Hardware Reference Guide
HP EliteDesk 705 G3 SFF Business PC
About This Book
This guide provides basic information for upgrading the HP EliteDesk Business PC.
WARNING! Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information considered important but not hazard-related (for example, messages
related to property damage). A notice alerts the user that failure to follow a procedure exactly as described
could result in loss of data or in damage to hardware or software. Also contains essential information to
explain a concept or to complete a task.
NOTE: Contains additional information to emphasize or supplement important points of the main text.
TIP: Provides helpful hints for completing a task.
iii
iv
About This Book
Table of contents
1 Product features ........................................................................................................................................... 1
Standard configuration features ........................................................................................................................... 1
Front panel components ....................................................................................................................................... 2
Serial number location .......................................................................................................................................... 4
2 Hardware upgrades ....................................................................................................................................... 5
Warnings and cautions .......................................................................................................................................... 5
Replacing the computer access panel ................................................................................................................... 7
Removing the front bezel ...................................................................................................................................... 8
Replacing the front bezel .................................................................................................................................... 10
Cleaning the optional dust filter .......................................................................................................................... 10
Changing from desktop to tower configuration .................................................................................................. 13
System board connections .................................................................................................................................. 14
Installing additional memory .............................................................................................................................. 15
DIMMs ................................................................................................................................................ 15
Populating DIMM sockets .................................................................................................................. 15
Installing DIMMs ................................................................................................................................ 16
Removing or installing an expansion card .......................................................................................................... 18
Drive positions ..................................................................................................................................................... 22
Removing and installing drives ........................................................................................................................... 23
Removing and replacing a primary 3.5-inch hard drive ................................................................... 27
Removing a secondary 3.5-inch hard drive ...................................................................................... 30
Installing a secondary 3.5-inch hard drive ....................................................................................... 32
Removing a 2.5-inch hard drive ........................................................................................................ 35
Installing a 2.5-inch hard drive ......................................................................................................... 37
Padlock .............................................................................................................................................. 40
HP Business PC Security Lock V2 ...................................................................................................... 41
v
Appendix A Battery replacement ..................................................................................................................... 47
Appendix B Electrostatic discharge .................................................................................................................. 50
Preventing electrostatic damage ........................................................................................................................ 50
Grounding methods ............................................................................................................................................. 50
Appendix C Computer operating guidelines, routine care and shipping preparation ............................................. 51
Computer operating guidelines and routine care ............................................................................................... 51
Cleaning ............................................................................................................................................. 52
Safety ................................................................................................................................................ 52
Shipping preparation ........................................................................................................................................... 52
Appendix D Accessibility ................................................................................................................................. 53
Supported assistive technologies ....................................................................................................................... 53
Contacting support .............................................................................................................................................. 53
Index ............................................................................................................................................................. 54
vi
1 Product features
Standard configuration features
Features may vary depending on the model. For support assistance and to learn more about the hardware
and software installed on your computer model, run the HP Support Assistant utility.
NOTE: This computer model can be used in a tower orientation or a desktop orientation.
Standard configuration features
1
Front panel components
Drive configuration may vary by model. Some models have a bezel blank covering the slim optical drive bay.
Front panel components
1
2
3
4
5
Slim optical drive (optional)
USB 2.0 charging (powered) port (black)
USB 2.0 port (black)
6
7
8
9
Audio-out (headphone) jack
Power button
Hard drive activity light
SD card reader (optional)
USB 3.0 ports (blue)
Audio-out (headphone)/Audio-in (microphone) combo
jack
NOTE: When a device is plugged into the Audio-out (headphone)/Audio-in (microphone) combo jack, a dialog box will pop
up asking if you want to use the jack for a microphone or a headphone. You can reconfigure the jack at any time by double-
clicking the Audio Manager icon in the Windows® taskbar.
NOTE: The USB 2.0 charging port also provides current to charge a device such as a smart phone. The charging current is
available whenever the power cord is plugged into the system, even when the system is off.
NOTE: The Power On light is normally white when the power is on. If it is flashing red, there is a problem with the
computer and it is displaying a diagnostic code. Refer to the Maintenance and Service Guide to interpret the code.
2
Chapter 1 Product features
Rear panel components
Rear panel components
1
PS/2 mouse connector (green)
7
PS/2 keyboard connector (purple)
2
3
Serial port
8
9
DisplayPort monitor connectors
VGA monitor connector
RJ-45 (network) jack
4
USB 2.0 ports (black) with keyboard wakeup
function
10
USB 3.1 ports (blue)
USB 3.1 ports (blue)
5
6
Audio-in jack (blue)
11
12
Power cord connector
Audio-out jack for powered audio devices
(green)
NOTE: An optional second serial port and an optional parallel port are available from HP.
If using a USB keyboard, HP recommends connecting the keyboard to one of the USB 2.0 ports with the wakeup feature. The
wakeup feature is also supported on the PS/2 connector if enabled in BIOS F10 Setup.
When a device is plugged into the microphone/headphone jack, a dialog box will pop up asking if you want to use the jack for a
microphone or a headphone. You can reconfigure the jack at any time by double-clicking the Audio Manager icon in the
Windows taskbar.
When a graphics card is installed in one of the system board slots, the video connectors on the graphics card and/or the
integrated graphics on the system board may be used. The specific graphics card installed and software configuration will
determine the behavior.
The system board graphics can be disabled by changing settings in BIOS F10 Setup.
Rear panel components
3
2 Hardware upgrades
Serviceability features
The computer includes features that make it easy to upgrade and service. A Torx T15 or flat-bladed
screwdriver is needed for some of the installation procedures described in this chapter.
Warnings and cautions
Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and
warnings in this guide.
WARNING! To reduce the risk of personal injury from electrical shock, hot surfaces, or fire:
Disconnect the power cord from the AC outlet and allow the internal system components to cool before
touching.
Do not plug telecommunications or telephone connectors into the network interface controller (NIC)
receptacles.
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup,
posture, and health and work habits for computer users, and provides important electrical and mechanical
WARNING! Energized and moving parts inside.
Disconnect power to the equipment before removing the enclosure.
Replace and secure the enclosure before re-energizing the equipment.
IMPORTANT: Static electricity can damage the electrical components of the computer or optional
equipment. Before beginning these procedures, ensure that you are discharged of static electricity by briefly
When the computer is plugged into an AC power source, voltage is always applied to the system board. You
must disconnect the power cord from the power source before opening the computer to prevent damage to
internal components.
Serviceability features
5
Removing the computer access panel
To access internal components, you must remove the access panel.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand and lay the computer down.
6. Pull up the access panel handle (1), and then lift the panel off the computer (2).
6
Chapter 2 Hardware upgrades
Removing the front bezel
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand and lay the computer down.
6. Remove the computer access panel.
7. Lift up the three tabs on the side of the bezel (1), and then rotate the bezel off the chassis (2).
8
Chapter 2 Hardware upgrades
Removing a slim optical drive bezel blank
On some models, there is a bezel blank covering the slim optical drive bay. Remove the bezel blank before
installing an optical drive. To remove the bezel blank:
1. Remove the computer access panel and front bezel.
2. To remove the bezel blank, press inward on the three retaining tabs that hold the bezel blank in place
(1), and then rotate the bezel blank off the front bezel (2).
Removing a slim optical drive bezel blank
9
Replacing the front bezel
Insert the four hooks on the bottom side of the bezel into the rectangular holes on the chassis (1), and then
rotate the top side of the bezel onto the chassis (2) and snap it in place.
Cleaning the optional dust filter
Some models are equipped with a front bezel that includes a dust filter. You must periodically clean the dust
filter so that the dust collected on the filter does not impede air flow through the computer.
NOTE: The optional dust filter front bezel is available from HP.
To clean the dust filter:
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
NOTE: Regardless of the power-on state, voltage is always present on the system board as long as the
system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the
internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel and front bezel.
10 Chapter 2 Hardware upgrades
7. To remove the dust filter access panel, press the right side of the filter access panel on the main bezel
(1), rotate the right side of the filter access panel off the main bezel (2), and then pull the left side of the
filter access panel out of the main bezel (3).
8. To remove the dust filter, lift the two separated ends of the filter (1), and then pull the filter off the filter
access panel (2).
9. Clean dust from the filter access panel with a soft brush or cloth. If heavily soiled, rinse the filter access
panel clean with water.
10. Clean the filter element with a soft brush or cloth. If heavily soiled, rinse the filter clean with water.
Cleaning the optional dust filter 11
11. To replace the dust filter, slide the right side of the filter onto the filter access panel (1), and then press
the filter onto the filter access panel (2) to secure it in place.
12. To replace the filter access panel, slide the left side of the filter access panel onto the main bezel (1), and
then press the right side of the filter access panel onto the main bezel (2) to secure it in place.
13. Replace the front bezel and computer access panel.
14. If the computer was on a stand, replace the stand.
15. Reconnect the power cord and any external devices, and then turn on the computer.
16. Lock any security devices that were disengaged when the access panel was removed.
12 Chapter 2 Hardware upgrades
Changing from desktop to tower configuration
The Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be
purchased from HP.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. Orient the computer so that its right side is facing down and place the computer in the optional stand.
NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower
stand.
6. Reconnect the power cord and any external devices, and then turn on the computer.
NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains clear
and free of obstructions.
7. Lock any security devices that were disengaged when the access panel was removed.
Changing from desktop to tower configuration 13
System board connections
Refer to the following illustration and table to identify the system board connectors for your model.
Item System board connector
System board label
Color
Component
1
PCI Express x16 Gen 2
downshifted to a x4
X4PCIEXP
white
Expansion card
2
3
4
5
PCI Express x1 Gen 2
PCI Express x16 Gen 3
PCI Express x1 Gen 2
SATA 3.0
X1PCIEXP2
X16PCIEXP
X1PCIEXP1
SATA2
black
Expansion card
Expansion card
Expansion card
black
black
light blue
Any SATA device other than the primary
hard drive
6
DIMM4 (Channel A)
DIMM3 (Channel A)
DIMM2 (Channel B)
DIMM1 (Channel B)
SATA 3.0
DIMM4
DIMM3
DIMM2
DIMM1
SATA0
SATA1
white
Memory module
Memory module
Memory module
Memory module
Primary hard drive
7
black
8
white
9
black
10
11
dark blue
light blue
SATA 3.0
Any SATA device other than the primary
hard drive
12
13
Battery
BAT
black
black
Battery
Serial port
COMB
Optional second serial port
14 Chapter 2 Hardware upgrades
Installing additional memory
The computer comes with double data rate 4 synchronous dynamic random access memory (DDR4-SDRAM)
dual inline memory modules (DIMMs).
DIMMs
The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These
memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory
support, you can populate the system board with up to 64 GB of memory configured in a high-performing
dual channel mode.
DDR4-SDRAM DIMMs
For proper system operation, the DIMMs must be:
●
●
●
industry-standard 288-pin
unbuffered non-ECC PC4-17000 DDR4-2133 MHz-compliant
1.2 volt DDR4-SDRAM DIMMs
The DIMMs must also:
●
●
support CAS latency 15 DDR4 2133 MHz (15-15-15 timing)
contain the mandatory JEDEC SPD information
In addition, the computer supports:
●
●
●
512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies
single-sided and double-sided DIMMs
DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not supported
NOTE: The system will not operate properly if you install unsupported DIMMs.
Populating DIMM sockets
There are four DIMM sockets on the system board, with two sockets per channel. The sockets are labeled
DIMM1, DIMM2, DIMM3, and DIMM4. Sockets DIMM1 and DIMM2 operate in memory channel B. Sockets DIMM3
and DIMM4 operate in memory channel A.
The system will automatically operate in single channel mode, dual channel mode, or flex mode, depending
on how the DIMMs are installed.
NOTE: Single channel and unbalanced dual channel memory configurations will result in inferior graphics
performance.
●
●
The system will operate in single channel mode if the DIMM sockets are populated in one channel only.
The system will operate in a higher-performing dual channel mode if the total memory capacity of the
DIMMs in Channel A is equal to the total memory capacity of the DIMMs in Channel B. The technology and
device width can vary between the channels. For example, if Channel A is populated with two 1 GB
DIMMs and Channel B is populated with one 2 GB DIMM, the system will operate in dual channel mode.
●
The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is not equal
to the total memory capacity of the DIMMs in Channel B. In flex mode, the channel populated with the
least amount of memory describes the total amount of memory assigned to dual channel and the
remainder is assigned to single channel. For optimal speed, the channels should be balanced so that the
Installing additional memory 15
largest amount of memory is spread between the two channels. If one channel will have more memory
than the other, the larger amount should be assigned to Channel A. For example, if you are populating
the sockets with one 2 GB DIMM, and three 1 GB DIMMs, Channel A should be populated with the 2 GB
DIMM and one 1 GB DIMM, and Channel B should be populated with the other two 1 GB DIMMs. With this
configuration, 4 GB will run as dual channel and 1 GB will run as single channel.
●
In any mode, the maximum operational speed is determined by the slowest DIMM in the system.
Installing DIMMs
IMPORTANT: You must disconnect the power cord and wait approximately 30 seconds for the power to drain
before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to
the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing
memory modules while voltage is present may cause irreparable damage to the memory modules or system
board.
The memory module sockets have gold-plated metal contacts. When upgrading the memory, it is important
to use memory modules with gold-plated metal contacts to prevent corrosion and/or oxidation resulting from
having incompatible metals in contact with each other.
Static electricity can damage the electronic components of the computer or optional cards. Before beginning
these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal
When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the
module.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: You must disconnect the power cord and wait approximately 30 seconds for the power to
drain before adding or removing memory modules. Regardless of the power-on state, voltage is always
supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or
removing memory modules while voltage is present may cause irreparable damage to the memory
modules or system board.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components
to cool before touching.
16 Chapter 2 Hardware upgrades
7. Open both latches of the memory module socket (1), and insert the memory module into the socket (2).
NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab
on the memory socket.
Populate the black DIMM sockets before the white DIMM sockets.
For maximum performance, populate the sockets so that the memory capacity is spread as equally as
information.
8. Push the module down into the socket, ensuring that the module is fully inserted and properly seated.
Make sure the latches are in the closed position (3).
9. Repeat steps 7 and 8 to install any additional modules.
10. Replace the computer access panel.
11. If the computer was on a stand, replace the stand.
12. Reconnect the power cord and any external devices, and then turn on the computer.
13. Lock any security devices that were disengaged when the access panel was removed.
The computer should automatically recognize the additional memory the next time you turn on the computer.
Installing additional memory 17
Removing or installing an expansion card
The computer has two PCI Express x1 expansion sockets, one PCI Express x16 expansion socket, and one PCI
Express x16 expansion socket that is downshifted to a x4 socket.
NOTE: The PCI Express sockets support only low profile cards.
You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 socket.
For dual graphics card configurations, the first (primary) card must be installed in the PCI Express x16 socket
that is NOT downshifted to a x4.
To remove, replace, or add an expansion card:
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Locate the correct vacant expansion socket on the system board and the corresponding expansion slot
on the back of the computer chassis.
8. Release the slot cover retention latch that secures the slot covers by lifting the tab on the latch and
rotating the latch to the open position.
9. Before installing an expansion card, remove the expansion slot cover or the existing expansion card.
NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to
the expansion card.
18 Chapter 2 Hardware upgrades
a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot
cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the
chassis.
b. If you are removing a PCI Express x1 card, hold the card at each end and carefully rock it back and
forth until the connectors pull free from the socket. Lift the card straight up (1) then away from the
inside of the chassis (2) to remove it. Be sure not to scrape the card against other components.
Removing or installing an expansion card 19
c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion
socket away from the card and carefully rock the card back and forth until the connectors pull free
from the socket. Lift the card straight up then away from the inside of the chassis to remove it. Be
sure not to scrape the card against other components.
10. Store the removed card in anti-static packaging.
11. If you are not installing a new expansion card, install an expansion slot cover to close the open slot.
IMPORTANT: After removing an expansion card, you must replace it with a new card or expansion slot
cover for proper cooling of internal components during operation.
12. To install a new expansion card, hold the card just above the expansion socket on the system board then
move the card toward the rear of the chassis (1) so that the bottom of the bracket on the card slides into
the small slot on the chassis. Press the card straight down into the expansion socket on the system
board (2).
NOTE: When installing an expansion card, press firmly on the card so that the whole connector seats
properly in the expansion card socket.
20 Chapter 2 Hardware upgrades
13. Rotate the slot cover retention latch back in place to secure the expansion card.
14. Connect external cables to the installed card, if needed. Connect internal cables to the system board, if
needed.
15. Replace the computer access panel.
16. If the computer was on a stand, replace the stand.
17. Reconnect the power cord and any external devices, and then turn on the computer.
18. Lock any security devices that were disengaged when the access panel was removed.
19. Reconfigure the computer, if necessary.
Removing or installing an expansion card 21
Removing and installing drives
When installing drives, follow these guidelines:
●
●
●
The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on
the system board labeled SATA0.
Connect secondary hard drives and optical drives to one of the light blue SATA connectors on the system
board (labeled SATA1 and SATA2).
HP has provided four extra 6-32 hard drive mounting screws installed on the top of the hard drive cage
(1) for installing a hard drive into the 3.5-inch secondary hard drive bay. If you are replacing a hard drive,
remove the mounting screws from the old drive and install them in the new drive.
security on page 46 for more information).
IMPORTANT: To prevent loss of work and damage to the computer or drive:
If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and
unplug the power cord. Do not remove a drive while the computer is on or in standby mode.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector. For more information about preventing electrostatic damage, refer to Electrostatic
Handle a drive carefully; do not drop it.
Do not use excessive force when inserting a drive.
Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields such as
monitors or speakers.
If a drive must be mailed, place the drive in a bubble-pack mailer or other protective packaging and label the
package “Fragile: Handle With Care.”
Removing and installing drives 23
Removing a 9.5 mm slim optical drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Disconnect the power cable (1) and data cable (2) from the rear of the optical drive, push the green
release latch on the right rear side of the drive toward the center of the drive (3), and then slide the drive
forward and out of the bay through the front bezel (4).
IMPORTANT: When removing the cables, pull the tab or connector instead of the cable itself to avoid
damaging the cable.
24 Chapter 2 Hardware upgrades
Installing a 9.5 mm slim optical drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. If you are installing a slim optical drive in a bay covered by a bezel blank, remove the front bezel and
information.
8. Align the small pin on the release latch with the small hole on the side of the drive and press the latch
firmly onto the drive.
Removing and installing drives 25
9. Slide the optical drive through the front of the chassis (1) all the way into the bay so that it locks in
place, and then connect the power cable (2) and data cable (3) to the rear of the drive.
10. Connect the opposite end of the data cable to one of the light blue SATA connectors on the system board
(labeled SATA1 or SATA2) if not already connected.
connectors.
11. Replace the front bezel if it was removed.
12. Replace the computer access panel.
13. If the computer was on a stand, replace the stand.
14. Reconnect the power cord and any external devices, and then turn on the computer.
15. Lock any security devices that were disengaged when the access panel was removed.
26 Chapter 2 Hardware upgrades
Removing and replacing a primary 3.5-inch hard drive
NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you
can transfer the data to the new hard drive.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive.
Removing and installing drives 27
8. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out,
slide the drive back until it stops, and then lift the drive up and out of the bay (2).
9. To install a hard drive, you must transfer the mounting screws from the old hard drive to the new hard
drive.
28 Chapter 2 Hardware upgrades
10. Align the mounting screws with the slots on the chassis drive cage, press the hard drive down into the
bay, and then slide it forward until it stops and locks in place.
11. Connect the power cable (1) and data cable (2) to the rear of the hard drive.
NOTE: The data cable for the primary hard drive must be connected to the dark blue connector on the
system board labeled SATA0 to avoid any hard drive performance problems.
12. Replace the computer access panel.
13. If the computer was on a stand, replace the stand.
14. Reconnect the power cord and any external devices, and then turn on the computer.
15. Lock any security devices that were disengaged when the access panel was removed.
Removing and installing drives 29
Removing a secondary 3.5-inch hard drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Rotate the drive cage to its upright position.
30 Chapter 2 Hardware upgrades
8. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive. Press the latch on the
side of the drive cage (3), and then slide the drive out of the drive bay (4).
9. If you are installing a new drive, refer to Installing a secondary 3.5-inch hard drive on page 32. If you
are not installing a new drive, rotate the drive cage down and replace the access panel.
Removing and installing drives 31
Installing a secondary 3.5-inch hard drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Install four silver 6-32 mounting screws on the sides of the drive (two on each side).
NOTE: HP has supplied four extra silver 6-32 mounting screws installed on the chassis next to the
primary 3.5-inch hard drive bay. Refer to Removing and installing drives on page 23 for an illustration of
the location of the extra mounting screws.
When replacing a drive, transfer the four mounting screws from the old drive to the new drive.
32 Chapter 2 Hardware upgrades
8. Rotate the drive cage to its upright position.
9. Slide the drive into the drive bay (1), and then connect the power cable (2) and data cable (3) to the rear
of the hard drive.
NOTE: If the drive is a secondary hard drive, connect the other end of data cable to one of the light
blue SATA connectors on the system board. If the drive is the primary hard drive, connect the other end
of the data cable to the dark blue SATA connector on the system board.
Removing and installing drives 33
10. Rotate the drive cage back down to its normal position.
CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.
11. Replace the computer access panel.
12. If the computer was on a stand, replace the stand.
13. Reconnect the power cord and any external devices, and then turn on the computer.
14. Lock any security devices that were disengaged when the access panel was removed.
34 Chapter 2 Hardware upgrades
Removing a 2.5-inch hard drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Rotate the drive cage to its upright position.
Removing and installing drives 35
8. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive.
9. Pull the release lever at the rear of the drive outward (1). Then slide the drive back until it stops and pull
it down and out of the drive bay (2).
10. If you are installing a new drive, refer to Installing a 2.5-inch hard drive on page 37. If you are not
installing a new drive, rotate the drive cage down and replace the access panel.
36 Chapter 2 Hardware upgrades
Installing a 2.5-inch hard drive
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as long as
the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to
the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. Install four black and blue M3 mounting screws (two on each side of the drive).
NOTE: M3 metric mounting screws can be purchased from HP.
When replacing a drive, transfer the four mounting screws from the old drive to the new drive.
8. Rotate the drive cage to its upright position.
Removing and installing drives 37
9. Align the mounting screws on the drive with the J-slots on the sides of the drive bay. Press the drive into
the drive bay, and then slide the drive forward until it locks in place.
10. Connect the power cable (1) and data cable (2) to the rear of the hard drive.
NOTE: If the 2.5-inch hard drive is the primary drive, connect the other end of the data cable to the
dark blue SATA connector on the system board labeled SATA0 . If it is a secondary hard drive, connect the
other end of the data cable to one of the light blue SATA connectors on the system board.
38 Chapter 2 Hardware upgrades
11. Rotate the drive cage back down to its normal position.
IMPORTANT: Be careful not to pinch any cables or wires when rotating the drive cage down.
12. Replace the computer access panel.
13. If the computer was on a stand, replace the stand.
14. Reconnect the power cord and any external devices, and then turn on the computer.
15. Lock any security devices that were disengaged when the access panel was removed.
Removing and installing drives 39
HP Business PC Security Lock V2
1. Attach the security cable fastener to a desktop using the appropriate screws for your environment
(screws not provided) (1), and then snap the cover onto the base of the cable fastener (2).
2. Loop the security cable around a stationary object.
Installing a security lock 41
3. Slide the security cable through the security cable fastener.
4. Pull the two scissor hands of the monitor lock apart and insert the lock into the security slot on the rear
of the monitor (1), close the scissor hands together to secure the lock in place (2), and then slide the
cable guide through the center of the monitor lock (3).
42 Chapter 2 Hardware upgrades
5. Slide the security cable through the security guide installed on the monitor.
6. Attach the accessory cable fastener to a desktop using the appropriate screw for your environment
(screw not provided) (1), and then place the accessory cables into the base of the fastener (2).
Installing a security lock 43
7. Slide the security cable through the holes in the accessory cable fastener.
8. Screw the lock to the chassis using the screw provided (1). Insert the plug end of the security cable into
the lock (2) and push the button in (3) to engage the lock. Use the key provided to disengage the lock.
44 Chapter 2 Hardware upgrades
9. When you have completed all steps, all of the devices at your workstation will be secured.
Installing a security lock 45
Front bezel security
The front bezel can be secured in place by installing a 6-32 screw through the center tab on the bezel into the
chassis.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the computer access panel.
7. If you do not have a 6-32 standard screw, remove one of the four silver 6-32 standard screws located on
top of the drive cage. Refer to Removing and installing drives on page 23 for an illustration of the 6-32
standard screw locations.
8. Install the 6-32 security screw through the middle front bezel release tab to secure the front bezel in
place.
9. Replace the computer access panel.
10. If the computer was on a stand, replace the stand.
11. Reconnect the power cord and any external devices, and then turn on the computer.
12. Lock any security devices that were disengaged when the access panel was removed.
46 Chapter 2 Hardware upgrades
A Battery replacement
The battery that comes with the computer provides power to the real-time clock. When replacing the battery,
use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt
lithium coin cell battery.
WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of fire and
burns if the battery is not handled properly. To reduce the risk of personal injury:
Do not attempt to recharge the battery.
Do not expose to temperatures higher than 60°C (140°F).
Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Replace the battery only with the HP spare designated for this product.
IMPORTANT: Before replacing the battery, it is important to back up the computer CMOS settings. When the
battery is removed or replaced, the CMOS settings will be cleared.
Static electricity can damage the electronic components of the computer or optional equipment. Before
beginning these procedures, ensure that you are discharged of static electricity by briefly touching a
grounded metal object.
NOTE: The lifetime of the lithium battery can be extended by plugging the computer into a live AC outlet.
The lithium battery is only used when the computer is NOT connected to AC power.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, and turn off any external devices.
4. Disconnect the power cord from the AC outlet and disconnect any external devices.
IMPORTANT: Regardless of the power-on state, voltage is always present on the system board as long
as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage
to the internal components of the computer.
5. Remove the computer access panel.
6. Locate the battery and battery holder on the system board.
NOTE: On some computer models, it may be necessary to remove an internal component to gain
access to the battery.
7. Depending on the type of battery holder on the system board, complete the following instructions to
replace the battery.
Type 1
a. Lift the battery out of its holder.
47
b. Slide the replacement battery into position, positive side up. The battery holder automatically
secures the battery in the proper position.
Type 2
a. To release the battery from its holder, squeeze the metal clamp that extends above one edge of
the battery. When the battery pops up, lift it out (1).
b. To insert the new battery, slide one edge of the replacement battery under the holder’s lip with the
positive side up. Push the other edge down until the clamp snaps over the other edge of the
battery (2).
Type 3
a. Pull back the clip (1) that is holding the battery in place, and remove the battery (2).
48 Appendix A Battery replacement
b. Insert the new battery and position the clip back into place.
NOTE: After the battery has been replaced, use the following steps to complete this procedure.
8. Replace the computer access panel.
9. Reconnect the power cord and any external devices, and then turn on the computer.
10. Reset the date and time, your passwords, and any special system setups using Computer Setup.
11. Lock any security devices that were disengaged when the computer access panel was removed.
49
B Electrostatic discharge
A discharge of static electricity from a finger or other conductor may damage system boards or other static-
sensitive devices. This type of damage may reduce the life expectancy of the device.
Preventing electrostatic damage
To prevent electrostatic damage, observe the following precautions:
●
●
●
●
●
Avoid hand contact by transporting and storing products in static-safe containers.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
Place parts on a grounded surface before removing them from their containers.
Avoid touching pins, leads, or circuitry.
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods
There are several methods for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
●
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm +/- 10 percent resistance in the ground cords. To
provide proper ground, wear the strap snug against the skin.
●
Use heelstraps, toestraps, or bootstraps at standing workstations. Wear the straps on both feet when
standing on conductive floors or dissipating floor mats.
●
●
Use conductive field service tools.
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer,
reseller, or service provider.
NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service
provider.
50 Appendix B Electrostatic discharge
C Computer operating guidelines, routine
care and shipping preparation
Computer operating guidelines and routine care
Follow these guidelines to properly set up and care for the computer and monitor:
●
●
Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold.
Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides
of the computer and above the monitor to permit the required airflow.
●
Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the
keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also
restricts airflow.
●
●
Never operate the computer with the access panel or any of the expansion card slot covers removed.
Do not stack computers on top of each other or place computers so near each other that they are subject
to each other’s re-circulated or preheated air.
●
If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be
provided on the enclosure, and the same operating guidelines listed above will still apply.
●
●
●
Keep liquids away from the computer and keyboard.
Never cover the ventilation slots on the monitor with any type of material.
Install or enable power management functions of the operating system or other software, including
sleep states.
●
Turn off the computer before you do either of the following:
◦
Wipe the exterior of the computer with a soft, damp cloth as needed. Using cleaning products may
discolor or damage the finish.
◦
Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign
matter can block the vents and limit the airflow.
Computer operating guidelines and routine care 51
Optical drive precautions
Be sure to observe the following guidelines while operating or cleaning the optical drive.
Operation
●
Do not move the drive during operation. This may cause it to malfunction during reading.
●
Avoid exposing the drive to sudden changes in temperature, as condensation may form inside the unit. If
the temperature suddenly changes while the drive is on, wait at least one hour before you turn off the
power. If you operate the unit immediately, it may malfunction while reading.
●
Avoid placing the drive in a location that is subject to high humidity, extreme temperatures, mechanical
vibration, or direct sunlight.
Cleaning
●
Clean the panel and controls with a soft, dry cloth or a soft cloth lightly moistened with a mild detergent
solution. Never spray cleaning fluids directly on the unit.
●
Avoid using any type of solvent, such as alcohol or benzene, which may damage the finish.
Safety
If any object or liquid falls into the drive, immediately unplug the computer and have it checked by an
authorized HP service provider.
Shipping preparation
Follow these suggestions when preparing to ship the computer:
1. Back up the hard drive files to an external storage device. Be sure that the backup media is not exposed
to electrical or magnetic impulses while stored or in transit.
NOTE: The hard drive locks automatically when the system power is turned off.
2. Remove and store all removable media.
3. Turn off the computer and external devices.
4. Disconnect the power cord from the AC outlet, then from the computer.
5. Disconnect the system components and external devices from their power sources, then from the
computer.
NOTE: Be sure that all boards are seated properly and secured in the board slots before shipping the
computer.
6. Pack the system components and external devices in their original packing boxes or similar packaging
with sufficient packing material to protect them.
52 Appendix C Computer operating guidelines, routine care and shipping preparation
D Accessibility
HP designs, produces, and markets products and services that can be used by everyone, including people with
disabilities, either on a stand-alone basis or with appropriate assistive devices.
Supported assistive technologies
HP products support a wide variety of operating system assistive technologies and can be configured to work
with additional assistive technologies. Use the Search feature on your device to locate more information
about assistive features.
NOTE: For additional information about a particular assistive technology product, contact customer support
for that product.
Contacting support
We are constantly refining the accessibility of our products and services and welcome feedback from users. If
you have an issue with a product or would like to tell us about accessibility features that have helped you,
please contact us at (888) 259-5707, Monday through Friday, 6 a.m. to 9 p.m. Mountain Time. If you are deaf
or hard-of-hearing and use TRS/VRS/WebCapTel, contact us if you require technical support or have
accessibility questions by calling (877) 656-7058, Monday through Friday, 6 a.m. to 9 p.m. North American
Mountain Time.
NOTE: Support is in English only.
Supported assistive technologies 53
Index
A
installing
secondary 3.5-inch hard drive
access panel
removal
battery 47
replacement
accessibility 53
memory 15
secondary 3.5-inch hard drive
S
security
B
padlock 40
C
serial number location
L
specifications
memory 15
D
locks
DIMMs. See memory
drives
padlock 40
installation 23
locations 22
T
M
E
V
memory
installation 15
electrostatic discharge, preventing
damage 50
expansion card
installation 18
removal 18
specifications 15
O
optical drive
cleaning 52
F
front bezel
installation 25
precautions 52
removal 24
blank removal
removal
replacement 10
security 46
P
front panel components
product ID location
H
R
hard drive (2.5-inch)
installation 37
removal 35
hard drive (3.5-inch)
rear panel components
removing
battery 47
bezel blank
computer access panel
I
front bezel
installation guidelines
54 Index
|