Item #1000 510 665
Model #YJAF052-Tan
USE AND CARE GUIDE
11 FT SOLAR UMBRELLA OFFSET-TAN
Questions, problems, missing parts? Before returning to the store
call Hampton Bay Customer Service.
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this umbrella. We strive to continually create
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!
Pre-Assembly
PLANNING ASSEMBLY
Read all instructions before assembly.
To avoid damaging this product, assemble it on a soft, non-
abrasive surface such as carpet or cardboard.
NOTE: More than one person may be required to
complete the assembly of this product.
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
AA
BB
CC
DD
FF
EE
Part
AA
Description
M8x20 Hex bolt
M8 Washer
M5x8 Bolt
Quantity
4+1
BB
CC
DD
EE
FF
4+1
2+1
1
Wrench
1
Hex wrench S3
Hex wrench S4
1
3
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Pre-Assembly (continued)
PACKAGE CONTENTS
E
F
G
D
I
H
N
N
H
C
M
K
L
J
J
K
L
M
K
K
B
A
Part
Description
Quantity
Part
Description
Quantity
A
Lower bracket
1
1
Upper base cover
I
Upper bracket
Lower umbrella pole
1
1
2
4
B
C
J
K
Support tube rim
Corner connector
Side panel
1
1
D
E
Locking knob
Solar receiver
2
2
L
M
Lock panel
1
1
Crank
Sand bag
F
G
H
1
N
Umbrella shade
Lower base cover
2
4
Assembly
Attaching the brackets
1
Attach the upper bracket (B) onto the lower bracket (A).
NOTE: This umbrella should be set up in its desired
location to avoid moving it after assembly.
B
A
5
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Attaching the lower umbrella pole to the brackets
2
Attach the lower umbrella pole (C) to the upper bracket (B) and lower bracket (A) using M8x20 hex bolts (AA)
and M8 washers (BB).
NOTE: Fully tighten all bolts using the wrench (DD).
C
DD
AA
BB
B
A
6
Assembly (continued)
Inserting the corner connectors
3
Insert the corner connectors (K) into the four ends of the assembled brackets.
K
K
K
K
K
7
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Sliding the lock panels
4
Slide the perforated lock panels (M) downward between the corner connectors (K).
M
K
K
M
K
K
8
Assembly (continued)
Sliding the side panels
5
Slide the side panels (L) downward between the corner connectors (K).
Connect the two pieces of the support tube rims (J).
Slide the support tube rims (J) down the lower umbrella pole (C) and connect it to the brackets (A and B).
J
2
C
K
J
K
L
L
B
A
1
K
K
M
9
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Placing the sand bag
6
Place the sand bag (N) in the umbrella base.
NOTE: Place the base in the area where the umbrella
is to be used. The umbrella will be very heavy after
filled with sand.
N
10
Assembly (continued)
Filling the sand bag
7
Pull to open the velcro pouch on the sand bag (N) and fill with sand.
After filling the sand bags (N), close the pouch and ensure the velcro is sealed.
Lock the two sections of the sand bags (N) together.
NOTE: The sand bags (N) are to be filled with sand only.
NOTE: For proper stability of the offset umbrella,
please place 110 lbs of sand into each sand bag for
a total of 220 lbs.
2
1
N
11
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Ensuring the locking mechanism is in the open position
8
Ensure the locking mechanism on the lock panel (M) is in the OPEN position by using the wrench (DD) as shown in figure 1.
Ensure the locking mechanism on the lower base cover (H) is in the OPEN position by using the wrench (DD) as shown in figure 2.
Attach the lower base cover (H) to the side panels (L).
Close the lower base cover (H) and ensure they are fully closed.
1
2
DD
DD
CLOSE POSITION
CLOSE POSITION
DD
DD
OPEN POSITION
OPEN POSITION
H
L
M
12
Assembly (continued)
Locking the lower base cover
9
Lock the lower base cover (H) and the lock panel (M) by turning the locking mechanisms to the CLOSE position using
the wrench (DD) as shown in figure 1 and figure 2.
Attach the upper base cover (I) to the assembled base.
1
2
DD
DD
OPEN POSITION
OPEN POSITION
1
2
I
3
CLOSE POSITION
CLOSE POSITION
H
M
13
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Attaching the locking knob to the lower umbrella pole
10
Attach the locking knob (D) to the lower umbrella pole (C) using the M5x8 bolts (CC) and hex wrench S3 (EE). Make sure the
locking knob (D) is placed as shown in figure (1) before attaching.
NOTE: When inserting the locking knob (D) into the hole,
make sure the two points of the locking knob fit into
the two slots on the umbrella pole as shown below.
(1)
(2)
EE
1
2
D
C
CC
14
Assembly (continued)
Preparing the umbrella
11
Push the long bent tube of the umbrella shade (G) outwards a little while holding down the tap on the short bent tube to
make the hinge slide to snap into place as shown below.
G
15
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued)
Attaching the solar reciever
12
Attach the solar receiver (E) to the umbrella shade (G) by turning the solar receiver (E) clockwise until
fully tightened.
Insert the plug into the plug hole of the solar receiver (E).
NOTE: Please leave the solar receiver (E) out in a sunny
area to charge before the first time turning on the LED
lights.
E
1
E
2
G
16
Assembly (continued)
Inserting the umbrella shade into the lower umbrella pole
13
Rotate the locking knob (D) 180 degrees clockwise as shown in figure 1.
Insert the umbrella shade (G) into the lower umbrella pole (C) as shown in figure 2.
Rotate the locking knob (D) 180 degrees clockwise as shown in figure 3.
NOTE: If there is a gap in the locking knob (D) as
shown below in figure 3, please rotate the umbrella
shade (G) until it is completely locked as shown
in figure 4.
1
G
3
G
2
D
C
C
4
17
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Operation
Attaching the crank
1
Attach the crank (F) to the handle as shown in figure (1).
Attach the crank (F) by aligning the tap with the hole on the crank (F) until it snaps into place.
To detach the crank, the wrench (FF) is required to press the tap to take the crank (F) out.
Attach the crank (F) without using the tap as shown in figure (2).
To detach the crank (F), just take the crank out.
NOTE: Both methods of attaching the crank (F)
are acceptable.
1
(1)
F
2
FF
1
(2)
F
2
18
Operation (continued)
Raising the umbrella
2
Loosen the knob on the umbrella shade as shown in figure 1 by turning it counterclockwise until it is fully loose.
Hold the umbrella handle and push the long bent tube upward as shown in figure 2 until it stops and the umbrella is fully extended.
Fully tighten the knob on the umbrella shade clockwise as shown in figure 3 to lock the handle in place.
1
2
3
19
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Operation (continued)
Opening the umbrella
3
Undo the Velcro belt on the canopy and shake the canopy to separate the umbrella ribs.
Slowly turn the crank (F) clockwise to open the umbrella.
When the umbrella is fully open, fasten the belt under the hinge of the short bent tube to stabilize the umbrella. Make sure the belt is
tighten as shown in figure 3.
1
2
F
3
20
Operation (continued)
Operating the umbrella
4
Rotate the locking knob (D) 180 degrees clockwise as shown in figure 1.
Hold the umbrella handle with one hand and hold the short bent tub with the other hand to rotate the umbrella as shown in figure 2.
(The umbrella can rotate up to 360 degrees.)
When the umbrella is at the desired position, rotate the knob 180 degrees clockwise as shown in figure 3.
Rotate the umbrella shade (G) untill the locking knob (D) automatically secures as shown in figure 4.
1
2
3
G
4
D
21
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Operation (continued)
Operating the umbrella
5
Press the ON/OFF switch to turn the LED light on and off.
Fully loosen the knob on the umbrella shade (G) by turning it counterclockwise, then slide the umbrella handle down to adjust the angle
of the umbrella.
When the umbrella is at the desired angle to shade the sunlight, fully tighten the knob by turning it clockwise.
1
ON/ OFF
2
3
4
22
Operation (continued)
Closing the umbrella
6
Loosen the velcro belt as shown in figure 1.
Turn the crank counterclockwise to close the umbrella as shown in figure 2.
When the umbrella is closed, fully loosen the knob on the umbrella shade (G) by turning it counterclockwise as shown in figure 3.
Hold the handle and pull the long bent tube downward as shown in figure 4.
Tighten the knob on the umbrella shade (G) by turning clockwise as shown in figure 5 after closing the umbrella.
NOTE: To adjust the umbrella shade to the original position before closing, follow these steps:
- Fully loosen the knob on the umbrella shade by turning it counterclockwise.
- Slide the handle on the long bent tube upwards.
- When the long bent tube is pushed to the top, fully tighten the knob by turning it clockewise.
1
2
3
4
5
23
HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Operation (continued)
Storing the umbrella
7
Tie the umbrella to the umbrella pole with the Velcro belt when not in use as shown below.
Care and Cleaning
For best results, clean the frame and fabric with a damp cloth, and dry thoroughly. This will help prevent mildew by removing dirt
particles that may accumulate.
Do not clean with abrasive materials, bleach, or solvents.
Store the umbrella in a dry, sheltered place when not in use.
Tie the canopy closed on windy days to prevent damage to the umbrella.
Keep the umbrella away from fire, extreme heat, freezing conditions, and inclement weather such as rain, hail, sleet, snow, or wind.
24
Questions, problems, missing parts? Before returning to the store
call Hampton Bay Customer Service.
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.
|