HP 9200c Digital Sender
Support Guide
HP 9200C Digital Sender
Support Guide
Copyright and License
Trademark Credits
© 2004 Copyright Hewlett-Packard
Development Company, LP
Microsoft® and Windows® are U.S.
registered trademarks of Microsoft
Corporation.
Reproduction, adaptation, or translation
without prior written permission is
prohibited, except as allowed under the
copyright laws.
Adobe® and Acrobat® are trademarks of
Adobe Systems Incorporated.
The information contained in this document
is subject to change without notice.
The only warranties for HP products and
services are set forth in the express
warranty statements accompanying such
products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable
for technical or editorial errors or omissions
contained herein.
Part number Q5916-90930
Edition 1, 11/2004
Table of contents
Parts of the digital sender ...................................................................................................4
General tab .........................................................................................................................9
Authentication tab .............................................................................................................1 4
Fax tab .............................................................................................................................1. 6
Log tab .............................................................................................................................3. 5
Uninstalling the software .........................................................................................................35
The embedded Web server ..............................................................................................37
Configure Device menu ....................................................................................................41
ENWW
Table of contents
iii
To restrict software access ...............................................................................................55
Downloading the new firmware from the HP Web site .....................................................60
Upgrading the HP Jetdirect Inside firmware .....................................................................62
Cleaning the digital sender ...............................................................................................63
Replacing the mylar sheet ................................................................................................66
Sources for information about problems .................................................................................71
Digital-sender event log messages .........................................................................................89
Windows event log error messages ........................................................................................91
Troubleshooting SMTP and LDAP servers .............................................................................93
Finding an SMTP server address .....................................................................................95
Verifying an SMTP address ..............................................................................................95
Digital Sender specifications .................................................................................................101
iv
ENWW
vi
ENWW
About the digital sender
1
The HP 9200C Digital Sender connects directly to your network and uses the included
HP Digital Sending Software (HP DSS) program to convert black-and-white and color
documents, drawings, and photographs into an electronic form and then distribute them
directly to several kinds of destinations.
●
●
●
●
E-mail—Scan a document and send it to one or more e-mail recipients in the form of
a .PDF, .JPEG, .TIFF, or .MTIFF file.
Secondary (secure) E-mail—Send a document by using a secure third-party e-mail
solution.
Fax—Scan a document and send it to a local area network (LAN) fax, Internet fax, or
Windows® 2000 fax destination. (The device does not have analog fax capability.)
Workflow—Scan a document and save it to a network folder or file transfer protocol
(FTP) site along with additional information about the document. A third-party software
program can then retrieve and decipher the information, and perform the appropriate
operation on the scanned image. A printer can also be set up as a workflow destination,
allowing scanned documents to be printed.
●
Network Folder—Scan a document and send it to a folder on the network.
The digital sender includes a flatbed scanner as well as an automatic document feeder
(ADF) that can accept up to 50 pages.
The digital sender supports network authentication, allowing you to require users to log in
before they can use the digital-sending options. It can also make use of Lightweight
Directory Access Protocol (LDAP) to find and use e-mail addresses on directory servers that
are located elsewhere on a network.
Installing the device is simply a matter of connecting it to your network, installing the HP
DSS program that comes with the device, and configuring the digital-sending features. The
digital sender operates as a standalone unit on the network and does not require network
privileges for administration.
ENWW
1
Features
The digital sender includes the following features:
●
Digital sending—Send scanned files to e-mail addresses, fax destinations, network
folders, and workflow folders. Digital-sending functions are carried out by the HP Digital
Sending Software (HP DSS), which is included with the device.
●
●
●
●
●
●
●
ADF—The legal-size ADF accepts up to 50 pages, and includes built-in duplexing for
scanning both sides of a double-sided document.
Interactive touchscreen control panel—Intuitive onscreen menus and wizards help
you to complete digital-sending tasks.
Flatbed scanner—The letter/A4-size scanner can scan in both black-and-white and
color, with the ability to scan up to 1 mm (0.04 inch) from the paper edge.
Memory—The device comes standard with 128 megabytes (MB) of random access
memory (RAM).
Hard disk—The device includes a 20-gigabyte (GB) internal hard drive for storing
documents and settings.
Connectivity—The device provides a 10/100Base-T port and an enhanced input/output
(EIO) expansion slot for connectivity.
HP Jetdirect Inside—An HP Jetdirect embedded print server is integrated into the
device for reliable network connectivity.
Specifications
The following are the digital sender specifications.
Paper handling
The HP 9200C Digital Sender supports the following standard paper sizes:
●
●
●
●
●
●
Letter: 215.9 x 279 mm (8.5 x 11 inches)
Executive: 190 x 254 mm (7.5 x 10 inches)
A4: 210 x 297 mm (8.3 x 11.7 inches)
A5: 148 x 210 mm (5.83 x 8.27 inches)
B5: 176 x 250 mm (6.9 x 9.8 inches)
Legal (from the ADF only): 215.9 x 355.6 mm (8.5 x 14 inches)
Paper weight: 60 to 120 g/m2 (16 to 32 lb)
Up to 50 sheets of paper can be stacked in the ADF, with a maximum height of 5 mm
(0.2 inch).
2
Chapter 1 About the digital sender
ENWW
Performance
The following sections give specific performance statistics for the digital sender.
ADF performance
The following table shows the page per minute (ppm) speed of the digital sender ADF.
Mode
Dots per inch (dpi)
Speed (ppm), A4
Speed (ppm),
Letter
Simplex Mono Mode
Simplex Mono Mode
Simplex Color Mode
Duplex Mono Mode
Duplex Mono Mode
Duplex Color Mode
600 x 600
600 x 300
600 x 300
600 x 600
600 x 300
600 x 300
29
46
29
18
24
18
30
47
30
18
24
18
Flatbed performance
The following table shows the seconds per scan cycle for scanning on the flatbed.
These performance numbers are for scanning only. They do not include the time that it takes
the digital sender to process and send the scanned file.
NOTE
Mode
dpi
Speed (seconds), A4
Speed (seconds), Letter
Black and White
Black and White
Color
600 x 600
600 x 300
600 x 600
4.1
3.1
5.9
3.9
3.0
5.6
Duty cycle
●
●
The maximum duty cycle is 60,000 total images scanned per month.
The average duty cycle is 3,600 total images scanned per month.
ENWW
Specifications
3
Parts of the digital sender
The following figures illustrate the digital sender parts.
1
2
3
4
5
Jam release button
Control panel
On/off switch
Output bin
ADF input bin
6
7
8
9
ADF cable
Control-panel cable
10/100Base-T network port
EIO port
10 Power connector
4
Chapter 1 About the digital sender
ENWW
11 Scanner lock
12 Serial number
The following figure shows the features of the digital sender control panel.
3
4
1
2
5
6
7
8
12
11
10
9
1
2
3
4
5
6
7
8
9
Touchscreen graphical display
Numeric keypad
RESET button
MENU button
SLEEP button and LED
STATUS button
STOP button
START button and LED
Attention LED
10 Data LED
11 Ready LED
12 Contrast control wheel
ENWW
Specifications
5
Environment and network
The following are environment and network considerations for the product.
Environmental ranges
Install the device in an area that is within the following temperature and humidity ranges.
The operating environment should be stable, with no abrupt changes in temperature or
humidity that might damage the device. If you move the device from a cold environment to a
warm one, wait about two hours before using it.
CAUTION
Temperature
Operating
Storage
0° to 40°C (32° to 104°F)
-40° to 60°C (-40° to 140°F)
Humidity
Operating
Storage
15 to 80% noncondensing (up to 40°C [104°F])
15 to 90% (up to 60°C [140°F])
Network components used for digital-sending
The following table describes the network components used for digital sending.
Component
Description
Network server running Windows® 2000
Professional, Server, or Advanced Server;
Windows XP Professional; or Windows Server
2003 Standard or Enterprise Server
The server contains the following components:
●
●
HP DSS
HP MFP DSS Configuration Utility—used to
configure and monitor digital-sending
features after the HP DSS program has
been installed
●
Windows 2000 Fax service—required only
when the Windows 2000 Fax service is the
method of fax transport
Network
Fast Ethernet 100Base-TX or Ethernet 10Base-T
6
Chapter 1 About the digital sender
ENWW
Component
Description
Digital senders or HP multi-function peripheral
(MFP) products
An HP DSS server can support up to 250 HP
9200C Digital Senders or MFP products on the
same network. Each device can be individually
configured to support any or all of the digital-
sending options.
NOTE
HP DSS does not support the HP 9100C or
8100C Digital Senders.
Web browser
Users can use a Web browser from any
computer on the network to configure and
monitor the digital sender by using HP Web
Jetadmin, or the digital sender's embedded Web
server.
SMTP gateway
LAN fax server
This gateway facilitates the e-mail and Internet
fax digital-sending options.
A LAN fax server is a network device that
centrally handles the sending and receiving of
large numbers of fax jobs. HP DSS can be used
to configure the digital sender to route outgoing
faxes to a LAN fax server.
LDAP server
An LDAP server is a directory server that
contains recipients' names and e-mail addresses
and supports Lightweight Directory Access
Protocol (LDAP). HP DSS uses the LDAP server
to obtain addresses for the digital-sender
address book.
FTP server
A file transfer protocol (FTP) server can be used
as a destination for documents scanned by the
digital sender.
Domain controller/Novell directory server
In order to support user authentication, the
digital sender must have access to a domain
controller or Novell directory server in order to
validate the user's login information.
Network printer
A network printer can be set up as a destination
for documents scanned by the digital sender.
Novell NetWare support
If Novell file servers are used on the network, HP DSS can write files into network folders
and support network fax folders that reside on Novell servers. The Novell client software
must be installed on the network and be configured correctly before Novell-specific attributes
can be configured in HP DSS.
ENWW
Environment and network
7
In order to support Novell NetWare authentication and Novell digital sending destinations,
HP DSS requires both of the following components:
●
Novell NetWare version 3.12, 3.2, 4.11, 4.2, 5, or 6 running on the Novell NetWare server
-AND-
●
Novell NetWare Client version 4.6 (or later) installed on the Windows computer that runs
HP DSS
Space requirements
The following figures illustrate the space requirements for the HP 9200C Digital Sender.
The digital sender requires 90 mm (3.5 inches) of free space behind the device in order to
fully open the top.
NOTE
8
Chapter 1 About the digital sender
ENWW
Configuring HP DSS
2
Without using the HP DSS service, the digital sender can only scan documents and send
them as attachments to e-mail. If you prefer, the digital sender can be used in this way,
without installing the HP DSS service. The e-mail settings can be configured by using the
control-panel menus. However, to enable all of the other digital-sending features, including
send-to-folder, send-to-fax, and send-to-workflow, the HP DSS service must be installed.
The digital-sending features must be configured within the HP DSS service before they can
be made available on the device. This section explains how to configure these digital-
sending features.
Using the Digital Sending Software
See the HP 9200C Digital Sender Getting Started Guide for instructions about unpacking the
NOTE
digital sender, installing the software, and setting up the initial configuration. The following
instructions cover the configuration options in more detail.
Use the HP MFP Digital Sending Software Configuration Utility to configure all of the digital-
sender features. Each feature that is enabled appears on the digital-sender control-panel
display as an option.
Use the following instructions to open the program.
1. On the server where HP DSS was installed, click Start, click Programs, click Hewlett-
Packard, click HP MFP Digital Sending Software, and then click Configuration Utility.
2. In the HP Digital Sending Software Configuration dialog box, select This computer
and click OK.
General tab
The General tab contains HP DSS license and administrator contact information.
When the HP Digital Sending Software is installed for the first time, the software is fully
functional in trial mode for a set period of time. The Licenses section of the General tab
displays a “Trial License” entry. The remaining trial period is displayed in this entry. When
the trial period expires, the software becomes inactive until a valid license is installed.
The digital sender comes with a one-seat license. Additional licenses can be purchased in 1,
5, 10, and 50 seat varieties. Each seat enables digital sending features on one digital sender
or MFP. You can install as many licenses as you like in order to accumulate seats, but 250 is
the maximum number of devices that can be supported by a server.
ENWW
Using the Digital Sending Software
9
Click the Add button to type in the license key code for the HP Digital Sending Software.
Fill in the administrator contact information in the Administrator Information section of this
tab. Select the Notify administrator of critical errors check box if you would like to be
notified by e-mail about errors that require administrative assistance.
Click the Help button to get more information about this tab.
NOTE
E-mail tab
The device can send SMTP e-mail messages to Internet addresses. It uses SMTP-MIME to
deliver these messages. It is highly recommended that the SMTP gateway be located on
your own local area network. However, you can also configure your product for e-mail
functionality even if your mail services are provided by an outside Internet service provider
(ISP) over a digital subscription line (DSL).
If your server supports it, ESMTP (Extended SMTP) can be used to send e-mail. This
capability is automatically detected and no specific configuration steps are necessary. The
e-mail service is also compatible with the DSN (Delivery Status Notification) standard.
The document that you scan at the device becomes an attachment to your e-mail message.
The portable document format (.PDF) file format is most often used for the attachments,
which gives recipients the ability to both view and print them. Users can obtain a free copy of
the Adobe® Acrobat® Reader for viewing .PDFs from the Adobe Systems Incorporated Web
Use the E-Mail tab of the configuration program to configure and organize the SMTP e-mail
servers that HP DSS uses to send e-mail messages.
10
Chapter 2 Configuring HP DSS
ENWW
To add SMTP servers
1. Click Find Servers to find all of the SMTP servers on the network.
2. A list of SMTP servers appears. Select one or more and click OK. The selected servers
are loaded into the SMTP Gateway Server list.
If the discovery process does not find any SMTP servers, use the Add button on the E-mail
tab to add the SMTP server manually by typing in the host name or IP address of the SMTP
server.
NOTE
ENWW
Using the Digital Sending Software
11
3. Select each server and click the Edit... button.
The Edit SMTP Gateway dialog box appears.
4. If you want to set a maximum file size for the specified SMTP gateway, select it in the
Maximum File Size drop-down list. If an e-mail attachment is larger than this file size,
the attachment will be divided into two or more smaller attachments.
5. Click Test to verify the presence of the SMTP gateway.
If the test fails, double-check the gateway address and then contact your network
administrator to see if the SMTP server is functioning.
NOTE
6. Click OK to save the SMTP settings.
12
Chapter 2 Configuring HP DSS
ENWW
7. Add more SMTP servers as needed, and use the Move arrow buttons to change the
priority order.
8. Click Apply to save the E-mail settings.
Click the Help button to get more information about this tab.
NOTE
Secondary E-mail tab
A number of third-party software vendors offer services for secure e-mail delivery. For
example, Omtool offers a secure email solution that encrypts email messages and requires
authentication for recipients before the email message can be delivered. These programs
help organizations comply with new laws being enacted such as the E-sign act and the
HIPAA requirements for electronic delivery of confidential documents. The Secondary E-mail
feature is designed to work with one of these third-party software programs for users that
require an extra measure of data security. It differs from the regular e-mail feature in that the
data between the device and the HP DSS server is encrypted. An rfc822-compliant e-mail
message that includes the scanned data as a MIME attachment is created in the folder
“\HPEMAIL2” in the HP DSS program directory on the HP DSS server. The third-party
software program, which is monitoring this folder, processes the e-mail message and sends
it out in a secure manner.
ENWW
Using the Digital Sending Software
13
The Secondary E-mail tab contains settings for the secure e-mail option.
1. To enable the Secondary E-mail option, select the Enable Send to Secondary E-mail
check box.
2. The name of this feature can be altered to more closely reflect the third-party program's
functionality (such as Secure or Encrypted E-mail). The name provided here will be
displayed on the digital sender's control panel home screen. Use the Home Screen
Display Name field to specify the display name. Type a custom display name into the
Home Screen Display Name box or select from one of the following options:
●
●
●
Secondary E-mail
Secure E-mail
Specialized E-mail
3. Click the Advanced... button on this tab to specify any X-Headers that you want to
include in the e-mails.
X-Headers provide the administrator with the capability of providing a user-defined
header that will be inserted in the rfc822 file for each Secondary E-mail message sent by
the digital sender. The third-party e-mail software program can then perform actions
based on this header information.
Click the Help button to get more information about this tab.
NOTE
Authentication tab
Use the Authentication tab to control how users are authenticated when using the digital-
sending features. Authentication is an important security feature of the digital sender. It is
highly recommended that you enable authentication on the digital sender in order to prevent
unauthorized use.
14
Chapter 2 Configuring HP DSS
ENWW
Authentication consists of two interdependent parts. First, the device verifies the user’s
credentials by using the selected authentication method. Then, the device attempts to find
the user’s e-mail address in the database of an LDAP server by using settings specific to
your LDAP server. If either step fails, the user is denied access to the digital-sending
features. These two steps utilize two distinct technologies (an authentication server and an
LDAP server), except in the case of the LDAP server method, where both steps are
accomplished by using the LDAP server.
To enable authentication, start by selecting an option from the Authentication Method drop-
down list. The following options are available.
●
●
●
●
●
None
Microsoft® Windows
LDAP server
Novell NDS (if Novell client software is present)
Novell Bindery (if Novell client software is present)
LDAP Configuration
After you select the authentication method on the Authentication tab, the LDAP
configuration settings appear. The device uses LDAP to retrieve the e-mail address for the
authenticated user. After the user has provided valid credentials, the software uses this
information to match an attribute in the LDAP database. After the match is made, and the
user is identified in the database, the user’s e-mail address is retrieved by using another
database attribute. The LDAP settings include the following options.
●
●
Options for configuring HP DSS to gain access to the LDAP server
Options for searching the database to obtain user e-mail addresses
ENWW
Using the Digital Sending Software
15
To configure the LDAP server
4
5
1
1. Click the Find Servers button. The program searches the network for LDAP servers,
and might also prompt you for your network username and password, depending on
your network configuration. Next, the Select LDAP Server dialog box appears,
containing a list of LDAP servers on the network.
2. Select the LDAP server that you want to use. The information about the selected server
appears.
3. Click OK to accept the selected server. The server information is filled in on the
Authentication tab.
4. Click Find Settings. The server settings appear in a dialog box. Click Yes to accept the
settings.
5. Click the Test button on the Authentication tab to test the settings. In the Test User
Authentication dialog box, type in the network logon credentials of a user in order to
test wether LDAP can successfully retrieve an e-mail address.
If the Find Servers process fails to find any LDAP server, you can type the host name or IP
address of the LDAP server directly into the LDAP Server text box, and then use the Find
servers for more information, and if you are unable to communicate with the LDAP server,
contact your network administrator for help with troubleshooting.
NOTE
NOTE
Click the Help button to get more information about this tab.
Fax tab
If this feature is enabled, users can send faxes directly from the device. They can select
destinations from an address book if one is loaded, or type fax numbers in at the control
panel. The same document can be sent to multiple fax numbers.
16
Chapter 2 Configuring HP DSS
ENWW
The configuration program Fax tab controls all of the HP DSS fax settings.
To configure the fax option, first select the fax delivery method from the Faxing Method
drop-down list. The following options are available.
●
●
●
●
None
LAN Fax
Internet Fax
MS Windows 2000 Fax
Depending on which method is selected, the applicable settings appear on the Fax tab. Fill
in these settings to complete the fax configuration process.
To set up a LAN fax service
Follow these instructions to set up faxing from the digital sender by using your network's
LAN fax service.
1. Select LanFax from the drop-down list on the Fax tab.
2. Select your LAN fax software product name from the Product Name drop-down box.
3. Click the Advanced button to set up input and output settings for your LAN fax product.
4. Use the Browse button to select the network folder that your fax software uses.
5. Fill in the Credentials to Access Folder section, if required. Use the Verify Folder
Access button to test the credentials and make sure that you have access to the folder.
6. Click Apply to save the LAN fax settings.
ENWW
Using the Digital Sending Software
17
To set up an Internet fax service
With an Internet fax service, faxes are sent by e-mail. When using HP DSS, the user
specifies a fax number at the device, and then the software creates and sends the e-mail
behind the scenes.
1. Select Internet Fax from the drop-down list on the Fax tab.
2. Type the domain name for your Internet fax provider into the Fax Provider Domain text
box, for example, efax.com. HP DSS takes the phone number that is typed at the
device and then uses this domain name to create the e-mail, for example, [phone
number]@efax.com.
3. Type a valid e-mail address into the Default Fax Account e-mail address text box. The
fax service uses this e-mail address for billing purposes and for any returned or failed
Internet fax e-mail.
4. Select the check box if you want HP DSS to use the authenticated user's e-mail address
as the return e-mail address.
5. Click Apply to save the Internet fax settings.
To set up a Windows 2000 fax service
In order to use the Windows 2000 fax service, you must have a fax modem installed on the
HP DSS server.
1. Select MS Windows 2000 Fax from the drop-down list on the Fax tab.
2. Click the Fax Properties button. The Windows Fax Console dialog box appears. Use
the Tools menu to configure any settings, if needed.
3. Click Apply to save the Windows 2000 fax settings.
Click the Help button to get more information about the Fax tab.
NOTE
18
Chapter 2 Configuring HP DSS
ENWW
To add folders to the Folders list
1. Click Add… to add a new folder. The Add Predefined Folder dialog box appears.
2. Type a name for the folder into the Alias Name text box. This name appears in the
device control-panel interface.
20
Chapter 2 Configuring HP DSS
ENWW
3. Click Browse… to browse to a folder location, and then click OK to accept it.
Supported operating systems for folder destinations are Windows 98, Windows NT,
Windows 2000, Windows XP, Windows Server 2003, and Novell NetWare.
NOTE
4. Select the credentials that you want to use for access to the folder from the Access
Credentials drop-down list. If Public is selected, the program uses the Credentials to
Access Public Folders from the Folders tab. If MFP User is selected, the program
uses the credentials with which the user has logged into the device.
5. Click OK to save the settings. The new folder is added to the list.
6. Repeat steps 1 through 5 to add more folders.
7. Type in the public access credentials that are required for access to folders in the
Credentials to Access Public Folders area of the Folders tab. This information is
required before you can save the folder list.
8. Click Apply to save the new folders.
Click the Help button to get more information about this tab.
NOTE
Workflows tab
With workflows, users can scan a document and send it to a custom workflow destination.
The workflow feature gives users the ability to send additional information in the form of a file
that is saved with the scanned document in a specified network or FTP location. Prompts at
the control panel are used to collect specific information. A third-party software program
monitoring the network folder or FTP site can then retrieve and decipher the information,
performing the specified operation on the scanned image. You can also set up a printer as a
workflow destination, which allows users to scan a document and then send it directly to a
network printer to be printed.
ENWW
Using the Digital Sending Software
21
Use the Workflows tab to set up workflow processes for use with third-party software
programs. To enable this feature, first select the Enable Workflows check box at the top of
the tab.
Creating a workflow process consists of three parts:
●
The workflow group, which defines which workflow menus and forms will be available on
the control panel of the digital sender.
●
●
The workflow menu, which creates logical groups of workflow forms.
The workflow form, which collects information entered by the user at the control panel
before initiating a send-to-workflow job.
To create a workflow group
1. Click the Add Group button. The Workflow Group dialog box appears.
2. Type the name of the new group. The name must be unique.
3. Click OK to save the new group.
22
Chapter 2 Configuring HP DSS
ENWW
To create a workflow menu
1. In the workflow tree, select the group that you just created.
2. Click the Add Menu button. The Workflow Menu dialog box appears.
3. Type the name of the new menu. This name must be unique within the workflow group.
ENWW
Using the Digital Sending Software
23
4. Select the style of the workflow menu. The style determines which options are available
for workflow forms within this workflow menu. The only available choice is Enhanced.
5. Click OK to save the new workflow menu.
To create a workflow form
1. Select the workflow menu that you just created.
2. Click the Add Form button. The Workflow Form dialog box appears.
24
Chapter 2 Configuring HP DSS
ENWW
3. Type a name for the new form into the Form Name text box.
4. Select the destination type from the Destination Type drop-down list. The options are
Folder, FTP Site, and Printer.
Based on the option that you select, the options on the Workflow Form dialog box change.
The remainder of this procedure applies to the Folder option. See the following sections, To
for creating a workflow form for an FTP site or a printer.
NOTE
5. Type the path for the destination folder in the Folder Path text box, or use the browse
button to select a path.
6. Select the access method for the folder from the Access Credentials drop-down list.
The choices are "Public" and "MFP User." If MFP User is selected, HP DSS uses the
credentials of the user that is logged in to the device. If Public is selected, HP DSS uses
the Credentials to Access Public Folders that are specified on the main Workflows
tab.
7. Under Image File Settings, select the settings for the scanned file. These should be the
settings that are required by the third-party software program that processes the file.
8. Select the file type for the metadata file from the File Format drop-down list. The options
are None, .HPS, or .XML. This is the file that contains the data that the workflow
prompts collect. If you are not creating any prompts, you can select None.
9. Select the Generate OCR File check box under OCR Settings if the processing
software program needs an OCR (optical character recognition) file. Click the Settings
button to specify the OCR settings for language and output file format.
10. In the Prompts area, you can define prompts and expected responses for the user of
the workflow form. The prompts appear on the device control panel. The responses to
the prompts are saved in the metadata file, which is stored with the document image for
use by the third-party workflow software program.
ENWW
Using the Digital Sending Software
25
Follow these instructions to add prompts.
a. Click the Add button to add prompts.
b. In the Add Prompts dialog box, click the New button to create a new prompt. This
opens the Workflow Prompt dialog box.
c. Under Prompt Settings in the Workflow Prompt dialog box, type the Prompt
Name, the Prompt Text, and any Help Text for the prompt. The Help text appears if
the user touches the HELP button on the digital-sender control panel while the prompt
is on the screen.
d. Under Response Settings, select the Response Format. The Response Format
options are String, Numeric, Date, Time, or Privacy.
The Privacy response format uses asterisks (*) to hide what the user types in on the control
panel. This response type can be used for private information such as a password or an
employee number.
NOTE
e. Under Response Type, select User Editable or Selection List. If User Editable is
selected, you can select the User must supply a response check box to require a
response.
f. If applicable, type a default response in the Default Response text box. The
program uses the default response if the user does not provide a response to the
prompt.
g. Click OK to save the prompt settings. The new prompt is added to the Prompts List
in the Add Prompts dialog box.
h. Repeat steps b through g as needed to create more prompts.
i. After creating all of the required prompts, you can use the Move buttons at the
bottom of the list to adjust the order of the prompts.
j. Click OK to accept the new set of prompts. The new prompts appear in the Prompts
area of the Workflow Form dialog box.
11. Click OK to accept all of the settings on the Workflow Form dialog box. The new form
appears in the workflows list on the Workflows tab.
A workflow form can be edited at any time by selecting it and then clicking the Properties
NOTE
button.
12. Type the public access credentials for access to workflow folders in the Credentials to
Access Public Folders area of the Workflow tab. This information is required before
you can save the workflow settings.
13. Click Apply to save the new workflow settings.
26
Chapter 2 Configuring HP DSS
ENWW
To create a workflow form for an FTP site
1. In the Workflow Form dialog box, select FTP Site in the Destination Type drop-down
box.
2. Type the host name or IP address of the FTP server into the FTP Server text box.
3. Click the Credentials button, and then type in the user name and password that are
required for the FTP server. Click OK to save the credentials.
4. In the FTP Path text box, type in the path to the directory on the FTP server that you
want to use for the scanned documents.
5. Follow Steps 7 through 11 in the previous procedure to complete the remainder of the
workflow form settings and add any prompts.
ENWW
Using the Digital Sending Software
27
To create a workflow for a printer
You can use a workflow form to send a scanned document to a network printer to be printed.
1. In the Workflow Form dialog box, select Printer in the Destination Type drop-down
box.
2. Select a printer from the Select Printer drop-down box, which lists the available network
printers.
3. Select one of the radio buttons to use the default or custom printer preferences. If you
select custom printer preferences, click the Preferences button to set them up.
4. Click OK to save the workflow form.
5. Click Apply to save the settings on the Workflow tab.
Click the Help button on the Workflows tab or any of the workflow dialog boxes to get more
NOTE
information.
Addressing tab
Use the Addressing tab to configure HP DSS to make centralized address books available
to digital-sender users.
28
Chapter 2 Configuring HP DSS
ENWW
LDAP directory replication
An address book is available on the digital sender to speed up the process of selecting
e-mail and fax destinations from the control panel. The e-mail addresses and fax numbers in
the address book come from several sources:
●
●
●
The LDAP server on the network
Destinations previously specified by users at the control panel
E-mail and fax address books created with the HP Address Book Manager
You can use one of two methods to synchronize the digital-sender address books with the
LDAP server.
Method
Description
Effect at the control panel
Using a replicated LDAP
address book
HP DSS takes a snapshot of
the LDAP server’s database
and populates the digital
sender's address book with the
addresses that it finds. The HP
MFP DSS Configuration Utility
can be used to either manually
As you type the initial
characters in a name, the
digital sender attempts to
complete the name from the
names in the address book.
You type more characters until
a match is found. When you
initiate the task or schedule it to select a name, the associated
run automatically at a certain
time.
e-mail address is automatically
selected.
Using an LDAP address book
directly
Firmware in the digital sender
initiates and resolves name
queries directly with the LDAP
server. You do not have to
synchronize the address book
with the LDAP server, either
manually or according to a
schedule.
You type a partial name. The
digital sender displays the list
of resulting names from the
LDAP server. When you select
a name, the associated e-mail
address is automatically
selected.
If the digital sender is configured to use an LDAP address book directly, it cannot access the
replicated address book.
NOTE
If replication is enabled, only the display names and e-mail addresses are replicated.
ENWW
Using the Digital Sending Software
29
To set up automatic replication of the LDAP address book
1. Click the Settings... button. The Replicating LDAP Address Book dialog box appears.
2. Select the Enable LDAP Directory Replication check box.
3. On the LDAP Settings tab, set up the necessary parameters for logging into the LDAP
information. After setting up the LDAP parameters, you can also click the Advanced
button to set up more advanced LDAP search options.
4. On the Replication tab, select the schedule for replicating the LDAP database. If you
select Daily, Weekly, or Monthly, you can set a specific time and day of the week for
the replication process.
Personal address books
Select the Enable PABs check box to enable users to use their personal address books to
address e-mail on the digital sender. Personal address book support is only available if
authentication is enabled and the authentication method is set to Microsoft Windows (see
Authentication tab). The Microsoft Messaging API (MAPI) is also required to interface with a
user's personal address book. Make sure that the Windows Messaging Component is
installed. If you have a MAPI client software program installed (such as Microsoft Outlook),
this component should already be in place.
30
Chapter 2 Configuring HP DSS
ENWW
DSS address books
HP DSS uses address books to store e-mail addresses that a user types at the device. If
user authentication is enabled on the device, addresses are stored in a user's individual
HP DSS address book. Otherwise, the addresses are stored in a public HP DSS address
book. HP DSS address books are available to every digital sender or MFP that HP DSS
supports. If the addresses that are contained in these address books are no longer needed,
you can clear out any or all of the HP DSS address books by clicking the Clear button in the
DSS Address Books section of the Addressing tab. This displays a list of any existing
address books.
Click the Help button to get more information about the Addressing tab.
NOTE
Preferences tab
The Preferences tab specifies the path for the HP DSS temporary files. These files can be
very large, so you should select a location that has sufficient disk space. Click the Browse...
button to select a location.
Click Apply to save the new folder path if you change it.
Click the Help button to get more information about this tab.
NOTE
ENWW
Using the Digital Sending Software
31
MFP Configuration tab
The MFP Configuration tab specifies which digital senders and MFPs are using the
HP DSS service, and also provides an interface for customizing HP DSS features for specific
digital-sending devices.
MFP Configuration tab
1
2
3
MFP list
Configure MFP button
Add button
32
Chapter 2 Configuring HP DSS
ENWW
To add a new digital sender or MFP
1. Click the Add... button near the bottom of the tab. The Add MFPs dialog box appears.
2. Click the Find MFPs button to find all of the MFPs and digital senders on the network.
Select the device you want to add from the list that appears.
If you know the hostname or IP address of the device, you can type it in the Hostname or IP
Address text box under Manually enter an MFP's network name rather than using the
Find MFPs button.
NOTE
3. If you want the device that you are adding to use the same settings as a previously
configured device, select the previously configured device from the When adding new
MFPs copy settings from drop-down list.
4. Click the Add--> button to add the device to the MFP List.
You can only add as many digital senders or MFPs as you have "seats" available in your HP
DSS license. Near the top of the Add MFPs dialog box you can see how many seats you
have available.
NOTE
5. Click Close to close the Add MFPs window.
ENWW
Using the Digital Sending Software
33
To configure an individual digital sender or MFP
1. Select the digital sender or MFP from the list on the MFP Configuration tab.
2. Click the Configure MFP... button. The dialog box that appears looks similar to the main
Configuration program interface. Use this interface to customize the specific digital-send
settings for this device. Settings that are specified on these tabs override the settings
that are made on the general HP DSS Configuration program tabs.
You must use this interface to enable the digital sending features for the individual devices.
Even if a feature is enabled on the HP DSS configuration tabs, it is not enabled on the
device until it has been enabled in the Configure MFPs interface.
NOTE
3. On the Authentication tab, select the Enable Authentication check box to enable
authentication for the selected device. Select the check boxes next to the features that
you are enabling. This requires the user to log in before using that feature. Select the
network domain from the Default Domain drop-down box.
4. On the Send to Email tab, select the Enable Send to Email check box, and select via
the Digital Sender service in the Send Emails drop-down list.
5. If you would like the users to be able to add their own e-mail message when sending
e-mail, click the Advanced button and select the Editable by user check box.
6. On the Addressing tab, select the Allow MFP to directly access an LDAP Address
Book check box if you want HP DSS to retrieve e-mail addresses directly from an LDAP
server. Select the previously-configured LDAP server in the LDAP Server drop-down list.
7. On the Send to Email (2) tab, select the Enable Send to Secondary Email check box
if you are using the secondary e-mail feature. Select the display name for the secondary
e-mail service from the Home Screen Display Name drop-down list.
8. On the Send to Fax tab, select the Enable Send to Fax check box if you are using the
fax feature. Make sure that via the Digital Sending service is selected in the Send
Faxes drop-down list.
9. On the Send to Folder tab, select the Enable Send to Folder check box if you are
using this feature.
10. On the Send to Workflows tab, select the Enable Send to Workflows check box if you
are using workflows. In the Workflow Group drop-down box, select the group that
contains the workflow menu and form that you want to use for this device.
11. Click OK to save all of the changes.
12. Click Apply to update the MFP Configuration settings.
The settings are not propagated to the digital sender until you click the Apply button.
NOTE
To configure a group of digital senders or MFPs
If you need to configure a group of digital senders or MFPs, you can configure them all at
one time rather than one by one. To do this, hold down the Shift key or Ctrl key on your
keyboard and then click on the devices you want to configure on the MFP Configuration
tab. Then click Configure MFP to configure the entire group.
The devices you select must all be of the same type. For example, they must be all digital
senders, or all MFPs of a specific model type.
NOTE
34
Chapter 2 Configuring HP DSS
ENWW
Click the Help button to get more information about the MFP Configuration tab.
NOTE
Log tab
The Log tab shows the HP DSS activity log. This log contains all of the activities that the HP
DSS service performs. The following information is included in the list for each log entry:
●
●
●
Severity
Event
Date and Time
Click the Details button to open a Details dialog box that provides additional information
about the selected log event.
Click the Help button to get more information about this tab.
NOTE
NOTE
About tab
The About tab provides HP DSS version information.
Click the Help button to get more information about this tab.
Testing the configuration
After configuring all of the digital-sending features, you should test them on the digital
sender. Verify that all of the enabled options appear on the digital-sender control-panel
display. Then try each option to make sure that the document is successfully delivered to the
correct location.
Uninstalling the software
Uninstall the HP DSS service software by using one of the following procedures.
To uninstall the software with the uninstall program
To uninstall the software from Windows 2000 or XP, you must log on with administrator
privileges.
NOTE
1. Close all of the open programs.
2. On the Start menu, point to Programs, point to Hewlett-Packard, point to HP MFP
Digital Sending Software, and then click Uninstall.
ENWW
Uninstalling the software
35
3. In the Confirm Uninstall dialog box, click OK.
4. The uninstall process removes the program from your computer. At the end of the
process, you might have to restart your computer.
To uninstall the software with Add or Remove Programs
An alternate method for uninstalling the digital sender software is to use the Windows Add
or Remove Programs method.
1. Click Start, point to Settings, and then click Control Panel.
2. Click Add or Remove Programs.
3. Scroll through the list of software programs and click HP MFP Digital Sending Software.
4. Click Remove.
36
Chapter 2 Configuring HP DSS
ENWW
Administering the digital sender
3
This section provides information about the tools that you can use to administer the digital
sender.
Using the embedded Web server and HP Web Jetadmin
The embedded Web server (EWS) and HP Web Jetadmin are two online tools that can be
used to remotely administer the device.
The embedded Web server
This digital sender is equipped with an embedded Web server, which provides access to
information about digital sending and network activities. When a Web server is "embedded,"
that means that it resides on a hardware device (such as a digital sender) in the firmware,
rather than as software that is loaded on a network server. The advantage of an embedded
Web server is that it provides an interface to the device that anyone who has a network-
connected computer and a standard Web browser can use. You do not need to install or
configure any special software.
Features
Use the EWS to view the digital sender and network status and to manage digital sending
functions from your computer. With the EWS, you can complete the following tasks:
●
●
●
●
●
●
●
●
View digital-sender status information
Determine the remaining life on the ADF Maintenance Kit
View the control-panel menu configuration
View device configuration reports
Receive notification of digital-sender events
Add or customize links to other Web sites
Select the language in which to show the embedded Web server pages
View and change network configuration
ENWW
Using the embedded Web server and HP Web Jetadmin
37
To view the EWS Web pages
To view the EWS Web pages, you need to have the device's IP address. You can find the IP
address in one of the two following ways:
●
Go to the digital sender and look at the upper-left corner of the touchscreen. Next to the
word Ready the IP address should appear.
●
If the IP address does not appear on the touchscreen, press the MENU button on the
control panel. Touch the INFORMATION menu, and then touch CONFIGURATION. The
digital-sender configuration information appears on the touchscreen. Touch the OK
button to see the Jetdirect data. Scroll through the information until you find the IP
address.
Open a Web browser and type the digital sender's IP address into the Address box to open
the EWS Web page.
You can gain access to the embedded Web server from any operating system that supports
the TCP/IP protocol and a Web browser, preferably either Netscape Navigator 4.7x or
Microsoft Internet Explorer 5.0x or later. You cannot view the embedded Web server pages
from outside a firewall.
NOTE
Information pages
The pages on the Information tab of the embedded Web server provide status information
for the digital sender.
●
●
Device Status page—This page shows the status message that currently appears on
the device control panel.
Configuration page—The digital-sender Configuration page lists device information
that includes the serial number, and other information about the device. It also has an
Options list that lists options that are installed in each DIMM slot, CompactFlash slot,
and EIO slot. The Memory section of the page lists the digital-sender memory (RAM)
information, and the Security section lists the status of the security features.
●
●
●
Supplies Status page—This page shows the status of the ADF Maintenance Kit, and
indicates how soon it needs to be replaced.
Usage page—This page shows how many pages have been scanned by the device and
how many pages have been scanned with the ADF and the flatbed.
Device Information page—This page lists the device name for network management
needs, and shows the IP address for the device.
The device name can be edited on the Settings tab.
NOTE
●
Control Panel page—The Control Panel page shows a snapshot of the current state of
the control panel. Click the Refresh Image button to refresh the snapshot.
38
Chapter 3 Administering the digital sender
ENWW
Settings pages
The pages on the Settings tab of the EWS contain a variety of digital-sender settings.
●
Configure Device page—The options on this page are the same as some of the menus
on the device control panel. Use this page to configure some of the digital-sending
options.
●
●
E-mail Server page—Use this page to set up the SMTP server that should be used to
send digital sender e-mail alerts (set up on the Alerts page).
Alerts page—Use this page to set up e-mail alerts for many digital-sender events.
These alerts can be sent to a list of up to 20 e-mail, mobile device, or Web site
destinations.
●
●
AutoSend page—Use the AutoSend screen to send product-configuration and usage
information periodically to your service provider. This feature establishes a relationship
with Hewlett-Packard Company or another service provider to provide you with services
that include support agreements and usage tracking.
Security page—Use the Security page to set up a password to prevent unauthorized
users from gaining access to device configuration settings. After a password has been
set, any user opening the EWS Web page only sees the Information tab. To view the
other tabs, you must click the Log In link in the upper right corner of the screen and log
in using the password.
For security reasons, it is strongly recommended that you set up a password to protect the
digital sender EWS. This prevents unauthorized users from making configuration changes.
NOTE
●
●
Edit Other Links page—Use this page to add links to the Other Links box, which
appears in the lower-left corner of the EWS Web pages.
Device Information page—Use this page to change the device name, asset number,
and company contact information.
●
●
●
Language page—Use this page to specify the language that the EWS Web pages use.
Date and Time page—Use this page to set the correct date and time for the device.
Wake Time page—Wake Time can be set to wake the product up at a certain time on a
daily basis. There can only be one wakeup setting per day; however, each day can have
a different wakeup time. The sleep mode delay can also be set on this page.
Digital sending pages
The pages on the Digital Sending tab of the EWS control configuration of the digital-
sending features. Because the digital sender uses the HP DSS service to carry out its digital
sending tasks, it must be configured by using the HP MFP DSS Configuration Utility. This
centralizes configuration tasks and helps control security. Therefore, you do not have access
to any of the configuration settings on the Digital Sending tab as long as the digital sender
is using the HP DSS service.
ENWW
Using the embedded Web server and HP Web Jetadmin
39
Networking pages
The pages on the Networking tab of the EWS provide information about the digital sender
HP Jetdirect Inside embedded network connection and contain tools that you can use to
configure some specific network settings.
HP Web Jetadmin
HP Web Jetadmin is a server-based online tool that system administrators can use to
configure all of the printers and digital senders on their network. If you have a number of HP
digital senders and printers, this is a useful tool for controlling and configuring them as a
group rather than one by one. For supported host systems and available languages, and to
40
Chapter 3 Administering the digital sender
ENWW
Using the control-panel menus
The control-panel menus provide access to a wide variety of digital-sender settings. Some
configuration settings can only be changed by using the control-panel menus.
To view the control-panel menus, push the MENU button on the control panel.
Information menu
Use the Information menu to view some digital-sender configuration and statistical
information.
Item
Explanation
SHOW CONFIGURATION
Shows the configuration information for the
device. Click OK at the bottom of this screen to
see the EIO/HP Jetdirect information.
SUPPLIES STATUS
SHOW USAGE
Shows the remaining life for the ADF
Shows usage statistics for the number of pages
that have passed through the ADF and the
number of scans that have been done.
To view these reports in a printable format, open them by using the EWS Web pages. See
Information pages in the EWS section.
NOTE
Configure Device menu
The administrator can use the control-panel Configure Device menu to configure the device
directly from the control panel. This menu contains the following submenus:
●
●
●
●
●
●
●
Originals
Enhancement
Sending
System Setup
I/O
Resets
Security
Originals submenu
These settings control the default settings that describe the original document. The user can
change any of these settings at the time of scanning by using the control-panel interface.
ENWW
Using the control-panel menus
41
Item
Values
Explanation
PAPER SIZE
EXECUTIVE
LETTER
A4
Sets the paper size of the
original document.
The default setting is LETTER.
A5
LEGAL
B5 (JIS)
NUMBER OF SIDES
1
2
Indicates whether one side or
both sides of the original
document are scanned. If 2 is
selected, the ADF duplexer
scans both sides. Or, if the
original is placed on the glass,
the device prompts the user to
turn the page over after the first
side is scanned.
The default setting is 1.
ORIENTATION
PORTRAIT
Indicates whether the default
orientation of the content on
the original is portrait (short
edge at top) or landscape (long
edge at top).
LANDSCAPE
The default is PORTRAIT
CONTENT
TEXT
Describes the default content
type of the original. Select
PHOTO
MIXED
Photo if the original consists of
graphic images, or Text if the
image consists of text only.
Select Mixed if the original
contains both graphics and text.
The default setting is MIXED.
DENSITY
0 through 8
Specifies the default contrast
and brightness of the scanned
image. You can select from
nine increments:
0=lightest
8=darkest
The default setting is 4.
Enhancement submenu
These settings control the default settings for the enhancement options. The user can
change these settings at the time of scanning by using the control-panel interface.
42
Chapter 3 Administering the digital sender
ENWW
Item
Values
Explanation
SHARPNESS
0 through 4
Specifies the default sharpness
of the scanned image.
0=minimum sharpness
4=maximum sharpness
The default setting is 2.
BACKGROUND REMOVAL
0 through 8
Controls the default amount of
background material from the
original that is eliminated in the
scanned image. Background
removal is useful when you
scan both sides and do not
want the material on the first
side to be visible on the second
side.
0=minimum background
removal (more background is
visible)
8=maximum background
removal (less background is
visible)
The default setting is 2.
Sending submenu
These settings control the default settings for sending the scanned image. The user can
change the first four of these settings at the time of scanning by using the control-panel
interface. The remainder of these settings are for setting the SMTP and LDAP gateways
used by the device. It is recommended that these be set up with the HP MFP DSS
Configuration Utility rather than at the control panel.
Item
Values or submenu items
SCAN PREFERENCE
Explanation
E-MAIL
Determines whether the
document is scanned in color
or black and white.
The default setting is COLOR.
ENWW
Using the control-panel menus
43
Item
Values or submenu items
FILE TYPE
Explanation
E-MAIL (cont.)
Specifies the default file format
of the e-mail attachment.
●
●
●
●
.PDF
.TIFF
.MTIFF
.JPEG
The default setting is PDF.
FILE SIZE
Specifies the default
compression of the file, which
determines the file size.
●
●
●
SMALL
STANDARD
LARGE
The default setting is
STANDARD.
RESOLUTION
Specifies the default resolution
of the scanned image. A lower
dpi results in a smaller file size,
but image quality is affected.
●
●
●
●
75 DPI
150 DPI
200 DPI
300 DPI
The default setting is 150 DPI
ADDRESS VALIDATION
FIND SEND GATEWAYS
Enables the device to validate
e-mail syntax. Valid e-mail
addresses require the @ sign
and a period (".").
The default setting is ON.
The device searches the
network for SMTP and LDAP
gateways that it can use to
send e-mail.
SMTP GATEWAY
LDAP GATEWAY
The IP address of the SMTP
server used to send e-mail.
The IP address of the LDAP
gateway that is being used for
looking up e-mail address
information.
TEST SEND GATEWAYS
Tests the configured gateways
to see if they are functional.
44
Chapter 3 Administering the digital sender
ENWW
Item
Values or submenu items
LDAP SETTINGS
Explanation
E-MAIL (cont.)
These are the settings that are
necessary for contacting the
LDAP server. The settings
include the following items:
●
●
●
●
LDAP Search Root
LDAP Logon Method
LDAP Username
LDAP Password
REPLICATE MFP
None
This item copies the local Send
settings from one MFP or
digital sender to another. This
menu item only appears if the
digital sender is not connected
to the HP DSS service. Send
settings can also only be
copied to devices that are not
using the HP DSS service.
Gateway and LDAP settings are generally set up by using the HP DSS Configuration
NOTE
System setup submenu
These settings control the digital-sender system configuration.
Item
Values or submenu items
Explanation
DATE/TIME
DATE FORMAT
DATE
Sets the format of the date and
time and presents a wizard
interface to set the current date
and time.
TIME FORMAT
TIME
SHOW ADDRESS
AUTO
OFF
Controls whether or not the
device IP address appears on
the home screen (next to
"Ready").
The default setting is AUTO.
ENWW
Using the control-panel menus
45
Item
Values or submenu items
Explanation
SLEEP DELAY
1 MINUTE
Sets how long the device
remains idle before it enters
Sleep mode. Sleep mode
minimizes the amount of power
that the device consumes when
it is idle, and reduces wear on
the digital-sender electronic
components (by turning off the
display backlight).
15 MINUTES
30 MINUTES
45 MINUTES
60 MINUTES
90 MINUTES
2 HOURS
The default setting is 60
MINUTES.
4 HOURS
SEND SETTINGS
INACTIVITY TIME OUT
This is the amount of time
before the device resets to
default settings after a period of
inactivity on the control panel. It
is a range from 10 to 300
seconds.
The default setting is 60.
AUTO SETTINGS RESET
TIMEOUT AFTER SEND
Controls whether or not the
device automatically resets to
default settings as soon as the
user initiates a job.
The default setting is OFF.
This is the length of time after
the user initiates a send job
that the device waits before it
returns to its default settings. It
is a range from 10 to 300
seconds.
The default setting is 10.
SCAN AHEAD
A send job can be scanned
even if the device is busy
sending another job. The job is
scanned and held until it can
be sent.
The default setting is ON.
AUDIBLE FEEDBACK
Controls whether or not the
control panel provides a sound
when the user selects an item.
The default setting is ON.
46
Chapter 3 Administering the digital sender
ENWW
Item
Values or submenu items
Explanation
WAKE TIME
MONDAY
Sets the time that the device
automatically comes out of
Sleep mode. This feature can
be set for a different time for
each day of the week. This
setting is off by default.
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
SUNDAY
LANGUAGE
A list of the available control-
panel languages appears.
Sets the language of the
control panel.
The default setting is ENGLISH.
I/O submenu
These settings control the input and output port configuration.
Item
Values or submenu items
Explanation
I/O TIMEOUT
5 to 300
Use this to select the Input/
Output (I/O) timeout period in
seconds. The I/O timeout refers
to the time that the device waits
before ending a job.
The default setting is 15.
FIND SEND GATEWAYS
SMTP GATEWAY
None
Initiates a search to find a valid
SMTP server and a valid LDAP
server on the network.
IP address
IP address
The IP address of the SMTP
server that processes the
e-mail sent by the digital sender.
LDAP GATEWAY
The IP address of the LDAP
server that provides the
address book for the e-mail
service.
EMBEDDED JETDIRECT
MENU
See the following table.
This submenu contains all of
the device network settings.
EIO 1 ENU
NOVELL
DLC/LLC
IPX/SPX
TCP/IP
This menu does not appear
unless you have a card
installed in the EIO slot. This
menu controls the
communication protocols for
the EIO card. The actual
content of the EIO menu
depends on the card that is
installed.
ETALK
ENWW
Using the control-panel menus
47
Item
Values or submenu items
Explanation
TEST SEND GATEWAYS
None
This tests the configured SMTP
and LDAP gateways to see if
they are functional.
Embedded Jetdirect submenu
The Embedded Jetdirect submenu under the I/O menu contains all of the digital-sender
network settings.
Item
Options
Values
Explanation
TCP/IP
ENABLE
ON
Use this item to enable or
disable the TCP/IP protocol.
OFF
HOST NAME
None
This is an alphanumeric
string, up to 32 characters,
that identifies the device. This
name is listed on the Jetdirect
configuration page. The
default host name is
NPIxxxxxx, where xxxxxx is
the last six digits of the LAN
hardware (MAC) address.
48
Chapter 3 Administering the digital sender
ENWW
Item
Options
Values
Explanation
TCP/IP (cont.)
CONFIG METHOD
BOOTP
DHCP
Use BOOTP (Bootstrap
Protocol) for automatic
configuration from a BootP
server.
AUTO IP
MANUAL
Use DHCP (dynamic host
configuration protocol) for
automatic configuration from
a DHCP server. If this option
is selected and a DHCP lease
exists, the DHCP RELEASE
and DHCP RENEW menu
items are available to set
DHCP lease options.
Select AUTO IP to use
automatic link-local IP
addressing. An address in the
form 169.254.x.x is
automatically assigned.
If you select Manual, use the
MANUAL SETTINGS menu
to configure the TCP/IP
parameters.
DHCP RELEASE
DHCP RENEW
NO (default)
YES
If you select NO, the current
DHCP lease is saved. If you
select YES, the current
DHCP lease along with the
leased IP address are
released.
NO (default)
YES
If you select NO, the device
does not request to renew the
DHCP lease. If you select
YES, the device requests to
renew the current DHCP
license.
MANUAL SETTINGS IP ADDRESS
SUBNET MASK
Fill in the network settings for
the device. The IDLE
TIMEOUT is the time period,
in seconds, after which an
idle TCP connection is
closed. The default is 270
seconds.
SYSLOG SERVER
DEFAULT GATEWAY
IDLE TIMEOUT
ENWW
Using the control-panel menus
49
Item
Options
Values
Explanation
TCP/IP (cont.)
DEFAULT IP
AUTO IP
LEGACY
If AUTO IP is selected, a link-
local IP address 169.254.x.x
is set. If LEGACY is selected,
the address 192.0.0.192 is
set, consistent with older
HP Jetdirect products.
PRIMARY DNS
None
None
Specify the IP address of the
primary Domain Name
System (DNS) server.
SECONDARY DNS
ENABLE
Specify the IP address of the
secondary DNS server.
IPX/SPX
ON
Enables or disables the IPX/
SPX protocol.
OFF
FRAME TYPE
AUTO
The AUTO selection
automatically sets and limits
the frame type to the first one
that is detected. Select AUTO
or one of the other frame type
selections for Ethernet
networks.
EN_8023
EN_11
EN_8022
EN_SNAP
APPLETALK
DLC/LLC
ENABLE
ENABLE
ON
Enables or disables the
Appletalk protocol.
OFF
ON
Enables or disables the DLC/
LLC protocol.
OFF
SECURE WEB
HTTPS REQUIRED
HTTPS OPTIONAL
None
The HTTPS REQUIRED
setting requires secure
HTTPS access to the
embedded Web server.
HTTPS OPTIONAL allows
either HTTP or HTTPS
access to the embedded Web
server.
50
Chapter 3 Administering the digital sender
ENWW
Item
Options
Values
Explanation
DIAGNOSTICS
LOOPBACK TEST
CAUTION
YES
NO
Select YES to initiate the
loopback test.
Loopback verifies that TCP/IP
is installed and correctly
configured on the local
device. If a reply is returned
then you know that the TCP/
IP stack is functioning
correctly.
This test erases
your TCP/IP
configuration.
PING TEST
DEST IP
Fill in each of the settings
before performing the ping
test. The ping test verifies
end-to-end connectivity by
sending an Internet Control
Message Protocol packet to
see if a destination host is
responding.
PACKET SIZE
TIMEOUT
COUNT
PRINT RESULTS
EXECUTE
DEST IP specifies the IP
address of the remote host.
PACKET SIZE specifies the
size of each packet, in bytes,
to be sent to the remote host.
The minimum (and default) is
64 and the maximum is 2048.
TIMEOUT specifies the
length of time, in seconds, to
wait for a response from the
remote host. The default is 1
and the maximum is 100.
COUNT specifies the number
of test packets to send for this
test. Select a value from 1 to
100. To configure the test to
run continuously, select 0.
The PRINT RESULTS option
does not apply to the digital
sender.
Select EXECUTE and then
select YES to initiate the ping
test.
ENWW
Using the control-panel menus
51
Item
Options
Values
Explanation
DIAGNOSTICS
(cont.)
PING RESULTS
PACKETS SENT
These menu items show the
results of the ping test.
PACKETS
RECEIVED
PACKETS SENT and
PACKETS RECEIVED show
the number of packets sent to
and received from the remote
host since the most recent
test was initiated or completed.
PERCENT LOST
RTT MIN
RTT MAX
RTT AVE
PERCENT LOST shows the
percent of ping test packets
that were sent with no
response from the remote
host.
PING IN PROCESS
REFRESH
RTT MIN, MAX and AVE list
the minimum, maximum and
average round-trip-time
(RTT), from 0 to 4096
milliseconds, for packet
transmission and response.
PING IN PROGRESS
indicates whether or not a
ping test is in progress.
Select REFRESH to update
the ping test data with current
results.
RESET SECURITY
LINK SPEED
NO
None
None
Sets the current security
settings back to the factory
defaults. Select YES to reset
the security settings.
YES
AUTO
Select AUTO to automatically
configure the device to match
the network's link speed. If
the Auto setting fails, it is set
to 100TX Half.
10T HALF
10 T FULL
100TX HALF
100TX FULL
If you would rather select the
link speed manually, select
one of the four options.
Resets submenu
This menu contains reset commands for some digital-sender settings.
52
Chapter 3 Administering the digital sender
ENWW
Item
Values
Explanation
RESTORE FACTORY
SETTINGS
None
This item resets the
parameters and the user-set
defaults to their factory
defaults. It also clears the input
buffer for the active I/O. This
reset should be used with
caution.
SLEEP MODE
OFF
ON
Use this setting to turn Sleep
Mode on and off. If Sleep Mode
is off the device never enters
power save mode.
The default setting is ON.
LOCK CARRIAGE
None
The Lock Carriage menu item
moves the carriage into a
position where it can be locked.
Select this menu item if you are
unable to engage the Scanner
Lock. See Parts of the digital
sender for the location of the
Scanner Lock.
CLEAR ADDRESS BOOK
None
This removes all addresses
from the local Address Book.
CLEAR DOCUMENT FEEDER NO
Use this menu item to clear the
Order Document Feeder Kit
and Replace Document
MESSAGE
YES
Feeder Kit warning messages.
The Order Document Feeder
Kit message appears
approximately one month
before the ADF kit needs to be
replaced. The Replace
Document Feeder Kit appears
at end of life (maintenance
interval). This menu item only
appears when one of the
messages has appeared on the
control panel. Set it to YES to
hide the warning message.
RESET SUPPLIES
NEW DOCUMENT FEEDER
KIT
This menu item resets the
Document Feeder Kit
maintenance interval after a
new kit has been installed. Set
this menu item to YES after
installing a new kit.
Diagnostics menu
The Diagnostics menu contains the following items.
ENWW
Using the control-panel menus
53
Item
Values or submenu items
Explanation
SHOW EVENT LOG
None
Selecting this item shows the
most recent events first, up to
the last 50 occurrences. The
log appears in the control-panel
display.
CALIBRATE SCANNER
SCANNER TESTS
None
Select this item to begin the
scanner calibration process.
instructions.
LOWER LAMP
These are tests to make sure
that the scanner components
are functioning correctly. In
most cases, the test turns on
the selected scanner
SENSORS
UPPER LAMP
SHUTTER SOLENOID
WEIGHT SOLENOID
ADF OUTPUT MOTOR
ADF INPUT MOTOR
ADF INPUT REVERSE
FLATBED MOTOR
ADF READ MOTOR
ADF READ MOTOR REVERSE
ADF DUPLEX SOLENOID
ADF LED INDICATOR
component and then asks the
user to verify that it is on.
CONTROL PANEL
LED'S
This test turns each LED on
and off in order to verify
functionality.
DISPLAY
Shows test patterns on the
display.
BUTTONS
Instructs you to press each
control-panel button and verify
its functionality.
TOUCHSCREEN
Divides the display into
squares of a grid. You are then
instructed to touch each square
and see if the touch was
detected.
Service menu
The Service menu is locked and can only be opened by a service technician.
54
Chapter 3 Administering the digital sender
ENWW
Controlling security
The most basic security feature of the digital sender is its ability to require a network login
before a user can gain access to digital sending functions. This prevents unauthorized users
from walking up to the device and sending documents. It is highly recommended that you
For users who are concerned about e-mail security, the digital sender comes with a secure
e-mail option. A number of third-party software vendors offer services for secure e-mail
delivery. The Secondary E-mail feature is designed to work with one of these third-party
software programs for users who require an extra measure of data security. It differs from
the regular e-mail feature in that the data between the device and the HP DSS server is
encrypted. An rfc822-compliant e-mail message that includes the scanned data as an
attachment is created in a folder on the HP DSS server. The third-party software program,
which is monitoring this folder, processes the e-mail message and sends it out in a secure
manner.
To restrict software access
In order to keep the digital sender secure, you must also restrict access to the software
programs that can be used to configure the device. By default, the digital-sending
configuration options in the embedded Web server (EWS) are disabled when the digital
sender begins using the HP DSS service. The digital sender can then only be configured by
using the HP MFP DSS Configuration Utility. This centralizes configuration tasks and helps
control security. You should make sure that the HP DSS is installed on a secure server and
that the HP MFP DSS Configuration Utility cannot be used by unauthorized users.
In addition, you can also set a password in EWS to prevent access to the device-settings
tabs. After the password has been set, users can only see the EWS Information tab. See
The final software program that can be used to control the digital sender is the HP Web
Jetadmin program. This program can also be configured to require a password before any
changes can be made. It should also be installed on a secure server and should be
protected from unauthorized use.
Security lock
The security lock is a mechanical lock that prevents the removal of internal device
components. The lock used is a third-party computer lock such as the ones that are used to
secure laptop computers. Purchase the lock separately, and then install it on the product in
the location shown in this figure.
ENWW
Controlling security
55
Working with address books
One of the roles of the digital-sender administrator is to maintain the public and private
address books on the device.
Clearing HP DSS Address Books
HP DSS uses address books to store e-mail addresses that a user types at the device. If
user authentication is enabled on the device, addresses are stored in a user's individual
HP DSS address book. Otherwise, the addresses are stored in a public HP DSS address
book. HP DSS address books are available to every digital sender or MFP that the HP DSS
server supports. If the addresses contained in these address books are no longer needed,
you can clear any or all of the HP DSS address books by clicking the Clear button on the
Addressing tab in the HP MFP DSS Configuration utility.
Authentication and address book availability
Addresses entered directly by the user are saved differently depending on whether the user
has been authenticated at the control panel.
●
●
Authenticated: Saved to a “Personal” address book.
Not Authenticated: Saved to a “Guest” address book. All non-authenticated users will
see the contents of the “Guest” address book.
●
●
E-mail addresses stored in Outlook contacts are available to the authenticated user.
E-mail addresses typed directly at the control panel are cached in a private address book.
Personal address books
HP DSS accesses an authenticated user’s personal e-mail addresses stored in their Outlook
contacts folder. The digital sender displays a list of personal e-mail addresses combined with
addresses from other available public address books.
Personal address book availability has the following requirements: Windows authentication
must be enabled on the digital sender (Novell is not supported), and the HP DSS server
must have an MAPI-compliant e-mail client installed.
NOTE
Local address book preservation
E-mail addresses typed directly at the control panel of a digital sender that is not connected
to HP DSS are stored in a local address book. When the digital sender is added to HP DSS,
the local address book is imported into a “Guest” address book stored on the HP DSS
server. This address book combines all of the address books of the digital senders and
MFPs that have been added, making previously cached email addresses available from any
digital sender or MFP.
56
Chapter 3 Administering the digital sender
ENWW
The digital sender control panel provides the user with a choice between two views of the
address book: “All” and “Personal.” The “Personal” view is provided when the user has been
authenticated. Each view presents to the user a single sorted list of e-mail addresses
merged from all address books currently active in that view. The following table shows which
of the address books are merged in each view.
Dynamic LDAP
Enabled
Authentication
Enabled
View “Local”
View “Personal”
No
No
Guest, Global
Guest
(Replicated LDAP/
ABM), Public
Distribution List
No
Yes
Private, Personal,
Personal Distribution
List, Guest, Global
(Replicated LDAP/
ABM), Public
Private, Personal,
Personal Distribution
List, Guest
Distribution List
Yes
Yes
No
Guest, Dynamic LDAP Guest
Yes
Private, Personal,
Personal Distribution
List, Guest, Dynamic
LDAP
Private, Personal,
Personal Distribution
List, Guest
Private
The Private address book is unique to each authenticated user and provides the user a
place to store (add and delete) e-mail addresses entered from the digital sender control
panel. The Private address book is accessible by the user from any digital sender or MFP
that is configured to use authentication for send-to-e-mail.
Personal
The Personal address book is unique to each authenticated user and is a copy of the user’s
Microsoft Exchange Contact database. The e-mail addresses from the user’s contact list are
loaded into the Personal address book and the contact lists are loaded into the Personal
distribution list. The loading of these addresses and lists are initiated when the user
becomes authenticated.
Personal distribution list
Personal distribution lists are named lists of e-mail addresses obtained from the Microsoft
Exchange Server as Contact Lists and maintained in the Personal address book.
Guest
The Guest address book provides unauthenticated users a place to store (add and delete)
email addresses entered from the digital sender control panel. The Guest address book is
accessible by all users from any digital sender or MFP that is configured to use the Digital
Send Service.
ENWW
Working with address books
57
Global (Replicated LDAP/ABM)
The digital sender can be configured to import address book records from an LDAP server.
The Global address book populated from LDAP is commonly referred to as Replicated LDAP.
The HP Address Book Manager software provides functionality to populate the Global
address book directly from user input or from files generated from other databases. See the
Address Book Manager section below.
Public distribution list
A Public distribution list is a named list of e-mail addresses created or imported by the
Address Book Manager and maintained in the Global address book.
Address Book Manager
The main purpose of the Address Book Manager is to give the administrator a way to create
and change the e-mail address books stored in the HP Digital Sending Software. You must
be an administrator to use the Address Book Manager.
Specifically, you can use the Address Book Manager to accomplish the following tasks:
●
●
View, add, change, and delete information in the public address books
View, add, change, and delete information in the private address books of authenticated
users
Address Book Manager must be installed separately. Insert the HP DSS program CD,
browse to the ABM folder and run SETUP.EXE.
NOTE
Follow these instructions to open the Address Book Manager:
1. From your computer, click Start, and then point to Programs. Point to Hewlett-
Packard, and then click HP Address Book Manager. The Address Book Manager
window appears.
2. In the Digital Sender name field, type the DNS name or IP address for the HP DSS
server, or choose a previously entered DNS name or IP address from the drop-down list.
3. In the User name field, type ADMINISTRATOR.
4. In the User password field, type your password (if one is required) and click OK. If all of
the information is valid, the ABM main window appears.
Using the activity log
The device keeps a record of all digital-sending events in an activity log. Up to 1,024 entries
are stored in the activity log. New events overwrite the oldest events.
Icons appear in the activity log to identify the type of message:
Information—No action required
58
Chapter 3 Administering the digital sender
ENWW
Warning—Indicates a failure of some kind that might require action.
Error—Indicates a problem that requires administrator intervention and possibly a call
to an HP-authorized dealer.
The following events are recorded in the device activity log:
●
●
●
●
●
Each digital sending job (for all types of destinations)
Success or failure of an activity
Shutdown and restart
Deletion of address book contents
System errors
The following information is recorded about each event:
●
●
●
●
User
Date and time
Time
Supplementary details (such as list of destinations, size and number of pages, and
format)
●
●
Description of event
Severity of event (information, warning, error)
Three different activity logs can be viewed:
●
The HP DSS server log—Open the HP MFP DSS Configuration program and click the
Log tab to see the HP DSS server log. This shows the activity log for the HP DSS
service. Clicking the Details button opens a Details dialog box that provides additional
information about the selected log event. Clicking the Clear button clears the log.
●
Digital-sender activity log—Open the HP MFP DSS Configuration program and click
the MFP Configuration tab. Select the digital sender in the MFP list, and then click
Configure MFP. Click the Log tab to see the activity log for the selected device. You
sender event log messages for an explanation of event log messages.
●
Control-panel event log—Press the MENU button on the control panel and then touch
the DIAGNOSTICS menu. Touch SHOW EVENT LOG. This shows the 50 most recent
events for this device.
Clearing the log is useful if you are troubleshooting problems. After you clear the log, entries
reflect only current conditions. Clearing the log is also useful when you have made major
configuration changes.
ENWW
Using the activity log
59
Upgrading the firmware
The HP 9200C Digital Sender features remote firmware update (RFU) capability. Use the
following steps for remotely upgrading digital-sender firmware. These steps are explained in
more detail in the following sections.
1. Determine the current level of firmware installed on the device.
2. Go to the Web site and find out whether a new version is available. If it is, download the
latest firmware to your computer.
3. Download the new firmware to the device.
Determining the current level of firmware
To determine the current level of firmware, view the configuration page on the digital-sender
control panel. To view the configuration page, follow these instructions.
1. On the control panel, press the MENU button to open the menus.
2. Select the INFORMATION menu.
3. Select VIEW CONFIGURATION.
4. Scroll to the configuration section marked Device Information to find the firmware date
code. The firmware date code looks something like this: 20030502 05.003.0
Downloading the new firmware from the HP Web site
To find the most recent firmware upgrade for the digital sender, go to http://www.hp.com/
go/9200c_firmware. This page also contains instructions for how to download the new
firmware version.
Download the new firmware version from the web site and then use one of the following
methods to update the digital sender firmware.
Using FTP to upgrade the firmware on a direct network
connection
The device must be in a "ready" state to receive an .RFU file update. Any jobs that are
ahead of the RFU job in the queue are completed before the update is processed.
The elapsed time for an update depends on the I/O transfer time, as well as the time that it
takes for the device to reinitialize. The I/O transfer time depends on a number of things,
including the speed of the host computer that is sending the update. If the remote firmware
update process is interrupted before the firmware is downloaded (while Receiving Upgrade
appears on the control-panel display), the firmware file must be sent again. If power is lost
during the flash DIMM update (while the Performing Upgrade message appears on the
control-panel display), the update is interrupted and the message Resend Upgrade appears
(in English only) on the control-panel display.
Follow these instructions to perform the upgrade by using FTP.
60
Chapter 3 Administering the digital sender
ENWW
The firmware update involves a change in the format of nonvolatile random-access memory
(NVRAM). Any menu settings that are changed from the default settings might return to
default settings and must be changed again if you want settings that are different from the
defaults.
NOTE
1. If you do not already have it, get the TCP/IP address of the digital sender from the EIO
Jetdirect page. The HP Jetdirect page is the second page that you see when viewing the
configuration page on the control panel.
Before connecting to the digital sender, make sure that it is not in Sleep mode. Also make
sure that any error messages are cleared from the control-panel display.
NOTE
2. Open a command window on your computer.
3.
Type: ftp <TCP/IP ADDRESS>. For example, if the TCP/IP address is 192.168.0.90,
type ftp 192.168.0.90.
4. Press Enter on the keyboard.
5. When prompted for the user name, press Enter.
6. When prompted for the password, press Enter.
7.
Type binat the command prompt.
8. Press Enter. The message 200 Types set to I, Using binary mode to transfer files
appears in the command window.
9.
Type put <FILENAME>, where <FILENAME> is the path to the .RFU file that was
downloaded from the Web. For example, type put C:\LJ\3500FW.RFU, and then
press Enter.
If the file name or path includes a space, you must enclose the file name or path in quotation
NOTE
marks. For example, type put "C:\MY DOCUMENTS\LJ\3500FW.RFU"
The following series of messages appears in the command window:
200 PORT command successful
150 Opening BINARY mode data connection
226 Ready
226 Processing Job
226 Transfer complete
Then, a message containing transfer-speed information appears.
10. The download process begins and the firmware is updated on the device. This can take
about five minutes. Let the process finish without further interaction with the device or
computer.
The digital sender automatically restarts the firmware after processing the upgrade.
NOTE
11.
12.
At the command prompt, type byeto exit the ftp command.
At the command prompt, type exitto return to the Windows interface.
ENWW
Upgrading the firmware
61
Using HP Web Jetadmin to upgrade the firmware
This procedure requires that you have HP Web Jetadmin Version 7.0 or later installed (see
HP Web Jetadmin). Complete the following steps to update a single device through HP Web
Jetadmin after downloading the .RFU file from the HP Web site.
1. Start HP Web Jetadmin.
2. Open the Device Management folder in the drop-down list in the Navigation panel.
Navigate to the Device Lists folder.
3. Expand the Device Lists folder and select All Devices. Locate the digital sender that
you want to update in the list of devices, and then click to select it.
4. Locate the drop-down box for Device Tools in the upper-right corner of the window.
Select Update Printer Firmware from the action list.
5. Click Browse under Upload New Firmware Image and navigate to the location of
the .RFU file that you downloaded from the Web at the start of this procedure. Select the
file.
6. Click Upload to move the .RFU file to the correct location on the HP Web Jetadmin
server. After the upload is complete, the browser window refreshes.
7. Select the new .RFU date code from the Select New Firmware Version drop-down
menu.
8. Click Update Firmware Now. HP Web Jetadmin sends the selected .RFU file to the
device. The digital-sender control panel shows messages that indicate the progress of
the upgrade. At the end of the upgrade process, the digital sender restarts the firmware.
Upgrading the HP Jetdirect Inside firmware
The HP Jetdirect Inside network interface in the device has firmware that can be upgraded
separately from the digital-sender firmware. This procedure requires that you have HP Web
steps to update the HP Jetdirect firmware with HP Web Jetadmin.
1. Open the Web Jetadmin program.
2. Open the Device Management folder in the drop-down list in the Navigation panel.
Navigate to the Device Lists folder.
3. Select the device that you want to update.
4. In the Device Tools drop-down list, select Jetdirect Firmware Update.
5. Under Jetdirect firmware version the Jetdirect model number and current firmware
version are listed. Make a note of these.
7. Scroll down to the list of Jetdirect model numbers and find the model number that you
wrote down.
8. Look at the current firmware version for the model, and see if it is later than the version
that you wrote down. If it is, right-click on the firmware link, following the instructions on
the Web page to download the new firmware file. The file must be saved into <drive>:
\PROGRAM FILES\HP WEB JETADMIN\DOC\PLUGINS\HPWJA\FIRMWARE
\JETDIRECT on the computer that is running the HP Web Jetadmin software.
62
Chapter 3 Administering the digital sender
ENWW
9. In Web Jetadmin, return to the main device list and select the digital sender again.
10. In the Device Tools drop-down list, select Jetdirect Firmware Update again.
11. On the Jetdirect firmware page, the new firmware version appears under Jetdirect
Firmware Available on HP Web Jetadmin. Click the Update Firmware Now button to
update the Jetdirect firmware.
Maintaining the hardware
Maintaining the digital sender can include cleaning, replacing parts, and calibrating the
digital-sender scanner.
Cleaning the digital sender
To maintain the scan quality, clean the device only if the ADF or glass is visibly marked or
dirty, or if you are experiencing a decrease in the scan quality (such as streaking). Clean the
outside of the device with a water-dampened cloth. Clean the inside with only a dry, lint-free
cloth. Observe all warnings and cautions in the following cleaning tasks.
To clean the glass
●
●
Clean the glass only if dirt is visible, or if you see poor scan quality (such as streaking).
Clean the glass surface by wiping it gently with a clean, damp, lint-free cloth. Use an
ammonia-based surface cleaner to dampen the cloth.
Do not pour or spray liquids directly onto the glass. Do not press hard on the glass surface,
as this could break the glass.
CAUTION
CAUTION
To clean the touchscreen
Clean the touchscreen when needed to clear away fingerprints or dust build-up. To clean it,
wipe the touchscreen gently with a clean, water-dampened, lint-free cloth.
Use water only. Solvents or cleaners can damage the touchscreen. Do not pour or spray
water directly onto the touchscreen.
ENWW
Maintaining the hardware
63
To clean the ADF delivery system
1. Lift the top part of the digital sender.
2. Locate the white, vinyl ADF backing.
3. Locate the white, vinyl calibration strips.
4. Clean the ADF backing and the calibration strips by wiping them with a clean, damp, lint-
free cloth. Use an ammonia-based surface cleaner to dampen the cloth.
5. Close the top of the digital sender.
64
Chapter 3 Administering the digital sender
ENWW
To clean the ADF rollers
You should clean the rollers in the ADF if you are experiencing misfeeds or if your originals
show marks as they exit the ADF.
Cleaning the rollers too frequently could introduce dust into the device.
1. Open the ADF.
CAUTION
2. Locate the rollers near the vinyl calibration strips.
3. Wipe the rollers gently with a clean, water-dampened, lint-free cloth.
Do not pour water directly onto the rollers. Doing so might damage the device.
4. Close the ADF.
CAUTION
5. Push the release button to open the ADF cover.
ENWW
Maintaining the hardware
65
6. Locate the rollers.
7. Wipe the rollers with a clean, water-dampened, lint-free cloth.
Do not pour water directly onto the rollers. Doing so might damage the device.
8. Locate the separation pad.
CAUTION
9. Wipe the pad with a clean, water-dampened, lint-free cloth.
10. Close the ADF cover.
Replacing the mylar sheet
If you start to see vertical streaks on the scanned images, as shown in the figure below, you
might need to replace the mylar sheet at the base of the ADF. The device ships with an
envelope containing three extra mylar sheets and installation instructions. The envelope is in
a pocket behind the ADF vinyl backing, as shown in the following figure.
66
Chapter 3 Administering the digital sender
ENWW
C
C
C
C
A
a
A
a
A
a
A
a
A
a
B
B
B
B
c
c
c
c
c
b
b
b
b
B C
b
Follow the instructions that come in the envelope to replace the mylar sheet.
If necessary, you can order extra mylar sheet replacement kits from you HP sales
representative. The HP part number is Q6496A.
NOTE
Diagnostics
Diagnostic tests can be run from the control panel to validate the hardware operation.
LED test
Follow these instructions to test the functionality of the control-panel LEDs.
1. Press the MENU button on the control panel and select the DIAGNOSTICS menu.
2. Select CONTROL PANEL, and then select the LEDs test. The LEDs test turns each
LED on and off in order to verify its functionality.
Display test
Follow these instructions to test the functionality of the control-panel display.
1. Press the MENU button on the control panel and select the DIAGNOSTICS menu.
2. Select CONTROL PANEL, and then select the DISPLAY test. The display test shows
test patterns on the control-panel display.
Buttons test
Follow these instructions to test the functionality of the control-panel buttons.
1. Press the MENU button on the control panel and select the DIAGNOSTICS menu.
2. Select CONTROL PANEL, and then select the BUTTONS test. The buttons test asks
you to press each control-panel button to test its functionality.
ENWW
Maintaining the hardware
67
Touchscreen test
Follow these instructions to test the functionality of the control-panel touchscreen.
1. Press the MENU button on the control panel and touch the DIAGNOSTICS menu.
2. Touch CONTROL PANEL, and then touch TOUCHSCREEN. The touchscreen test
divides the screen into a grid and then asks you to touch each section of the grid to test
its functionality.
Calibrating the scanner
The purpose of the scanner calibration process is to compensate for offsets in the scanner
imaging system (carriage head) for ADF and flatbed scans. Because of mechanical
tolerances, the scanner carriage head might not read the position of the image accurately.
During the calibration procedure, scanner offset values are calculated and stored. The offset
values are subsequently used when producing scans so that the correct portion of the
scanned image is obtained by either adding or subtracting the number of pixels that are
indicated in the offset from the lines or rows of the image.
Scanner calibration should only be carried out if you notice offset problems with the scanned
images. The scanner is calibrated before it leaves the factory and normally should not need
to be calibrated again.
Before calibrating the scanner, you must print the calibration target on a printer.
To print the calibration target
instructions to download the calibration target. The calibration target file is also available
on the documentation CD-ROM that came with the device. The file name is
CALIBRATION.PDF.
2. Print the target on any HP LaserJet printer or another available, laser-quality printer.
a. Place letter or A4 paper in tray 1 (or the multipurpose tray) and adjust the side guides.
b. Print the first pass of the calibration target.
c. Return the first pass of the calibration target to tray 1 so that the arrows are facing
into the printer.
68
Chapter 3 Administering the digital sender
ENWW
d. Print the second pass. The final calibration target must look like the following figure.
If the calibration target does not look like the figure shown here, the calibration process will
fail and the quality of the digital-sender scans will be degraded. The black areas must
extend completely to the edges of the page. If they do not, use a black magic marker
to extend the black areas to the edges of the page.
CAUTION
If you have problems printing the calibration target, try using a different printer.
To calibrate the scanner
1. Take the calibration target to the digital sender.
2. Place it into the scanner ADF face-up and adjust the side guides.
3. Press the MENU button and touch DIAGNOSTICS, and then touch CALIBRATE SCANNER.
4. After the calibration target has passed through the ADF once, reposition it in the ADF in
the opposite direction. After the second pass, the calibration is complete.
The ADF Maintenance Kit
The device notifies you when it is time to replace the ADF Maintenance Kit by showing a
message on the control-panel display. You can view the remaining life of the Maintenance
Kit at any time by pressing the STATUS button on the control panel or visiting the EWS
to install a new ADF Maintenance Kit.
The ADF Maintenance Kit includes the following items:
●
●
●
●
One pick-up roller assembly
One separation pad
One mylar sheet kit
An instruction booklet
Follow the instructions that come with the kit to install it.
After replacing the kit, set the NEW DOCUMENT FEEDER KIT setting in the control-panel
RESETS menu to YES.
ENWW
Maintaining the hardware
69
70
Chapter 3 Administering the digital sender
ENWW
Troubleshooting
4
Use the information in the following sections to troubleshoot specific problems with the digital
sender.
Sources for information about problems
Source
Description
●
Start LED—The Start LED is green when
the device is ready to scan, and amber if an
error exists.
Control-panel lights
●
Ready LED—The green Ready LED is on
when the device is online and ready to scan.
It flashes when a job is paused. It is off if the
device is paused or unable to send data.
●
●
Data LED—The green Data LED is on when
the device is processing a job but has been
paused. It is off when no job is available to
be processed. It flashes when the device is
transmitting data.
Attention LED—If the red Attention LED is
on, the device has encountered a critical
error. If it flashes, the device has
encountered an error that requires user
attention. If it is off, the device is operating
normally.
these LEDs.
Control-panel messages
Messages appear on the control-panel display
when problems exist. See Control-panel error
messages for a list of messages and
recommended actions.
ENWW
Sources for information about problems
71
Source
Description
Activity log
The activity log is a record of digital sender use,
and is probably your best tool for
troubleshooting. It contains messages
(information, warning, or error) that can help you
information about how to view the activity log
information about activity log messages.
HP Web Jetadmin software
This tool can be used to monitor and
troubleshoot the digital sender. See HP Web
Jetadmin for more information. You can also see
the diagnostics and troubleshooting topics in the
HP Web Jetadmin software online help for details.
Embedded Web server (EWS)
Use the EWS to view digital-sender status
information, determine the remaining life on the
ADF Maintenance Kit, view and print internal
pages, receive notification of digital-sender
events, and view and change the network
configuration. See The embedded Web server
for more information.
HP MFP DSS Configuration Utility or Windows
event log error messages
If an error occurs with the HP DSS software you
might see an error message appear in the HP
MFP DSS Configuration Utility or in the Windows
event log. See HP MFP DSS Configuration
error messages for information on these error
messages.
Jams
To avoid jams in the ADF, use the following instructions.
Avoiding jams
Use the following information to avoid jams when using the ADF.
●
●
●
●
When loading paper into the ADF, ensure that the paper stack is square and straight
and the paper guides are adjusted to the width of the page to be scanned
Do not overload the ADF. The ADF was designed to hold 50 sheets of 75 g/m2 (20 lb)
bond paper.
If the paper to be scanned using the ADF was previously folded, flatten it to the best of
your ability. Try to remove all wrinkles and folds from the paper.
If the paper to be scanned using the ADF was previously stapled, it might be necessary
to “fan” the corner of the page where the staple was inserted. Often, the hole that the
staple created makes the pages stick together (that is, interlocks the pages).
72
Chapter 4 Troubleshooting
ENWW
●
Remove any stick-on notes or labels that are affixed to the pages being scanned. If the
labels have deposited excessive residual adhesive to the paper, you might have to clean
it off the paper before it is sent through the ADF.
●
●
●
Paper that has been three-hole punched, been removed from a wire-comb or plastic
comb binding, or has perforations might be difficult to send through the ADF.
If the leading edge of the page to be scanned is excessively worn or frayed, try rotating
the paper before scanning.
Paper can acclimatize to the environment around it. If the operating environment is
excessively dry, the paper might become dry and subject to static electricity. Excessively
dry sheets of paper tend to stick together, which might lead to difficulty when feeding
through the ADF.
Clearing jams
Follow these instructions to clear paper jams in the digital-sender ADF.
1. Press the release button to open the ADF cover.
2. Remove any jammed media from this area.
3. Make sure that you have removed all of the pieces of torn media.
4. Close the ADF cover.
ENWW
Jams
73
Operational issues
Problem
Action to take
The digital sender is not working.
●
Make sure that the power cord is securely
connected to the device and that it is
plugged into the power outlet.
●
●
●
●
Make sure that the digital sender is turned
on.
Verify that the network cable is securely
connected to the device.
Clear any error messages on the control-
panel display.
If the digital sender has successfully
powered up and completed all of its internal
diagnostics, the formatter LED will flash on
and off approximately once every second.
Verify that the formatter LED and Jetdirect
LED appear to be functioning normally. See
The digital sender does not accept your
password.
●
●
Verify that you are using the correct
password.
Passwords are case-sensitive. Make sure
that you type your password with the correct
combination of uppercase and lowercase
letters.
●
Verify that the settings on the
Authentication tab of the HP MFP DSS
Configuration Utility are correct for your
network.
Scanned pages are blank or have repeated
patterns when using the ADF.
Make sure that a page is not already on the glass.
74
Chapter 4 Troubleshooting
ENWW
Problem
Action to take
Vertical streaks appear on the scanned image.
Clean the ADF and glass. See Cleaning the
digital sender. If that does not solve the problem,
replace the mylar sheet. See Replacing the
Placement of the scanned image appears to be
wrong, .
●
●
Make sure that the document you are trying
to send is placed correctly in the ADF or on
the glass.
The scanner might need to be recalibrated.
The image quality is poor.
●
Make sure that the document you are trying
to send is placed correctly in the ADF or on
the glass.
●
●
Make sure that the glass is clean. If the
glass is dirty, clean it with a dry, soft cloth.
If you are scanning from the ADF, try
scanning from the glass. If the image that
was scanned from the glass is better, clean
complete cleaning procedures.
●
If possible, try changing some of the scan
settings, such as resolution or file type, to
improve the image quality.
ENWW
Operational issues
75
Problem
Action to take
The ADF feeds multiple sheets, skews papers,
or jams frequently.
●
●
●
Adjust the guides so that they are snug
against the stack but do not bend the stack.
The maximum number of pages the ADF
can hold is 50 or fewer, depending on the
type of media that is being loaded.
The maximum number of pages the output
tray can hold is 50 or fewer. Make sure that
more pages are not stacking up in the
output tray.
●
The type of media that is being loaded might
not meet the required specifications. See
Paper handling for media specifications.
●
●
Clean the separation pad and the rollers.
If the mylar sheet has recently been
replaced, verify that it was correctly
installed. See the documentation that came
with the mylar sheets.
●
●
If the roller assembly or separation pad has
recently been replaced, verify that it is
correctly installed. See the documentation
that came with the replacement part.
If users have been feeding unsupported
items through the ADF (for example, carbon-
copy forms), the rollers might have
accumulated a residue or been damaged.
You might need to clean the rollers (see
Cleaning the digital sender) or replace the
The "Find Servers" process in the HP MFP DSS
Configuration Utility was not able to find an
SMTP server.
●
●
Verify that there is an active SMTP server
on the network.
Click Add… on the E-Mail tab, and then
type in the host name or IP address of the
SMTP server. After typing in the address,
click the Test button to verify that the
software can contact the server.
●
If testing the server is unsuccessful, see
The "Find Servers" process in the HP MFP DSS
Configuration Utility was not able to find an
LDAP server.
●
●
Verify that you have a functioning LDAP
server on the network.
Type the host name or IP address of the
LDAP server into the LDAP Server text box
on the Authentication tab. After typing in
the address, click the Test button to verify
that the software can contact the server.
●
If testing the server is unsuccessful, see
76
Chapter 4 Troubleshooting
ENWW
Problem
Action to take
An e-mail transmission did not arrive at the
destination e-mail address.
●
If you typed the e-mail address at the
control panel, resend the e-mail message,
making sure that you type the address
correctly and that it is in the correct format
(has no spaces, contains the required @
sign, and contains the required period).
●
Resend the e-mail. Make sure that you type
the name in the correct format in the From:
field so that the message is not rejected and
so that you receive a message back if the
e-mail transmission fails.
●
●
Check the activity log to see if it reflects a
A fax transmission did not arrive at the
destination fax machine.
If you typed the fax number at the control
panel, resend the document, making sure
that you type the fax number correctly.
●
●
●
The receiving fax machine might be turned
off or experiencing an error condition (such
as out of paper or toner). Contact the
recipient.
The system might be busy sending other
digital send jobs. The system might also
have reached its maximum limit of pending
jobs. Wait and then try again.
For information about the transmission,
check any fax notifications that might have
been returned (for example, e-mail
notifications in your e-mail inbox, if these
reports are available with your fax service).
●
●
Resend the fax.
If the problem persists, check the log for the
fax transport that is being used. Logs often
contain information about why a fax
transmission was unsuccessful.
A document sent to a folder did not arrive at the
destination folder.
●
●
Resend the document.
See if the file name was modified to resolve
a duplicate-file-name error.
●
Check the activity log for error messages.
If the document was sent from the glass, the
document page might be too long. The
maximum length for documents scanned from
the glass is A4, or 210 x 297 mm (8.27 x 11.69
inches).
The bottom of a page that you sent is cut off.
ENWW
Operational issues
77
Problem
Action to take
The control panel is using the wrong language.
Use the control-panel menu to set the correct
language.
1. Push the MENU button.
2. Select CONFIGURE DEVICE on the control-
panel display (the third menu item).
3. Touch SYSTEM SETUP (the fourth menu
item).
4. Scroll down and touch LANGUAGE (the last
menu item).
5. Touch the correct language.
78
Chapter 4 Troubleshooting
ENWW
Control-panel error messages
These error messages can appear on the digital-sender control-panel display. Use the
instructions to clear the error message, if necessary.
Error message
Explanation or action needed
Address book is full. To add an address, you
must first delete an address.
You cannot add another address to the address
book because it is full. The address book is
limited to 200,000 entries. You can delete
addresses by touching the Edit button on the
control-panel Address Book screen and then
selecting the Delete option.
Access denied
You are trying to use a feature or access a folder
that you do not have authorization to use. If you
are trying to access a folder, verify that the folder
is set up to be shared.
Close the ADF cover.
ADF COVER OPEN
ADF Empty
You must have a document in the ADF or on the
glass before you can begin a digital-send
operation.
ADF Overfill
Too many sheets have been put into the ADF.
Remove some of the sheets. Up to 50 sheets of
paper can be put into the ADF, with a maximum
height of 5 mm (0.2 inch).
ADF Paper Jam
ADF Pick Error
A jam has occurred in the ADF. See the Jams
section at the beginning of this chapter.
Make sure that your original contains no more
beginning of this chapter.
Check on the status of the rollers and clean
ADF Skew Error
Make sure that the paper guides are aligned on
the sides of the originals, and that all of the
originals are the same size. Follow the
instructions in the onscreen dialog box. See the
Jams section at the beginning of this chapter.
Authentication information is incorrect.
Please re-enter information.
The user name or password that you used is
incorrect. Type the information again.
Verify that the settings on the Authentication
tab of the HP MFP DSS Configuration Utility are
correct for your network.
Authentication Required
A username and password are required in order
to gain access to the feature you selected.
ENWW
Control-panel error messages
79
Error message
Explanation or action needed
Canceling send job
The device is canceling a send job. The
message continues while the job is stopped and
any remaining data is discarded.
CHECK CABLES. CHECK SCANNER LOCK.
A problem exists with the scanner. Make sure
that the scanner lock is in the unlocked position.
the scanner lock.) Turn the device off and then
on again.
Check the glass and remove any paper, then
press "Start"
A document needs to be removed from the
scanner glass.
Clearing event log
The device is clearing the event log.
Digital Send server is not responding
alternates with
The digital sender cannot communicate with the
HP DSS server. Check the network connection.
Verify that the HP DSS server is running.
Contact administrator
E-mail Gateway did not accept the job
because the attachment was too large
The scanned documents have exceeded the
size limit of the e-mail server. The system
administrator sets the size limit. Resend the job
with a lower resolution setting, smaller file size
setting, or fewer pages.
E-mail Gateway did not respond
An e-mail gateway has exceeded the timeout
value. Try resending. If the problem persists,
verify that the SMTP server is functional. See
E-mail Gateway rejected the job because of
the addressing information.
One or more of the e-mail addresses is incorrect.
Double check the e-mail addresses and send the
job again.
alternates with
Job failed
Error executing digital send job. Job failed
An error occurred during an e-mail send job.
Verify that you have typed the correct e-mail
recipient addresses and try sending again. If this
error persists, verify that the SMTP server is
functioning correctly. See Troubleshooting
Event Log Empty
The user is attempting to view an empty event
log by selecting Show Event Log from the
control panel.
Flash File System is Full
The flash disk or file system has reached
maximum capacity. Wait for all pending jobs to
be sent and then try again.
80
Chapter 4 Troubleshooting
ENWW
Error message
Explanation or action needed
Flash is Write Protected
The flash file is protected, and no new files can
be written to it.
To enable writing to the flash memory, use HP
Web Jetadmin to turn off write protection.
To remove this message from the display, turn
the device off and then on.
Folder list is full. To add a folder you must
first delete a folder
The digital sender limits the number of folders
that can be established to 512. Delete an
unused folder by using the Remove button on
the Folders tab in the HP MFP DSS
Configuration Utility.
Found LDAP Gateway:...
Found SMTP Gateway:...
Gateways failed
This message appears in response to the FIND
SEND GATEWAYS menu command.
This message appears in response to the FIND
SEND GATEWAYS menu command.
This message appears if you execute the TEST
SEND GATEWAYS menu item and the test fails.
Check the network connection and contact the
network administrator. See Troubleshooting
Gateways OK
This message appears if you execute the TEST
SEND GATEWAYS menu item and the test is
successful.
HP Digital Sending: Delivery Error
Try sending the job again. If you continue to
experience problems, check the network
connection and contact the network administrator.
Initializing permanent storage
Internal disk not functional
This message appears momentarily during
power-up when the device hard disk is initializing.
The internal hard disk has failed. Turn the device
off and then on. If this message persists, contact
an HP-authorized service or support provider.
(See the HP support flyer or go to
LDAP failed
This message appears if you execute the TEST
LDAP GATEWAYS menu item and the test fails.
Verify that the network connection is functioning
and that the LDAP gateway information is
correct. See Troubleshooting SMTP and LDAP
LDAP Gateway OK
This message appears if you execute the TEST
LDAP GATEWAYS menu item and the test is
successful.
ENWW
Control-panel error messages
81
Error message
Explanation or action needed
LDAP Server is not responding. Contact
Administrator.
The device is unable to communicate with the
LDAP server. Verify that the LDAP server is
functioning. See Troubleshooting SMTP and
Name is already added to list
You have tried to add a duplicate name in one of
the digital-sender address books.
Network connection required for Digital
Sending. Contact administrator.
The device is unable to establish a connection
with the network. Contact the network
administrator.
Novell Login Required
The device has been configured to require a
Novell login in order to use the selected feature.
Password or name is incorrect. Please enter
correct login.
The user name or password is incorrect or was
mistyped. Retype the user name and password.
Verify that the settings on the Authentication
tab of the HP MFP DSS Configuration Utility are
correct for your network.
Phone book is full. To add a phone number
you must first delete a phone number.
You cannot add another phone number to the
phone book because it is full.
Please refine your search
Your search has returned more results than the
device can show. Try to narrow your search.
Replace Document Feeder Kit
The scan count indicates that it is time to replace
the ADF Maintenance Kit. See The ADF
Scan carriage locked
Make sure that the scanner lock is in the
unlocked position. (See Parts of the digital
sender for the location of the scanner lock.)
Sleep mode on
SMTP Failed
The device is in sleep mode. Press any control-
panel key to bring it out of sleep mode.
This message appears if you execute the TEST
SMTP GATEWAY menu item and the test fails.
Verify that the network connection is functioning
and that the SMTP gateway information is
correct. See Troubleshooting SMTP and LDAP
SMTP Gateway Not Responding
SMTP Gateway OK
The SMTP gateway has exceeded a timeout
value. Try sending again. Verify that the SMTP
server is functional. See Troubleshooting SMTP
This message appears if you execute the TEST
SMTP GATEWAY menu item and the test is
successful.
The Digital Sender is currently processing
the maximum number of active jobs allowed.
Please try to send your job later.
The digital sender is busy sending other jobs.
Wait and try your job in a few minutes.
82
Chapter 4 Troubleshooting
ENWW
Error message
Explanation or action needed
The folder you have entered is not a valid
folder.
The device was unable to validate the path you
typed in for the send-to-folder feature. Verify that
you have typed the correct path.
Too many addresses were found to display.
Please refine your search.
Your search has returned more results than the
device can show. Try to narrow your search.
Username or password is incorrect. Please
re-enter.
The user name or password is incorrect or was
mistyped. Retype the user name and password.
Verify that the settings on the Authentication
tab of the HP MFP DSS Configuration Utility are
correct for your network.
Windows Login Required to use this feature
11.xx Internal Clock Error
Provide your Windows network credentials to
use the digital-sending feature.
The internal clock is not working. The digital
sender can still send, but you are prompted to
set the date and time whenever the device is
turned off and then turned on. Time stamping for
documents and events might be affected.
To resolve this issue, contact an HP-authorized
service or support provider. (See the HP support
20 Insufficient Memory
22 EIO Buffer Overflow
The the scanned document contains more data
than can fit in the device's available memory.
Press START to send the available data (some
data might be lost), and then try to make the
scan job smaller.
Too much data was sent to the EIO card in the
specified slot. An incorrect communications
protocol might be in use. Turn the device off and
then on. If this message persists, contact an HP-
authorized service or support provider. (See the
HP support flyer or go to http://www.hp.com/
22 Embedded I/O Buffer Overflow
Too much data was sent to the embedded
HP Jetdirect network interface. Turn the device
off and then on. If this message persists, contact
an HP-authorized service or support provider.
(See the HP support flyer or go to
ENWW
Control-panel error messages
83
Error message
Explanation or action needed
30.1.yy Scanner Failure
An error exists with the flatbed scanner. Turn the
device off and then on. If this message persists,
contact an HP-authorized service or support
provider. (See the HP support flyer or go to
A 30.18 Scan Failure message might indicate
that the scanner head is locked. Verify that the
scanner lock is in the unlocked position. (See
Parts of the digital sender for the location of the
scanner lock.)
40 EIO Bad Transmission
40 Embedded I/O Bad Transmission
52.xy Error
The connection between the device and the EIO
card has failed. Press START to clear the error
and continue sending.
The connection with the embedded HP Jetdirect
network interface has failed. Turn the device off
and then on.
The scanner has encountered an error. Turn the
device off and then on. If this message persists,
contact an HP-authorized service or support
provider. (See the HP support flyer or go to
57.xx Error
The fan motor has encountered an error. Turn
the device off and then on. If this message
persists, contact an HP-authorized service or
support provider. (See the HP support flyer or go
64 ERROR
A scan buffer error occurred. Turn the device off
and then on. If this message persists, contact an
HP-authorized service or support provider. (See
the HP support flyer or go to http://www.hp.com/
alternates with
To continue turn off then on
68.x Storage Error Settings Changed
An error occurred in the device nonvolatile
memory (NVRAM), and one or more device
settings have been reset to their factory default.
Sending can continue, but some unexpected
functions might result because the error
occurred in permanent storage.
Pressing START should clear the message. If this
message persists, contact an HP-authorized
service or support provider. (See the HP support
84
Chapter 4 Troubleshooting
ENWW
Error message
Explanation or action needed
68.x Permanent Storage Full
The device NVRAM is full. Some settings saved
in the NVRAM might have been reset to the
factory defaults.
Sending can continue, but some unexpected
functions might result because the error
occurred in permanent storage.
Pressing START should clear the message. If this
message persists, contact an HP-authorized
service or support provider. (See the HP support
68.x Permanent Storage Write Fail
The device NVRAM is failing to write.
Sending can continue, but there might be some
unexpected functions because the error
occurred in permanent storage.
Pressing START should clear the message. If this
message persists, contact an HP-authorized
service or support provider. (See the HP support
ENWW
Control-panel error messages
85
HP MFP DSS Configuration Utility error messages
The following table lists and explains messages that might appear on the screen while you
are using the HP MFP DSS Configuration Utility. If the problem persists, contact an
authorized HP dealer.
Message
Description and actions
<computer network name> is not responding
or is not a valid SMTP gateway server.
The named computer is either not currently
running, not available through the network, or
not running as an SMTP gateway.
●
Make sure the computer is turned on,
available through the network, and running
as an SMTP gateway.
Access violation. Read access is denied.
The HP MFP DSS Configuration Utility could not
read from the specified folder on the specified
file server.
●
●
Make sure the folder exists.
Make sure you have read permission for the
folder.
Access violation. Unable to log off from the
file server.
The HP MFP DSS Configuration Utility could not
logoff from the specified file server.
●
Try testing the file server again to make
sure that it is still running and available
through the network.
Access violation. Unable to log on to the file
server.
The HP MFP DSS Configuration Utility could not
logon to the specified file server.
●
●
●
Make sure you entered valid logon
credentials to gain access to the file server.
Make sure the file server is running (if not
the local computer).
Make sure the file server is available
through the network (if not the local
computer).
Access violation. Write access is denied.
The HP MFP DSS Configuration Utility could not
write to the specified folder on the specified file
server.
●
●
Make sure the folder exists.
Make sure you have write permission for the
folder.
86
Chapter 4 Troubleshooting
ENWW
Message
Description and actions
The account for user <user name> is
currently inaccessible.
The named user does not currently have logon
privileges—either because the account is locked
or the user password has expired.
●
●
Unlock the user account.
Update the user password.
The domain <domain name> is unknown.
The named domain is not recognized as valid.
●
●
Make sure the named domain is correct.
Make sure your computer can gain access
to the named domain.
The HP Configuration Utility is already being
run on <computer network name>.
The HP MFP DSS Configuration Utility is already
running remotely on the named computer. More
than one instance of the HP MFP DSS
Configuration Utility cannot run at the same time.
This eliminates the possibility of configuration
conflicts.
●
Wait until the HP MFP DSS Configuration
Utility that is running remotely is closed.
The LDAP server is currently too busy to
handle your request.
The LDAP server ended the connection with the
HP MFP DSS Configuration Utility because
resources were insufficient.
●
Test the LDAP settings again later.
The LDAP server or the connection has failed. The HP MFP DSS Configuration Utility lost its
connection with the LDAP server.
●
Make sure the LDAP server is working
properly.
●
Test the LDAP settings again later.
The license <license number> is for a
previous version of this product and is not
supported in the current version.
You entered a license number that enables the
send to e-mail feature. However, that feature is
now free in your version of the product.
The specified LDAP server is invalid or is not An LDAP connection could not be established
running LDAP. with the specified server.
●
Make sure the specified server is
functioning and that it is running the LDAP
server.
●
●
Make sure the correct TCP/IP port is
specified in Advanced Settings.
Make sure the specified server is available
through the network.
ENWW
HP MFP DSS Configuration Utility error messages
87
Message
Description and actions
Unable to start DSS service. You may need to HP DSS must be running before you can start
reinstall the software.
the HP MFP DSS Configuration Utility. However,
an attempt to start HP DSS was unsuccessful.
●
●
●
Manually start the HP DSS service by
means of the Windows Control Panel.
Restart the computer on which HP DSS is
installed.
Uninstall and reinstall HP DSS.
Unexpected failure.
An unspecified error occurred while the
connection with the LDAP server was being
tested.
●
●
●
Make sure the LDAP settings are correct.
Restart HP DSS.
Restart the computer on which HP DSS is
installed.
User has no e-mail address in the LDAP
database.
The user record that was located did not contain
an e-mail address.
●
Make sure that the Obtain e-mail address
from setting is correct.
●
Make sure that the user’s LDAP record
contains an e-mail address.
User not found in the LDAP database.
No user record matched the search criteria that
was entered.
●
●
●
●
Make sure the user has a record in the
LDAP database.
Make sure the Find addresses in address
book using setting is correct.
Make sure the Search Root information is
correct.
Make sure the logon credentials are correct.
88
Chapter 4 Troubleshooting
ENWW
Digital-sender event log messages
The following messages are those that you might see in the digital-sender event log.
To view the digital-sender event log, open the HP MFP DSS Configuration program and click
the MFP Configuration tab. Select the digital sender in the MFP list, and then click
Configure MFP. Click the Log tab to see the activity log for the selected device.
Event
Description
Action to take
Address Book Check
The address book database
was checked for corruption.
None
Address Book Clear Event
An address book has been
cleared using the Address
Book Manager (ABM).
None
Address Book Export
Address Book Import
Authentication Failure
An address book was exported
using the ABM.
None
None
An address book was imported
using the ABM.
A user was unable to
authenticate at the device.
●
●
The user should attempt to
log in again.
If the login still fails, verify
the settings on the
Authentication tab of the
HP MFP DSS
Configuration Utility. Use
the Test button to test the
settings.
●
●
Turn the digital-sending
device off and then back on.
Restart the HP DSS
service.
Communication Protocol Error
Protocol Version Error
An error occurred while
communicating with the digital
sender.
●
●
Turn the device off and
then back on.
Verify that you have the
latest version of the
HP DSS service installed.
If the problem persists, contact
an HP authorized service
representative.
ENWW
Digital-sender event log messages
89
Event
Description
Action to take
Database Access Error
A database corruption error
has occurred.
●
●
●
Check the Windows
system log for disk errors.
Restart the HP DSS
service.
Delete the database
directory (the \DB directory
within the HP DSS
program directory) and
restart the HP DSS service.
E-mail Protocol Error
Cannot connect to the SMTP
server
An e-mail message could not
be sent due to network or
server problems.
E-mail Communication Error
E-mail Server Unavailable Error
●
Verify that the e-mail
server is running.
●
Test the e-mail settings on
the E-mail tab of the
HP MFP DSS
Configuration Utility.
●
Verify that the correct
"From" address is being
used in the e-mail.
●
●
Restart the HP DSS
service.
Check the SMTP server
logs for errors.
If the problem persists, contact
an HP authorized service
provider.
Job Tracking Failure
A digital-send job could not be
processed due to a Job
Recovery Failure.
An error occurred while retrying
a previously uncompleted job.
●
Check to see if there have
been any disk errors.
●
Verify that the disk
containing the HP DSS
service is not full.
●
Restart the HP DSS
service.
If the problem persists, contact
an HP authorized dealer.
90
Chapter 4 Troubleshooting
ENWW
Event
Description
Action to take
Startup Failure
A digital-sending subsystem
did not start successfully.
●
●
Restart the HP DSS
service.
Verify that the HP DSS
server has enough
memory and disk space.
●
●
Check the Windows event
log for disk errors.
Check the security settings
of the temporary files
folder. (The temporary files
folder is shown on the
HP MFP DSS
Configuration Utility
Preferences tab.)
●
●
Reinstall the HP DSS
program.
Verify that you have the
latest version of the
HP DSS service installed.
support/dss If the latest
version is not installed,
upgrade to the latest
version.
If the problem persists, contact
an HP authorized service
provider.
Windows event log error messages
The following table lists and explains the Windows event log messages generated by HP
DSS running on the Windows server computer. If the problem persists, contact an
authorized HP dealer.
The event log, available through Microsoft’s Event Viewer, lets you monitor events in the
Windows operating system that are related to digital sending. The event log service starts
automatically when you start the HP DSS server computer. Follow these instructions to
reach the event log.
1. From the HP DSS server, click Start and then point to Settings.
2. Click Control Panel, click Administrative Tools.
3. Click Event Viewer, then view the system log.
ENWW
Windows event log error messages
91
Message
Description and actions
DSS v. x.x - Started with Warnings
HP DSS was unable to start because of missing
files or memory limitations.
DSS v. x.x - Aborted
●
●
Restart HP DSS.
DSS v. x.x - Internal Initialization Failed
DSS v. x.x - TCP/IP Initialization Failed
DSS v. x.x - IMSP Server Initialization Failed
DSS v. x.x - Email Server Initialization Failed
DSS v. x.x - Log Server Initialization Failed
DSS v. x.x - Downloader Initialization Failed
DSS v. x.x - Job Manager Initialization Failed
DSS v. x.x - JetSend Initialization Failed
DSS v. x.x - Timer Initialization Failed
Restart the computer on which HP DSS is
installed.
●
●
Uninstall and reinstall HP DSS.
Add more memory to the computer.
DSS v. x.x - Error Server Initialization Failed
DSS v. x.x - Pipe Server Initialization Failed
HP DSS was unable to start because of missing
files or memory limitations.
●
●
Restart HP DSS.
DSS v. x.x - Unknown Error X, Internal (X,
X,X) Mode X, Job ID X, Gravity X
Restart the computer on which HP DSS is
installed.
●
●
Uninstall and reinstall HP DSS.
Add more memory to the computer.
DSS v. x.x - Internal Error IMSP Server,0
Failure initializing address books.
●
●
Restart HP DSS.
Reset the address books.
DSS v. x.x - Internal Error IMSP Server,50
through IMSP Server,56
Failure initializing address books.
Restart HP DSS.
●
DSS v. x.x - Internal Error IMSP Server,57
Internal error in managing address books.
Restart HP DSS.
●
DSS v. x.x - Internal Error IMSP Server,58
through IMSP Server,59
Unrecoverable problem with address books.
Contact an authorized HP dealer.
●
DSS v. x.x - Internal Error IMSP Server,60
Address book contents lost.
●
●
Restart HP DSS.
Re-import the addresses into the address
books.
DSS v. x.x - Internal Error IMSP Server,100
through IMSP Server,206
Failure loading address books.
Restart HP DSS.
●
92
Chapter 4 Troubleshooting
ENWW
Message
Description and actions
DSS v. x.x - Internal Error IMSP Server,300
through IMSP Server,304
The network link to the address book is missing.
This indicates a possible problem with the
network connection.
●
●
Make sure all cabling is securely connected.
Restart HP DSS.
DSS v. x.x - Internal Error IMSP Server,400
through IMSP Server,403
A problem exists in the address book hard drive
(computer), or another internal problem exists.
●
Restart HP DSS.
DSS v. x.x - Address Book Error
An internal problem gaining access to address
books has occurred.
●
Restart HP DSS.
Troubleshooting SMTP and LDAP servers
During the configuration of the HP DSS program, you must locate the SMTP server and
LDAP server on your network and test them to make sure they are functional. On most
standard networks, using the Find Servers and Test buttons in the HP MFP DSS
the SMTP or LDAP server. If this is the case, use the instructions in the following sections to
find and test the server.
Finding the LDAP server address
The LDAP "Find Servers" function searches the network by querying DNS servers and
MFPs that have been configured for LDAP. Servers that can provide LDAP functionality
include e-mail servers and directory servers such as the following:
●
●
●
Microsoft Exchange 5.5 and Exchange 2000 servers
Microsoft Active Directory servers
Novell Directory Services servers.
If you have one of these types of servers on your network and know the address, try typing it
into the LDAP Server text box on the Authentication tab. Then click the Find Settings
button to retrieve the settings.
ENWW
Troubleshooting SMTP and LDAP servers
93
Verifying an LDAP address
Use this procedure to verify that the LDAP server address you are using is valid.
1. Open a Web browser.
2.
Type LDAP://[hostname or IP address of LDAP server]into the browser
address box, using the host name or IP address of the LDAP server you are using for
digital sending.
3. Press Enter. If the Find People dialog box appears, the LDAP server address is valid. If
the dialog box does not appear, contact your network administrator to verify that the
server is functioning.
Troubleshooting the LDAP Find Settings process
When you click the Find Settings button on the Authentication tab, the program uses the
entries in the Accessing the LDAP Server and Searching the Database sections of the
tab to find the correct settings for your LDAP server. Setting or changing these entries can
affect the success of the Find Settings process. Try the following settings:
1. Select Anonymous from the LDAP Server Bind Method drop-down list, and then
delete any data from the Search Root text box so that it is blank.
2. Click Find Settings.
3. Click Test and type a user name and password to test the software's ability to retrieve
an e-mail address. If the test succeeds, your LDAP configuration is complete. If the test
fails, continue on to Step 4.
4. Select Simple or Windows Negotiated (SPNEGO) from the LDAP Server Bind
Method drop-down list. Select Use MFP user's credentials.
If you are troubleshooting LDAP settings on the Addressing tab, or in the Configure MFP
Addressing settings, the options displayed are slightly different. If you use the Simple or
Windows Negotiated bind method, you must specify a username and password.
NOTE
5. Click Find Settings.
6. Click Test and type a user name and password to test the software's ability to retrieve
an e-mail address. If the test succeeds, your LDAP configuration is complete. If the test
fails, consult with your network administrator.
The attributes in the Find MFP user in database section of the Authentication tab match
what the user types in at the device control panel to a unique user record in the LDAP
database. You can select Exchange 5.5 Defaults or Active Directory Defaults from the
MFP user information retrieval drop-down list to use the default settings for these server
types. You must have some knowledge of the LDAP database structure in order to use the
Custom option. If the Custom option is selected, you can either type in or select an entry in
the Using the LDAP attribute of... field. This must correspond to what is selected in the
match the MFP user login ID... field below it.
NOTE
94
Chapter 4 Troubleshooting
ENWW
Finding an SMTP server address
The SMTP "Find Servers" function queries the DNS server for the "Mail Exchanger (MX)"
record. If the Find Servers process fails, try the following:
1.
Verify that the HP DSS server has obtained valid DNS settings by typing ipconfig /
allat a command prompt.
2. If the ipconfig command returns valid DNS settings, ping the DNS server address to
verify communication with the server. For example, type ping 10.0.0.2at a
command prompt, where 10.0.0.2 is the IP address of the DNS server.
If these two tests succeed, you should have a valid SMTP server. Use the Add button on the
E-mail tab to specify the host name or IP address of the SMTP server, then use the Test
button to test the server.
If the Test process fails, verify that you have specified the correct SMTP server address. If
you have specified the correct address, use a ping command to verify communication with
the server. For example, type ping 10.0.0.2at a command prompt, where 10.0.0.2 is the
IP address of the SMTP server. If the ping command fails, contact your network or mail
administrator to verify network and SMTP server functionality.
Verifying an SMTP address
Use this procedure to verify that the SMTP server address you are using is valid.
1.
2.
Click Start and then Run and then type CMDinto the Open text box to open a command
prompt.
Type Telnet [hostname or IP address of SMTP server] 25, using the
hostname or IP address of the SMTP server you are using for digital sending.
3. Press Enter. You should see something similar to the following:
220 samplemail.hp.com ESMTP Server <Microsoft Exchange Internet
Mail Service 5.5> ready. If you see this, the SMTP server address is valid. If you
do not see this message, contact your network or mail administrator to verify that the
server is functioning.
ENWW
Troubleshooting SMTP and LDAP servers
95
LED indications
The LEDs on the digital-sender formatter board and on the HP Jetdirect network port can
help troubleshoot problems.
1
2
Network port LEDs
Formatter LED
Use the green LEDs on the network interface card to confirm that the interface card is
correctly connected to the network and that the network connection is active. Either the 10
Mbps or 100 Mbps LED should be on.
The formatter LED should blink at a steady rate of one blink per second. If it is not blinking,
this indicates a serious error. Turn the device off and then back on again, and look for error
messages on the control-panel display. If the problem persists, contact an HP-authorized
service or support provider. (See the HP support flyer or go to http://www.hp.com/
96
Chapter 4 Troubleshooting
ENWW
Service and support
A
Hewlett-Packard limited warranty statement for hardware
HP PRODUCT
HP 9200C Digital Sender
DURATION OF LIMITED WARRANTY
1 year, Onsite service
HP warrants to you, the end-user customer, that HP hardware and accessories will be free from defects in
materials and workmanship after the date of purchase, for the period specified above. If HP receives notice of
such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be
defective. Replacement products might be either new or equivalent in performance to new.
HP warrants to you that HP software will not fail to execute its programming instructions after the date of
purchase, for the period specified above, due to defects in material and workmanship when properly installed and
used. If HP receives notice of such defects during the warranty period, HP will replace software which does not
execute its programming instructions due to such defects.
HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is unable, within a
reasonable time, to repair or replace any product to a condition as warranted, you will be entitled to a refund of
the purchase price upon prompt return of the product.
HP products might contain remanufactured parts equivalent to new in performance or might have been subject to
incidental use.
Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration, (b)
software, interfacing, parts or supplies not supplied by HP, (c) unauthorized modification or misuse, (d) operation
outside of the published environmental specifications for the product, or (e) improper site preparation or
maintenance.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER
WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED AND HP
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY,
SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE. Some countries/regions, states or
provinces do not allow limitations on the duration of an implied warranty, so the above limitation or exclusion
might not apply to you. This warranty gives you specific legal rights and you might also have other rights that vary
from country/region to country/region, state to state, or province to province. HP's limited warranty is valid in any
country/region or locality where HP has a support presence for this product and where HP has marketed this
product. The level of warranty service you receive might vary according to local standards. HP will not alter form,
fit or function of the product to make it operate in a country/region for which it was never intended to function for
legal or regulatory reasons.
ENWW
Hewlett-Packard limited warranty statement for hardware
97
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE
YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS
SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL
(INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR
OTHERWISE. Some countries/regions, states or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion might not apply to you.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY
PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY
STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
Hewlett-Packard limited warranty statement for software
HP PRODUCT
DURATION OF WARRANTY
HP MFP DIGITAL SENDING SOFTWARE v. 4.0 90 days
1. HP warrants to you that the HP SOFTWARE PRODUCT will not fail to execute its
programming instructions for 90 days after the date of purchase due to defects in
material and workmanship when properly installed and used. If HP receives notice of
such defects during the warranty period, HP will replace SOFTWARE PRODUCT media,
which does not execute its programming instructions due to such defects.
2. HP does not warrant that the operation of HP products will be uninterrupted or error free.
If HP is unable, within a reasonable time, to replace the SOFTWARE PRODUCT to a
condition as warranted, HP may request that you uninstall the SOFTWARE PRODUCT
and return it to HP for a refund.
3. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THE EXPRESS
WARRANTY SET FORTH ABOVE. Some states or provinces do not allow limitations on
the duration of an implied warranty, so the above limitation or exclusion might not apply
to you. This warranty gives you specific legal rights and you might also have other rights
that vary from state to state, or province to province.
4. THE REMEDIES IN THIS WARRANTY STATEMENT ARE YOUR SOLE AND
EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP
BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL (INCLUDING LOST PROFIT), OR OTHER DAMAGE, WHETHER
BASED IN CONTRACT, TORT, OR OTHERWISE. Some states or provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Note: The limited warranty for this product and accompanying software is located in the
product documentation that you received with this product. Please review it at this time.
ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE HP SOFTWARE LICENSE
TERMS SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR
ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE
TERMS, YOU MUST RETURN THE SOFTWARE FOR A FULL REFUND. IF THE
SOFTWARE IS SUPPLIED WITH ANOTHER PRODUCT, YOU MAY RETURN THE
ENTIRE UNUSED PRODUCT FOR A FULL REFUND.
98
Appendix A Service and support
ENWW
Availability of support and service
Around the world, HP provides a variety of service and support options for purchase.
Availability of these programs will vary depending upon your location.
HP maintenance agreements
HP has several types of maintenance agreements that meet a wide range of support needs.
Maintenance agreements are not part of the standard warranty. Support services vary by
location. Contact HP Customer Care to determine the services available to you and for more
information about maintenance agreements. In general, the digital sender will have the
following maintenance agreement:
Next-Day Onsite Service
This agreement provides support by the next working day following a service request.
Extended coverage hours and extended travel beyond HP’s designated service zones are
available on most on-site agreements (for additional charges).
ENWW
HP maintenance agreements
99
100 Appendix A Service and support
ENWW
Specifications
B
Digital Sender specifications
Physical specifications
Height
Depth
Width
Weight
340.26 mm
571.82 mm
452.62 mm
22.7 kg
(50 lbs)
(13.40 inches)
(22.51 inches)
(17.82 inches)
Electrical specifications
Power requirements
100-240V (±10%)
50/60 Hz (±2 Hz)
Minimum recommended circuit capacity
1.0 Amp
Power requirements are based on the country/region where the device is sold. Do not
convert operating voltages. This will damage the digital sender and void the product warranty.
WARNING!
Power consumption (average, in watts)1
Product Model
Scanning (47
PPM)2
Ready
Sleep
13 W
Off
HP 9200C Digital
Sender
95 W
36 W
0 W
support/9200C for current information.
2Power reported is highest value measured for color and monochrome scanning using all
standard voltages.
3Default time from Ready Mode to Sleep = 60 minutes.
5Heat dissipation in Ready Mode = 123 BTU/Hour.
ENWW
Digital Sender specifications 101
Environmental specifications
Recommended1
Operating1
Storage1
Temperature
20° to 27°C
0° to 40°C
-40° to 60°C
(68° to 81°F)
(32° to 104°F)
(-40° to 140°F)
Relative humidity
20 to 70 percent
15 to 80 percent
15 to 90 percent
Acoustic emissions (HP 9200C Digital Sender)1
Declared per ISO 92961
Sound Power Level
Scanning (47 PPM)
LWAd = 6.6 Bels (A) [66 dB (A)]
LWAd = 5.4 Bels (A) [54 dB (A)]
Ready
Declared per ISO 92961
LpAm = 51 dB(A)
Sound Pressure Level - Bystander Position
Scanning (47 PPM)
Ready
LpAm = 39 dB(A)
support/9200C for current information.
2Configuration tested: Scanning simplex monochrome using ADF at 47 ppm and letter paper.
102 Appendix B Specifications
ENWW
FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If this equipment is not
installed and used in accordance with the instructions, it can cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation; the presence of interference can be determined by turning the
equipment off and on. If this equipment does cause harmful interference to radio or
television communications, the user is encouraged to try to correct the interference by one or
more of the following measures:
●
●
●
Reorient or relocate the receiving antenna.
Increase distance between equipment and receiver.
Connect equipment to an outlet on a circuit different from that to which the receiver is
located.
●
Consult your dealer or an experienced radio/television technician.
Any changes or modifications to the device that are not expressly approved by HP could
void the user’s authority to operate this equipment.
NOTE
104 Appendix C Regulatory information
ENWW
Environmental Product Stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally
sound manner. This product has been designed with several attributes to minimize impacts
on our environment.
Power consumption
Power usage drops significantly while in Sleep mode, which saves natural resources and
saves money without affecting the high performance of this product.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance
the ability to identify plastics for recycling purposes at the end of the product's life.
Materials and recycling information
Material restrictions
This HP product contains mercury in the fluorescent lamp of the control-panel liquid crystal
display that can require special handling at end-of-life.
This HP product contains a lithium battery on the formatter board that can require special
handling at end-of-life.
authorities or the Electronics Industry Alliance: http://www.eiae.org.
For more information
To obtain information about environmental topics, including:
●
●
●
●
the product environmental profile sheet for this and many related HP products
HP's commitment to the environment
HP's environmental management system
HP's end-of-life product return and recycling program
ENWW
Environmental Product Stewardship program 105
106 Appendix C Regulatory information
ENWW
Declaration of conformity
Declaration of Conformity
according to ISO/IEC Guide 22 and EN 45014
Manufacturer's Name:
Manufacturer's Address:
Hewlett-Packard Company
11311 Chinden Boulevard
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name:
Regulatory Model Number3):
Product Options:
HP Digital Sender 9200C
BOISB-0401-00
ALL
conforms to the following Product Specifications:
Safety:
EMC:
IEC 60950-1:2001 / EN60950-1: 2001
IEC 60825-1:1993 + A1 + A2 / EN 60825-1:1994 + A2 (Class 1 Laser/LED Product)
GB4943-2001
CISPR 22:1997 / EN 55022:1998 Class B1)
EN 61000-3-2:2000
EN 61000-3-3:1995/ A1
EN 55024:1998
FCC Title 47 CFR, Part 15 Class B2), ICES-003, Issue 4
GB9254-1998, GB17625.1-1998
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC, and carries
the CE-Marking accordingly.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems. Compliance testing of product to
standard with exception of Clause 9.5, which is not yet in effect.
2) This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device can not cause
harmful interference, and (2) this device must accept any interference received, including interference that can cause undesired operation.
3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name
or the product number(s).
Boise, Idaho , USA
June 16, 2004
For regulatory topics only:
Australia Contact:
European Contact:
Product Regulations Manager, Hewlett-Packard Australia Ltd., 31-41 Joseph Street Blackburn, Victoria 3130, Australia
Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe, Herrenberger Strasse 140 , D-71034, Böblingen (FAX: +49-7031-14-3143)
USA Contact:
Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160 Boise, Idaho 83707-0015,
(Phone: 208-396-6000)
ENWW
Declaration of conformity 107
Index
A
cleaning 63
address books
control panel
clearing 52, 56
personal 30
ADF
bins, locating
calibration 68
cleaning 63
lights and buttons
locating
paper specifications
speed
administrator contact information
administrator privileges
testing 67
alerts 39
D
date
settings 39, 45
B
troubleshooting 83
diagnostics 67
Digital Sending Software. See DSS
bins, ADF
buttons, control panel
locating
testing 67
C
calibration 68
ENWW
Index 109
DSS
configuring
flatbed
calibrating 68
speed
FTP
General tab
opening
Preferences 31
G
testing 35
uninstalling 35
gateways
troubleshooting 76, 80
duty cycle
General tab, HP DSS
E
e-mail
H
alerts 39
HP DSS
configuring 10
secondary 13
configuring
security 13
troubleshooting 77, 80
embedded Web server
features 37
General tab
opening
testing 35
uninstalling 35
viewing 38
HP Jetdirect Inside
I
F
faxing
input bin
settings 16
interface ports
troubleshooting 77
features 1, 2
IP address
110 Index
ENWW
media specifications
memory
J
included
jams
troubleshooting 83
menus, control panel
Diagnostics 53
clearing 73
preventing 72
release button, locating
Enhancement 42
I/O 47
Jetdirect Inside
Information 41
locking 55
K
Originals 41
keys, control panel
locating
Resets 52
Sending 43
testing 67
Service 54
viewing 41
L
language
LDAP servers
configuration 15
troubleshooting 76, 93
LEDs, control panel
N
networks
administrator contact information
administrator privileges
locating
testing 67
HP Jetdirect Inside
troubleshooting 71
requirements
licenses, HP DSS
lights, control panel
locating
testing 67
Novell NetWare support
troubleshooting 71
O
on/off switch
operating system requirements
output bin
P
M
packets 47
maintenance kit, ADF
replacing 69
pages per minute
paper jams
clearing 73
preventing 72
media jams
clearing 73
preventing 72
paper specifications
passwords 74
ENWW
Index 111
SMTP servers
ports
power switch
configuring 10
troubleshooting 76, 93
software
privileges, administrator
HP DSS, opening
licenses
Q
uninstalling 35
warranty 98
R
recycling 105
regulatory statements
FCC 104
space requirements
specifications
duty cycle
electrical 101
release button, jams
environment 6, 102
replacing
features
network requirements
paper
physical 101
space requirements
speed
speed specifications
support 99
system requirements
S
scanner
security
T
time
e-mail 13
settings 39, 45
troubleshooting 83
touch screen
cleaning 63
serial number, locating
servers
testing 68
troubleshooting
about 71
settings 47
troubleshooting 76, 93
e-mail 77, 80
faxing 77
112 Index
ENWW
114 Index
ENWW
© 2004 Hewlett-Packard Development Company, L.P.
www.hp.com
*Q5916-90930*
*Q5916-90930*
Q5916-90930
|