FASSTest-2.4GHz Bidirectional Communication System
S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver
R7008SB
1M23N17454
Thank you for purchasing a Futaba R7008SB FASSTest-2.4GHz compatible receiver. The R7008SB receiver features bi-directional communication
with a FASSTest Futaba transmitter using the S.Bus2 port. Using the S.Bus2 port an impressive array of telemetry sensors may be utilized. It also
includes both standard PWM output ports and S.Bus output ports.
Applicable systems: Futaba FASSTest-2.4GHz system transmitter
ꢁ Do not bend the coaxial cable. It causes damage.
Usage precaution
• Analog servos cannot be used with the R7008SB in the FASSTest
12CH mode.
The antennas must be mounted in such a way to assure
they are strain relieved.
• The R7008SB receiver can only be used with FASSTest capable
transmitters.
ꢁ
Keep the antenna as far away from the motor, ESC and
other noise sources as you possibly can.
• Don't connect to Extra Voltage before turning on a receiver.
ꢂ
WARNING
ꢀ
Be sure that the two antennas are placed at 90 degrees to
each other.
• The R7008SB has two antennas. In order to maximize signal reception
and promote safe modeling Futaba has adopted a diversity antenna
system. This allows the receiver to obtain RF signals on both antennas
and fly problem-free.
ꢂ
ꢁ Changes or modification not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
ꢂ The R7008SB receiver should be protected from vibration
by foam rubber, Velcro or similar mounting methods.
Antenna installation for carbon fuselage
Protect from moisture.
WARNING
ꢀ
Keep away from conductive materials to avoid short cir-
cuits.
ꢁ
ꢂ You must leave 30mm at the tip of the antenna fully ex-
posed. The exposed antenna should be secured so that it
cannot move around or back inside of your aircraft.
Antenna installation precaution
ꢁ Do not cut or bundle the receiver antenna wire.
(Antenna installation)
(Typical installation)
Extra Voltage
Port
90˚
It connects with the
battery for power, etc.
External voltage input
cable of an option is
used. The voltage of
the battery can be
displayed with a
＋
S.BUS Servo
Servo for conventional
S.BUS Gyro
－
system
transmitter.
Channel1 output
Channel8 output
HUB
LED
Link/Mode switch
(It is not used for a link.)
S.BUS port (8/SB）
Temperature
Sensor
S.BUS2
Voltage
Antenna
Please refer the table below for LED status vs
receiver's condition.
port
Sensor
R7008SB
(S.BUS2）
HUB
Voltage
Sensor
LED Indication
Battery to 7/B
Green
Off
Red
Solid
Off
Status
Terminal box
RPM
No signal reception
Receiving signals
Sensor
Solid
Altitude
Sensor
Alternate blink
Unrecoverable error (EEPROM, etc.)
HUB
HUB
Altitude
Sensor
Compliance Information Statement
(for U.S.A.)
S.BUS2 Tool
This device, trade name Futaba Corporation of America, model number
R7008SB, complies with part15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
R7008SB Specifications
FASSTest-2.4GHz system(18CH/12CH mode)/S.BUS2 and S.BUS port
and 8 channels for conventional system receiver
(3) This module meets the requirements for a mobile device that may be used
at separation distances of more than 20cm from human body.
To meet the RF exposure requirements of the FCC this device shall not be co-
located with another transmitting device.
The responsible party of this device compliance is:
Futaba Service Center
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.38 oz. (10.9g)
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)
• Battery F/S Voltage: It sets up with a transmitter
• Extra Voltage port: 0 70V DC
～
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
* Be sure that when using ESCs regulated output the capacity of the ESC must
meet your usage condition.
|