposure limits set forth for an uncontrolled  
environment. This equipment should be installed  
and operated with minimum distance 20 cm  
(7.8 inches) between the antenna & your body.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE  
FOR ANY RADIO OR TV INTERFERENCE CAUSED  
BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD  
VOID THE USER’S AUTHORITY TO OPERATE THE  
EQUIPMENT.  
For more information about the LG Recycling  
Policy, please visit our global site at  
environment takeback- recycling  
WARNING  
(For Canada)  
[For product having the wireless function using  
5 GHz frequency bands]  
The device for operation in the band 5150–5250  
MHz is only for indoor use to reduce the  
potential for harmful interference to co-channel  
mobile satellite systems;  
6
Viewing 3D Imaging  
(For 3D models)  
CAUTION  
Viewing Environment  
Viewing Distance  
- Maintain a distance of at least twice the screen’s  
diagonal length when watching 3D content.  
If you feel discomfort in viewing 3D content,  
move further away from the TV.  
WARNING  
Viewing Environment  
Viewing Time  
- When watching 3D content, take 5 to 15 minute  
breaks every hour. Viewing 3D content for  
a long period of time may cause headache,  
dizziness, fatigue, or eye strain.  
Viewing Age  
Infants / Children  
- Usage/ Viewing 3D content for children under  
the age of 5 are prohibited.  
- Children under the age of 10 may overreact and  
become overly excited because their vision is  
in development, for example, trying to touch  
the screen or trying to jump into it. Special  
monitoring and extra attention is required for  
children watching 3D content.  
Those that have a photosensitive  
seizure or chronic illness  
Some users may experience a seizure or other  
abnormal symptoms when they are exposed  
to a flashing light or particular pattern from 3D  
content.  
Do not watch 3D videos if you feel nauseous,  
are pregnant and/ or have a chronic illness such  
as epilepsy, cardiac disorder, or blood pressure  
disease, etc.  
3D Content is not recommended for those who  
suffer from stereo blindness or stereo anomaly.  
Double images or discomfort in viewing may be  
experienced.  
If you have strabismus (cross-eyed), amblyopia  
(weak eyesight), or astigmatism, you may have  
trouble sensing depth and easily feel fatigue  
due to double images. It is advised to take more  
frequent breaks than the average adult.  
If your eyesight varies between your right and  
left eye, correct your eyesight prior to watching  
3D content.  
- Children have greater binocular disparity of 3D  
presentations than adults because the distance  
between the eyes is shorter than one of adults.  
Therefore they will perceive more stereoscopic  
depth compared to adults for the same 3D  
image.  
Teenagers  
- Teenagers may be stimulated to light coming  
from 3D videos. Advise them not to watch 3D  
videos for a long time when they are tired.  
Elderly  
- The elderly may perceive less of a 3D effect  
than the youth. Do not sit closer to the TV than  
the recommended distance.  
Cautions when using the 3D glasses  
Only use LG 3D glasses. Otherwise, you may not  
be able to view 3D videos properly.  
Symptoms which require  
discontinuation or refraining from  
watching 3D content  
Do not watch 3D content when you feel fatigue  
from lack of sleep, overwork, or intoxication.  
When these symptoms are experienced, stop  
using/watching 3D content and get enough rest  
until the symptom subsides.  
- Consult your doctor when the symptoms  
persist. Symptoms may include headache,  
eyeball pain, dizziness, nausea, palpitation,  
blurriness, discomfort, double image, eyestrain,  
or fatigue.  
Do not use 3D glasses instead of your normal  
glasses, sunglasses, or protective goggles.  
Using modified 3D glasses may cause eye strain  
or image distortion.  
Do not keep your 3D glasses in extremely high or  
low temperatures. It will cause deformation.  
The 3D glasses are fragile and are easily  
scratched. Use a soft, clean piece of cloth when  
wiping the lenses. Do not scratch the lenses of  
the 3D glasses with sharp objects or clean/wipe  
them with chemicals.  
7
Preparing  
CAUTION  
Do not use any unapproved items to ensure the  
safety and product’s lifespan.  
Any damages or injuries by using unapproved  
items are not covered by the warranty.  
Some models appear to have a thin film on the  
screen. It is actually part of the screen; do not  
remove it.  
Do not remove the panel with your fingers or  
any tools. Doing so may damage the product.  
(For 55/65UF9500)  
NOTE  
Image shown may differ from your TV.  
Your TV’s OSD (On Screen Display) may differ  
slightly from that shown in this manual.  
The available menus and options may differ from  
the input source or product model that you are  
using.  
New features may be added to this TV in the  
future.  
The items supplied with your product may vary  
depending upon the model.  
Product specifications or contents of this manual  
may be changed without prior notice due to  
upgrade of product functions.  
For an optimal connection, HDMI cables and  
USB devices should have bezels less than 10 mm  
(0.39 inches) thick and 18 mm (0.7 inches) width.  
Use an extension cable that supports USB 2.0 if  
the USB cable or USB flash drive does not fit into  
your TV’s USB port.  
When attaching the stand to the TV set, place  
the screen facing down on a cushioned table or  
flat surface to protect the screen from scratches.  
Make sure that the screws are fastened tightly.  
(If they are not fastened securely enough, the TV  
may tilt forward after being installed.)  
Do not fasten the screws with excessive force;  
otherwise, they may be worn out and become  
loose.  
Use a certified cable with the HDMI logo  
attached. If you do not use a certified HDMI  
cable, the screen may not display or a  
connection error may occur.  
Recommended HDMI cable types (3 m or less)  
- High-Speed HDMI®/ TM cable  
Optional Extras  
- High-Speed HDMI ®/ TM cable with Ethernet  
Optional extras can be changed or modified for  
quality improvement without any notification.  
Contact your dealer for buying these items.  
These devices work only with certain models.  
The model name or design may be changed due to  
the manufacturer’s circumstances or policies.  
B
B
A
A
*A 10 mm (0.39 inches)  
*B 18 mm (0.7 inches)  
(Depending upon model)  
AG-F***  
Cinema 3D  
Glasses  
AG-F***DP  
Dual Play  
Glasses  
AN-VC550  
Smart Camera  
AN-MR6**  
LG Audio  
Magic Remote Device  
8
Maintenance  
Lifting and Moving the TV  
When moving or lifting the TV, read the following  
to prevent the TV from being scratched or  
damaged and for safe transportation regardless of  
its type and size.  
Cleaning Your TV  
Clean your TV regularly to keep it at peak  
performance and to extend the product’s lifespan.  
It is recommended to move the TV in the box or  
packing material that the TV originally came in.  
Before moving or lifting the TV, disconnect the  
power cord and all cables.  
CAUTION  
Before cleaning, turn the power off and  
disconnect the power cord and all other cables.  
When the TV is left unattended or unused for a  
long time, disconnect the power cord from the  
wall outlet to prevent possible damage from  
lightning or power surges.  
When holding the TV, the screen  
should face away from you to  
avoid damage.  
Screen, Frame, Cabinet, and Stand  
To remove dust or light dirt, wipe the surface with  
a dry, clean, and soft cloth.  
Hold the top and bottom of the TV frame firmly.  
Make sure not to hold the transparent part,  
speaker, or speaker grille area.  
To remove major dirt, wipe the surface with a soft  
cloth dampened in clean water or a diluted mild  
detergent. Then wipe immediately with a dry cloth.  
CAUTION  
Do not push, rub, or hit the surface with your  
fingernail or a sharp object, as this may result in  
scratches on the screen and image distortions.  
Do not use any chemicals, such as waxes,  
benzene, alcohol, thinners, insecticides, air  
fresheners, or lubricants, as these may damage  
the screen’s finish and cause discoloration.  
Do not spray liquid onto the surface. If water  
enters the TV, it may result in fire, electric shock,  
or malfunction.  
Use at least two people to move  
a large TV.  
When transporting the TV by  
hand, hold the TV as shown in the  
following illustration.  
Power Cord  
Remove the accumulated dust or dirt on the power  
cord regularly.  
When transporting the TV, do not expose the TV  
to jolts or excessive vibration.  
When transporting the TV, keep the TV upright;  
never turn the TV on its side or tilt towards the  
left or right.  
CAUTION  
Avoid touching the screen at all times, as this  
may result in damage to the screen.  
Do not place the product on the floor with its  
front facing down without padding. Failure to do  
so may result in damage to the screen.  
Do not move the TV by holding the cable  
holders, as the cable holders may break, and  
injuries and damage to the TV may occur.  
(Depending upon model)  
9
Using the Joystick Button  
Mounting on a Table  
(Depending upon model)  
(Image shown may differ from your TV.)  
(Image shown may differ from your TV.)  
1
Lift and tilt the TV into its upright position on a  
table.  
You can operate the TV by pressing the button or  
moving the joystick left, right, up, or down.  
- Leave a 10 cm (4 inches) (minimum) space  
from the wall for proper ventilation.  
10 cm  
(4 inches)  
Joystick Button  
10 cm  
10 cm  
10 cm  
Basic Functions  
When the TV is turned off,  
place your finger on the  
joystick button, press it once,  
and release it.  
When the TV is turned on,  
place your finger on the  
2
Connect the power cord to a wall outlet.  
CAUTION  
Power On  
Do not place the TV near or on sources of heat,  
as this may result in fire or other damage.  
joystick button, press it once  
Power Off for a few seconds, and release  
it. All running apps will close  
and any recording in progress  
will stop.  
Securing the TV to a Wall  
(optional)  
If you place your finger over  
(Depending upon model)  
Volume  
Control  
the joystick button and move  
it left or right, you can adjust  
the volume level.  
If you place your finger over  
Channels the joystick button and move  
Control  
it up or down, you can scroll  
through the saved channels.  
NOTE  
With your finger over the joystick button move  
it up, down, left, or right. Be careful not to press  
the joystick button. If you press the joystick  
button first, you may not be able to adjust  
the volume level and/or scroll through saved  
channels.  
1
Insert and tighten the eye-bolts, or TV brackets  
and bolts on the back of the TV.  
Adjusting the Menu  
- If there are bolts inserted at the eye-bolts  
position, remove the bolts first.  
When the TV is turned on, press the joystick button  
one time.  
You can adjust the menu items moving the joystick  
button up, down, left, or right.  
2
3
Mount the wall brackets with the bolts to the  
wall. Match the location of the wall bracket and  
the eye-bolts on the rear of the TV.  
Turns the power off.  
Accesses the quick settings.  
Connect the eye-bolts and wall brackets tightly  
with a sturdy rope or cable. Make sure to keep  
the rope parallel to the flat surface.  
Clears on-screen displays and returns to TV viewing.  
Changes the input source.  
10  
43UF7600  
49/55UF7600  
55UF8500  
55UF8600  
55UF9500  
55UG8700  
300 x 300  
Model  
CAUTION  
Make sure that children do not climb on or hang  
on the TV.  
200 x 200  
M6  
NOTE  
VESA (A x B)  
Standard screw  
Number of  
screws  
Wall mount  
M6  
Use a platform or cabinet that is strong and large  
enough to support the TV securely.  
Brackets, bolts, and ropes are optional. You can  
obtain additional accessories from your local  
dealer.  
4
4
MSW240  
LSW240B  
MSW240  
LSW350B  
bracket (optional)  
60/65UF7650  
60/65UF7690  
60/65UF7700  
60/65UF8500  
65UF8600  
70UF7650  
70/79UF7700  
Model  
Mounting on a Wall  
An optional wall mount can be used with your  
LG Television. Consult with your local dealer for  
a wall mount that supports the VESA standard  
used by your TV model. Carefully attach the wall  
mount bracket at the rear of the TV. Install the wall  
mount bracket on a solid wall perpendicular to the  
floor. If you are attaching the TV to other building  
materials, please contact qualified personnel to  
install the wall mount. Detailed instructions will  
be included with the wall mount. We recommend  
that you use an LG brand wall mount. When you do  
not use LG’s wall mount bracket, use a wall mount  
bracket where the device is adequately secured to  
the wall with enough space to allow connectivity  
to external devices.  
65UF9500  
65UG8700  
300 x 300  
M6  
600 x 400  
M8  
VESA (A x B)  
Standard screw  
Number of  
screws  
Wall mount  
4
4
LSW350B  
LSW640B  
bracket (optional)  
A
B
CAUTION  
Disconnect the power before moving or  
installing the TV. Otherwise electric shock may  
occur.  
Remove the stand before installing the TV on a  
wall mount by performing the stand attachment  
in reverse.  
If you install the TV on a ceiling or slanted wall,  
it may fall and result in severe injury. Use an  
authorized LG wall mount and contact the local  
dealer or qualified personnel. When using a  
third-party wall mount, it is not covered by the  
warranty.  
10 cm  
(4 inches)  
10 cm  
10 cm  
10 cm  
Do not overtighten the screws as this may cause  
damage to the TV and void your warranty.  
Use the screws and wall mounts that meet the  
VESA standard. Any damages or injuries by  
misuse or using an improper accessory are not  
covered by the warranty.  
Make sure to use screws and wall mounts that  
meet the VESA standard. Standard dimensions for  
the wall mount kits are described in the following  
table.  
NOTE  
Use the screws that are listed in the VESA  
standard screw specifications.  
The wall mount kit includes an installation  
manual and necessary parts.  
The wall mount bracket is optional. You can  
obtain additional accessories from your local  
dealer.  
The length of screws may differ depending upon  
the wall mount. Make sure to use the proper  
length.  
For more information, refer to the manual  
supplied with the wall mount.  
11  
When using the wall mounting bracket, apply  
the adhesive protective label to cover the  
unused stand openings. This will prevent the  
accumulation of dust and dirt. (Use only when  
provided with your particular model.)  
Connecting to an Antenna or  
Cable  
Connect an antenna, cable, or cable box to watch  
TV. The illustrations may differ from the actual  
items and an RF cable is optional.  
Provided Item  
CAUTION  
Make sure not to bend the copper wire of the RF  
cable.  
Adhesive protective label  
When removing the stand covers, insert a flat  
tool below the arrows. (e.g., a flat screwdriver)  
(For 79UF7700)  
Copper wire  
Complete all connections between devices, and  
then connect the power cord to the power outlet  
to prevent damage to your TV.  
NOTE  
Use a signal splitter to use 2 TVs or more.  
DTV Audio Supported Codec: MPEG,  
Dolby Digital.  
Connections (Notifications)  
Direct ULTRA HD broadcast is unavailable in  
areas without an ULTRA HD signal.  
This TV cannot receive ULTRA HD (3840 x 2160  
pixels) broadcasts directly because the related  
standards have not been confirmed. (Depending  
upon model)  
You can connect various external devices to the TV.  
Supported external devices are: HD receivers, DVD  
players, VCRs, audio systems, USB storage devices,  
PC, gaming devices, and other external devices.  
For more information on an external device’s  
connection, refer to the manual provided with  
each device.  
Other Connections  
NOTE  
If you record a TV program on a DVD recorder or  
VCR, make sure to connect the TV signal input  
cable to the TV through a DVD recorder or VCR.  
For more information about recording, refer to  
the manual provided with the connected device.  
The external device connections shown may  
differ slightly from illustrations in this manual.  
Connect external devices to the TV regardless  
about the order of the TV port.  
If you connect a gaming device to the TV, use the  
cable supplied with the gaming device.  
Refer to the external equipment’s manual for  
operating instructions.  
In PC mode, there may be noise associated  
with the resolution, vertical pattern, contrast,  
or brightness. If noise is present, change the PC  
output to another resolution, change the refresh  
rate to another rate, or adjust the brightness and  
contrast on the PICTURE menu until the picture  
is clear.  
Connect your TV to external devices. For the best  
picture and audio quality, connect the external  
device and the TV with the HDMI cable. Depending  
upon the model, a cable may not be provided.  
NOTE  
j
j
j PICTURE j  
HDMI ULTRA HD Deep Color:  
- On: Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)  
- Off: Support 4K @ 60 Hz (4:2:0)  
If the device connected to Input Port also  
supports ULTRA HD Deep Color, your picture  
may be clearer. However, if the device doesn’t  
support it, it may not work properly. In that case,  
connect the device to a different HDMI port or  
change the TV’s HDMI ULTRA HD Deep Color  
setting to Off.  
- This feature is available only on certain models  
which support HDMI ULTRA HD Deep Color.  
Depending upon the graphics card, some  
resolution settings may not allow the image to  
be positioned on the screen properly.  
12  
Magic Remote Functions  
(Image shown may differ from your TV.)  
When the message Magic remote battery is low.  
Change the battery. is displayed, replace the  
battery. To install batteries, open the battery cover,  
replace batteries (1.5 V AA) matching and  
ends to the label inside the compartment, and  
close the battery cover. Failure to match the correct  
polarities of the battery may cause the battery to  
burst or leak, resulting in fire, personal injury, or  
ambient pollution. Be sure to point the remote  
control at the remote control sensor on the TV.  
To remove the batteries, perform the installation  
actions in reverse.  
B
C
This remote uses infrared light. When in use, it  
should be pointed in the direction of the TV’s  
remote sensor.  
CAUTION  
Do not mix old and new batteries, as this may  
damage the remote control.  
B
VOL Adjusts the volume level.  
(MUTE) Mutes all sounds.  
By pressing and holding the button, VD  
function will be enabled.  
SAP (Secondary Audio Program) Feature can  
also be enabled by pressing the key.  
(Home) Accesses the Home menu.  
CH  
Scrolls through the saved channels.  
(Back) Returns to the previous screen.  
EXIT Clears all on-screen displays and returns to  
TV viewing.  
A
C
A
(up/down/left/right) Press the up, down,  
left or right button to scroll the menu. If you press  
buttons while the pointer is in use, the  
(POWER) Turns the TV on or off.  
(INPUT) Changes the input source.  
* Pressing and holding the  
displays all the lists of external inputs.  
(INPUT) button  
pointer will disappear from the screen and Magic  
Remote will operate like a general remote control.  
To display the pointer on the screen again, shake  
Magic Remote to the left and right.  
Number button Enters numbers.  
- (Dash) Inserts a dash between numbers such as  
2-1 and 2-2.  
Wheel (OK) Press the center of the Wheel  
button to select a menu. You can change channels  
by using the Wheel button.  
LIST Accesses the saved channel list.  
INFO Shows information on the current program.  
(Q. Settings) Accesses the quick settings.  
* Pressing and holding the (Q. Settings) button  
displays the Advanced menu.  
13  
How to Use Magic Remote  
(Screen Remote) Displays the Screen Remote.  
* Accesses the Universal Control Menu in some regions.  
Used for viewing 3D video. (For 3D models)  
Shake the Magic Remote slightly to  
the right and left or press  
(Home), (INPUT),  
buttons  
to make the pointer appear on the  
screen. (In some TV models, the  
pointer will appear when you turn the  
Wheel button.)  
If the pointer has not been used for  
a certain period of time or Magic  
Remote is placed on a flat surface,  
then the pointer will disappear.  
If the pointer does not move as you  
wish, shake Magic Remote to the left  
and right. The pointer will move to  
the center of the screen.  
(Voice recognition) Network connection is  
required to use the voice recognition function.  
1. Press the voice recognition button.  
2. Speak when the voice display window appears  
on the TV screen.  
Use the Magic Remote no further than 10 cm  
(4 inches) from your face.  
The voice recognition may fail when you speak  
too fast or too slowly.  
The recognition rate may vary depending upon  
the user’s characteristics (voice, pronunciation,  
intonation, and speed) and the environment  
(noise and TV volume).  
The Magic Remote depletes batteries  
faster than a normal remote due to  
the additional features.  
CAPTION Activates or deactivates the subtitles.  
Color buttons These access special functions in  
Precautions to Take When Using the  
Magic Remote  
some menus.  
(
Red,  
Green,  
Yellow,  
Blue)  
Use the Magic Remote within the maximum  
communication distance (10 m, 32.8 ft). Using  
the remote control beyond this distance, or  
with an object obstructing it, may cause a  
communication failure.  
A communication failure may occur due to  
nearby devices. Electrical devices such as a  
microwave oven or wireless LAN product may  
cause interference, as these use the same  
bandwidth (2.4 GHz) as the Magic Remote.  
The Magic remote may be damaged or may  
malfunction if it is dropped or receives a heavy  
impact.  
Take care not to bump into nearby furniture or  
other people when using the Magic Remote.  
Manufacturer and installer cannot provide  
service related to human safety as the  
applicable wireless device has possibility of  
electromagnetic interference.  
Registering Magic Remote  
How to register the Magic Remote  
To use the Magic Remote, first pair it  
with your TV.  
1 Put batteries into the Magic Remote  
and turn the TV on.  
2 Point the Magic Remote at your TV  
and press the Wheel (OK) on the  
remote control.  
(Wheel)  
If the TV fails to register the Magic  
Remote, try again after turning the TV  
off and back on.  
How to deregister the Magic Remote  
Press the  
(Back) and  
(Home)  
It is recommended that an Access Point (AP) be  
located more than 1 m (3.28 ft.) away from the  
TV. If the AP is installed closer than 1 m (3.28 ft.),  
the Magic Remote may not perform as expected  
due to frequency interference.  
buttons at the same time, for five  
seconds, to unpair the Magic Remote  
with your TV.  
Pressing and holding the  
EXIT button will let you cancel and  
re-register Magic Remote at once.  
(Back)  
(Home)  
14  
Licenses  
Specifications  
Supported licenses may differ by model.  
For more information about licenses, visit  
Product specifications may be changed without  
prior notice due to upgrade of product functions.  
Television System  
ATSC, NTSC-M, 64 & 256 QAM  
Program Coverage  
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135  
External Antenna Impedance  
Open Source Software Notice  
Information  
75 Ω  
Environment Condition  
Operating Temperature  
0 °C to 40 °C (32 °F to 104 °F)  
Operating Humidity  
Less than 80 %  
To obtain the source code under GPL, LGPL, MPL,  
and other open source licenses, that is contained  
in this product, please visit http://opensource.lge.  
com.  
In addition to the source code, all referred license  
terms, warranty disclaimers and copyright notices  
are available for download.  
LG Electronics will also provide open source code  
to you on CD-ROM for a charge covering the cost  
of performing such distribution (such as the cost of  
media, shipping, and handling) upon email request  
to [email protected]. This offer is valid for three  
(3) years from the date on which you purchased  
the product.  
Storage Temperature  
- 20 °C to 60 °C (-4 °F to 140 °F)  
Storage Humidity  
Less than 85 %  
Wireless Module (LGSBW41)  
Specifications  
(For UF7600, UF7650, UF7690, UF7700, UF8500,  
UF8600, UG8700 series)  
Wireless LAN  
Bluetooth  
Bluetooth  
Standard IEEE 802.11a/b/g/n Standard Version  
Troubleshooting  
4.0  
2400 to 2483.5 MHz  
5150 to 5250 MHz  
5725 to 5850 MHz  
2400 to  
2483.5  
MHz  
Frequency  
range  
Frequency  
range  
Cannot control the TV with the remote control.  
- Check if anything such as tape has been placed  
over the receiver.  
- Check if there is any obstacle between the  
product and the remote control.  
- Replace the batteries with new ones.  
No image display and no sound is produced.  
- Check if the product is turned on.  
- Check if the power cord is connected to a wall  
outlet.  
- Check if there is a problem in the wall outlet by  
connecting other products.  
The TV turns off suddenly.  
- Check the power control settings. The power  
supply may be interrupted.  
- Check if the Sleep Timer / Timer Power Off  
feature is activated in the TIMERS settings.  
- If there is no signal while the TV is on, the TV  
will turn off automatically after 15 minutes of  
inactivity.  
802.11a: 11.5 dBm  
802.11b: 11 dBm  
802.11g: 10.5 dBm Output  
802.11n - 2.4 GHz: power  
11 dBm  
Output  
power  
(Max.)  
10 dBm or  
Lower  
(Max.)  
802.11n - 5 GHz:  
12.5 dBm  
Because band channel used by the country could  
be different, the user can not change or adjust the  
operating frequency and this product is set for the  
regional frequency table.  
This device should be installed and operated with  
minimum distance 20 cm (7.8 inches) between  
the device and your body. And this phrase is for  
the general statement for consideration of user  
environment.  
Contains FCC ID: BEJLGSBW41 /  
Contains IC: 2703H-LGSBW41  
15  
Wireless Module (LGSBW51)  
Specifications  
(For UF9500 series)  
Wireless LAN  
Bluetooth  
IEEE 802.11a/b/g/n/  
ac  
Bluetooth  
Version 4.0  
Standard  
Standard  
2400 to 2483.5 MHz  
5150 to 5250 MHz  
5725 to 5850 MHz  
2400 to  
2483.5  
MHz  
Frequency  
range  
Frequency  
range  
802.11a: 15 dBm  
802.11b: 17 dBm  
802.11g: 15 dBm  
802.11n - 2.4 GHz: Output  
15 dBm  
802.11n - 5 GHz:  
15 dBm  
Output  
power  
(Max.)  
10 dBm or  
Lower  
power  
(Max.)  
802.11ac - 5 GHz :  
15 dBm  
Because band channel used by the country could  
be different, the user can not change or adjust the  
operating frequency and this product is set for the  
regional frequency table.  
This device should be installed and operated with  
minimum distance 20 cm (7.8 inches) between  
the device and your body. And this phrase is for  
the general statement for consideration of user  
environment.  
Contains FCC ID: BEJLGSBW51 /  
Contains IC: 2703H-LGSBW51  
16  
CHILD SAFETY:  
PROPER TELEVISION PLACEMENT MATTERS  
THE CONSUMER ELECTRONICS INDUSTRY CARES  
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to  
making home entertainment safe and enjoyable.  
• As you enjoy your television, please note that all televisions – new and old- must be supported on  
proper stands or installed according to the manufacturer’s recommendations. Televisions that  
are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,  
may fall over, resulting in injury.  
TUNE IN TO SAFETY  
ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.  
ALWAYS read and follow all instructions for proper use of your television.  
NEVER allow children to climb on or play on the television or the furniture on which the television  
is placed.  
NEVER place the television on furniture that can easily be used as steps, such as a chest of  
drawers.  
ALWAYS install the television where it cannot be pushed, pulled over or knocked down.  
ALWAYS route cords and cables connected to the television so that they cannot be tripped  
over, pulled or grabbed.  
WALL OR CEILING MOUNT YOUR TELEVISION  
ALWAYS contact your retailer about professional installation if you have any doubts about your  
ability to safely mount your television.  
ALWAYS use a mount that has been recommended by the television manufacturer and has a  
safety certification by an independent laboratory (such as UL, CSA, ETL).  
ALWAYS follow all instructions supplied by the television and mount manufacturers.  
ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.  
Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder  
block construction. If you are unsure, contact a professional installer.  
Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount  
installation.  
MOVING AN OLDER TELEVISION TO A NEW PLACE IN  
YOUR HOME  
• Many new television buyers move their older CRT televisions into a secondary room after the  
purchase of a flat-panel television. Special care should be made in the placement of older CRT  
televisions.  
ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size  
and weight.  
NEVER place your older CRT television on a dresser where children may be tempted to use the  
drawers to climb.  
ALWAYS make sure your older CRT television does not hang over the edge of your furniture.  
CE.org/safety  
Declaration of Conformity  
Trade Name: LG  
Model: 43UF7600-UJ, 49UF7600-UJ, 55UF7600-UJ,  
60UF7650-UJ, 65UF7650-UJ, 70UF7650-UJ,  
60UF7690-UH, 65UF7690-UH, 60UF7700-UJ,  
65UF7700-UJ, 70UF7700-UJ, 79UF7700-UB,  
55UF8500-UB, 60UF8500-UB, 65UF8500-UB,  
55UF8600-UF, 65UF8600-UF, 55UF9500-UA,  
65UF9500-UA, 55UG8700-UA, 65UG8700-UA  
Responsible Party: LG Electronics Inc.  
Address: 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A  
TEL: 201-266-2534  
LG Customer Information Center  
1-800-243-0000  
1-888-865-3026  
1-888-542-2623  
USA, Consumer User  
USA, Commercial User  
CANADA  
The model and serial numbers of the TV are located on  
the back and on one side of the TV. Record them below  
should you ever need service.  
Register your product Online!  
MODEL  
SERIAL  
ENGLISH  
Easy Setup Guide  
LED TV  
Please read this manual carefully before operating your set and retain it for future reference.  
79UF7700  
ESPAÑOL  
Guía Rápida de Configuración  
Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.  
FRANÇAIS  
Guide de configuration rapide  
Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour pouvoir vous y reporter ultérieurement.  
X 4  
(M4 X L16)  
AA  
P/No : MFL68684904 (1503-REV00)  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
Read Safety and Reference.  
Leer Seguridad y Consultas.  
Lisez Sécurité et références.  
i
?
2
3
1
A
1
B
4
ENGLISH  
Image shown may differ from your TV.  
ESPAÑOL La imagen puede ser diferente a la de su televisor.  
FRANÇAIS Cette illustration peut ne pas correspondre à votre téléviseur.  
2
A
A
A
B
B
OPTICAL  
DIGITAL  
LAN  
AUDIO OUT/  
H/P OUT  
AUDIO OUT  
SVC ONLY  
PC-AUDIO IN  
ANTENNA/  
CABLE IN  
VIDEO/Y  
PB  
PR  
L/MONO AUDIO  
R
COMPONENT IN / AV IN  
(MONO)  
VIDEO  
AUDIO  
VIDEO  
AUDIO  
3
4
5
2
4
1
3
79UF7700  
(79UF7700-UB)  
ENGLISH  
MODELS  
With stand  
1,770.4 x 1,083.2 x 317 (mm)  
69.7 x 42.6 x 12.4 (inches)  
1,770.4 x 1,025.2 x 59.5 (mm)  
69.7 x 40.3 x 2.3 (inches)  
54.5 kg (120.1 lbs)  
Dimensions (W x H x D)  
Without stand  
With stand  
Weight  
Without stand  
52.4 kg (115.5 lbs)  
Power requirement  
AC 120 V ~ 50/60 Hz  
2.9 A / 290 W  
Current value / Power consumption  
MODELOS  
MODÈLES  
79UF7700  
(79UF7700-UB)  
ESPAÑOL  
FRANÇAIS  
Con base  
1 770,4 x 1 083,2 x 317 (mm)  
69,7 x 42,6 x 12,4 (pulgadas/po)  
1 770,4 x 1 025,2 x 59,5 (mm)  
69,7 x 40,3 x 2,3 (pulgadas/po)  
Dimensiones  
(Ancho x altura x profundidad)  
Avec support  
Sin base  
Dimensions (L x H x P)  
Sans support  
Con base  
Peso  
54,5 kg (120,1 libras/lb)  
52,4 kg (115,5 libras/lb)  
AC 120 V ~ 50/60 Hz  
2,9 A / 290 W  
Avec support  
Sin base  
Poids  
Sans support  
Potencia requerida  
Alimentation  
Corriente de consumo / Consumo de la potencia  
Valeur courante / Consommation électrique  
(For USA and Canada only)  
(Para Estados Unidos y Canadá)  
(Pour les États-Unis et le Canada)  
Ce produit est conforme aux normes  
This product qualifies for ENERGY STAR in  
the factory default (Home configuration)  
setting. Changing the factory default  
ENERGY STAR lorsque le « réglage d’usine  
par défaut (Résidentiel) » est sélectionné.  
Modifier les réglages d’usine par défaut ou  
settings or enabling other features may  
increase power consumption that could exceed the  
limits necessary to quality for ENERGY STAR. Refer to  
ENERGYSTAR.gov for more information on the  
ENERGY STAR program.  
activer d’autres fonctionnalités augmente la  
consommation d’énergie qui pourrait alors dépasser les  
limites de la qualification Energy Star. Consultez le site  
ENERGYSTAR.gov pour en savoir plus au sujet du  
programme ENERGY STAR.  

Watts Radiant Wm100sm User Manual
Sanyo 09ks71 User Manual
Samsung Commercial Splittype Series Ns026nhxea User Manual
Panasonic Dp 8060 User Manual
Lexmark Gd1 User Manual
HP 5900 User Manual
EPSON CMID 2260 User Manual
BROTHER FAX 275 User Manual
ACER ASPIRE SA20 User Manual
3COM 8814 User Manual