OWNER’S MANUAL AND INSTALLATION GUIDE
SD - X SERIES (Included SD30, SD33,SD39,SD45, S14W)
IMPORTANT INSTRUCTIONS
WARNING
You should read and always follow the important instructions below to reduce the risk of fire, electric
shock, and injury to persons.
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces, such as
surfaces near the heater outlet or light bulbs. The grill directly in front of the heater outlet becomes
hot during heater operation. If provided, use handles when moving this heater.Keep combustible
materials, such as clothes, pillows, furniture, bedding, papers and curtains at least 3 feet from the
front of the unit and keep them away from the sides and rear. Do not cover or block heater outlet
or any ventilation or exhaust opening at any time. Do not use on soft surfaces where openings may
become blocked.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Do not install the heater directly on carpet or a similar surface, which may restrict air circulation
beneath the unit.
5. Always unplug heater when not in use.
6. To disconnect heater, turn controls to off, then remove plug from outlet.
7. Do not use outdoors.
8. This heater is not intended for use in wet locations, such as bathrooms, laundry areas and similar
indoor locations. Never locate heater where it may fall into water container.
9. Do not operate the heater with a damaged cord or plug, or if the heater has malfunctioned, or if the
heater has been dropped or damaged in any manner. Discard heater, or Return heater to
authorized service for examination, adjustment or repair.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange
cord away from traffic area and where it will not be tripped over.Do not route cord under furniture
or appliances
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the heater.
12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
Front view
upper view
175mm
Air inlet
360mm
50mmm
Air outlet
250mm
13. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to
flammable vapours.
14. Do not modify this heater. Use it only as described in this manual. Any other use not recommended
by the manufacturer may cause fire, electric shock or injury to persons.
15. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
16. Do not burn wood or other materials in this heater.
17. Do not strike heater glass.
18. Always use a certified electrician should new circuits or outlets be required.
19. Always use properly grounded, fused and polarized outlets.
20. Always use ground fault protection where required by electrical code.
21. Always disconnect power before performing any cleaning, maintenance or relocation of the heater.
22. When transporting or storing the heater and cord, keep in a dry place, free from excessive vibration
and store so as to avoid damage.
23. The heater must not be located immediately below a socket-out.
24. WARNING: In order to avoid overheating, do not cover the heater.
25. This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
26. Children should be supervised to ensure that they do not play with the appliance.
27. Indoor and household use.
SAVE THESE INSTRUCTIONS
Grounding instructions
This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 1. An adapter as
shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles.
The green grounding lug extending from the adapter must be connected to a permanent ground such
as a properly grounded outlet box. The adapter should not be used if a three-slot grounded
receptacle is available.
Figure 1
INSTALLATION
This section provides step-by-step instructions for installation of your heater.
WARNING
The outlet must be 15A/120V.
CAUTION
Do not remove the four rubber feet at the bottom of the heater or install the heater directly on soft
surfaces, which may restrict air circulation. Otherwise, it may cause a risk of fire or damage.
1. Select a suitable location, which is not susceptible to moisture, safe, dust free, away from high traffic and
away from things may catch fire or block openings such as drapes, furniture, etc.
NOTE
This heater is for household use only.
It is a good idea to place your heater near an existing outlet, for ease of electrical hook up.
2. Place the heater in the desired location to see how it will look in the room.
3. The size of ADL-2000M-SD33 is: 77cm (Wide) ×69cm (High) ×18cm(Deep）
The size of ADL-2000M-SD39 is: 91cm (Wide) X80cm (High) X 18cm(Deep)
The size of ADL-2000M-SD45 is: 108cm(Wide) X81cm (High) X 20cm(Deep)
The size of ADL-2000M-S14W is:140cm(Wide) X76cm (High) X 36cm(Deep)
4. If there's no 15A/120V outlet near the desired location, install a new one .
WARNING
Do not attempt to wire you own new outlets or circuits. To reduce the risk of fire, electric shock
or injury to persons, always use a licensed electrician.
5. Make sure the heater is switched off (refer to operation instruction section).
6. Plug the heater into a 15A/120V outlet. Wiring the cord along the corner of wall.
Plug must be accessible after installation.
OPERATION
This section will explain the function of each convenient control.
NOTE
The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused
by initial heating of internal heater parts and will not occur again.
Control Panel Operation
A. Buttons and indicators
There are four buttons on the remote controller, and four on the control panel of the heater, each
pair of buttons with the same label perform the same function, the back of it is manual switch near
the power cord:
<ON/OFF> button is power switch of the heater;
<DIMMER> button is used to adjust the brightness of simulated flame and logs;
<LOW> button turns the heater on and switches it to low-power status. If the heater already working
at low-power status, to push this button will turn the heater off
<HIGH> button turns the heater on and switches it to high-power status. If the heater already
working at high-power status, to push
this button will turn the heater off;
There are four indicators on the control panel:
is the power indicator, it light up when the
heater is working, and turned out when
the heater is turned off;
indicates the status of the simulated
flame and logs. It's brighten up when the
flame simulate component is working,
and will be flashing when you adjusting
the brightness of the flame;
indicate the heater is working in low-
power status;
indicate the heater is working in high-power status.
The red window on the control panel of heater is the eye of receiver, do not cover.
B. Operation
On the first usage of remote controller, install the batteries first: open the battery box by sliding its cover
along the arrow, install two AAA batteries according to the marks in the box, and slide the cover to its
original position. If no batteries installed or the batteries are failure, the remote controller will be unusable.
To use the remote controller effectively, point it to the electric fireplace and keep a distance of 1-5 meters.
There're four buttons marked the same as buttons on the remote controller, each pair of them perform the
same function, choose as you favour.
1. Power control. Press the <ON/OFF> button, the heater will be powered on, and the
lamp will
brighten up. The heater will not be turned on automatically when you power on the heater,
please refer to paragraph 3. Note, all operations are valid only when the power is on, except to
"turn the power on" operation. Press the <ON/OFF> button again, the heater will be powered off.
2. Adjust the brightness of simulated flame and logs. When the heater is powered on, flame is
turned on automatically, and it is as bright as when the heater is powered off. Press <DIMMER>
button to adjust the brightness, the
logs will start and keep changing. When the brightness goes to the point you want, press
<DIMMER> button again, and the brightness will keep still and the lamp will keep brighten up.
3. Heater control. Lamp and indicates the status of heater. It's working in low-power status
is brighten up, in high-power status when is brighten up, turned off when both of
is dark. When the heater is not in low-power status ( is dark), press <LOW> button will
lamp will be flashing, and the brightness of the flame and
when
and
switch it to low-power status; when it's in low-power status ( is brighten up), press <LOW>
button will turn it off. Similarly, a <HIGH> button press will switch the heater to high-power status
when is dark, and turn it off when is brighten up.
Note, before the heater emits heat or after it stop producing heat, the hot air outlet may output air
for 10 seconds. This is designed for protect circuit, and it's not spoiled.
4. Power off the heater when you leave it for a long time.
5. The two alkaline batteries must be removed from the appliance before it is scrapped.
6. The alkaline battery is to be disposed of safely.
7. Roll up the power cord in the supports when the heater is not in use.If your select to store your
heater fully assembled, be sure to cover it, to protect it from accumulating dust.
8 Temperature Limiting control will automatically disconnect from power when reach a certain
temperature，then unplug the power，When the temperature falls ，the thermostat will be
restored ，connect the plug to power，heater will work.
MAINTENANCE
WARNING
Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric
shock to persons or damage.
Light Bulb Replacement
Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity
and detail of the log exterior disappears. There are two bulbs under the log set for ADL-2000M
–SD45
WARNING
Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid burning of skin.
Except the light bulb replacement, any other servicing should be performed by an authorized service
representative.
I. Bulb Requirements
Quantity of 4 clear chandelier or candelabra bulbs with an E-12 small socket base, rating voltage
120 volts, rating power 40 watts.
CAUTION
Do not exceed 40 watts per bulb
II. Operation
1. Open the light bulb area:
The light bulb area is at the back of electric fireplace, see ”E” .there are 6 screws on it.loosen the
screw by some tool,then you can open it. (Right figure)
2. Examine the bulbs to determine which bulbs require replacement.
3. Remove old bulb and replace a new one. Hold the socket while unscrewing or screwing bulbs.
(Right figure)
4. Replace the cover of light bulbs.
5. Done.
Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Dynasty Fireplaces
#10 – 3071 No. 5 Road, Richmond, BC V6X 2T4
Tel.: 1-877-521-1009 Toll Free / (604) 821-1009 Fax: (604) 821-1019
|