1M23N31002
FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz
S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver
◆
◆
R7006SB
Thank you for purchasing a Futaba R7006SB FASSTest-2.4GHz compatible receiver. The R7006SB receiver features bi-directional communication
with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also
includes both standard PWM output ports (1-6ch) and S.BUS output ports. The R7006SB can also be switched the FASST(Multi-ch/7-ch) System.
●
Applicable systems: Futaba FASSTest-2.4GHz / FASST (Multi-ch,7ch) -2.4GHz system transmitter
■ The R7006SB has two antennas. In order to maximize signal reception
Usage precaution
and promote safe modeling Futaba has adopted a diversity antenna system.
This allows the receiver to obtain RF signals on both antennas and fly
problem-free.
• Analog servos cannot be used with the R7006SB in the FASSTest
12CH / FASST High-speed mode.
WARNING
Antenna installation for carbon fuselage
You must leave 30mm at the tip of the antenna fully exposed. The
exposed antenna should be secured so that it cannot move around or
back inside of your aircraft.
Changes or modification not especially approved by the party
responsible for compliance could void the user’ s authority to operate the
equipment.
Be careful of connector insertion
Don't connect an S.BUS servo / gyro to S.BUS2 connector.
Link precaution
The R7006SB receiver should be protected from vibration by foam
rubber, Velcro, or similar mounting methods. Protect from moisture.
Keep away from conductive materials to avoid short circuits.
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable. It causes damage.
Do not perform the linking procedure while the motor's main power
connected or the engine is operating as it may result in serious injury.
When the linking is complete, please cycle the receiver power and
ensure the receiver is properly linked to the transmitter.
The antennas must be mounted in such a way to assure they are strain
Please power up your system in this order. Transmitter first, followed
relieved.
by the receiver.
Keep the antenna as far away from the motor, ESC and other noise
sources as you possibly can.
Be sure that the two antennas are placed at 90 degrees to each other.
If the R7006SB receiver was previously linked to another transmitter,
make sure that transmitter is not operating while linking the receiver to
the new transmitter.
Servo for conventional
system
Antenna
installation
Compliance Information Statement
(for U.S.A.)
S.BUS Gyros
S.BUS servos
This device, trade name Futaba Corporation, model
number R7006SB, complies with part15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
(3) This module meets the requirements for a
mobile device that may be used at separation
distances of more than 20cm from human body.
To meet the RF exposure requirements of the FCC
this device shall not be co-located with another
Channel
Hub
1-6
Telemetry sensor
S.BUS Port (SB)
S.BUS2 Port (SB2)
Telemetry sensor
S.BUS2equipment
Hub
R7006SB
transmitting device.
The responsible party of this device compliance is:
Futaba Service Center
The receiver power supply can
be connected to any port.
3002 N Apollo Drive Suite 1, Champaign, IL
61822 U.S.A.
When all ports are used.
TEL (217)398-8970 or E-mail: support@futaba-rc.
com (Support)
Servo
Y-harness
Battery
3.7 ～ 7.4V
Switch
LED Indication
Link LED
System Mode LED
Status
Link LED
Red Solid
No signal reception
Receiving signals
Green Solid
Start → 2second
later → Red Blink
（1second）
Red Solid
Link/Mode
switch
FASSTest Green Solid
Waiting for link
Mode LED
No signal reception
Receiving signals
Receiving signals but ID is
unmatched
Green Solid
Green Blink
Red Blink
FASST
Off
-
R7006SB Specifications
FASSTest-2.4GHz system(18ch/12ch mode)
Waiting for link
FASST-2.4GHz system (Multi-ch/7ch mode)
FASSTest
FASST
Unrecoverable error (EEPROM, etc.)
Alternate blink
S.BUS2 and S.BUS port and 6ch for conventional system receiver
• Dual antenna diversity
• Size: 0.89 x 1.5 x 0.48 in. (22.5x38.1x12.2mm)
• Weight: 0.28 oz. (8g)
*When on "FASST-7ch" mode, the fail safe function can be set for 3-channel only.
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)
• Battery F/S Voltage: FASSTest---It sets up with a transmitter
FASST---3.8V
*Be sure that when using ESCs regulated output the capacity of the ESC must meet your us-
age condition.
*Never use dry batteries for the power supply of the R7006SB as they may cause difficulties.
|