f650x
Car Camcorder
User Manual
About this Guide
The content in this document is for information purpose and is subject to
change without prior notice. We have made every effort to ensure that
this User Guide is accurate and complete.
However, no liability is assumed for any errors or omissions that may
have occurred.
The manufacturer reserves the right to change the technical
specifications without prior notice.
Regulatory notices
This document provides country- and region-specific non-wireless and
wireless regulatory notices and compliance information for your product.
Some of these notices may not apply to your product.
Prohibition of co-location
This device and its antenna(s) must not be co-located or operated in conjunction
with any other antenna or transmitter.
WEEE Notice
Disposal of Waste Electrical and Electronic Equipment and/or Battery
by users in private households in the European Union
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of
materials will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health
and environment.
3
CE Regulatory Notice
The product herewith complies with the requirements of the Low Voltage
Directive 2014/35/EU, the EMC Directive 2014/30/EU, the RED-Directive
2014/53/EU and the RoHS Directive 2011/65/EU.
EU Health Protection: This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Notes on Installation
1. Please measure the front windshield viewing area, make sure not to
block driver's front view, install the camcorder below the rearview
mirror (the central, higher right position of the front windshield). And
we recommend that the sky and the land occupied by the screen
50%, fix the car holder and then adjust the camcorder so that the
lane is aligned with the screen. Proper installation enables the
camcorder to maximize the efficiency also can enhance the accuracy
of LDWS.
2. Make sure that the lens is within the wiping range of the windscreen
wiper to ensure a clear view even when it rains.
3. Do not touch the lens with your fingers. Finger grease may be left on
the lens and will result in unclear videos or pictures. Clean the lens
on a regular basis.
4. Do not install the camcorder on a tinted window. Doing so may
damage the tint film.
5. Make sure that the installation position is not hindered by the tinted
window.
6. This product is suitable for light windshield or light color
heat-resistant film windows , it will affect video quality if install it on
the dark windows or dark heat-resistant film windows.
7. Use the products of the attached power charger only, please do not
use other brand power charger, in order to avoid equipment burn or
cause the battery explosion.
Caution
Due to local laws and vehicles safety considerations, do not
operate the camcorder while driving.
Set up time zone, time and date accurately before you use this
camcorder.
Please use SuperCar software under the condition that Electronic
Map are functioning normally.
4
The firmware function in the camcorder is for reference only,
drivers are advised to exercise discretion based on actual road
conditions.
The results of GPS positioning are only for reference, and should
not affect the actual driving situation. The camcorder also cannot
ensure the positioning accuracy.
GPS positioning accuracy may differ depending on weather and
location such as high buildings, tunnels, undergrounds, or forests.
GPS satellite signals cannot pass through solid materials (except
glass). Tinted window will also affect the performance of the GPS
satellite reception.
GPS reception performance on each camcorder may differ. The
camcorder cannot determine the accuracy of the positioning results
from different hardware.
The values displayed in this camcorder, such as speed and
position, may be inaccurate due to the influence of surrounding
environment. They are for your reference only.
This product is used only for non-commercial use, within the
maximum limits permitted by applicable law. We do not take any
responsibilities for the loss of use of the product.
This camcorder gets warm when in use; this is normal.
Improper use or operation of the product may result in damage of
the product or its accessories and void the warranty.
Wi-Fi Signals are unable to pass through the building. The upper
limit of signal transmission is 5m.
Wi-Fi Operation Channel: Ch1~Ch13
The product employs wireless data communication which may
interfere, or be interfered by, a near-by camcorder.
Never use this camcorder in the vicinity of a microwave oven or at
places where there is radio interference.
Radio wave reception may be worsened in specific environments.
Please be advised that if another camcorder is also using the same
2.4GHz band as this product, the processing speed of both
camcorders may slow down.
This product gets warm when in use; this is normal.
Improper use or operation of the product may result in damage of
the product or its accessories and void the warranty.
The radio frequency (RF) generated by this RF electronic camcorder
may cause adverse effects on the operation of other electronic
5
camcorders and result in malfunctioning. Wireless transmitters and
circuitry may also interfere with other electronic camcorders.
Therefore, do observe the following precautions:
Aircraft: Never use a radio transmitter when you are in an
airplane. Please switch off the Wi-Fi function of the
camcorder.
Vehicle: The radio frequency transmitted by this camcorder
may affect the electronic system in a motorized vehicle.
Please consult the manufacturer or dealer of your vehicle on
the possible effect.
Pacemaker: In order to prevent any potential interference to a
pacemaker, anyone who uses a pacemaker should be advised,
that, when using this camcorder, a minimum distance of 15cm
(6 inch) should be kept between the camcorder and the
pacemaker; and never put this camcorder in a chest pocket. In
case of any doubt of interference, switch off the camcorder
immediately.
Medical Camcorder: If you use a personal medical camcorder,
consult the camcorder manufacturer or your physician to
confirm if your camcorder is sufficiently shielded from the RF
transmission of this camcorder.
Medical Facilities: Hospitals and medical institutes may use
facilities that are sensitive to an external RF energy. Observe
such instructions when the medical care personnel or any
posted sign requests you to switch off any camcorder that
may interfere the radio frequency.
Explosion sites or any location with a posted sign: In order to
prevent interfering with an explosion activity, observe all the
signage and instructions in the Explosion Area or in a zone
with a “Switch Off 2-way Radios” sign by switching off
camcorders that may interfere with the radio frequency.
HP Inc. is NOT responsible for the loss of any data/content during
operation.
Before you start using the system, it is assumed that you
agree to the above statement.
6
1 Introduction
Thank you for purchasing this advanced Car Camcorder. This product is
specifically designed for real time video recording when driving.
1.1 Features
Full HD 1920*1080
2.0" TFT-LCD color screen
150° Wide angle lens
Collision Detection, when a collision is detected, the camcorder will
automatically trigger the emergency recording
Parking Mode
Multifunction traffic safety reminder
1.2 Package Contents
The package contains the following items. In case there is any missing or
damaged item, contact your dealer immediately.
Electrostatic
sticker
Car camcorder
CD-ROM
Quick start guide
Car charger
7
1.3 Product Overview
No.
Item
No.
Item
1
2
3
4
5
LED Indicator
8
9
Speaker
Wide Angle Lens
LCD Color Screen
Menu / Back Button (
Playback / Up Button (
Snapshot / Down Button (
/
)
10 Microphone
/
)
11 Power Button
12 Power Connector Port
13 Memory Card Slot
14 Bracket Knob
/
)
Emergency Recording / Confirm
Button (
6
/
)
7
Voice Record on/off (
)
Note:
Please press the button (3~7) according to the diagram notice shown on screen.
8
2 Getting Started
2.1 Storage Media
2.1.1 Insert the Memory Card
Insert memory card with the pins facing forward and the screen of the
camcorder facing forward too, see the picture as below:
2.1.2 Remove the Memory Card
If the camcorder is power on, please power off first and wait for the
procedure of switching off the camcorder completed before removing
the memory card.
Note:
1. Do not remove or insert the memory card when the camcorder is turned on. This may damage the
memory card.
2. Support SDHC class 10 and memory storage 8GB or above (support up to 32GB).
3. Please format the micro SD cards before the initial use. The formatted file type for this camcorder
is FAT32 file.
4. Periodically format the microSD card (recommended period: once a month).
9
2.2 Installing in Vehicles
2.2.1 Mount to Windshield
1.
Put the electrostatic sticker onto the suggested area on the
windshield. Before putting the sticker, please wipe and clean the
windshield. During the installation, please make sure the bubbles
in between the sticker and the window are all gone.
2.
Peel off the protective plastic sheet from the adhesive pad.
10
3.
Place and press the bracket firmly onto the electrostatic sticker on
the windshield window. Make sure the base is securely locked in
place.
2.2.2 Adjust the Camcorder
1. Loosen the knob to swivel the camcorder to adjust view angle.
2. Then tighten the knob to make sure the camcorder is securely
locked in place.
11
2.3 Connecting to Power
Use only the supplied car charger to power up the camcorder.
1. Connect one end of the car charger to the USB connector of the
camcorder. USB port input: DC 5V / 1A.
2. Plug the other end of the car charger to the cigarette lighter socket
of your vehicle. Once the vehicle engine is started, the camcorder
automatically powers on. Car charger input: DC 12 / 24V.
2.4 LED Indicator
Status Explanation
LED Indicator Color
Red
Power off, connect
external power
Power on, standby
Green
Recording/ Recording
and screen off
Flash red
12
2.5 Powering the Camcorder On / Off
2.5.1 Auto Power On/Off
Start the car engine, wait a few seconds to charge the camcorder, and
then screen will light up and the camcorder will automatically power on
and start recording.
Once the vehicle engine shuts down, the camcorder automatically saves
the recording and turns off the power.
2.5.2 Manual Power On/Off
To manually turn on the power, press the POWER button.
To turn off, press and hold the POWER button for at least 2 seconds.
2.5.3 Reset
Press and hold the Power button for 8 seconds to reset the device.
13
2.6 Initial Settings
Before using the camcorder, we recommend you setup the correct Time
zone, Date and Time.
Note:
Please note that if you press the
button during recording, the system will stop recording and
enter OSD menu. Make sure the recording is already stopped then continue operating the menu.
2.6.1 Set Time Zone
To set the time zone, do the following:
1. Press the
button to enter the OSD menu.
2. Press the
or
button to select Set Time Zone, and then
press the
button for entering function menu.
3. Press the
or
button to set the current time zone, and
button to complete setting.
button to return to recording screen.
then press the
4. Press the
Note:
1. If Time Sync. is on, camcorder clock will be calibrated via satellite clock signal based on Set Time
zone.
2. If satellite positioning is not successful, camcorder clock will run based on user defined time.
14
2.6.2 Set the Date / Time
To set the correct date and time, do the following:
1. Press the
button to
enter the OSD menu.
2. Press the
or
button to select Date / Time,
and then press the
button for entering function
menu.
3. Press the
or
button to adjust the value, and then press the
the next field.
button to set
4. Repeat step 3 until the date and time setting is completed.
Note:
To ensure the accuracy of the video file time, please reset the date and time when not in use over 7
days.
15
3 Using the Car Camcorder
3.1 Automatic Record
Start the car engine, wait a few seconds to charge the camcorder, and
then screen will light up and the camcorder will automatically power on
and start recording.
Recording will automatically stop when the engine is switched off.
Note:
1. Some vehicle power supply would not turn on / off automatically with the car engine start, if the
camcorder cannot automatically power on/off with the car engine, please manually connect the
power supply with the vehicle power, and then power on, or manually power off the camcorder and
then release the connector with the car power supply.
2. It can be configured to save a video file for every 30 seconds, 1 or 3 minutes of recording.
3. All the videos and photos are saved in the memory card, if memory card is full, loop recording will
generally overwrite the oldest video file.
4. The camcorder is built-in super capacitor. After start the car engine, please wait a few seconds for
charging the camcorder, and then the camcorder will automatically power on and start recording.
16
3.1.1 The Recording Screen
No.
Icon
Item
Description
1
Recording Duration
Indicates the video current duration.
Indicates the current recording date
and time.
2
3
Date / Time
During video recording, press the
button to enter the OSD menu.
Menu Button
During video recording, press the
button to add a speed cam
point.
Add Speed Point
Button
4
5
PIV (Picture in
Video) Button
Press
to capture video screen
shots from the front camera.
During video recording, press the
button to enter emergency
recording mode.
Emergency
Recording Button
6
17
7
8
Voice Record on/off Turn on/off voice recording.
Resolution
Indicates the video resolution.
icon
Voice Record
icon
Indicates voice recording sets as off,
the sound will not be recorded.
9
Indicates the strength of satellite
positioning. If the icon shows in red
on screen, it indicates that the
camcorder cannot complete the
satellite positioning.
Satellite Positioning
icon
10
Indicates camcorder is connected
with power.
11
12
Power icon
Wi-Fi
Wi-Fi on
Wi-Fi off
18
3.1.2 Emergency Recording
To Start the Emergency Recording, do the following:
1. During Video Recording, press
the
button to enter
emergency recording mode,
the “Emergency” message
will be shown immediately on
the upper left corner of the
screen, and the recorded file
will be protected.
2. The emergency video
recording length is same as the recording interval setting. When the
emergency recording length reaches the setting, the system will
return to the general recording mode.
Note:
1. If the Collision Detection function is enabled and a collision is detected, the camcorder will
automatically trigger the emergency recording.
2. The emergency file is created as a new file and saved in Emergency folder, which will be protected
to avoid being overwritten by normal loop recording. The Emergency folder will occupy 40% of
available memory card capacity. For example, if you use 8GB memory card, about 3.2GB memory
space will be saved for emergency files. When the Emergency folder is full, the oldest emergency file
will be automatically deleted by the newest emergency file.
3.2 Add Speed Point
You may customize speed cam positions in this product.
1. When the GPS positioning is completed , press
camera points.
to update speed
2. This product features a capacity of 50 speed cam positions. In case
you are trying to add more than that, the system prompts with
message "Speed Position is full".
Note:
You may delete custom speed cam positions by selecting the Delete Last Position or Delete All
Position option from the Speed Position Management menu. Please note that all of your existing
speed cam positions are deleted once the Delete All Position option is selected. Make sure you are
ready to recreate your custom speed cam positions before running this option.
19
3.3 Picture in Video
You can also use this camcorder to take snapshots of the current scene.
1. In recording status, press
to capture recording
screen shots from the front
(and rear) lens.
2. When the icon
shows
in the central of screen, it
means the screenshots is
completed.
Note:
1. The screen shots image resolution quality is depending on the video resolution setting.
2. The picture resolution is limited by the speed of the target object and changes in ambient lighting.
The photograph function is better used for taking still pictures in accident scenes or when the car is
stopped to wait for a traffic light.
3.4 Driving Safety
The following driving safety function is for reference only. Drivers are advised
to exercise discretion based on actual road conditions.
Note:
1. The Driving Safety function is limited to triggering no more than two alarms at the same time. If a
voice and alert message have been triggered, any other alarm will be ignored until either of the two is
settled.
2. Satellite positioning must be completed before functions such as Speed Cam Alert, Speed Position
Management, Speed Limit Alert, LDWS, FCWS and FCMD to be enabled. Be sure to check that Satellite
positioning has been completed prior to using the product.
3. The detections of LDWS, FCWS and FCMD may be inaccurate when used in rain, at night or in
environments of insufficient lighting. Drivers are advised to exercise discretion based on actual road
conditions.
20
3.4.1 Speed Cam Alert
If the Speed Cam Alert function is enabled, once your car’s location is
determined by GPS and approaches a speed cam, this product produces
audible alert and screen message.
To enable the Speed Cam Alert, do the following:
1. Press the
enter the OSD menu.
2. Press the
button to
/
button
to select Speed Cam Alert,
and then press the
button for entering function
menu.
3. Press the
/
button
to select On, and then press
the
button to enable the function.
button to return recording screen.
4. Press the
5. The alarm screen turns red to remind you to slow down if you are
driving faster than the speed limit.
Note:
The speed cam alert function must have the speed cam datum from the country you use. The function
will be void if the product is used in any other countries. Please consult with the shop you purchased if
the function is void. There is no guarantee the speed cam datum will be included for the worldwide
countries.
21
3.4.2 Speed Limit Alert
If the Speed Limit Alert function is enabled, this product produces
audible alert and screen message once your car’s location is determined
by GPS and its running speed exceeds the set limit.
To set the Speed Limit Alert, do the following:
1. Press the
button to
enter the OSD menu.
2. Press the
/ button to
select Speed Limit Alert,
and then press the
button for entering function
menu.
3. Press the
/
button
to set up a Speed Limit Alert
to trigger this product’s alarm [Off / 50 ~ 200 km/h (30~125 mph)],
and then press the
4. Press the
button to complete setting.
button to return recording screen.
5. The screen pops up red icon to remind you to slow down when you
are driving faster than the set speed limit.
22
3.4.3 Driver Fatigue Alert
If the Driver Fatigue Alert function is enabled, this product produces
audible alert and screen message one hour after it has begun recording
and repeats the alerts every half hour afterwards.
To enable the Driver Fatigue Alert, do the following:
1. Press the
2. Press the
then press the
3. Press the
button to enter the OSD menu.
/
/
button to select Driver Fatigue Alert, and
button for entering function menu.
button to select On, and then press the
button to enable the function.
4. Press the button return to recording screen.
5. This product produces audible alert and screen message when
Driver Fatigue Alert activates.
3.4.4 LDWS
Once your car’s location is determined by GPS and the LDWS function is
enabled, this camcorder produces audible alert and screen message
when you drive off of or change lanes at speeds over 70 km/h (43 mph).
To set the LDWS (Lane Departure Warning Systems), do the following:
1. Press the
2. Press the
button to enter the OSD menu.
/
button to select LDWS, and then press the
button for entering function menu.
3. Press the
/
button to select On, and then press the
button to enable the function.
4. Press the
button to return to recording screen.
23
5. After enabling LDWS, the screen will display traffic lane align icon
, please adjust the camcorder so that the horizontal line and
the eye level are overlapped and the slash lines are centered in the
driving lane.
6. This product produces audible alert and screen message when
LDWS is activates.
Note:
1. Please measure front windshield viewing area, do not block the driver's forward field of vision, and
install the camcorder below rearview mirror (upper central of the front windshield). We recommend
that the sky and the ground occupied 50 % of the video screen, install the bracket then adjust the
camcorder to make the lane is aligned to the lane alignment icon. Correct installation makes the
camcorder to maximize the efficiency and improve the accuracy of LDWS.
2. Make sure that traffic lane align icon will not be obscured other things (e.g. hood). It may cause
misjudgment if the endpoint is obscured.
24
3.4.5 FCWS
Once your car’s location is determined by GPS and the FCWS function is
enabled, this camcorder produces audible alert and screen message
when you drive at speeds over 60 km/h (37 mph) and are less than 20 m
away from the car in front of you. If the camcorder not completes the
satellite positioning, and the leading vehicle distance below 20 meters, it
will also produce a warning screen and beep reminder.
To set the FCWS (Forward Collision Warning System), do the following:
1. Press the
2. Press the
button to enter the OSD menu.
/
button to select FCWS, and then press the
button for entering function menu.
3. Press the
/
button to select On, and then press the
button to enable the function.
4. Press the
button to return recording screen.
5. This product produces audible alert and screen message when
FCWS is activates.
25
3.4.6 Headlight Warning
The Headlight Warning function produces audible alert and screen
message when it detects poor lighting conditions through the recording
displays of this camcorder, including driving in rainy or cloudy weather,
at night, and in basements, parking lots, and tunnels.
To enable the Headlight Warning, do the following:
1. Press the
button to enter the OSD menu.
2. Press the
press the
/
/
button to select Headlight Warning, and then
button for entering function menu.
3. Press the
button to select On, and then press the
button to enable the function.
4. Press the button to return recording screen.
5. This product produces audible alert and screen message when
Headlight Warning activates.
26
3.4.7 FCMD
If FCMD function is enabled, when the front car moves and you don’t start
to drive forward, the camcorder will issue audible alert and screen
message.
To set the FCMD (Front Car Move Detection), do the following:
1. Press the
2. Press the
button to enter the OSD menu.
/
button to select FCMD, and then press the
button for entering function menu.
3. Press the
/
button to select On, and then press the
button to enable the function.
4. Press the
button to return recording screen.
5. This product produces audible alert and screen message when
FCMD activates.
Note:
The camcorder will detects the front image change to determine FCMD notification alert, so if the car
is in rest condition and front object moves, the camcorder may occur false judgment, and please
judge it according to the actual driving situation.
27
3.5 Parking Mode
To monitor the vehicle when it is parked, you can activate Park Recording,
or Motion and Collision Detection, or Timelapse.
Before you activate Parking Mode, please install ACC cable through
professional car service shop.
Follow the steps below to change the settings for Parking Mode:
1. Press the
2. Press the
press the
button to enter the OSD menu.
/
button to select Parking Mode, and then
button for entering function menu.
button to configure Parking Mode (Park
3. Press the
/
Recording / Motion and Collision Detection / Timelapse/ Off), and
then press the
4. Press the
button to complete setting.
button to return recording screen.
Note: ACC cable is not included in the package. Please ask for more information from your
distributor.
3.5.1 Park Recording
-
In normal recording, press and hold POWER key for 3 seconds, the
screen will show message “Press OK key to power off or enter
Park Recording after 10 sec.” Please wait for 10 seconds and the
camcorder will enter Park Recording automatically. The
camcorder will turn off the screen temporarily, but still in
recording status. Once the collision or vibration is detected, it will
automatically trigger emergency recording.
-
To disable this function, press any key to wake up the screen, and
press again any key to resume to normal loop recording.
Note:
1. The video file taken in this mode is same as normal loop recording mode. It will be saved in the
“Video” folder. And the emergency file will be saved in the “Emergency” folder.
2. The file size is according to Record Interval setting.
28
3.5.2 Motion and Collision Detection
-
In normal loop recording mode, press and hold POWER key for 3
seconds, the screen will show message “Press OK to power off or
enter Motion and Collision Detection after 10 sec.” Please wait
for 10 seconds and the camcorder will enter Motion and Collision
Detection automatically. The camcorder will turn off the screen
temporarily, but still in standby detection status. When the
camcorder detects any motion in front of lens or any
vibration/collision, the video recording will be triggered and the
event will be recorded.
To disable this function, press any key to wake up the screen, and
press again any key to resume to normal loop recording.
-
Note:
1. The video file taken in this mode will be saved in the “Emergency” folder.
2. In this mode, the event will be recorded for 10 seconds (per file). If the event lasts more than
10 seconds, the camcorder will keep recording up to 2 minutes.
3.5.3 Timelapse
-
In normal loop recording mode, press and hold POWER key for 3
seconds, the screen will show message “Press OK to power off or
enter Timelapse after 10 sec.” . Please wait for 10 seconds and
the camcorder will enter Timelapse automatically. The camcorder
will turn off the screen temporarily, but in timelapse recording
status.
-
To disable this function, press any key to wake up the screen, and
press again any key to resume to normal loop recording.
Note:
1. The video file taken in this mode will be saved in the “Video” folder.
2. In this mode, the camcorder is continuously recording by one second one frame. For example,
30 minutes recording will be saved in one minute.
3. The file size is according to Record Interval setting.
29
3.6 Collision Detection
If the Collision Detection function is enabled, this camcorder begins
emergency recording once it detects any collision. Sensitivity of the
Collision Detection function is set to Normal by default, if user wants to
change the settings of Collision Detection, do the following:
1. Press the
2. Press the
then press the
3. Press the
button to enter the OSD menu.
/
/
button to select Collision Detection, and
button for entering function menu.
button to change the sensitivity of this
camcorder’s collision detection (High Sensitivity / Normal
Sensitivity / Low Sensitivity / Off), and then press the
button for entering function menu.
4. Press the
button return to recording screen.
30
3.7 Playback Videos and Photos
1. If recording is in progress,
/
press the
button to stop recording and
enter Menu.
2. Press the
or
button to select Playback and
press the
button.
3. Press the
or
button to select Video, Emergency or Picture category and press
the
button.
4. Use the
or
to select the video or photo you want to
button to confirm your selection.
playback, and press
31
3.8 The Playback Screen
No.
Item
Description
1
File name
File name
Duration/ Total Indicates the video elapse time/ Indicates total recorded
2
3
recorded time
time
Press the
video or picture. Press the
button to return preview screen of
Return
button repetitively to
return recording screen.
Previous File
Button
4
5
6
Press
button to view previous file.
button to view next file.
button to play or pause the video.
Next File Button Press
Playback/ Pause
button
Stamp print
File
Press the
7
8
Indicates date and time stamp
Current file / total file number
32
3.9 Deleting Files
To delete file(s), perform the following steps:
1. Press the
button to stop recording and enter the main Menu.
or button to select File Deletion and
button to confirm.
2. Press the
press the
3. Press the
or
button to select folder and press the
button to confirm. The following options will display in
screen,
Item
Delete One
Delete All
Description
Delete the current selected file.
Deletes all files in this folder.
4. Use the
or
to select the video or photo you want to
button to confirm your selection.
delete, and press
Note:
Deleted files CANNOT be recovered. Ensure the files you wish to preserve are backup before deletion.
33
4 Initial set up Go Dashcam application
4.1 Camcorder application installation
The camcorder allows you to connect to the mobile devices via the App.
When using for the first time, install the [Go Dashcam] App for your
mobile device.
1. Download Go Dashcam App
from Google Play or App Store.
2. Install the App.
APP layout and features may be changed subject to different
software versions. Please refer to Google Play or APP Store
for update.
34
4.2 Wi-Fi connecting
1. Press the Power button to switch on the camcorder.
2. Enter Menu and go to Wi-Fi option; choose “ON” to activate the
wireless network.
3. The camcorder’s screen will display Wi-Fi Device ID and Password.
Using the Wi-Fi function of your mobile device, search for the
camcorder ID “hp_f650x_123456” from the list (last 6 numbers are
system random numbers). Enter default password 12345678.
4. There is a Wi-Fi icon on the camcorder’s screen. Once the icon is
blue, your connection has been successfully established.
Note:
1. The mobile device shall be within a maximum of a 5m distance from the camcorder without any
buildings in between.
2. When the Wi-Fi function of the camcorder is ON but not yet connecting with your mobile device, or
the connection is disconnected, the Wi-Fi icon on camcorder’s screen will be white, and you will
need to re-activate the Wi-Fi and re-pair with your mobile device.
3. After connecting the mobile device with the camcorder, and activate app feature “Camera
Preview”, all the button operation of the camcorder will be disable; all the operations shall be
carried out via the Go Dashcam App.
4. The language of the Go Dashcam App will be consistent with your mobile device, beyond the
language options, the App will be activated with default language.
35
5 Using the Go Dashcam application
Touch [Go Dashcam]
icon to activate the application. The
main screen will pop up. Follow the below instruction to operate
this application.
36
5.1 Camera preview, record, snapshot
You can use this feature to preview, record or take snapshot.
1. The mobile device will display camcorder’s preview screen. The
camcorder will lose control and screen will show ”Network Streaming”.
Please use Go Dashcam app to operate the camcorder.
icon
Description
1
2
Start/stop recording.
Snapshot.
3
Not available for this model.
37
5.2 Playback, delete, download
You can use this feature to playback or delete the file saved in camcorder,
or to download the file from camcorder to your mobile device.
1. Touch the icon
playback].
[Video playback] or
[Picture
2. The files saved in the camcorder will be displayed on your mobile
device. Camcorder will stop recording for a few seconds until your
mobile device finishes reading the saved files from camcorder, and
screen will show ”Network Playback”.
3. Touch the preview image of video or picture to playback.
4. Touch the right top corner “Select” and pick up the files that you
want to delete or download, and touch below icon to execute.
38
Icon
Description
1
Not available for this model.
Download the file from camcorder to your mobile
device
2
3
Delete
Exit
4
Note:
1. If you find the video playback without audio, please check if you turn on Voice Record on the menu.
If you do turn it on, it means the mobile device itself doesn’t support the video decoding. It’s not the
problem of the file. We recommend you to install a free app software such as VLC to playback the
file.
2. Deleted files cannot be recovered. Ensure the files have been backed-up before deletion.
3. Picture and video files could be downloaded to the internal memory of your mobile device. Use the
application program in your mobile device to view the file.
4. The downloaded videos or pictures will be saved in the album of your mobile device, at the mean
time it will create a new folder “Go Dashcam”. You can preview the files from the album.
39
5.3 Local album
You can use this feature to playback or delete the file that you download
to your mobile device.
1. Touch icon
[Local Album]。
2. Pick up the file that you want to playback.
3. The downloaded videos or pictures will be saved in the album of your
mobile device, at the mean time it will create a new folder “Go
Dashcam”. You can preview or delete the files from the album.
Note:
1. Deleted files cannot be recovered. Ensure the files have been backed-up before deletion.
2. If you find the downloaded files could not be played or without audio, which means the mobile
device itself does not support the video decoding. It’s not the problem of the file. We recommend
you to install a free App software such as VLC to playback the file.
40
5.4 Camera Setting
You can use this feature to set up your car camcorder.
1. Touch icon
[Camera Setting].
2. Refer to the below table for details of menu items and available
menu options.
Menu option
Description
Available option
1080p 30fps HDR
Set the desired video
resolution.
Resolution
720p 30fps HDR
Save respective video files
in a length of the selected
duration.
Record Interval
Voice Record
30 sec / 1 min / 3 min
Setting for activating audio
in the video.
On / Off
On / Off
If the time stamp is
enabled, recording files or
photos will show the date
and time.
Time Stamp
Return to factory default
setting.
Default
Format
Yes / No
Yes / No
To format the memory
card, all the files in the
camcorder will be deleted.
WiFi Setting
To set up Wi-Fi password
Indicates the current car
Firmware Version camcorder’s firmware
version.
Indicates the current
App Version
application version.
41
6 Adjusting the Settings
6.1 Using the Menu
You can customize the general settings via the on-screen display (OSD)
menus.
1. Press the
2. Press the
the
3. Press the
press the
button to enter the OSD menu.
/
button to select menu item, and then press
button for entering function menu.
button to select or adjust the value, and then
/
button to confirm setting.
4. Press the
button to return recording screen.
6.2 Menu Items
Refer to the below table for details of main menu and function list.
Menu option
Description
Available option
Video
Emergency
Picture
Select the file category that
you want to view.
Playback
Set up Wi-Fi linkage of a
mobile phone.
Wi-Fi
On / Off
Displays the current state of
the satellite reception.
Satellite Status
If the satellite time is enabled,
the car camcorder clock will
synchronize according to the
satellite time zone you set.
When you turn on this
feature, it will display the
satellite time preferentially,
and cannot be manually
changed.
Satellite
Synchronization
On / Off
The system displays the
speed setting unit.
Speed Unit
KM/H / MPH
42
Menu option
Description
Available option
If the Speed Cam Alert
function is enabled, once your
car’s location is determined
by GPS and approaches a
speed cam, this product
produces audible alert and
screen message.
Speed Cam Alert
On / Off
Add Speed Point: The
satellite positioning will
manually add speed camera
location. You can add up to 50
speed camera locations to the Add Speed Point / Delete
Speed Position
Management
built-in system.
Last Position / Delete All
Position
Delete Last Position: Delete
the last speed camera point.
Delete All Position:
Delete all speed camera
point.
Set a customized maximum
speed limit. When the vehicle
speed exceeds the maximum,
an audible alert is
automatically triggered and a
warning message is displayed
on the screen.
Press the
/
button to
set the speed limit. You can
set the off, or set speed limit
from 50 to 200km/h (30 to
125mph)
Speed Limit Alert
Press the
/
button to
set the satellite time. You
may customize it between
GMT -12:00 ~ GMT +14:00
Set Time Zone
Date / Time
Set the time zone you are in.
Press the
adjust the value, and then
press the button to
/
button to
Set the date and time.
Language setting.
set the next field, and
complete setting
According to the actual
shipping regions.
Language
If the time stamp is enabled,
recording files or photos will
show the date and time.
Time Stamp
On / Off
1920x1080 30fps HDR
1280x720 30fps HDR
Resolution
Setting of video resolution.
43
Menu option
Description
Available option
Press the
/
button to
EV
Setting of exposure value.
set the exposure value. It can
be set between -2 ~ +2
Set LCD off time. Camcorder
screen will be off after a set
time if no operation is
detected during the standby
or record mode. Press any
button will switch it on.
(Recording is not affected
when screen is off).
On/ Turn off after 7 sec /
Turn off after 1min/ Turn off
after 3min
LCD Setting
Setting for activating audio in
the video.
Enable / disable power-on
sound and key tone.
Voice Record
Key Tone
On / Off
On / Off
Press the
set the volume. It can be set
between 0 ~ 10.
/
button to
Volume
Adjust the sound volume.
Save respective video files in
a length of the selected
duration.
Record Interval
30 sec. / 1 min. / 3 min.
If one of parking mode is
activated, the camcorder will
enter parking mode 10
seconds after disconnect the
external power.
Off/ Park Recording / Motion
and Collision Detection /
Timelapse
Parking Mode
If Collision Detection is
High Sensitivity / Normal
Sensitivity / Low Sensitivity /
Off
activated, this camcorder
starts emergency recording
once it detects any collision.
Collision Detection
When Driver Fatigue Alert is
enabled, audible alert and
screen message will be
activated 1 hour after the
camcorder is powered on,
with a repetition every 30
minutes.
Driver Fatigue Alert
On / Off
44
Menu option
Description
Available option
When Headlight Warning is
activated, camcorder will
issue an audible alert and
screen message reminding
that insufficient brightness is
sensed on the recording face.
Headlight Warning
On / Off
Once your car’s location is
determined by GPS and the
LDWS function is enabled, this
camcorder produces audible
alert and screen message
when you drive off of or
change lanes at speeds over
70 km/h (43 mph).
LDWS
FCWS
On / Off
When FCWS is activated after
satellite positioning,
camcorder will issue audible
alert and screen message
when vehicle speed is above
60 km/h (37 mph) and the
distance with the front vehicle
is less than 20m.
On / Off
If FCMD function is enabled,
when the front car moves and
you don’t start to drive
forward, the camcorder will
issue audible alert and screen
message.
FCMD
On / Off
Video
File Deletion
Anti-flicker
Delete the file(s).
Emergency
Picture
Domestic power supply varies
by area. It is recommended
that you should check the
“Table of voltage and
frequency of different
countries” for the correct
setting.
60Hz / 50Hz
45
Menu option
Description
Available option
Format the memory card
inserted in the equipment. All
the files in the card will be
erased.
Format
Yes / No
The system reverts to the
default setting.
Default
Yes / No
Indicates the current
firmware version.
Firmware Version
46
7 Installing the Software
1. Place the attached CD ROM into the CD player.
2. If the CD does not execute automatically, please use Windows File
Manager to execute the Install_CD.exe file in the CD.
The following screen will be shown up.
3. Press the [Menu] item to start the installation process according to
the instructions on-screen.
47
8 SuperCar
7
8
9
10
11
1
12
13
14
15
2
3
4
5
16
6
No.
Item
Video Player
No.
Item
1
2
3
4
5
9
File Path
Play / Pause
Previous
Next
10
11
12
13
Browser File
File List
File Name
Volume
Stop
Playback Duration / Total
Duration
6
Electronic Map
14
7
8
Compass
15
16
Signal Noise Ratio (SNR)
G-Sensor
Speed Meter
Note:
1. To display the route on Electronic Map, please make sure the internet is connected before starting
the video playback.
2. Video files of front-view camera (MOV) and GPS/G-Sensor files (NMEA) must be stored in the same
folder before starting the playback.
3. The SuperCar software is only applicable to Windows operating system. For Mac users, please
search “SuperCar”
App in built-in Mac App Store.
48
9
Specifications
Item
Description
Image sensor
Effective pixels
Storage media
LCD display
1/2.7” CMOS sensor
1920 (H) x 1080 (V)
Supports Micro SDHC, up to 32GB class 10 speed or greater
2” LCD color TFT
Wide Angle Fixed Focus lens
Aperture: Up to F2.2
Lens
Focus range
1.5m~Infinity
Satellite System GPS
、
Resolution: 1080P/ 30 fps 720P/ 30 fps
Video
Format: MOV
Resolution: depends on video resolution setting
Still image
(Photograph)
Format: DCF (JPG)
Electronic shutter
3-Axis G-Force sensor
Auto
Shutter
G-Sensor
ISO
White Balance
Microphone
Speaker
Auto
Built-in
Built-in
Interface
Mini USB
Power
Super Capacitor
49
Item
Description
Operating
Temperature
0° ~ 45° C
Operating Humidity 20 ~ 70% RH
Storage
-20° ~ 70° C
Temperature
Dimensions
Weight
58 x 43.5 x 45.3 mm
Approx. 82g
Built-in IEEE 802.11b/g/n(HT20) Wi-Fi chip: RTL8188FTV
Frequency range
Wi-Fi Channel
2412~2472MHz
Ch1~Ch13
18dBm
Wi-Fi Max. output
50
|
