HITACHI CP AX2505 User Manual

Projector

CP-AX2505/CP-AX3005/CP-AX3505

CP-AW2505/CP-AW3005

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this

product. Be sure to read “Safety Guide” ﬁrst. After reading them, store them in a

safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are

described below.

WARNING This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect

handling.

NOTICE

This entry notices of fear of causing trouble.

Please refer to the pages written following this symbol.



NOTE • The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Introduction

Features

The projector provides you with the broad use by the following features.

ü The unique optics system produces a large projected image in a short

distance, which provides you with various ways of use.

ü This projector has a variety of I/O ports that supposedly cover for any

business scene.

ü The HDMI port can support various image equipment which have digital

interface to get clearer pictures on a screen.

ü Has an HDCR and an ACCENTUALIZER features which are Hitachi's original

image stabilizer for a clearer image.

ü Has a DICOM^®("Digital Imaging and Communication in Medicine") simulation

mode.This mode simulates the DICOM standard, which is a standard

applicable to digital communications in medicine.

ü This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to

establish wireless LAN connection.

ü The built-in 16W speaker can deliver sufﬁcient sound volume in a large

space like a classroom without external speakers.

ü This projector's network supports the PJLink™ standard.PJLink™ is a uniﬁed

standard for operating and controlling data projectors.For speciﬁcations of

PJLink™, see the web site of the PJLink™.

ü Equipped with IMAGE OPTIMIZER which is Hitachi's original function to

maintain visibility by automatic image correction in accordance with lamp

deterioration.

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise)

which is a book. Your projector should come with the items shown there. Require

of your dealer immediately if any items are missing.

NOTE • Keep the original packing materials, for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

Introduction

(2)

Part names

(1)

HOT!

Projector

(4)

(1) Lamp cover (98)

The lamp unit is inside.

(2) Control panel (5)

(3) Elevator feet (x 2) (25)

(4) Remote sensor (x 2)(18)

(5) projection window (102)

(6) Intake vents

(11)

(13)

(12)

(8)

(7) (6)

(7) Filter cover (100)

The air ﬁlter and intake vent

are inside.

(15)

(8) Speaker (12, 23, 53)

(9) Exhaust vent

(10) AC (AC inlet) (15)

(11) Ports (5)

(14)

(3)

(12) Security bar (15)

(13) Security slot (15)

(14) Spacer (x 2) (25)

(15) Battery cover (103)

(5)

(9)

HOT!

(10)

WARNING ►HOT! : Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Never look into the projection window while the projection lamp lights, since

the projection lamp ray may cause a trouble on your eyes.

►Do not use the security bar and slot to prevent the projector from falling down,

since it is not designed for it.

CAUTION

►Maintain normal ventilation to prevent the projector from

heating up. Do not cover, block or plug up the vents. Do not place anything that

can stick or be sucked to the vents, around the intake vents. Clean the air ﬁlter

periodically.

Introduction

Part names (continued)

Control panel

(1) STANDBY/ON button (20)

(2) INPUT button (24)

(3) POWER indicator (20, 107)

(4) TEMP indicator (107)

(5) LAMP indicator (107)

Buttons ◄/►/▲/▼

(4)

(5)

(3)

(6)

(6) FOCUS +/- buttons

(7)

(2)

(1)

when no menu is displayed (26), or

Cursor ◄/► buttons

when a menu is displayed (31). FOCUS +/- function is invalid when the

USB TYPE A port is selected as the input source.

(7) MENU buttons

when no menu is displayed (31), or

Cursor ▲/▼ buttons

when a menu is displayed (31).

The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the

template is displayed (58).

Ports (9 ~ 14)

(1) USB TYPE A port (x2)

(2) LAN port

(3) USB TYPE B port

(4) HDMI port (x2)

(5) MIC port

(9) COMPUTER IN1 port

(10) COMPUTER IN2 / MONITOR OUT port

(11) VIDEO IN port

(12) CONTROL port

(6) AUDIO IN1 port

(7) AUDIO IN2(L,R) ports

(8) AUDIO OUT port

(10)

(11)

(7)

(8)

(9)

(6)

(2)

(5)

(4)

(3)

(1)

(12)

Introduction

Part names (continued)

Remote control

(1) INPUT button (24)

(2) IWB button *

(3) CALIBRATION button *

(4) STANDBY/ON button (20)

(5) ASPECT button (24)

(6) AUTO button (26)

(7) ACCENTUALIZER button (27)

(8) HDCR button (27)

(9) FOCUS - button (26)

(10) FOCUS + button (26)

(11) D-ZOOM - button (25)

(12) D-ZOOM + button (25)

(13) PAGE UP button (19)

(14) MAGNIFY - ON button (29)

(15) MY BUTTON - 1 button (62)

(16) VOLUME + button (23)

(17) PAGE DOWN button (19)

(18) MAGNIFY - OFF button (29)

(19) MY BUTTON - 2 button (62)

(20) VOLUME - button (23)

(21) KEYSTONE/PERFECT FIT button (28)

(22) TEMPLATE button (27)

(23) FREEZE button (30)

(24) AV MUTE button (23)

(25) ESC button (31)

(2)

(1)

(6)

(5)

(10)

(9)

(13)

(14)

(17)

(18)

(21)

(22)

(25)

(30)

(28)

(3)

(4)

(7)

(8)

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

(11)

(12)

(16)

(15)

(20)

(19)

(24)

(23)

(26)

(27)

(29)

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

ENTER

POSITION

RESET

(31)

(26) MENU button (31, 32)

(27) ENTER button (31, 32)

(28) POSITION button (28, 32)

(29) RESET button (31)

Back of

the remote control

(30) ▲/▼/◄/► cursor buttons (31)

(31) Battery cover (17)

NOTE • Any button marked with “*” is not supported on this projector (106).

Setting up

Install the projector according to the environment and manner the projector will be

used in.

Arrangement

Refer to table T-1 or T-2 and ﬁgures F-1 and F-2 at the end of User’s Manual (concise) to

determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen.

b1 , b2

c1 c2

Screen height (±8%)

Screen size (diagonal)

Projection distance (±8%)

• For the case of installation in special conditions such as on the wall or ceiling, the

speciﬁed mounting accessories and service may be required. Tabletop use must be

setup with the designated optional accessories. Before installing the projector, consult

your dealer about your installation.

•

The screen position may shift after installation if the projector is mounted on locations

such as the wall or ceiling, due to the ﬂexibility of the plastic projector body. If readjustment

is necessary, consult with your dealer or service personnel.

• The projected image position and/or focus may change during warm-up (approx. 30

minutes after the lamp is turned on) or when the ambient conditions change. Readjust

the image position and/or focus as necessary.

• Since the projector features an ultra short throw, be aware that it is required to select a

screen carefully to have better performance.

- A soft screen such as a pull-down screen may cause serious distortion of a projected

image. A hard screen such as a board screen is recommended for use with this

projector.

- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable

for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide

viewing angle is recommended for use with this projector.

A screen with a weave pattern may cause moiré on the projected image, which is not a

failure of the projector. A screen that has less moiré effects is recommended for use with this

projector.

WARNING ►Place the projector in a stable horizontal position. If the

projector falls or is knocked over, it could cause injury and/or damage to the

projector. Using a damaged projector could then result in ﬁre and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side or front position. To place the projector

on its rear position for the table top use, it is required to use the designated

optional parts. Consult with your dealer.

• Consult with your dealer before a special installation such as on the wall or

ceiling.

(continued on next page)

Setting up

Arrangement (continued)

WARNING ►Place the projector in a cool place, and ensure that there is

sufﬁcient ventilation. The high temperature of the projector could cause ﬁre,

burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place or attach anything that would block the projection window or vent

holes.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

•

Do not place anything near the projection window or vents, or on top of the

projector.It causes high temperature and could result in ﬁre or smoke.

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom.

•

►Do not place the projector anyplace where it may get wet. Getting the projector

wet or inserting liquid into the projector could cause ﬁre, electric shock and/or

malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

•

►

Do not place the projector where any oils, such as cooking or machine oil, are used.

Use only the mounting accessories the manufacturer speciﬁed, and leave installing

and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place.

Placing the projector in such places could cause ﬁre, electric shock and/or

malfunction of the projector.

• Do not place the projector near humidiﬁers, smoking spaces or a kitchen. Also

do not use an ultrasonic humidiﬁer near the projector. Otherwise chlorine and

minerals contained in tap water are atomized and could be deposited in the

projector causing image degradation or other problems.

►Position the projector to prevent light from directly hitting the projector's remote sensor.

►Do not place the product in a place where radio interference may be caused.

►Do not place this product in a magnetic ﬁeld.

►

If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE

of the SERVICE item in the OPTION menu to HIGH (66). Otherwise, set it to

NORMAL.

If the projector is used with a wrong setting, it may cause damage to the projector

itself or the parts inside.

(continued on next page)

Setting up

Arrangement (continued)

NOTE

• The projector may make a rattling sound when tilted, moved or

shaken, since a ﬂap to control the air ﬂow inside of the projector has moved. Be

aware that this is not a failure or malfunction.

• The incoming light to the screen from the projector has a large angle. While

the white image is on the screen, you may see it with colors, but this is because

of the type of the screen used or the angles viewed, and it is not a malfunction.

• When the ambient temperature is around 35 to 40°C, the brightness of lamp

is reduced automatically.

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conﬁrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the device and projector are turned off, connect them

following the instructions below.

WARNING ►Use only the appropriate accessories. Otherwise it could cause

a ﬁre or damage to the device and the projector.

- Use only the accessories specified or recommended by the projector’s

manufacturer. Consult your dealer when the required accessory did not come

with the product or the accessory is damaged. It may be regulated under some

standard.

- For a cable with a core at only one end, connect the end with the core to the

projector. That may be required by EMI regulations.

- Neither disassemble nor modify the projector and the accessories.

- Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION ►Do not turn on or off the projector while connected to a device

in operation, unless that is directed in the manual of the device. Otherwise it may

cause malfunction in the device or projector.

►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it

may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ﬁts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of the

projector are recessed.

(continued on next page)

Setting up

Connecting with your devices (continued)

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system

and peripheral equipment (i.e. display devices). This projector is VESA DDC

2B compatible. Plug-and-Play can be used by connecting this projector to a

computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work

properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug-and-

Play monitor.

• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in

COMPUTER IN of the INPUT menu, that port will accept component video

signals (45).

•

When the USB TYPE B port and the computer's type A USB port are connected,

you can use the USB TYPE B port as a picture input port from the computer, or use

the remote control as a simple mouse and keyboard of the computer. (19).

Computer

VCR/DVD/Blu-ray Disc

player

(continued on next page)

Setting up

Connecting with your devices (continued)

NOTE • Before connecting the projector to a computer, consult the computer’s

manual and check the compatibility of the signal level, the synchronization

methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution

before being displayed. The best display performance will be achieved if the

resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display

and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (45).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display

device. You may be able to see the dialog and set an appropriate display

resolution.

(continued on next page)

Setting up

Connecting with your devices (continued)

• If you insert a USB storage device, such as a USB memory, into the USB TYPE

A port and select the port as the input source, you can view images stored in the

device (80).

• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug.

In that case, the built-in speaker outputs the sound from the microphone, even

while the sound from the projector is output. You can input line level signal to the

MIC port from equipment such as wireless microphone. In the normal mode, the

volume of the microphone can be adjusted separately from the volume of the

projector using the menu. (53)

In the standby mode, the volume of the microphone is adjustable with the

VOLUME +/- buttons on the remote control, in synchronization with the volume of

the projector. (23)

Even when the sound of projector is set to mute mode by the AUDIO SOURCE

function (53), the volume of the microphone is adjustable.

In both modes (standby or normal), the AV MUTE button on the remote control

works on the sounds of the microphone and the projector. (23)

Speakers

Monitor

(with an ampliﬁer)

Microphone

system

RGB IN

NOTE

• If a loud feedback noise is produced from the speaker, move the

microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

(continued on next page)

Setting up

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the

computer's LAN port, or with an access point that is connected to the computer

with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function,

also connect the CONTROL port and an RS-232C port of the external device to

communicate as a network terminal. See the User's Manual - Network Guide for

details of the network functions.

Computer

Access point

RS-232C

USB TYPE A

LAN

USB

wireless

adapter

(optional)

USB storage

device

CAUTION

to obtain the consent of the administrator of the network.

Do not connect the LAN port to any network that might have the excessive voltage.

►Before connecting the projector to a network system be sure

►

►The designated USB wireless adapter that is sold as an option is required to

use the wireless network function of this projector.

►Before removing the USB storage device from the port of the projector, be

sure to use the REMOVE USB function on the thumbnail screen to secure your

data (83).

►Do not use any extension cable or device when connecting the adapter to

the projector. Before you insert or pull out the USB wireless adapter from the

projector, turn off the power of the projector and pull out the power cord’s plug

from the outlet. Do not touch the USB wireless adapter while the projector is

receiving AC power.

►To connect both the LAN cable and USB device to the projector, use a LAN

cable that is ﬂat on the side where the plug’s wire is visible. Otherwise, both of

them cannot be connected correctly, or the wire may break (malfunction).

(continued on next page)

Setting up

Connecting with your devices (continued)

NOTE • If an oversized USB storage device blocks the LAN port, use a USB

extension cable to connect the USB storage device.

• The HDMI port of this model is compatible with HDCP (High-bandwidth Digital

Content Protection) and therefore capable of displaying a video signal from

HDCP compatible DVD players or the like.

- The HDMI supports the following signals.

Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,

1080i@50/60, 1080p@50/60

Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMI^TM

connector, but with some equipment the projector may not work properly,

something like no video.

- Be sure to use an HDMI^TMcable that has the HDMI^TMlogo.

- Use a Category 2-certiﬁed HDMI^TMcable to input 1080p@50/60 signal to the

projector.

- When the projector is connected with a device having DVI connector, use a

DVI to HDMI^TMcable to connect with the HDMI input.

• Up to one USB wireless adapter (optional) can be connected to a projector.

Setting up

Connecting to a power supply

Put the connector of the power cord into the

AC (AC inlet) of the projector.

Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the

power supply connection, the POWER

indicator will light up in steady orange.

Please remember that when the DIRECT POWER

ON function activated (60), the connection of the

power supply make the projector turn on.

Power cord

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in ﬁre and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible.

Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in ﬁre, electric shock

or other accidents.

• Do not press the main body of projector on the power cord.

Using the security bar and slot

A commercial anti-theft chain or wire up to

10 mm in diameter can be attached to the

security bar on the projector.

Also this product has the security slot for

the Kensington lock.

For details, see the manual of the security

Security slot

tool.

Security bar

Anti-theft chain or wire

WARNING ►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

CAUTION ►Do not place anti-theft chain or wire near the exhaust vents.

It may become too hot.

NOTE • The security bar and slot is not comprehensive theft prevention

measures. It is intended to be used as supplemental theft prevention measure.

Setting up

Using the cable cover

Utilize the cable cover as the guard and blind for the connecting parts.

1. ^{Connect the signal cables and the power cord to the projector ﬁrst.}

Insert the three knobs on the cable cover into the

three holes on the projector as shown in the ﬁgure.

Pass the cables through the holes on the bottom of

the cable cover.

knobs

3 ^{Fix the cover's screw.}

screw

CAUTION ► Be careful not to pinch the cables in the cable cover, to

prevent damage to the cables.

► Use the cable cover that is supplied with the projector. Do not attempt any

modiﬁcations to the cable cover.

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control

starts to malfunction, try to replace the batteries. If you will not use the remote control for

long period, remove the batteries from the remote control and store them in a safe place.

1. ^{Remove the battery cover.}

Align and insert the two AA batteries (HITACHI MAXELL ,

Part No.LR6 or R6P) according to their plus and minus

terminals as indicated in the remote control.

3. ^{Put the battery cover back to the former state.}

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in ﬁre, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speciﬁed. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a ﬁre or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery.

If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

Remote control

Remote

sensor

About the remote control signal

The remote control works with the projector’s remote

sensor. This projector has a remote sensor on the front.

The sensor senses the signal within the following range

when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor)

within 3 meters about.

Approx.

3 m

30º

NOTE • You can deactivate one of the sensors using the REMOTE RECEIV.

item in the SERVICE menu of the OPTION menu (67) .

•

The remote control signal reﬂected in the screen or the like may be available. If it is

difﬁcult to send the signal to the sensor directly, attempt to make the signal reﬂect.

• The remote control uses infrared light to send signals to the projector (Class 1

LED), so be sure to use the remote control in an area free from obstacles that

could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun

light) or light from an extremely close range (such as from an inverter ﬂuorescent

lamp) shines on the remote sensor of the projector. Adjust the position of

projector avoiding those lights.

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal

INPUT

IWB

CALIBRATION

frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote

control does not function properly, attempt to change the

signal frequency.

ASPECT

AUTO

ACCENTUALIZER HDCR

FOCUS

D-ZOOM

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

In order to set the Mode, please keep pressing the

combination of two buttons listed below simultaneously for

about 3 seconds.

(2)

(1)

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

ENTER

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons

POSITION

RESET

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

Please remember that the REMOTE FREQ. in the SERVICE

item of the OPTION menu

(68) of the projector to be

controlled should be set to the same mode as the remote

control.

Remote control

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse

and keyboard of the computer, when the projector’s USB

TYPE B port and the computer’s type A USB port are

connected.

USB TYPE B

port

(1) PAGE UP key: Press PAGE UP button.

(2) PAGE DOWN key: Press PAGE DOWN button.

(3) Mouse left button: Press ENTER button.

(4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.

(5) ESC key: Press ESC button.

INPUT

IWB

CALIBRATION

(1)

(2)

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

(6) Mouse right button: Press RESET button.

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

(5)

(3)

(4)

(6)

ESC

►Improper use of the simple mouse & keyboard

NOTICE

ENTER

function could damage your equipment. While using this

function, please connect this product only to a computer. Be

sure to check your computer’s manuals before connecting this

product to the computer.

POSITION

RESET

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing

device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external

mouse and disable the built-in pointing device, because the built-in pointing device may

have priority to this function.

•

Windows XP SP3 or higher is required for this function. And also this function may not work

depending on the computer’s conﬁgurations and mouse drivers. This function can work with the

computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons

at the same time to move the mouse pointer diagonally).

•

This function is activated only when the projector is working properly. This function is not

available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

- When either USB TYPE A or USB TYPE B port is selected.

- While displaying BLANK (23), TEMPLATE (58) or MY IMAGE screen.

- When any menu is displayed on the screen.

While using the cursor buttons to operate the sound or screen functions such as adjusting the

sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

Power on/off

Turning on the power

STANDBY/ON button

POWER indicator

Make sure that the power cord is ﬁrmly

and correctly connected to the projector

and the outlet.

Make sure that the POWER indicator is

steady orange (107).

Press STANDBY/ON button on the

projector or the remote control. The

INPUT

IWB

CALIBRATION

ASPECT

AUTO ACCENTUALIZER HDCR

projection lamp lights up, and the POWER

indicator begins to blink green. When the

power is completely on, the indicator will

stop blinking and light in steady green

(107).

FOCUS

D-ZOOM

PAGE

MAGNIFY

MYBUTTON

VOLUME

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

ENTER

POSITION

RESET

To display the picture, select an input signal according to the section Selecting an

input signal (24).

The INITIAL SETTING Menu will be displayed by factory default upon startup.

Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET

(73) is executed. If you wish to change the settings, refer to the LANGUAGE

(54) and ALTITUDE (66) menu.

(1) LANGUAGE: Use the ▲/▼/◄/►

buttons to select the desired language

and press the ENTER button of the

remote control or the INPUT button of

the projector to execute.

(2) ALTITUDE: Use the ▲/▼ buttons to

select NORMAL for altitude below 1600

m (5250 feet), otherwise select HIGH

and press the ENTER button of the

remote control or the INPUT button of

the projector to execute.

(continued on next page)

Power on/off

WARNING ►Never look into the projection window while the

projection lamp lights, since the projection lamp ray may cause a

trouble on your eyes.

►Do not place the projector vertically as shown in the ﬁgure on

the right. It could cause malfunction or injury. Tabletop use must be

setup with the designated optional accessories.

►The projection window of this machine is made of glass. It can be

damaged by excessive force or an impact. Read the following

important warnings carefully, and follow them for your own safety.

• Do not apply excessive force on or allow impact to the projection

window.

• Keep the projector out of the reach of children.

• If the projection window is broken, the projected image will be

distorted. Never touch a broken projection window, and contact your

dealer.

Power on/off

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in

orange. Then POWER indicator will stop blinking and light in steady orange

when the lamp cooling is complete (107).

Do not turn the projector on for about 10 minutes or more after turning it off.

Also, do not turn the projector off shortly after turning it on. Such operations might

cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

►Do not touch around the lamp cover and the exhaust vents

during use or just after use, since it is too hot.

WARNING

►Remove the power cord for complete separation. The power outlet should be

close to the projector and easily accessible.

NOTE • Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/

off. Please refer to the DIRECT POWER ON (60) and AUTO POWER OFF (61)

items of the OPTION menu.

Operating

VOLUME +/- button

Adjusting the volume

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

Use the VOLUME +/VOLUME - buttons to adjust the volume.

FOCUS

A dialog will appear on the screen to aid you in adjusting the

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

volume. If you do not do anything, the dialog will automatically

disappear after about ten seconds.

ー

DOWN

OFF

KEYSTONE/

● When is selected for current picture input port, the volume adjustment is

disabled. Please see AUDIO SOURCE item of AUDIO menu (53).

● Even if the projector is in the standby mode, the volume is adjustable when

both of the following conditions are true:

- An option other than is selected for STANDBY in the AUDIO SOURCE

item of the AUDIO menu (53).

NORMAL is selected in the STANDBY MODE item of the SETUP menu (52).

● In the standby mode, the volume of the microphone is adjustable with the

VOLUME +/- buttons on the remote control, in synchronization with the volume

of the projector (12).

Temporarily muting the screen and audio output

AV MUTE button

INPUT

IWB

CALIBRATION

Press AV MUTE button on the remote control.

1. _{The BLANK screen will be displayed instead of the screen of}

ASPECT

AUTO

ACCENTUALIZER HDCR

FOCUS

D-ZOOM

input signals and the sound from the AUDIO OUT port will be

muted. Please refer to the BLANK item in SCREEN menu about

the BLANK screen (54).

To exit from the AV MUTE mode and restore the screen and

audio, press AV MUTE button again.

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

NOTE

• The projector automatically exits from the AV MUTE mode

when some control buttons are pressed.

The audio is output from the external audio system connected to

the AUDIO OUT port.

•

WARNING

►If you wish to have a blank screen while the projector's lamp

is on, use the AV MUTE function above .

Taking any other action may cause the damage on the projector.

Blocking the beam by something causes high temperature and could result in

ﬁre or smoke.

Operating

INPUT button

Selecting an input signal

INPUT button

Press INPUT button on the projector.

Each time you press the button, the

projector switches its input port from

the current port as below.

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

FOCUS

D-ZOOM

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

COMPUTER IN1 COMPUTER IN2

VIDEO

LAN

HDMI

USB TYPE A



HDMI 1

USB TYPE B

●

While ON is selected for AUTO SEARCH item in OPTION menu (60), the projector

will keep checking the ports in above order repeatedly till an input signal is detected.

It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

ASPECT button

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the

mode for aspect ratio in turn.

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

For a computer signal

FOCUS

D-ZOOM

NORMAL 4:3 16:9 16:10 NATIVE

PAGE

MAGNIFY

MYBUTTON

VOLUME

＋

ー

DOWN

OFF

For an HDMI^TMsignal

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

NORMAL 4:3 16:9 16:10 14:9 NATIVE

For a video signal or component video signal

4:3 16:9 16:10 14:9 NATIVE

For an input signal from the LAN, USB TYPE A or USB TYPE B port, or

if there is no signal

CP-AX2505, CP-AX3005, CP-AX3505: 4:3 (ﬁxed)

CP-AW2505, CP-AW3005: 16:10 (ﬁxed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

● The on-screen menu might be displayed outside of the image display area

depending on the adjustment value of the ASPECT, D-ZOOM,

KEYSTONE and PERFECT FIT. Changing the values of ASPECT, D-ZOOM,

KEYSTONE, KEYSTONE and PERFECT FIT may ﬁx the symptom.

KEYSTONE,

Operating

Adjusting the projector's elevator

The projector has 2pcs Rear foot for horizontals and inclinations. Spacers on

the each elevator foot are installed at the time of shipment, and projector is in a

condition to be able to just project. If necessary, detach the spacer, and the elevator

feet can be manually twisted to make more precise adjustments.

-1~1°

Rear foot

Spacer

-1~1°

Rear foot

WARNING ►Keep the spacers away from children and pets. Be careful not

to let them swallow the spacers. If swallowed, consult a physician immediately

for emergency treatment.

NOTE • The adjustment angle can be adjusted up to plus or minus 1° each of

foot.

•

After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer.

If change the setting place of the projector, it will recommend keep and reuse the

spacers.

Adjusting the zoom and focus

Press the D-ZOOM + or D-ZOOM - button on the remote

D-ZOOM - button

control to display D-ZOOM dialog on screen.

INPUT

IWB

CALIBRATION

Use the D-ZOOM + and D-ZOOM - buttons to adjust the

picture size.

ASPECT

AUTO

ACCENTUALIZER HDCR

FOCUS

D-ZOOM

PAGE

VOLUME

MAGNIFY

MYBUTTON

To ﬁnish the operation, do not touch these buttons for about

ten seconds until the dialog is disappeared.

● If you want to expand a part of the image, use the magnify

function (29).

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

D-ZOOM + button

(continued on next page)

Operating

FOCUS - button

Press the FOCUS + or FOCUS - button on the remote

control, or FOCUS + or FOCUS - button on the projector (5)

while no menu is on screen, to display the FOCUS box on

screen. Use the FOCUS + and FOCUS - buttons to adjust

the screen focus. After the focus adjustment, wait for a while

until the FOCUS box is disappeared, if you want to display

any other menu on screen by pushing the MENU button on

the projector.

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

FOCUS

D-ZOOM

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

● The ◄/►/▲/▼ buttons on the projector work only as the

cursor buttons while the template is displayed (58).

FOCUS + button

Using the automatic adjustment feature

AUTO button

Press AUTO button on the remote control.

Pressing this button performs the following.

INPUT

IWB

CALIBRATION

For a computer signal

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

The vertical position, the horizontal position and the horizontal

phase will be automatically adjusted.

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

Make sure that the application window is set to its maximum size

prior to attempting to use this feature. A dark picture may still be

incorrectly adjusted. Use a bright picture when adjusting.

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

For a video signal

The video format best suited for the respective input signal will be selected

automatically. This function is available only when the AUTO is selected for

the VIDEO FORMAT item in the INPUT menu (44). The vertical position and

horizontal position will be automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically set to the default.

The horizontal phase will be automatically adjusted.

● The automatic adjustment operation requires approx. 10 seconds. Also please

note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line

may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be

displayed on the edge of the screen, depending on the PC model.

●

The items adjusted by this function may vary when the FINE or DISABLE is selected

for the AUTO ADJUST item of the SERVICE item in the OPTION menu (66).

Operating

Using the TEMPLATE feature

Press TEMPLATE button on the remote control.

Each time you press the button, the projector switches the

mode for TEMPLATE in turn.

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

TEST PATTERN DOT-LINE1 DOT-LINE2 DOT-LINE3

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

HAS-WM05

HAS-WM03

DOT-LINE4



TEMPLATE button

MAP2

MAP1

CIRCLE2

CIRCLE1

● TEMPLATE button does not work when no proper signal is inputted.

Other buttons

HDCR: Displays the HDCR menu (36).

ACCENTUALIZER: Displays the ACCENTUALIZER menu (36).

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

button

ACCENTUALIZER

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

HDCR button

Operating

Adjusting the position

ESC

Press the POSITION button on the remote control while no menu

ENTER

is on screen, to display the D-SHIFT (47) dialog on screen.

POSITION

RESET

Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.

Press the POSITION button again to ﬁnish this operation.

POSITION button

● This is a function to shift the position of the shrunken picture by the D-ZOOM (47)

function.

● When an OSD (On Screen Display) menu is displayed, this operation moves the

position of the OSD menu, but not the position of the picture (32)

● The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 256 (full

screen). (CP-AX2505, CP-AX3005, CP-AX3505)

● The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full

screen). (CP-AW2505, CP-AW3005)

Correcting the keystone/perfect ﬁt distortions

Press KEYSTONE/PERFECT FIT button

KEYSTONE/

PERFECT FIT

button

on the remote control. A dialog will appear

on the screen to aid you in correcting the

distortion.

Use the ▲/▼ cursor buttons to select MANUAL or PERFECT

FIT operation, and press the ► button to perform the following.

(1) MANUAL displays a dialog for keystone correction.

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

Use the ▲/▼ buttons to select

KEYSTONE, then use the ◄/► buttons for

adjustment.

KEYSTONE /

＋

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

(2) PERFECT FIT displays a dialog for adjusting the shape

of the projected image in each of the corners and sides.

To close the dialog and complete this operation, press

KEYSTONE/PERFECT FIT button again. Even if you do not do

anything, the dialog will automatically disappear after about ten

seconds.

● The adjustable range of this function will vary among inputs. For some input,

this function may not work well.

Operating

Using the magnify feature

MAGNIFY

Press the MAGNIFY ON button on the remote control.

The picture will be magniﬁed, and the MAGNIFY dialog will

appear on the screen. When the MAGNIFY ON button is

pressed for the ﬁrst time after the projector is turned on, the

picture will be zoomed by 1.5 times. On the dialog, triangle

marks to show each direction will be displayed.

ON/OFF button

INPUT

IWB

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

The display magniﬁcation of the projector switches in order

with every press of the MAGNIFY ON button.

For computer signals, HDMI^TM(RGB) signals, input signals from the

LAN, USB TYPE A or USB TYPE B port

1.5 times 2 times 3 times 4 times 1 time



For video signals, component video signals or HDMI^TM(Component)

signals

1.5 times 2 times 1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

4. ^{Press the MAGNIFY OFF button on the remote control to exit magniﬁcation.}

● The MAGNIFY dialog will automatically disappear in several seconds with no

operation. The dialog will appear again if the MAGNIFY ON button is pressed

when the dialog has automatically disappeared.

● The magniﬁcation is automatically disabled when the displaying signal or its

display condition is changed.

● While the magniﬁcation is active, the keystone distortion condition may vary.

It will be restored when the magniﬁcation is disabled.

● Some horizontal stripes might be visible on the image while magniﬁcation is

active.

● This function is not available in the following cases:

- A sync signal in the range not supported is input.

- There is no input signal.

Operating

Temporarily freezing the screen

FREEZE button

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however,

INPUT

IWB

CALIBRATION

the indication will not appear when the OFF is selected for

the MESSAGE item in the SCREEN menu (56)), and the

projector will go into the FREEZE mode, which the picture is

frozen.

ASPECT

AUTO

ACCENTUALIZER HDCR

D-ZOOM

FOCUS

PAGE

VOLUME

MAGNIFY

MYBUTTON

＋

ー

DOWN

OFF

To exit the FREEZE mode and restore the screen to normal,

press the FREEZE button again.

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

● The projector automatically exits from the FREEZE mode when some control

buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD

panel might possibly be burned in. Do not leave the projector in the FREEZE

mode for too long.

● Images might appear degraded when this function is operated, but it is not a

malfunction.

Operating

Using the menu function

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK,

SECURITY and EASY MENU.

EASY MENU consists of functions often used, and the other menus are classiﬁed

into each purpose and brought together as the ADVANCED MENU.

Each of these menus is operated using the same methods. While the projector

is displaying any menu, the MENU button on the projector works as the cursor

buttons. The basic operations of these menus are as follows.

MENU button

ESC button

Cursor buttons

ESC

INPUT

IWB

CALIBRATION

ASPECT

AUTO ACCENTUALIZER HDCR

FOCUS

D-ZOOM

PAGE

MAGNIFY

MYBUTTON

VOLUME

＋

ENTER

ー

DOWN

OFF

KEYSTONE/

PERFECT FIT TEMPLATE

FREEZE

AV MUTE

ESC

ENTER

MENU button

(Cursor buttons)

POSITION

RESET

POSITION

RESET

RESET button

ENTER button

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after

powered on.

2. ^{In the EASY MENU}

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED

MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select

the EASY MENU.

The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the

▲/▼ cursor buttons to select an item to operate and press the ► cursor

button or ENTER button to progress. The operation menu or dialog of the

selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

(continued on next page)

Operating

Using the menu function (continued)

To close the MENU, press the MENU button again or select EXIT and press

the ◄ cursor button or ENTER button. Even if you do not do anything, the

dialog will automatically disappear after about 30 seconds.

●

If you want to move the menu position, use the cursor buttons after pressing the

POSITION button.

● Some functions cannot be performed when a certain input port is selected, or

when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote

control during the operation. Note that some items (ex. LANGUAGE, VOLUME)

cannot be reset.

● In the ADVANCED MENU, when you want to return to the previous display,

press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication

EXIT

Meaning

Selecting this word ﬁnishes the OSD menu. It's the same as

pressing the MENU button.

RETURN

Selecting this word returns the menu to the previous menu.

Selecting this word cancels the operation in the present

menu and returns to the previous menu.

CANCEL or NO

Selecting this word executes the prepared function or shifts

the menu to the next menu.

OK or YES

EASY MENU

From the EASY MENU, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons. Then

perform it according to the following table.

Item

Description

Using the ◄/► buttons switches the mode for aspect ratio.

ASPECT

See the ASPECT item in IMAGE menu ( 40).



Using the ◄/► cursor buttons adjusts the magniﬁcation ratio.

Small

Large

See the D-ZOOM item in the SETUP menu ( 47).



• The on-screen menu might be displayed outside of the image

display area depending on the adjustment value of the ASPECT,

D-ZOOM

D-ZOOM,

of ASPECT, D-ZOOM,

the symptom.

KEYSTON and

KEYSTONE. Changing the values

KEYSTONE and KEYSTONE may ﬁx

Using the ◄/► buttons corrects the vertical keystone distortion.

See the KEYSTONE item in SETUP menu ( 48).

KEYSTONE



Using the ◄/► buttons corrects the horizontal keystone distortion.

See the KEYSTONE item in SETUP Menu ( 48).



Pressing the ► button displays the dialog for adjusting the shape

of the projected image in each of the corners and sides. See the

PERFECT FIT

PERFECT FIT item in SETUP menu ( 49).



(continued on next page)

EASY MENU

Item

Description

Using the ◄/► buttons switches the picture mode.

The picture modes are combinations of GAMMA and COLOR TEMP

settings. Choose a suitable mode according to the projected source.

NORMAL

CINEMA

DYNAMIC

BOARD(BLACK)

DICOM SIM.

PHOTO

DAYTIME

WHITEBOARD

BOARD(GREEN)

• When the combination of GAMMA and COLOR TEMP differs

from pre-assigned modes above, the display on the menu for the

PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and

PICTURE MODE

COLOR TEMP ( 37, 38) items in PICTURE menu.



• Lines or other noise might appear on the screen when this function

is operated, but it is not a malfunction.

• DICOM SIM. is the projector's DICOM^®("Digital Imaging and

Communication in Medicine") simulation mode. This mode

simulates the DICOM standard, which is a standard applicable to

digital communications in medicine, and can be useful for displaying

medical images, such as X-rays photos. This projector is not a

medical device and is not compliant to the DICOM standard, and

neither the projector nor the DICOM SIM. mode should be used for

medical diagnosis.

Using the ◄/► buttons changes the eco mode setting.

See the ECO MODE item of the LAMP & FILTER item in SETUP

ECO MODE

menu. ( 50)



• When the ambient temperature is around 35 to 40°C, the

brightness of lamp is reduced automatically.

Pressing the ► button displays the INSTALLATION dialog.

INSTALLATION

RESET

See the INSTALLATION item in SETUP menu ( 52).



Performing this item resets all of the EASY MENU items except the

FILTER TIME and LANGUAGE.

A dialog is displayed for conﬁrmation. Selecting the OK using the ►

button performs resetting.

The usage time of the air ﬁlter is shown in the menu.

Performing this item resets the ﬁlter time which counts usage time

of the air ﬁlter.

A dialog is displayed for conﬁrmation. Selecting the OK using the ►

button performs resetting.

FILTER TIME

See the FILTER TIME item of the LAMP & FILTER item in SETUP

menu. ( 51)



(continued on next page)

EASY MENU

Item

Description

Using the ◄/► buttons changes the display language.

LANGUAGE

See the LANGUAGE item in SCREEN menu ( 54).



Press the ► or ENTER button to use the menu of PICTURE,

ADVANCED MENU IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or

SECURITY.

EXIT

Press the ◄ or ENTER button to ﬁnish the OSD menu.

PICTURE menu

From the PICTURE menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and press

the ► cursor button or ENTER button to execute the

item. Then perform it according to the following table.

Item

Description

Using the ◄/► buttons adjusts the brightness.

BRIGHTNESS

Dark

Light

Using the ◄/► buttons adjusts the contrast.

Weak Strong

CONTRAST

HDCR

A function to show a clear picture in a bright room.

Using the◄/► buttons adjusts the contrast.

• This function may not work properly when IMAGE OPTIMIZER is

enabled.

ACCENTUALIZER is a function to improve the legibility.

Using the ◄/► buttons adjusts the sharpness.

Weak

Strong

ACCENTUALIZER • There may be some noise and/or the screen may ﬂicker for a

moment when an adjustment is made. This is not a malfunction.

• This function may not work properly when IMAGE OPTIMIZER is

enabled.

(continued on next page)

PICTURE menu

Item

Description

Using the ▲/▼ buttons switches the gamma mode.

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then

pressing the ► button or the ENTER button displays

a dialog to aid you in adjusting the mode.

This function is useful when you want to

change the brightness of particular tones.

Choose an item using the ◄/► buttons,

and adjust the level using the ▲/▼ buttons.

You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button.

Each time you press the ENTER button, the

pattern changes as below.

GAMMA

No pattern Gray scale of 9 steps

Ramp Gray scale of 15 steps



The eight equalizing bars correspond to eight tone levels of the test

pattern (Gray scale of 9 steps) except the darkest in the left end. If you

want to adjust the 2nd tone from left end on the test pattern, use the

equalizing adjustment bar “1”. The darkest tone at the left end of the

test pattern cannot be controlled with any of equalizing adjustment bar.

• Lines or other noise might appear on the

screen when this function is operated, but it

is not a malfunction.

(continued on next page)

PICTURE menu

Item

Description

Using the ▲/▼ buttons switches the color temperature mode.

To adjust CUSTOM

Selecting a mode whose name includes

CUSTOM and then pressing the ► button

or the ENTER button displays a dialog

to aid you in adjusting the OFFSET and

GAIN of the selected mode.

OFFSET adjustments change the color intensity on the whole tones

of the test pattern.

GAIN adjustments mainly affect color intensity on the brighter tones

of the test pattern.

COLOR TEMP

Choose an item using the ◄/► buttons, and adjust the level using

the ▲/▼ buttons.

You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button.

Each time you press the ENTER button, the pattern changes as below.

No pattern Gray scale of 9 steps

Ramp Gray scale of 15 steps



• Lines or other noise might appear on the screen

when this function is operated, but it is not a

malfunction.

Using the ◄/► buttons adjusts the strength of whole color.

Weak

Strong

• This item can be selected only for a video and component video

signal.

•

COLOR

For an HDMI^TMsignal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

Using the ◄/► buttons adjusts the tint.

Reddish

Greenish

• This item can be selected only for a video and component video

signal.

•

TINT

For an HDMI^TMsignal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

(continued on next page)

PICTURE menu

Item

Description

Using the ◄/► buttons adjusts the sharpness.

Weak

Strong

SHARPNESS

• There may be some noise and/or the screen may ﬂicker for a

moment when an adjustment is made. This is not a malfunction.

Using the ▲/▼ cursor buttons changes the active iris control mode.

PRESENTATION

THEATER

OFF

PRESENTATION : The active iris displays the best presentation

image for both bright and dark scenes.

THEATER : The active iris displays the best theater image for

both bright and dark scenes.

ACTIVE IRIS

OFF : The active iris is always open.

• The screen may ﬂicker when the PRESENTATION or THEATER

modes are selected. If this occurs select OFF.

This projector has 4 memories for adjustment data (for all the items

of the PICTURE menu).

Selecting a function using the ▲/▼ buttons and pressing the ► or

ENTER button performs each function.

SAVE-1

SAVE-2

SAVE-3

SAVE-4

LOAD-4 LOAD-3

LOAD-2

LOAD-1

SAVE-1, SAVE-2, SAVE-3, SAVE-4

Performing a SAVE function saves the current adjustment data into

the memory linked in the number included in the function’s name.

• Remember that the current data being stored of a memory will be

lost by saving new data into the memory.

MY MEMORY

LOAD-1, LOAD-2, LOAD-3, LOAD-4

Performing a LOAD function loads the data from the memory linked

in the number included in the function’s name, and adjusts the

picture automatically depending on the data.

• The LOAD functions whose linked memory has no data are

skipped.

• Remember that the current adjusted condition will be lost by

loading data. If you want to keep the current adjustment, please

save it before performing a LOAD function.

• There may be some noise and the screen may ﬂicker for a

moment when loading data. This is not malfunction.

• You can perform the LOAD function using MY BUTTON. Please

see MY BUTTON item in OPTION menu ( 62).



IMAGE menu

From the IMAGE menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item

Description

Using the ▲/▼ buttons switches the mode for aspect ratio.

For a computer signal

NORMAL

4:3 NATIVE

16:9

16:10

ó ó ó ó

For an HDMI^TMsignal

NATIVE

ó ó ó ó ó

NORMAL

4:3 16:9 16:10 14:9

ASPECT

For a video signal or component video signal

4:3 16:9 16:10 14:9 NATIVE

ó ó ó ó

For an input signal from the LAN, USB TYPE A or USB TYPE B

port, or if there is no signal

CP-AX2505, CP-AX3005, CP-AX3505: 4:3 (ﬁxed)

CP-AW2505, CP-AW3005: 16:10 (ﬁxed)

• The NORMAL mode keeps the original aspect ratio of the signal.

Using the ◄/► buttons adjusts the over-scan ratio.

Small (It magniﬁes picture)

Large (It reduces picture)

• This item can be selected only for a video and component video

signal.

• For an HDMI^TMsignal, this item can also be selected if either (1) or

(2) applies.

OVER SCAN

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

(continued on next page)

IMAGE menu

Item

Description

Using the ◄/► buttons adjusts the vertical position.

Down

• Over-adjusting the vertical position may cause noise to appear on

the screen. If this occurs, please reset the vertical position to the

default setting. Pressing the RESET button when the V POSITION

is selected will reset the V POSITION to the default setting.

• When this function is performed on a video signal, the range of

V POSITION

this adjustment depends on OVER SCAN ( 38) setting. It is not



possible to adjust when OVER SCAN is set to 10.

•

This function is unavailable for a signal from the LAN, USB TYPE A,

USB TYPE B or HDMI 1/2 port.

Using the ◄/► buttons adjusts the horizontal position.

Right

Left

•

Over-adjusting the horizontal position may cause noise to appear on

the screen. If this occurs, please reset the horizontal position to the

default setting. Pressing the RESET button when the H POSITION is

selected will reset the H POSITION to the default setting.

H POSITION

• When this function is performed on a video signal, the range of

this adjustment depends on OVER SCAN ( 40) setting. It is not



possible to adjust when OVER SCAN is set to 10.

•

This function is unavailable for a signal from the LAN, USB TYPE A,

USB TYPE B or HDMI 1/2 por

(continued on next page)

IMAGE menu

Item

Description

Using the ◄/► buttons adjusts the horizontal phase to eliminate ﬂicker.

Right

Left

H PHASE

• This item can be selected only for a computer signal or a

component video signal. This function is unavailable for a signal

from the LAN, USB TYPE A, USB TYPE B or HDMI 1/2 port.

Using the ◄/► buttons adjusts the horizontal size.

Small

Large

• This item can be selected only for a computer signal. This function

is unavailable for a signal from the LAN, USB TYPE A, USB TYPE

B or HDMI 1/2 port.

• When this adjustment is excessive, the picture may not be

displayed correctly. In such a case, please reset the adjustment

by pressing the RESET button on the remote control during this

operation.

H SIZE

• Images might appear degraded when this function is operated, but

it is not a malfunction.

Selecting this item performs the automatic adjustment feature.

For a computer signal

The vertical position, the horizontal position and the horizontal

phase will be automatically adjusted.

Make sure that the application window is set to its maximum size

prior to attempting to use this feature. A dark picture may still be

incorrectly adjusted. Use a bright picture when adjusting.

For a video signal

The video format best suited for the respective input signal will

be selected automatically. This function is available only when

the AUTO is selected for the VIDEO FORMAT item in the INPUT

menu ( 44).



The vertical position and horizontal position will be

automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically

set to the default. The horizontal phase will be automatically

adjusted.

AUTO ADJUST

EXECUTE

• The automatic adjustment operation requires approx. 10 seconds.

Also please note that it may not function correctly with some input.

• When this function is performed for a video signal, a certain extra

such as a line may appear outside a picture.

• When this function is performed for a computer signal, a black

frame may be displayed on the edge of the screen, depending on

the PC model.

• The items adjusted by this function may vary when the FINE or

DISABLE is selected for the AUTO ADJUST item of the SERVICE

item in the OPTION menu ( 66).



INPUT menu

From the INPUT menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item

Description

Using the ▲/▼ buttons switches the progress mode.

TV FILM OFF

ó ó

•

This function works only for a video signal, component video signal

(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI^TMsignal (of

480i@60 or 576i@50 or 1080i@50/60)

PROGRESSIVE

• When TV or FILM is selected, the screen image will be sharp.

FILM adapts to the 2-3 Pull-Down conversion system. But these

may cause a certain defect (for example, jagged line) of the picture

for a quick moving object. In such a case, please select OFF, even

though the screen image may lose sharpness.

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH

MID LOW

ó ó

VIDEO NR

• This function works only for a video signal, component video signal

(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI^TMsignal (of

480i@60 or 576i@50 or 1080i@50/60).

Using the ▲/▼ buttons switches the mode for color space.

AUTO

RGB

ó ó

SMPTE240

REC709

REC601

• This item can be selected only for a computer signal, component

video signal(except for signals from the LAN, USB TYPE A and

USB TYPE B ports) or an HDMI™ signal.

COLOR SPACE

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a

case, it might be good to select a suitable mode except AUTO.

(continued on next page)

INPUT menu

Item

Description

The video format for VIDEO IN port can be set.

Using the ◄/► buttons switches

the mode for video format.

AUTO

NTSC

PAL SECAM

ó ó

VIDEO FORMAT

N-PAL

M-PAL NTSC4.43

•

This item is performed only for a video signal from the VIDEO IN port.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the

picture becomes unstable (e.g. an irregular picture, lack of color),

please select the mode according to the input signal.

The video format of HDMI^TMinput signals from the HDMI 1 and 2

ports can be set.

(1) Use the ▲/▼ buttons to

select the HDMI port to be

set.

(2) Use the ◄/►buttons to select the video format.

AUTO

VIDEO

COMPUTER

HDMI FORMAT

AUTO: automatically sets the optimum mode.

VIDEO: sets the suitable mode for DVD signals.

COMPUTER: sets the suitable mode for computer signals.

• When the COMPUTER is selected, the functions COLOR

(PICTURE menu), TINT (PICTURE menu) and OVER SCAN

(IMAGE menu) are unavailable.

The digital range of HDMI^TMinput signals from the HDMI 1 and 2

ports can be set.

(1) Use the ▲/▼ buttons to

select the HDMI port to be

set.

(2) Use the ◄/►buttons to select the digital range.

HDMI RANGE

AUTO

NORMAL

ENHANCED

AUTO: automatically sets the optimum mode.

NORMAL: sets the suitable mode for DVD signals. (16-235)

ENHANCED: sets the suitable mode for computer signals. (0-255)

• If the contrast of the screen image is too strong or too weak, try

finding a more suitable mode.

(continued on next page)

INPUT menu

Item

Description

The computer input signal type for COMPUTER IN1 and IN2 ports

can be set.

(1) Use the ▲/▼ buttons to select the COMPUTER IN port to be

set.

(2) Use the ◄/► buttons to select

the computer input signal type.

(COMPUTER IN1)

AUTO

SYNC ON G OFF

COMPUTER IN

(COMPUTER IN2)

AUTO SYNC ON G OFF

MONITOR OUT

• Selecting the AUTO mode allows you to input a sync on G signal

or component video signal from the port ( 12).



• In the AUTO mode, the picture may be distorted with certain

input signals. In such a case, remove the signal connector so that

no signal is received and select the SYNC ON G OFF, and then

reconnect the signal.

Set the frame lock function on/off for each port.

(1) Use the ▲/▼ buttons to select

the input ports.

(2) Use the ◄/► buttons to turn the

frame lock function on/off .

OFF

FRAME LOCK

• This item can be performed only on a signal with a vertical

frequency of 49 to 51Hz, 59 to 61 Hz.

• When ON is selected, moving pictures are displayed more

smoothly.

• This function is unavailable for a signal from the HDMI (of

480i@60 or 576i@50 or 1080i@50/60) port.

(continued on next page)

INPUT menu

Item

Description

The resolution for the COMPUTER IN1 and COMPUTER IN2 input

signals can be set on this projector.

(1) In the INPUT menu select the RESOLUTION using the ▲/▼

buttons and press the ► button.

The RESOLUTION menu will be

displayed.

(2) In the RESOLUTION menu select the

resolution you wish to display using

the ▲/▼ buttons.

Selecting AUTO will set a resolution

appropriate to the input signal.

(3) Pressing the ► or ENTER button when

selecting a STANDARD resolution will

automatically adjust the horizontal and

STANDARD

vertical positions, clock phase and

horizontal size.

↓

The INPUT_INFORMATION dialog will be

displayed.

(4) To set a custom resolution use the ▲/▼ buttons to select

the CUSTOM and the RESOLUTION_CUSTOM box will be

RESOLUTION

displayed.

CUSTOM

Set the horizontal (HORZ) and

↓

vertical (VERT) resolutions using

the ▲/▼/◄/► buttons.

This function may not support all

resolutions.

(5) Move the cursor to OK on screen and press the ► or ENTER

button. The message "ARE YOU SURE YOU WISH TO

CHANGE RESOLUTION?" appears. To save the setting, press

the ► button.

The horizontal and vertical positions, clock phase and horizontal

size will be automatically adjusted.

The INPUT_INFORMATION dialog

will be displayed.

(6) To revert back to the previous resolution without saving changes,

move the cursor to CANCEL on screen and press the ◄ or

ENTER button.

The screen will then return to the RESOLUTION menu displaying

the previous resolution.

• For some pictures, this function may not work well.

SETUP menu

From the SETUP menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item

Description

Using the ◄/► cursor buttons adjusts the magniﬁcation ratio.

Small Large

• The on-screen menu might be displayed outside of the image

display area depending on the adjustment value of the ASPECT,

D-ZOOM

D-ZOOM,

of ASPECT, D-ZOOM,

the symptom.

KEYSTONE and

KEYSTONE. Changing the values

KEYSTONE and KEYSTONE may ﬁx

Using the ◄/►/▲/▼ cursor buttons adjusts the picture position.

• The D-SHIFT adjustment values are not valid when the D-ZOOM

is set to 256 (full screen). (CP-AX2505, CP-AX3005, CP-AX3505)

• The D-SHIFT adjustment values are not valid when the D-ZOOM

is set to 320 (full screen). (CP-AW2505, CP-AW3005)

D-SHIFT

Using the ▲/▼ cursor buttons selects the vertical picture position.

TOP

MID BOTTOM

ó ó

The PICTURE POSITION is not changed if any of the following

cases apply.

• The ASPECT is set to 4:3.

PICTURE POSITION • The input signal has an aspect ratio of 4:3 or vertically larger than

(CP-AX2505,

CP-AX3005,

CP-AX3505)

4:3, while the ASPECT is set to NORMAL.

• Vertical size of the displayed image is full on the effective display

area, while the ASPECT is set to NATIVE.

• One of the following messages is displayed on the screen:

"NO INPUT IS DETECTED"

"SYNC IS OUT OF RANGE"

"INVALID SCAN FREQ."

• The BLANK or TEMPLATE function is selected.

(continued on next page)

SETUP menu

Item

Description

Using the ▲/▼ cursor buttons selects the horizontal picture

position.

LEFT

MID RIGHT

ó ó

The PICT. POSIT. H is not changed if any of the following cases

apply.

• The ASPECT is set to 16:9 or 16:10.

PICT. POSIT. H

(CP-AW2505,

CP-AW3005)

• The input signal has an aspect ratio of 16:9, 16:10 or verticallly

smaller than 16:10, while ASPECT is set to NORMAL.

• Horizontal size of the displayed image is full on the effective

display area, while the ASPECT is set to NATIVE.

• One of the following messages is displayed on the screen:

"NO INPUT IS DETECTED"

"SYNC IS OUT OF RANGE"

"INVALID SCAN FREQ."

• The BLANK or TEMPLATE function is selected.

Using the ◄/► buttons corrects the vertical keystone distortion.

Shrink the bottom of the image

Shrink the top of the image

• The adjustable range of this function will vary among inputs. For

some input, this function may not work well.

KEYSTONE

• This function will be unavailable when the PERFECT FIT ( 49) is



adjusted.

Using the ◄/► buttons corrects the horizontal keystone distortion.

Shrink the right of the image

Shrink the left of the image

• The adjustable range of this function will vary among inputs. For

some input, this function may not work well.

• This function will be unavailable when the PERFECT FIT ( 49) is



adjusted.

(continued on next page)

SETUP menu

Item

Description

This item allows you to adjust the shape of the projected image in

each of the corners and sides.

(1) Choose a corner or side to adjust

using the ▲/▼/◄/► buttons and press

the ENTER or INPUT button.

(2) Adjust the distortion as below. Use

the ▲/▼/◄/► buttons to adjust the

position of the corner. Use the ▲/▼

buttons to adjust the distortion of the

top or bottom side, after deﬁning the

adjusting position with the ◄/► buttons.

Use the ◄/► buttons to adjust the distortion of the left or right side,

after deﬁning the adjusting position with the ▲/▼ buttons.

(3) To adjust another corner or side, follow the same procedure

from (1) above. To reset the adjustment of all the corners and sides,

select RESET with the ▲/▼/◄/► buttons and press the ENTER or

INPUT button.

(4) This projector is equipped with a memory feature for PERFECT

FIT adjustment. Up to 3 sets of adjustments can be stored.

• SAVE:

PERFECT FIT

To store the current PERFECT FIT adjustment, select one of the

SAVE icons

numbered 1 to 3 (number of the memory) with the

◄ /▲/▼ buttons and press the ENTER or INPUT button.

Remember that the current data being stored of a memory will be

lost by saving new data into the memory.

• LOAD:

To recall stored adjustments, select one of the LOAD icons

numbered 1 to 3 (number of the memory) with the ◄ /▲/▼ buttons

and press the ENTER or INPUT button.

Remember that the current adjusted condition will be lost by

loading data. If you want to keep the current adjustment, please

save it before performing a LOAD function.

- The LOAD functions whose linked memory has no data are

skipped.

- There may be some noise and the screen may ﬂicker for a

moment when loading data. This is not malfunction.

(continued on next page)

SETUP menu

Item

Description

• While the distortion is adjusted with the PERFECT FIT function,

keystone adjustment feature is unavailable. To correct the keystone

distortion, reset the adjustment of all the corners and sides.

• The adjustable range of this correction will vary among inputs. For

some input, this function may not work well.

• One adjustment position common to the top and bottom sides can

be set. Also, another adjustment position common to the left and

right sides can be set.

PERFECT FIT

(continued)

• The distortion of the top and bottom sides can be adjusted only in

the same direction, pincushion or barrel. The adjustment for the left

and right sides is carried out in the same manner.

Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

OFF

AUTO

ECO

MODE

• When ON is selected, the projector will always be set to ECO-2

at start-up regardless of the ECO MODE ( 50) setting. An OSD

message “AUTO ECO MODE” will be displayed for tens of seconds

when the projector starts with this function activated.



Using the ▲/▼ buttons switches the ECO MODE.

OFF

ECO-1

ECO-2

INTELLIGENT ECO

SAVER

• When the ECO-1/2 is selected, acoustic noise and screen

brightness are reduced.

• When INTELLIGENT ECO is selected, the brightness of the

lamp changes according to the level of the input signal. The lamp

becomes brighter when the input signal level is high and darker

when the level is low. If dark images are projected continuously, the

brightness of the lamp may increase to maintain its performance.

• When SAVER is selected, you can select the time within 1 to 30

min. for SAVER MODE using the ► button. If the image signal level

doesn’t change more than the period set, the lamp brightness is

reduced and electric power consumption decreased. If the image

signal level changes or any buttons are operated, the lamp will

brighten again. If dark images are projected continuously, the

brightness of the lamp may increase to maintain its performance.

LAMP &

FILTER

ECO

MODE

• When AUTO ECO MODE ( above) is set to ON, the projector will



always be set to ECO-2 at start-up regardless this setting.

• When the ambient temperature is around 35 to 40°C, the

brightness of lamp is reduced automatically.

(continued on next page)

SETUP menu

Item

Description

The lamp time is the usage time of the lamp, counted after the last

resetting. It is shown in the OPTION menu.

Pressing the RESET button on the remote control or the ► button

of the projector displays a dialog.

To reset the lamp time, select the OK using the ► button.

LAMP

CANCEL OK

TIME

• Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

• For the lamp replacement, see the section "Replacing the lamp"

(

98).



• The IMAGE OPTIMIZER function does not work properly unless

LAMP TIME is initialized when replacing a lamp.

The ﬁlter time is the usage time of the air ﬁlter, counted after the last

resetting. It is shown in the OPTION menu.

Pressing the RESET button on the remote control or the ► button

of the projector displays a dialog.

To reset the ﬁlter time, select the OK using the ► button.

FILTER

TIME

CANCEL OK

LAMP &

FILTER

• Please reset the ﬁlter time only when you have cleaned or

replaced the air ﬁlter, for a suitable indication about the air ﬁlter.

• For the air ﬁlter cleaning, see the section “Cleaning and replacing

the air ﬁlter” ( 100).



Use the ▲/▼ button to set the timer for notifying by the message

when to replace the ﬁlter unit

100h

• • •

ó ó

5000h

OFF

After choosing an item except OFF, the message “REMINDER ***

HRS PASSED ....” will appear after the timer reaches the interval

time set by this feature ( 106).



When the OFF is chosen, the message will not appear. Utilize this

feature to keep the air ﬁlter clean, setting the suitable time according

to your environment of this projector.

FILTER

MESSAGE

• Please take care of the ﬁlter unit periodically, even if there is

no message. If the air ﬁlter becomes to be blocked by dust or

other matter, the internal temperature will rise, which could cause

malfunction, or reduce the lifetime of the projector.

• Please be careful with the operating environment of the projector

and the condition of the ﬁlter unit.

When this function is enabled, automatic image correction

is performed to maintain visibility in accordance with lamp

deterioration.

• This function may not work properly when HDCR/

ACCENTUALIZER is set to other than 0.

IMAGE

OPTIMIZER

• This function does not work properly unless LAMP TIME is

initialized when replacing a lamp.

(continued on next page)

SETUP menu

Item

Description

Pressing the ►button displays the dialog for changing the

INSTALLATION setting.

INSTALLATION

Use the ▲/▼ buttons to select the desired setting on the

INSTALLATION dialog.

Using ▲/▼ buttons switches the standby mode setting between

NORMAL and SAVING.

NORMAL

SAVING

When SAVING is selected, the power consumption in the standby

mode is lowered with some functional restriction as below:

• When SAVING is selected, the RS-232C communication control

except to turn the projector on and the network function are disabled

while the projector is in the standby mode. If the COMMUNICATION

TYPE in the COMMUNICATION menu is set to NETWORK

BRIDGE, all of the RS-232C commands are disabled ( 69).



• When SAVING is selected, STANDBY setting of AUDIO SOURCE

(

53) is invalid, no signal is output from AUDIO OUT port and no



STANDBY MODE

sound from a built-in speaker.

• When SAVING is selected, STANDBY setting of MONITOR OUT

is invalid, and no signal is output from MONITOR OUT port in the

standby mode.

• The USB connection is disabled while the projector is in standby

mode if the STANDBY MODE item in the SETUP menu of the

projector is set to SAVING.

• When SAVING is selected, CLONING load function is invalid while

in STANDBY MODE.

• This function will be unavailable when NETWORK BRIDGE

is selected for COMMUNICATION TYPE.( OPTION menu >



SERVICE > COMMUNICATION)

AUDIO menu

From the AUDIO menu, items shown in the table below

can be performed. Select an item using the ▲/▼ cursor

buttons, and press the ► cursor button or the ENTER

button to execute the item. Then perform it according to

the following table.

Item

Description

Using the ◄/► buttons adjusts the volume.

VOLUME

Low

High

Using the ▲/▼ buttons turns on/off the built-in speaker.

ON OFF

When OFF is selected, the built-in speaker does not work.

SPEAKER

AUDIO SOURCE

MIC VOLUME

While the image signal from the input port chosen in step (1) is

projected, the audio signal from the input port selected in step

(2) is output to both the AUDIO OUT port and built-in speaker of

this projector. However, the built-in speaker does not work when

SPEAKER is set to OFF.

(1) Choose a picture input port using the

▲/▼ buttons.

Choose STANDBY to select the sound

output in the standby mode.

(2) Select an audio input port or the mute

icon using the ◄/► buttons.

The icons indicate the following;

No.1: AUDIO IN1 port

No.2: AUDIO IN2 port

No.3: LAN port

No.4: USB TYPE A port

No.5: USB TYPE B port No.6: HDMI 1 port

No.7: HDMI 2 port : mutes the sound

• Audio input from port nos 4 to 7 can only be selected by each of

the picture input ports.

• Even if the projector is in the standby mode, cooling fans may work

and make noises when the built-in speaker is in operation.

• C.C. (Closed Caption) is automatically activated when is selected

and an input signal containing C.C. is received. This function is

available only when the signal is NTSC for VIDEO or 480i@60 for

COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected

for DISPLAY in the C.C. menu under the SCREEN menu ( 59).



Using the ◄/► buttons adjusts the volume of the microphone

connected to the MIC port.

Low

High

SCREEN menu

From the SCREEN menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item

Description

Using the ▲/▼/◄/► buttons switches the OSD (On Screen

Display) language.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

LANGUAGE

(shown in the LANGUAGE dialog)

Press the ENTER or INPUT button to save the language setting.

Using the ▲/▼/◄/► buttons adjusts the menu position.

MENU POSITION To quit the operation, press the MENU button on the remote control

or keep no operation for about 10 seconds.

Using the ▲/▼ buttons switches the mode for the blank screen.

The blank screen is a screen for the temporarily blanking feature

(

23). It is displayed by pressing the AV MUTE button on the



remote control.

MyScreen

ORIGINAL

BLUE

WHITE

BLACK

BLANK

MyScreen : Screen can be registered by the MyScreen item ( 55).



ORIGINAL : Screen preset as the standard screen.

BLUE, WHITE, BLACK : Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL

screen will change to the plain black screen after several minutes.

Using the ▲/▼ buttons switches the mode for the AUTO BLANK

screen.

BLUE

WHITE

BLACK

AUTO BLANK

• To avoid remaining as an afterimage, displayed image will change

to the designated blank color screen by AUTO BLANK after several

minutes at the following conditions.

- When MyScreen or ORIGINAL is displayed as BLANK screen.

- When start-up screen is displayed.

(continued on next page)

SCREEN menu

Item

Description

Using the ▲/▼ buttons switches the mode for the start-up screen.

The start-up screen is a screen displayed when no signal or an

unsuitable signal is detected.

MyScreen

ORIGINAL

OFF

MyScreen : Screen can be registered by the MyScreen item ( 55).



ORIGINAL : Screen preset as the standard screen.

START UP

OFF : Plain black screen.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL

screen will change to the BLANK screen ( 54) after several



minutes. If also the BLANK screen is the MyScreen or ORIGINAL,

the plain black screen is instead used.

• When the ON is selected to the MyScreen PASSWORD item in

the SECURITY menu ( 76), the START UP is fixed to MyScreen.



This item allows you to capture an image for use as a MyScreen

image which can be used as the BLANK screen and START UP

screen. Display the image you want to capture before executing the

following procedure.

Selecting this item displays a dialog

titled “MyScreen”. It will ask you if

you start capturing an image from the

current screen.

Please wait for the target image to be displayed, and press the

ENTER or INPUT button to start registration.

To restore the screen and return to the previous dialog, press the

RESET button on the remote control.

MyScreen

Registration may take several minutes.

When the registration is completed, the registered screen and the

following message is displayed for several seconds:

“MyScreen registration is ﬁnished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

• This function cannot be selected when the ON is selected to the

MyScreen Lock item ( 56).



• This function cannot be selected when the ON is selected to the

MyScreen PASSWORD item in SECURITY menu ( 76).



•

This function is unavailable for a signal from the LAN, USB TYPE A,

USB TYPE B or HDMI 1/2 port.

(continued on next page)

SCREEN menu

Item

Description

Using the ▲/▼ buttons turns on/off the MyScreen lock function.

OFF

When the ON is selected, the item MyScreen is locked. Use this

function for protecting the current MyScreen.

MyScreen Lock

• This function cannot be selected when the ON is selected to the

MyScreen PASSWORD item in SECURITY menu ( 76).



Using the ▲/▼ buttons turns on/off the message function.

OFF

When the ON is selected, the following message function works.

“AUTO IN PROGRESS” while automatically adjusting

“NO INPUT IS DETECTED”

“SYNC IS OUT OF RANGE”

“INVALID SCAN FREQ.”

“NOT AVAILABLE”

“Searching….” while searching for the input

“Detecting….” while an input signal is detected

“AUTO ECO MODE” while starting up with AUTO ECO MODE

The indication of the input signal displayed by changing

The indication of the aspect ratio displayed by changing

The indication of the PICTURE MODE displayed by changing

The indication of the ACTIVE IRIS displayed by changing

The indication of the MY MEMORY displayed by changing

The indication of “FREEZE” and “II” while freezing the screen by

pressing the FREEZE button.

MESSAGE

The indication of the TEMPLATE displayed by changing.

The indication of the ECO MODE displayed by changing.

The indication of "+++ FOCUS +++" displayed by changing

The D-ZOOM dialog displayed by changing

• When the OFF is selected, please remember if the picture is

frozen. Do not mistake freezing for a malfunction ( 30).



(continued on next page)

SCREEN menu

Item

Description

Each input port for this projector can have a name applied to it.

(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE

NAME and press the ► or ENTER button.

The SOURCE NAME menu will be displayed.

(2) Use the ▲/▼ buttons on the SOURCE

NAME menu to select the port to be

named and press the ► button. The

SOURCE NAME dialog will be displayed.

Right side of the menu is blank until a

name is speciﬁed.

(3) Select an icon you would like to assign to

the port in the SOURCE NAME dialog.

The name assigned to the port will also be

automatically switched according to your

icon selection. Press the ENTER or INPUT

button to determine your icon selection.

SOURCE NAME

(4) Select a number you would like to assign

to the port along with the icon. You can

select the number either from blank

(no number assigned), 1, 2, 3, or 4. Then

press the ENTER or INPUT button.

(5) If you would like to modify the name assigned

to the port, select CUSTOM NAME and

press the ENTER or INPUT button.

(continued on next page)

SCREEN menu

Item

Description

(6) The current name will be displayed on

the ﬁrst line. Use the ▲/▼/◄/► buttons

and the ENTER or INPUT button to

select and enter characters. To erase 1

character at one time, press the RESET

button or press the ◄ and INPUT button

at the same time. Also if you move the

cursor to DELETE or ALL CLEAR on

screen and press the ENTER or INPUT

button, 1 character or all characters will

be erased. The name can be a maximum

of 16 characters.

SOURCE NAME

(Continued)

(7) To change an already inserted character,

press the ▲ button to move the cursor to

the ﬁrst line, and use the ◄/► buttons to

move the cursor on the character to be

changed.

After pressing the ENTER or INPUT button, the character is

selected. Then, follow the same procedure as described at the

item (6) above.

(8) To ﬁnish entering text, move the cursor to the OK on screen and

press the ►, ENTER or INPUT button. To revert to the previous

name without saving changes, move the cursor to the CANCEL

on screen and press the ◄, ENTER or INPUT button.

Using the ▲/▼ cursor buttons switches the mode for the template

screen.

Press the ► cursor (or the ENTER) button to display the selected

template, and press the ◄ cursor button to close the displayed

screen.

TEST PATTERN

DOT-LINE1

DOT-LINE2

DOT-LINE3



TEMPLATE

HAS-WM05

DOT-LINE4



HAS-WM03

MAP2

MAP1

CIRCLE2

CIRCLE1

You can turn a map upside down and scroll it horizontally when

MAP1 or MAP2 is selected. To invert or scroll the map, display

the guidance by pressing the RESET button on the remote three

seconds or more when MAP1 or MAP2 appears.

(continued on next page)

SCREEN menu

Item

Description

The C.C. is the function that displays a

transcript or dialog of the audio portion of

a video, ﬁles or other presentation or other

relevant sounds. It is required to have NTSC

format video or 480i@60 format component

video source supporting C.C. feature to

utilize this function.

It may not work properly, depending on equipment or signal source.

In this case, please turn off the Closed Caption.

DISPLAY

Select Closed Caption DISPLAY setting from following options using

▲/▼ buttons.

AUTO

ON OFF

ó ó

AUTO : Closed Caption automatically appears when the input

signal (C.C. compatible) from the port with the mute icon

set at AUDIO SOURCE is selected.

ON : Closed Caption is on.

OFF : Closed Caption is off.

• The caption is not displayed when the OSD menu is active.

• The Closed Caption is the function to display the dialogue,

narration, and / or sound effects of a television program or other

video sources. The Closed Caption availability is depending upon

broadcaster and/or content.

C.C.

(Closed Caption)

MODE

Select Closed Caption MODE setting from following options using

▲/▼ buttons.

CAPTIONS

TEXT

CAPTIONS : Display Closed Caption.

TEXT : Display Text data, which is for additional information such

as news reports or a TV program guide. The information

covers the entire screen. Not all of the C.C. program has

Text information.

CHANNEL

Select Closed Caption CHANNEL from following options using ▲/▼

buttons.

ó ó ó

1: Channel 1, primary channel / language

2: Channel 2

3: Channel 3

4: Channel 4

The channel data may vary, depending on the content. Some

channel might be used for secondary language or empty.

OPTION menu

From the OPTION menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to execute

the item. Then perform it according to the following

table.

Item

Description

Using the ▲/▼ buttons turns on/off the automatic signal search

function.

OFF

When the ON is selected, detecting no signal automatically cycles

through input ports in the following order. The search is started from

AUTO SEARCH the current port. Then when an input is found, the projector will stop

searching and display the image.

COMPUTER IN1 COMPUTER IN2 LAN USB TYPE A

ð ð

VIDEO HDMI 2 HDMI 1 USB TYPE B



• It may take several seconds to project the images from the

USB TYPE B port.

Using the ▲/▼ buttons turns on/off the DIRECT POWER ON

function.

OFF

When set to the ON, the lamp in projector will be automatically turned

on without the usual procedure ( 20), only when the projector is

supplied with the power after the power was cut while the lamp was on.

• This function does not work as long as the power has been

supplied to the projector while the lamp is off.



DIRECT POWER

•

After turning the lamp on by the DIRECT POWER ON function,

if neither input nor operation is detected for about 30 minutes, the

projector is turned off, even though the AUTO POWER OFF function

(

61) is disabled.



(continued on next page)

OPTION menu

Item

Description

Using the ▲/▼ buttons adjusts the time to count down to

automatically turn the projector off.

Long (max. 99 minutes)

Short (min. 0 minute = DISABLE)

When the time is set to 0, the projector is not turned off automatically.

When the time is set to 1 to 99, and when the passed time with no-

signal or an unsuitable signal reaches at the set time, the projector

lamp will be turned off.

AUTO POWER

OFF

If one of the projector's buttons or the remote control buttons

is pressed or one of the commands (except get commands) is

transmitted to the CONTROL port during the corresponding time,

projector will not be turned off.

Please refer to the section “Turning off the power” ( 22).



(continued on next page)

OPTION menu

Item

Description

This item is to assign one of the following functions to MY BUTTON

1/2 on the remote control ( 6).



(1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY

BUTTON - (1/2) and press the ► or ENTER button to display the

MY BUTTON setup dialog.

(2) Then using the ▲/▼/◄/► buttons sets one of the following

functions to the chosen button. Press the ENTER or INPUT

button to save the setting.

• COMPUTER IN1: Selects the input from COMPUTER IN1 port.

• COMPUTER IN2: Selects the input from COMPUTER IN2 port.

• LAN: Selects input from LAN port.

• USB TYPE A: Selects input from USB TYPE A port.

• USB TYPE B: Selects input from USB TYPE B port.

• HDMI1: Selects input from HDMI 1 port.

• HDMI2: Selects input from HDMI 2 port.

• VIDEO: Selects the input from VIDEO IN port.

• SLIDESHOW: Selects the input from USB TYPE A port, and starts

a Slideshow.

• MY IMAGE: Displays the MY IMAGE menu.

• MESSENGER: Turns the messenger text displayed on the screen on/off

MY BUTTON

(

Messenger Function in the User's Manual - Network Guide).



When there is no transferred text data to display, the message ”NO

MESSENGER DATA" appears.

• INFORMATION: Displays SYSTEM_INFORMATION,

INPUT_INFORMATION ( 73), WIRELESS INFORMATION,



WIRED INFORMATION or nothing.

• MY MEMORY: Loads one of adjustment data stored ( 39).



When more than one data are saved, the adjustment

changes every time the MY BUTTON is pressed.

When no data is saved in memory, the

dialog "No saved data" appears.

When the current adjustment is not

saved to memory, the dialog as shown in

the right appears.

If you want to keep the current adjustment, please press

the ► button to exit. Otherwise loading a data will overwrite the

current adjusted condition.

(continued on next page)

OPTION menu

Item

Description

• ACTIVE IRIS: Changes the active iris mode.

• PICTURE MODE: Changes the PICTURE MODE ( 34).



•

FILTER RESET: Displays the ﬁlter time reset conﬁrmation dialogue

( 51).



MY BUTTON

(Continued)

• RESOLUTION: Turns on/off the RESOLUTION dialog ( 46).



• MIC VOLUME: Turns on/off the MIC VOLUME dialog ( 53).



• ECO MODE: Changes the ECO MODE ( 50).

• SAVER MODE: Turns on/off the SAVER MODE ( 50).



■ How to setup the item

1. Use the ▲/▼/◄/► cursor buttons to select or adjust.

2 Select OK to ﬁnish the settings.

NOTE

• Please refer to the actual on-screen display(OSD)

for appropriate operation.

Item

Description

Set the DATE(Year/Month/Date) and Time(24-

hour scale).

DATE AND TIME

SPECIFIC DATE Set speciﬁc date from 1 to 10.

The TIME and EVENT for Program 1 to 16

can be editted.

PROGRAM EDIT

■ How to activate(DATE AND TIME / SPECIFIC DATE

)

SCHEDULE

Place a check mark in the box.

Date and ﬁrst setup

info could be seen

with the check mark.

Check mark

in the box

1/2 page (Set the DATE(Year/Month/Date) and Time(24-hour scale).)

(continued on next page)

OPTION menu

Item

Description

Date and ﬁrst setup

Check mark

in the box

info could be seen

with the check mark.

2/2 page (Set speciﬁc date from 1 to 10.)

SCHEDULE

(Continued)

Press the ▼ cursor button to move from 1/2 page to 2/2 page with

the state of selecting "SATURDAY".

■ PROGRAM EDIT

The TIME and EVENT for Program 1 to 16 can be editted.

• RETURN

Select this to go back

to the top menu of the

SCHEDULE.

• SELECT

Select from PROGRAM-01

to 16 to edit.

Each PROGRAM can be

setup up to 20 settings

• COPY TO

The selected program (with the settings of TIME and EVENT)

can be copied to other program.

• APPLY

Select this to apply and save all adjustments and settings.

(continued on next page)

OPTION menu

Item

Description

■ How to edit the selected PROGRAM

1. Select from 1 to 20 events.

Use the ▲/▼ cursor buttons to select.

Press ► cursor button to set the TIME and EVENT.

2. Use the ◄/► cursor

buttons to select.

3. Use the ◄/► cursor

buttons to adjust.

EVENT can be selected as listed below.

◦ POWER − ON, STANDBY

◦ INPUT SOURCE − "input source"channel

◦ MY IMAGE − IMAGE-1 to 4, IMAGE OFF

◦ MESSENGER − TEXT-1 to 12, TEXT OFF

SCHEDULE

(Continued)

◦

ECO MODE − OFF, ECO-1, ECO-2, INTELLIGENT ECO,

SAVER

◦ BLANK − ON, OFF

◦ SLIDESHOW - START, STOP

4. Press ► cursor button to finish the settings.

5. Select APPLY to save the settings.

NOTE

• Please refer to the actual on-screen display(OSD)

for appropriate operation.

(continued on next page)

OPTION menu

Item

Description

Selecting this item displays the SERVICE

menu.

Select an item using the ▲/▼ buttons, and

press the ► button or the ENTER button

on the remote control to execute the item.

ALTITUDE

Using the ▲/▼ buttons switches the rotation speed of the cooling

fans. If the projector is used at an altitude of about 1600 m or higher,

select HIGH. Otherwise, select NORMAL. Note that the projector is

noisier when the HIGH is selected.

HIGH

NORMAL

AUTO ADJUST

Using the ▲/▼ buttons to select one of the mode. When the

DISABLE is selected, the automatic adjustment feature is disabled.

SERVICE

FINE

FAST DISABLE

ó ó

FINE: Finer tuning including H.SIZE adjustment.

FAST: Faster tuning, setting H.SIZE to prearranged data for the

input signal.

• Depending on conditions, such as input image, signal cable to

the projector, environment around the projector, etc., the automatic

adjustment may not work correctly. In such a case, please

choose DISABLE to disable the automatic adjustment, and make

adjustment manually.

GHOST

Adjust the settings using the ▲/▼ buttons to eliminate ghosting.

(continued on next page)

OPTION menu

Item

Description

KEY LOCK

(1) Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE

CONTROL.

(2) Use the ◄/► buttons to turn the key lock function on/off.

When ON is selected, all buttons on the projector or remote control

except the STANDBY/ON button are locked.

• Please use this function to prevent tampering or accidental

operation.

SERVICE

• It is not possible to set both CONTROL PANEL and REMOTE

CONTROL to ON.

(continued)

REMOTE RECEIV.

(1) Select a remote sensor using the ▲/▼ button.

FRONT

TOP

(2) Switch it using the ◄/► button.

ON OFF

• When one sensor is turned off, the other cannot be turned off too.

(continued on next page)

OPTION menu

Item

Description

REMOTE FREQ.

(1) Use the ▲/▼ button to change the projector's remote sensor

frequency setting ( 18).



1:NORMAL

2:HIGH

(2) Use the ◄/► button to change the

projector's remote sensor on or off.

OFF

If the remote control does not function correctly, disable either of

them.

It's not possible to disable both options at the same time.

Selecting this item displays COMMUNICATION

menu.

In this menu, you can conﬁgure the serial

communication settings of the projector using the

CONTROL port.

SERVICE

(continued)

• Select an item using the cursor buttons ▲/▼.

COMMUNICATION

Then pressing the ► button opens the submenu

for the setting item you selected. Or, pressing

the ◄ button instead of the ► button makes the

menu back to the previous one without changing

the setup. Each submenu can be operated as

described above.

• When COMMUNICATION TYPE (69) is set to

OFF, the other items in COMMUNICATION menu

are invalid.

• For the function of serial communication, refer to

the User's Manual - Network Guide.

(continued on next page)

OPTION menu

Item

Description

COMMUNICATION TYPE

Select the communication type for transmission via

the CONTROL port.

NETWORK BRIDGE: Select this type, if it is required

to control an external device as a network terminal,

via this projector from the computer.

The CONTROL port doesn't accept RS-232C

commands ( Network Bridge Function in the



User’s Manual - Network Guide

)

OFF: Select this mode to receive RS-232C

commands using the CONTROL port.

•

OFF is selected as the default setting.

• When you select the NETWORK BRIDGE, check

the item, TRANSMISSTION METHOD ( below).



SERIAL SETTINGS

Select the serial communication condition for the

CONTROL port.

BAUD RATE

4800bps

9600bps

19200bps

38400bps

SERVICE

(continued)

COMMUNICATION

(continued)

PARITY

NONE

ODD EVEN

ó ó

•

The BAUD RATE is ﬁxed to 19200bps and PARITY

is ﬁxed NONE when the COMMUNICATION TYPE

is set to OFF above).

(



TRANSMISSION METHOD

Select the transmission method for communication by

the NETWORK BRIDGE from the CONTROL port.

HALF-DUPLEX

FULL-DUPLEX

HALF-DUPLEX: This method lets the projector

make two way communication, but only one

direction, either transmitting or receiving data, is

allowed at a time.

FULL-DUPLEX: This method lets the projector

make two way communication, transmitting and

receiving data at the same time.

• HALF-DUPLEX is selected as the default setting.

• If you select HALF-DUPLEX, check the setting of

the item RESPONSE LIMIT TIME ( 70).



(continued on next page)

OPTION menu

Item

Description

RESPONSE LIMIT TIME

Select the time period to wait for receiving

response data from other device communicating by

the NETWORK BRIDGE and the HALF-DUPLEX

through the CONTROL port.

OFF

1s 3s

ó ó ó

OFF: Select this mode if it is not required to check

the responses from the device that the projector

sends data to. In this mode, the projector can

send out data from the computer continuously.

COMMUNICATION

(continued)

1s /2s /3s: Select the time period to keep the

projector waiting for response from the device

that the projector sends data to. While waiting the

response, the projector does not send out any

data from the CONTROL port.

SERVICE

(continued)

• This menu is available only when the NETWORK

BRIDGE is selected for the COMMUNICATION

TYPE and the HALF-DUPLEX is selected for the

TRANSMISSION METHOD ( 69).



• OFF is selected as the default setting.

The setttings of the projector can be coppied via USB

memory.

SAVE:Saves each settings of the projector to USB

memory.

LOAD:Loads each settings of the projector from

USB memory. Message will be displayed

after loading, and power will turn off after ﬁve

min. or by pressing ► button. (A message is

displayed for a few seconds if loading fails.)

CLONING

After saving / loading, you can remove the USB

storage device.

(continued on next page)

OPTION menu

Item

Description

The following items are exempted.

SETUP: LAMP TIME, FILTER TIME

OPTION: SERVICE(GHOST)

NETWORK: WIRELESS AND WIRED SETUP

(IP ADDRESS, SUBNET MASK,

DEFAULT GATEWAY, DATE AND

TIME), MY IMAGE, PRESENTATION,

AMX D.D.

SECURITY: MY TEXT DISPLAY

• Operation is not available if SECURITY_

CLONNING LOCK is turned ON.

• The Screen_MyScreen can only be loaded.

CLONING load function on STANDBY MODE

• While the projector is in STANDBY MODE, push

the INPUT button of control panel together with ►

button, and then press ▲ button to start operating

the CLONING load function.

• During loading process, the three indicators of

control panel (POWER (orange), TEMP, LAMP)

will remain on.

SERVICE

CLONING

• After the loading process, the three indicators

(POWER (orange), TEMP, LAMP) will turn off.

Then, you can remove the USB storage device.

• If the loading fails, the three indicators (POWER

(orange), TEMP, LAMP) will blink at the same

time.

(continued)

• CLONING is invalid with the following conditions.

- CLONING LOCK is turned ON.

With this condition, the three indicators (POWER

(orange), TEMP, LAMP) will blink at approximately

three seconds intervals.

- If the STANDBY MODE is set to SAVING.

- If there is no USB memory inserted into USB

TYPE A port.

- If PIN LOCK is not being released.

- If a system error occurs.

• Please operate one of the following after loading.

- Press INPUT button and

◄

button of the control

panel at the same time.

- Wait at least ﬁve min. after loading.

- Restart the projector after re-plugging the AC

cable.

(continued on next page)

OPTION menu

Item

Description

Load MyScreen data

• Please save the image data as "pj_logo.bmp" or

"pj_logo.gif" into USB memory.

• Please note that the only compatible formats are

as follows.

-File format

Windows BMP bit/pixel: 4/8/16/24/32bit

Compression format :

Without compression/RLE/GIF

-Image size: more than 36x36, less than 1280x800

• If two kinds of ﬁle format are saved, "pj_logo.

bmp" will be registered into MyScreen data.

• If MyScreen LOCK or MyScreen PASSWORD

is turned ON, the data of MyScreen cannot be

loaded.

SERVICE

(continued)

CLONING

(continued)

Setting the data

• Operating the SAVE function under CLONING

will name the ﬁle as "pj_data.bin" into the USB

memory. Please do not attempt to change the ﬁle

name or the folder structure.

• If a ﬁle with the same name already exists, it will

be overwritten by operating the SAVE function.

Loading function

• Please note that saved data from other model

cannot be loaded.

•

Please note that, if any of the following functions:

MyScreen PASSWORD, PIN LOCK, MY TEXT

PASSWORD under SECURITY menu or

MyScreen Lock under SCREEN menu is ON, the

respective saved data cannot be loaded.

(continued on next page)

OPTION menu

Item

Description

Loading function (continued)

•

Please note that the saved data of START UP

and MyScreen Lock under SCREEN menu cannot

be loaded if MyScreen PASSWORD under

SECURITY menu is ON.

CLONING

(continued)

•

Please note that the saved data of MY TEXT

WRITING cannot be loaded if MY TEXT

PASSWORD under SECURITY menu is ON.

INFORMATION

Selecting this item displays a dialog titled “INPUT_INFORMATION”.

It shows the information about the current input.

SERVICE

(continued)

• The “FRAME LOCK” message on the dialog means the frame lock

function is working.

• This item can't be selected for no signal and sync out.

• When the MY TEXT DISPLAY is set to ON, the MY TEXT is

displayed together with the input information in the INPUT_

INFORMATION box ( 79).



FACTORY RESET

Selecting OK using the ► button performs this function. By this

function, all the items in all of menus will collectively return to the

initial setting. Note that the items STANDBY MODE, AUTO BLANK,

LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE,

NETWORK and SECURITY settings are not reset.

CANCEL OK

Be sure to set ALTITUDE after resetting all the settings ( 66).



NETWORK menu

See the Network Guide for details of NETWORK operation.

Remember that incorrect network settings on this projector may cause trouble on

the network. Be sure to consult with your network administrator before connecting

to an existing access point on your network.

SECURITY menu

This projector is equipped with security functions.

From the SECURITY menu, items shown in the table

below can be performed.

To use SECURITY menu: User registration is required

before using the security functions.

Enter to the SECURITY menu

1. Press the ► button. The ENTER PASSWORD box will be displayed.

2. Use the ▲/▼/◄/► buttons to enter the registered password. The

factory default password is as follows.

CP-AX2505, CP-AX3005, CP-AX3505 : 1036

CP-AW2505, CP-AW3005 : 9435

This password can be changed

right side of the ENTER PASSWORD box and press the ► button to

display the SECURITY menu.

. Move the cursor to the

below)

(



• It is strongly recommended the factory default password to be

changed as soon as possible.

• If an incorrect password is input, the ENTER PASSWORD box

will be displayed again. If incorrect password is input 3 times, the

projector will turn off. Afterwards the projector will turn off every time

an incorrect password is input.

3. Items shown in the table below can be performed.

If you have forgotten your password

(1). While the ENTER PASSWORD box is displayed, press and hold

the RESET button on the remote control for about 3 seconds or

press and hold the INPUT button for 3 seconds while pressing the

► button on the projector.

(2). The 10 digit Inquiring Code will be displayed. Contact your dealer

with the 10 digit Inquiring Code. Your password will be sent after

your user registration information is conﬁrmed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will

close. If necessary, repeat the process from (1).

Item

Description

(1) Use the ▲/▼ buttons on the SECURITY menu

to select SECURITY PASSWORD CHANGE

and press the ► button to display the ENTER

NEW PASSWORD box.

(2) Use the ▲/▼/◄/► buttons to enter the new password.

(3) Move the cursor to the right side of the ENTER

NEW PASSWORD box and press the ► button

to display the NEW PASSWORD AGAIN box,

enter the same password again.

(4) Move the cursor to the right side of the NEW

PASSWORD AGAIN box and press the ►

button and the NOTE NEW PASSWORD box

will be displayed for about 30 seconds, please

make note of the password during this time.

SECURITY

PASSWORD

CHANGE

Pressing the ENTER button on the remote control or

►

button on the

projector will close the NOTE NEW PASSWORD box.

• Please do not forget your password.

(continued on next page)

SECURITY menu

Item

Description

The MyScreen PASSWORD function can be used to prohibit access to the

MyScreen function and prevent the currently registered MyScreen image

from being overwritten.

1 Turning on the MyScreen PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

select MyScreen PASSWORD and press the ►

button to display the MyScreen PASSWORD on/

off menu.

1-2 Use the ▲/▼ buttons on the MyScreen

PASSWORD on/off menu to select ON.

The ENTER NEW PASSWORD box (small)

will be displayed.

ENTER NEW PASSWORD

box (small)

1-3 Use the ▲/▼/◄/► buttons to enter the

password. Move the cursor to the right side

of the ENTER NEW PASSWORD box (small)

and press the ► button to display the NEW

PASSWORD AGAIN box, enter the same

PASSWORD again.

1-4 Move the cursor to the right side of the

NEW PASSWORD AGAIN box and press

the ► button to display the NOTE NEW

PASSWORD box for about 30 seconds,

please make note of the password during

this time.

Pressing the ENTER button on the remote control or ► button on the

MyScreen

PASSWORD

projector will return to MyScreen PASSWORD on/off menu.

When a password is set for MyScreen:

The MyScreen registration function (and menu) will be unavailable.

The MyScreen Lock menu will be unavailable.

The START UP setting will be locked on MyScreen (and the menu will be

•

unavailable).

Turning the MyScreen PASSWORD off will allow normal operation of these

functions.

Please do not forget your MyScreen PASSWORD.

•

2 Turning off the MyScreen PASSWORD

2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

menu.

2-2 Select OFF to display the ENTER

PASSWORD box (large). Enter the registered

password and the screen will return to the

MyScreen PASSWORD on/off menu.

ENTER PASSWORD box

(large)

If an incorrect PASSWORD is input, the menu will

close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

menu.

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

Inquiring Code will be displayed inside the box.

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will

be sent after your user registration information is conﬁrmed.

(continued on next page)

SECURITY menu

Item

Description

PIN LOCK is a function which prevents the projector from being used unless

a registered Code is input.

1 Turning on the PIN LOCK

1-1 Use the ▲/▼ buttons on the SECURITY menu

to select PIN LOCK and press the ► button or

the ENTER button to display the PIN LOCK on/off

menu.

1-2 Use the ▲/▼ buttons on the PIN LOCK on/

off menu to select ON and the Enter PIN

Code box will be displayed.

1-3 Input a 4 part PIN code using the ▲/▼/◄/►,

COMPUTER or INPUT button.

The PIN Code again box will appear.

Reenter the same PIN code. This will complete

the PIN code registration.

If there is no key input for about 55 seconds

while the Enter PIN Code box or the PIN Code again box is displayed,

the menu will close. If necessary, repeat the process from 1-1.

•

Afterwards, anytime the projector is restarted after AC power is turned off

the Enter PIN Code box will be displayed. Enter the registered PIN code.

The projector can be used after entering the registered PIN code. If an

incorrect PIN code is input, the Enter PIN code box will be displayed again.

If an incorrect PIN code is input 3 times, the projector will turn off. Afterwards

the projector will turn off every time an incorrect PIN code is input. The

projector will also turn off if there is no key input for about 5 minutes while

the Enter PIN code box is displayed.

PIN LOCK

This function will activate only when the projector is started after AC power

is turned off.

Please do not forget your PIN code.

•

2 Turning off the PIN LOCK

2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu.

2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be

displayed.

Enter the registered PIN code to turn the PIN LOCK function off.

If an incorrect PIN code is input 3 times, the projector will turn off.

3 If you have forgotten your PIN code

3-1 While the Enter PIN code box is displayed, press and hold the RESET

button for 3 seconds or press and hold the INPUT button for 3 seconds

while pressing the ► button on the projector.

The 10 digit Inquiring Code will be displayed.

If there is no key input for about 5 minutes

while the Inquiring Code is displayed, the

•

projector will turn off.

3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will

be sent after your user registration information is conﬁrmed.

(continued on next page)

SECURITY menu

Item

Description

The MY TEXT PASSWORD function can prevent the MY TEXT from being

overwritten. When the password is set for the MY TEXT;

• The MY TEXT DISPLAY menu will be unavailable, which can prohibit

changing the DISPLAY setting.

• The MY TEXT WRITING menu will be unavailable, which can prevent the

MY TEXT from being overwritten.

1 Turning on the MY TEXT PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT PASSWORD and press the

► button to display the MY TEXT PASSWORD

on/off menu.

1-2 Use the ▲/▼ buttons on the MY TEXT

PASSWORD on/off menu to select ON. The

ENTER NEW PASSWORD box (small) will

be displayed.

1-3 Use the ▲/▼/◄/► buttons to enter the

password. Move the cursor to the right side

of the ENTER NEW PASSWORD box (small)

and press the ► button to display the NEW

PASSWORD AGAIN box, and then enter the

same password again.

ENTER NEW PASSWORD

box (small)

1-4 Move the cursor to the right side of the NEW

PASSWORD AGAIN box and press ► button

to display the NOTE NEW PASSWORD box

for about 30 seconds, then please make note

of the password during this time.

MY TEXT

PASSWORD

Pressing the ENTER button on the remote control or ► button on the

projector will return to the MY TEXT PASSWORD on/off menu.

2 Turning off the MY TEXT PASSWORD

2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

menu.

2-2 Select OFF to display the ENTER

PASSWORD box (large). Enter the registered

password and the screen will return to the

MY TEXT PASSWORD on/off menu.

ENTER PASSWORD box

(large)

If an incorrect password is input, the menu will close.

If necessary, repeat the process from 2-1

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

menu.

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

inquiring code will be displayed inside the box.

3-3 Contact your dealer with the 10 digit inquiring code. Your password will

be sent after your user registration information is conﬁrmed.

(continued on next page)

SECURITY menu

Item

Description

(1) Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT DISPLAY and press the ► or

ENTER button to display the MY TEXT DISPLAY

on/off menu.

(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select

on or off.

OFF

MY TEXT

DISPLAY

When it is set ON, the MY TEXT will be displayed

on the START UP screen and the INPUT_

INFORMATION when the INFORMATION on the

SERVICE menu is chosen.

• This function is available only when the MY TEXT

PASSWORD function is set to the OFF.

(1) Use the ▲/▼ buttons on the

SECURITY menu to select the MY

TEXT WRITING and press the ►

button. The MY TEXT WRITING dialog

will be displayed.

(2) The current MY TEXT will be displayed

on the ﬁrst 3 lines. If not yet written, the

lines will be blank.

Use the ▲/▼/◄/► buttons and the

ENTER or INPUT button to select and

enter characters. To erase 1 character

at one time, press the RESET button or

press the ◄ and INPUT button at the

same time. Also if you move the cursor

to DELETE or ALL CLEAR on screen

and press the ENTER or INPUT button,

1 character or all characters will be

MY TEXT

WRITING

erased. The MY TEXT can be input up

to 24 characters on each line.

(3) To change an already inserted

character, press the ▲/▼ button to

move the cursor to one of the ﬁrst 3

lines, and use the ◄/► buttons to

move the cursor on the character to be

changed.

After pressing the ENTER or INPUT button, the character is selected.

Then, follow the same procedure as described at the item (2) above.

(4) To ﬁnish entering text, move the cursor to the OK on screen and press

the ►, ENTER or INPUT button. To revert to the previous MY TEXT

without saving changes, move the cursor to the CANCEL on screen and

press the ◄, ENTER or INPUT button.

The MY TEXT WRITING function is available only when the MY TEXT

PASSWORD function is set to OFF.

•

The CLONING operation under OPTION_SERVICE menu is not available if

ON is selected.

CLONING LOCK

Presentation tools

The projector has the following convenient tools that enable on-screen

presentations easily and quickly:

- PC-LESS Presentation (below)

- Drawing function

Drawing function enables you to draw on the projector’s screen with

USBmouse or tablets connected to the USB TYPE A ports. For details, refer to

the manual for peripheral equipment.

- USB Display (90, 94)

PC-LESS Presentation

The PC-LESS Presentation reads image and audio data from the storage media

inserted into the USB TYPE A port and displays the image in the following modes.

The PC-LESS Presentation can be started by selecting the USB TYPE A port as

the input source.

This feature allows you to make your presentations without using your computer.

- Thumbnail mode (81)

- Full Screen mode (85)

- Slideshow mode (87)

[Supported storage media]

• USB memory (USB memory type, USB hard disk and USB card reader type)

NOTE • USB readers (adapters) that have more than one USB slot may not

work (if the adapter is acknowledged as multiple devices connected).

• USB devices with security software may not work.

• Be careful when inserting or removing a USB device. (13, 83)

[Supported format]

• FAT12, FAT16 and FAT32

NOTE • NTFS is not supported.

PPrreesseennttaattioionnttoooolsls

PC-LESS Presentation (continued)

[Supported ﬁle format and its extension]

• JPEG (.jpeg, .jpg)

• Bitmap (.bmp)

• PNG (.png)

* Progressive is not supported.

* 16bit mode and compressed bitmap is not supported.

* Interlace PNG is not supported.

• GIF (.gif)

• Movie (.avi, .mov)

Supported video format: Motion-JPEG

Supported audio format: WAV (Linear PCM, Stereo 16bit),

IMA-ADPCM

NOTE • Files with a resolution larger than the following are not supported.

CP-AX2505, CP-AX3005, CP-AX3505 : 1024 x 768 (Still)，768 x 576 (Movie)

CP-AW2505, CP-AW3005 : 1280 x 800 (Still)，768 x 576 (Movie)

(* Some computers may not support 1280 x 800.)

• Files with a resolution smaller than 36 x 36 are not supported.

• Files with a resolution smaller than 100 x 100 may not be displayed.

• Movie images with a frame rate higher than 15 fps cannot be displayed.

• Movie images with a bit rate higher than 20 Mbps cannot be displayed.

• Some supported ﬁles may not be displayed.

• Only a frame appears when the content of image data cannot be displayed in

the Thumbnail mode.

• Even with the ﬁle format and audio format combinations described above,

playback of some ﬁles may fail.

Thumbnail mode

The Thumbnail mode displays the images stored in a USB storage device on the

Thumbnail screen. Maximum 20 images are displayed in a screen.

If you wish, you can jump into the Full Screen mode or Slideshow mode, after you

select some images in the Thumbnail mode.

The Thumbnail mode will be started as the primary function of the PC-LESS

Presentation after selecting the USB TYPE A port as the input source.

Selected image

Thumbnail menu

Thumbnail images

Presentation tools

PC-LESS Presentation (continued)

Operating by buttons or keys

You can control the images on the Thumbnail screen with the remote control,

control panel or Web Remote Control. The following functions can be supported

while the Thumbnail is displayed.

Button operation

Functions

Web Remote

Control

The remote

control

Control panel

▲/▼/◄/►

[▲]/[▼]/[◄]/[►] Move cursor

PAGE UP

PAGE DOWN

[PAGE UP]

Switches pages

[PAGE DOWN]

• Displays the selected image

on the Full Screen mode when a

cursor is on a thumbnail image.

• Displays the setup menu

ENTER

INPUT

[ENTER]

(

below) for the selected image



when a cursor is on a thumbnail

image number.

The setup menu for the selected image

Use the ◄/► cursor buttons to switch each setting or use the ► cursor button to execute

the functions as follows.

Item

Functions

RETURN Press the ► cursor button or ENTER to return to the Thumbnail screen.

Switch to ON to set the selected image as the ﬁrst image in the

Slideshow. This setting information will be saved in the “playlist.txt” ﬁle

START

(89).

Switch to ON to set the selected image as the last image in the

Slideshow. This setting information will be saved in the “playlist.txt” ﬁle

(89).

STOP

SKIP

Switch to ON to skip the selected image in the Slideshow. This setting

information will be saved in the “playlist.txt” ﬁle (89).

Press the ► cursor or ENTER button to rotate the selected still image

ROTATE 90 degrees clockwise. This setting information will be saved in the

“playlist.txt” ﬁle (89).

Presentation tools

PC-LESS Presentation (continued)

Operating by the menu on the Thumbnail screen

You can also control the images by using the menu on the Thumbnail screen.

Item

Functions

Moves to an upper folder.

SORT

Allows you to sort ﬁles and folders as following.

Press the ► cursor button or ENTER to return to the Thumbnail

screen.

RETURN

NAME UP

Sorts in ascending order by ﬁle name.

NAME DOWN Sorts in descending order by ﬁle name.

DATE UP

Sorts in ascending order by ﬁle date.

Sorts in descending order.by ﬁle date.

Go to previous / next page.

DATE DOWN

▲/▼

SLIDESHOW

RETURN

Conﬁgures and starts the Slideshow ( 87).



Press the ► cursor button or ENTER to return to the Thumbnail

screen.

PLAY

Press the ► cursor button or ENTER to start the Slideshow.

Sets the beginning number of the Slideshow.

Sets the end number of the Slideshow.

START

STOP

Sets the interval time for displaying still images during the

Slideshow.

INTERVAL

PLAY MODE

INPUT

Selects the Slideshow mode.

Switches the input port.

Displays the menu.

Be sure to use this function before removing USB storage device

from the projector. After that, the projector will not recognize a

USB storage device until you insert it again into the USB TYPE A

input port.

REMOVE USB

Turns the sound on/off for ﬁles that contain audio data.

Presentation tools

PC-LESS Presentation (continued)

NOTE • These operations are not accessible while the projector OSD is displayed.

• The Thumbnail mode is able to display up to 20 ﬁles in one page.

• It is not possible to change the input port by using the INPUT button when the

Thumbnail screen, Slideshow, or Full Screen is displayed.

• The image quality may deteriorate when playing back audio data included in

a movie. If you want to give priority to the image quality, turn off the sound by

setting ♪ to off.

• If one of the AUDIO IN ports is selected or is selected for USB TYPE A in

AUDIO SOURCE of the AUDIO menu (53), ♪ cannot be operated.

• Some error icons will be displayed in the Thumbnail.

This ﬁle seems to be broken or not supported format.

A ﬁle that cannot be displayed on the

thumbnail screen is indicated by a ﬁle

format icon.

Presentation tools

PC-LESS Presentation (continued)

Full Screen Mode

The Full Screen mode shows a full display image. To display in Full Screen mode,

select an image in the Thumbnail screen. Then press the ENTER button on the

remote control, the INPUT button on the control panel or click [ENTER] on the

Web Remote Control.

Full screen display

Operations for still images

The following operations are enabled in the Full Screen mode while a still image

is displayed.

Button operation

Functions

Web Remote

Control

The remote

control

Control panel

▼

►

[▼]

[►]

▼

►

Shows the next ﬁle.

PAGE DOWN

[PAGE DOWN]

▲

◄

[▲]

[◄]

▲

◄

Shows the previous ﬁle.

Displays Thumbnail.

PAGE UP

[PAGE UP]

ENTER

INPUT

[ENTER]

Presentation tools

PC-LESS Presentation (continued)

Operations for movie

A remote control icon and a progress bar are

displayed when one of the cursor buttons, ENTER

button or INPUT button on the remote control, control

panel or Web Remote Control is pressed or clicked while a movie is playing in the

Full Screen mode. The following operations are enabled while the remote control

icon and progress bar are displayed.

Button operation

Functions

Web Remote

Control

The remote

control

Control panel

▲

►

◄

▲

►

◄

[▲]

(Play) /

(Pause) toggle

[►]

(FF) Fast-forward

[◄]

(REW) Fast-rewind

ENTER

INPUT

[ENTER]

(Stop), Displays Thumbnail.

PAGE DOWN

PAGE UP

–

[PAGE DOWN] Shows the next ﬁle.

[PAGE UP] Shows the previous ﬁle.

NOTE • These operations are not accessible while the projector OSD is displayed.

• It is not possible to change the input port by using the INPUT button when the

Thumbnail screen, Slideshow, or Full Screen is displayed.

Presentation tools

PC-LESS Presentation (continued)

Slideshow mode

The Slideshow mode displays images in full screen and switches the images at

intervals set in INTERVAL on the Thumbnail screen menu (82).

You can start this function from the Slideshow menu. To display the Slideshow

menu, select the SLIDESHOW button in the Thumbnail mode and press the

ENTER button on the remote control, INPUT button on the control panel, or click

[ENTER] on the Web Remote Control.

While the Slideshow is displayed, the following button operations are enabled

when still images are displayed, and the same button operations in the Full

Screen mode are enabled when movies are displayed.

Button operation

Functions

Displays thumbnail

Web Remote

Control

The remote

control

Control panel

ENTER

INPUT

[ENTER]

NOTE • These operations are not accessible while the projector OSD is

displayed.

• It is not possible to change the input port by using the INPUT button when the

Thumbnail screen, Slideshow, or Full Screen is displayed.

• When the Slideshow mode is set to ONE TIME and the last ﬁle is a still image,

the last slide of the presentation will remain displayed until the ENTER button

on the remote control or Web Remote Control, or the INPUT button on the

control panel is pressed.

Presentation tools

PC-LESS Presentation (continued)

You can play the Slideshow at your desired conﬁguration.

Conﬁgure the Slideshow items in the Thumbnail.

1) RETURN

2) PLAY

: Returns to the thumbnail mode.

: Play the Slideshow.

3) START

Set the beginning number of the

Slideshow.

4) STOP

5) INTERVAL

: Set the end number of the Slideshow.

: Sets the interval time for displaying still

images during the Slideshow.

It is not recommend to set the interval

time very short something like several

seconds, because it may take more than

several seconds to read and display an

image ﬁle if it is stored in very deep layer

directory or if so many ﬁles are stored in

the same directory.

6) PLAY MODE : Select the Slideshow mode.

ONE TIME : Play the Slideshow one time.

ENDLESS : Play the Slideshow endless.

NOTE • The settings of the Slideshow are saved to the “playlist.txt” ﬁle

that is stored in the storage media. If the ﬁle is not existed, it is generated

automatically.

• The settings for the START, STOP, INTERVAL, and PLAY MODE are saved to

the Playlist.

• If the storage media is under the write protection or the “playlist.txt” is the

read only type ﬁle, it is impossible to change the settings of the Slideshow.

Presentation tools

PC-LESS Presentation (continued)

Playlist

The Playlist is a DOS format text ﬁle, which decides the order of displayed still

image ﬁles in the Thumbnail or Slideshow.

The playlist ﬁle name is “playlist.txt” and it can be edited on a computer.

It is created in the folder that contains the selected image ﬁles when the PC-LESS

Presentation is started or the Slideshow is conﬁgured.

[Example of “playlist.txt” ﬁles]

START setting : STOP setting : INTERVAL setting : PLAY MODE setting :

img001.jpg: : : :

img002.jpg:600: : :

img003.jpg:700:rot1: :

img004.jpg: : :SKIP:

img005.jpg:1000:rot2:SKIP:

The “playlist.txt” ﬁle contains the following information.

Each piece of information requires to be separated by “:”, and “:” at the end of each line.

1st line: START, STOP, INTERVAL and PLAY MODE settings (88).

2nd line and after: ﬁle name, interval time, rotation setting and skip setting.

interval time: It can be set from 0 to 999900 (ms) with an increment of 100 (ms).

rotation setting: “rot1” means a rotation at 90 degrees clockwise; “rot2” and

“rot3” increase another 90 degrees in order.

skip setting: “SKIP” means that the image will not be displayed in the

Slideshow.

NOTE • The maximum length in a line on the "playlist.txt" ﬁle is 255 characters

including linefeed. If any line exceeds the limit, the "playlist.txt" ﬁle becomes invalid.

•

Up to 999 ﬁles can be registered to the Playlist. However, if some folders exist in

the same directory the limit number is decreased by the number of folders.

Any ﬁles over the limit will not be shown in the Slideshow.

•

If the storage device is protected or does not have sufﬁcient space, the “playlist.txt”

ﬁle cannot be created.

• For the Slideshow settings, refer to the section Slideshow mode (87).

Presentation tools

USB Display(Windows computer)

The projector can display images transferred from a computer via an USB cable (10).

Hardware and software requirement for computer

• OS: One of the following.

Windows Vista ^®Home Basic /Home Premium /Business /Ultimate /Enterprise

Windows ^®7 Starter /Home Basic /Home Premium /Professional / Ultimate /

Enterprise

Windows ^®8/8.1 / Windows ^®8/8.1 Pro / Windows ^®8/8.1 Enterprise

• CPU: Pentium 4 (2.8 GHz or higher)

• Graphic card: 16 bit, XGA or higher

• Memory: 512 MB or higher

• Hard disk space: 30 MB or higher

• USB Port

• USB cable : 1 piece

Starting USB Display

When you connect your computer to the USB TYPE B port on the projector

using a USB cable, the projector will be recognized as a CD-ROM drive on your

computer. Then, the software in the projector, “LiveViewerLiteForUSB.exe”, will

run automatically and the application, “LiveViewer Lite for USB”, will be ready on

your computer for the USB Display. The application, “LiveViewer Lite for USB”, will

close automatically when the USB cable is unplugged. However, it may remain

displayed at times.

NOTE • If the software does not start automatically (this is typically because

CD-ROM autorun is disabled on your OS), follow the instructions below.

(1) Click on the [Start] button on the toolbar and select the “Run”

(2) Enter F:\LiveViewerLiteForUSB.exe and then press the [OK]

If your CD-ROM drive is not drive F on your computer, you will

need to replace F with the correct drive letter assigned to your

CD-ROM drive.

• CD-ROM autorun is disabled while the screen saver is running.

• The image transmission from the computer is suspended while the password-

protected screen saver is running. To resume the transmission, exit the screen

saver.

•

If "Waiting for connection." remains displayed while the USB cable is connected,

remove the USB cable and reconnect after a while.

• Check our web site for the latest version of the software and its manual.

(User's Manual (concise))

Follow the instructions that can be obtained at the site for updating.

(continued on next page)

Presentation tools

USB Display(Windows computer) (continued)

This application will appear in the Windows

notiﬁcation area once it starts. You can quit the

application from your computer by selecting “Quit” on

the menu.

NOTE • The “LiveViewer” (refer to the

Network Guide) and this application cannot

be used at the same time. If you connect your

computer to the projector by using a USB cable

while the “LiveViewer” is running, the following message will be displayed.

• Depending on the software installed on your computer, images on your

computer cannot be transferred using “LiveViewer Lite for USB”.

• If any application software having the ﬁrewall function is installed into your

computer, make the ﬁrwall function invalid with following the user's manual.

• Some security software may block image transmission. Please change the

security software setting to allow the use of "LiveViewer Lite for USB".

• When the audio input from USB TYPE B is selected, if the sound level is still

low even after raising the volume level in the projector to the maximum, check

whether your computer outputs audio and raise the volume level accordingly.

• If the computer in use is equipped with HDMI port, the audio setting will be

changed and sound interruption or noise may occur when the HDMI cable is

connected or disconnected during USB Display. Restart USB Display for this

case.

• Image distortion or sound interruption may occur when “LiveViewer” is

connected to LAN (wireless or wired) during USB Display. The above decline in

performance is noticeable especially when multiple computers are connected to

“LiveViewer”.

Presentation tools

USB Display(Windows computer) (continued)

Right-Click menu

The menu shown in the right will be displayed

when you right-click the application icon in the

Windows notiﬁcation area.

Display : The Floating menu is displayed, and the icon disappears from the

Windows notiﬁcation area.

Quit

: The application is closed, and the icon disappears from the Windows

notiﬁcation area.

NOTE • If you wish to restart the application, you need to unplug the USB

cable and plug it again.

Floating menu

If you select “Display” on the Right-Click

menu, the Floating menu shown in the right

will appear on your computer screen.









 Start capture button

The transmission to the projector is started

and the images will be displayed.

 Stop button



The image transmission is stopped.

 Hold button

The image on the projector’s screen is temporally frozen. The last image before

the button is clicked is remained on the screen. You can revise the image data

on your computer without showing it on the projector's screen.

 Option button

The Options window is displayed.

 Minimize button

The Floating menu is closed, and the icon reappears in the Windows notiﬁcation

area.

NOTE • If you click the Start capture button and/or Stop button repeatedly,

images may not be displayed on the screen.

Presentation tools

USB Display(Windows computer) (continued)

Options window

If you select the Option button on the Floating

menu, the Options window is displayed.

Optimize Performance

The “LiveViewer Lite for USB” captures

screenshots in JPEG data and sends them to

the projector. The “LiveViewer Lite for USB” has

two options that have different compression rate

of JPEG data.

Transmission speed

Speed takes priority over Image quality.

It makes JPEG compression rate higher.

The screen on the projector is rewritten quicker because the transferred

data is smaller, but the image quality is worse.

Image quality

Image quality takes priority over Speed.

It makes JPEG compression rate lower.

The screen on the projector is rewritten slower because the transferred

data is larger, but the image quality is better.

Keep PC resolution

If you remove the check mark from the [Keep PC resolution] box, the screen

resolution of your computer will be switched as follows, and the display speed

may be faster.

CP-AX2505, CP-AX3005, CP-AX3505: 1024 x 768 (XGA)

CP-AW2505, CP-AW3005: 1280 x 800 (WXGA)

If your computer does not support the display resolution speciﬁed above, a

smaller resolution that is the largest among the resolutions that are supported by

the computer will be selected.

Sound

Turns the sound on/off. The image quality may deteriorate when you play back

audio data transferred together with the image data. To give priority to the image

quality, turn off the sound by selecting the checkbox.

Display LiveViewer Lite for USB

If you want to display the "LiveViewer Lite for USB" application window on the

screen, please check the box.

About

The version information of the “LiveViewer Lite for USB”.

NOTE • When the resolution is changed, the arrangement of icons on

computer desktop screen may be changed.

• If one of the AUDIO IN ports is selected or is selected for USB TYPE B

in AUDIO SOURCE of the AUDIO menu (53), audio sound operation in the

Options window will be disabled.

Presentation tools

USB Display(Mac computer)

The projector can display images transferred from a computer via an USB cable (10).

Hardware and software requirement for computer

• OS: Mac OSX 10.5(Intel)

Mac OSX 10.6(Intel)

Mac OSX 10.7(Intel)

Mac OSX 10.8(Intel)

This application is not compatible with Power PC.

• Graphic card: 16 bit, XGA or higher

• Memory: 512 MB or higher

• Hard disk space: 30 MB or higher

Starting USB Display

When you connect your computer to the USB TYPE B port on the projector

using a USB cable, the projector will be recognized as a CD-ROM drive on your

computer. Double click the CD-ROM, then

double click

"LiveViewerLiteForUSB_MacOS.app.".

The application, “LiveViewer Lite for USB”,

will close automatically when the USB

cable is unplugged. However, it may remain

displayed at times.

NOTE • The image transmission from the computer is suspended while the

password-protected screen saver is running. To resume the transmission, exit

the screen saver.

•

If "Waiting for connection." remains displayed while the USB cable is connected,

remove the USB cable and reconnect after a while.

• Check our web site for the latest version of the software and its manual.

(User's Manual (concise))

Follow the instructions that can be obtained at the site for updating.

(continued on next page)

Presentation tools

USB Display(Mac computer) (continued)

NOTE • The “LiveViewer” (refer to the

Network Guide) and this application cannot be used

at the same time. If you connect your computer

to the projector by using a USB cable while the

“LiveViewer” is running, the following message will