FUJITSU FI 553PR User Manual

P3PC-1362-01EN  
fi-553PR Imprinter  
Operator's Guide  
Contents  
All Rights Reserved, Copyright © PFU LIMITED 2005.  
The contents of this manual are subject to change without notice.  
This manual may not be reproduced, adapted or translated without prior written permission.  
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED  
CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS.  
While all efforts have been made to ensure the accuracy of all information in this manual, PFU LIMITED assumes no  
liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its  
updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any  
other cause.  
PFU LIMITED further assumes no liability arising from the application or use of any product or system described herein;  
nor any liability for incidental or consequential damages arising from the use of this manual.  
PFU LIMITED disclaims all warranties regarding the information contained herein, whether expressed, implied, or  
statutory.  
PFU LIMITED assumes no liability for incidental or consequential damages arising from the use of this product, and any  
claims by a third party.  
Introduction  
Thank you for purchasing the fi-553PR Imprinter option for  
fi-5530C Color Image Scanner.  
Regulatory Information  
It helps you to organize your documents by printing a name,  
date, time or a serial number on the back side of the scanned  
document.  
This guide explains how to install and use the Imprinter.  
This guide also contains important information such as  
procedures for Print Cartridge replacement. Keep this guide  
in convenient and safe place so that you can refer to it  
whenever necessary.  
FCC declaration  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference will  
not occur in a particular installation. If this  
(For further details about the functions and operations of  
fi-5530C Image Scanner, refer to “fi-5530C Image Scanner  
Operator’s Guide” included in fi-5530C Setup CD-ROM.)  
Manufacturer  
equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is  
encouraged to try to correct the interference by one  
or more of the following measures:  
PFU LIMITED  
Image Products Sales Dept., Imaging Products  
Division, Products Group  
Solid Square East Tower, 580 Horikawa-cho,  
Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,  
Japan  
-
-
Reorient or relocate the receiving antenna.  
Increase separation between equipment and  
receiver.  
Phone : +81 (44) 540-4538  
-
-
Connect equipment to an outlet on a circuit  
different from that to which the receiver is  
located.  
Consult your dealer or an experienced radio/TV  
technician.  
Trademarks  
Microsoft, Windows, and Windows NT are  
registered trademarks of Microsoft Corporation in  
the United States and/or other countries.  
FCC Warning: Changes or modifications not  
expressly approved by the party responsible for  
compliance could void the user’s authority to operate  
the equipment.  
Other product names are the trademarks or  
registered trademarks of the respective companies.  
How Trademarks Are Indicated In This  
Manual  
References to operating systems (OS) are indicated  
as follows:  
Canadian DOC Regulations  
This digital apparatus does not exceed the Class B  
limit for radio noise emissions from digital apparatus  
set out in the Radio interference Regulations of the  
Canadian Department of Communications.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Windows 95:  
Microsoft® Windows® 95 operating  
system.  
Windows NT 4.0: Microsoft® Windows NT® Server  
operating system version 4.0  
Microsoft® Windows NT® Workstation  
operating system version 4.0.  
Windows 98:  
Windows Me:  
Windows 2000:  
Windows XP:  
Microsoft® Windows® 98 operating  
system.  
Le pésent appareil numérique n’ément pas de bruits  
radioélectriques dépassant les limites applicables aux  
appareils numériques de la classe B prescridtes dans  
le Réglesment sur le brouillage radioélectrique dicté  
par le ministere des Communications du Canada.  
Cet appareil numérique de la classe B est conformme  
à la norme NMB-003 du Canada.  
Microsoft® Windows® Millennium  
Edition operating system.  
Microsoft® Windows® 2000  
Professional operating system.  
Microsoft® Windows® XP  
Professional operating system,  
Microsoft® Windows® XP Home  
Edition operating system.  
Where there is no distinction between the different  
versions of the above operating system, the general  
term "Windows" is used.  
fi-553PR Imprinter Operator’s Guide | 1  
 
Bescheinigung des Herstellers /  
Importeurs  
Symbols Used In This Manual  
This manual uses the following symbols in  
explanations in addition to warning indications  
Für den fi-553PR wid folgendes bescheinigt:  
This symbol alerts operators to particularly  
ATTENTION  
important information. Be sure to read this  
information.  
In Übereinsstimmung mit den Bestimmungen  
der EN45014(CE) funkentstört  
This symbol alerts operators to helpful advice  
regarding operation.  
Maschinenlärminformationsverordnung 3.  
GPSGV, 06.01.2004: Der höchste  
HINT  
Schalldruckpegel beträgt 70 dB (A) oder  
weniger, gemäß EN ISO 7779.  
A TRIANGLE symbol indicates that special care  
and attention is required.  
The drawing inside the triangle shows the specific  
caution.  
Use in High-safety Applications  
This product has been designed and manufactured on  
the assumption that it will be used in office, personal,  
domestic, regular industrial, and general-purpose  
applications. It has not been designed and  
A CIRCLE with a diagonal line inside shows action  
which users may not perform.  
The drawing inside or under the circle shows the  
specific action that is not allowed.  
manufactured for use in applications (simply called  
"high-safety applications" from here on) that directly  
involve danger to life and health when a high degree  
of safety is required, for example, in the control of  
nuclear reactions at nuclear power facilities,  
automatic flight control of aircraft, air traffic control,  
operation control in mass-transport systems, medical  
equipment for sustaining life, and missile firing  
control in weapons systems, and when provisionally  
the safety in question is not ensured. The user should  
use this product with adopting measures for ensuring  
safety in such high-safety applications. PFU  
LIMITED assumes no liability whatsoever for  
damages arising from use of this product by the user  
in high-safety applications, and for any claims or  
compensation for damages by the user or a third  
party.  
Outline characters on a colored background show  
instructions users should follow.  
R
It may also include the drawing that shows the  
specific instruction.  
Screen Examples In This Manual  
The screen examples in this manual are subject to  
change without notice in the interest of product  
improvement.  
If the actual displayed screen differs from the screen  
examples in this manual, operate by following the  
actual displayed screen while referring to the User's  
Manual of the scanner application you are using.  
Furthermore, the screenshots in this manual are for  
Windows®, FUJITSU TWAIN 32 Scanner Driver.  
About Maintenance  
Conventions  
The user must not perform repairs on this scanner.  
Contact the store where you purchased the scanner or  
an authorized FUJITSU Image Scanner service  
provider to make repairs to this product.  
Warning Indications Used In This Manual  
This indication alerts operators to an operation  
that, if not strictly observed, may result in  
severe injury or death.  
WARNING  
CAUTION  
This indication alerts operators to an  
operation that, if not strictly observed, may  
result in safety hazards to personnel or  
damage to equipment.  
2 |  
CAUTION  
Safety Precautions  
The following describes important cautions.  
FOLLOW THESE INSTRUCTIONS AND BE SURE TO  
HEED ALL WARNINGS AND CAUTIONS DESCRIBED  
BELOW.  
Install the scanner on a desk so that none of its parts  
protrude outside of the desktop. Also, make sure that  
the scanner is installed on a flat, level surface  
WARNING  
Do not install the scanner on unstable surfaces.  
Install the scanner on a level surface that is free of  
vibration to prevent it from falling.  
Do not touch the power plug with wet hands.  
Doing so might cause electric shock.  
Install the scanner on a strong surface that will  
support the weight of the scanner and other devices.  
Firmly insert the power plug into the power outlet as  
far it can go.  
A damaged AC cable may cause fire or electric  
shock.  
Do not place heavy objects on AC cables, or pull,  
bend, twist, heat, damage or modify AC cables.  
Install the scanner away from strong magnetic fields  
and other sources of electronic noise. Also, protect  
the scanner from static electricity as this might cause  
the scanner to malfunction.  
Also, do not use damaged AC cables or power plugs,  
and AC cables or power plugs when the wall socket  
is loose.  
Do not use aerosol sprays to clean the scanner.  
Aerosol sprays cause dirt and dust to enter the  
scanner, resulting in scanner failure and malfunction.  
Do not use cables other than the ones supplied with  
this product. Use only specified AC cables and  
connector cables. Failure to use the correct cables  
might cause electric shock and equipment failure.  
When the scanner is not used for a long period, be  
sure to disconnect the power plug from the power  
outlet for safety.  
Use this scanner only at the indicated power voltage  
and current. Improper power voltage and current  
might cause fire or electric shock.  
Do not install the scanner in the direct sunlight or  
near heating apparatus. Doing so might cause  
excessive heat to build up inside the scanner,  
causing fire or scanner trouble. Install the scanner in  
a well-ventilated location.  
Also, do not connect to multiple-power strips.  
Wipe off any dust from metal parts on the power plug  
or metal fittings with a soft, dry cloth. Accumulated  
dust might cause fire or electric shock.  
Do not block the ventilation ports. Blocking the  
ventilation ports generates heat inside of scanner,  
which may result in fire or scanner failure.  
Do not install the scanner in locations subject to oil  
smoke, steam, humidity, and dust. Doing so might  
cause a fire or electric shock.  
Do not place heavy objects on the scanner or use the  
scanner's top surface for performing other work.  
Improper installation might cause injuries.  
If you detect heat coming from the device or detect  
other problems such as smoke, strange smells or  
noises, immediately turn off the scanner and then  
disconnect its power plug.  
Do not move the scanner with the power and  
interface cables connected as this might damage the  
cables, causing fire, electric shock or injuries.  
Make sure that the smoking has stopped, and then  
contact the store where you bought the scanner or  
an authorized FUJITSU scanner service provider.  
Before moving the scanner, be sure to disconnect  
the power plug from the power outlet, and disconnect  
data cables. Also, make sure that the floor is free of  
obstructions.  
If the scanner is damaged for any reason, turn off the  
scanner and unplug the power cable before  
contacting the store where you purchased the  
scanner.  
Avoid touching any scanner mechanism when  
scanning as this may cause injuries.  
Do not insert or drop metal objects into the scanner.  
Do not scan wet documents or documents with paper  
clips or staples.  
Do not splash or allow the scanner to get wet.  
If foreign objects (water, small metal objects, liquids,  
etc.) get inside the scanner, immediately turn off the  
scanner and disconnect the power plug from the  
power outlet, then contact the store where you  
bought the scanner or the Maintenance Service  
Center. Pay particular attention to this warning in  
households where there are small children.  
Do not take apart or modify the scanner. The inside  
of the scanner contains high-voltage components.  
Touching these components might cause fire or  
electric shock.  
fi-553PR Imprinter Operator’s Guide | 3  
1. Preparations  
1.1. Checking the Package Contents  
<Imprinter with Scanner Installed>  
Front Side  
When you unpack the Imprinter package, make sure that all  
parts are included.  
Refer to the package contents list included in the Imprinter  
package box.  
ADFAutomatic Document Feeder)  
Cover  
ADF Paper Chute  
If any components are missing, please contact the store  
where you purchased the Imprinter.  
Operator panel  
Function No.  
display  
[Function] button  
[Send to] button  
[Scan] button  
Power button  
1.2. Names and Functions of Parts  
<Imprinter Unit>  
Front Side  
Stacker  
Rear Side  
Imprinter Cover  
Print Section Cover  
Rear Side  
<Inside>  
Fix Tab  
EXT Cable  
(Imprinter Cable)  
Print Cartridge Holder  
Print Section Cover  
4 |  
     
2. Installation  
ATTENTION  
Be careful not to put the Scanner on the  
Fix Tabs or hitting it hard against them.  
You may damage the Fix Tabs.  
2.1. Installing the Imprinter  
Install the Imprinter as follows:  
Be careful not to pinch your finger.  
1. Turn off the Scanner power and disconnect the  
power cable.  
2. Remove the Stacker from the scanner.  
Raise the Stacker upright as shown below while placing your  
fingers under the arms. Push the left arm gently towards the  
outside until you can release it towards you. Then do the  
same with the right arm to remove the Stacker completely.  
After installation  
4. Insert the screws of the Fix Tabs to the rear of the  
scanner and tighten them to secure the Imprinter  
with the Scanner. (2 places)  
d
c
Raise the Stacker up as  
shown below.  
5. Connect the Imprinter cable (EXT Cable) to the  
connector on the rear of the Scanner.  
ATTENTION  
You must remove the stacker before  
installing the Imprinter with the Scanner.  
Do not use force, since this might damage  
the Stacker.  
The Imprinter will not work if the EXT cable is not  
ATTENTION  
connected to the Scanner. Scanning when the EXT  
cable is not connected can cause documents to  
jam inside the Imprinter.  
3. Install the Scanner onto the Imprinter.  
6. Install the Stacker removed in procedure 2 above  
to the Imprinter.  
First, hook one of the arms.  
Fix Tab  
Hold the Scanner above the Imprinter rear. Gently place the  
Scanner onto the Imprinter base while lowering and pushing  
it forward until it touches the Imprinter.  
Then engage the other arm  
by pushing it gently.  
fi-553PR Imprinter Operator’s Guide | 5  
   
7. Connect the power cable to the scanner.  
ATTENTION  
Do not touch the metal part of the Print  
Cartridge nor put the tape back again.  
7. Put the Print Cartridge into the holder as below.  
2.2. Mounting the Print Cartridge  
Mount the print cartridge as follows:  
ATTENTION  
When installing or replacing the Print Cartridge, be  
careful not to insert it out of place.  
1. Confirm that the scanner is turned off.  
2. Grab both ends of the Print Section Cover, pull  
and turn it towards you to open the cover.  
ATTENTION  
Be careful not to let the Print Cartridge catch  
the print circuit film.  
8. Lower the Arm gently until it locks in and fix the  
Print Cartridge in place.  
Print Cartridge Holder  
3. Remove the tape which fixes the Print Cartridge  
Holder.  
9. Move the Print Cartridge Holder to an appropriate  
printing position.  
4. Pinch the Arm with your fingers as shown below  
and release the Arm.  
The holder should be positioned where the printing  
area of document (Section 6) will pass under it.  
5. Take out the Print Cartridge from the bag.  
10. Close the Print Section Cover.  
6. Remove protection tape on the Print Cartridge.  
6 |  
 
2.3. Operation Test  
HINT  
There are following print test patterns:  
After installing the Imprinter, check if the printing operation  
can be done in the Offline Print Test mode of the scanner.  
Test pattern 1(c) (Horizontal):  
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`0000  
0000  
1. While pressing [Function] button on the operator  
Test pattern 2 (2) (Horizontal):  
panel, press  
button.  
abcdefghijklmnopqrstuvwxyz{|}~ 00000000  
Keep pressing [Functionbutton.  
Test pattern 3 (3) (Horizontal):  
!”#$%&()*+,-./0123456789:;<=>?@00000000  
2. Release [Function] button when the Function  
Number Display changes from [P] to [b].  
Test pattern 4 (4) (Vertical):  
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000  
Test pattern 5 (5) (Vertical):  
abcdefghijklmnopqrstuvwxyz{|}~ 00000000  
Function  
Function  
Test pattern 6 (6) (Vertical):  
Function  
!”#$%&()*+,-./0123456789:;<=>?@00000000  
When multiple sheet of documents are set on the  
ADF, the Test print repeats the Pattern from 1 to 6.  
The numbering data portion ”00000000” changes  
from 0 (Zero) with increment of 1(one).  
Send to  
Scan  
Function Number Display  
3. Place a blank document on the ADF paper chute.  
ATTENTION  
Use A4 or Letter size paper. If the size is  
smaller than A4 or Letter, printing may not be  
completed successfully.  
Confirm that the Print Cartridge is positioned  
within the document width.  
6
5mm  
5
4
3
2
c
4. Press [Scan] button.  
Test pattern print sample  
ÖThe paper is fed into the ADF. Test pattern 1 (c of  
the right figure) is printed on the paper starting 5mm  
(the range of error is ±4mm) from its leading edge.  
5. To stop Offline Print Test mode, press button.  
The scanner will be turned off.  
fi-553PR Imprinter Operator’s Guide | 7  
 
3. Basic Operation  
Available items are:  
HINT  
3.1. Setting Printing Position  
Position to start printing (Y offset)  
Font orientation (Horizontal or vertical)  
String to print Max. 40 characters)  
1. Open the Print Section Cover.  
Counter Setup column, add/subtract, step,  
2. Move the Print Cartridge Holder to an appropriate  
printing position.  
etc.)  
For the details, please refer to “FUJITSU TWAIN  
32 Scanner Driver User’s Guide” or “TWAIN  
Driver Help”  
Grab the Print Cartridge Holder as below, slide it to right or  
left (Section 6) and set it at a position where you want to print  
within the printing area of document.  
3.3. Replacing the Print Cartridge  
Replace the Print Cartridge as follows:  
ATTENTION  
When the following message appears, replace the  
Print Cartridge as soon as possible.  
HINT  
The notch on the holder shows the print  
position.  
The Imprinter cover has document size  
markings. You can use them to align the notch  
to adjust the printing position.  
Put the actual document on the ADF to  
confirm that the Print Cartridge is positioned  
within the printing area of the document.  
If you keep on printing without replacing the Print  
Cartridge, light print problem may occur.  
When installing or replacing the Print Cartridge, be  
careful not to insert it out of place.  
1. Press button to turn off the Scanner.  
2. Grab the both ends of the Print Section Cover, pull  
and turn it towards you to open the cover as  
shown below.  
3.2. Print Setup  
You can configure settings of the Imprinter with the scanner  
driver dialog box.  
FUJITSU TWAIN driver (Example)  
In the TWAIN driver dialog box, click [Option] button.  
In [Option] dialog box, choose [Imprinter (Endorser)] tab and  
specify the Imprinter settings.  
Print Cartridge Holder  
8 |  
       
3. Pinch the Arm with your fingers as shown below  
and release the Arm.  
8. Move the Print Cartridge Holder to an appropriate  
printing position.  
The holder should be positioned where the printing  
area of document (Section 6) will pass under it.  
4. Remove the old Print Cartridge.  
When printing close to document edge, be  
ATTENTION  
careful about the position so that characters  
may not be printed off of the document.  
9. Close the Print Section Cover.  
5. Remove the protection tape on the new Print  
Cartridge.  
10. Turn on the scanner.  
11. Reset the Remaining Ink Counter.  
ATTENTION  
You must clear the Remaining Ink counter  
ATTENTION  
Do not touch the metal part of the Print  
whenever you replace the Print Cartridge.  
Cartridge nor put the tape back again.  
For Windows 98, Windows Me, Windows 2000, Windows XP  
6. Put the Print Cartridge into the holder with its tab  
pointing to the right.  
c On the [Start] menu, select [Control panel].  
d Select [Scanners and Cameras].  
e On fi-5530C icon,  
right click and select [Properties] (for Windows Me,  
Windows XP),  
or double click (for Windows 98, Windows 2000).  
f Click the [Device Set] tab.  
g Click the [Clear] button on [Remaining Ink].  
7. Lower the Arm gently until it locks in to fix the Print  
Cartridge in place.  
fi-553PR Imprinter Operator’s Guide | 9  
Click the [OK] button. A confirmation screen appears.  
Then click the [OK] button.  
3. Open the ADF cover.  
Ö The Ink remain counter is reset to 100%.  
ADF Cover  
For Windows 95, Windows NT 4.0  
c Right-click the  
icon in task bar and select [Option].  
Imprinter Cover  
d Click the [Device Setting] tab.  
e Click the [Clear] button on [Remaining Ink].  
3. Remove the jammed documents.  
4. Close the ADF cover.  
ADF Cover  
Imprinter Cover  
Click the [OK] button. A confirmation screen appears.  
Then click the [OK] button.  
Ö The Remaining Ink Counter is reset to 100%.  
3.4. Removing Jammed Documents  
If document jams, remove the jammed document as  
follows:  
5. Grab both ends of the Imprinter Cover and close  
it.  
Open the covers to remove the jammed  
documents.  
ATTENTION  
ADF Cover  
Do not pull out the documents forcefully.  
Imprinter Cover  
1. Remove the documents in the ADF Paper chute.  
2. Grab both ends of the Imprinter Cover, pull and  
turn it towards you to open the cover.  
z
z
Do not move the Imprinter and scanner while  
printing. Printing may be out of order.  
When you do not use the Imprinter for a long  
time, please remove the Print Cartridge from  
the Imprinter and store it.  
ATTENTION  
z
z
Ink will be consumed every time at the initial  
processing by the Imprinter even if no printing is  
performed.  
Do not move the scanner with the Imprinter  
installed. The Imprinter may get damaged.  
10 |  
 
4. Daily Care  
4.1. Cleaning the Print Cartridge  
4.2. Cleaning the Imprinter  
Ink or stains stuck to the nozzle surface of the Print  
Cartridge or leaving the Imprinter unused for a while may  
cause poor print quality due to blocked ink emission holes  
in the nozzle. If your Imprinter has these types of trouble,  
clean the nozzle surface of the Print Cartridge.  
While you use the Imprinter frequently, ink sticks to the  
Imprinter base and that makes the paper dirty.  
As a part of daily maintenance, clean the Imprinter base by  
following the procedure below.  
z
z
When cleaning, gently wipe off dust on the  
Imprinter base with an absorbent item that  
can remove the ink.  
ATTENTION  
For cleaning, use a dry lint-free cloth, and gently  
wipe off dirt and stain from the surface of the  
nozzle. (Do not use tissue.)  
ATTENTION  
If the ink is dried, gently wipe it with a  
moistened cloth. (Since the ink is water  
soluble, it can be cleaned with water.)  
1. Press button to turn off the Scanner.  
2. Remove the Print Cartridge.  
1. Press button to turn off the Scanner.  
2. Open the Print Cartridge Holder Cover and  
remove the Print Cartridge.  
3. Open the Imprinter Cover.  
Nozzle plate  
4. Clean the Print Cartridge Holder base by pressing  
and wiping off the dirt with a lint-free cloth gently  
When cleaning, be careful not to touch the  
ATTENTION  
Nozzle plate or the contact parts of the  
cartridge directly by hand.  
3. Gently wipe off the dirt and stain from the nozzle  
surface with a dry lint-free cloth.  
When cleaning, be careful not to touch the  
ATTENTION  
metal wheels located behind the upper rollers  
on the Print Cartridge Holder Cover.  
4. Make sure that the dirt and stain are all removed  
and then reinstall the Print Cartridge.  
When installing or replacing the Print  
ATTENTION  
Cartridge, be careful not to insert it out of  
place.  
5. Check that the dirt is wiped off, then close the  
Imprinter Cover.  
6. Reinstall the Print Cartridge.  
fi-553PR Imprinter Operator’s Guide | 11  
     
4. Confirm that the dirt or dust is removed from the  
rollers, then close the Imprinter Cover.  
4.3. Cleaning the Rollers  
When ink or paper dust is stuck on the Imprinter feed roller  
surfaces, documents may not feed smoothly. To prevent  
feed problems, clean the roller surfaces regularly.  
Recommended cleaning cycle is every 5,000 sheets.  
HINT  
Actual cleaning cycle may be shorter depending on  
usage and documents.  
1. Open the Imprinter Cover while the scanner is  
turned on.  
2. With lint-free cloth, gently wipe off the dirt or dust  
to clean the roller surfaces.  
Clean lower rubber rollers (total eight) rotating the  
rollers by holding down the [Scan] button and [Send  
to] button on the operator panel of the Scanner.  
Imprinter Cover  
When cleaning, be careful not to touch the  
ATTENTION  
metal wheels located behind the upper rollers  
on the Print Cartridge holder cover.  
3. Clean the Plastic Rollers.  
Clean two black plastic rollers on the inner side of the  
Imprinter Cover.  
Imprinter Cover  
Rotate the rollers with your fingers gently wipe off the  
dirt or dust to clean the roller surface with lint-free  
cloth.  
12 |  
 
5. Error Messages  
If the Function Number Display shows the following  
alternately, the Imprinter requires some intervention by  
customer..  
Function  
Function  
Description: The Print Cartridge is not installed.  
How to solve: Open the Print Section Cover and confirm that  
the Print Cartridge is installed correctly.  
Function  
Function  
Description: A problem occurred to the Imprinter.  
How to solve: cOpen the Print Section Cover and confirm  
that the Print Cartridge is installed correctly.  
dTurn off the scanner and then turn it on again.  
(If the problem occurs again, contact the  
store where you purchased the Imprinter or  
contact an authorized FUJISTU scanner  
service provider.)  
For other errors, refer to “fi-5530C Image Scanner  
ATTENTION  
Operator’s Guide” included in fi-5530C Setup  
CD-ROM.  
fi-553PR Imprinter Operator’s Guide | 13  
 
6. Specifications  
Item  
Specification  
Printing Method  
Print Timing  
Thermal inkjet printing  
Post printing  
Printing Characters  
Alphabet  
: A to Z, a to z  
Numeric Characters : 0, 1 to 9  
Symbols : ! ” $ # % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | }¯  
40 characters (When using 8 digits counter: 43 characters)  
Maximum number of  
characters per line  
Font orientation  
Normal: 0º, 180º (horizontal), 90º, 270º (vertical)  
Narrow: 0º, 180º (horizontal)  
Character size  
Normal : Height 2.91 × width 2.82mm / 0.1146 × 0.1110 in (horizontal),  
Height 2.82 × width 2.91mm / 0.1110 × 0.1146 in (vertical)  
Narrow: Height 2.91 × width 2.12mm / 0.1146 × 0.0835 in (horizontal)  
3.53mm (Normal), 2.54mm (Narrow)  
Character pitch  
Font Style  
Regular, Bold  
Character width  
Normal, Narrow  
Document that can be Documents supported by fi-5530C  
scanned  
For the details, please refer to “fi-5530C Image Scanner Operator’s Guide”-“Chapter 6 Document  
Specification for the ADF.”  
Documents with glossy surface such as thermal paper, thermal transfer paper, coated  
ATTENTION  
paper and art paper, take longer time for the ink to dry and may cause poor print quality.  
The Imprinter must be cleaned more frequently if you use these types of papers.  
Very thick paper or plastic document cannot be scanned when the imprinter is installed.  
Printing area  
D
A = 5mm  
B = 5mm  
C = 5mm  
D = 5mm  
Printing Area  
(Back side)  
C
A
B
Accuracy of Printing  
position  
±4mm from the starting point for feeding direction  
Dimension  
Without Scanner : 399(W) × 302(D) × 151(H) mm  
With Scanner : 399(W) × 546(D) × 352(H) mm  
Without Scanner : 3.5kg  
Weight  
Ambient condition  
Temperature: 10 to 35ºC,  
Humidity: 20 to 80%  
Consumable  
Print Cartridge (P/N: CA00050-0262) Replacement Cycle : 4,000,000 characters  
(The number of characters may decrease depending on the font selection.)  
14 |  
 

York H Re024 User Manual
Sears 47003 User Manual
Panasonic Rod End Bearing Hrt Cr User Manual
Oki B 2520 Mfp User Manual
Mitsubishi Electronics Lossnay Lgh 100rx4 E User Manual
MIELE DRIB XXL User Manual
MAYTAG MEW6627DDS19 User Manual
HARMAN MARTIN EXTERIOR DOT HP User Manual
DEWALT DCF620 User Manual
CRAFTSMAN 247.27373 User Manual