HP EliteBook 8440p Notebook PC and
HP EliteBook 8440w Mobile Workstation
Maintenance and Service Guide
Document Part Number: 592258-001
January 2010
This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides
comprehensive information on identifying computer features, components, and spare parts; troubleshooting
computer problems; and performing computer disassembly procedures.
Safety warning notice
WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly
on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface,
such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow
the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of
Information Technology Equipment (IEC 60950).
Å
Contents
Identifying hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Top components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
Display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
Wireless antennas (select models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Buttons, switches, and fingerprint reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Pointing devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Front components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
Rear components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
Right-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
Left-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
Bottom components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
Serial number location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Computer major components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Display assembly subcomponents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Cable kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Plastics kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Mass storage devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–12
Miscellaneous parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13
Sequential part number listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14
Preliminary replacement requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Service considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Grounding guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Component replacement procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Service tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Computer feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
WLAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11
WWAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
Memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–16
Optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–20
Maintenance and Service Guide
iv
Contents
Keyboard and switch cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–22
Power button board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–26
Display assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–27
Fan and heat sink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–35
RTC battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–39
Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–40
Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–42
Audio/ExpressCard board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–44
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–45
Bluetooth module and cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–46
Modem module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–49
System board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–50
Modem module cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–52
Computer Setup in Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Computer Setup menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2
Computer Setup in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Computer Setup menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–9
Computer Setup in Windows XP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
Starting Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
Using Computer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–14
Computer Setup menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–15
Computer specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
14.0-in SVA eDP display specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–2
Hard drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–3
Solid state drive specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
Blu-ray R/RE DVD RW SuperMulti Drive specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5
Blu-ray ROM with LightScribe DVD RW SuperMulti DL Drive specifications . . . . . . . . . . . . . . . . . . . 6–6
DVD RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe . . . . . . . . . . . . . . . . . 6–7
DVD-ROM Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–8
System resource specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–9
Backup and recovery in Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
Backup and recovery in Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–6
Backup and recovery in Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
v
Maintenance and Service Guide
Contents
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
Performing a recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–10
Audio-out (headphone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
Audio-in (microphone). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1
1394a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–2
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–2
DisplayPort. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3
RJ-11 (modem). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
RJ-45 (network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
Universal Serial Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
eSATA/USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–6
Requirements for all countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
Requirements for specific countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Maintenance and Service Guide
vi
1
Product description
HP EliteBook HPEliteBook HPEliteBook
8440p
8440p
8440w
Notebook PC Notebook PC Mobile
Category
Description
UMA
Discrete
Workstation
Product Name
HP EliteBook 8440p Notebook PC
HP EliteBook 8440w Mobile Workstation
Intel® Core™ i5 dual-core processors:
Processors
i5-520M, 2.4-GHz processor (Turbo up to
2.93 GHz), 3-MB L3 cache, 4 threads (35W)
i5-540M, 2.53-GHz processor (Turbo up to
3.06 GHz), 3-MB L3 cache, 4 threads (35W)
Intel® Core™ i7 dual-core processors:
i7-620M, 2.66-GHz processor (Turbo up to
3.33GHz), 4-MB L3 cache, 4 threads (35W)
Intel® Core™ i7 quad-core, processors:
i7-720QM, 1.6-GHz processor (Turbo up to
2.8 GHz),
i7-820QM, 1.73-GHz processor (Turbo up to
3.06 GHz), 8-MB L3 cache, 8 threads (45W)
Chipset
Intel® PCH QM57 - Enhanced
Graphics
Intel® Unified Memory Architecture (UMA)
graphics subsystem integrated with shared system
memory (dynamically allocated; Intel® Graphics
Media Accelerator HD)
Nvidia N10M-NS discrete graphics card with
512 MB of GDDR3 800 MHz graphics subsystem
memory
Nvidia N10M-GLM NS discrete graphics card with
512 MB GDDR3 800 MHz (64 MB x 16 x 4)
graphics subsystem memory
Panel
All display assemblies include three wireless local
area network (WLAN) antennas and two wide-area
network antennas (WWAN)
14.0-in 16:9 HD (1366 x 768) AntiGlare LED
display
14.0-in 16:9 HD (1366 x 768) AntiGlare LED
display with webcam
14.0-in 16:9 HD+ (1600 x 900) AntiGlare LED
display
(Continued)
Maintenance and Service Guide
1–1
Product description
HP EliteBook HPEliteBook HPEliteBook
8440p 8440p 8440w
Notebook PC Notebook PC Mobile
Category
Memory
Description
UMA
Discrete
Workstation
14.0-in 16:9 HD+ (1600 x 900) AntiGlare LED
display with webcam
Support privacy filter
Two customer-accessible/upgradable memory
module slots
Supports dual-channel memory
DDR3 PC3-10600 1333-MHz memory
Supports the following configurations:
■ 8192-MB total system memory (4096 x 2)
■ 4096-MB total system memory (4096 x 1)
■ 4096-MB total system memory (2048 x 2)*
■ 3072-MB total system memory (2048 + 1024)*
■ 2048-MB total system memory (2048 x 1)*
■ 2048-MB total system memory (1024 x 2)*
■ 1024-MB total system memory (1024 x 1)*
*Brazil 1333-MHz memory configuration
Hard drives
Supports 9.5-mm, 6.35-cm (2.5-in) hard drives
Customer-accessible
Serial ATA
Supports the following drives:
■ 500 GB, 7200 rpm
■ 320 GB, 7200 rpm
■ 250 GB, 7200 rpm
Supports the following solid-state drives:
■ 256 GB
■ 160 GB
HP 3D DriveGuard
RAID 0/1 Support
Optical drives
Fixed (removal of 1 screw required)
Customer-accessible
Serial ATA
12.7-mm (0.50-in) drive tray
Supports the following drives:
■ Blu-ray R/RE DVD RW SuperMulti Drive
■ Blu-ray ROM with LightScribe DVD RW
SuperMulti DL Drive
■ DVD RW and CD-RW SuperMulti Double-Layer
Combo Drive with LightScribe
■ DVD-ROM Drive
(Continued)
1–2
Maintenance and Service Guide
Product description
HP EliteBook HP EliteBook HPEliteBook
8440p
8440p
8440w
Notebook PC Notebook PC Mobile
Category
Description
UMA
Discrete
Workstation
Upgrade drive bay
9.5-mm, 6.35-cm (2.50-in) HDDs
500 GB 7200 rpm
Supports "No Drive" option
Supports external USB diskette drive only
Integrated dual-array microphone
HD audio
Diskette drive
Microphone
Audio
Two stereo speakers
Webcam
Modem
Integrated 2.0-megapixel webcam
High-speed 56k modem
Modem cable not included
Support for No-Modem option in the Asia Pacific,
Japan, and Latin America regions
Ethernet
Wireless
Intel 10/100/1000 network interface card (NIC) with
iAMT
S3/S4/S5 wake on LAN
NIC power down technology
Ethernet cable not included
Integrated wireless local-area network (WLAN)
options by way of WLAN module:
Three WLAN antennas built into display assembly
Support for no WLAN option
Support for the following WLAN formats:
Broadcom b/g
Intel 802.11a/b/g
Intel 802.11a/g/n 2×2
Intel 802.11a/g/n 3×3
Integrated wireless wide-area network (WWAN)
options by way of WWAN module:
Two five-band WWAN antennas built into display
assembly
Subscriber identity module (SIM) security
(customer-accessible in battery bay)
Support for the following WWAN formats:
■ Qualcomm WW evolution-data optimized
(EVDO), high-speed downlink packet access
(HSDPA)
■ Ericsson HSDPA
Supports WWAN after-market options
Integrated personal area network (PAN) options by
way of Bluetooth® module
Support for no PAN option
(Continued)
Maintenance and Service Guide
1–3
Product description
HP EliteBook HPEliteBook HPEliteBook
8440p 8440p 8440w
Notebook PC Notebook PC Mobile
Category
Description
UMA
Discrete
Workstation
Digital card
One ExpressCard/54 slot
Integrated secure digital (SD)/ MultiMedia card
(MMC) card reader
Ports
Audio-in (stereo microphone)
Audio-out (stereo headphone)
DisplayPort digital display interface
RJ-11; modem
RJ-45; Ethernet, with link and activity lights
USB 2.0 (3)
USB 2.0/eSATA combo (1)
VGA (D-sub 15) supporting 1600 × 1200 external
monitor at 75-Hz (hot plug/unplug with auto-detect)
1394a
Multi-pin AC port
Docking
HP docking station
HP advanced docking station
11.97-in keyboard with embedded numeric keypad
Keyboard/pointing
devices
Spill-resistant keyboard
Dura-Keys
Vertical and horizontal scrolling, taps enabled as
default
Dual point (pointing stick and TouchPad) with 2
pointing stick buttons and 2 TouchPad buttons and
vertical scrolling (taps enabled as default)
Power requirements Supports the following AC adapter with localized
cable plug (3-wire plug with ground pin and 3-pin
DC connector):
65-W “Smart” adapter
90-W “Smart” adapter
9 cell Li-ion battery (100 Wh) 3.0 Ah (does not
support HP Fast Charge)
6 cell Li-ion battery (55 Wh) 2.55 Ah
6 cell 1000-cycle battery (51 Wh) 2.55 Ah
4 cell Li-ion battery (37 Wh) 2.55 Ah
Support for 8-cell Li-ion Extended Life battery
Support for 12-cell Ultra Capacity battery
(Continued)
1–4
Maintenance and Service Guide
Product description
HP EliteBook HP EliteBook HPEliteBook
8440p
8440p
8440w
Notebook PC Notebook PC Mobile
Category
Security
Description
UMA
Discrete
Workstation
Integrated HP Fingerprint sensor (select models
only)
Integrated smart card reader
Security cable slot
Trusted platform module (TPM) V.1.2
Full volume encryption
Preboot authentication (password, smart card,
biometric)
Operating system
Preinstalled:
Vista Basic 32 with Microsoft Basics
Windows XP Professional SP3 (EN, FR, JP) with
Microsoft Basics
Windows Vista Business SP1 32 with Microsoft
Basics
Windows 7 Home Premium 32 with Microsoft
Basics (Japan only)
Windows 7 Home Premium 64 with Microsoft
Basics (Japan only)
Windows 7 Professional 32 with Microsoft Basics
(Japan only)
Windows 7 Professional 64 with Microsoft Basics
(Japan only)
XP Professional SP3 with Microsoft Basics (with
Windows 7 Professional COA; Japan only)
FreeDOS
Preinstalled with Office:
Vista Basic 32 with Office 2007 Ready (not
available for Japan)
Vista Basic 32 with Office 2007 Personal (Japan
only)
Vista Basic 32 with Office 2007 Personal with
PowerPoint (Japan only)
Vista Basic 32 with Office Professional (Japan
only)
Windows Vista Business 32 with Office Ready (not
available for Japan)
Windows Vista Business 32 with Personal (Japan
only)
Windows Vista Business 32 with Personal and
PowerPoint (Japan only)
Windows Vista Business 32 with Professional
(Japan only)
(Continued)
Maintenance and Service Guide
1–5
Product description
HP EliteBook HPEliteBook HPEliteBook
8440p 8440p 8440w
Notebook PC Notebook PC Mobile
Category
Description
UMA
Discrete
Workstation
Windows 7 Home Basic 32 with Office 2007 Ready
(not available for Japan)
Windows 7 Home Premium 32 with Office 2007
Ready (not available for Japan)
Windows 7 Home Premium 32 with Office 2007
Personal (Japan only)
Windows 7 Home Premium 32 with Office 2007
Personal with PowerPoint (Japan only)
Windows 7 Home Premium 32 with Office 2007
Professional (Japan only)
Windows 7 Home Premium 64 with Office 2007
Ready (not available for Japan)
Windows 7 Home Premium 64 with Office 2007
Personal (Japan only)
Windows 7 Home Premium 64 with Office 2007
Personal with PowerPoint (Japan only)
Windows 7 Home Premium 64 with Office 2007
Professional (Japan only)
Windows 7 Pro 32 with Office 2007 Ready (not
available for Japan)
Windows 7 Pro 32 with Office 2007 Personal
(Japan only)
Windows 7 Pro 32 with Office 2007 Personal with
PowerPoint (Japan only)
Windows 7 Pro 32 with Office Professional (Japan
only)
Windows 7 Pro 64 with Office 2007 Ready (not
available for Japan)
Windows 7 Pro 64 with Office 2007 Personal
(Japan only)
Windows 7 Pro 64 with Office 2007 Personal with
PowerPoint (Japan only)
Windows 7 Pro 64 with Office Professional (Japan
only)
Windows XP Pro (with Windows 7 Pro COA) with
Office Ready (not available for Japan)
Windows XP Pro (with Windows 7 Pro COA) with
Personal (Japan only)
Windows XP Pro (with Windows 7 Pro COA) with
Personal and PowerPoint (Japan only)
Windows XP Pro (with Windows 7 Pro COA) with
Professional (Japan only)
(Continued)
1–6
Maintenance and Service Guide
Product description
HP EliteBook HP EliteBook HPEliteBook
8440p
8440p
8440w
Notebook PC Notebook PC Mobile
Category
Description
UMA
Discrete
Workstation
Restore Media:
Windows Vista Ultimate 32
Windows Vista Business 32/64
Windows Vista Home Basic 32
Windows XP Professional
DRDVD Windows XP
DRDVD Windows Vista
DRDVD Windows 7
DRDVD Windows 7 with WinDVD
Windows XP Professional
Windows Vista Business 32
Windows Vista Business 64
Windows 7 Home Basic 32
Windows 7 Home Premium 32
Windows 7 Home Premium 64
Windows 7 Pro 32
Windows 7 Pro 64
Certified:
SUSE Linux Enterprise Desktop
Web-only Support:
Windows XP Pro 64
Windows Vista Business 64
Windows Vista Enterprise 32
Windows Vista Enterprise 64
Customer replaceable parts:
AC adapter
Serviceability
Battery (system)
Hard drive
Solid-state drive
Memory module
Optical drive
Mini-PCI components
Maintenance and Service Guide
1–7
2
External component identification
Identifying hardware
Components included with the computer may vary by region and model. The illustrations in this chapter identify
the standard features on most computer models.
To see a list of hardware installed in the computer, follow these steps:
In Windows® 7:
»
Select Start > Control Panel > System and Security > Device Manager.
You can also add hardware or modify device configurations using Device Manager.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
✎
In Windows Vista®:
1. Select Start > Computer > System Properties.
2. In the left pane, click Device Manager.
You can also add hardware or modify device configurations using Device Manager.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
In Windows XP:
1. Select Start > My Computer.
2. In the left pane of the System Tasks window, select View system information.
3. Select Hardware tab > Device Manager.
You can also add hardware or modify device configurations using Device Manager.
Maintenance and Service Guide
2–1
External component identification
Top components
Display components
The computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
Internal display switch
Turns off the display and initiates Sleep (Windows 7 and Windows Vista) or
Standby (Windows XP) if the display is closed while the power is on.
(2)
Internal microphones (2)
Record sound.
If there is a microphone icon next to each microphone opening, the
computer has internal microphones.
✎
(3)
(4)
(5)
Webcam light
Webcam
On: The webcam is in use.
Records video and captures still photographs.
Keyboard light
Illuminates the keyboard in low-light conditions. The keyboard light is
embedded in a push/push switch. You push the keyboard light cover to open
and turn the light on. Push again to close and turn the light off.
2–2
Maintenance and Service Guide
External component identification
Wireless antennas (select models only)
Item Component
Description
(1)
WWAN antennas (2)* (select
models only)
Send and receive wireless signals to communicate with wireless wide-area
networks (WWANs).
(2)
WLAN antennas (3)* (select
models only)
Send and receive wireless signals to communicate with wireless local area
networks (WLANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that
applies to your country or region. These notices are located in Help and Support.
Maintenance and Service Guide
2–3
External component identification
Buttons, switches, and fingerprint reader
Item Component
Description
(1)
Power button
■ When the computer is off, press the button to turn on the computer.
■ When the computer is on, press the button to shut down the computer.
Although you can shut down the computer with the power button, the
✎
recommended procedure is to use the Windows Shut Down command.
■ When the computer is in the Sleep state (Windows 7 and Windows Vista)
or Standby (Windows XP), press the button briefly to exit the Sleep state
(Windows 7 and Windows Vista) or Standby (Windows XP).
■ When the computer is in Hibernation, press the button briefly to exit
Hibernation.
If the computer has stopped responding and Windows shutdown procedures
are ineffective, press and hold the power button for at least 5 seconds to turn
off the computer.
To learn more about power settings:
■ In Windows 7: Select Start > Control Panel > System and Security >
Power Options.
■ In Windows Vista: Select Start > Control Panel > System and
Maintenance > Power Options.
■ In Windows XP: Select Start > Control Panel > Performance and
Maintenance > Power Options.
(2)
(3)
Internal display switch
QuickLook button
Turns off the display if the display is closed while the power is on.
Allows you to save calendar, contact, inbox, and task information from
Microsoft Outlook to the hard drive of the computer. When the computer is off
or in Hibernation, press the QuickLook button to view this information without
waiting for the operating system to restart.
(4)
(5)
QuickWeb button
Wireless button
Opens the Web browser.
Turns the wireless feature on or off but does not establish a wireless
connection
(Continued)
2–4
Maintenance and Service Guide
External component identification
Item Component
Description
(6)
TouchPad button
Turns the TouchPad on or off.
Turns caps lock on or off.
Turns num lock on or off.
Mutes and restores speaker sound.
Decreases speaker volume.
Increases speaker volume.
(7)
Caps lock button
Num lock button
(8)
(9)
Volume mute button
Volume down button
Volume up button
(10)
(11)
(12)
Fingerprint reader (select models
only)
Allows a fingerprint logon to Windows, instead of a password logon.
Maintenance and Service Guide
2–5
External component identification
Keys
The computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
(2)
esc key
Displays system information when pressed in combination with the fn key.
fn key
Executes frequently used system functions when pressed in combination with
a function key or the esc key.
(3)
(4)
(5)
Windows logo key
Displays the Windows Start menu.
Windows applications key
Embedded numeric keypad keys
Displays a shortcut menu for items beneath the pointer.
Use like an external numeric keypad when you enable the num lock function
by pressing the fn key in combination with the num lk key.
(6)
Function keys
Execute frequently used system functions when pressed in combination with
the fn key.
■ Display system information. fn+esc
■ Initiate Standby or Sleep. fn+f3
■ Switch the screen image. fn+f4
■ Display battery information. fn+f8
■ Decrease screen brightness. fn+f9
■ Increase screen brightness. fn+f10
■ Activate the ambient light sensor. fn+f11
2–6
Maintenance and Service Guide
External component identification
Pointing devices
Item Component
Description
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Pointing stick
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Functions like the right button on an external mouse.
Scrolls up or down.
Left pointing stick button
TouchPad*
Left TouchPad button*
Right pointing stick button
TouchPad scroll zone*
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences:
■ In Windows 7: Select Start > Devices and Printers. Then, right-click the device representing the computer, and select
Mouse settings.
■ In Windows Vista: Select Start > Control Panel > Hardware and Sound > Mouse.
■ In Windows XP: Select Start > Control Panel > Printers and Other Hardware > Mouse.
Maintenance and Service Guide
2–7
External component identification
Lights
The computer may look slightly different from the illustration in this section.
✎
Item Component
Description
(1)
Wireless lights (2)*
■ Blue: An integrated wireless device, such as a WLAN device, the
HP Mobile Broadband Module (select models only), and/or a Bluetooth®
device, is on.
■ Amber: All wireless devices are off.
(2)
Power lights (2)†
■ On: The computer is on.
■ Blinking: The computer is in the Sleep state (Windows 7 and
Windows Vista) or Standby (Windows XP).
■ Blinking rapidly: An AC adapter with a higher power rating should be
connected.
■ Off: The computer is off or in Hibernation.
(3)
Battery light
■ Amber: A battery is charging.
■ Turquoise: A battery is close to full charge capacity.
■ Blinking amber: A battery that is the only available power source has
reached a low battery level. When the battery reaches a critical battery
level, the battery light begins blinking rapidly.
■ Off: If the computer is plugged into an external power source, the light turns
off when all batteries in the computer are fully charged. If the computer is
not plugged into an external power source, the light stays off until the
battery reaches a low battery level.
(4)
Drive light
■ Blinking turquoise: The hard drive or optical drive is being accessed.
■ Amber: HP 3D DriveGuard has temporarily parked the internal hard drive,
and if present, the hard drive in the upgrade bay.
(5)
(6)
(7)
QuickLook light
QuickWeb light
TouchPad light
Turns on briefly when the QuickLook button is pressed.
Turns on briefly when the QuickWeb button is pressed.
■ Turquoise: The TouchPad is on.
■ Amber: The TouchPad is off.
(Continued)
2–8
Maintenance and Service Guide
External component identification
Item Component
Description
(8)
Caps lock light
Num lock light
Volume mute light
On: Caps lock is on.
(9)
On: Num lock is on or the embedded numeric keypad is enabled.
(10)
■ On: Computer sound is on.
■ Amber: Computer sound is off.
(11)
(12)
Volume down light
Volume up light
Blinking: The volume down button is being used to decrease the speaker
volume.
Blinking: The volume up button is being used to increase the speaker volume.
*The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
†The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
Maintenance and Service Guide
2–9
External component identification
Front components
Item Component
Description
(1)
Wireless light
■ Blue: An integrated wireless device, such as a wireless local area network
(WLAN) device, the HP Mobile Broadband Module, and/ or a Bluetooth®
device, is on.
■ Amber: All wireless devices are off.
(2)
Power light
■ On: The computer is on.
■ Blinking: The computer is in the Sleep state (Windows 7 and
Windows Vista) or Standby (Windows XP).
■ Blinking rapidly: An AC adapter with a higher power rating should be
connected.
■ Off: The computer is off or in Hibernation.
(3)
Battery light
■ Amber: A battery is charging.
■ Turquoise: A battery is close to full charge capacity.
■ Blinking amber: A battery that is the only available power source has
reached a low battery level. When the battery reaches a critical battery
level, the battery light begins blinking rapidly.
■ Off: If the computer is plugged into an external power source, the light turns
off when all batteries in the computer are fully charged. If the computer is
not plugged into an external power source, the light stays off until the
battery reaches a low battery level.
(4)
Drive light
■ Blinking turquoise: The hard drive or an external optical drive is being
accessed.
■ Amber: HP 3D DriveGuard has temporarily parked the hard drive, and if
present, the hard drive in the upgrade bay.
(5)
(6)
Business card slot
SD Card Reader
Holds a business card in position so that the webcam (select models only)
can capture an image.
Supports the optional Secure Digital (SD) Memory Card and MultiMediaCard
(MMC) digital card formats.
(7)
(8)
(9)
Display release button
Speakers (2)
Opens the computer.
Produce sound.
Bluetooth compartment
Contains a Bluetooth module.
2–10
Maintenance and Service Guide
External component identification
Rear components
Item Component
Description
(1)
Security cable slot
Attaches an optional security cable to the computer.
The security cable is designed to act as a deterrent, but it may not
prevent the computer from being mishandled or stolen.
✎
(2)
(3)
Power connector
DisplayPort
Connects an AC adapter.
Connects an optional digital display device such as a high-performance
monitor or projector.
(4)
External monitor port
Connects an external VGA monitor or projector.
Maintenance and Service Guide
2–11
External component identification
Right-side components
Item Component
Description
(1)
(2)
(3)
Smart card reader
Supports optional smart cards and Java™ cards.
Supports an optical drive or a hard drive.
Upgrade drive bay
eSATA/USB combo port
Connects an optional high-performance eSATA component, such as a
external mass-storage device, or connects an optional USB device.
(4)
(5)
RJ-45 (network) jack
RJ-11 (modem) jack
Connects a network cable.
Connects a modem cable.
Left-side components
Item Component
Description
(1)
Vent
Enables airflow to cool internal components.
The computer fan starts up automatically to cool internal components
✎
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
(2)
(3)
USB ports (3)
1394 port
Connects an optional USB devices.
Connects an optional IEEE 1394 or 1394a audio/visual device, such as a
camcorder.
(4)
(5)
ExpressCard slot
Supports optional ExpressCard/54 cards.
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo array
microphone, or monaural microphone.
(6)
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo speakers,
headphones, ear buds, a headset, or television audio
When a device is connected to the headphone jack, the computer
speakers are disabled.
✎
2–12
Maintenance and Service Guide
External component identification
Bottom components
Item Component
Description
(1)
(2)
(3)
Battery bay
Holds the battery.
Battery release latch
SIM slot (select models only)
Releases the battery from the battery bay.
Contains a wireless subscriber identity module (SIM). The SIM slot is located
inside the battery bay.
(4)
(5)
(6)
Docking connector
Accessory battery connector
Vents (7)
Connects an optional docking device.
Connects an optional accessory battery.
Enable airflow to cool internal components.
The computer fan starts up automatically to cool internal components
✎
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
(7)
Wireless module compartment
Contains a WWAN module (select models only) and/or WLAN module.
To prevent an unresponsive system, replace the wireless module only
with a wireless module authorized for use in the computer by the
Ä
governmental agency that regulates wireless devices in your country or
region. If you replace the module and then receive a warning message,
remove the module to restore computer functionality, and then contact
technical support through Help and Support.
(8)
Business card holder
Memory module compartment
Hard drive bay
Holds a business card.
(9)
Contains the expansion memory module slot.
Secures the hard drive.
(10)
Maintenance and Service Guide
2–13
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number located on
the bottom of the computer.
Service tag color varies on select models.
✎
The service tag provides the following information:
(1) Product name: This is the product name affixed to the front of the computer.
(2) Serial: This is an alphanumeric identifier that is unique to each product.
(3) Product: This number provides specific information about the product's hardware components. The part
number helps a service technician to determine what components and parts are needed.
(4) Warranty: The number describes the duration of the warranty period for the computer.
(5) Model: This is the number used to locate documents, drivers, and support for the computer.
Warranty and Model fields are excluded from the service tag on select models.
✎
Maintenance and Service Guide
3–1
Illustrated parts catalog
Item Description
(1) Display assembly - 14.0-in, antiglare display for use with computer models equipped with
Spare part number
WLAN and WWAN capability (includes 3 transmit/receive WLAN antenna, 2 transmit/receive
WWAN antenna, and cables):
14.0-in HD AntiGlare LED SVA (1366x768) for use with HP EliteBook 8440p
14.0-in HD AntiGlare LED SVA (1366x768) with webcam for use with HP EliteBook 8440p
14.0-in HD+ AntiGlare LED SVA (1600x900) for use with HP EliteBook 8440p
594087-001
594088-001
594089-001
14.0-in HD+ AntiGlare LED SVA (1600x900) with webcam for use with HP EliteBook 8440p 594090-001
14.0-in HD AntiGlare LED SVA (1366x768) for use with HP EliteBook 8440w
14.0-in HD AntiGlare LED SVA (1366x768) with webcam for use with HP EliteBook 8440w
14.0-in HD+ AntiGlare LED SVA (1600x900) for use with HP EliteBook 8440w
598210-001
598211-001
598212-001
14.0-in HD+ AntiGlare LED SVA (1600x900) with webcam for use with HP EliteBook 8440w 598213-001
for more display assembly subcomponent information.
Display cable
594037-001
594029-001
594039-001
594038-001
594223-001
594035-001
594036-001
594756-001
594757-001
594031-001
594032-001
594033-001
594034-001
Ambient light sensor/connector board
Display hinge/bracket (left and right)
Display hinge cover (left and right) for use with HP EliteBook 8440p
Display hinge cover (left and right) for use with HP EliteBook 8440w
Display bezel without webcam lens for HP EliteBook 8440p
Display bezel with webcam lens for HP EliteBook 8440p
Display bezel without webcam lens for HP EliteBook 8440w
Display bezel with webcam lens for HP EliteBook 8440w
Display back cover with webcam for use with HP EliteBook 8440p
Display back cover with webcam for use with HP EliteBook 8440w
Display back cover without webcam for use with HP EliteBook 8440p
Display back cover without webcam for use with HP EliteBook 8440w
Switch cover
(2)
Switch cover with LED board for use with HP EliteBook 8440p
Switch cover with LED board for use with HP EliteBook 8440w
Power button board with cable
594095-001
594096-001
594025-001
(3)
(4)
Keyboards (include keyboard cable)
For use in Brazil
594052-201
594052-261
594052-221
594052-081
594052-B31
594052-A41
594052-051
594052-121
For use in Bulgaria
For use in Czech Republic
For use in Denmark
For use in Europe
For use in Europe A4
For use in France
For use in French Canada
(Continued)
Maintenance and Service Guide
3–3
Illustrated parts catalog
Item Description
For use in Germany
Spare part number
594052-041
594052-DJ1
594052-211
594052-DD1
594052-BB1
594052-061
594052-291
594052-161
594052-091
594052-131
594052-251
594052-171
594052-231
594052-BA1
594052-AD1
594052-071
594052-B71
594052-BG1
594052-AB1
594052-281
594052-141
594052-031
594052-001
594049-001
For use in Greece
For use in Hungry
For use in Iceland
For use in Israel
For use in Italy
For use in Japan
For use in Latin America
For use in Norway
For use in Portugal
For use in Russia
For use in Saudi Arabia
For use in Slovakia
For use in Slovenia
For use in South Korea
For use in Spain
For use in Sweden/Finland
For use in Switzerland
For use in Taiwan
For use in Thailand
For use in Turkey
For use in United Kingdom
For use in United States
Fan
(5)
(6)
Heat sink
For use with discrete graphics subsystem
For use with Unified Memory Architecture (UMA) graphics subsystem
594050-001
594051-001
Plastics kit with plastic screw covers, ExpressCard blank, RJ11 plug, and fingerprint reader 594091-001
(7a) ExpressCard slot bezel
(7b) Hard drive bay cover
(7c) Memory module compartment cover
(7d) WLAN and WWAN module compartment cover
(7e) Bluetooth module compartment cover
Cable kit (includes Bluetooth cable and modem cable with RJ11 connector)
594030-001
information.
(Continued)
3–4
Maintenance and Service Guide
Illustrated parts catalog
Item Description
(9) Processors (include replacement thermal material)
Spare part number
Intel® Core™ i5 dual-core processor:
i5-520M, 2.4-GHz processor (Turbo up to 2.93 GHz) 3-MB L3 cache, 4 threads (35W)
i5-540M, 2.53-GHz processor (Turbo up to 3.06 GHz) 3-MB L3 cache, 4 threads (35W)
Intel® Core™ i7 quad-core, processor:
594187-001
594188-001
i7-620M, 2.66-GHz processor (Turbo up to 3.33 GHz) 6-MB L3 cache, 8 threads (45W)
Intel® Core™ i7 quad-core, processor:
587259-001
i7-720QM, 1.6-GHz processor (Turbo up to 2.8 GHz), 6-MB L3 cache, 8 threads (45W)
i7-820QM, 1.73-GHz processor (Turbo up to 3.06 GHz), 8-MB L3 cache, 8 threads (45W)
586170-001
583053-001
(10) Primary memory modules (PC3-10600 DDR3 1333-MHz)
1024-MB
598859-001
598856-001
599092-001
581075-001
2048-MB
4096-MB
(11) RTC battery (includes cable and double-sided tape)
(12) Top cover with Touchpad, cable, and bracket
Top cover with smart card reader (13) and fingerprint reader (14) for HP EliteBook 8440p
Top cover with smart card reader (13) and fingerprint reader (14) for HP EliteBook 8440w
594098-001
594099-001
594100-001
Top cover with smart card reader (13) without fingerprint reader for HP EliteBook 8440w
(Plastics kit includes fingerprint reader plug)
(15) Audio/ExpressCard board
594024-001
(16) System board with replacement thermal material
System board for use with HP EliteBook 8440p discrete graphics subsystem
System board for use with HP EliteBook 8440w discrete graphics subsystem
System board for use with HP EliteBook 8440p UMA graphics subsystem
(17) Speaker assembly
594026-001
594027-001
594028-001
594094-001
(18) Modem module (without cable)
The modem module cable is included in the Cable kit, spare part number 594030-001.
✎
High-speed 56K modem for use in all countries and regions except Australia and New
Zealand
510099-001
510099-011
High-speed 56K modem for use in Australia and New Zealand
(19) Battery
4 cell, 2.55-Ah (37-Wh) Li-ion battery
6 cell, 2.55-Ah (55-Wh) Li-ion battery
6 cell, 2.55-Ah (51-Wh) 1000-cycle battery
9 cell, 3.0-Ah (100-Wh) Li-ion battery
(20) Base enclosure
489961-001
486296-001
593578-001
593579-001
Base enclosure for use with HP EliteBook 8440p
Base enclosure for use with HP EliteBook 8440w
594021-001
594022-001
(Continued)
Maintenance and Service Guide
3–5
Illustrated parts catalog
Item Description
Spare part number
(21) Optical drives (12.7mm SATA) with optical drive bezel and bracket or optional upgrade hard
drive
Blu-ray ROM DVD RW SuperMulti DL Drive
Blu-ray R/RE DVD RW SuperMulti Drive
DVD-ROM Drive
594040-001
594041-001
594042-001
594043-001
DVD RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
(22) Mass storage devices with bracket
250-GB 7200-rpm SATA hard drive
320-GB 7200-rpm SATA hard drive
500-GB 7200-rpm SATA hard drive (also used for optional upgrade bay hard drive)
160-GB solid-state drive
594044-001
594045-001
594046-001
594047-001
594048-001
256-GB solid-state drive
(23) Expansion memory modules (PC3-10600 DDR3 1333-MHz)
1024-MB
598859-001
598856-001
599092-001
2048-MB
4096-MB
(24) WLAN modules
Intel a/g/n (2x2) for use in all countries and regions
Intel a/g/n (3x3) for use in all countries and regions
Intel a/b/g for use in Russia
572509-001
572511-001
572510-001
504593-003
Broadcom BCM4312 802.11b/g WLAN module for use in Canada, the Cayman Islands,
Guam, Puerto Rico, the United States, and the U.S. Virgin Islands
(Continued)
3–6
Maintenance and Service Guide
Illustrated parts catalog
Item Description
Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria,
Spare part number
504593-004
Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azer-
baijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Ber-
muda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands,
Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central
African Republic, Chad, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the
Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecua-
dor, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France,
French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan,
Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Nor-
way, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic
of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania,
Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Ser-
bia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vin-
cent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajiki-
stan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbeki-
stan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
(25) WWAN Modules
Qualcomm EV-DO HSPA minicard
Ericsson F3607 SDG 900 HSPA minicard
(26) Bluetooth module (without cable)
531993-001
574249-001
537921-001
The Bluetooth module cable is included in the Cable kit, spare part number
✎
Maintenance and Service Guide
3–7
Illustrated parts catalog
Display assembly subcomponents
Item Description
(1) Display bezel
Spare part number
Bezel with webcam lens for HP EliteBook 8440w Mobile Workstation
594757-001
594756-001
594036-001
594035-001
Bezel without webcam lens for HP EliteBook 8440w Mobile Workstation
Bezel with webcam lens for HP EliteBook 8440p Notebook PC
Bezel without webcam lens for HP EliteBook 8440p Notebook PC
(2) Display panel
(3) Display cable
594037-001
594039-001
594223-001
594038-001
594029-001
(4) Display hinge/bracket (left and right)
Hinge cap (left and right) for HP EliteBook 8440w Mobile Workstation
Hinge cap (left and right) for HP EliteBook 8440p Notebook PC
(5) Ambient light sensor/connector board
(Continued)
3–8
Maintenance and Service Guide
Illustrated parts catalog
(6) Back cover includes the dual-array microphone and cable, wireless antennas and
cables
Back cover with webcam for HP EliteBook 8440w Mobile Workstation
Back cover without webcam for HP EliteBook 8440w Mobile Workstation
Back cover with webcam for HP EliteBook 8440p Notebook PC
Back cover without webcam for HP EliteBook 8440p Notebook PC
594032-001
594034-001
594031-001
594033-001
Maintenance and Service Guide
3–9
Illustrated parts catalog
Plastics kit
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the
plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Ä
Item Description
Plastics kit:
Spare part number
594091-001
(1)
(2)
(3)
(4)
(5)
ExpressCard slot bezel
Hard drive bay cover (includes one captive screw, secured by a C-clip)
Wireless module compartment cover (includes one captive screw)
Expansion memory compartment cover
Bluetooth module compartment cover
Maintenance and Service Guide
3–11
Illustrated parts catalog
Mass storage devices
Item Description
Spare part number
(1)
Hard drives (includes bracket, screws, and sponge material)
250-GB 7200-rpm SATA hard drive
594044-001
594045-001
594046-001
320-GB 7200-rpm SATA hard drive
500-GB 7200-rpm SATA hard drive
(2)
Optical drives (includes drive bezel, bracket, and rubber covers)
Blu-ray ROM with LightScribe DVD RW SuperMulti DL Drive
Blu-ray R/RE DVD RW SuperMulti Drive
DVD-ROM Drive
594040-001
594041-001
594042-001
594043-001
DVD RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
Solid-state drives
(3)
160-GB solid-state drive
594047-001
594048-001
256-GB solid-state drive
3–12
Maintenance and Service Guide
Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
Rubber kit with rubber screw covers for upgrade-bay, top cover back, display screw covers, 594092-001
base enclosure screw covers, and rubber feet
AC adapter
90W AC adapter
463955-001
535593-001
463958-001
577170-001
90W AC adapter for use in India
65W AC adapter
65W AC adapter for use in India
Power cords:
For use in Argentina
490371-D01
490371-011
490371-202
490371-081
490371-021
490371-D61
490371-BB1
490371-061
490371-291
490371-001
490371-AR1
490371-AD1
490371-111
490371-AB1
490371-AA1
490371-031
594097-001
598214-001
594093-001
For use in Australia
For use in Brazil
For use in Denmark
For use in Europe
For use in India
For use in Israel
For use in Italy
For use in Japan
For use in North America
For use in South Africa
For use in South Korea
For use in Switzerland
For use in Taiwan
For use in the People's Republic of China
For use in the United Kingdom and Singapore
Thermal heatshield (includes thermal support items)
CPU Mylar (processor support item)
Screw kit (includes 15 of each of the following screws)
Phillips PM2.0×2.0×7.0 (broad-head)
Phillips PM2.0×3.0×4.5
Phillips PM2.0×4.0×4.5
Phillips PM2.5×3.0×4.5
Phillips PM2.5×4.0×4.5
Phillips PM 2.5×5.0×4.5
Torx T8 M2.5×6.0×5.0
Phillips PM2.8×4.0×5.0
Phillips PM3.0×3.0×5.0
Maintenance and Service Guide
3–13
Illustrated parts catalog
Sequential part number listing
Spare part number
463955-001
463958-001
486296-001
489961-001
490371-001
490371-011
490371-021
490371-031
490371-061
490371-081
490371-111
490371-202
490371-291
490371-AA1
490371-AB1
490371-AD1
490371-AR1
490371-BB1
490371-D01
490371-D61
504593-003
Description
90W AC adapter
65W AC adapter
Battery 6 cell, 2.55-Ah (55-Wh) Li-ion
Battery 4 cell, 2.55-Ah (37-Wh) Li-ion
Power cord for use in North America
Power cord for use in Australia
Power cord for use in Europe
Power cord for use in the United Kingdom and Singapore
Power cord for use in Italy
Power cord for use in Denmark
Power cord for use in Switzerland
Power cord for use in Brazil
Power cord for use in Japan
Power cord for use in the People's Republic of China
Power cord for use in Taiwan
Power cord for use in South Korea
Power cord for use in South Africa
Power cord for use in Israel
Power cord for use in Argentina
Power cord for use in India
Broadcom BCM4312 802.11b/g WLAN module for use in Canada, the Cayman
Islands, Guam, Puerto Rico, the United States, and the U.S. Virgin Islands
(Continued)
3–14
Maintenance and Service Guide
Illustrated parts catalog
504593-004
Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania,
Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia,
Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium,
Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary,
Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco,
Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua
New Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland,
Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra
Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa,
South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the
Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan,
Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
510099-001
High-speed 56K modem for use in all countries and regions except Australia and New
Zealand
510099-011
531993-001
535593-001
537921-001
572509-001
572510-001
572511-001
574249-001
577170-001
581075-001
583053-001
High-speed 56K modem for use in Australia and New Zealand
Qualcomm EV-DO HSPA WWAN module
90W AC adapter for use in India
Bluetooth module without cable
Intel a/g/n (2 x 2) WLAN module
Intel a/b/g WLAN module for use in Europe, Middle-East, and Africa
Intel a/g/n (3 x 3) WLAN module
Ericsson F3607 SDG 900 HSPA WWAN module
65W AC adapter for use in India
RTC battery
i7-820QM, 1.73-GHz Intel® Core™ i7 quad-core processor Turbo up to 3.06 GHz),
8-MB L3 cache, 8 threads (45W)
586170-001
587259-001
i7-720QM, 1.6-GHz Intel® Core™ i7 quad-core processor (Turbo up to 2.8 GHz), 6-MB
L3 cache, 8 threads (45W)
i7-620M, 2.66-GHz Intel® Core™ i7 quad-core processor (Turbo up to 3.33 GHz),
6-MB L3 cache, 8 threads (45W)
593578-001
593579-001
594021-001
594022-001
594024-001
6 cell, 2.55-Ah (51-Wh) 1000-cycle battery
9 cell, 3.0-Ah (100-Wh) Li-ion battery
Base enclosure for use with HP EliteBook 8440p
Base enclosure for use with HP EliteBook 8440w
Audio/ExpressCard board
(Continued)
Maintenance and Service Guide
3–15
Illustrated parts catalog
594025-001
Power button board with cable
594026-001
594027-001
594028-001
594029-001
594030-001
594031-001
594032-001
594033-001
594034-001
594035-001
594036-001
594037-001
594038-001
594039-001
594040-001
System board for use with HP EliteBook 8440p discrete graphics subsystem
System board for use with HP EliteBook 8440w discrete graphics subsystem
System board for use with HP EliteBook 8440p UMA graphics subsystem
Ambient light sensor/connector board
Cable kit (includes Bluetooth cable and modem cable with RJ11 connector)
Display back cover with webcam for use with HP EliteBook 8440p
Display back cover with webcam for use with HP EliteBook 8440w
Display back cover without webcam for use with HP EliteBook 8440p
Display back cover without webcam for use with HP EliteBook 8440w
Display bezel without webcam lens for HP EliteBook 8440p
Display bezel with webcam lens for HP EliteBook 8440p
Display cable
Display hinge cover (left and right) for use with HP EliteBook 8440p
Display hinge/bracket (left and right)
Blu-ray ROM with LightScribe DVD RW SuperMulti DL Drive (12.7mm SATA) with
bezel and bracket
594041-001
594042-001
594043-001
Blu-ray R/RE DVD RW SuperMulti Drive (12.7mm SATA) with bezel and bracket
DVD-ROM Drive (12.7mm SATA) with bezel and bracket
DVD RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
(12.7mm SATA) with bezel and bracket
594044-001
594045-001
594046-001
594047-001
594048-001
594049-001
594050-001
594051-001
594052-001
594052-031
594052-041
594052-051
594052-061
594052-071
594052-081
594052-091
594052-121
594052-131
594052-141
250-GB 7200-rpm SATA hard drive
320-GB 7200-rpm SATA hard drive
500-GB 7200-rpm SATA hard drive
160-GB solid-state drive
256-GB solid-state drive
Fan
Heat sink for use with discrete graphics subsystem
Heat sink for use with Unified Memory Architecture (UMA) graphics subsystem
Keyboard for use in United States
Keyboard for use in United Kingdom
Keyboard for use in Germany
Keyboard for use in France
Keyboard for use in Italy
Keyboard for use in Spain
Keyboard for use in Denmark
Keyboard for use in Norway
Keyboard for use in French Canada
Keyboard for use in Portugal
Keyboard for use in Turkey
(Continued)
3–16
Maintenance and Service Guide
Illustrated parts catalog
594052-161
594052-171
594052-201
594052-211
594052-221
594052-231
594052-251
594052-261
594052-281
594052-291
594052-A41
594052-AB1
594052-AD1
594052-B31
594052-B71
594052-BA1
594052-BB1
594052-BG1
594052-DD1
594052-DJ1
594087-001
594088-001
594089-001
594090-001
594091-001
Keyboard for use in Latin America
Keyboard for use in Saudi Arabia
Keyboard for use in Brazil
Keyboard for use in Hungry
Keyboard for use in Czech Republic
Keyboard for use in Slovakia
Keyboard for use in Russia
Keyboard for use in Bulgaria
Keyboard for use in Thailand
Keyboard for use in Japan
Keyboard for use in Europe A4
Keyboard for use in Taiwan
Keyboard for use in South Korea
Keyboard for use in Europe
Keyboard for use in Sweden/Finland
Keyboard for use in Slovenia
Keyboard for use in Israel
Keyboard for use in Switzerland
Keyboard for use in Iceland
Keyboard for use in Greece
Display assembly, 14.0-in, HD AntiGlare LED SVA (1366 x 768)
Display assembly, 14.0-in, HD AntiGlare LED SVA (1366 x 768) with webcam
Display assembly, 14.0-in, HD+ AntiGlare LED SVA (1600 x 900)
Display assembly, 14.0-in, HD+ AntiGlare LED SVA (1600 x 900) with webcam
Plastics kit with plastic screw covers, ExpressCard blank, RJ11 plug, and fingerprint
reader plug
594092-001
594093-001
Rubber kit with rubber screw covers for upgrade-bay, top cover back, LCD screw
covers, base enslosure, and rubber feet
Screw kit (includes 15 of each of the following screws)
Phillips PM2.0×2.0×7.0 (broad-head)
Phillips PM2.0×3.0×4.5
Phillips PM2.0×4.0×4.5
Phillips PM2.5×3.0×4.5
Phillips PM2.5×4.0×4.5
Phillips PM2.5×5.0×4.5
Torx T8 M2.5×6.0×5.0
Phillips PM2.8×4.0×5.0
Phillips PM3.0×3.0×5.0
594094-001
594095-001
594096-001
594097-001
Speaker assembly
Switch cover with LEB board for use with HP EliteBook 8440p
Switch cover with LED board for use with HP EliteBook 8440w
Thermal heatshield (includes thermal support items)
(Continued)
Maintenance and Service Guide
3–17
Illustrated parts catalog
594098-001
Top cover with integrated Touchpad, smart card reader, and fingerprint reader for use
with HP EliteBook 8440p
594099-001
594100-001
594187-001
594188-001
Top cover with integrated Touchpad, smart card reader, and fingerprint reader for use
with HP EliteBook 8440w
Top cover with integrated Touchpad, smart card reader, and without fingerprint reader
for use with HP EliteBook 8440w
i5-520M, 2.4-GHz Intel® Core™ i5 dual-core processor, (Turbo up to 2.93 GHz), 3-MB
L3 cache, 4 threads (35W)
i5-540M, 2.53-GHz Intel® Core™ i5 dual-core processor, (Turbo up to 3.06 GHz),
3-MB L3 cache, 4 threads (35W)
594223-001
594756-001
594757-001
598210-001
598211-001
598212-001
598213-001
Display hinge cover (left and right) for use with HP EliteBook 8440w
Display bezel without webcam lens for HP EliteBook 8440w
Display bezel with webcam lens for HP EliteBook 8440w
14.0 HD AntiGlare LED SVA (1366x768) or use with HP EliteBook 8440w
14.0 HD AntiGlare LED SVA (1366x768) with webcam or use with HP EliteBook 8440w
14.0 HD+ AntiGlare LED SVA (1600x900) or use with HP EliteBook 8440w
14.0 HD+ AntiGlare LED SVA (1600x900) with webcam or use with HP EliteBook
8440w
598214-001
598859-001
598856-001
599092-001
CPU Mylar (processor support item)
1024-MB memory module (PC3-10600 DDR3 1333-MHz)
2048-MB memory module (PC3-10600 DDR3 1333-MHz)
4096-MB memory module (PC3-10600 DDR3 1333-MHz)
3–18
Maintenance and Service Guide
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
■
■
■
■
Flat-bladed screwdriver
Phillips P0
Phillips P1 screwdriver
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly and
assembly procedures.
As you remove each subassembly from the computer, place the subassembly (and all accompanying screws)
away from the work area to prevent damage.
✎
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the
plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Ä
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly
process. Improper cable placement can damage the computer.
Ä
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the
cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or
snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Maintenance and Service Guide
4–1
Removal and replacement procedures
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the computer,
Ä
damage to a drive, or loss of information, observe these precautions:
■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off
or in Hibernation, turn the computer on, and then shut it down through the operating system.
■ Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
■ Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure
that the optical drive tray is closed.
■ Handle drives on surfaces covered with at least one inch of shock-proof foam.
■ Avoid dropping drives from any height onto any surface.
■ After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
■ Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
■ Avoid exposing a drive to temperature extremes or liquids.
■ If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging
and label the package “FRAGILE.”
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the
degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD
contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle.
Or, the device may function normally for a while, and then degrade in the internal layers, reducing its life
expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal components, observe
Ä
these precautions:
■ Keep components in their electrostatic-safe containers until you are ready to install them.
■ Use nonmagnetic tools.
■ Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
■ Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
■
If you remove a component, place it in an electrostatic-safe container.
4–2
Maintenance and Service Guide
Removal and replacement procedures
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
ÄCAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
12,000 V
6,000 V
2,000 V
11,500 V
14,500 V
26,500 V
21,000 V
15,000 V
5,000 V
800 V
7,500 V
3,000 V
400 V
Walking across vinyl floor
Motions of bench worker
Removing DIPS from plastic tube
Removing DIPS from vinyl tray
Removing DIPS from Styrofoam
Removing bubble pack from PCB
Packing PCBs in foam-lined box
700 V
400 V
4,000 V
5,000 V
20,000 V
11,000 V
2,000 V
3,500 V
7,000 V
5,000 V
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
■
■
■
■
■
■
■
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
Keep ESD-sensitive parts in their containers until they arrive at static-free workstations.
Place items on a grounded surface before them from their containers.
Always be properly grounded when touching a component or assembly.
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized equipment
used for moving materials is wired to ground, and that proper materials are selected to avoid static charging.
When grounding is not possible, use an ionizer to dissipate electric charges.
Maintenance and Service Guide
4–3
Removal and replacement procedures
Workstation guidelines
Follow these workstation grounding guidelines:
■
■
Cover the workstation with approved static-shielding material.
Use a wrist strap connected to a properly grounded work surface, and use properly grounded tools and
equipment.
■
■
■
■
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam.
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items
only at static-free workstations.
■
■
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting or removing connectors or test equipment.
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
■
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm 10% resistance in the ground cords. To provide proper ground, wear a strap snugly
against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a
wrist strap.
■
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at
standing workstations and are compatible with most types of shoes or boots. On conductive floors or
dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the
operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
■
■
■
■
■
■
■
■
■
■
■
■
Antistatic tape
Antistatic smocks, aprons, and sleeve protectors
Conductive bins and other assembly or soldering aids
Nonconductive foam
Conductive tabletop workstations with ground cords of one megohm resistance
Static-dissipative tables or floor mats with hard ties to the ground
Field service kits
Static awareness labels
Material-handling packages
Nonconductive plastic bags, tubes, or boxes
Metal tote boxes
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
1,500 V
Antistatic plastic
Carbon-loaded plastic
Metallized laminate
Bags
Floor mats
Floor mats
7,500 V
5,000 V
4–4
Maintenance and Service Guide
Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 67 screws, in 9 different sizes, that must be removed, replaced, or loosened when servicing
the computer. Make special note of each screw size and location during removal and replacement.
Service tag
When ordering parts or requesting information, provide the computer serial number and model number provided on
Service tag color varies on select models.
✎
Item Field
Description
(1)
(2)
(3)
Product name
This is the product name affixed to the front of the computer.
This is an alphanumeric identifier that is unique to each product.
Serial
Product
This number provides specific information about the product’s hardware components. The
product number, or part number, helps a service technician determine what components and
parts are needed.
(4)
(5)
Warranty
Model
This number describes the duration of the warranty period for the computer.
This is the alphanumeric identifier used to locate documents, drivers, and support for the
computer.
Warranty and Model fields are excluded from the service tag on select models.
✎
Maintenance and Service Guide
4–5
Removal and replacement procedures
Computer feet
The computer feet are part of the base enclosure. The feet are included in the Rubber Kit, spare part number
594092-001. There are 5 rubber feet that attach to the base enclosure in the locations shown in the following
illustration.
4–6
Maintenance and Service Guide
Removal and replacement procedures
Battery
Description
Spare part number
489961-001
4 cell, 2.55-Ah (37-Wh) Li-ion battery
6 cell, 2.55-Ah (55-Wh) Li-ion battery
6 cell, 2.55-Ah (51-Wh) 1000-cycle battery
9 cell, 3.0-Ah (100-Wh) Li-ion battery
486296-001
593578-001
593579-001
Before removing the battery, follow these steps:
»
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch 1 to release the battery.
3. Remove the battery 2.
Install the battery by inserting it into the battery bay until you hear a click.
Maintenance and Service Guide
4–7
Removal and replacement procedures
SIM
The end user supplies the SIM, which stores the service-subscriber key to identify the subscriber on a wireless
wide-area network (WWAN). The SIM should be removed, stored in static-safe container, and replaced when
reassembling the computer.
✎
Before removing the SIM, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the SIM:
1. Push on the SIM 1 to release it from the SIM slot.
2. Remove the SIM 2 from the computer.
Install the SIM by inserting it into the SIM slot and pushing until you hear a click.
CAUTION: When inserting a SIM, position the card with the slanted corner as shown in the illustration. If a SIM is inserted
backwards or upside down, the battery may not snap into place properly and could damage the SIM and the SIM connector.
Ä
To prevent damage to the connectors, use minimal force when inserting a SIM.
4–8
Maintenance and Service Guide
Removal and replacement procedures
Hard drive
The hard drive spare part kit includes drive bracket, screws, and sponge material.
✎
Description
Spare part number
594044-001
250-GB 7200-rpm SATA hard drive
320-GB 7200-rpm SATA hard drive
500-GB 7200-rpm SATA hard drive
160-GB solid-state drive
594045-001
594046-001
594047-001
256-GB solid-state drive
594048-001
Before removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the hard drive:
1. Position the computer with the front toward you.
2. Loosen the 2 Phillips PM2.0×5.0 captive screws 1 that secure the hard drive cover to the computer.
3. Lift the left side 2 of the hard drive bay cover to detach it from the computer.
4. Remove the hard drive bay cover. The cover is included in the Plastics Kit, spare part number 594091-001.
Maintenance and Service Guide
4–9
Removal and replacement procedures
5. Loosen the Phillips PM2.5×10.0 captive screw 1 that secures the hard drive to the computer.
6. Grasp the Mylar tab 2 on the top of the hard drive, and then lift it up and to the right to disconnect the hard
drive from the hard drive connector on the system board.
7. Remove the hard drive 3 from the hard drive bay.
8. To replace the hard drive bracket, follow these steps:
a. Remove the 4 Phillips PM3.0×3.0 screws 1 that secure the hard drive bracket to the hard drive.
b. Lift the bracket straight up 2 to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
4–10
Maintenance and Service Guide
Removal and replacement procedures
WLAN module
Description
Spare part number
Broadcom BCM4312 802.11b/g WLAN module for use in Canada, the Cayman Islands, Guam,
Puerto Rico, the United States, and the U.S. Virgin Islands
504593-003
504593-004
Broadcom BCM4312 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Baha-
mas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina
Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Colombia,
Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Domin-
ica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Hon-
duras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia,
Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland, Portu-
gal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and
Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slove-
nia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis,
St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Tai-
wan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmeni-
stan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Intel a/g/n (2x2) for use in all countries and regions
Intel a/g/n (3x3) for use in all countries and regions
Intel a/b/g for use in Russia
572509-001
572511-001
572510-001
Before removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Maintenance and Service Guide
4–11
Removal and replacement procedures
Remove the WLAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in
Ä
the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module
and then receive a warning message, remove the module to restore computer functionality, and then contact technical support
through Help and Support.
1. Position the computer upside down, with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw 1 that secures the wireless module compartment cover to
the computer.
3. Lift the left side of the cover 2 to remove it from the computer.
The wireless module compartment cover is included in the Plastics Kit, spare part number 594091-001.
4–12
Maintenance and Service Guide
Removal and replacement procedures
4. Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module.
The antenna cables are labeled: 1 - black, 2 - white, and 3 - yellow. Connect the antenna cables to the
matching transmit/receive connector on the WLAN module.
✎
5. Remove the 2 Phillips PM2.5×4.0 screws 2 that secure the WLAN module to the computer.
6. Remove the WLAN module 3 by pulling it away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion of the WLAN module into
the WLAN module slot.
✎
Reverse this procedure to install the WLAN module.
Maintenance and Service Guide
4–13
Removal and replacement procedures
WWAN module
Description
Spare part number
574249-001
Ericsson F3607 SDG 900 HSPA minicard
Qualcomm Evolution-Data only (EVDO)/High-speed packet access (HSPA) minicard
531993-001
Before removing the WWAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the wireless module compartment cover.
1. Position the computer upside down, with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw 1 that secures the wireless module compartment cover to
the computer.
3. Lift the left side of the cover 2 to remove it from the computer.
The wireless module compartment cover is included in the Plastics Kit, spare part number 594091-001.
4–14
Maintenance and Service Guide
Removal and replacement procedures
Remove the WWAN module:
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the
computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore computer functionality, and then contact technical support through
Help and Support.
Ä
1. Position the computer upside down, with the front toward you.
2. Disconnect the WWAN antenna cables 1 from the terminals on the WWAN module.
The WWAN antenna cables are labeled: 5 - red, and 6 - blue. Connect the antenna cables to the matching
transmit/receive connector on the WWAN module.
✎
3. Remove the 2 Phillips PM2.5×4.0 screws 2 that secure the WWAN module to the computer. The WWAN
module tilts up with the screws removed.
4. Remove the WWAN module 3 by pulling it away from the slot at an angle.
WWAN modules are designed with a notch 4 to prevent incorrect insertion of the WWAN module into
the WWAN module slot.
✎
Reverse this procedure to install the WWAN module.
Maintenance and Service Guide
4–15
Removal and replacement procedures
Memory module
Description
Spare part number
599092-001
4096-MB memory module (PC3-10600 DDR3 1333-MHz)
2048-MB memory module (PC3-10600 DDR3 1333-MHz)
1024-MB memory module (PC3-10600 DDR3 1333-MHz)
598856-001
598859-001
Expansion memory module
Before removing the expansion memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the expansion memory module compartment cover.
1. Position the computer upside down, with the front toward you.
2. Loosen the Phillips PM2.0×5.0 captive screw 1 that secures the memory compartment cover to the computer.
3. Lift the left side of the cover 2 to remove it from the computer.
The memory module compartment cover is included in the plastics kit, spare part number 594091-001.
4–16
Maintenance and Service Guide
Removal and replacement procedures
Remove the expansion memory module:
The expansion memory module is accessed from the bottom of the computer; the primary memory module is
under the keyboard.
✎
1. Pull away the retention clips 1 on each side of the memory module to release the memory module. (The
memory module tilts up.)
CAUTION: The memory module is electrostatic sensitive. To prevent damage to the memory module, hold it by the card edge,
Ä
2. Grasp the edge of the memory module 2, and then remove it from the memory module slot.
Memory modules are designed with a notch 3 to prevent incorrect insertion into the memory module
slot.
✎
Reverse this procedure to install an expansion memory module.
Maintenance and Service Guide
4–17
Removal and replacement procedures
Primary memory module
Before removing the primary memory module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Open the keyboard:
1. Position the computer upside down, with the front toward you.
2. Loosen the 3 Phillips PM2.5×10.0 captive screws that secure the keyboard to the computer.
3. Turn the computer right-side up, with the front toward you.
4. Open the computer as far as possible.
5. Release the 4 keyboard latches.
4–18
Maintenance and Service Guide
Removal and replacement procedures
6. Lift the rear edge of the keyboard and slide the keyboard back until it rests on the switch cover and display.
Remove the primary memory module:
Primary memory is under the keyboard. Expansion memory is in the expansion memory compartment on the
bottom of the computer.
✎
1. Pull away the retention clips 1 on each side of the memory module to release the memory module. (The
memory module tilts up.)
CAUTION: The memory module is electrostatic sensitive. To prevent damage to the memory module, hold it by the card edge,
Ä
2. Grasp the edge of the memory module 2, and then remove it from the memory module slot.
Memory modules are designed with a notch 3 to prevent incorrect insertion into the memory module
slot.
✎
Reverse this procedure to install a primary memory module.
Maintenance and Service Guide
4–19
Removal and replacement procedures
Optical drive
The optical drive spare part kit includes an optical drive bezel, bracket, and rubber covers.
✎
Description
Spare part number
594041-001
Blu-ray R/RE DVD RW SuperMulti Drive
Blu-ray ROM with LightScribe DVD RW SuperMulti DL Drive
DVD RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
DVD-ROM Drive
594040-001
594043-001
594042-001
Before removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the optical drive:
1. Remove the Phillips PM2.5×10.0 screw 1 that secures the optical drive to the computer.
2. Insert a flat-bladed screwdriver or similar tool into the optical drive tab access 2, and then press the tab to the
left to release the optical drive from the computer.
3. Remove the optical drive 3 from the optical drive bay.
4–20
Maintenance and Service Guide
Removal and replacement procedures
4. If it is necessary to replace the optical drive bracket, follow these steps:
a. Position the optical drive with the rear toward you.
b. Remove the 3 Phillips PM2.0×4.0 screws 1 that secure the optical drive bracket to the optical drive.
c. Remove the optical drive bracket 2.
Reverse this procedure to reassemble and install an optical drive.
Maintenance and Service Guide
4–21
Removal and replacement procedures
Keyboard and switch cover
The switch cover spare part kit includes an LED board and cable.
✎
Description
Spare part number
594095-001
Switch cover for use with HP EliteBook 8440p
Switch cover for use with HP EliteBook 8440w
594096-001
The keyboard spare part kit includes a keyboard cable.
✎
Keyboard for use in country
or region:
Keyboard for use in country
Spare part number
594052-201
594052-261
594052-221
594052-081
594052-B31
594052-A41
594052-051
594052-121
594052-041
594052-DJ1
594052-211
594052-DD1
594052-BB1
594052-061
594052-291
594052-161
or region:
Spare part number
594052-091
594052-131
594052-251
594052-171
594052-231
594052-BA1
594052-AD1
594052-071
594052-B71
594052-BG1
594052-AB1
594052-281
594052-141
594052-031
594052-001
Brazil
Norway
Bulgaria
Czech Republic
Denmark
Europe
Portugal
Russia
Saudi Arabia
Slovakia
Europe A4
France
Slovenia
South Korea
Spain
French Canada
Germany
Greece
Sweden/Finland
Switzerland
Taiwan
Hungry
Iceland
Thailand
Israel
Turkey
Italy
United Kingdom
United States
Japan
Latin America
Before removing the keyboard and switch cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
4–22
Maintenance and Service Guide
Removal and replacement procedures
Remove the keyboard and switch cover:
1. Position the computer with the front toward you.
2. Remove the following:
❏ Two rubber screw covers 1 and 2 Torx T8 M2.5×6.0 screws 2 that secure the switch cover to the computer
❏ Three Phillips PM2.0×2.0 broadhead screws 3 that secure the switch cover to the computer in the battery
bay
Use the Phillips P0 screwdriver to remove the PM2.0×2.0 broadhead screws.
✎
❏ Three PM2.5×10.0 captive screws that secure the keyboard to the computer
3. Turn the computer right-side up, with the front toward you.
4. Open the computer as far as possible.
Maintenance and Service Guide
4–23
Removal and replacement procedures
5. Release the 4 keyboard latches 1.
6. Lift the rear edge 2 of the keyboard until it rests at an angle, and then turn the keyboard over until it rests on
the front of the top cover.
7. Release the zero insertion force (ZIF) connectors to which the pointing stick cable 1 and the keyboard cable 2
is attached, and then disconnect the cables from the system board.
8. Remove the keyboard.
4–24
Maintenance and Service Guide
Removal and replacement procedures
9. Release the ZIF connector to which the LED board cable 1 is attached, and then disconnect the LED board
cable from the system board.
10. Lift the back edge of the switch cover 2 and release it from the computer.
11. Remove the switch cover.
Reverse this procedure to install the keyboard and switch cover.
Maintenance and Service Guide
4–25
Removal and replacement procedures
Power button board
The power button board spare part kit includes the cable.
✎
Description
Spare part number
Power button board
594025-001
Before removing the power button board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the power button board:
1. Turn the switch cover over, with the front toward you.
2. Release the ZIF connector to which the power button board cable 1 connects to the LED board, and then
disconnect the cable from the LED board.
3. Remove the Phillips PM2.0×3.0 2 screw from the power button board.
4. Remove the power button board and cable 3.
Reverse this procedure to install the power button board.
4–26
Maintenance and Service Guide
Removal and replacement procedures
Display assembly
The display assembly spare part kit includes 3 transmit/receive WLAN antennas, 2 transmit/receive WWAN
antennas, the cables, and the nameplate.
✎
Description
Spare part number
14.0-in LED display assembly for use with WLAN and WWAN (includes 3 transmit/receive WLAN antennas, 2 transmit/receive
WWAN antennas, and the cables):
■ 14.0-in HD Antiglare LED SVA (1366 x 768 resolution) for use with HP EliteBook 8440p
■ 14.0-in HD Antiglare LED SVA (1366 x 768) with webcam for use with HP EliteBook 8440p
■ 14.0-in HD+ Antiglare LED SVA (1600 x 900) for use with HP EliteBook 8440p
■ 14.0-in HD+ Antiglare LED SVA (1600 x 900) with webcam for use with HP EliteBook 8440p
■ 14.0-in HD AntiGlare LED SVA (1366 x 768) for use with HP EliteBook 8440w
■ 14.0-in HD AntiGlare LED SVA (1366 x 768) with webcam for use with HP EliteBook 8440w
■ 14.0-in HD+ AntiGlare LED SVA (1600 x 900) for use with HP EliteBook 8440w
■ 14.0-in HD+ AntiGlare LED SVA (1600 x 900) with webcam for use with HP EliteBook 8440w
Display assembly subcomponents
594087-001
594088-001
594089-001
594090-001
598210-001
598211-001
598212-001
598213-001
■ Display cable
594037-001
594029-001
594039-001
594038-001
594223-001
■ Ambient light sensor/connector board
■ Display hinge/bracket
■ Display hinge covers for use with HP EliteBook 8440p
■ Display hinge covers for use with HP EliteBook 8440w
Display bezel
■ Display bezel without webcam lens for HP EliteBook 8440p
■ Display bezel with webcam lens for HP EliteBook 8440p
■ Display bezel without webcam lens for HP EliteBook 8440w
■ Display bezel with webcam lens for HP EliteBook 8440w
Display back cover
594035-001
594036-001
594756-001
594757-001
The display back cover includes the dual-array microphone, wireless antennas, and
associated cables, and on models that use a webcam, the webcam and webcam cable.
✎
■ Display back cover with webcam for HP EliteBook 8440p
■ Display back cover with webcam for HP EliteBook 8440w
■ Display back cover without webcam for HP EliteBook 8440p
■ Display back cover without webcam for HP EliteBook 8440w
■ Display back cover without webcam for HP EliteBook 8440w
594031-001
594032-001
594033-001
594034-001
577188-001
Maintenance and Service Guide
4–27
Removal and replacement procedures
Before removing the display assembly, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
4–28
Maintenance and Service Guide
Removal and replacement procedures
Remove the display assembly:
1. Turn the computer right side up, with the front toward you.
2. Open the computer.
3. Remove the wireless antenna cables 1 from the opening, clips, and routing channel 2 on the top cover.
When installing the display assembly, be sure to route the wireless antenna cables through the cable channel. The
wireless antenna cables have exposed shields that contact a grounding pad on the top cover. Failure to make proper
contact can result in degraded performance.
✎
4. Disconnect to microphone cable 1 from the system board.
5. Remove the microphone cable from the clips and channel 2 built into the top cover.
6. Disconnect the display cable 3 from the system board, and then remove the display cable.
Maintenance and Service Guide
4–29
Removal and replacement procedures
CAUTION: Support the display assembly when removing the following screws. Failure to support the display
assembly can result in damage to the display assembly and other computer components.
Ä
7. Remove the two rubber screw covers 1 and two Torx T8M2.5×6.0 screws 2 that secure the display assembly
to the back of the computer.
8. Remove the two Torx T8M2.5×6.0 screws 3 that secure the display assembly to the bottom of the computer.
9. Turn the computer right-side up and open the display.
10. Remove the two Torx T8M2.5×6.0 screws 1 that secure the display assembly hinges to the base enclosure.
11. Lift the display assembly 2 straight up and remove it.
4–30
Maintenance and Service Guide
Removal and replacement procedures
12. If it is necessary to replace the display bezel or any of the display assembly subcomponents, follow these steps:
a. Remove the four rubber screw covers 1 and the four Torx T8M2.5×6.0 screws 2 that secure the display
bezel to the display assembly.
b. Flex the top inside edge 1, the left and right inside edges 2, and the bottom inside edge 3 of the display
bezel until the bezel disengages from the display enclosure.
c. Remove the display bezel 4. The display bezel is available using the following spare part numbers:
◆
◆
◆
◆
594036-001 - Display bezel for use on HP EliteBook 8440p equipped with a webcam
594035-001 - Display bezel for use on HP EliteBook 8440p not equipped with webcam
594757-001 - Display bezel for use on HP EliteBook 8440w equipped with a webcam
594756-001 - Display bezel for use on HP EliteBook 8440w not equipped with webcam
Maintenance and Service Guide
4–31
Removal and replacement procedures
13. If it is necessary to replace the display hinges:
a. Remove the four Phillips PM2.5×5.0 screws that secure the display panel to the display back cover.
b. Remove the display panel cable 1 from the ambient light sensor/connector board and clips 2 in the display
back cover.
c. Remove the display panel 3.
4–32
Maintenance and Service Guide
Removal and replacement procedures
d. Remove 6 Phillips PM2.5×3.0 screws 1 that secure the display hinges to the display panel. The display
hinge set is available as spare part number 594039-001.
e. Remove the display hinges 2.
14. If it is necessary to replace the display hinge covers:
a. Loosen the PM2.5×3.0 screws 1 that hold the display hinge covers in place.
b. Slide the display hinge covers off 2 the display hinges.
Maintenance and Service Guide
4–33
Removal and replacement procedures
15. If it is necessary to replace the display cable:
a. Turn the display panel upside down, with the top edge toward you.
b. Fold back the adhesive strip 1 that covers the display cable connector.
c. Release the support bar 2 that secures the display cable to the display panel.
d. Disconnect the display cable 3 from display panel connector. The display cable is available using spare part
number 594037-001.
16. If necessary to replace the webcam module and cables, the dual-array microphone and microphone cable, or
the wireless antennas and cables, replace the display back cover using the following part numbers:
❏ 594031-001 - Display back cover for use on EliteBook 8440p equipped with a webcam
❏ 594032-001 - Display back cover for use on EliteBook 8440w equipped with a webcam
❏ 594033-001 - Display back cover for use on EliteBook 8440p not equipped with a webcam
❏ 594034-001 - Display back cover for use on EliteBook 8440w not equipped with a webcam
The back cover spares that come with or without the webcam include the WLAN and WWAN antenna
✎
cables 1, WLAN and WWAN antenna 2, webcam cable 3 (with webcam), keyboard light and cable 4,
and the dual-array microphone and cable 5.
Reverse this procedure to install the display assembly.
4–34
Maintenance and Service Guide
Removal and replacement procedures
Fan and heat sink
The fan and heat sink spare part kits include replacement thermal material.
✎
Description
Spare part number
Fan
594049-001
Heat sink for use on computer models equipped with a graphics subsystem using discrete memory 594050-001
Heat sink for use on computer models equipped with a graphics subsystem using UMA memory 594051-001
To properly ventilate the computer, allow at least 7.6 cm (3 in) of clearance on the left side of the computer. The
computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to
turn on when high temperature conditions exist. These conditions are affected by high external temperatures,
system power consumption, power management/battery conservation configurations, battery fast charging, and
software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the
computer.
✎
Before removing the fan and heat sink, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Maintenance and Service Guide
4–35
Removal and replacement procedures
Remove the fan:
1. Disconnect the fan cable 1 from the system board.
2. Remove the Mylar strip 2 taped between the fan and the heat sink.
3. Remove the two Torx T8M2.5×6.0 screws 3 that secure the fan to the system board.
4. Lift straight up to remove the fan assembly 4.
4–36
Maintenance and Service Guide
Removal and replacement procedures
Remove the heat sink:
1. Following the 1, 2, 3, 4 sequence stamped into the heat sink, loosen the 4 Phillips PM2.5×10.0 spring-loaded
captive screws 1 that secure the heat sink to the system board.
2. Pull the heat sink up 2 and away 3 from the ventilation grill. If necessary, move the heat sink side-to-side to
release the heat sink from the thermal material.
The first illustration below shows the heat sink on computer models that use the discrete graphics subsystem. The
second illustration shows the heat sink on computer models that use the UMA graphics subsystem.
✎
3. Remove the heat sink assembly.
Maintenance and Service Guide
4–37
Removal and replacement procedures
Replace the thermal material:
The thermal material must be cleaned from the surfaces of the heat sink and the system board each time the heat
sink is removed. Replacement thermal material is included with fan, heat sink, and heat shield spare parts.
■
■
■
Thermal paste is used between the processor 1 and the heat sink section 2 that services it.
Thermal pads are used between the system board capacitors 3 and the heat sink section 4 that services it.
Thermal pads are used on the graphics subsystem memory module 5 and the heat sink section 6 that
services it.
The first illustration shows thermal material locations on computer models that use the discrete graphics
subsystem. The second illustration shows the thermal material locations on computer models that use the UMA
graphics subsystem.
✎
Reverse this procedure to install the fan and heat sink.
4–38
Maintenance and Service Guide
Removal and replacement procedures
RTC battery
Description
Spare part number
RTC battery
581075-001
Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
Remove the RTC battery:
1. Disconnect the RTC battery cable 1 from the system board.
2. Detach the RTC battery 2 from the top cover. The RTC battery is attached to the top cover with
double-sided tape.
Reverse this procedure to install the RTC battery.
Maintenance and Service Guide
4–39
Removal and replacement procedures
Processor
The processor spare part kit includes replacement thermal material.
✎
Description
Spare part number
Intel® Core™ i5 dual-core processors (3-MB L3 cache, 4 threads, 35W):
■ i5-520M, 2.4-GHz processor (Turbo up to 2.93 GHz)
594187-001
594188-001
■ i5-540M, 2.53-GHz processor (Turbo up to 3.06 GHz)
Intel® Core™ i7 quad-core, processor (6-MB L3 cache, 8 threads, 45W):
■ i7-620M, 2.66-GHz processor (Turbo up to 3.33GHz)
587259-001
Intel® Core™ i7 quad-core, processors:
■ i7-720QM, 1.6-GHz processor (Turbo up to 2.8 GHz, 6-MB L3 cache, 8 threads, 45W)
■ i7-820QM, 1.73-GHz processor (Turbo up to 3.06 GHz, 8-MB L3 cache, 8 threads, 45W)
586170-001
583053-001
Before removing the processor, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
4–40
Maintenance and Service Guide
Removal and replacement procedures
Remove the processor:
1. Use a flat-bladed screwdriver to turn the processor locking screw 1 one-half turn counterclockwise, until you
hear a click.
Unlocking and locking directions are embossed on the processor socket.
✎
2. Lift the processor 2 straight up and remove it.
When you install the processor, align the gold triangle 3 etched on top of the processor with the triangle embossed
on the processor socket 4.
✎
Clean and replace any thermal material, and then reverse this procedure to install the processor.
Maintenance and Service Guide
4–41
Removal and replacement procedures
Top cover
The top cover spare part kit includes TouchPad assembly, cable, and bracket; the ESD boards; the smart card
reader; and on some models, a fingerprint reader and bracket.
✎
Description
Spare part number
594098-001
Top cover with integrated smart card reader and fingerprint reader for use on HP EliteBook 8440p
Top cover with integrated smart card reader and fingerprint reader for use on HP EliteBook 8440w
594099-001
Top cover with integrated smart card reader without fingerprint reader for use on HP EliteBook
8440w (Plastics Kit includes fingerprint reader plug)
594100-001
Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the top cover:
1. Turn the computer upside down, with the front toward you.
2. Remove the 3 rubber screw covers 1, the 6 Torx T8M2.5×6.0 screws 2, and the 2 Phillips PM2.5×3.0
screws 3 in the hard drive bay that secure the top cover to the base enclosure.
4–42
Maintenance and Service Guide
Removal and replacement procedures
3. Turn the computer right-side up, with the front toward you.
4. Disconnect the touch pad cable 1, the fingerprint reader cable 2, and the ExpressCard reader cable 3 from the
system board.
5. Remove the three Torx T8M2.5×6.0 screws that secure the top cover to the base enclosure.
6. Lift the rear edge 1 of the top cover until it detaches from the base enclosure.
7. Remove the top cover 2 by lifting it straight up.
Reverse this procedure to install the top cover.
Maintenance and Service Guide
4–43
Removal and replacement procedures
Audio/ExpressCard board
Description
Spare part number
Audio/ExpressCard board
594024-001
Before removing the Audio/ExpressCard board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the Audio/ExpressCard board:
1. Release the speaker cable from the connector 1 on the Audio/ExpressCard board.
2. Remove the two Phillips PM2.0×4.0×7.0 broadhead screws 2 and the Phillips PM2.0×4.0 3 screw from the
Audio/ExpressCard board.
3. Lift the right edge of the Audio/ExpressCard board 4 up.
4. Slide the Audio/ExpressCard board 5 to the right to clear the audio connectors from the base enclosure.
5. Remove the Audio/ExpressCard board.
Reverse this procedure to install the Audio/ExpressCard board.
4–44
Maintenance and Service Guide
Removal and replacement procedures
Speakers
Description
Spare part number
Speakers (include cables)
594094-001
Before removing the speakers, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the speakers:
1. Remove the Phillips PM2.5×4.0 screw 1 that secures the left speaker to the base enclosure.
2. Lift the left speaker straight up 2 to remove the left speaker.
3. Lift the right speaker up and to the left 3 to remove the right speaker.
Reverse this procedure to install the speakers.
Maintenance and Service Guide
4–45
Removal and replacement procedures
Bluetooth module and cable
The Bluetooth module spare part does not include the Bluetooth module cable. The Bluetooth module cable is
included in the Cable Kit, spare part number 594030-001.
✎
Description
Spare part number
Bluetooth module
594030-001
Before removing the Bluetooth module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
4–46
Maintenance and Service Guide
Removal and replacement procedures
Remove the Bluetooth module and cable:
1. Loosen the Phillips PM2.0×4.0 captive screw 1.
2. Swing the Bluetooth compartment cover open 2 to the right.
3. Shift the Bluetooth module right 1 and lift it up 2 until it clears the clips built into the Bluetooth module
compartment cover.
4. Remove the Bluetooth module 3 from the Bluetooth module compartment cover.
5. Disconnect the Bluetooth module cable 4 from the Bluetooth module.
6. Remove the Bluetooth module.
Maintenance and Service Guide
4–47
Removal and replacement procedures
7. If it is necessary to replace the Bluetooth module cable:
The Bluetooth module cable is included in the Cable Kit, spare part number 594030-001.
✎
a. Disconnect the Bluetooth module cable 1 from the system board.
b. Remove the Bluetooth module cable 2 from the cable routing channel in the base enclosure.
Reverse this procedure to install the Bluetooth module and cable.
4–48
Maintenance and Service Guide
Removal and replacement procedures
Modem module
The modem module cable is included in the Cable kit, spare part number 594030-001.
✎
Description
Spare part number
High-speed 56k modem for use in all countries and regions except Australia and New Zealand
High-speed 56k modem for use only in Australia and New Zealand
510099-001
510099-011
Before removing the modem module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the modem module:
1. Remove the 2 Phillips PM2.0×4.0 screws 1 that secure the modem module to the system board.
2. Lift the modem module 2 away from the system board.
3. Disconnect the modem module cable 3 to remove the modem module.
Reverse this procedure to install the modem module.
Maintenance and Service Guide
4–49
Removal and replacement procedures
System board
The system board spare part kit includes replacement thermal material.
✎
Description
Spare part number
594026-001
System board for use with HP EliteBook 8440p discrete graphics subsystem
System board for use with HP EliteBook 8440w discrete graphics subsystem
System board for use with HP EliteBook 8440p UMA graphics subsystem
594027-001
594028-001
Before removing the system board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
When replacing the system board, be sure that the following additional components are removed from the defective
system board and installed on the replacement system board:
■
■
■
■
■
■
■
■
4–50
Maintenance and Service Guide
Removal and replacement procedures
Remove the system board:
1. Remove the Phillips PM2.0×4.0 screw 1 that secures the thermal heat shield to the base enclosure and
compresses the thermal material to the platform controller hub (PCH) chip on the system board.
2. Lift the thermal shield straight up 2 to remove it.
The thermal shield and system board spare parts include replacement thermal material. Clean and install new
thermal material when replacing the thermal shield.
✎
3. Remove the 2 Phillips PM2.5×4.0 screws 1 that secure the system board to the base enclosure.
4. Use the optical drive connector 2 to lift the system board away from the base enclosure.
5. Remove the system board 3 by lifting it to the right at an angle until the connectors clear the base enclosure.
Reverse this procedure to install the system board.
Maintenance and Service Guide
4–51
Removal and replacement procedures
Modem module cable
The modem module cable is included in the Cable kit, spare part number 594030-001.
✎
Before removing the modem module cable, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
5. Remove the following components:
Remove the modem module cable:
1. Release the RJ-11 connector 1 from the clip built into the base enclosure.
2. Remove the modem module cable 2 from the clips and the cable channel 3 built into the base enclosure.
Reverse this procedure to install the modem module cable.
4–52
Maintenance and Service Guide
5
Computer Setup
Computer Setup in Windows 7
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and
make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
Maintenance and Service Guide
5–1
Computer Setup
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values configured at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
5–2
Maintenance and Service Guide
Computer Setup
File menu
Select
To do this
System Information
■ View identification information for the computer and
the batteries in the system.
■ View specification information for the processor, cache and
memory size, system ROM, video revision, and keyboard
controller version.
Set System Date and Time
System Diagnostics
Set or change the date and time on the computer.
Displays the following information:
■ System Information
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, cache and
memory size, system ROM, video revision, and
keyboard controller version.
■ Start-up Test—Verifies the system components needed for
starting the computer.
■ Run-In Test—Runs a comprehensive check on system
memory.
■ Hard Disk Test—Runs a comprehensive self-test on any
hard drive in the system.
■ Memory Test—Runs a comprehensive test on any memory
installed in the computer.
■ Battery Test—Runs a comprehensive test on any batteries
installed in the computer.
■ Error Log—Displays a log file if any errors have occurred.
Restore Defaults
Replace the configuration settings in Computer Setup with
the original factory settings. (Hard drive mode, password
settings, and security settings are not changed when you
restore the factory settings.
Reset BIOS security to factory default
Ignore Changes and Exit
Restore the BIOS security settings to the factory default.
Cancel any changes entered during the current session.
Then exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session. Then
exit and restart the computer. Your changes go into effect
when the computer restarts.
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Administrator Tools
Setup BIOS Administrator Password
User Management (requires a BIOS administrator password)
Create New BIOS User Account
Set up a BIOS administrator password.
■ Select from a list of BIOS users.
■ Select from a list of ProtectTools users.
(Continued)
Maintenance and Service Guide
5–3
Computer Setup
Select
To do this
Security menu (continued)
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Enable/disable HP SpareKey enrollment (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
User Tools
Change Password
HP SpareKey Enrollment
Enter, change, or delete a BIOS administrator password.
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
Anti Theft
AT-P
Enable/disable Anti-Theft Protection.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting) the
computer.
Automatic DriveLock
Enable/disable Automatic DriveLock support.
TPM Embedded Security
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change this
setting.
✎
Disk Sanitizer
System IDs
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
Ä
Enter a user-defined computer asset tracking number and
ownership tag.
5–4
Maintenance and Service Guide
Computer Setup
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Set the MultiBook Express Boot Popup delay in seconds.
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled by
default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) Boot Mode (disabled by default).
■ Set the Legacy Boot Order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows® operating system is not running
❐ Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a USB
port to the computer
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced Parallel
Port).
■ Enable/disable fan always on while connected to an AC
outlet (enabled by default).
■ Enable/disable Data Execution Prevention (select models
only). When enabled, the processor can disable some
virus code execution, which helps to improve computer
security (disabled by default).
■ Set the SATA (Serial Advanced Technology Attachment)
device mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of these options varies by computer model.
✎
■ Enable/disable secondary battery fast charge (enabled by
default).
■ Enable/disable HP QuickLook (enabled by default).
■ Enable/disable Preboot Authentication on HP QuickLook
Boot (enabled by default).
■ Enable/disable HP QuickWeb (enabled by default).
■ Enable/disable HP QuickWeb Write Protect (disabled by
default).
■ Enable/disable Virtualization Technology (select models
only; disabled by default).
(Continued)
Maintenance and Service Guide
5–5
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
■ Enable/disable Multi Core CPU (enabled by default).
■ Enable/disable Intel HT Technology (enabled by default).
■ Enable/disable Wake on USB (enabled by default).
■ Enable/disable Num lock state at boot (disabled by
default).
Built-In Device Options
■ Enable/disable the wireless button state (enabled by
default).
■ Enable/disable embedded WLAN device radio (select
models only; enabled by default).
■ Enable/disable the embedded Bluetooth® device radio
(enabled by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network
❐ Follow Boot Order
■ Enable/disable the Ambient Light Sensor.
■ Enable/disable the Notebook Upgrade Bay device (enabled
by default).
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable the integrated camera (enabled by default).
■ Enable/disable the Power Monitor Circuit (enabled by
default).
■ Enable/disable the audio device (enabled by default).
■ Enable/disable a modem device (enabled by default).
■ Enable/disable the microphone (enabled by default).
■ Enable/disable the internal speakers (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay
Ä
devices and ExpressCard devices on the advanced
port replicator.
■ Enable/disable the 1394 port.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the Smart Card slot.
■ Enable/disable the eSATA port
(Continued)
5–6
Maintenance and Service Guide
Computer Setup
Select
To do this
System Configuration menu (continued)
AMT Options
■ Enable/disable Firmware Verbosity.
■ Enable/disable AMT Setup Prompt (Ctrl-P).
■ Enable/disable USB Key Provisioning Support.
■ Enable/disable Unconfigure AMT on next boot.
■ Select Terminal Emulation Mode.
❐ ANSI
❐ VT100
■ Enable/disable Firmware Progress Event Support.
■ Enable/disable Initiate Intel CIRA.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
Maintenance and Service Guide
5–7
Computer Setup
Computer Setup in Windows Vista
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
✎
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate
and make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
5–8
Maintenance and Service Guide
Computer Setup
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values configured at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
File menu
Select
To do this
System Information
■ View identification information for the computer and the
batteries in the system.
■ View specification information for the processor, cache and
memory size, system ROM, video revision, and keyboard
controller version.
Set System Data and Time
System Diagnostics
■ Set or change the date and time on the computer.
■ System Information
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, cache and
memory size, system ROM, video revision, and
keyboard controller version.
■ Start-up Test—Verifies the system components needed for
starting the computer.
■ Run-In Test—Runs a comprehensive check on system
memory.
■ Hard Disk Test—Runs a comprehensive self-test on any
hard drive in the system.
(Continued)
Maintenance and Service Guide
5–9
Computer Setup
Select
To do this
File menu (continued)
System Diagnostics (continued)
■ Memory Test—Runs a comprehensive test on any memory
installed in the computer.
■ Battery Test—Runs a comprehensive test on any batteries
installed in the computer.
■ Error Log—Displays a log file if any errors have occurred.
Restore Defaults
Replace the configuration settings in Computer Setup with the
original factory settings. (Hard drive mode, password settings,
and security settings are not changed when you restore the
factory settings.)
Reset BIOS security to factory default
Ignore Changes and Exit
Restore the BIOS security settings to the factory default.
Cancel any changes entered during the current session. Then
exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session. Then
exit and restart the computer. Your changes go into effect
when the computer restarts.
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Administrator Tools
Setup BIOS Administrator Password
User Management (requires a BIOS administrator password)
Create New BIOS User Account
Set up a BIOS administrator password.
■ Select from a list of BIOS users.
■ Select from a list of ProtectTools users.
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Enable/disable HP SpareKey enrollment (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
User Tools
Change Password
HP SpareKey Enrollment
Enter, change, or delete a BIOS administrator password.
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
Anti Theft
AT-P
Enable/disable Anti-Theft Protection.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting) the
computer.
(Continued)
5–10
Maintenance and Service Guide
Computer Setup
Select
To do this
Security menu (continued)
Automatic DriveLock
TPM Embedded Security
Enable/disable Automatic DriveLock support.
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change this
setting.
✎
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
Ä
System IDs
Enter a user-defined computer asset tracking number and
ownership tag.
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Set the MultiBook Express Boot Popup delay in seconds.
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled by
default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) Boot Mode (disabled by default).
■ Set the Legacy Boot Order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows® operating system is not running
❐ Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a USB
port to the computer
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced Parallel
Port).
■ Enable/disable fan always on while connected to an AC
outlet (enabled by default).
(Continued)
Maintenance and Service Guide
5–11
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable Data Execution Prevention (select models
only). When enabled, the processor can disable some virus
code execution, which helps to improve computer security
(disabled by default).
■ Set the SATA (Serial Advanced Technology Attachment)
device mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of these options varies by computer model.
✎
■ Enable/disable secondary battery fast charge (enabled by
default).
■ Enable/disable HP QuickLook (enabled by default).
■ Enable/disable Preboot Authentication on HP QuickLook
Boot (enabled by default).
■ Enable/disable HP QuickWeb (enabled by default).
■ Enable/disable HP QuickWeb Write Protect (disabled by
default).
■ Enable/disable Virtualization Technology (select models
only; disabled by default).
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
■ Enable/disable Multi Core CPU (enabled by default).
■ Enable/disable Intel HT Technology (enabled by default).
■ Enable/disable Wake on USB (enabled by default).
■ Enable/disable Num lock state at boot (disabled by default).
Built-In Device Options
■ Enable/disable the wireless button state (enabled by
default).
■ Enable/disable embedded WLAN device radio (select
models only; enabled by default).
■ Enable/disable the embedded Bluetooth® device radio
(enabled by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network
❐ Follow Boot Order
■ Enable/disable the Ambient Light Sensor.
■ Enable/disable the Notebook Upgrade Bay device (enabled
by default).
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable the integrated camera (enabled by default).
■ Enable/disable the Power Monitor Circuit (enabled by
default).
■ Enable/disable the audio device (enabled by default).
(Continued)
5–12
Maintenance and Service Guide
Computer Setup
Select
To do this
System Configuration menu (continued)
Built-In Device Options (continued)
■ Enable/disable a modem device (enabled by default).
■ Enable/disable the microphone (enabled by default).
■ Enable/disable the internal speakers (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay
Ä
devices and ExpressCard devices on the advanced
port replicator.
■ Enable/disable the 1394 port.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the Smart Card slot.
■ Enable/disable the eSATA port
AMT Options
■ Enable/disable Firmware Verbosity.
■ Enable/disable AMT Setup Prompt (Ctrl-P).
■ Enable/disable USB Key Provisioning Support.
■ Enable/disable Unconfigure AMT on next boot.
■ Select Terminal Emulation Mode.
❐ ANSI
❐ VT100
■ Enable/disable Firmware Progress Event Support.
■ Enable/disable Initiate Intel CIRA.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
Maintenance and Service Guide
5–13
Computer Setup
Computer Setup in Windows XP
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not
working or will not load.
Some of the Computer Setup menu items listed in this guide may not be supported by your computer.
✎
An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy
support is enabled.
✎
To start Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System
Configuration menus.
To navigate and select in Computer Setup, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
❏ To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a
pointing device to click the item.
❏ To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the screen, or use
the up arrow key or the down arrow key.
❏ To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the
on-screen instructions.
You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to
navigate and make selections in Computer Setup.
✎
2. Press f10 to enter BIOS Setup.
3. Select the File, Security, Diagnostics, or System Configuration menu.
To exit Computer Setup menus, choose one of the following methods:
■
To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.
– or –
■
To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.
5–14
Maintenance and Service Guide
Computer Setup
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
Restoring defaults will not change the hard drive mode.
✎
To return all settings in Computer Setup to the values configured at the factory, follow these steps:
1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is
displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Use a pointing device or the arrow keys to select File > Restore Defaults.
4. Follow the on-screen instructions.
5. To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the
on-screen instructions.
– or –
Use the arrow keys to select File > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Your password settings and security settings are not changed when you restore the factory settings.
✎
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
Some of the Computer Setup menu items listed in this chapter may not be supported by your computer.
✎
File menu
Select
To do this
System Information
■ View identification information for the computer and the
batteries in the system.
■ View specification information for the processor, cache and
memory size, system ROM, video revision, and keyboard
controller version.
Set System Data and Time
System Diagnostics
■ Set or change the date and time on the computer.
■ System Information
❐ Identification information for the computer and the
batteries in the system.
❐ Specification information for the processor, cache and
memory size, system ROM, video revision, and
keyboard controller version.
■ Start-up Test—Verifies the system components needed for
starting the computer.
■ Run-In Test—Runs a comprehensive check on system
memory.
■ Hard Disk Test—Runs a comprehensive self-test on any
hard drive in the system.
(Continued)
Maintenance and Service Guide
5–15
Computer Setup
Select
To do this
File menu (continued)
System Diagnostics (continued)
■ Memory Test—Runs a comprehensive test on any memory
installed in the computer.
■ Battery Test—Runs a comprehensive test on any batteries
installed in the computer.
■ Error Log—Displays a log file if any errors have occurred.
Restore Defaults
Replace the configuration settings in Computer Setup with
the original factory settings. (Hard drive mode, password
settings, and security settings are not changed when you
restore the factory settings.)
Reset BIOS security to factory default
Ignore Changes and Exit
Restore the BIOS security settings to the factory default.
Cancel any changes entered during the current session. Then
exit and restart the computer.
Save Changes and Exit
Save any changes entered during the current session. Then
exit and restart the computer. Your changes go into effect
when the computer restarts.
Security menu
Some of the menu items listed in this section may not be supported by your computer.
✎
Select
To do this
Administrator Tools
Setup BIOS Administrator Password
User Management (requires a BIOS administrator password)
Create New BIOS User Account
Set up a BIOS administrator password.
■ Select from a list of BIOS users.
■ Select from a list of ProtectTools users.
Password Policy (requires a BIOS administrator password)
HP SpareKey
Revise password policy criteria.
Enable/disable HP SpareKey (enabled by default).
Enable/disable HP SpareKey enrollment (enabled by default).
Always Prompt for HP SpareKey Enrollment
Fingerprint Reset on Reboot (If Present)
Reset/clear the fingerprint reader ownership (select models
only; disabled by default).
User Tools
Change Password
HP SpareKey Enrollment
Enter, change, or delete a BIOS administrator password.
Enroll or reset HP SpareKey, which is a set of security
questions and answers used if you forget your password.
Anti Theft
AT-P
Enable/disable Anti-Theft Protection.
DriveLock Passwords
■ Enable/disable DriveLock on any computer hard drive
(enabled by default).
■ Change a DriveLock user password or master password.
DriveLock settings are accessible only when you enter
✎
Computer Setup by turning on (not restarting) the
computer.
(Continued)
5–16
Maintenance and Service Guide
Computer Setup
Select
To do this
Security menu (continued)
Automatic DriveLock
TPM Embedded Security
Enable/disable Automatic DriveLock support.
Enable/disable support for Trusted Platform Module (TPM)
Embedded Security, which protects the computer from
unauthorized access to owner functions available in
Embedded Security for ProtectTools. For more information,
refer to the ProtectTools software Help.
You must have a setup password to change this
setting.
✎
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary
hard drive or the drive in the upgrade bay.
If you run Disk Sanitizer, the data on the selected drive
is destroyed permanently.
Ä
System IDs
Enter a user-defined computer asset tracking number and
ownership tag.
System Configuration menu
Some of the listed System Configuration options may not be supported by your computer.
✎
Select
To do this
Language
Boot Options
Change the Computer Setup language.
■ Set a Startup Menu delay (in seconds).
■ Set the MultiBook Express Boot Popup delay in seconds.
■ Enable/disable Custom Logo (disabled by default).
■ Enable/disable Display Diagnostic URL (enabled by
default).
■ Enable/disable CD-ROM boot (enabled by default).
■ Enable/disable SD Card boot (enabled by default).
■ Enable/disable floppy boot (enabled by default).
■ Enable/disable PXE Internal NIC boot (enabled by default).
■ Enable/Disable Unified Extensible Firmware Interface
(UEFI) Boot Mode (disabled by default).
■ Set the Legacy Boot Order.
Device Configurations
■ Enable/disable USB legacy support (enabled by default).
When enabled, USB legacy support allows the following:
❐ Use of a USB keyboard in Computer Setup even when a
Windows® operating system is not running
❐ Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a USB
port to the computer
■ Select a parallel port mode: ECP (Enhanced Capabilities
Port), standard, bidirectional, or EPP (Enhanced Parallel
Port).
■ Enable/disable fan always on while connected to an AC
outlet (enabled by default).
(Continued)
Maintenance and Service Guide
5–17
Computer Setup
Select
To do this
System Configuration menu (continued)
Device Configurations (continued)
■ Enable/disable Data Execution Prevention (select models
only). When enabled, the processor can disable some virus
code execution, which helps to improve computer security
(disabled by default).
■ Set the SATA (Serial Advanced Technology Attachment)
device mode. The following options are available:
❐ AHCI (Advanced Host Controller Interface)
❐ IDE (Integrated Drive Electronics)
❐ RAID (select models only)
Availability of these options varies by computer model.
✎
■ Enable/disable secondary battery fast charge (enabled by
default).
■ Enable/disable HP QuickLook (enabled by default).
■ Enable/disable Preboot Authentication on HP QuickLook
Boot (enabled by default).
■ Enable/disable HP QuickWeb (enabled by default).
■ Enable/disable HP QuickWeb Write Protect (disabled by
default).
❐ Enable/disable Virtualization Technology (select models
only; disabled by default).
■ Enable/disable TXT (Intel Trusted Execution Technology)
(select models only; disabled by default).
■ Enable/disable Multi Core CPU (enabled by default).
■ Enable/disable Intel HT Technology (enabled by default).
■ Enable/disable Wake on USB (enabled by default).
■ Enable/disable Num lock state at boot (disabled by default).
Built-In Device Options
■ Enable/disable the wireless button state (enabled by
default).
■ Enable/disable embedded WLAN device radio (select
models only; enabled by default).
■ Enable/disable the embedded Bluetooth® device radio
(enabled by default).
■ Enable/disable the Network Interface Controller (LAN)
(enabled by default).
■ Enable/disable LAN/WLAN switching (disabled by default).
■ Set the wake on LAN state. Options include the following:
❐ Disabled
❐ Boot to Network
❐ Follow Boot Order
■ Enable/disable the Ambient Light Sensor.
■ Enable/disable the Notebook Upgrade Bay device (enabled
by default).
■ Enable/disable the fingerprint device (enabled by default).
■ Enable/disable the integrated camera (enabled by default).
■ Enable/disable the Power Monitor Circuit (enabled by
default).
■ Enable/disable the audio device (enabled by default).
■ Enable/disable a modem device (enabled by default).
(Continued)
5–18
Maintenance and Service Guide
Computer Setup
Select
To do this
System Configuration menu (continued)
Built-In Device Options (continued)
■ Enable/disable the microphone (enabled by default).
■ Enable/disable the internal speakers (enabled by default).
Port Options (all are enabled by default)
All port options are enabled by default.
✎
■ Enable/disable the serial port.
■ Enable/disable the parallel port.
■ Enable/disable the flash media reader.
■ Enable/disable the USB port.
Disabling the USB port also disables MultiBay
Ä
devices and ExpressCard devices on the advanced
port replicator.
■ Enable/disable the 1394 port.
■ Enable/disable the ExpressCard slot.
■ Enable/disable the Smart Card slot.
■ Enable/disable the eSATA port
AMT Options
■ Enable/disable Firmware Verbosity.
■ Enable/disable AMT Setup Prompt (Ctrl-P).
■ Enable/disable USB Key Provisioning Support.
■ Enable/disable Unconfigure AMT on next boot.
■ Select Terminal Emulation Mode.
❐ ANSI
❐ VT100
■ Enable/disable Firmware Progress Event Support.
■ Enable/disable Initiate Intel CIRA.
Set Security Level
Change, view, or hide security levels for all BIOS menu items.
Restore the default security settings.
Restore Security Defaults
Maintenance and Service Guide
5–19
6
Specifications
Computer specifications
Metric
U.S.
Dimensions
Depth
23.62 cm
9.30 in
Width
33.56 cm
13.21 in
Height (front to back)
Weight
3.13 to 3.49 cm
1.23 to 1.37 in
With 14-in SVA display assembly, UMA graphics, 4-cell
battery,1 512 MB SODIMM, WLAN card and antennas,
WWAN minicard connector, SIM connector, and WWAN
antennas, universal wideband antenna, no optical disk
drive, no Bluetooth module
2.12 kg
4.68 lb
Input power
Operating voltage
19.5 V dc 5% @ 3.33 A - 65 W
19.5 V dc 5% @ 4.62 A - 90 W
Operating current (max load)
Temperature
3.33 A or 4.62 A
Operating (not writing to optical disc)
Operating (writing to optical disc)
Nonoperating
0°C to 35°C
5°C to 35°C
-20°C to 60°C
32°F to 95°F
41°F to 95°F
-4°F to 140°F
Relative humidity
Operating
10% to 90%
5% to 95%
Nonoperating
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-15 m to 12,192 m
-50 ft to 10,000 ft
-50 ft to 40,000 ft
Nonoperating
Shock
Operating
125 g, 2 ms, half-sine
200 g, 2 ms, half-sine
Nonoperating
Random vibration
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
Nonoperating
Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
✎
Maintenance and Service Guide
6–1
Specifications
14.0-in SVA eDP display specifications
Metric
U.S.
Dimensions
Height
17.74 cm
6.9 in
Width
31.30 cm
12.3 in
14.0 in
Diagonal
35.56 cm
Number of colors
Contrast ratio
Brightness
Aspect ratio
Pixel resolution
Pitch
Up to 16.8 million
250:1 (typical)
200 nits (typical)
16:9
0.279 × 0.279 mm
Format
1366 × 768 - HD
1600 × 900 - HD+
Configuration
RGB vertical stripe
LED
Backlight
Character display
Total power consumption
Viewing angle
80 × 25
4.0 W
40° horizontal, +120°/-40° vertical (typical)
6–2
Maintenance and Service Guide
Specifications
Hard drive specifications
500-GB*
320-GB*
250-GB*
Dimensions
Height
9.5 mm (0.37 in)
70 mm (2.76 in)
101 g (3.56 oz)
SATA
9.5 mm (0.37 in)
70 mm (2.76 in)
101 g (3.56 oz)
SATA
9.5 mm (0.37 in)
70 mm (2.76 in)
101 g (3.56 oz)
SATA
Width
Weight
Interface type
Transfer rate
100 MB/sec
ATA security
100 MB/sec
ATA security
100 MB/sec
ATA security
Security
Seek times (typical read, including setting)
Single track
1.5 ms
1.5 ms
2.0 ms
Average
12.0 ms
12.0 ms
12.0 ms
Maximum
22.0 ms
22.0 ms
22.0 ms
Logical blocks
Disc rotational speed
Operating temperature
976,785,075
7200 rpm
625,142,448
7200 rpm
488,397,168
7200 rpm
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
Certain restrictions and exclusions apply. Contact technical support for details.
✎
Maintenance and Service Guide
6–3
Specifications
Solid state drive specifications
256-GB*
160-GB*
Dimensions
Height
9.5 mm (0.37-in)
100 mm (3.94-in)
70 mm (2.76)
80 g (2.82 oz)
SATA
7.0 mm (0.28-in)
100 mm (3.94-in)
70 mm (2.76)
76 g (2.68 oz)
SATA
Length
Width
Weight
Interface type
Read/Write bandwidth
Sequential read
Sequential write
Security
220 MB/sec
200 MB/sec
ATA security
500,118,192
250 MB/sec
70 MB/sec
ATA security
312,581,80
User Addressable Sectors
Operating temperature
0°C to 70°C (32°F to 158°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
Certain restrictions and exclusions apply. Contact technical support for details.
✎
6–4
Maintenance and Service Guide
Specifications
Blu-ray R/RE DVD±RW SuperMulti Drive specifications
Applicable disc
Read
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA,
mixed-mode CD, CD-I, CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-Extra, Portfolio, CD-R, CD-RW),
CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18),
DVD-R, DVD-RW, DVD+R, DVD+RW. DVD-RAM, BD-ROM,
BD-R, BD-RE
Write
CD-R, CD-RW, DVD+R, DVD+R(9), DVD+RW, DVD-R,
DVD-R(9), DVD-RW, DVD-RAM, BD-R, BD-RE
Random Access time
BD
< 230 ms
< 180 ms
< 180 ms
DVD
CD
Max media capacity
Read
50 GB
50 GB
2 MB
Write
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD-ROM
2X BD-ROM
24X CD-R
3600 KB/sec
10,800 KB/sec
9000 KB/sec
3600 KB/sec
2400 KB/sec
10800 KB/sec
8100 KB/sec
10800 KB/sec
8100 KB/sec
5400 KB/sec
5400 KB/sec
6750 KB/sec
9000 KB/sec
9000 KB/sec
9 MB/sec
16X CD-RW
8X DVD+R
6X DVD+RW
8X DVD-R
6X DVD-RW
4X DVD+R Dual Layer
4X DVD-R Dual Layer
5X DVD-RAM
2X BD-R
2X BD-RE
2X BD-RAM
Maintenance and Service Guide
6–5
Specifications
Blu-ray ROM with LightScribe DVD±RW SuperMulti DL Drive specifications
Applicable disc
Read
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA,
Mixed-Mode CD, CD-I, CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R,
CD-RW), CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW. DVD-RAM,
BD-ROM, BD-R, BD-RE
Write
CD-R, CD-RW, DVD+R, DVD+R(9), DVD+RW, DVD-R, DVD-R(9),
DVD-RW, DVD-RAM, LightScribe
Random Access time
BD
< 230 ms
< 190 ms
< 190 ms
DVD
CD
Max media capacity
Read
50 GB
8.5 GB
4.5 MB
Write
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD-ROM
4X BD-ROM
16X CD-R
3600 KB/s
10,800 KB/s
18000 KB/s
1200 KB/s
1500 KB/s
10800 KB/s
10800 KB/s
10800 KB/s
8100 KB/s
5400 KB/s
5400 KB/s
6750 KB/s
10X CD-RW
8X DVD+R
8X DVD+RW
8X DVD-R
6X DVD-RW
4X DVD+R Dual Layer
4X DVD-R Dual Layer
5X DVD-RAM
6–6
Maintenance and Service Guide
Specifications
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
Applicable disc
Read
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA,
Mixed-Mode CD, CD-I, CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R,
CD-RW), CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW. DVD-RAM
Write
CD-R, CD-RW, DVD+R, DVD+RW, DVD-R, DVD-RW, DVD-RAM,
LightScribe
Random Access time
CD
< 150 ms
< 160 ms
DVD
Max media capacity
Read
8.5 GB
8.5 GB
2.5 MB
Write
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD-ROM
24X CD-R
3600 KB/s
10,800 KB/s
3600 KB/s
2400 KB/s
10,800 KB/s
10800 KB/s
10,800 KB/s
8100 KB/s
5400 KB/s
5400 KB/s
6750 KB/s
16X CD-RW
8X DVD+R
8X DVD+RW
8X DVD-R
6X DVD-RW
4X DVD+R Dual Layer
4X DVD-R Dual Layer
5X DVD-RAM
Maintenance and Service Guide
6–7
Specifications
DVD-ROM Drive specifications
Applicable disc
Read:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA,
Mixed-Mode CD, CD-I, CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R,
CD-RW), CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM
Random Access time
CD
< 140 ms
< 160 ms
DVD
Max media capacity
Read
8.5 GB
2 MB
Cache buffer
Data transfer rate
24X CD-ROM
8X DVD
3,600 KB/sec
10,800 KB/sec
6–8
Maintenance and Service Guide
Specifications
System resource specifications
You can use Device Manager to get a graphical view of the system resources that control how the devices work on
the computer. System resources you can access from Device Manager are direct memory access (DMA) channels,
input/output (I/O) ports, interrupt request (IRQ) lines, and memory addresses.
If two devices require the same resource and create a device conflict, you can manually change the resource
settings in Device Manager to be sure each setting is unique.
CAUTION: Improperly changing resource settings can disable your hardware and cause your computer to malfunction or
become inoperable. Only users who have expert knowledge of computer hardware and hardware configurations should change
resource settings.
Ä
To view resource settings in Windows 7 and Windows Vista:
1. Select Start > Computer.
2. Click System properties near the top of the Computer folder.
3. On the left, click Device Manager.
4. On the View menu, click one of the following:
❏ Resources by type
❏ Resources by connection
To view resource settings in Windows XP:
1. Select Start > My Computer, or double-click My Computer on the desktop.
2. Under System Tasks, click View system information.
3. In the System Properties window, select the Hardware tab.
4. Click Device Manager.
5. On the View menu, click one of the following:
❏ Resources by type
❏ Resources by connection
Maintenance and Service Guide
6–9
7
Backup and recovery
Backup and recovery in Windows 7
Overview
To protect your information, use Windows® Backup and Restore to back up individual files and folders, back up
your entire hard drive (select models only), create system repair discs (select models only), or create system restore
points. In case of system failure, you can use the backup files to restore the contents of your computer.
Windows Backup and Restore provides the following options:
■
■
■
■
■
■
■
■
Creating a system repair disc (select models only)
Backing up individual files and folders
Creating a system image (select models only)
Scheduling automatic backups (select models only)
Creating system restore points
Recovering individual files
Restoring the computer to a previous state
Recovering information using recovery tools
For detailed instructions, perform a search for these topics in Help and Support.
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create system repair discs
(select models only) and your initial backup immediately after software setup. As you add new software and data
files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The
system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in
case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings
if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
■
■
■
Store personal files in the Documents library, and back it up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1. Display the screen you want to save.
Maintenance and Service Guide
7–1
Backup and recovery
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4. Save the document.
■
■
When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW,
DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD RW. The discs you use will depend on the type of
optical drive installed in your computer.
DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for backup
reduces the number of recovery discs required.
✎
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore Center, follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
✎
The backup process may take over an hour, depending on file size and the speed of the computer.
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or
create a system repair disc (select models only).
Windows® includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities,
✎
or changing Windows settings. Refer to Help and Support for more information.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows
from starting correctly.
■
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The image
includes the Windows operating system and software programs installed at the factory.
If you are unable to boot (start up) your computer and you cannot use the system repair discs you previously
created (select models only), you must purchase a Windows 7 operating system DVD to reboot the computer and
repair the operating system. For additional information, refer to the “Using a Windows 7 operating system DVD
(purchased separately)” section in this guide.
✎
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to recover your entire computer (select models only) or your files.
7–2
Maintenance and Service Guide
Backup and recovery
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
To recover your information using Startup Repair, follow these steps:
CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive. All files you have created
and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process
restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
Ä
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition and the HP Recovery partition.
To check for the Windows partition, select Start > Computer.
To check for the HP Recovery partition, click Start, right-click Computer, click Manage, and then click Disk
Management.
If the Windows partition or the HP Recovery partition is not listed, you must recover your operating
system and programs using the Windows 7 operating system DVD and the Driver Recovery disc (both
✎
purchased separately). For additional information, refer to the “Using a Windows 7 operating system
DVD (purchased separately)” section in this guide.
3. If the Windows partition and the HP Recovery partition are listed, restart the computer, and then press f8
before the Windows operating system loads.
4. Select Startup Repair.
5. Follow the on-screen instructions.
For additional information on recovering information using the Windows tools, perform a search for these topics
in Help and Support.
✎
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any
Ä
software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP
programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. Personal files
must be restored from a backup.
To recover the original hard drive image using f11, follow these steps:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition: click Start, right-click Computer, click
Manage, and then click Disk Management.
If the HP Recovery partition is not listed, you must recover your operating system and programs using the
Windows 7 operating system DVD and the Driver Recovery disc (both purchased separately). For additional
information, refer to the “Using a Windows 7 operating system DVD (purchased separately)” section in this
guide.
✎
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key
for Startup Menu” message is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Maintenance and Service Guide
7–3
Backup and recovery
Using a Windows 7 operating system DVD (purchased separately)
If you are unable to boot (start up) your computer and you cannot use the system repair discs you previously
created (select models only), you must purchase a Windows 7 operating system DVD to reboot the computer and
repair the operating system. Be sure that your most recent backup (stored on discs or on an external drive) is easily
accessible. To order a Windows 7 operating system DVD, go to http://www.hp.com/support, select your country or
region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact
information, refer to the Worldwide Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats the hard drive. All
Ä
files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the
recovery process helps you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows 7 operating system DVD, follow these steps:
This process takes several minutes.
✎
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the
Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
7–4
Maintenance and Service Guide
Backup and recovery
Backup and recovery in Windows Vista
Overview
To protect your information, use the Backup and Restore Center to back up individual files and folders, back up
your entire hard drive (select models only), or create system restore points. In case of system failure, you can use
the backup files to restore the contents of your computer.
The Backup and Restore Center provides the following options:
■
■
■
■
■
■
■
Backing up individual files and folders
Backing up the entire hard drive (select models only)
Scheduling automatic backups (select models only)
Creating system restore points
Recovering individual files
Restoring the computer to a previous state
Recovering information using recovery tools
For detailed instructions, perform a search for these topics in Help and Support.
✎
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup. You can back up your information to an optional
external hard drive, a network drive, or discs.
Note the following when backing up:
■
■
■
Store personal files in the Documents folder, and back it up regularly.
Back up templates that are stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1. Display the screen you want to save.
2. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4. Save the document.
Maintenance and Service Guide
7–5
Backup and recovery
■
When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW,
DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD RW. The discs you use will depend on the type of
optical drive installed in your computer.
DVDs and DVDs with double-layer (DL) support store more information than CDs, so using them for
backup reduces the number of recovery discs required.
✎
■
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore Center, follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
✎
✎
The backup process may take over an hour, depending on file size and the speed of the computer.
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools: You can use the Backup and Restore Center to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows
from starting correctly.
■
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The image
includes the Windows operating system and software programs installed at the factory.
the computer and repair the operating system. For additional information, refer to the “Using a Windows Vista
operating system DVD (purchased separately)” section in this chapter.
✎
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1. Select Start > All Programs > Maintenance > Backup and Restore Center.
2. Follow the on-screen instructions to recover your entire computer (select models only) or your files.
Windows includes the User Account Control feature to improve the security of your computer. You may be
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. Refer to Help and Support for more information.
✎
7–6
Maintenance and Service Guide
Backup and recovery
To recover your information using Startup Repair, follow these steps:
CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive. All files you have created
and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process
restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery.
Ä
1. If possible, back up all personal files.
2. If possible, check for the presence of the Windows partition and the HP Recovery partition. To find the
partitions, select Start > Computer.
If the Windows partition and the HP Recovery partition have been deleted, you must recover your operating
system and programs using the Windows Vista operating system DVD and the Driver Recovery software (both
✎
purchased separately). For additional information, refer to the “Using a Windows Vista operating system
DVD (purchased separately)” section in this chapter.
3. Restart the computer, and then press f8 before the Windows operating system loads.
4. Select Repair your computer.
5. Follow the on-screen instructions.
For additional information on recovering information using the Windows tools, perform a search for these topics
in Help and Support.
✎
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any
Ä
software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP
programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. Personal files
must be restored from a backup.
If your computer includes a solid-state drive (SSD), you may not have a recovery partition. Recovery discs have
been included for computers that do not have a partition. Use these discs to recover your operating system and
software. To check for the presence of a recovery partition, select Start > Computer. If the partition is present,
an HP Recovery drive is listed in the Hard Disk Drives section of the window.
✎
To recover the original hard drive image using f11, follow these steps:
1. If possible, back up all personal files.
2. If possible, check for the presence of the HP Recovery partition. To find the partition, select
Start > Computer.
If the HP Recovery partition has been deleted, you must recover your operating system and programs using the
Windows Vista operating system DVD and the Driver Recovery software (both purchased separately). For
✎
additional information, refer to the “Using a Windows Vista operating system DVD (purchased
separately)” section in this chapter.
3. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message
is displayed at the bottom of the screen.
4. Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5. Follow the on-screen instructions.
Maintenance and Service Guide
7–7
Backup and recovery
Using a Windows Vista operating system DVD (purchased separately)
If you are unable to startup your computer, you must purchase a Windows Vista operating system DVD to restart
the computer and repair the operating system. Be sure that your most recent backup (stored on discs or on an
external drive) is easily accessible. To order a Windows Vista operating system DVD, go to
http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the
DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet
included with the computer.
CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive.
Ä
All files you have created and any software installed on the computer are permanently removed. When reformatting is complete,
the recovery process helps you restore the operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
This process takes several minutes.
✎
1. If possible, back up all personal files.
2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before
the Windows operating system loads.
3. When prompted, press any keyboard key.
4. Follow the on-screen instructions.
5. Click Next.
6. Select Repair your computer.
7. Follow the on-screen instructions.
7–8
Maintenance and Service Guide
Backup and recovery
Backup and recovery in Windows XP
Overview
To protect your information, use the Windows Backup utility (select models only) to back up files and folders or
create recovery points. In case of system failure, you can use the backup files to restore your computer.
Windows provides the following options:
■
■
■
■
■
Backing up individual files and folders
Backing up all files and folders
Scheduling automatic backups
Creating recovery points
Recovering information
For detailed instructions, perform a search for these topics in Help and Support.
✎
✎
In case of system instability, HP recommends that you print the recovery procedures and save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your initial backup
immediately after software setup. As you add new software and data files, you should continue to back up your
system on a regular basis to maintain a reasonably current backup. You can back up individual files or folders to an
optional external hard drive or to a network drive.
Note the following when backing up:
■
■
■
Store personal files in the My Documents folder, and back it up periodically.
Back up templates stored in their associated programs.
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a. Display the screen you want to save.
b. Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c. Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
d. Save the document.
To create a backup using the Windows Backup utility (select models only), follow these steps:
Be sure that the computer is connected to AC power before you start the backup process.
✎
✎
The backup process may take over an hour, depending on file size and the speed of the computer.
1. Select Start > All Programs > Accessories > System Tools > Backup.
Maintenance and Service Guide
7–9
Backup and recovery
2. Follow the on-screen instructions.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
■
Windows recovery tools (select models only): You can use the Windows Backup utility to recover information
you have previously backed up.
■
Operating System and Driver Recovery discs (included with your computer): You can use the discs to recover
your operating system and programs installed at the factory.
Recovering your information
To recover information you previously backed up, follow these steps:
1. If possible, back up all personal files.
2. Select Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard opens.
3. Select Restore files and settings, and then select Next.
4. Follow the on-screen instructions.
For additional information on initiating a recovery in Windows, perform a search for this topic in
Help and Support.
✎
Recovering the operating system and programs
CAUTION: The recovery process reformats and completely erases the hard drive. All files you have created and any software
Ä
installed on the computer are permanently removed. The recovery process reinstalls the original operating system as well as
software and drivers. Software, drivers, and updates not installed by HP must be manually reinstalled. Personal files must be
restored from a backup.
To recover your operating system and programs, follow these steps:
1. If possible, back up all personal files.
2. Insert the Operating System disc into the optical drive.
3. Shut down the computer.
4. Turn on the computer.
5. Follow the on-screen instructions to install the operating system.
6. After the operating system is installed, remove the Operating System disc and insert the Driver
Recovery disc.
7. Follow the on-screen instructions to install the drivers and programs.
7–10
Maintenance and Service Guide
Connector pin assignments
1394a
Pin
1
Signal
Send data, twisted pair B-
Send, twisted pair B+
Receive data, twisted pair A-
Receive, twisted pair A+
2
3
4
External monitor
Pin
1
Signal
Red analog
Green analog
Blue analog
Not connected
Ground
2
3
4
5
6
Ground analog
Ground analog
Ground analog
+5 VDC
7
8
9
10
11
12
13
14
15
Ground
Monitor detect
DDC 2B data
Horizontal sync
Vertical sync
DDC 2B clock
8–2
Maintenance and Service Guide
Connector pin assignments
DisplayPort
This is the pinout for the source-side connector; the sink-side connector pinout has lanes 0-3 reversed in order,
that is, lane 3 will be on pin 1 and 3 while lane 0 will be on pin 10 and 12.
✎
Pin
1
Signal
Lane 0 -
2
Ground
3
Lane 0 +
4
Lane 1 +
5
Ground
6
Lane 1 -
7
Lane 2 +
8
Ground
9
Lane 2 -
10
11
12
13
14
15
16
17
18
19
20
Lane 3 +
Ground
Lane 3 -
CONFIG1 connected to ground*
CONFIG2 connected to ground*
Auxiliary Channel +
Ground
Auxiliary channel -
Hot plug detect
Return for power
Power
*Pins 13 and 14 may either be directly connected to ground or connected to ground through a pulldown device.
Maintenance and Service Guide
8–3
9
Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC,
or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or region
where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region where
the computer is used.
Requirements for all countries and regions
The following requirements are applicable to all countries and regions:
■
■
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the
country or region where the power cord set will be used.
■
■
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or
250 V AC, as required by the power system of each country or region.
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector for mating with the appliance inlet on the back of the computer.
Maintenance and Service Guide
9–1
Power cord set requirements
Requirements for specific countries and regions
Country/region
Australia
Accredited agency
EANSW
OVE
Applicable note number
1
1
1
2
1
1
1
1
1
3
1
1
5
4
1
1
4
1
2
Austria
Belgium
CEBC
CSA
Canada
Denmark
DEMKO
FIMKO
UTE
Finland
France
Germany
VDE
Italy
IMQ
Japan
METI
The Netherlands
Norway
KEMA
NEMKO
CCC
The People's Republic of China
South Korea
Sweden
EK
SEMKO
SEV
Switzerland
Taiwan
BSMI
The United Kingdom
The United States
BSI
UL
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
9–2
Maintenance and Service Guide
10
Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste.
Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING: The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid
Å
Ä
damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this chapter can result in damage to display components. The only components intended for
recycling purposes are the liquid crystal display (LCD) panel and the backlight. When you remove these components, handle
them carefully.
Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might
require special handling at end-of-life. Disposal of mercury may be regulated because of environmental
considerations. For disposal or recycling information, contact your local authorities, or see the Electronic
✎
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2.
The procedures provided in this chapter are general disassembly instructions. Specific details, such as screw
sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
✎
Maintenance and Service Guide
10–1
Recycling
Perform the following steps to disassemble the display assembly:
1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel
until the bezel disengages from the display assembly.
3. Remove the display bezel 3.
10–2
Maintenance and Service Guide
Recycling
4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
5. Remove all screws 1 that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly 2 from the display enclosure.
7. Turn the display panel assembly upside down.
8. Remove all screws that secure the display panel frame to the display panel.
Maintenance and Service Guide
10–3
Recycling
9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame.
10. Remove the display panel frame 2 from the display panel.
11. Remove the screws 1 that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover 2 and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
15. Remove the backlight cables 1 from the clip 2 in the display panel.
10–4
Maintenance and Service Guide
Recycling
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING: The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging
this component and causing exposure to the mercury.
Å
18. Remove the backlight from the backlight frame.
Maintenance and Service Guide
10–5
Recycling
19. Disconnect the display cable 1 from the LCD panel.
20. Remove the screws 2 that secure the LCD panel to the display rear panel.
21. Release the LCD panel 3 from the display rear panel.
22. Release the tape 4 that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
10–6
Maintenance and Service Guide
Index
1394a port
location 2–12
pin assignments 8–2
removal 4–46
Bluetooth module cable
illustrated 3–10
A
removal 4–48
AC adapter, spare part number 3–13
accessory battery connector 2–13
ambient light sensor/connector board
illustrated 3–8
spare part number 3–4
Bluetooth module compartment cover
illustrated 3–11
removal 4–47
antenna
spare part number 3–4
Blu-ray R/RE DVD RW SuperMulti Drive
precautions 4–2
location 2–3
removal 4–34
removal 4–20
specifications 6–5
spare part number 4–27
WLAN product description 1–3
WWAN product description 1–3
audio, product description 1–4
Audio/ExpressCard board
removal 4–44
audio-in jack
location 2–12
pin assignments 8–1
audio-out jack
Blu-ray ROM with LightScribe DVD RW SuperMulti
DL Drive
precautions 4–2
removal 4–20
specifications 6–6
bottom components 2–13
business card holder 2–13
buttons
location 2–12
pin assignments 8–1
Caps lock 2–5
display release 2–10
Num lock 2–5
pointing stick 2–7
power 2–4
B
base enclosure, spare part number 3–5
battery
bay 2–13
QuickLook 2–4
QuickWeb 2–4
release latch 2–13
removal 4–7
volume down 2–5
bays
volume mute 2–5
volume up 2–5
battery 2–13
wireless 2–4
hard drive 2–13
C
Bluetooth module
compartment 2–10
cable kit
contents 3–10
spare part number 3–4
cables, service considerations 4–1
Maintenance and Service Guide
Index–1
Index
Caps lock
button 2–5
illustrated 3–9
display bezel
light 2–9
compartments
illustrated 3–8
memory module 2–13
wireless modules 2–13
components
removal 4–31
display cable
bottom 2–13
illustrated 3–8
buttons 2–4
removal 4–34
fingerprint reader 2–4
front 2–10
display components
keys 2–6
recycling 10–1
left-side 2–12
lights 2–8
display hinge covers
removal 4–33
pointing device 2–7
rear 2–11
display hinges
right-side 2–12
illustrated 3–8
switches 2–4
removal 4–32
computer feet
display inverter, removal 10–3
display panel
illustrated 3–8
removal 4–32
display release button 2–10
display switch, location 2–2
DisplayPort
locations 4–6
spare part number 4–6
Computer Setup
computer, specifications 6–1
connectors
location 2–11
1394a 2–12
accessory battery 2–13
audio in 2–12
pin assignments 8–3
docking connector 2–13
DriveLock
audio out 2–12
DisplayPort 2–11
docking 2–13
eSATA 2–12
monitor 2–11
power 2–11
RJ-11 (modem) 2–12
RJ-45 (network) 2–12
service considerations 4–1
USB 2–12
DVD RW and CD-RW SuperMulti Double-Layer
Combo Drive with LightScribe
precautions 4–2
removal 4–20
specifications 6–7
DVD-ROM Drive
D
precautions 4–2
removal 4–20
specifications 6–8
digital card 1–4
diskette drive, product description 1–3
display
E
electrostatic discharge 4–2
equipment guidelines 4–4
eSATA/USB
removal 4–27
specifications 6–2
connector 2–12
display back cover
pin assignments 8–6
Index–2
Maintenance and Service Guide
Index
Ethernet, product description 1–3
expansion memory compartment cover, illustrated 3–11
expansion memory module 4–16
removal 4–16
I
internal display switch 2–4
J
jacks
spare part number 3–6
audio out 2–12
audio-in 2–12
audio-out 2–12
headphone 2–12
microphone 2–12
modem 2–12
network 2–12
RJ-11 (modem) 2–12
RJ-45 (network) 2–12
ExpressCard slot 2–12
ExpressCard slot bezel, illustrated 3–11
external monitor port
location 2–11
pin assignments 8–2
F
fan
removal 4–35
feet
K
key components 2–6
keyboard
locations 4–6
spare part number 4–6
Fingerprint reader 2–5
front components 2–10
function keys 2–6
product description 1–4
removal 4–22
keyboard light button, location 2–2
keyboard light, location 2–2
keys
G
esc 2–6
fn 2–6
function 2–6
graphics subsystem, product description 1–1
grounding equipment and methods 4–2
H
numeric keypad 2–6
Windows applications 2–6
Windows logo 2–6
hard drive
illustrated 3–12
precautions 4–2
product description 1–2
removal 4–9
L
left-side components 2–12
light components 2–8
lights
specifications 6–3
upgrade bay 3–6
Caps lock 2–9
Num lock 2–9
QuickLook 2–8
QuickWeb 2–8
TouchPad 2–8
hard drive bay 2–13
hard drive bay cover
illustrated 3–11
removal 4–9
spare part number 3–4
hard drive bracket, removal 4–10
headphone jack, location 2–12
heat sink
removal 4–35
hinge covers
volume down 2–9
volume mute 2–9
volume up 2–9
removal 4–33
M
hinges
mass storage devices
illustrated 3–12
spare part number 3–6
removal 4–32
Maintenance and Service Guide
Index–3
Index
memory module
pin assignments
product description 1–2
removal 4–16
audio-in 8–1
audio-out 8–1
spare part number 4–16
memory module compartment 2–13
memory module compartment cover
removal 4–16
spare part number 3–4
microphone
headphone 8–1
microphone 8–1
modem 8–4
monitor port 8–2
network 8–4
RJ-11 (modem) 8–4
RJ-45 (network) 8–4
Universal Serial Bus (USB) port 8–4
plastic parts 4–1
plastics kit
locations 2–2
product description 1–3
removal 4–34
microphone jack
content 3–11
location 2–12
contents 3–11
pin assignments 8–1
model name 4–5
spare part number 3–4
pointing device
model number 3–1
modem jack, location 2–12
modem module
product description 1–3
removal 4–49
modem module cable
illustrated 3–10
components 2–7
illustrated 2–7
product description 1–4
pointing stick 2–7
pointing stick button 2–7
ports
1394a 2–12
removal 4–52
spare part number 3–4
monitor port
DisplayPort 2–11
external monitor 2–11
USB 2–12
location 2–11
power
pin assignments 8–2
button 2–4
light 2–8
power button board
removal 4–26
power connector 2–11
power cord
N
network jack
location 2–12
pin assignments 8–4
Num lock
button 2–5
requirements 9–1
spare part number 3–13
power light, front 2–10
power requirements, product description 1–4
primary memory module
removal 4–18
light 2–9
numeric keypad keys 2–6
O
optical drive
illustrated 3–12
precautions 4–2
product description 1–2
removal 4–20
spare part number 3–5
processor
removal 4–40
product description
audio 1–3
optical drive bracket, removal 4–21
optical drive kit 3–6
diskette drive 1–3
display panel 1–1
docking 1–4
P
packing guidelines 4–3
Index–4
Maintenance and Service Guide
Index
external media card 1–4
hard drives 1–2
spare part number 3–13
screw location
keyboard 1–4
Phillips
memory 1–2
microphone 1–3
modem 1–3
operating system 1–5
optical drives 1–2
pointing devices 1–4
ports 1–4
M2.0 × 2.0 broadhead 4–23
M2.0 × 3.0 4–26
M2.0 × 4.0 broadhead 4–44
M2.0 × 5.0 captive 4–16
M2.5 × 10.0 4–20
power requirements 1–4
processor 1–1
security 1–5
M2.5 × 5.0 4–32
M3.0 × 3.0 4–10
serviceability 1–7
upgrade hard drive bay 1–3
webcam 1–3
Torx
SD Card Reader 2–10
wireless 1–3
security cable slot 2–11
Q
QuickLook
button 2–4
light 2–8
QuickWeb
button 2–4
light 2–8
R
rear components 2–11
recovery, system 7–1
recycling
battery 10–1
display components 10–1
removal/replacement
preliminaries 4–1
procedures 4–5
security, product description 1–5
serial number 3–1
right-side components 2–12
RJ-11 (modem) jack
location 2–12
pin assignments 8–4
RJ-45 (network) jack
location 2–12
service considerations 4–1
service tag
location 4–5
part number 4–5
serial number 4–5
pin assignments 8–4
RTC battery
serviceability, product description 1–7
SIM slot 2–13
removal 4–39
SIM, removal 4–8
smartcard reader 2–12
solid state drive
illustrated 3–12
spare part number 3–6
specifications 6–4
S
screw kit
contents 3–13
Maintenance and Service Guide
Index–5
Index
spare part numbers, sequential listing 3–14
speakers 2–10
removal 4–45
specifications
volume down light 2–9
volume mute button 2–5
volume mute light 2–9
volume up button 2–5
volume up light 2–9
Blu-ray ROM with LightScribe DVD RW
SuperMulti DL Drive 6–6
computer 6–1
W
warranty period 4–5
webcam light, location 2–2
webcam module
display 6–2
removal 4–34
DVD RW and CD-RW SuperMulti Double-Layer
Combo Drive with LightScribe 6–7
DVD-ROM Drive 6–8
spare part number 4–34
webcam, location 2–2
Windows applications key 2–6
Windows logo key 2–6
wireless
hard drive 6–3
IRQ, DMA, I/O, and memory addresses 6–9
solid state drive 6–4
antenna
location 2–3
removal 4–34
system resources 6–9
switch cover
removal 4–22
switch, internal display 2–4
system board
spare part number 3–9
button 2–4
module compartment 2–13
module compartment cover
illustrated 3–11
removal 4–50
system recovery 7–1
spare part number 3–4
WLAN module
T
tag, service 4–5
illustrated 3–6
thermal heatshield, spare part number 3–13
thermal material 3–5
tools required 4–1
top cover
removal 4–11
WLAN module compartment cover
removal 4–14
removal 4–42
TouchPad 2–7
spare part number 3–4
workstation guidelines 4–4
WWAN module
button 2–5
removal 4–14
light 2–8
WWAN module compartment cover
removal 4–14
TouchPad buttons 2–7
TouchPad scroll zone 2–7
spare part number 3–4
U
Universal Serial Bus (USB) port
location 2–12
pin assignments 8–5
upgrade bay, hard drive option 3–6
upgrade drive bay 2–12
V
volume down button 2–5
Index–6
Maintenance and Service Guide
|
Toshiba Rav Sm562ct E User Manual
Toshiba E Studio 55 User Manual
Toshiba B 852 User Manual
Stinger Sr80 User Manual
Philips 873e14 User Manual
MAKITA G7300R User Manual
Lexmark 138 User Manual
LENOVO Z70 80 02 User Manual
GARLAND TECHNOLOGY PACKETMAX AA100G64AC 02 User Manual
BLACK DECKER RO410 User Manual