KENWOOD KDC X395 User Manual
KDC-BT648U  
KDC-X695  
KDC-X395  
KDC-348U  
CIND-SRETCERIVUERCTION MANUAL  
AMMOPLID-TUENEDR ’LEECMTEUPRLDOE CID  
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM  
MANUAL DE INSTRUCCIONES  
Take the time to read through this instruction manual.  
Familiarity with installation and operation procedures will help you obtain the best performance from  
your new CD-receiver.  
For your records  
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the  
space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for  
information or service on the product.  
Model KDC-BT648U/ KDC-X695/ KDC-X395/ KDC-348U Serial number  
US Residents Only  
Register Online  
Register your Kenwood product at www.Kenwoodusa.com  
© 2010 Kenwood Corporation All Rights Reserved.  
B64-4798-10/01 (KW/K0)  
Safety  
WARNING  
Stop the car before operating the unit.  
Important to know...  
■
To prevent a short circuit, never put or leave  
any metallic objects (such as coins or metal  
tools) inside the unit.  
Caution: Adjust the volume so that you can  
■
hear sounds outside the car. Driving with  
the volume too high may cause an accident.  
Condensation: When the car is air-  
■
conditioned, moisture may collect on the  
laser lens. This may cause disc read errors. In  
this case, remove the disc and wait for the  
moisture to evaporate.  
■
■
The “AAC” logo is a trademark of Dolby  
Laboratories.  
The Bluetooth word mark and logos  
are owned by the Bluetooth SIG, Inc.  
and any use of such marks by Kenwood  
Corporation is under license. Other  
trademarks and trade names are those of  
their respective owners.  
Ready to receive HD Radio™ broadcasts  
when connected to the KTC-HR300/ KTC-  
HR200/ KTC-HR100TR, sold separately.  
“Made for iPod” and “Made for iPhone”  
mean that an electronic accessory has  
been designed to connect specifically  
to iPod or iPhone, respectively, and has  
been certified by the developer to meet  
Apple performance standards. Apple is  
not responsible for the operation of this  
device or its compliance with safety and  
regulatory standards. Please note that the  
use of this accessory with iPod or iPhone  
may affect wireless performance.  
■
The illustrations in this manual are examples  
used to explain more clearly how the  
controls are used. Therefore, what appears  
on the illustrations may differ from what  
appears on the actual equipment.  
If you experience problems during  
installation, consult your Kenwood dealer.  
■
■
■
■
When you purchase external components,  
check with your Kenwood dealer to make  
sure that they work with your model and in  
your area.  
Maintenance  
Cleaning the unit: Wipe off the dirt on the  
panel with a dry silicon or soft cloth. Failure  
to observe this precaution may result in  
damage to the monitor or unit.  
Cleaning the connector: Wipe off dirt on  
the connector of the unit and faceplate. Use  
a cotton swab or cloth.  
■
■
iPhone, iPod, iPod classic, iPod nano, and  
iPod touch are trademarks of Apple Inc.,  
registered in the U.S. and other countries.  
iTunes is a trademark of Apple Inc.  
This symbol mark indicates  
that Kenwood manufactured  
this product so as to decrease  
harmful influence on the  
environment.  
English 3  
Preparation  
How to attach/detach the faceplate  
How to prepare the remote  
controller (RC-405)  
When you use the remote controller for the  
1
first time, pull out the insulation sheet.  
1
Insulation sheet  
2
2
■
Do not expose the faceplate to direct  
sunlight, excessive heat, or humidity. Also  
avoid places with too much dust or the  
possibility of water splashing.  
If the effectiveness of the remote  
controller decreases, replace the battery.  
■
Keep the faceplate in its casing while  
detached.  
The faceplate is a precision piece of  
equipment and can be damaged by shocks  
or jolts.  
To prevent deterioration, do not touch the  
4
3
2
■
1
■
terminals of the unit and faceplate with your  
fingers.  
¤
Caution:  
■
Do not set the remote control in hot places  
How to reset your unit  
such as on the dashboard.  
Lithium battery.  
If this unit fails to operate  
properly, press the reset  
button.  
■
Danger of explosion if the battery is  
incorrectly replaced. Replace only with the  
same or equivalent type.  
1
The unit returns to factory  
settings when the reset  
2
■
The battery pack or batteries shall not be  
button is pressed.  
exposed to excessive heat such sunshine,  
fire or the like.  
Keep battery out of reach of children and in  
3
■
original package until ready to use. Dispose  
of used batteries promptly. If swallowed  
contact physician immediately.  
Reset button  
CALIFORNIA, USA ONLY  
This product contains a CR Coin Cell Lithium  
Battery which contains Perchlorate Material –  
special handling may apply.  
See www.dtsc.ca.gov/hazardouswaste/  
perchlorate  
4 English  
Getting Started  
Canceling the display  
demonstration  
Adjusting the clock  
1 Press the volume knob to enter  
[FUNCTION] mode.  
The display demonstration is always turned  
on unless you cancel it.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select [CLOCK],  
then press to enter.  
When you turn on the power (or after you  
reset the unit), the display shows:  
[CANCEL DEMO] \ [PRESS] \ [VOLUME 4 Turn the volume knob to select [CLOCK  
KNOB]  
ADJUST], then press to enter.  
Clock hour flashes on the display.  
1 Press the volume knob.  
[YES] is selected as the initial setup.  
2 Press the volume knob again to confirm.  
[DEMO OFF] appears.  
5 Turn the volume knob to adjust the hour,  
then press to enter minute adjustment.  
Clock minutes flashes on the display.  
6 Turn the volume knob to adjust the  
minute, then press to confirm.  
■
If no operation is done for about 15 seconds  
or if you turn the volume knob to select  
[NO] in step 2, [DEMO MODE] appears and  
the display demonstration starts.  
Press 4 / ¢ to move between the  
hour and minute adjustment.  
7 Hold  
to finish the procedure.  
Setting the demonstration mode  
1 Press the volume knob to enter  
[FUNCTION].  
2 Turn the volume knob to select [DEMO  
MODE], then press to enter.  
3 Turn the volume knob to select [ON] or  
[OFF].  
Initial settings before operations  
1 Press SRC to enter [STANDBY] mode.  
2 Press the volume knob to enter  
[FUNCTION] mode.  
3 Turn the volume knob to select [INITIAL  
SET], then press to enter.  
If [ON] is selected, display demonstration  
starts if no operation is done for about 20  
seconds.  
4 Turn the volume knob to make a  
selection, then press to confirm.  
See table below for selection.  
4 Hold  
to finish the procedure.  
5 Hold  
to finish the procedure.  
Item  
Selectable setting (Preset: *)  
PRESET TYPE NORMAL *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ;  
MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ AM) and  
another Satellite Radio Tuner.  
KEY BEEP  
ON */ OFF: Activates/deactivates the keypress tone.  
BUILT-IN AUX ON1 *: Outputs sound of the connected external component through the car speakers when “AUX” is selected as the  
source. ; ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When  
you turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn the  
volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.  
CD READ  
1*: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to play as a music CD. No sound can  
be heard if an audio file disc is played.  
SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.  
F/W UP xx.xx YES: Starts upgrading the firmware. ; NO *: Cancels (upgrading is not activated).  
For details on how to update the firmware, see: www.kenwood.com/cs/ce/  
English 5  
Basic Operations  
Loading slot  
Remote sensor  
■
Do not expose to bright sunlight.  
Ejects the disc  
Volume knob  
Display window  
Detaches the faceplate  
The following indicator lights up when...  
ST: A stereo broadcast is received.  
RDS: Radio Data System service is available.  
TI: Traffic Information function is turned on.  
IN: A disc is in the unit.  
ATT: The sound attenuates.  
EQ: [SYSTEM Q] is set to an EQ mode other  
than [NATURAL]. (page 28)  
B.BOOST: [BASS BOOST] is set to [1] or [2].  
(page 28)  
USB terminal  
Auxiliary input jack  
: Indicates that the Music Search mode is  
selected now.  
BT: Bluetooth cell-phone connection status.  
Slide open the cover  
The illustration and button names used  
for explanation in this manual are of  
KDC-BT648U/ KDC-X695 (unless mentioned  
otherwise).  
Refer to the table below for the difference:  
KDC-BT648U/ KDC-X695  
KDC-X395/ KDC-348U  
6 English  
When you press or hold the following button(s)...  
Remote  
controller  
Main unit  
General operation  
■
Turns on.  
—
■
Turns off if pressed and held.  
Selects the available sources (TUNER, USB or iPod, CD, AUX,  
STANDBY), if the power is turned on.  
• If the source is ready, playback also starts. “iPod” and “CD” are  
selectable only when an iPod is connected or a disc is loaded.  
Adjusts the volume level.  
SRC  
SRC  
VOLud  
Volume knob  
(turn)  
5 / ∞ Selects items.  
ENT 38 Confirms selection.  
Volume knob  
(press)  
—
Enters [FUNCTION] settings.  
■
Selects the FM bands (FM1/ FM2/ FM3) or AM.  
Selects the next folder. (Press *AM– on remote controller to select  
the previous folder.)  
*AM– /  
#FM+  
■
BAND  
6 (38)  
ENT 38 Pauses/resumes playback of a disc/ USB device/ iPod.  
■
Searches for radio station.  
Selects track/file.  
Fast-forwards/reverses tracks/files if pressed and held.  
4/  
+¢  
■
4 / ¢  
■
■
Changes the display information.  
Scrolls the display information if pressed and held.  
Enters clock adjustment mode directly (page 5) if pressed and held  
■
SCRL DISP  
—
■
while in clock display screen.  
KDC-BT648U/ KDC-X695 only:  
■
Enters Bluetooth mode. (page 15)  
Press to answer an incoming call.  
■
■
—
—
Enters Bluetooth easy pairing mode if pressed and held. (page 18)  
KDC-X395/ KDC-348U only:  
■
Selects “iPod” source.  
Switches the controlling terminal (HANDS ON/ HANDS OFF) for  
iPod  
■
iPod playback if pressed and held. (page 13)  
Enters [AUDIO CONTROL] settings directly.  
Attenuates the sound.  
—
—
AUD  
ATT  
• To return to the previous level, press the button again.  
Returns to the previous item.  
Exit from setting mode.  
EXIT  
• Press and hold on the main unit will also exit from the setting  
mode.  
English 7  
Muting upon the reception of a phone call (KDC-X395/ KDC-348U only)  
To use this feature, connect the MUTE lead to your telephone using a commercial telephone  
accessory. (See “Installation Manual” on a separate volume.)  
When a call comes in, “CALL” appears.  
■
The audio system pauses.  
To continue listen to the audio system during a call, press SRC. “CALL” disappear and the  
■
audio system resumes.  
When a call ends, “CALL” disappear.  
■
The audio system resumes.  
Listening to the Radio  
■
Hold for about 2 seconds to memorize the current station or the selected Program  
Type. (Refer to [PTY SEARCH] on the table below to select the Program Type.)  
Press briefly to recall memorized station (or Program Type after entering the PTY  
■
search mode).  
Adjust [SETTINGS] mode settings  
While listening to the radio...  
1 Press the volume knob to enter  
[FUNCTION] mode.  
1 Press SRC to select “TUNER”.  
2 Press BAND repeatedly to select a band  
(FM1/ FM2/ FM3/ AM).  
3 Press 4 / ¢ to search for a station.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to make a  
selection, then press to confirm.  
See table below for selection.  
Using the remote controller (RC-405)  
#FM+ / *AM– : Selects band.  
4 / +¢  
1 – 6  
: Selects station.  
: Selects preset station.  
4 Hold  
to finish the procedure.  
Item  
Selectable setting (Preset: *)  
SEEK MODE  
Selects the tuning mode for 4 / ¢ buttons.  
AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. ;  
MANUAL: Manually search for a station.  
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ; NO *: Cancels (automatic memorizing is  
not activated). (Selectable only if [NORMAL] is selected for [PRESET TYPE].) (page 5)  
TI  
ON: The traffic information automatically when the traffic bulletin starts. ; OFF *: Cancels. (Not applicable if “AM”  
is selected)  
8 English  
Item  
MONO SET  
PTY SEARCH  
Selectable setting (Preset: *)  
ON: Improves the FM reception (but the stereo effect may be lost). ; OFF *: Cancels (stereo effect resumes).  
Selects the available Program Type (page 9). Then, press  
4
/
¢
to start searching.  
■
[TI] is selectable only when the source is “FM”. If other playback source is selected, these settings are selectable under [TUNER SET]  
item. (page 29)  
■
Available Program Type:  
SPEECH; MUSIC; NEWS; INFORM; SPORTS; TALK; ROCK; CLS (classic) ROCK; ADLT (adult) HIT; SOFT RCK (rock); TOP 40; COUNTRY;  
OLDIES; SOFT; NOSTALGA; JAZZ; CLASSICL; R & B; SOFT R&B; LANGUAGE; REL (religious) MUSC; REL (religious) TALK; PERSNLTY  
(personality); PUBLIC; COLLEGE; WEATHER  
The unit will search for the Program type categorized under [SPEECH] or [MUSIC] if selected.  
[SPEECH] : Roman typeface item. ; [MUSIC] : Italic typeface item.  
■
■
The Radio Data System feature won’t work where the service is not supported by any  
broadcasting station.  
If the volume is adjusted during reception of traffic information, the adjusted volume is  
memorized automatically. It will be applied the next time Traffic Information function is  
turned on.  
Listening to the other external  
components  
Preparation : Make sure [ON1] or [ON2] is selected for [BUILT-IN AUX]. (page 5)  
1 Press SRC to select “AUX”.  
2 Turn on the external component and  
Auxiliary input jack  
start playing.  
3 Turn the volume knob to adjust the  
volume.  
3.5 mm (1/8”) stereo mini plug  
(commercially available)  
Portable audio device  
(commercially available)  
English 9  
Listening to a Disc/ USB device/ iPod  
Ejects the disc.  
(“NO DISC” appears and “IN” indicator goes off.)  
■
Press to select track/file.  
Hold to fast-forwards/reverses.  
USB terminal  
■
Press to pause. Press again  
to resume playback.  
■
■
Press to select next folder of Audio  
File/iPod.  
Press to select next disc of CD changer.  
Start playing a disc  
1 Press SRC to turn on the power.  
2 Insert a disc into the loading slot.  
Playback starts automatically.  
Apple iPod  
(commercially available)  
Start playing a USB device or iPod  
1 Press SRC to turn on the power.  
2 Slide open the cover.  
3 Connect a USB device or iPod to the USB  
terminal.  
KCA-iP102  
(optional accessory)  
The source automatically switches, and  
playback starts.  
Removing the USB device or iPod  
1 Press SRC to select a source other than  
“USB” or “iPod”.  
2 Remove the USB device or iPod.  
Start playing the disc changer  
1 Press SRC to turn on the power.  
2 Press SRC to select “CD CHANGER”.  
USB device  
(commercially available)  
CA-U1EX  
(optional accessory)  
10 English  
Selecting Repeat Play  
Press number button 4 (REP) repeatedly  
to make a selection.  
Selecting a folder/track/file  
• Not available if disc changer playback is  
selected.  
Audio CD : TRACK REPEAT, REPEAT OFF  
Audio File :  
1 Press to enter Music Search mode.  
“SEARCH” appears, then the current file  
name appears on the display.  
2 Turn the volume knob to select a folder/  
track/ file, then press to confirm.  
FILE REPEAT, FOLDER REPEAT, REPEAT OFF  
iPod :  
FILE REPEAT, REPEAT OFF  
CD changer : TRACK REPEAT, DISC REPEAT,  
REPEAT OFF  
■
To skips songs, press 4/ ¢. Holding  
4/ ¢ skips songs at 10% regardless of  
the setting made. (page 13)  
Selecting Random Play  
This operation is effective only for the iPod  
or Kenwood Music Editor media.  
To return to the root folder (audio file), top  
Press number button 3 (ALL RDM)  
repeatedly to make a selection.  
Audio CD : DISC RANDOM, RANDOM OFF  
Audio File/ iPod :  
FOLDER RANDOM, RANDOM OFF  
CD changer : DISC RANDOM, RANDOM OFF  
■
menu (iPod) or first track (audio CD), press  
BAND.  
■
To return to the previous folder, press  
To cancel the Music Search mode, press and  
hold  
< or > on the display indicates that  
preceded/next item is available.  
.
■
.
All Random Play  
■
Press and hold number button  
3 (ALL RDM).  
Pressing this button again plays songs in  
the normal mode starting.  
Audio File/ iPod :  
Alphabet Search for iPod  
1 Press to enter Music Search mode.  
“SEARCH” appears.  
2 Turn the volume knob to select a  
category, then press to confirm.  
3 Press again to enter alphabet search  
mode.  
ALL RANDOM, RANDOM OFF  
Changes the iPod browsing item to “songs”.  
■
Selecting Magazine Random Play  
Press number button 5 repeatedly to  
make a selection.  
“SEARCH <– – –>” appears.  
4 Turn the volume knob to select the  
character to be searched for.  
5 Press 4 / ¢ to move to the entry  
position.  
You can enter up to three characters.  
6 Press the volume knob to start searching.  
After this step, see step 2 of <Selecting a  
folder/track/file> (page 11) to select a song.  
CD changer : MGZN (magazine) RANDOM,  
RANDOM OFF  
Selecting Scan Play  
Press number button 2 (SCAN)  
repeatedly to make a selection.  
Audio CD : TRACK SCAN, SCAN OFF  
Audio File : FILE SCAN, SCAN OFF  
CD changer : TRACK SCAN, SCAN OFF  
■
To return to the Music Search mode, press  
.
■
If scan play is selected, the unit starts  
■
To cancel the Music Search mode, press and  
playing the first 10-second intro of the  
music in the disc/current folder.  
If “SCAN OFF” is selected, the unit resumes  
normal play of the current song.  
hold  
.
■
A longer searching time is required if there  
are many songs or playlists in the iPod.  
Continued to next page  
English 11  
■
■
To search for a character other than A to Z  
and 0 to 9, enter only “ * ”.  
The article (a, an, the) of songs name will be  
skipped during search.  
My Playlist for iPod  
Registering songs in the playlist  
1 Select and play the song you want to  
register. (page 11)  
2 Press and hold number button  
5 (MEMO MY LIST) to register.  
“## STORED” (registration number) appears.  
You can register up to 10 songs. “MEMORY  
FULL” appears, if you try to register the  
eleventh song.  
If you attempt to register a song from  
a different iPod, “NO INFO” followed by  
“MPLIST DELETE” appears.  
Direct Music Search using the  
remote controller (RC-405)  
• Not available if Random Play, Scan Play,  
KENWOOD Music Editor media, iPod playback  
is selected.  
1 Press DIRECT to enter Direct Music  
Search mode.  
“– – –” appears.  
2 Press the number buttons to enter the  
track number.  
■
To delete the playlist, turn the volume knob  
to select “YES”, then press to confirm.  
You can also register the song displayed in  
3 Press 4 / +¢ to search for the music.  
■
■
To cancel the Direct Music Search mode,  
the Music Search mode by following the  
same procedure.  
Do not register Podcasts.  
press  
.
■
Direct Disc Search using the remote  
controller (RC-405)  
• Only when the source is CD changer.  
• Not available if Random Play, Scan Play is  
selected.  
1 Press DIRECT to enter Direct Disc Search  
mode.  
“– –” appears.  
2 Press the number buttons to enter the  
disc number.  
Playing a song on the playlist  
1 Press number button  
5 (MEMO MY LIST) to display the playlist.  
“MY PLAYLIST” appears.  
2 Turn the volume knob to select the song  
you want, then press to confirm.  
■
Random play cannot be performed during  
playback of a song in the playlist.  
3 Press #FM+ / *AM– to search for the disc.  
To cancel the Direct Disc Search mode,  
Deleting a song on the playlist  
1 Press number button 5 (MEMO MY LIST)  
to display the playlist.  
■
press  
.
“MY PLAYLIST” appears.  
Using the remote controller (RC-405)  
In playback mode:  
#FM+ / *AM– : Selects folder/disc.  
2 Turn the volume knob to select the song  
you want to delete, then press and hold  
the volume knob.  
3 Turn the volume knob to select [DELETE  
ONE] or [DELETE ALL], then press to  
confirm.  
Select “DELETE ALL” to delete all the songs  
in the playlist.  
4 Turn the volume knob to select [YES],  
then press to confirm.  
4 / +¢  
: Selects track/file.  
: Pauses/resumes playback.  
ENT 38  
In Music Search mode:  
ENT 38 : Confirms selection.  
5 / ∞  
: Selects folder/file/track.  
: Returns to the previous folder.  
“COMPLETED” appears.  
12 English  
iPod control by Hand mode  
Press number button 1 (iPod) repeatedly  
to make a selection.  
Handling discs  
Do not touch the recording surface of  
■
the disc.  
KDC-X395 / KDC-348U  
■
Do not stick tape etc. on the disc, or use a  
Press and hold iPod repeatedly to make  
a selection.  
HANDS ON :  
disc with tape stuck on it.  
Do not use any accessories for the disc.  
Clean from the center of the disc and  
move outward.  
■
■
Control iPod from the iPod.  
This mode is not compatible with music  
■
■
Clean the disc with a dry silicon or soft  
information display. The display will show  
“iPod MODE”.  
HANDS OFF: Control iPod from the unit.  
cloth. Do not use any solvents.  
When removing discs from this unit, pull  
them out horizontally.  
Remove the rims from the center hole  
■
■
Adjust [SETTINGS] mode settings  
While listening to an iPod or KENWOOD Music  
Editor media ...  
1 Press the volume knob to enter  
[FUNCTION] mode.  
and disc edge before inserting a disc.  
Discs that cannot be used  
This unit can only play the CDs with:  
■
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to make a  
selection, then press to confirm.  
See the following table for selection.  
■
Discs that are not round.  
Discs with coloring on the recording  
surface or discs that are dirty.  
You cannot play a Recordable/ReWritable  
disc that has not been finalized. (For the  
finalization process refer to your disc  
writing software, and your disc recorder  
instruction manual.)  
3-inch CD cannot be used. Attempt  
to insert using an adapter can cause  
malfunction.  
■
■
4 Hold  
to finish the procedure.  
Item  
Selectable setting (Preset: *)  
SKIP SEARCH 0.5% */ 1%/ 5%/ 10%: Sets the ratio of skip  
when searching for a song in Music Search  
mode.  
■
MPLIST  
DELETE  
YES: Deletes the saved My Playlist. ;  
NO *: Cancels.  
■
[MPLIST DELETE] is selectable only when the source is  
About Audio file  
Playable Audio file  
“iPod”.  
■
: MP3 (.mp3), WMA (.wma)  
: AAC-LC (.m4a) KDC-BT648U/ KDC-X695  
only  
Playable disc media: CD-R/RW/ROM  
Playable disc file format: ISO 9660 Level  
■
■
1/2, Joliet, Romeo, Long file name.  
Playable USB device file system: FAT16,  
■
FAT32  
Continued to next page  
English 13  
■
■
■
Although the audio files are complied with  
the standards listed above, the play maybe  
impossible depending on the types or  
conditions of media or device.  
Detailed information and notes about the  
playable audio files are stated in an online  
manual on the following site:  
Latest compatible list of iPod/iPhone.  
For details, see:  
www.kenwood.com/cs/ce/ipod  
Type of control available varies depending  
on the type of connected iPod. For  
details, see above URL.  
The word “iPod” appearing in this manual  
indicates the iPod or iPhone connected to  
this unit with a connection cable, KCA-  
iP102 (optional accessory).  
If you start playback after connecting the  
iPod, the music that has been played by  
the iPod is played first.  
■
www.kenwood.com/cs/ce/audiofile/  
About USB device  
■
■
This unit can play audio files stored on a  
USB mass storage class device.  
Install the USB device in the place where  
■
it will not prevent you from driving your  
vehicle properly.  
You cannot connect a USB device via a  
USB hub and Multi Card Reader.  
Make sure all important data has been  
In this case, “RESUMING” is displayed  
without displaying a folder name, etc.  
Changing the browse item will display a  
correct title, etc.  
You cannot operate iPod if “KENWOOD” or  
“ꢀ” displayed on iPod.  
■
■
■
backed up to avoid losing the data.  
Connecting a cable whose total length  
■
is longer than 5 m can result in abnormal  
playback.  
A USB connection cable, CA-U1EX  
(optional accessory) is required for  
connecting a USB device.  
About “KENWOOD Music Editor”  
This unit supports the PC application  
■
■
“KENWOOD Music Editor Light ver1.1” or  
later.  
When you use the audio file with  
■
database information added by the  
“KENWOOD Music Editor Light ver1.1”, you  
can search a file by title, album or artist  
name using Music Search (page 11).  
About compatible iPod/iPhone  
Made for  
– iPod touch (4th generation)  
– iPod touch (3rd generation)  
– iPod touch (2nd generation)  
– iPod touch (1st generation)  
– iPod classic  
■
In the Instruction manual, the term “Music  
Editor media” is used to mean the device  
that contains audio files with database  
information added with KENWOOD Music  
Editor.  
“KENWOOD Music Editor Light ver1.1” is  
available from the following web site:  
www.kenwood.com/cs/ce/  
For further information on “KENWOOD  
Music Editor Light ver1.1”, refer to the site  
above or the application help.  
– iPod with video  
■
– iPod nano (6th generation)  
– iPod nano (5th generation)  
– iPod nano (4th generation)  
– iPod nano (3rd generation)  
– iPod nano (2nd generation)  
– iPod nano (1st generation)  
– iPhone 4  
■
– iPhone 3GS  
– iPhone 3G  
– iPhone  
(As of January 2011)  
14 English  
Operation of Hands-Free Phoning  
Preparation : KDC-X395/ KDC-348U: Only with the optional accessory KCA-BT300 or KCA-BT200  
connected.  
■
Press and hold for about 2 seconds to memorize the  
current phone number.  
Press briefly to recall memorized phone number.  
KDC-X395/ KDC-348U  
Press and hold to enter  
■
■
Bluetooth mode.  
Press to answer an incoming  
■
KDC-BT648U/ KDC-X695  
Press to enter Bluetooth mode.  
Press to answer an incoming call.  
call.  
■
■
When “CONFIRM PHONE” is displayed,  
confirm connection with a cell-phone  
operation.  
Getting Started  
Before use the cell-phone, you need to  
connect cell-phone to this unit.  
6 The receiver is connected to a cell-phone,  
with “HF CONNECT” displayed, and exits  
the easy pairing mode.  
■
For details on the Bluetooth cell-phone with  
the hands-free function, see <About the  
Cell-Phone> (page 22).  
■
For more details, see <Easy Pairing  
KDC-BT648U / KDC-X695  
1 Press and hold to enter easy pairing  
mode  
function> (page 18).  
If an error code is displayed during paring,  
see <Troubleshooting> (page 34).  
■
“PAIRING” is displayed.  
KDC-X395 / KDC-348U  
2 “SEARCHING” is displayed.  
Search for the Bluetooth device.  
When search is completed, “FINISHED” is  
displayed.  
The following 3 steps procedure is necessary.  
Step 1. Pairing (Registering from Bluetooth  
devices)  
1 Press SRC to turn on the power.  
2 Start registering this unit by operating  
the Bluetooth device.  
3 Turn the volume knob to select a cell-  
phone name, press to confirm.  
4 Input the PIN code  
By operating the Bluetooth device, register  
the hands-free unit (pairing). Select “KCA-  
BT300” or “KCA-BT200” from the list of  
connected units.  
■
Turn the volume knob to select the  
number.  
■
To move to the next digit, press ¢.  
■
To delete the last digit, press 4.  
3 Input the PIN code (“0000”) in the  
Bluetooth device.  
5 Press the volume knob to transmit the  
PIN code.  
Check that registration is complete on  
If “PAIRING OK” is displayed, registration is  
completed.  
Continued to next page  
English 15  
the Bluetooth device. PIN code is set to  
“0000” as the default. You can change this  
code. Refer to [PIN CODE EDIT] under  
<Bluetooth Setup> (page 22).  
BOOK”, then press to enter.  
3 Press to enter alphabet search mode.  
4 Turn the volume knob to select the  
character to be searched for.  
■
4 By operating the Bluetooth device, start  
hands-free connection.  
To move to the next row, press BAND.  
To return to the Phone Book mode, press  
■
Step 2. Connection  
.
If you have registered 2 or more cell-  
phones, you need to select one of them.  
For more details, see <Selecting the  
Bluetooth Device> (page 20).  
When a cell-phone is connected, the “BT”  
indicator lights up.  
5 Press the volume knob to start searching.  
6 Turn the volume knob to select a name  
and category.  
■
To move to the next character, press 4  
/ ¢.  
7 Press the volume knob to make a call.  
■
Step 3. Hands-free phoning  
To use the Phone Book, it must be  
You can do hand-free phoning when the  
connection is made.  
When registering from this unit. Refer to  
downloaded to this unit in advance. Refer to  
<Downloading the Phone Book> (page 17).  
During search, a non-accent character such  
■
■
<Registering Bluetooth Device (Pairing)>  
(page 19).  
as “u” is searched for instead of an accent  
character such as “ü”.  
The category items in the Phone Book are  
displayed as follows.  
GE: General ; HM: Home ; OF: Office ;  
MO: Mobile ; OT: Other  
■
Making a Call  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
2 Turn the volume knob to select a dialing  
Calling a Number in the Call Log  
2 Turn the volume knob to select the  
“OUTGOING” (outgoing call), “INCOMING”  
(incoming call), or “MISSED CALLS”  
(missed call), then press to enter.  
3 Turn the volume knob to select a name or  
phone number.  
method, then press to enter.  
■
Operation method of each mode is  
described below.  
–
“PHONE BOOK”: Calling a Number in the  
Phone Book  
“OUTGOING”/ “INCOMING”/ “MISSED  
4 Press the volume knob to make a call.  
–
■
The outgoing call list and the incoming call  
CALLS”: Calling a Number in the Call  
Log  
“NUMBER DIAL”: Dial a Number  
list, and the missed call list are the lists of  
calls originated from and received at this  
unit. They are not the ones stored in the  
cell-phone memory.  
–
–
“VOICE RECOG”: Make a Voice Dialing  
Call  
–
Speed Dialing (Preset Dial)  
Dial a Number  
■
Switches between name and phone  
number, press DISP.  
To return to the Bluetooth mode, press and  
2 Turn the volume knob to select “NUMBER  
DIAL”, then press to enter.  
3 Turn the volume knob to select the  
phone number  
■
hold  
.
■
To exit Bluetooth mode, press SRC.  
■
To move to the next digit, press ¢.  
■
To delete the last digit, press 4.  
Calling a Number in the Phone Book  
2 Turn the volume knob to select “PHONE  
■
Press number button (1 – 0), #(FM+),  
16 English  
■
*(AM–), or +(¢) on the remote  
controller.  
Audio sound is not output during voice  
recognition.  
4 Make a call.  
Receiving a Call  
Answering a Phone Call  
KDC-BT648U / KDC-X695  
■
Press the volume knob.  
Press OK on the remote controller.  
■
■
You can input max 25 (KDC-BT648U/  
Press  
.
KDC-X695) / 32 (KDC-X395/ KDC-348U) digits.  
KDC-X395 / KDC-348U  
Press the volume knob.  
Rejecting an Incoming Call  
Press SRC.  
Speed Dialing (Preset Dial)  
2 Press number button (1 – 6).  
3 Press the volume knob to make a call.  
During a Call  
Disconnecting a Call  
KDC-BT648U / KDC-X695  
Registering to the Preset Dial Number  
(Preset Memory)  
2 Enter the phone number with reference  
to the following:  
Dial a number/ Calling a number in the call  
log/ Calling a number in the Phone Book  
3 Press and hold number button (1 – 6) for  
about 2 seconds.  
Press  
.
KDC-X395 / KDC-348U  
Press SRC.  
Switching to the Private Mode  
Press number button 6 to switches  
between Private talk (“PRIVATE TALK”)  
and Hands-free talk (“HANDS FREE”).  
Make a Voice Dialing Call  
2 Turn the volume knob to select “VOICE  
RECOG”, then press to enter.  
“V-RECG READY” is displayed.  
3 Press the volume knob to start voice  
recognize.  
4 “PB NAME” is displayed.  
When a beep is heard, say the name within  
2 seconds.  
Call Waiting  
Answering Another Incoming Call with the  
Current Call Suspended  
Turn the volume knob to select  
[ANSWER], then press to enter.  
Continuing the Current Call  
Turn the volume knob to select [REJECT],  
then press to enter.  
5 “PN TYPE” is displayed.  
Switching between the Current Call and  
Waiting Call  
When a beep is heard, say the category  
name within 2 seconds.  
The recognized phone number (name) is  
displayed.  
Press the volume knob to switches the  
calling party.  
6 Press the volume knob to make a call.  
Downloading the Phone Book  
To download automatically  
■
This step is the same as step 4 of the  
procedure in <Calling a Number in the  
Phone Book> (page 16). You can make a  
call or select a category.  
If the cell-phone supports a phone book  
synchronization function, the phone  
book is downloaded automatically after  
Bluetooth connection.  
Setting on the cell-phone may be required.  
If no phone book data is found in the  
■
If your voice cannot be recognized, a  
message is displayed. Pressing the Volume  
knob allows you to retry voice input. Refer  
to <Troubleshooting> (page 34).  
■
■
unit even after the compete display, your  
cell-phone may not support automatic  
■
Both the name and category require  
registration of a voice tag. Refer to <Setting  
a Voice Command> (page 20).  
Continued to next page  
English 17  
■
download of phone book data. In this case,  
try downloading manually.  
To cancel downloading of the phone book  
data, operate the cell-phone.  
To download from the cell-phone manually  
1 By operating the cell-phone, end the  
hands-free connection.  
Using the remote controller (RC-405)  
Making a call:  
: Enter Bluetooth mode.  
2 By operating the cell-phone, send the  
phone book data to this unit  
5 / ∞ : Selects a dialing method.  
ENT 38 : Enter dialing mode  
DIRECT : Make a call  
By operating the cell-phone, download the  
phone book data to this unit.  
During downloading: “DOWNLOADING”  
0 — 9 : Input a digit in number dial mode.  
#FM+ : Input “#” in number dial mode.  
*AM– : Input “*” in number dial mode.  
■
is displayed.  
After completion of downloading:  
■
+¢  
: Input “+” in number dial mode.  
: Clear the entered phone number.  
“COMPLETE” is displayed.  
3 By operating the cell-phone, start the  
hands-free connection.  
To clear the downloading completion  
message, press any button.  
4
Receiving a call:  
: Answer the call.  
■
ENT 38 : Switch between the private talk  
mode and the hands-free talk  
mode.  
■
Up to 1000 phone numbers can be  
registered for each registered cell-phone.  
Up to 25 (KDC-BT648U/ KDC-X695)/ 32  
Call waiting:  
■
: Answer Another Incoming Call  
with the Current Call Suspended.  
: Answer another Incoming Call after  
Terminating the Current Call.  
: Continue the Current Call.  
(KDC-X395/ KDC-348U) digits can be  
registered for each phone number along  
with up to 50* characters representing a  
name.  
SRC  
1
(* 50: Number of alphabetical characters.  
Fewer characters can be input depending  
on the type of characters.)  
During a call:  
SRC : End the call.  
Bluetooth Setup  
Preparation : KDC-X395/ KDC-348U: Only with the optional accessory KCA-BT300 or KCA-BT200  
connected.  
–
“DEVICE FULL”: When maximum of  
five cell-phones have already been  
registered.  
Easy Pairing function  
• KDC-BT648U/ KDC-X695 only.  
1 Press and hold to enter easy pairing  
mode  
When registering a cell-phone for the first  
time, registering a cell-phone  
2 “SEARCHING” is displayed.  
Search for the Bluetooth device.  
When search is completed, “FINISHED” is  
displayed.  
“PAIRING” is displayed.  
Any of the following is displayed  
depending on cell-phone registration  
condition:  
■
–
“SEARCHING”: When registering a cell-  
phone for the first time.  
“(cell-phone name)”: When a cell-phone  
3 Turn the volume knob to select a cell-  
phone name, press to confirm.  
–
has already been registered.  
18 English  
4 Input the PIN code  
4 Press and hold the volume knob to delete  
the selected cell-phone.  
■
Turn the volume knob to select the  
number.  
“DELETE” is displayed.  
5 Turn the volume knob to select “YES”,  
then press to confirm.  
■
To move to the next digit, press ¢.  
■
To delete the last digit, press 4.  
5 Press the volume knob to transmit the  
PIN code.  
“COMPLETED” is displayed.  
Registering Bluetooth Device  
(Pairing)  
If “PAIRING OK” is displayed, registration is  
completed.  
Registering from Bluetooth devices  
1 Press SRC to turn on the power.  
2 Start registering this unit by operating  
the Bluetooth device.  
When “CONFIRM PHONE” is displayed,  
confirm connection with a cell-phone  
operation.  
6 The receiver is connected to a cell-phone,  
with “HF CONNECT” displayed, and exits  
the easy pairing mode.  
If an error code is displayed during paring,  
see <Troubleshooting> (page 34).  
By operating the Bluetooth device, register  
the hands-free unit (pairing). Select  
“KENWOOD BT CD/R-3P1”, “KCA-BT300” or  
“KCA-BT200” from the list of connected  
units.  
■
3 Input the PIN code (“0000”) in the  
Bluetooth device.  
When a cell-phone has already been  
registered, or maximum of five cell-phones  
have already been registered/ selecting a  
cell-phone  
2 “(cell-phone name)” or “DEVICE FULL” is  
displayed.  
Check that registration is complete on  
the Bluetooth device. PIN code is set to  
“0000” as the default. You can change this  
code. Refer to [PIN CODE EDIT] under  
<Bluetooth Setup> (page 22).  
3 Turn the volume knob to select a cell-  
phone name.  
4 By operating the Bluetooth device, start  
hands-free connection.  
■
To register a new cell-phone, select “[DVC  
SEARCH]”, then go to “When registering a  
cell-phone for the first time.”  
4 Press the volume knob to set up the  
cell-phone.  
Registering from this unit  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
■
“ꢁ(cell-phone name)”: The selected  
Press and hold the volume knob to enter  
Bluetooth mode.  
Bluetooth device is busy.  
“-(cell-phone name)”: The selected  
■
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select  
[PAIRING], then press to enter.  
4 Turn the volume knob to select [DEVICE  
SEARCH], then press to enter.  
5 Press the volume knob to search for the  
Bluetooth device.  
Bluetooth device is on standby.  
“ (cell-phone name)“: The Bluetooth  
device is deselected.  
If a cell-phone is already selected,  
deselect it, and then select a different  
one.  
■
■
5 Press to exit easy pairing mode.  
When search is completed, “FINISHED” is  
displayed.  
6 Turn the volume knob to select a  
Bluetooth device name, press to confirm.  
Continued to next page  
Deleting the registered cell-phone  
2 “(cell-phone name)” or “DEVICE FULL” is  
displayed.  
3 Turn the volume knob to select a cell-  
phone name.  
English 19  
7 “PAIRING” is displayed (KDC-X395/  
KDC-348U with KCA-BT300 only)  
If “PAIRING OK” is displayed, proceed to  
step 10.  
If “PIN CODE NG” is displayed, proceed to  
steps 8.  
8 Input the PIN code  
Bluetooth mode.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select  
[PAIRING], then press to enter.  
4 Turn the volume knob to select [PHONE  
SELECT] or [AUDIO SELECT], then press  
to enter.  
■
Turn the volume knob to select the number.  
To move to the next digit, press ¢.  
To delete the last digit, press 4.  
■
5 Turn the volume knob to select a  
Bluetooth device name.  
■
9 Press the volume knob to transmit the  
PIN code.  
6 Press the volume knob to set up the  
Bluetooth device.  
■
If “PAIRING OK” is displayed, registration is  
completed. If the error message appears  
even though the PIN code is correct, try  
Registering Special Bluetooth device.  
“ꢁ(Device name)”: The selected Bluetooth  
device is busy.  
“-(Device name)”: The selected Bluetooth  
■
device is on standby.  
“ (Device name)“: The Bluetooth device is  
■
10 Hold  
to finish the procedure.  
■
To exit Bluetooth mode, press SRC.  
If there are 5 or more Bluetooth devices  
registered, you cannot register a new  
Bluetooth device.  
deselected.  
If a cell-phone is already selected,  
■
■
deselect it, and then select a different  
one.  
7 Hold  
to finish the procedure.  
■
Registering Special Bluetooth device  
To exit Bluetooth mode, press SRC.  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
Setting a Voice Command  
Registering Phone Book Name  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select  
[PAIRING], then press to enter.  
4 Turn the volume knob to select [S-DVC  
SELECT], then press to enter.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select [VOICE  
TAG], then press to enter.  
4 Turn the volume knob to select [PB  
NAME EDIT], then press to enter.  
5 Search for the Phone Book name to  
register  
5 Turn the volume knob to select a device  
name, press to confirm.  
6 Go through the procedure step 4  
of <Registering from this unit> and  
complete the registration (pairing).  
Select the name to register with reference  
to 5 in <Calling a Number in the Phone  
Book> (page 16).  
■
If the device name is not in the list, select  
“OTHER PHONE”.  
Selecting the Bluetooth Device  
If a voice tag has already been registered  
for a name, “*” is displayed before the  
name.  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
6 Turn the volume knob to select [PB  
NAME REG], then press to enter.  
20 English  
■
■
■
■
To select “PB NAME CHK”, play the  
registered voice.  
To select “PB NAME DEL”, delete a voice  
tag. Turn the volume knob to select “YES”,  
then press to confirm.  
To select “PN TYPE CHK”, play the  
registered voice. (KDC-X395/ KDC-348U  
only)  
To select “PN TYPE DEL”, delete a voice  
tag. Turn the volume knob to select  
“YES”, then press to confirm. (KDC-X395/  
KDC-348U only)  
7 “ENTER 1” is displayed. When a beep is  
heard, say a voice tag within 2 seconds.  
8 “ENTER 2” is displayed. When a beep is  
heard, say the same voice tag as that you  
said in step 7 within 2 seconds.  
“COMPLETE” is displayed.  
9 Press the volume knob to return to step 5.  
To exit Setting mode, press  
7 “ENTER 1” is displayed. When a beep is  
heard, say a voice tag within 2 seconds.  
8 “ENTER 2” is displayed. When a beep is  
heard, say the same voice tag as that you  
said in step 7 within 2 seconds.  
“COMPLETE” is displayed.  
■
.
■
■
■
To exit Bluetooth mode, press SRC.  
You can register up to 35 voice tags.  
Audio sound is not output during voice tag  
registration.  
9 Press the volume knob to return to step  
5.  
Set the voice tag for all the 5 categories. If  
the voice tag is not registered for all the  
categories, the Phone book may not be  
recalled by voice command.  
■
Registering Phone Book Name Type  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
Bluetooth Setup  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select [VOICE  
TAG], then press to enter.  
4 Turn the volume knob to select [PN TYPE  
EDIT], then press to enter.  
5 Turn the volume knob to select  
[GENERAL], [HOME], [OFFICE], [MOBILE],  
or [OTHER], then press to enter.  
6 Turn the volume knob to select [PN TYPE  
REG], then press to enter.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to make a  
selection, then press to confirm.  
■
See table below for selection.  
Repeat step 3 until the desired item is  
■
selected/activated.  
■
Press  
4 Hold  
to return to the previous item.  
to finish the procedure.  
■
To exit Bluetooth mode, press SRC.  
Item  
PAIRING  
Selectable setting (Preset: *)  
DEVICE SEARCH Registers a Bluetooth device (pairing).  
(For details, see page 19.)  
PHONE SELECT Selects a cell-phone connection.  
(For details, see page 20.)  
AUDIO SELECT KDC-X395/ KDC-348U only:  
Selects a Bluetooth audio player connection. (For details, see page 20.)  
S-DVC SELECT (For details, see page 19.)  
Continued to next page  
English 21  
Item  
DEVICE DELETE Cancel registration of the Bluetooth device.  
1. Turn the volume knob to select the Bluetooth device, then press to confirm.  
Selectable setting (Preset: *)  
2. Turn the volume knob to select “YES”, then press to confirm.  
SMS DOWNLOAD Download a short message. (For details, see page 23.)  
VOICE TAG  
PB NAME EDIT Registers voice for voice recognition and voice to select the Phone number category in Phone book.  
(For details, see page 20.)  
PN TYPE EDIT  
DETAILED SET  
PIN CODE EDIT Specify the PIN code required when registering this unit using the Bluetooth device. By default, “0000” is  
specified.  
1. Turn the volume knob to select the number.  
■
To move to the next digit, press  
¢
.
■
To delete the last digit, press  
4
.
2. Press the volume knob to register a PIN code  
AUTO ANSWER OFF: Does not answer the phone call automatically. ; 0: Automatically answers the phone call at once. ;  
1 – 8 * –99: Automatically answers the phone call after lapse of 1 – 99 seconds.  
RECONNECT  
KDC-BT648U/ KDC-X695 only  
ON *: Automatically reconnects the selected Bluetooth device when radio wave becomes strong enough,  
even after it is disconnected. ; OFF: Cancels.  
■
When this function is turned ON, the Bluetooth device is reconnected if it has been disconnected by  
selecting [PHONE SELECT].  
BT HF /  
BT HF/AUDIO  
FRONT *: Outputs audio from the front-left and front-right speakers. ; ALL: Outputs audio from the all  
speakers.  
CALL BEEP  
ON *: You can output a beep from the speaker when a call comes in. ; OFF: Cancels.  
BT F/W UPDATE Display the firmware version and update the firmware.  
MIC GAIN  
–3 — 0 * — +3: Adjust the sensitivity of the built-in microphone for a telephone call. Adjust the voice of  
caller. Setting to “+” increases the voice volume.  
NR LEVEL  
–3 — 0 * — +3: Reduce the noises generated by surrounding environment without changing the  
built-in microphone volume. Adjust the voice of caller when it is not clear. Setting to “+” increases the noise  
reduction.  
EC LEVEL  
MIC SELECT  
–2 — 0 * — +2: Adjust the level of echo cancellation. Setting to “+” increases the echo cancel reduction.  
Determines whether the built-in or external microphone is to be used when the receiver incorporates a  
microphone. IN *: Use the built-in microphone. ; EXT: Use the external microphone.  
■
[MIC GAIN], [NR LEVEL], [EC LEVEL] is selectable only for KDC-BT648U, KDC-X695 and KDC-X395/KDC-348U with KCA-BT300.  
About the Cell-Phone  
www.kenwood.com/cs/ce/bt/  
The units supporting the Bluetooth  
■
■
Version: Bluetooth Standard Ver. 2.0  
Profile:  
■
function have been certified for  
conformity with the Bluetooth Standard  
following the procedure prescribed  
by Bluetooth SIG. However, it may be  
impossible for such units to communicate  
with your cell-phone depending on its  
type.  
HFP (Hands Free Profile)  
OPP (Object Push Profile)  
PBAP (Phone book Access Profile)  
SYNC (Synchronization Profile)  
For the cell-phones verified for compatibility,  
access the following URL:  
22 English  
SMS (Short Message Service)  
Preparation : KDC-X395/ KDC-348U: Only with the optional accessory KCA-BT300 or KCA-BT200  
connected.  
KDC-X395/ KDC-348U  
Press and hold to enter  
Bluetooth mode.  
KDC-BT648U/ KDC-X695  
Press to enter Bluetooth mode.  
Display the SMS  
Downloading the SMS  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
¤
To prevent car accidents, the driver should  
not read the SMS while driving.  
When a new message arrives  
“SMS RECEIVED” is displayed.  
Press and hold the volume knob to enter  
Bluetooth mode.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to select [SMS  
DOWNLOAD], then press to enter.  
4 Start downloading  
Displaying the SMS  
1
KDC-BT648U / KDC-X695  
Press to enter Bluetooth mode.  
KDC-X395 / KDC-348U  
Press and hold the volume knob to enter  
Bluetooth mode.  
■
During downloading: “DOWNLOADING”  
is displayed.  
After completion of downloading:  
■
2 Turn the volume knob to select [SMS  
INBOX], then press to enter.  
3 Turn the volume knob to select a  
message.  
“COMPLETE” is displayed.  
5 Hold  
to finish the procedure.  
■
To exit Bluetooth mode, press SRC.  
The cell-phone must be able to transmit the  
SMS using Bluetooth. Setting on the cell-  
phone may be required. If the cell-phone  
does not support SMS function, the SMS  
download item in Function Control mode is  
not displayed.  
When the SMS is downloaded from the  
cell-phone, the unopened messages in the  
cell-phone are opened.  
■
■
Switches between name, phone number  
and message reception date, press DISP.  
4 Press the volume knob to display the  
text.  
■
To scrolls the message, turn the volume  
knob.  
■
■
■
To return to the message list, press the  
volume knob.  
5 Hold  
to finish the procedure.  
The already-read and unread short  
messages can be respectively downloaded  
up to 75.  
■
To exit Bluetooth mode, press SRC.  
Continued to next page  
English 23  
■
■
The unopened message is displayed at the  
beginning of the list. Other messages are  
displayed in the order of reception.  
The SMS that has arrived when the cell-  
phone is not linked with Bluetooth cannot  
be displayed. Download the SMS.  
The short message cannot be displayed  
during downloading the SMS.  
■
■
Unread messages are prefixed with an  
asterisk (*).  
HD Radio™ Tuner Control  
Preparation : Only with the optional accessory HD Radio tuner connected. When you connect  
an HD Radio tuner, Tuner features of the unit are disabled and changed to HD Radio tuner  
features. With the HD Radio tuner, you can use the similar functions of Tuner features.  
■
Press and hold for about 2 seconds to memorize the current station.  
Press briefly to recall memorized station.  
■
Direct Access Tuning using the  
remote controller (RC-405)  
• Only with optional accessory KTC-HR300 tuner  
connected.  
1 Press BAND to select a band.  
2 Press DIRECT to enter Direct Access  
Tuning mode.  
1 Press SRC to select “HD RADIO”.  
2 Press BAND repeatedly to select a band  
(FM1/ FM2/ FM3/ AM).  
3 Press 4 / ¢ to search for a station or  
channel.  
The following indicator lights up when...  
HD: Lights when HD Radio broadcasting is  
tuned.  
D: Lights when HD Radio digital broadcasting  
is tuned.  
MC: Lights when HD Radio multicast  
broadcasting is tuned.  
TAG: Lights when iTunes Tagging is enabled.  
“– – – –” appears.  
3 Press DIRECT to select tuning item.  
–
“– – – –” : Frequency.  
“HD –” : Channel.  
Cancelling Direct Access Tuning.  
–
–
4 Press the number buttons to enter the  
frequency or channel.  
5 Press 4 / +¢ to search for the  
frequency or channel.  
24 English  
■
■
To cancel the Direct Access Tuning mode,  
press  
If you make no button operation for 10  
seconds, the Direct Access Tuning mode is  
automatically canceled.  
The saved songs will then show up in a  
playlist called “Tagged” in iTunes the every  
next time you sync your iPod to your  
computer. So then you just need to click and  
then easily buy and download the song you  
were tagging directly from the Apple iTunes  
Music Store.  
.
Using the remote controller (RC-405)  
#FM+ / *AM– : Selects band.  
Adjust [SETTINGS] mode settings  
While listening to the radio...  
1 Press the volume knob to enter  
[FUNCTION] mode.  
4 / +¢  
1 – 6  
: Selects station.  
: Selects preset station.  
iTunes Tagging  
• Only with optional accessory KTC-HR300 tuner  
connected.  
2 Turn the volume knob to select  
[SETTINGS], then press to enter.  
3 Turn the volume knob to make a  
selection, then press to confirm.  
See table below for selection.  
Pressing and holding while “TAG” is lit  
saves song’s information.  
4 Hold  
to finish the procedure.  
Item  
Selectable setting (Preset: *)  
SEEK MODE  
Selects the tuning mode for 4 / ¢ buttons.  
AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. ;  
MANUAL: Manually search for a station.  
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ; NO *: Cancels (automatic memorizing is  
not activated). (Selectable only if [NORM] is selected for [PRESET TYPE].) (page 5)  
RECEIVE MODE AUTO *: Automatically tunes to analog broadcast when there is no digital broadcast. ; DIGITAL: Digital broadcasts  
only. ; ANALOG: Analog broadcasts only.  
TAG MEMORY Only with optional accessory KTC-HR300 connected.  
##/50: Displays the tag memory usage of HD Radio receiver. Up to 50 tags can be registered to this unit.  
English 25  
Satellite Radio Tuner Control  
Preparation : Only with the optional accessory Satellite radio tuner connected.  
■
Press and hold for about 2 seconds to memorize the current channel.  
Press briefly to recall memorized channel.  
■
Channel Scan  
1 Press SRC to select “SIRIUS” or “XM”.  
2 Press BAND repeatedly to select a band  
(SR1/ SR2/ SR3/ SR4 ; XM1/ XM2/ XM3/  
XM4).  
1 Press and hold to start Channel Scan.  
Every receivable channel is checked for 10  
seconds.  
2 Press to receives the current channel.  
3 Press 4 / ¢ to search for a channel.  
■
You need to register to the service provider  
Direct Access Tuning using the  
remote controller (RC-405)  
1 Press DIRECT to enter Direct Access  
Tuning mode.  
“– – –” appears.  
2 Press the number buttons to enter the  
channel number.  
to receive the service by Satellite Radio.  
Consult the service provider if “CALL … TO  
SUBSCRIBE” appears.  
■
The radio may take a little time to start  
receiving after you select the Satellite Radio  
source.  
If the signal reception fails, “ACQUIRING  
■
3 Press 4 / +¢ to search for the  
SIGNAL”/ “NO SIGNAL” appears.  
channel.  
■
Category and Channel Search  
1 Press to enter Category and Channel  
Search mode.  
2 Turn the volume knob to select a  
category, then press to confirm.  
3 Turn the volume knob to select a  
To cancel the Direct Access Tuning mode,  
press  
.
■
■
If you make no button operation for 10  
seconds, the Direct Access Tuning mode is  
automatically canceled.  
If you cannot receive any signal in the input  
Channel due to bad conditions on radio  
wave or other such problems, “ACQUIRING  
SIGNAL”/ “NO SIGNAL” appears.  
channel, then press to confirm.  
To return to the category select, press  
■
.
■
To cancel the Category and Channel Search  
mode, press and hold  
.
Using the remote controller (RC-405)  
#FM+  
: Selects band.  
4 / +¢  
1 – 6  
: Selects channel.  
: Selects preset channel.  
26 English  
Adjust [SETTINGS] mode settings  
While listening to the radio...  
1 Press the volume knob to enter [FUNCTION] mode.  
2 Turn the volume knob to select [SETTINGS], then press to enter.  
3 Turn the volume knob to make a selection, then press to confirm.  
See table below for selection.  
4 Hold  
Item  
to finish the procedure.  
Selectable setting (Preset: *)  
SEEK MODE  
Selects the tuning mode for 4 / ¢ buttons.  
CHANNEL *: Normal manual seeking control. ; PRESET: Search in order of the channels in the Preset memory  
ESN=: Displays the Electronic Serial Number of satellite radio.  
ESN WATCH  
English 27  
Function settings  
1 Press SRC to select a source other than “STANDBY”.  
2 Press the volume knob to enter [FUNCTION] mode.  
3 Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter.  
4 Turn the volume knob to make a selection, then press to confirm.  
■
See table below for selection.  
Repeat step 3 until the desired item is selected/activated.  
■
■
Press  
to return to the previous item.  
5 Hold  
to finish the procedure.  
[AUDIO CONTROL] : While listening to any source except in STANDBY state or Bluetooth mode.  
Item  
SUB-W LEVEL  
BASS BOOST  
SYSTEM Q  
Selectable setting (Preset: *)  
–15 — 0 * — +15: Adjusts the subwoofer output level.  
B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.  
NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the  
music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)  
KDC-X695/ KDC-X395 only:  
BASS ADJUST  
BASS CTR FRQ 40/ 50/ 60/ 70/ 80/ 100 */ 120/ 150: Selects the center frequency.  
BASS LEVEL –8 — 0 * — +8: Adjusts the level.  
BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.  
BASS EXTEND ON: Turns on the extended bass. ; OFF *: Cancels.  
MID ADJUST  
KDC-X695/ KDC-X395 only:  
MID CTR FRQ  
MID LEVEL  
0.5K/ 1.0K/ 1.5K/ 2.0K *: Selects the center frequency.  
–8 — 0 * — +8: Adjusts the level.  
MID Q FACTOR 1.00 */ 2.00: Adjusts the quality factor.  
TRE ADJUST  
KDC-X695/ KDC-X395 only:  
TRE CTR FRQ  
TRE LEVEL  
10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.  
–8 — 0 * — +8: Adjusts the level.  
BASS LEVEL  
KDC-BT648U/ KDC-348U only:  
–8 — 0 * — +8: Source tone memory: Adjusts the level to memorize in each source. (Before making an  
adjustment, select the source you want to adjust.)  
MID LEVEL  
TRE LEVEL  
BALANCE  
FADER  
L15 — 0 * — R15: Adjusts the left and right speaker output balance.  
R15 — 0 * — F15: Adjusts the rear and front speaker output balance.  
SUBWOOFER SET ON *: Turns on the subwoofer output. ; OFF: Cancels.  
DETAILED SET  
HPF FRONT  
THROUGH *: All signals are sent to the front speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies  
lower than the specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)  
THROUGH *: All signals are sent to the rear speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies  
lower than the specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)  
THROUGH *: All signals are sent to the subwoofer. ; 50/60/80/100/120 (HZ): Frequencies higher than the  
specified value are cut off. (Underlined: KDC-X695/ KDC-X395 only)  
HPF REAR  
LPF  
SUBWOOFER  
28 English  
Item  
Selectable setting (Preset: *)  
SUB-W PHASE REVERSE (180°)/ NORMAL (0°) *: Selects the phase angle of the subwoofer output to be in line with the  
speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for  
[LPF SUBWOOFER].)  
SUPREME SET ON *: Creates realistic sound by interpolating the high-frequency components that are lost in AAC/ MP3/  
WMA audio compression. ; OFF: Cancels. (Selectable only when playback an AAC/ MP3/ WMA disc or a USB  
device, except iPod.)  
VOLUME OFFSET –8 — 0 * — +8 (for AUX) ; –8 — 0 * (for other sources): Presets the volume adjustment level of each  
source. The volume level will automatically increase or decrease when you change the source. (Before making  
an adjustment, select the source you want to adjust.)  
■
■
Select a source before making a source tone memory adjustment, [BASS ADJUST/ MID ADJUST/ TRE ADJUST].  
[SUB-W LEVEL/ LPF SUBWOOFER/ SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].  
[SETTINGS]  
Item  
AUX NAME SET  
Selectable setting (Preset: *)  
AUX */ TV/ VIDEO/ GAME/ PORTABLE/ DVD: Selects the desired name for the connected component.  
(Selectable only if “AUX” is selected as the source.)  
CLOCK  
CLOCK ADJUST (For details, see page 5.)  
TIME SYNC  
DISPLAY  
ON: Synchronizes the Radio Data System station time data and the unit’s clock. ; OFF *: Cancels.  
DIMMER SET ON: Dims the display illumination. ; OFF *: Cancels.  
TEXT SCROLL AUTO */ ONCE: Selects to scroll the display information automatically, or scroll only once. ; OFF: Cancels.  
BT DVC STATUS You can display the connection status, signal strength, and battery level of cell-phone.  
HF-CON: Connection status for cell-phone. ; AD-CON: Connection status for BT Audio. ; BATT: Battery level of  
cell-phone. ; SIGNAL: Signal strength of cell-phone.  
TUNER SET  
TI: Selectable only if any source other than tuner source is selected. (For details, see page 8.)  
English 29  
Installation/connection  
■
Part list:  
If the power is not turned ON (“PROTECT”  
A Faceplate ...................................................................(×1)  
B Escutcheon..............................................................(×1)  
C Mounting sleeve...................................................(×1)  
D Wiring harness.......................................................(×1)  
E Removal tool.......................................................... (×2)  
F Flat head screw (for Nissan cars).................(×4)  
G Round head screw (for Toyota cars).........(×4)  
H Microphone (3 m) (KDC-X695 only)..........(×1)  
is displayed), the speaker wire may have a  
short-circuit or touched the chassis of the  
vehicle and the protection function may  
have been activated. Therefore, the speaker  
wire should be checked.  
Caution  
■
If your car’s ignition does not have an ACC  
position, connect the ignition wires to a  
power source that can be turned on and  
off with the ignition key. If you connect  
the ignition wire to a power source with  
a constant voltage supply, as with battery  
wires, the battery may die.  
Do not use your own screws. Use only the  
screws provided.  
Install this unit in the console of your  
vehicle. Make sure the faceplate will not hit  
the lid of the console (if any) when closing  
and opening.  
After the unit is installed, check whether the  
brake lamps, blinkers, wipers, etc. on the car  
are working properly.  
Mount the unit so that the mounting angle  
is 30° or less.  
If the fuse blows, first make sure the wires  
are not touching to cause a short circuit,  
then replace the old fuse with one that has  
the same rating.  
Connect the speaker wires correctly to the  
terminals to which they correspond. The  
unit may be damaged or fail to work if you  
share the · wires or ground them to any  
metal part in the car.  
Basic procedure  
1 Remove the key from the ignition switch,  
then disconnect the · terminal of the  
car battery.  
2 Make proper input and output wire  
connections.  
\ <Wiring connection> (page 32)  
3 Install the unit to your car.  
\ <Installing the unit> (page 33)  
4 Reconnect the · terminal of the car  
battery.  
■
■
■
5 Reset the unit. (page 4)  
Warning  
■
■
■
The unit can only be installed in a car with a  
12 V DC power supply, negative ground.  
If you connect the ignition wire (red) and  
■
the battery wire (yellow) to the car chassis  
(ground), you may cause a short circuit,  
that in turn may start a fire. Always connect  
those wires to the power source running  
through the fuse box.  
■
■
Disconnect the battery’s negative terminal  
and make all electrical connections before  
installing the unit.  
Insulate unconnected wires with vinyl tape  
■
When only two speakers are being  
connected to the system, connect the  
connectors either to both the front output  
terminals or to both the rear output  
terminals (do not mix front and rear).  
■
or other similar material. To prevent a short  
circuit, do not remove the caps on the ends  
of the unconnected wires or the terminals.  
■
Be sure to ground this unit to the car’s  
chassis again after installation.  
30 English  
■
Mounting and wiring this product requires  
skills and experience. For safety’s sake, leave  
this work to professionals.  
If you experience problems during  
installation, consult your Kenwood dealer.  
Reception may drop if there are metal  
objects near the Bluetooth antenna.  
About Bluetooth unit (Optional:  
KDC-X395/ KDC-348U)  
■
This unit supports KCA-BT300 or KCA-BT200.  
Plugging a KCA-BT300/ KCA-BT200 into this  
unit will enable BT audio.  
■
■
– Selecting Bluetooth Audio source  
Press SRC to select the “BT AUDIO EXT”.  
– To pause/resumes playback, press number  
button 6 (38).  
– To selects track, press 4 or ¢.  
Set the Type Switch on KCA-BT300/ KCA-  
BT200 as follows:  
Bluetooth antenna unit  
■
1: OFF, 2: OFF, 3: OFF  
For Good Reception  
To assure good reception, note the following:  
Communicate with the cell-phone within  
About Satellite Radio tuner  
(Optional)  
■
the line-of-sight distance of 10 m (30  
ft). The communication range becomes  
shorter depending on the surrounding  
environment. The communication  
range also becomes shorter when there  
is an obstacle between this unit and  
the cell-phone. The above maximum  
communication range (10 m) is not always  
assured.  
■
This unit supports Satellite Radio tuners  
which are released by SIRIUS and XM.  
Refer to the instruction manual of Satellite  
radio tuner.  
■
HD Radio™ Tuners that can be  
connected to this unit  
• KTC-HR300 • KTC-HR200 • KTC-HR100TR  
■
A broadcast station or walkie-talkie located  
nearby can interfere with communication  
due to too strong signal.  
¤ CAUTION  
Install this unit in the console of your  
vehicle.  
Do not touch the metal part of this unit  
during and shortly after the use of the  
unit. Metal part such as the heat sink and  
enclosure become hot.  
English 31  
Wiring connection  
USB connector  
AUX input (Stereo)  
FM/AM antenna  
input (JASO)  
Use the mini-plug (3.5 mm; 1/8”) cable  
which is stereo type and does not have  
any resistance.  
Antenna Cord  
Rear output  
Front output  
L
R
Sub Woofer output  
Fuse (10A)  
Microphone H  
(KDC-X695 only)  
Wiring harness D  
To Kenwood disc changer/  
External optional accessory  
(To connect these leads, refer  
to the relevant instruction  
manuals.)  
White  
White/Black  
Gray  
Gray/Black  
Green  
Green/Black  
To front left speaker  
To front right speaker  
To rear left speaker  
Purple  
To rear right speaker  
Purple/Black  
If no connections are made, do not let the wire come out from the tab.  
Blue/White  
Connect either to the power control terminal when  
using the optional power amplifier, or to the antenna  
control terminal in the vehicle.  
P.CONT  
(Power control/ Antenna  
control wire)  
Brown  
To connect the Kenwood navigation system, consult  
your navigation manual.  
MUTE  
(Mute control wire)  
(Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
KDC-X395/ KDC-348U only)  
Light Blue/Yellow  
To use the steering wheel remote control feature, you  
need to an exclusive remote adapter (not supplied)  
matches your car is required.  
REMOTE CONT  
(Steering remote control  
wire)  
STEERING WHEEL  
REMOTE INPUT  
Blue  
(Not used)  
ANT. CONT  
Car fuse box  
ACC  
Ignition key switch  
Red (Ignition wire)  
Yellow (Battery wire)  
Car fuse box  
(Main fuse)  
Black (Ground wire)  
To the metallic body or chassis of the car  
+
–
Battery  
32 English  
Installing the unit  
1
3
Connect the wiring harness to the  
unit. Other wiring connection has  
been completed earlier. (page 32)  
C
2
1
B
D
A
2
Before attaching, make  
sure the direction of the  
escutcheon is correct.  
(Wider hooks on the  
bottom side.)  
2
1
Dashboard of  
your car  
3
C
4
Bend the appropriate tabs  
to hold the mounting sleeve  
firmly in place.  
5
B
A
Installing without using the mounting sleeve (Japanese car)  
1 Remove the mounting sleeve and  
N
T
escutcheon B from the unit.  
T/N  
N
T
2 Align the holes in the unit (on both sides)  
with the vehicle mounting bracket and  
secure the unit with the supplied screws.  
B
T: Toyota cars  
N: Nissan cars  
8 mm  
MAX.  
8mm  
MAX.  
F
ø5mm G  
ø5mm  
Removing the unit  
1 Detach the faceplate A.  
E
2 Engage the catch pin on the removal  
tools E into the holes on both sides of  
the escutcheon B, then pull it out.  
3 Insert the removal tools E deeply into  
the slots on each side, then follow the  
arrows instructions as shown on the  
right.  
B
C
3
1
A
2
E
English 33  
Installation the Microphone Unit (KDC-X695 only)  
1 Check the installation position of the  
microphone H.  
2 Remove oil and other dirt from the  
installation surface.  
H
3 Install the microphone.  
4 Wire the microphone cable up to the  
hands-free box with it secured at several  
positions using tape or the like.  
■
Install the microphone as far away as  
possible from the cell-phone.  
Fix a cable with a commercial  
item of tape.  
Peel the release coated  
paper of double-face  
adhesive tape to fix on  
the place shown above.  
Adjust the direction  
of the microphone to  
the driver.  
Troubleshooting  
Symptom  
Remedy/Cause  
Adjust the volume to the optimum level. / Check the cords and connections.  
“PROTECT” appears and no operations can Check to be sure the terminals of the speaker leads are covered with insulating tape  
Sound cannot be heard.  
be done.  
properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest  
service center.  
Reset the unit.  
The unit does not work at all.  
Radio reception is poor. / Static noise while Connect the antenna firmly. / Pull the antenna out all the way.  
listening to the radio.  
“IN” flashes.  
The CD player is not operating properly. Reinsert the disc properly. If the condition did  
not improve, turn off the unit and consult your nearest service center.  
Insert a finalized CD-R/CD-RW (finalize with the component which you used for  
recording).  
CD-R/CD-RW cannot be played back and  
tracks cannot be skipped.  
Disc sound is sometimes interrupted.  
Stop playback while driving on rough roads. / Change the disc. / Check the cords and  
connections.  
“NA FILE” appears.  
“NO DISC” appears.  
“TOC ERROR” appears.  
The unit is playing an unsupported audio file.  
Insert a playable disc into the loading slot.  
The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try another  
disc instead.  
“ERROR 77” or “ERROR 99” appears.  
The unit is malfunctioning for some reason. Press the reset button on the unit. If the  
“ERROR 77”/ “ERROR 99” code does not disappear, consult your nearest service center.  
34 English  
Symptom  
“COPY PRO” appears.  
Remedy/Cause  
A copy-protected file is played.  
“READ ERROR” appears.  
Copy the files and folders for the USB device again. If the error message is still  
displayed, initialize the USB device or use other USB devices.  
No USB device is connected. Connect a USB device, and change the source to USB  
again.  
“NO DEVICE” appears.  
“NO MUSIC” or “ERROR 15” appears.  
The connected USB device contains no playable audio file. / Media was played that  
does not have data recorded that the unit can play.  
“NA DEVICE” appears.  
“USB ERROR” appears.  
Connect a supported USB device, and check the connections.  
Remove the USB device, turn the unit off, then turn it on again. If the unit still showing  
the same display, try to connect another USB device.  
“iPod ERROR” appears.  
Reconnect the iPod. / Confirm that the software for the iPod is the latest version. /  
Reset the iPod.  
Noise is generated.  
Skip to another track or change the disc.  
Tracks cannot play back as you have intended Playback order is determined when files are recorded.  
them to play.  
“READING” keeps flashing.  
Elapsed playing time is not correct.  
Longer readout time is required. Do not use too many hierarchies and folders.  
This is caused by how the tracks are recorded.  
The number of songs contained in “SONGS” Podcast files are not counted in this unit as this unit does not support the playback of  
category of this unit is different from that  
contained in “SONGS” category of iPod.  
Correct characters are not displayed (e.g.  
album name).  
podcast files.  
This unit can only display letters (upper case), numbers, and a limited number of  
symbols.  
Bluetooth  
Symptom  
Remedy/Cause  
The hands-free talk volume is low.  
The hands-free talk volume can be adjusted independently. Adjust it during hands-  
free talk. [MIC GAIN], [NR LEVEL] and [EC LEVEL] of <Bluetooth Setup> (page 21).  
No beep is heard at reception of an incoming No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of  
call.  
<Bluetooth Setup> (page 21) is set ON.  
■
Voice is not recognized.  
The vehicle window is open. If the surrounding noise is large, voice cannot be  
recognized properly. Close the vehicle windows to reduce noise.  
Small voice. If voice is too small, it cannot be recognized properly. Speak into the  
■
microphone a little more loudly and naturally.  
The person uttering the voice tag is not the one who registered the it. Only the  
■
voice of the person who registered the voice tag can be recognized.  
The calling party does not notify a caller ID. / There is no phone number data.  
There is no outgoing call list. / There is no incoming call list. / There is no missed call  
list. / There is no phone book list.  
“NO NUMBER” appears.  
“NO DATA” appears.  
“NO ENTRY” appears.  
The cell-phone has not been registered (pairing).  
“HF DISCONCT” appears.  
The unit cannot communicate with the cell-phone.  
Continued to next page  
English 35  
Symptom  
“HF ERROR 07” appears.  
Remedy/Cause  
The memory cannot be accessed. Turn off the power and on again. If this message still  
appears, press the reset button on the control unit.  
The unit cannot communicate with the cell-phone. Turn off the power and on again. If  
this message still appears, press the reset button on the control unit.  
The Bluetooth device cannot be detected.  
“HF ERROR 68” appears.  
“UNKNOWN” appears.  
“DEVICE FULL” appears.  
5 Bluetooth device have already been registered. No more Bluetooth device cannot  
be registered.  
“PIN CODE NG” appears.  
“CONNECT NG” appears.  
“PAIRING NG” appears.  
“NO MARCHING” appears.  
The PIN code is wrong.  
The unit cannot be connected to the device.  
Pairing error.  
The voice tag is wrong. Voice cannot be recognized because of an unregistered voice  
tag, etc.  
“TOO SOFT” appears.  
Voice is too small and cannot be recognized.  
Voice is too large to be recognized.  
The word or utterance is too long to be recognized.  
Data is not contained in the phone book.  
“TOO LOUD” appears.  
“TOO LONG” appears.  
“NO PHONEBOOK” appears.  
“NO MESSAGE” appears.  
“NO RECORD” appears.  
“MEMORY FULL” appears.  
No short message in In Box.  
The voice tag is not registered in the phone book.  
The number of voice tags reaches the maximum number to be registered in the phone  
book.  
“NO VOICE” appears.  
No call.  
■
The sound from the Bluetooth audio player is Another Bluetooth device is affecting the Bluetooth communication. Turn off  
discontinuous.  
another Bluetooth device. Move another Bluetooth device away from this unit.  
Another Bluetooth device or profile is used for communication. The downloading of  
the Phone book or the SMS disconnects the sound.  
■
HD Radio/ SIRIUS/ XM  
Symptom  
Remedy/Cause  
“MEMORY FULL” appears.  
“iPod FULL” appears.  
The tag memory of HD Radio receiver is FULL.  
The iPod memory is FULL.  
“NO TAG FNC” appears.  
“TAG ERROR” appears.  
“N/A CHANNELS” appears.  
“NO ACCESS” appears.  
iPod which does not support the tag memory is connected.  
The procedure is not registered to TAG Memory function  
No receivable channel and category.  
The procedure preset with mixed preset memory function cannot be available. The  
preset content may not be recalled depending on the selected band or source.  
36 English  
Specifications  
FM tuner section  
Bluetooth section (KDC-BT648U/  
KDC-X695 only)  
Technology: Bluetooth Ver. 2.0 Certified  
Frequency: 2.402 – 2.480 GHz  
Output Power: +4 dBm (MAX), 0 dBm (AVE)  
Power Class 2  
Maximum Communication range:  
Line of sight approx. 10m (32.8 ft)  
Profile:  
Frequency range (200 kHz space):  
87.9 MHz — 107.9 MHz  
Usable sensitivity (S/N= 26 dB):  
11.2 dBf (1 μV/75 Ω)  
Quieting sensitivity (DIN S/N = 46 dB):  
19.2 dBf (2.5 μV/75 Ω)  
Frequency response ( 3 dB): 30 Hz — 15 kHz  
Signal-to-Noise ratio (MONO): 63 dB  
Stereo separation (1 kHz): 40 dB  
HFP (Hands Free Profile),  
SPP (Serial Port Profile),  
HSP (Headset Profile),  
OPP (Object Push Profile),  
PBAP (Phonebook Access Profile),  
SYNC (Synchronization Profile)  
AM tuner section  
Frequency range (10 kHz space):  
530 kHz — 1,700 kHz  
Usable sensitivity (S/N= 20 dB): 31 dBμ (36 μV)  
CD player section  
Audio section  
Laser diode: GaAIAs  
Maximum output power: 50 W × 4  
Full bandwidth power (at less than 1 % THD):  
22 W × 4  
Digital filter (D/A): 8 Times Over Sampling  
D/A converter: 24 Bit  
Spindle speed: 500 rpm — 200 rpm (CLV)  
Wow & Flutter: Below Measurable Limit  
Frequency response ( 1 dB): 20 Hz — 20 kHz  
Total harmonic distortion (1 kHz):  
KDC-X695/KDC-X395: 0.008 %  
KDC-BT648U/KDC-348U: 0.01 %  
Signal-to-Noise ratio (1 kHz):  
Speaker impedance: 4 Ω — 8 Ω  
Tone action:  
Bass: 100 Hz 8 dB  
Middle: 1 kHz 8 dB  
Treble: 12.5 kHz 8 dB  
Preout level / load (CD):  
KDC-X695/KDC-X395: 4,000 mV/ 10 kΩ  
KDC-BT648U/KDC-348U: 2,500 mV/ 10 kΩ  
Preout impedance: ≤ 600 Ω  
KDC-X695/KDC-X395: 110 dB  
KDC-BT648U/KDC-348U: 105 dB  
Dynamic range: 93 dB  
AAC decode: AAC-LC “.m4a” files (KDC-BT648U/  
KDC-X695 only)  
MP3 decode: Compliant with MPEG-1/2 Audio  
Layer-3  
Auxiliary input section  
Frequency response ( 3 dB): 20 Hz — 20 kHz  
Input maximum voltage: 1,200 mV  
Input impedance: 10 kΩ  
WMA decode: Compliant with Windows Media  
Audio  
General  
Operating voltage:  
KDC-BT648U/KDC-X695: (10.5 V — 16 V allowable):  
USB interface  
14.4 V  
USB standard: USB1.1/ 2.0 (Full speed)  
Maximum supply current: 500 mA  
File system: FAT16/ 32  
KDC-X395/KDC-348U: (11 V — 16 V allowable):  
14.4 V  
Maximum current consumption: 10 A  
Installation size (W × H × D):  
182 mm × 53 mm × 160 mm  
(7-3/16” × 2-1/16” × 6-5/16”)  
Weight: 2.9 lbs (1.3 kg)  
AAC decode: AAC-LC “.m4a” files (KDC-BT648U/  
KDC-X695 only)  
MP3 decode: Compliant with MPEG-1/2 Audio  
Layer-3  
WMA decode: Compliant with Windows Media  
Audio  
Subject to change without notice.  
English 37  
FCC WARNING  
IC (Industry Canada) Notice  
Operation is subject to the following two  
conditions:  
This equipment may generate or use radio  
frequency energy. Changes or modifications  
to this equipment may cause harmful  
interference unless the modifications are  
expressly approved in the instruction manual.  
The user could lose the authority to operate  
this equipment if an unauthorized change or  
modification is made.  
(1) This device may not cause interference, and  
(2) this device must accept any interference,  
including interference that may cause  
undesired operation of the device.  
The term “IC: ” before the certification/  
registration number only signifies that the  
Industry Canada technical specification were  
met.  
FCC NOTE  
This equipment has been tested and found  
to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide  
reasonable protection against harmful  
interference in a residential installation. This  
equipment may cause harmful interference  
to radio communications, if it is not  
installed and used in accordance with the  
instructions. However, there is no guarantee  
that interference will not occur in a particular  
installation. If this equipment does cause  
harmful interference to radio or television  
reception, which can be determined by  
turning the equipment off and on, the user is  
encouraged to try to correct the interference  
by one or more of the following measures:  
Note de ‘IC (Industrie Canada  
L’utilisation de ce dispositif est autorisée  
seulement aux conditions suivantes:  
(1) Il ne doit pas causer d’interférence, et  
(2) l’utilisateur doit accepter tout brouillage,  
y compris les interférences pouvant  
compromettre le fonctionnement de cet  
appareil.  
L’expression “IC: ” avant le numéro  
d’homologation/enregistrement signifie  
seulement que les spécifications techniques  
d’Industry Canada ont été respectées.  
2CAUTION  
Use of controls or adjustments or performance  
of procedures other than those specified  
herein may result in hazardous radiation  
exposure.  
In compliance with Federal Regulations,  
following are reproductions of labels on, or  
inside the product relating to laser product  
safety.  
■
Reorient or relocate the receiving antenna.  
Increase the separation between the  
■
equipment and receiver.  
Connect the equipment into an outlet on  
■
a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/  
■
TV technician for help.  
Kenwood Corporation  
2967-3, ISHIKAWA-MACHI,  
HACHIOJI-SHI  
■
Contains Transmitter Module  
FCC ID : RKXCK5000NVIA  
Contains Transmitter Module  
TOKYO, JAPAN  
■
IC : 5119A-CK5000NVIA  
KENWOOD CORP. CERTIFIES THIS EQUIPMENT  
CONFORMS TO DHHS REGULATIONS N0.21 CFR  
1040. 10, CHAPTER 1, SUBCHAPTER J.  
Location : Top Panel  

Sierra 730 User Manual
Samsung Aw0891m User Manual
Radio Shack Tad 277 User Manual
Panasonic Cs Xe12ckr User Manual
LG ARISTO LG MS210 02 User Manual
LG 47LY760H User Manual
Lexmark Dn2 User Manual
HITACHI CP X4022WN User Manual
DELL U2713H User Manual
BLAUPUNKT CARACAS 110 User Manual