EPSON BRIGHTLINK 536WI User Manual
BrightLink® 536Wi User's Guide  
Contents  
BrightLink 536Wi User's Guide ................................................................................................................ 11  
Introduction to Your Projector ................................................................................................................. 12  
Projector Features.............................................................................................................................. 12  
Product Box Contents.................................................................................................................... 13  
Additional Components ................................................................................................................ 15  
Optional Equipment and Replacement Parts................................................................................. 15  
Warranty and Registration Information.......................................................................................... 17  
Notations Used in the Documentation................................................................................................ 17  
Where to Go for Additional Information .............................................................................................. 18  
Projector Part Locations..................................................................................................................... 18  
Projector Parts - Front/Top ............................................................................................................ 19  
Projector Parts - Rear.................................................................................................................... 20  
Projector Parts - Base.................................................................................................................... 22  
Projector Parts - Control Panel ...................................................................................................... 23  
Projector Parts - Interactive Pen.................................................................................................... 24  
Projector Parts - Remote Control................................................................................................... 25  
Setting Up the Projector ........................................................................................................................... 27  
Projector Placement........................................................................................................................... 27  
Projector Setup and Installation Options ....................................................................................... 27  
Projection Distance........................................................................................................................ 29  
Projector Connections........................................................................................................................ 31  
Connecting to Computer Sources.................................................................................................. 32  
Connecting to a Computer for USB Video and Audio................................................................ 33  
Connecting to a Computer for VGA Video................................................................................. 34  
Connecting to a Computer for HDMI Video and Audio.............................................................. 34  
Connecting to a Computer for Pen Use or USB Mouse Control................................................ 35  
Connecting to a Computer for Sound........................................................................................ 36  
Connecting to Video Sources ........................................................................................................ 36  
Connecting to an HDMI Video Source ...................................................................................... 36  
Connecting to a Component-to-VGA Video Source.................................................................. 37  
3
Connecting to a Composite Video Source ................................................................................ 38  
Connecting to an S-Video Video Source................................................................................... 38  
Connecting to a Video Source for Sound .................................................................................. 39  
Connecting to an External Computer Monitor................................................................................ 39  
Connecting to External Speakers .................................................................................................. 40  
Connecting a Microphone.............................................................................................................. 41  
Connecting to External USB Devices ............................................................................................ 42  
USB Device Projection.............................................................................................................. 42  
Connecting a USB Device or Camera to the Projector.............................................................. 43  
Selecting the Connected USB Source ...................................................................................... 43  
Disconnecting a USB Device or Camera From the Projector.................................................... 44  
Connecting to a Document Camera .............................................................................................. 44  
Connecting Multiple Projectors of the Same Model ....................................................................... 44  
Installing Batteries in the Remote Control .......................................................................................... 45  
Installing Batteries in the Pen............................................................................................................. 47  
Using the Projector on a Network ............................................................................................................ 49  
Wired Network Projection................................................................................................................... 49  
Connecting to a Wired Network ..................................................................................................... 50  
Selecting Wired Network Settings ................................................................................................. 50  
Wireless Network Projection .............................................................................................................. 53  
Installing the Wireless LAN Module ............................................................................................... 54  
Using Quick Wireless Connection (Windows Only) ....................................................................... 56  
Selecting Wireless Network Settings Manually.............................................................................. 56  
Wireless LAN Menu Settings .................................................................................................... 59  
Selecting Wireless Network Settings in Windows.......................................................................... 60  
Selecting Wireless Network Settings in OS X................................................................................ 60  
Setting Up Wireless Network Security ........................................................................................... 61  
Wireless Security Menu Settings .............................................................................................. 62  
Setting Up Projector Network E-Mail Alerts........................................................................................ 62  
Network Projector E-mail Alert Messages ..................................................................................... 63  
Setting Up Monitoring Using SNMP ................................................................................................... 64  
Controlling a Networked Projector Using a Web Browser .................................................................. 65  
Crestron RoomView Support.............................................................................................................. 67  
4
Setting Up Crestron RoomView Support ....................................................................................... 67  
Controlling a Networked Projector Using Crestron RoomView...................................................... 68  
Using Basic Projector Features ............................................................................................................... 70  
Turning On the Projector .................................................................................................................... 70  
Turning Off the Projector .................................................................................................................... 71  
Selecting the Language for the Projector Menus................................................................................ 73  
Adjusting the Image Height ................................................................................................................ 73  
Image Shape...................................................................................................................................... 75  
Correcting Image Shape with the Horizontal Keystone Slider ....................................................... 75  
Correcting Image Shape with the Keystone Buttons...................................................................... 76  
Correcting Image Shape with Quick Corner .................................................................................. 78  
Resizing the Image with the Wide and Tele Buttons .......................................................................... 79  
Focusing the Image Using the Focus Ring......................................................................................... 80  
Remote Control Operation ................................................................................................................. 81  
Using the Remote Control as a Wireless Mouse ........................................................................... 82  
Using the Remote Control as a Pointer.......................................................................................... 83  
Selecting an Image Source ................................................................................................................ 83  
Projection Modes ............................................................................................................................... 85  
Changing the Projection Mode Using the Remote Control ............................................................ 85  
Changing the Projection Mode Using the Menus........................................................................... 86  
Image Aspect Ratio............................................................................................................................ 86  
Changing the Image Aspect Ratio ................................................................................................. 87  
Available Image Aspect Ratios...................................................................................................... 87  
Color Mode......................................................................................................................................... 88  
Changing the Color Mode.............................................................................................................. 89  
Available Color Modes................................................................................................................... 89  
Turning On Auto Iris....................................................................................................................... 90  
Controlling the Volume with the Volume Buttons................................................................................ 91  
Projecting a PC Free Presentation..................................................................................................... 91  
Slideshow Features....................................................................................................................... 92  
Supported PC Free File Types ...................................................................................................... 92  
Starting a Slide Show .................................................................................................................... 93  
PC Free Display Options........................................................................................................... 95  
5
Starting a PC Free Movie Presentation ......................................................................................... 96  
Adjusting Projector Features ................................................................................................................... 98  
Shutting Off the Picture and Sound Temporarily ................................................................................ 98  
Stopping Video Action Temporarily .................................................................................................... 98  
Zooming Into and Out of Images ........................................................................................................ 99  
Projector Security Features.............................................................................................................. 100  
Password Security Types............................................................................................................ 100  
Setting a Password................................................................................................................. 101  
Selecting Password Security Types........................................................................................ 102  
Entering a Password to Use the Projector............................................................................... 103  
Saving a User's Logo Image to Display................................................................................... 104  
Locking the Projector's Buttons ................................................................................................... 106  
Unlocking the Projector's Buttons ........................................................................................... 107  
Installing a Security Cable ........................................................................................................... 107  
Creating a User Pattern to Display ................................................................................................... 107  
Using the Interactive Features ............................................................................................................... 109  
Interactive Modes............................................................................................................................. 109  
Using the Projected Screen as a Whiteboard (Whiteboard Mode)............................................... 109  
Drawing on a Projected Image (PC Free Annotation Mode)........................................................ 111  
Controlling Computer Features from a Projected Screen (PC Interactive Mode)......................... 113  
PC Interactive Mode System Requirements ........................................................................... 115  
Using the Interactive Pens ............................................................................................................... 116  
Using the Pens ............................................................................................................................ 116  
Pen Calibration............................................................................................................................ 119  
Calibrating Automatically ........................................................................................................ 120  
Calibrating Manually ............................................................................................................... 122  
Using BrightLink With a Computer ................................................................................................... 125  
Adjusting the Pen Operation Area ............................................................................................... 125  
Easy Interactive Tools ................................................................................................................. 128  
Windows Pen Input and Ink Tools ............................................................................................... 128  
Enabling Windows Pen Input and Ink Tools............................................................................ 128  
Using Windows Pen Input and Ink Tools................................................................................. 130  
Using BrightLink Without a Computer .............................................................................................. 131  
6
Using PC Free Annotation........................................................................................................... 131  
Built-in Tools for Use Without a Computer................................................................................... 132  
Using the Built-in Whiteboard Mode ............................................................................................ 134  
Changing Pen Width and Color Using the Built-in Toolbar .......................................................... 135  
Projector Control Toolbar ............................................................................................................ 135  
Selecting Network Device Display from the Projector Control Toolbar.................................... 137  
Adjusting the Menu Settings .................................................................................................................. 139  
Using the Projector's Menus............................................................................................................. 139  
Image Quality Settings - Image Menu .............................................................................................. 141  
Input Signal Settings - Signal Menu.................................................................................................. 143  
Projector Feature Settings - Settings Menu...................................................................................... 146  
Projector Setup Settings - Extended Menu....................................................................................... 148  
Projector Network Settings - Network Menu..................................................................................... 154  
Projector Setup Settings - ECO Menu.............................................................................................. 156  
Projector Information Display - Info Menu ........................................................................................ 158  
Event ID Code List....................................................................................................................... 159  
Projector Reset Options - Reset Menu............................................................................................. 160  
Maintaining and Transporting the Projector ......................................................................................... 162  
Projector Maintenance ..................................................................................................................... 162  
Cleaning the Lens........................................................................................................................ 162  
Cleaning the Projector Case........................................................................................................ 163  
Air Filter and Vent Maintenance .................................................................................................. 163  
Cleaning the Air Filter and Vents............................................................................................. 164  
Replacing the Air Filter............................................................................................................ 166  
Projector Lamp Maintenance....................................................................................................... 168  
Replacing the Lamp................................................................................................................ 169  
Resetting the Lamp Timer....................................................................................................... 174  
Replacing the Remote Control Batteries ..................................................................................... 175  
Transporting the Projector................................................................................................................ 176  
Solving Problems.................................................................................................................................... 178  
Projection Problem Tips ................................................................................................................... 178  
Projector Light Status....................................................................................................................... 179  
Using the Projector Help Displays.................................................................................................... 181  
7
Solving Image or Sound Problems................................................................................................... 182  
Solutions When No Image Appears............................................................................................. 182  
Solutions When Image is Incorrect Using the USB Display Function .......................................... 183  
Solutions When "No Signal" Message Appears........................................................................... 184  
Displaying From a PC Laptop ................................................................................................. 184  
Displaying From a Mac Laptop ............................................................................................... 184  
Solutions When "Not Supported" Message Appears................................................................... 185  
Solutions When Only a Partial Image Appears............................................................................ 185  
Solutions When the Image is Not Rectangular ............................................................................ 185  
Solutions When the Image Contains Noise or Static ................................................................... 186  
Solutions When the Image is Fuzzy or Blurry .............................................................................. 187  
Solutions When the Image Brightness or Colors are Incorrect .................................................... 187  
Solutions to Sound Problems ...................................................................................................... 188  
Solutions to Microphone Problems.............................................................................................. 189  
Solving Projector or Remote Control Operation Problems ............................................................... 189  
Solutions to Projector Power or Shut-Off Problems..................................................................... 189  
Solutions to Problems with the Remote Control........................................................................... 190  
Solutions to Password Problems................................................................................................. 191  
Solving Interactive Problems............................................................................................................ 191  
Solutions When "Hardware Device Not Found" Message Appears ............................................. 191  
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears................ 192  
Solutions When the Interactive Pens Do Not Work...................................................................... 192  
Solutions When Manual Calibration Does Not Work.................................................................... 193  
Solutions When the Built-In Toolbar (PC Free Annotation) Does Not Work................................. 193  
Solutions When the Interactive Pen Position Is Not Accurate...................................................... 194  
Solutions When the Interactive Pens Are Slow or Difficult to Use................................................ 194  
Solutions When the Interactive Pens Cause Interference or Unwanted Effects .......................... 195  
Solving Network Problems ............................................................................................................... 195  
Solutions When Network Alert E-Mails are Not Received............................................................ 195  
Solutions When You Cannot Access the Projector Through the Web ......................................... 196  
Where to Get Help............................................................................................................................ 196  
Technical Specifications ........................................................................................................................ 198  
General Projector Specifications...................................................................................................... 198  
8
Projector Lamp Specifications.......................................................................................................... 199  
Remote Control Specifications......................................................................................................... 200  
Projector Dimension Specifications.................................................................................................. 200  
Projector Electrical Specifications .................................................................................................... 200  
Projector Environmental Specifications............................................................................................ 201  
Projector Safety and Approvals Specifications................................................................................. 201  
Supported Video Display Formats.................................................................................................... 202  
USB Display System Requirements................................................................................................. 204  
Notices ..................................................................................................................................................... 206  
Recycling.......................................................................................................................................... 206  
Important Safety Information............................................................................................................ 206  
Important Safety Instructions............................................................................................................ 207  
Restriction of Use ........................................................................................................................ 209  
FCC Compliance Statement............................................................................................................. 210  
Trademarks...................................................................................................................................... 211  
Open Source Software License........................................................................................................ 211  
Copyright Notice............................................................................................................................... 256  
A Note Concerning Responsible Use of Copyrighted Materials................................................... 257  
Copyright Attribution.................................................................................................................... 257  
9
BrightLink 536Wi User's Guide  
Welcome to the BrightLink 536Wi User's Guide.  
11  
 
Introduction to Your Projector  
Refer to these sections to learn more about your projector and this manual.  
Projector Features  
Notations Used in the Documentation  
Where to Go for Additional Information  
Projector Part Locations  
Projector Features  
The BrightLink 536Wi projector includes these special features:  
Unique interactive functions  
• Annotation with or without a computer  
• Annotation with up to two pens at the same time (includes one pen)  
• Enhanced Easy Interactive toolbar for Windows and Mac  
Short-throw projection system  
• Project an 87 inch (221 cm) image (16:10) from just 35.7 inches (90 cm) away  
• Easily mounted to the wall for fast, low-cost installations  
• Reduced shadow interference and glare  
Bright, high-resolution projection system  
• Up to 3400 lumens of color brightness (color light output) and 3400 lumens of white brightness (white  
light output)  
Note: Color brightness (color light output) and white brightness (white light output) will vary depending  
on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output  
measured in accordance with ISO 21118.  
• Native resolution of 1280 × 800 pixels (WXGA)  
Flexible connectivity  
• Plug-and-play 3-in-1 USB projection, audio, and mouse control for instant setup  
• HDMI port for computer or video device connection  
• Wired network support for projection, monitoring, and control via remote network computer  
12  
   
• Optional wireless network support, including video and audio transfer  
• PC Free photo slide shows via connected USB memory devices or Epson document camera  
• Dual VGA ports for connections by multiple presenters  
• Port for connecting an external monitor or second projector  
• Port for connecting a microphone  
Innovative display and operation features  
• Low total cost of ownership with long-life projector lamp and high-efficiency air filter  
• High zoom ratio for larger images in shorter projection distances  
• 16000:1 contrast ratio and Auto Iris control for crisply detailed images  
• Built-in closed captioning decoder  
• Powerful 16 W speaker system with audio out port for connecting external speakers  
• Epson's Instant Off and Direct Power On features for quick setup and shut down  
• Support for Crestron RoomView network monitoring systems  
• Network message broadcast system to project timely messages to all networked projectors  
Product Box Contents  
Additional Components  
Optional Equipment and Replacement Parts  
Warranty and Registration Information  
Parent topic: Introduction to Your Projector  
Related concepts  
Projector Part Locations  
Product Box Contents  
Save all the packaging in case you need to ship the projector. Always use the original packaging (or  
equivalent) when shipping.  
13  
 
Make sure your projector box included all of these parts:  
1
2
3
4
5
6
7
8
9
Projector  
Lens cover  
Remote control  
Remote control batteries (two AA alkaline)  
Power cord  
VGA computer cable  
Password Protected sticker  
Projector documentation CD-ROM  
Projector software CD-ROM  
14  
10 Interactive pen and battery (one AA alkaline)  
Parent topic: Projector Features  
Related concepts  
Projector Connections  
Additional Components  
Depending on how you plan to use the projector, you may need to obtain the following additional  
components:  
• To receive a composite video signal, you need an RCA-style video or A/V cable. See your local  
computer or electronics dealer for purchase information.  
• To receive an S-Video signal, you need an S-Video cable compatible with your device. See your local  
computer or electronics dealer for purchase information.  
• To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You  
can purchase one from Epson or an authorized Epson reseller.  
• To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or  
an authorized Epson reseller.  
Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for  
video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.  
Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not  
support audio through the HDMI port.  
• To project with audio from certain ports, you may need a commercially available audio cable  
compatible with your device. See your local computer or electronics dealer for purchase information.  
• To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video  
output to the projector's VGA video port, you need to obtain an adapter. Contact Apple for compatible  
adapter options.  
Parent topic: Projector Features  
Optional Equipment and Replacement Parts  
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized  
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online  
at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).  
Epson offers the following optional accessories and replacement parts for your projector:  
15  
   
Option or part  
Part number  
V13H010L87  
V13H134A47  
V12H418P12  
V12H005M09  
V12H666010  
V12H667010  
V12H590001  
V12H668010  
V12HMSS020  
Genuine Epson replacement lamp (ELPLP87)  
Air filter replacement (ELPAF47)  
Wireless LAN module (ELPAP07)  
Quick Wireless Connection USB key (ELPAP09)  
Additional interactive pen A (ELPN04A) (orange)  
Additional interactive pen B (ELPN04B) (blue)  
Interactive pen extension  
Replacement interactive pen tips  
Mimio Studio Interactive software  
SMART Notebook software  
V12HSSW020  
V12H321005  
V12H377020  
V12H594020  
V12H500020  
V12H614020  
V12H005C28  
V12H467020  
V12H706020  
ELPMBPJF  
ELPMBP01  
ELPMBP02  
ELPMBP03  
ELPMBC01  
ELPSL01  
Epson DC-06 document camera (ELPDC06)  
Epson DC-11 document camera (ELPDC11)  
Epson DC-12 document camera (ELPDC12)  
Epson DC-20 document camera (ELPDC20)  
PowerLite Pilot 2 (ELPCB02)  
Remote control cable set (ELPKC28)  
Active speakers (ELPSP02)  
Short Throw Wall Mount (ELPMB45)  
Universal projector ceiling mount  
Adjustable suspended ceiling channel kit  
False ceiling plate kit  
Structural round ceiling plate  
Adjustable extension column (pipe) 8" - 11" (20 to 28 cm)  
Kensington security lock  
90-inch whiteboard  
V12H468002  
16  
Option or part  
Part number  
V12H468001  
ELPSC80  
96-inch whiteboard  
Accolade Duet portable projector screen  
Component-to-VGA video cable (ELPKC19)  
1-Year Extended Depot Repair Service Plan  
1-Year Extended Exchange Service Plan  
2-Year Extended Depot Repair Service Plan  
2-Year Extended Exchange Service Plan  
V12H005C19  
EPPFTPA1  
EPPEXPA1  
EPPFTPA2  
EPPEXPA2  
Parent topic: Projector Features  
Warranty and Registration Information  
Your projector comes with a basic warranty that lets you project with confidence. For details, see the  
warranty that came with your projector.  
In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you  
won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere  
in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.  
Register your product online using the projector CD or at this site: epson.com/webreg.  
Registering also lets you receive special updates on new accessories, products, and services.  
Parent topic: Projector Features  
Notations Used in the Documentation  
Follow the guidelines in these notations as you read your documentation:  
• Warnings must be followed carefully to avoid bodily injury.  
• Cautions must be observed to avoid damage to your equipment.  
• Notes contain important information about your projector.  
• Tips contain additional projection information.  
Parent topic: Introduction to Your Projector  
17  
   
Where to Go for Additional Information  
Need quick help on using your projector? Here's where to look for help:  
• Built-in help system  
Press the Help button on the remote control or projector to get quick solutions to common problems.  
• epson.com/support (U.S) or epson.ca/support (Canada)  
View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24  
hours a day.  
• For detailed instructions on using your projector in a network environment, see the EasyMP Network  
Projection Operation Guide.  
• For detailed instructions on monitoring your projector in a network environment (Windows only), see  
the EasyMP Monitor Operation Guide.  
• For detailed instructions on using your projector to hold interactive meetings in a network environment,  
see the EasyMP Multi PC Projection Operation Guide.  
• For detailed instructions on using your computer to draw on projected images, see the Easy  
Interactive Tools Operation Guide.  
• If you still need help after checking this manual and the sources listed above, you can use the Epson  
PrivateLine Support service to get help fast. For details, see "Where to Get Help".  
Parent topic: Introduction to Your Projector  
Related references  
Where to Get Help  
Projector Part Locations  
Check the projector part illustrations to learn about the parts on your projector.  
Projector Parts - Front/Top  
Projector Parts - Rear  
Projector Parts - Base  
Projector Parts - Control Panel  
Projector Parts - Interactive Pen  
Projector Parts - Remote Control  
Parent topic: Introduction to Your Projector  
18  
   
Projector Parts - Front/Top  
1
2
3
4
5
6
7
8
Remote control receiver  
Interactive pen receiver  
Foot release lever  
Front adjustable foot  
Projector lens  
Air intake vent (air filter)  
Horizontal keystone slider  
Focus ring  
19  
 
9
Control panel  
10 Lamp cover  
11 Exhaust vent  
12 A/V Mute button and Auto Calibration button (hold down for 3 seconds to auto calibrate)  
13 Lens cover  
Parent topic: Projector Part Locations  
Projector Parts - Rear  
1
Power inlet  
2
3
4
5
6
7
S-Video port  
RS-232C port  
Video port  
L-Audio-R ports  
Mic (microphone) port  
Monitor Out port  
20  
 
8
9
Audio1 port  
Audio Out port  
10 Audio2 port  
11 SYNC In/Out ports  
12 Speaker  
13 HDMI port  
14 Computer2 port  
15 Computer1 port  
16 Remote receiver  
17 Network (LAN) port  
18 USB-B port  
19 USB-A port  
20 Wireless LAN unit cover screw  
Parent topic: Projector Part Locations  
21  
Projector Parts - Base  
1
2
3
4
5
Ceiling mount holes (3)  
Wall mount holes (5)  
Security cable attachment point  
Rear feet  
Front adjustable foot  
22  
 
Parent topic: Projector Part Locations  
Projector Parts - Control Panel  
1
Status lights  
2
3
4
5
6
7
Source Search button (searches for connected video sources)  
Enter button (selects options)  
Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons  
Help button (accesses projector help information)  
Esc button (cancels/exits functions)  
Wide/Tele buttons (adjust projected image size), horizontal keystone adjustment buttons (adjust  
screen shape), and arrow buttons  
8
9
Menu button (accesses projector menu system)  
Power button and light  
Parent topic: Projector Part Locations  
Related references  
Projector Light Status  
23  
 
Projector Parts - Interactive Pen  
1
2
3
4
5
Pen tip  
Battery light  
Power/function button  
Attachment for optional strap or cord  
Battery cover  
Parent topic: Projector Part Locations  
24  
 
Projector Parts - Remote Control  
1
Power button  
25  
 
2
3
4
5
6
7
8
9
Computer button (cycles through connected computer sources)  
Video button (cycles through connected video sources)  
Numeric buttons (enter numbers)  
Auto button (automatically adjusts position, tracking, and sync settings)  
Aspect button (selects the image aspect ratio)  
Num button (when held down, switches numeric buttons to number function)  
Menu button (accesses projector menu system)  
Arrow buttons (move through on-screen options and control wireless mouse functions)  
10 Enter button (selects options and controls wireless mouse functions)  
11 User button (customizable for different functions)  
12 Page up/down buttons (control presentation slides)  
13 E-Zoom +/– buttons (zoom into and out of the image)  
14 A/V Mute button (turns off picture and sound)  
15 Help button (accesses projector help information)  
16 Freeze button (stops video action)  
17 Volume up/down buttons (adjust speaker volume)  
18 Pointer button (activates on-screen pointer)  
19 Esc button (cancels/exits functions and controls wireless mouse functions)  
20 Pen Mode button (cycles between PC Interactive and PC Free Annotation modes)  
21 Color Mode button (selects display modes)  
22 MHL Menu button (not active)  
23 LAN button (cycles between network and optional Quick Wireless Connection USB Key sources)  
24 USB button (cycles through connected USB sources)  
25 Source Search button (searches for connected sources)  
Parent topic: Projector Part Locations  
Related references  
Remote Control Operation  
26  
Setting Up the Projector  
Follow the instructions in these sections to set up your projector for use.  
Projector Placement  
Projector Connections  
Installing Batteries in the Remote Control  
Installing Batteries in the Pen  
Projector Placement  
You can place the projector on almost any flat surface to project an image.  
You can also install the projector in a ceiling or wall mount if you want to use it in a fixed location.  
Keep these considerations in mind as you select a projector location:  
• Place the projector on a sturdy, level surface or install it using a compatible mount.  
• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or  
next to anything that could block the vents.  
• Position the projector within reach of a grounded electrical outlet or extension cord.  
Projector Setup and Installation Options  
Projection Distance  
Parent topic: Setting Up the Projector  
Projector Setup and Installation Options  
You can set up or install your projector in the following ways:  
Front  
27  
     
Rear  
Front ceiling  
Rear ceiling  
28  
Wall-mounted  
Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an  
angle.  
If you project from the ceiling or wall, or from the rear, be sure to select the correct Projection option in  
the projector's menu system.  
Note: Interactivity is not available when using rear or rear ceiling projection.  
Parent topic: Projector Placement  
Related references  
Projector Setup Settings - Extended Menu  
Projection Distance  
The distance at which you place the projector from the screen determines the approximate size of the  
image. The image size increases the farther the projector is from the screen, but can vary depending on  
the zoom factor, aspect ratio, and other settings.  
Use the tables here to determine approximately how far to place the projector from the screen based on  
the size of the projected image. (Conversion figures may have been rounded up or down.) For more  
detailed information and installation instructions for the wall mount, see the Installation Guide. You can  
29  
 
also use the projector Throw Distance Calculator at epson.com/support (U.S.) or epson.ca/support  
(Canada).  
16:10 Aspect Ratio  
Screen or image  
size  
Projection distance (1)  
Wide to Tele  
Offset from lens center (2)  
55 inches  
60 inches  
70 inches  
80 inches  
90 inches  
100 inches  
116 inches  
22 to 30 inches (56 to 77 cm)  
24 to 33 inches (61 to 84 cm)  
28 to 39 inches (72 to 99 cm)  
33 to 45 inches (83 to 113 cm)  
37 inches (94 cm)*  
3.4 inches (9 cm)  
3.7 inches (9 cm)  
4.4 inches (11 cm)  
5 inches (13 cm)  
5.6 inches (14 cm)  
6.2 inches (16 cm)  
7.2 inches (18 cm)  
41 inches (105 cm)*  
48 inches (122 cm)*  
* Wide resolution only  
30  
4:3 Aspect Ratio  
Screen or image  
size  
Projection distance (1)  
Wide to Tele  
Offset from lens center (2)  
50 inches  
60 inches  
70 inches  
80 inches  
90 inches  
102 inches  
23 to 31 inches (58 to 79 cm)  
28 to 38 inches (70 to 96 cm)  
32 to 44 inches (82 to 112 cm)  
37 inches (94 cm)*  
3.5 inches (9 cm)  
4.2 inches (11 cm)  
4.9 inches (13 cm)  
5.6 inches (14 cm)  
6.3 inches (16 cm)  
7.2 inches (18 cm)  
42 inches (107 cm)*  
48 inches (121 cm)*  
* Wide resolution only  
16:9 Aspect Ratio  
Screen or image  
size  
Projection distance (1)  
Wide to Tele  
Offset from lens center (2)  
60 inches  
70 inches  
80 inches  
90 inches  
100 inches  
113 inches  
25 to 34 inches (63 to 87 cm)  
29 to 40 inches (74 to 101 cm)  
34 to 46 inches (85 to 116 cm)  
38 inches (97 cm)*  
5.5 inches (14 cm)  
6.4 inches (16 cm)  
7.3 inches (19 cm)  
8.2 inches (21 cm)  
9.1 inches (23 cm)  
10.3 inches (26 cm)  
42 inches (108 cm)*  
48 inches (122 cm)*  
* Wide resolution only  
Parent topic: Projector Placement  
Projector Connections  
You can connect the projector to a variety of computer, video, and audio sources to display  
presentations, movies, or other images, with or without sound.  
• Connect any type of computer that has a USB port, standard video output (monitor) port, or HDMI port.  
31  
 
• For video projection, connect devices such as DVD players, gaming consoles, digital cameras, and  
smartphones with compatible video output ports.  
• If your presentation or video includes sound, you can connect audio input cables, if necessary.  
• For slide shows without a computer, you can connect USB devices (such as a flash drive or camera)  
or an optional Epson document camera.  
Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode  
to ensure the projector's internal temperature is regulated properly.  
Connecting to Computer Sources  
Connecting to Video Sources  
Connecting to an External Computer Monitor  
Connecting to External Speakers  
Connecting a Microphone  
Connecting to External USB Devices  
Connecting to a Document Camera  
Connecting Multiple Projectors of the Same Model  
Parent topic: Setting Up the Projector  
Related references  
Product Box Contents  
Projector Setup Settings - Extended Menu  
Connecting to Computer Sources  
Follow the instructions in these sections to connect a computer to the projector.  
Connecting to a Computer for USB Video and Audio  
Connecting to a Computer for VGA Video  
Connecting to a Computer for HDMI Video and Audio  
Connecting to a Computer for Pen Use or USB Mouse Control  
Connecting to a Computer for Sound  
Parent topic: Projector Connections  
32  
 
Connecting to a Computer for USB Video and Audio  
If your computer meets the system requirements, you can send video and audio output to the projector  
through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a  
USB cable.  
Note: This also lets you use the interactive pen with your computer. You need to change the USB Type  
B setting in the projector's Extended menu before you can project through the USB port. Note that using  
USB Display will slow interactive pen function. For the best performance, VGA or HDMI connections are  
recommended.  
1. Turn on your computer.  
2. Connect the cable to your projector's USB-B port.  
3. Connect the other end to any available USB port on your computer.  
4. To use USB Display, do one of the following:  
• Windows 8.x: Click EPSON_PJ_UD in the upper right-corner, then select Run EMP_UDSE.exe  
in the dialog box that appears to install the Epson USB Display software.  
• Windows 7/Windows Vista: Select Run EMP_UDSE.exe in the dialog box that appears to install  
the Epson USB Display software.  
• Windows XP: Wait as messages appear on your computer screen and the projector installs the  
Epson USB Display software on your computer.  
• Windows 2000: Select Computer, EPSON_PJ_UD, and EMP_UDSE.EXE to install the Eposn  
USB Display software.  
• OS X: The USB Display setup folder appears on your screen. Select USB Display Installer and  
follow the on-screen instructions to install the Epson USB Display software.  
Follow any on-screen instructions. You need to install this software only the first time you connect  
the projector to the computer.  
33  
 
The projector displays the image from your computer's desktop and outputs sound, if your presentation  
contains audio.  
Parent topic: Connecting to Computer Sources  
Connecting to a Computer for VGA Video  
You can connect the projector to your computer using a VGA computer cable.  
Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for  
video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.  
Contact Apple for compatible adapter options.  
1. If necessary, disconnect your computer's monitor cable.  
2. Connect the VGA computer cable to your computer's monitor port.  
3. Connect the other end to a Computer port on the projector.  
4. Tighten the screws on the VGA connector.  
Parent topic: Connecting to Computer Sources  
Connecting to a Computer for HDMI Video and Audio  
If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.  
Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for  
video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.  
Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support  
audio through the HDMI port.  
1. Connect the HDMI cable to your computer's HDMI output port.  
34  
   
2. Connect the other end to the projector's HDMI port.  
Parent topic: Connecting to Computer Sources  
Connecting to a Computer for Pen Use or USB Mouse Control  
If you connected your computer to a Computer or HDMI port on the projector, you also need to connect  
the USB cable so you can use the pens with your computer.  
Connecting the USB cable also lets you set up the remote control to act as a wireless mouse, but you  
cannot use this feature at the same time you are using the pens with your computer.  
1. Connect the USB cable to your projector's USB-B port.  
2. Connect the other end to any available USB port on your computer.  
If you want to use the remote control as a wireless mouse, you need to change the USB Type B setting  
in the projector's Extended menu. You may also need to configure your computer to work with an  
external USB mouse. See your computer documentation for details.  
Parent topic: Connecting to Computer Sources  
Related references  
Projector Parts - Remote Control  
35  
 
Related tasks  
Using the Remote Control as a Wireless Mouse  
Connecting to a Computer for Sound  
If your computer presentation includes sound and you did not connect it to the projector's USB-B or  
HDMI port, you can still play sound through the projector's speaker system. Just connect an optional  
3.5 mm stereo mini-jack audio cable as described here.  
1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or  
audio-out port.  
2. Connect the other end to the Audio port that corresponds to the Computer port you are using.  
Parent topic: Connecting to Computer Sources  
Connecting to Video Sources  
Follow the instructions in these sections to connect video devices to the projector.  
Connecting to an HDMI Video Source  
Connecting to a Component-to-VGA Video Source  
Connecting to a Composite Video Source  
Connecting to an S-Video Video Source  
Connecting to a Video Source for Sound  
Parent topic: Projector Connections  
Connecting to an HDMI Video Source  
If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.  
The HDMI connection provides the best image quality.  
1. Connect the HDMI cable to your video source's HDMI output port.  
36  
     
2. Connect the other end to the projector's HDMI port.  
Parent topic: Connecting to Video Sources  
Connecting to a Component-to-VGA Video Source  
If your video source has component video ports, you can connect it to the projector using an optional  
component-to-VGA video cable. Depending on your component ports, you may need to use an adapter  
cable along with a component video cable.  
1. Connect the component connectors to your video source's color-coded component video output  
ports, usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using an adapter, connect these connectors  
to your component video cable.  
2. Connect the VGA connector to a Computer port on the projector.  
3. Tighten the screws on the VGA connector.  
If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's  
Signal menu.  
Parent topic: Connecting to Video Sources  
37  
 
Related references  
Input Signal Settings - Signal Menu  
Connecting to a Composite Video Source  
If your video source has a composite video port, you can connect it to the projector using an optional  
RCA-style video or A/V cable.  
1. Connect the cable with the yellow connector to your video source's yellow video output port.  
2. Connect the other end to the projector's Video port.  
Parent topic: Connecting to Video Sources  
Connecting to an S-Video Video Source  
If your video source has an S-Video port, you can connect it to the projector using an optional S-Video  
cable.  
1. Connect the S-Video cable to your video source's S-Video output port.  
2. Connect the other end to the projector's S-Video port.  
Parent topic: Connecting to Video Sources  
38  
   
Connecting to a Video Source for Sound  
You can play sound through the projector's speaker system if your video source has audio output ports.  
If you are projecting video using a Computer port, connect the projector to the video source using an  
optional stereo mini-jack audio cable.  
If you are projecting video using the Video or S-Video port, connect the projector to the video source  
using an RCA audio cable.  
Note: If you connected your video source to the projector using an HDMI cable, the audio signal is  
transferred with the video signal; you do not need an additional cable for sound.  
1. Connect the audio cable to your video source's audio-out ports.  
2. Do one of the following:  
• Connect the other end of the cable to the projector's Audio port that corresponds to the  
Computer port you are using for video.  
• Connect the red and white plugs on the other end of the cable to the projector's L-Audio-R ports.  
Parent topic: Connecting to Video Sources  
Connecting to an External Computer Monitor  
If you connected the projector to a computer using a Computer port, you can also connect an external  
monitor to the projector. This lets you see your presentation on the external monitor even when the  
projected image is not visible.  
If you want to output images to an external monitor when the projector is turned off, you need to select  
Communication On as the Standby Mode setting and Always On as the A/V Output setting in the  
projector's menu system.  
39  
   
Note: Monitors that use a refresh rate less than 60 Hz may not be able to display images correctly.  
1. Make sure your computer is connected to the projector's Computer port. If there are two computer  
ports, make sure you use the Computer1 port.  
2. Connect the external monitor's cable to your projector's Monitor Out port.  
Note: Only analog RGB signals from the Computer 1 port can be output to an external monitor.  
Note: Content you draw using the interactive features is not displayed on an external monitor unless  
you draw it using Easy Interactive Tools.  
Parent topic: Projector Connections  
Connecting to External Speakers  
To enhance the sound from your presentation, you can connect the projector to external self-powered  
speakers. You can control the volume using the projector's remote control.  
You can also connect the projector to an amplifier with speakers.  
If you want to output audio from the external speakers when the projector is turned off, you need to  
select Communication On for the Standby Mode setting and Always On for the A/V Output setting in  
the projector's menu system.  
Note: The projector's built-in speaker system is disabled when you connect external speakers.  
1. Make sure your computer or video source is connected to the projector with both audio and video  
cables as necessary.  
2. Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pin-  
jack cable, or another type of cable or adapter.  
3. Connect one end of the cable to your external speakers as necessary.  
40  
 
4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port.  
Parent topic: Projector Connections  
Related references  
Projector Setup Settings - Extended Menu  
Connecting a Microphone  
You can connect a microphone to the projector's Mic port to provide audio support during presentations.  
Note: The projector supports powered or dynamic microphones only. If you want to output audio from  
the microphone when the projector is turned off, you need to select Communication On for the  
Standby Mode setting and Always On for the A/V Output setting in the projector's menu system.  
1. Connect the microphone cable to the projector's Mic port.  
2. Turn on the microphone, if necessary.  
Parent topic: Projector Connections  
Related references  
Projector Setup Settings - Extended Menu  
41  
 
Connecting to External USB Devices  
Follow the instructions in these sections to connect external USB devices to the projector.  
USB Device Projection  
Connecting a USB Device or Camera to the Projector  
Selecting the Connected USB Source  
Disconnecting a USB Device or Camera From the Projector  
Parent topic: Projector Connections  
USB Device Projection  
You can project images and other content without using a computer or video device by connecting any of  
these devices to your projector:  
• USB flash drive  
• Digital camera or smartphone  
• USB hard drive  
• Multimedia storage viewer  
• USB memory card reader  
Note: Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices,  
and must be USB Mass Storage Class-compliant.  
Note: USB hard drives must meet these requirements:  
• USB Mass Storage Class-compliant (not all USB Mass Storage Class devices are supported)  
• Formatted in FAT or FAT32  
• Self-powered by their own AC power supplies (bus-powered hard drives are not recommended)  
• Does not have multiple partitions  
You can project slide shows from image files on a connected USB device or memory card reader.  
Parent topic: Connecting to External USB Devices  
Related topics  
Projecting a PC Free Presentation  
42  
   
Connecting a USB Device or Camera to the Projector  
You can connect your USB device or camera to the projector's USB-A port and use it to project images  
and other content.  
1. If your USB device came with a power adapter, plug the device into an electrical outlet.  
2. Connect the USB cable (or USB flash drive or USB memory card reader) to the projector's USB-A  
port.  
Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not  
operate correctly.  
3. Connect the other end of the cable (if applicable) to your device.  
Parent topic: Connecting to External USB Devices  
Related topics  
Projecting a PC Free Presentation  
Selecting the Connected USB Source  
You can switch the projector's display to the source you connected to the USB-A port.  
1. Make sure the connected USB source is turned on, if necessary.  
2. Press the USB button on the remote control.  
3. Press the button again to cycle through other USB sources, if available.  
Parent topic: Connecting to External USB Devices  
43  
   
Disconnecting a USB Device or Camera From the Projector  
When you finish presenting with a connected USB device or camera, you must prepare to disconnect the  
device from the projector.  
1. If the device has a power button, turn off and unplug the device.  
2. Disconnect the USB device or camera from the projector.  
Parent topic: Connecting to External USB Devices  
Connecting to a Document Camera  
You can connect an Epson document camera to your projector to project images viewed by the camera.  
Depending on your document camera model, do one of the following to connect the document camera to  
your projector:  
• For the Epson DC-06 document camera, locate the USB cable that came with the camera and  
connect it to the to the projector's USB-A port and to the document camera's USB Type B port.  
• For the Epson DC-11 document camera, connect it to the projector's Computer or Video port and to  
the corresponding port on the document camera. See the document camera manual for details.  
• For the Epson DC-12 document camera, connect it to the projector's HDMI, Computer, or Video port  
and to the corresponding port on the document camera. See the document camera manual for details.  
• For the Epson DC-20 document camera, connect it to the projector's HDMI, Computer, or Video port  
and to the corresponding port on the document camera. See the document camera manual for details.  
Note: For additional features supported by software, connect your document camera to your computer  
instead of the projector. See the document camera manual for details.  
Parent topic: Projector Connections  
Related references  
Optional Equipment and Replacement Parts  
Connecting Multiple Projectors of the Same Model  
If you use the interactive features of multiple projectors of the same model in the same room, you need  
to synchronize the projectors. To do this, connect the optional remote control cable set (V12H005C28) to  
the SYNC port on each projector.  
44  
     
1. Connect one end of the remote control cable to the SYNC In port on one projector, and connect the  
other end to the SYNC Out port on the other projector.  
Note: If you are connecting three or more projectors, connect the projectors in a chain as shown.  
2. In the Extended menu, set the Sync of Projectors setting to Wired.  
Note: If you are using the projector in the same room as another projector that does not support  
cable connection or if you do not have the optional remote control cable, set the Wired Sync Mode  
setting to Mode 2 in the projector's Extended menu.  
Parent topic: Projector Connections  
Installing Batteries in the Remote Control  
The remote control uses the two AA batteries that came with the projector.  
Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,  
or mix new and old batteries.  
45  
 
1. Remove the battery cover.  
2. Insert the batteries with the + and – ends facing as shown.  
46  
3. Replace the battery cover and press it down until it clicks into place.  
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat  
or flame. Keep batteries out of the reach of children; they are choking hazards and are very  
dangerous if swallowed.  
Parent topic: Setting Up the Projector  
Installing Batteries in the Pen  
The pen uses one AA battery.  
1. Remove the battery cover as shown.  
47  
 
2. Insert the battery with the + and – ends facing as shown.  
3. Replace the battery cover and press it down until it clicks into place.  
Parent topic: Setting Up the Projector  
48  
Using the Projector on a Network  
Follow the instructions in these sections to set up your projector for use on a network.  
Wired Network Projection  
Wireless Network Projection  
Setting Up Projector Network E-Mail Alerts  
Setting Up Monitoring Using SNMP  
Controlling a Networked Projector Using a Web Browser  
Crestron RoomView Support  
Wired Network Projection  
You can send images to your projector through a wired network. To do this, you connect the projector to  
your network, and then set up your projector and computer for network projection.  
After connecting and setting up the projector as described here, install the network software from the  
Epson Projector Software CD or download the software as necessary. Use the following software and  
documentation to set up, control, and monitor network projection:  
• EasyMP Network Projection software sets up your computer for network projection. See the EasyMP  
Network Projection Operation Guide for instructions.  
• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the  
network. You can download the latest software and documentation from the Epson web site. Go to  
epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.  
• EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the  
computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guide for  
instructions.  
• EasyMP Network Updater software (Windows only) allows you to update firmware for a projector over  
a wired LAN. See the EasyMP Network Updater Operation Guide for instructions. You can download  
the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or  
epson.ca/support (Canada) and select your projector.  
• Projection from iOS or Android devices using the free Epson iProjection app (if your projector is  
connected to a network that includes a wireless access point); visit epson.com/projectorapp (U.S.) or  
epson.ca/projectorapp (Canada) for more information.  
49  
   
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,  
you can connect to the projector wirelessly through the access point using the EasyMP Network  
Projection software.  
Connecting to a Wired Network  
Selecting Wired Network Settings  
Parent topic: Using the Projector on a Network  
Related references  
Projector Network Settings - Network Menu  
Connecting to a Wired Network  
To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network  
cable. To ensure proper data transmission, use a Category 5 shielded cable or better.  
1. Connect one end of the network cable to your network hub, switch, or router.  
2. Connect the other end of the cable to the projector's LAN port.  
Parent topic: Wired Network Projection  
Selecting Wired Network Settings  
Before you can project from computers on your network, you must select the network settings for the  
projector using its menu system.  
Note: Make sure you already connected the projector to your wired network using the LAN port.  
1. Turn on the projector.  
2. Press the Menu button.  
50  
   
3. Select the Network menu and press Enter.  
4. Select Network Configuration and press Enter.  
5. Select the Basic menu and press Enter.  
6. Select the following basic options as necessary:  
• Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the  
projector over the network.  
51  
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the  
PJLink protocol for projector control.  
• Web Control Password lets you enter a password up to 8 alphanumeric characters long for  
accessing the projector over the web. (Default user name is EPSONWEB; default password is  
admin.)  
• Projector Keyword lets you turn on a security password to prevent access to the projector by  
anyone not in the room with it. You must enter a displayed, randomized keyword from a computer  
using the EasyMP Network Projection software to access the projector.  
Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow  
buttons on the remote control to highlight characters and press Enter to select them.  
7. Select the Wired LAN menu and press Enter.  
8. If necessary, select IP Settings and press Enter.  
9. Select your IP Settings as necessary:  
• If your network assigns addresses automatically, turn on the DHCP setting.  
• If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet  
Mask, and Gateway Address as needed.  
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on  
the remote control. To select a highlighted number, press Enter.  
52  
10. To prevent display of the IP address on the standby screen, turn off IP Address Display.  
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save  
your settings and exit the menus.  
Parent topic: Wired Network Projection  
Wireless Network Projection  
You can send images to your projector through a wireless network. To do this, you must install the  
Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless  
projection.  
Note: The wireless LAN module is not included with your projector.  
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,  
you can connect to the projector wirelessly using the EasyMP Network Projection software.  
There are two ways to connect the projector to your wireless network:  
• Using the optional Quick Wireless Connection USB Key (Windows only)  
• Configuring the connection manually using the projector's Network menus  
After installing the module and setting up the projector, install the network software from the Epson  
Projector Software CD or download the software, as necessary. Use the following software and  
documentation to set up, control, and monitor wireless projection:  
• EasyMP Network Projection software sets up your computer for wireless network projection. See the  
EasyMP Network Projection Operation Guide for instructions.  
• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the  
network. You can download the latest software and documentation from the Epson web site. Go to  
epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.  
• EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the  
computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guide for  
instructions.  
• EasyMP Network Updater software (Windows only) allows you to update firmware for a projector over  
a wired LAN. See the EasyMP Network Updater Operation Guide for instructions. You can download  
the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or  
epson.ca/support (Canada) and select your projector.  
• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app;  
visit epson.com/projectorapp (U.S.) or epson.ca/projectorapp (Canada) for more information.  
53  
 
Installing the Wireless LAN Module  
Using Quick Wireless Connection (Windows Only)  
Selecting Wireless Network Settings Manually  
Selecting Wireless Network Settings in Windows  
Selecting Wireless Network Settings in OS X  
Setting Up Wireless Network Security  
Parent topic: Using the Projector on a Network  
Related references  
Optional Equipment and Replacement Parts  
Projector Network Settings - Network Menu  
Installing the Wireless LAN Module  
To use the projector over a wireless network, install the optional Epson 802.11b/g/n wireless LAN  
module. Do not install any other type of wireless LAN module.  
Caution: Never remove the module while its indicator light is green or flashing, or while you are  
projecting wirelessly. You may damage the module or lose data.  
1. Turn off the projector and unplug the power cord.  
2. Remove the screw securing the wireless LAN module stopper.  
54  
 
3. Insert the wireless LAN module into the port.  
4. Attach the wireless LAN module stopper and secure it using the screw you removed.  
5. Plug in and turn on the projector.  
Parent topic: Wireless Network Projection  
55  
Using Quick Wireless Connection (Windows Only)  
You can use the Quick Wireless Connection USB Key to quickly connect the projector to a Windows  
computer wirelessly. Then you can project your presentation and remove the key when you are done.  
Note: The Quick Wireless Connection USB Key is not included with your projector.  
1. Turn on the projector.  
2. Connect the USB key to the projector's USB-A port.  
You see a projected message that the network information update is complete.  
3. Remove the USB key.  
4. Connect the USB key to a USB port on your computer or laptop.  
Note: In Windows Vista, if you see the AutoPlay window, select Run LaunchU3.exe, then select  
Allow on the next screen.  
5. Follow the on-screen instructions to install the Quick Wireless Connection driver.  
Note: If you see a Windows Firewall message, click Yes to disable the firewall.  
After a few minutes, your computer image is displayed by the projector. If it does not appear, press  
the LAN button on your remote control or restart your computer.  
6. Run your presentation as necessary.  
7. When you finish projecting wirelessly, select the Safely Remove Hardware option in the Windows  
taskbar, then remove the USB key from your computer.  
Note: You may need to restart your computer to reactivate your wireless LAN connection.  
Parent topic: Wireless Network Projection  
Selecting Wireless Network Settings Manually  
Before you can project from your wireless network, you must select the network settings for the projector  
using its menu system.  
1. Turn on the projector.  
2. Press the Menu button.  
56  
   
3. Select the Network menu and press Enter.  
4. Set the Wireless Mode setting to Wireless LAN On and press Enter.  
5. Select Network Configuration and press Enter.  
6. Select the Basic menu and press Enter.  
57  
7. Select the following basic options as necessary:  
• Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the  
projector over the network.  
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the  
PJLink protocol for projector control.  
• Web Control Password lets you enter a password up to 8 alphanumeric characters long for  
accessing the projector over the web. (Default user name is EPSONWEB; default password is  
admin.)  
• Projector Keyword lets you turn on a security password to prevent access to the projector by  
anyone not in the room with it. You must enter a displayed, randomized keyword from a computer  
using the EasyMP Network Projection software to access the projector.  
Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow  
buttons on the remote control to highlight characters and press Enter to select them.  
8. Select the Wireless LAN menu and press Enter.  
9. Select the settings on the Wireless LAN menu as necessary for your network.  
10. When you finish selecting settings, select Complete and follow the on-screen instructions to save  
your settings and exit the menus.  
After you complete the wireless settings for your projector, you need to select the wireless network on  
your computer.  
58  
Wireless LAN Menu Settings  
Parent topic: Wireless Network Projection  
Wireless LAN Menu Settings  
Setting  
Options  
Quick  
Description  
Connection Mode  
Selects the type of wireless  
connection:  
Advanced  
Quick: lets you quickly connect  
to one computer or use the  
optional Quick Wireless  
Connection USB key to connect  
Advanced: lets you connect to  
multiple computers via a wireless  
network access point  
Channel  
1ch  
6ch  
11ch  
On  
In Quick connection mode,  
selects the frequency band  
(channel) used by the wireless  
LAN  
SSID Auto Setting  
Turns on automatic SSID  
searching in Quick connection  
mode; set to Off when  
Off  
connecting to multiple projectors  
at the same time  
SSID  
Up 32 alphanumeric characters Sets the SSID (network name) of  
the wireless LAN system the  
projector is connecting to  
Search Access Point  
IP Settings  
—
Search for available wireless  
network access points in  
Advanced connection mode  
DHCP  
In Advanced connection mode,  
select DHCP if your network  
assigns addresses automatically,  
or manually enter the network's  
IP Address, Subnet Mask, and  
Gateway Address  
IP Address  
Subnet Mask  
Gateway Address  
59  
 
Setting  
Options  
On  
Description  
SSID Display  
Selects whether to display the  
SSID on the network standby  
screen  
Off  
IP Address Display  
On  
Off  
Selects whether to display the IP  
address on the network standby  
screen  
Parent topic: Selecting Wireless Network Settings Manually  
Selecting Wireless Network Settings in Windows  
Before connecting to the projector, select the correct wireless network on your computer.  
1. To access your wireless utility software, access the Desktop and double-click the network icon on  
the Windows taskbar.  
2. Do one of the following:  
• If your projector is set up on an existing network (Advanced mode), select the network name  
(SSID).  
• If your projector is configured for Quick mode, select the projector's SSID.  
3. Click Connect.  
Parent topic: Wireless Network Projection  
Selecting Wireless Network Settings in OS X  
Before connecting to the projector, select the correct wireless network in OS X.  
1. Click the AirPort icon on the menu bar at the top of the screen.  
2. Make sure AirPort is turned on, then do one of the following:  
• If your projector is set up on an existing network (Advanced mode), select the network name  
(SSID).  
• If your projector is configured for Quick mode, select the projector's SSID.  
Parent topic: Wireless Network Projection  
60  
   
Setting Up Wireless Network Security  
You can set up security for your projector to use on the wireless network. Set up one of the following  
security options to match the settings used on your network:  
• WPA/WPA2-PSK security (Advanced connection mode)  
• WPA2-PSK security (Advanced and Quick connection mode)  
Note: To use wireless network security in Quick connection mode, you must enable SSID Auto Setting.  
Check with your network administrator for guidance on entering the correct information.  
1. Press the Menu button.  
2. Select the Network menu and press Enter.  
3. Select Network Configuration and press Enter.  
4. Select the Security menu and press Enter.  
5. Select the security settings for your network.  
6. When you finish selecting settings, select Complete and follow the on-screen instructions to save  
your settings and exit the menus.  
Wireless Security Menu Settings  
Parent topic: Wireless Network Projection  
61  
 
Wireless Security Menu Settings  
Settings on the Security menu let you select the type of security and security settings that match the  
network you are connecting the projector to.  
Setting  
Options  
Description  
Security  
WPA2-PSK and WPA types  
available  
Selects the type of security used  
on the wireless network  
Passphrase  
Various keys from 8 to 32  
characters  
Selects the pre-shared key used  
on the network; passphrases are  
case-sensitive  
Parent topic: Setting Up Wireless Network Security  
Setting Up Projector Network E-Mail Alerts  
You can set up the projector to send you an e-mail alert over the network if there is a problem with the  
projector.  
1. Press the Menu button.  
2. Select the Network menu and press Enter.  
3. Select Network Configuration and press Enter.  
4. Select the Mail menu and press Enter.  
62  
   
5. Turn on Mail Notification.  
6. Enter the IP address for the SMTP Server option.  
Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a  
number from 0 to 255).  
7. Select a number for the SMTP server Port Number, from 1 to 65535 (default is 25).  
8. Choose an Address field, enter the e-mail address, and select the alerts you want to receive there.  
Repeat for up to three addresses.  
Note: Your e-mail address can be up to 32 alphanumeric characters long.  
9. When you finish selecting settings, select Complete and follow the on-screen instructions to save  
your settings and exit the menus.  
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.  
Network Projector E-mail Alert Messages  
Parent topic: Using the Projector on a Network  
Network Projector E-mail Alert Messages  
When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you  
receive an e-mail containing the following information:  
• Epson Projector on the subject line  
• The name of the projector experiencing a problem  
• The IP address of the affected projector  
• Detailed information about the problem  
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.  
Parent topic: Setting Up Projector Network E-Mail Alerts  
63  
 
Setting Up Monitoring Using SNMP  
Network administrators can install SNMP (Simple Network Management Protocol) software on network  
computers so they can monitor projectors. If your network uses this software, you can set up the  
projector for SNMP monitoring.  
1. Press the Menu button.  
2. Select the Network menu and press Enter.  
3. Select Network Configuration and press Enter.  
4. Select the Others menu and press Enter.  
5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field.  
Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a  
number from 0 to 255).  
6. If available, select the Priority Gateway setting for your network.  
7. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to  
allow the projector to be detected.  
8. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView  
setting to allow the projector to be detected.  
9. If you are connecting to a network using Bonjour, turn on the Bonjour setting.  
64  
 
10. If you want this projector to receive broadcasted messages over the network, turn on the Message  
Broadcasting setting. Administrators can broadcast messages over the network using the Message  
Broadcasting plug-in for EasyMP Monitor (Windows only).  
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save  
your settings and exit the menus.  
Parent topic: Using the Projector on a Network  
Controlling a Networked Projector Using a Web Browser  
Once you have connected your projector to your network, you can select projector settings and control  
projection using a compatible web browser. This lets you access the projector remotely.  
Note: The web setup and control features support Microsoft Internet Explorer 8.0 or later, and Safari on  
networks that do not use a proxy server for connection. You cannot select all of the projector menu  
settings or control all projector functions using a web browser.  
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings  
and control projection even if the projector is in standby mode.  
1. Make sure the projector is turned on.  
2. Start your web browser on a computer or device connected to the network.  
3. Type the projector's IP address into the browser's address box and press the computer's Enter key.  
You see the Web Control screen.  
Note: You may need to log in before you see the Web Control screen. If you see a log in window,  
enter your user name and password. (The default user name is EPSONWEB and the default  
password is admin.)  
4. To select projector menu settings, select the name of the menu and follow the on-screen  
instructions.  
5. To control projection remotely, select the Web Remote option.  
65  
 
You see a screen like this:  
1
2
3
4
5
6
7
8
9
Power button control  
Selects Computer port source  
Selects Video, S-Video, and HDMI port sources  
Freeze button control  
A/V Mute button control  
Page Up and Page Down button controls  
Searches for sources  
Selects the network source  
Selects the USB Display or USB device source  
10 Volume button controls  
11 Closed Caption control  
6. Select the icon corresponding to the projector function you want to control.  
Parent topic: Using the Projector on a Network  
66  
Related references  
Projector Setup Settings - Extended Menu  
Crestron RoomView Support  
If you are using the Crestron RoomView network monitoring and control system, you can set up your  
projector for use on the system. Crestron RoomView lets you control and monitor your projector using a  
web browser.  
Note: You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP  
Monitor when you use Crestron RoomView.  
For additional information on Crestron RoomView, contact Crestron.  
Setting Up Crestron RoomView Support  
Controlling a Networked Projector Using Crestron RoomView  
Parent topic: Using the Projector on a Network  
Setting Up Crestron RoomView Support  
To set up your projector for monitoring and control using a Crestron RoomView system, make sure your  
computer and projector are connected to the network. If you are connecting wirelessly, set up the  
projector using the Advanced network connection mode.  
Note: If you want to use the Crestron RoomView system when the projector is turned off, you need to  
adjust the Standby Mode settings in the ECO menu.  
1. Press the Menu button.  
2. Select the Network menu and press Enter.  
3. Select Network Configuration and press Enter.  
67  
   
4. Select the Others menu and press Enter.  
5. Set the setting to On to allow the projector to be detected.  
6. Turn off the projector, then turn it on again to enable the setting.  
Parent topic: Crestron RoomView Support  
Related references  
Projector Setup Settings - Extended Menu  
Controlling a Networked Projector Using Crestron RoomView  
Once you have set up your projector to use Crestron RoomView, you can control and monitor projection  
using a compatible web browser.  
1. Start your web browser on a computer connected to the network.  
2. Type the projector's IP address into the browser's address box and press the computer's Enter key.  
68  
 
You see this screen:  
3. Select the input source that you want to control in the Sources List box. You can scroll through  
available sources using the up and down arrows in the box.  
4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote  
control buttons. You can scroll through button options at the bottom of the screen.  
Note: These on-screen buttons do not directly correspond to the projector's remote control buttons:  
• OK acts as the Enter button  
• Menu displays the projector's menu  
5. To view information about the projector, click the Info tab.  
6. To change projector, Crestron, and password settings, click the Tools tab, select settings on the  
displayed screen, and click Send.  
7. When you finish selecting settings, click Exit to exit the program.  
Parent topic: Crestron RoomView Support  
69  
Using Basic Projector Features  
Follow the instructions in these sections to use your projector's basic features.  
Turning On the Projector  
Turning Off the Projector  
Selecting the Language for the Projector Menus  
Adjusting the Image Height  
Image Shape  
Resizing the Image with the Wide and Tele Buttons  
Focusing the Image Using the Focus Ring  
Remote Control Operation  
Selecting an Image Source  
Projection Modes  
Image Aspect Ratio  
Color Mode  
Controlling the Volume with the Volume Buttons  
Projecting a PC Free Presentation  
Turning On the Projector  
Turn on the computer or video equipment you want to use before you turn on the projector so it can  
display the image source.  
1. Connect the power cord to the projector's power inlet.  
70  
   
2. Plug the power cord into an electrical outlet.  
Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.  
The projector's power light turns blue. This indicates that the projector is receiving power.  
3. Press the power button on the projector or the remote control to turn on the projector.  
The projector beeps and the Status light flashes blue as the projector warms up. Once the projector  
is warmed up, the Status light stops flashing and turns blue.  
Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is  
especially dangerous for children.  
If you do not see a projected image right away, try the following:  
• Turn on the connected computer or video device.  
• Press the Source Search button on the projector or remote control to detect the video source.  
• Press the button for the video source on the remote control.  
Parent topic: Using Basic Projector Features  
Turning Off the Projector  
Before turning off the projector, shut down any computer connected to it so you can see the computer  
display during shutdown.  
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary  
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.  
Note: When using the A/V Mute feature, the projector lamp is still on. To turn off the lamp, turn off the  
projector.  
1. Press the power button on the projector or the remote control.  
71  
 
The projector displays a shutdown confirmation screen.  
2. Press the power button again. (To leave it on, press any other button.)  
The projector beeps twice, the lamp turns off, and the Status light turns off.  
Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the  
projector for transport right away (if necessary).  
3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.  
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status  
light is on or flashing.  
Parent topic: Using Basic Projector Features  
72  
Related references  
Projector Setup Settings - Extended Menu  
Selecting the Language for the Projector Menus  
If you want to view the projector's menus and messages in another language, you can change the  
Language setting.  
1. Turn on the projector.  
2. Press the Menu button.  
3. Select the Extended menu and press Enter.  
4. Select the Language setting and press Enter.  
5. Select the language you want to use and press Enter.  
6. Press Menu or Esc to exit the menus.  
Parent topic: Using Basic Projector Features  
Adjusting the Image Height  
If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust  
the image height using the projector's adjustable feet.  
1. Turn on the projector and display an image.  
73  
   
2. To adjust the front foot, pull up on the foot release lever and lift the front of the projector.  
The foot extends from the projector.  
3. Release the lever to lock the foot.  
4. If the image is tilted, rotate the rear feet to adjust their height.  
If the projected image is unevenly rectangular, you need to adjust the image shape.  
Parent topic: Using Basic Projector Features  
Related concepts  
Image Shape  
Related references  
Projector Feature Settings - Settings Menu  
74  
Image Shape  
You can project an evenly rectangular image by placing the projector directly in front of the center of the  
screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off  
to the side, you may need to correct the image shape for the best display quality.  
When you turn on automatic keystone correction in your projector's Settings menu, your projector  
automatically corrects vertical keystone effects when you reposition the projector.  
Note: When using interactive features, try not to make keystone corrections or use the Quick Corner  
setting. These features can affect interactive pen accuracy.  
Correcting Image Shape with the Horizontal Keystone Slider  
Correcting Image Shape with the Keystone Buttons  
Correcting Image Shape with Quick Corner  
Parent topic: Using Basic Projector Features  
Correcting Image Shape with the Horizontal Keystone Slider  
You can use the projector's horizontal keystone slider to correct the shape of an image that is unevenly  
rectangular horizontally, such as when the projector is placed to the side of the projection area.  
1. Turn on the projector and display an image.  
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.  
Note: You can also display the pattern by pressing the User button on the remote control (if the test  
pattern is assigned to this button).  
2. Adjust the slider until the image is evenly rectangular.  
75  
   
After correction, your image is slightly smaller.  
Parent topic: Image Shape  
Correcting Image Shape with the Keystone Buttons  
You can use the projector's keystone correction buttons to correct the shape of an image that is  
unevenly rectangular on the sides.  
Note: For interactive use, make sure the degree of horizontal and vertical keystone correction is no more  
than ± 3°.  
1. Turn on the projector and display an image.  
Note: You can also display the pattern by pressing the User button on the remote control (if the test  
pattern is assigned to this button).  
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment  
screen.  
76  
 
3. Press a keystone button on the projector's control panel to adjust the image shape.  
Note: The horizontal keystone adjustment buttons are labeled Wide and Tele.  
After correction, your image is slightly smaller.  
Note: If the projector is installed out of reach, you can also correct the image shape with the remote  
control using the Keystone settings in the projector menus.  
Parent topic: Image Shape  
77  
Related references  
Projector Feature Settings - Settings Menu  
Correcting Image Shape with Quick Corner  
You can use the projector's Quick Corner setting to correct the shape and size of an image that is  
unevenly rectangular on all sides.  
1. Turn on the projector and display an image.  
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.  
Note: You can also display the pattern by pressing the User button on the remote control (if the test  
pattern is assigned to this button).  
2. Press the Menu button.  
3. Select the Settings menu and press Enter.  
4. Select the Keystone setting and press Enter.  
5. Select the Quick Corner setting and press Enter. Then press Enter again.  
78  
 
You see the Quick Corner adjustment screen:  
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you  
want to adjust. Then press Enter.  
7. Press the arrow buttons to adjust the image shape as necessary.  
8. When you are finished, press Esc.  
Note: Using Quick Corner can affect the accuracy of the interactive pens.  
Parent topic: Image Shape  
Related references  
Projector Feature Settings - Settings Menu  
Resizing the Image with the Wide and Tele Buttons  
1. Turn on the projector and display an image.  
2. To enlarge the image size, press the Wide button on the projector's control panel.  
79  
 
3. To reduce the image size, press the Tele button.  
Note: If the projector is installed out of reach, you can also adjust the image size with the remote  
control using the Zoom setting in the projector menus.  
Parent topic: Using Basic Projector Features  
Related references  
Projector Feature Settings - Settings Menu  
Focusing the Image Using the Focus Ring  
1. Turn on the projector and display an image.  
2. To sharpen the image focus, rotate the projector’s focus ring.  
Parent topic: Using Basic Projector Features  
80  
 
Remote Control Operation  
The remote control lets you control the projector from almost anywhere in the room. You can point it at  
the screen, or the front or back of the projector.  
Make sure that you aim the remote control at the projector's receivers within the distance and angles  
listed here.  
1
2
3
19.7 feet (6 m)  
± 30°  
60°  
Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or  
the projector may not respond to commands. If you will not use the remote control for a long time,  
remove the batteries.  
Using the Remote Control as a Wireless Mouse  
Using the Remote Control as a Pointer  
Parent topic: Using Basic Projector Features  
81  
 
Using the Remote Control as a Wireless Mouse  
You can use the projector's remote control as a wireless mouse so you can control projection at a  
distance from the computer.  
1. Connect the projector to a computer using the projector's USB-B, Computer, or HDMI port to  
display video.  
2. If you connected your computer to a port other than the projector's USB-B port, also connect a USB  
cable to the projector's USB-B port and to a USB port on your computer (for wireless mouse  
support).  
3. Start your presentation.  
4. Use the following buttons on the remote control to control your presentation:  
• To move through slides or pages, press the up or down Page buttons.  
• To move the cursor on the screen, use the arrow buttons.  
• To left-click, press the  
button once (press it twice to double-click).  
• To right-click, press the Esc button.  
• To drag-and-drop, hold the  
at the destination.  
button as you move the cursor with the arrow buttons, then release  
Parent topic: Remote Control Operation  
Related tasks  
Connecting to a Computer for Pen Use or USB Mouse Control  
82  
 
Using the Remote Control as a Pointer  
You can use the projector's remote control as a pointer to help you call out important information on the  
screen. The default pointer shape is an arrow, but you can select an alternative shape using the Settings  
menu.  
1. Press the Pointer button on the remote control.  
2. Use the arrow buttons on the remote control to move the pointer on the screen.  
3. Press Esc to clear the pointer from the screen.  
Parent topic: Remote Control Operation  
Related references  
Projector Feature Settings - Settings Menu  
Selecting an Image Source  
If you connected multiple image sources to the projector, such as a computer and DVD player, you may  
want to switch from one image source to the other.  
1. Make sure the connected image source you want to use is turned on.  
2. For video image sources, insert a DVD or other video media and press its play button, if necessary.  
83  
   
3. Do one of the following:  
• Press the Source Search button on the projector or remote control until you see the image from  
the source you want.  
• Press the button for the source you want on the remote control. If there is more than one port for  
that source, press the button again to cycle through the sources.  
1
2
3
4
Computer port sources  
Video and HDMI sources  
USB port sources (computer display and external devices)  
Network source (LAN)  
84  
Parent topic: Using Basic Projector Features  
Projection Modes  
Depending on how you positioned the projector, you may need to change the projection mode so your  
images project correctly.  
• Front (default setting) lets you project from a table in front of the screen.  
• Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.  
• Rear flips the image horizontally to project from behind a translucent screen.  
• Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind  
a translucent screen.  
Changing the Projection Mode Using the Remote Control  
Changing the Projection Mode Using the Menus  
Parent topic: Using Basic Projector Features  
Changing the Projection Mode Using the Remote Control  
You can change the projection mode to flip the image over top-to-bottom.  
1. Turn on the projector and display an image.  
2. Hold down the A/V Mute button on the remote control for five seconds.  
The image disappears briefly and reappears flipped top-to-bottom.  
3. To change projection back to the original mode, hold down the A/V Mute button for five seconds  
again.  
Parent topic: Projection Modes  
85  
   
Changing the Projection Mode Using the Menus  
You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the  
projector menus.  
1. Turn on the projector and display an image.  
2. Press the Menu button.  
3. Select the Extended menu and press Enter.  
4. Select the Projection setting and press Enter.  
5. Select a projection mode and press Enter.  
6. Press Menu or Esc to exit the menus.  
Parent topic: Projection Modes  
Image Aspect Ratio  
The projector can display images in different width-to-height ratios called aspect ratios. Normally the  
input signal from your video source determines the image's aspect ratio. However, for certain images  
you can change the aspect ratio to fit your screen by pressing a button on the remote control.  
If you always want to use a particular aspect ratio for a certain video input source, you can select it using  
the projector's menus.  
Changing the Image Aspect Ratio  
Available Image Aspect Ratios  
86  
   
Parent topic: Using Basic Projector Features  
Related references  
Image Quality Settings - Image Menu  
Changing the Image Aspect Ratio  
You can change the aspect ratio of the displayed image to resize it.  
1. Turn on the projector and switch to the image source you want to use.  
2. Press the Aspect button on the remote control.  
The shape and size of the displayed image changes, and the name of the aspect ratio appears  
briefly on the screen.  
3. To cycle through the available aspect ratios for your input signal, press the Aspect button  
repeatedly.  
Parent topic: Image Aspect Ratio  
Available Image Aspect Ratios  
You can select the following image aspect ratios, depending on the input signal from your image source.  
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect  
ratio and resolution of your input signal.  
BrightLink 536Wi  
87  
   
Aspect ratio setting  
Auto  
Description  
Automatically sets the aspect ratio according to the input signal and  
the Resolution setting.  
Normal  
Displays images using the full projection area and maintains the  
aspect ratio of the image.  
16:9  
Full  
Converts the aspect ratio of the image to 16:9.  
Displays images using the full width of the projection area, but does  
not maintain the aspect ratio.  
Zoom  
Displays images using the full width of the projection area and  
maintains the aspect ratio of the image.  
Native  
Displays images as is (aspect ratio and resolution are maintained).  
Note: The Auto aspect ratio setting is available only for HDMI image sources.  
Aspect ratio setting  
Description  
4:3  
Displays images using the full projection area at 4:3 aspect ratio.  
Converts the aspect ratio of the image to 16:9.  
16:9  
Note: The Auto aspect ratio setting is available only for HDMI image sources.  
Parent topic: Image Aspect Ratio  
Color Mode  
The projector offers different Color Modes to provide optimum brightness, contrast, and color for a  
variety of viewing environments and image types. You can select a mode designed to match your image  
and environment, or experiment with the available modes.  
If you always want to use a particular color mode for a certain video input source, you can select it using  
the projector menus.  
Changing the Color Mode  
Available Color Modes  
Turning On Auto Iris  
Parent topic: Using Basic Projector Features  
88  
 
Related references  
Image Quality Settings - Image Menu  
Changing the Color Mode  
You can change the projector's Color Mode using the remote control to optimize the image for your  
viewing environment.  
1. Turn on the projector and switch to the image source you want to use.  
2. If you are projecting from a DVD player or other video source, insert a disc or other video media and  
press the play button, if necessary.  
3. Press the Color Mode button on the remote control to change the Color Mode.  
The image appearance changes and the name of the Color Mode appears briefly on the screen.  
4. To cycle through all the available Color Modes for your input signal, press the Color Mode button  
repeatedly.  
Parent topic: Color Mode  
Available Color Modes  
You can set the projector to use these Color Modes, depending on the input source you are using:  
Color Mode  
Dynamic  
Presentation  
Theatre  
Description  
Best for projecting in a bright room  
Best for color presentations in a bright room  
Best for movies projected in a dark room  
Best for standard sRGB computer displays  
sRGB  
89  
   
Color Mode  
Blackboard  
Description  
Best for presentations onto a green chalkboard (adjusts the colors  
accordingly)  
Parent topic: Color Mode  
Related references  
Image Quality Settings - Image Menu  
Turning On Auto Iris  
In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on  
the brightness of the content you project.  
1. Turn on the projector and switch to the image source you want to use.  
2. Press the Menu button.  
3. Select the Image menu and press Enter.  
4. Select the Auto Iris setting and choose one of the following:  
• High Speed to adjust brightness as soon as the scene changes.  
90  
 
• Normal for standard brightness adjustment.  
Note: You can set Auto Iris for each Color Mode that supports the feature. You cannot change the  
Auto Iris setting when you are using a Closed Caption setting.  
5. Press Menu or Esc to exit the menus.  
Parent topic: Color Mode  
Controlling the Volume with the Volume Buttons  
You can use the Volume buttons on the remote control to adjust the volume as you project a  
presentation with audio. The volume buttons control the projector’s internal speaker system or any  
external speakers you connected to the projector.  
You must adjust the volume separately for each connected input source.  
1. Turn on the projector and start a presentation that includes audio.  
2. To lower or raise the volume, press the Volume buttons on the remote control.  
A volume gauge appears on the screen.  
3. To set the volume to a specific level for an input source, use the projector menus.  
Parent topic: Using Basic Projector Features  
Projecting a PC Free Presentation  
You can use your projector's PC Free feature whenever you connect a USB device that contains  
compatible image or movie files. This lets you quickly and easily display and control them using the  
projector's remote control. You can also display a slide show of the images.  
Slideshow Features  
Supported PC Free File Types  
91  
   
Starting a Slide Show  
Starting a PC Free Movie Presentation  
Parent topic: Using Basic Projector Features  
Related concepts  
USB Device Projection  
Related tasks  
Connecting a USB Device or Camera to the Projector  
Slideshow Features  
Your projector's Slideshow feature lets you do the following:  
• Display individual images  
• Present a slide show of all images in a folder  
Parent topic: Projecting a PC Free Presentation  
Supported PC Free File Types  
You can project these types of files using the projector's PC Free feature.  
Note: For best results, place your files on media that is formatted in FAT16/32. If you have trouble  
projecting from media formatted for non-Windows file systems, try formatting the media for Windows  
instead. You may not be able to use the security features on certain USB storage devices with PC Free  
features.  
92  
   
File contents  
File type  
(extension)  
Details  
Image  
.jpg  
Make sure the file is not:  
• CMYK format  
• Progressive format  
• Highly compressed  
• Above 8192 × 8192 resolution  
Make sure the file resolution is not above 1280 × 800  
Make sure the file is not:  
.bmp  
.gif  
• Above 1280 × 800 resolution  
• Animated  
.png  
.avi  
Make sure the file resolution is not above 1280 × 800  
Make sure the file is not:  
Movie  
• Saved with an audio codec other than linear PCM or ADPCM  
• Above 1280 × 720 resolution  
• Larger than 2GB  
Parent topic: Projecting a PC Free Presentation  
Starting a Slide Show  
After connecting a USB device to the projector, you can switch to the USB input source and start your  
slide show.  
Note: You can change the Slideshow operation options or add special effects by highlighting Option at  
the bottom of the screen and pressing Enter.  
1. Press the USB button on the projector remote control.  
93  
 
The Slideshow screen appears.  
2. Do the following as necessary to locate your files:  
• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight  
the folder and press the Enter button.  
• To move back up a folder level on your device, highlight Back to Top and press Enter.  
• To view additional images in a folder, highlight Next page or Previous page, or press the Page  
up or down buttons on the remote control, and press Enter.  
3. Do one of the following to start your slide show:  
• To display an individual image, press the arrow buttons to highlight the image and press Enter.  
(Press the Esc button to return to the file list screen.)  
• To display a slide show of all the images in a folder, press the arrow buttons to highlight the  
Slideshow option at the bottom of the screen and press Enter.  
Note: If any file names are longer than 8 characters or include unsupported symbols, the file names  
may be shortened or changed only in the screen display.  
4. While projecting, use the following commands to control the display as necessary:  
• To rotate a displayed image, press the up or down arrow button.  
• To move to the next or previous image, press the left or right arrow button.  
5. To stop the display, follow the on-screen instructions or press the Esc button.  
94  
PC Free Display Options  
Parent topic: Projecting a PC Free Presentation  
PC Free Display Options  
You can select these display options when using the projector's PC Free feature.  
Setting  
Options  
Description  
Display Order  
Name Order  
Date Order  
In Ascending  
In Descending  
On  
Displays files in name order  
Displays files in date order  
Sort Order  
Sorts files in first-to-last order  
Sorts files in last-to-first order  
Displays a slide show continuously  
Displays a slide show one time through  
Does not display the next file automatically  
Continuous Play  
Off  
Screen Switching  
Time  
No  
1 Second to 60 Seconds  
Displays files for the selected time and  
switches to the next file automatically; high  
resolution images may switch at a slightly  
slower rate  
95  
 
Setting  
Effect  
Options  
Wipe  
Description  
Transitions between images with a wipe effect  
Dissolve  
Transitions between images with a dissolve  
effect  
Random  
Transitions between images using a random  
variety of effects  
Parent topic: Starting a Slide Show  
Starting a PC Free Movie Presentation  
After connecting a USB device or digital camera to the projector, you can switch to the USB input source  
and start your movie.  
Note: You can change the PC Free operation options by highlighting Option at the bottom of the screen  
and pressing Enter.  
1. Press the USB button on the projector remote control.  
The PC Free screen appears.  
96  
 
2. Do the following as necessary to locate your files:  
• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight  
the folder and press the Enter button.  
• To move back up a folder level on your device, highlight Back to Top and press Enter.  
• To view additional files in a folder, highlight Next page or Previous page and press Enter, or  
press the Page up or down buttons on the remote control.  
3. To play back a movie, press the arrow buttons to highlight the file and press Enter.  
Note: If any file names are longer than 8 characters or include unsupported symbols, the file names  
may be shortened or changed only in the screen display. If you want to play back all the movies in a  
folder in sequence, select the Slideshow option at the bottom of the screen.  
4. To stop movie playback, press the Esc button, highlight Exit, and press Enter.  
Parent topic: Projecting a PC Free Presentation  
97  
Adjusting Projector Features  
Follow the instructions in these sections to use your projector's feature adjustments.  
Shutting Off the Picture and Sound Temporarily  
Stopping Video Action Temporarily  
Zooming Into and Out of Images  
Projector Security Features  
Creating a User Pattern to Display  
Shutting Off the Picture and Sound Temporarily  
You can temporarily turn off the projected picture and sound if you want to redirect your audience's  
attention during a presentation. Any sound or video action continues to run, however, so you cannot  
resume projection at the point that you stopped it.  
If you want to display an image such as a company logo or picture when the presentation is stopped, you  
can set up this feature using the projector's menus.  
1. Press the A/V Mute button on the remote control or the projector to temporarily stop projection and  
mute any sound.  
2. To turn the picture and sound back on, press A/V Mute again.  
Parent topic: Adjusting Projector Features  
Stopping Video Action Temporarily  
You can temporarily stop the action in a video or computer presentation and keep the current image on  
the screen. Any sound or video action continues to run, however, so you cannot resume projection at the  
point that you stopped it.  
98  
     
Note: You can also stop video action using the interactive pens.  
1. Press the Freeze button on the remote control to stop the video action.  
2. To restart the video action in progress, press Freeze again.  
Parent topic: Adjusting Projector Features  
Zooming Into and Out of Images  
You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it  
on the screen.  
Note: You can also zoom into your image using the interactive pen.  
1. Press the E-Zoom + button on the remote control.  
You see a crosshair on the screen indicating the center of the zoom area.  
2. Use the following buttons on the remote control to adjust the zoomed image:  
• Use the arrow buttons to position the crosshair in the image area you want to zoom into.  
• Press the E-Zoom + button repeatedly to zoom into the image area, enlarging it as necessary.  
99  
 
• To pan around the zoomed image area, use the arrow buttons.  
• To zoom out of the image, press the E-Zoom – button as necessary.  
• To return to the original image size, press Esc.  
Parent topic: Adjusting Projector Features  
Projector Security Features  
You can secure your projector to deter theft or prevent unintended use by setting up the following  
security features:  
• Password security to prevent the projector from being turned on, and prevent changes to the startup  
screen and other settings.  
• Button lock security to block operation of the projector using the buttons on the control panel.  
• Security cabling to physically cable the projector in place.  
Password Security Types  
Locking the Projector's Buttons  
Installing a Security Cable  
Parent topic: Adjusting Projector Features  
Password Security Types  
You can set up these types of password security using one shared password:  
• Power On Protection password prevents anyone from using the projector without first entering a  
password.  
• User's Logo Protection password prevents anyone from changing the custom screen the projector  
can display when it turns on or when you use the A/V Mute feature. The presence of the custom  
screen discourages theft by identifying the projector’s owner.  
• Network Protection password prevents anyone from changing the network settings in the projector  
menus.  
Setting a Password  
Selecting Password Security Types  
Entering a Password to Use the Projector  
Saving a User's Logo Image to Display  
Parent topic: Projector Security Features  
100  
   
Setting a Password  
To use password security, you must set a password.  
1. Hold down the Freeze button on the remote control for about ten seconds or until you see this menu.  
2. Press the down arrow to select Password and press Enter.  
You see the prompt "Change the password?".  
3. Select Yes and press Enter.  
4. Press and hold down the Num button on the remote control and use the numeric buttons to set a  
four-digit password.  
The password displays as **** as you enter it. Then you see the confirmation prompt.  
5. Enter the password again.  
You see the message "Password accepted."  
101  
 
6. Press Esc to return to the menu.  
7. Make a note of the password and keep it in a safe place in case you forget it.  
Parent topic: Password Security Types  
Selecting Password Security Types  
After setting a password, you see this menu, allowing you to select the password security types you want  
to use.  
If you do not see this menu, hold down the Freeze button on the remote control for about 10 seconds or  
until the menu appears.  
1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On,  
press Enter again, and press Esc.  
2. To prevent changes to the User's Logo screen or related display settings, select User's Logo  
Protection, press Enter, select On, press Enter again, and press Esc.  
3. To prevent changes to network settings, select Network Protection, press Enter, select On, press  
Enter again, and press Esc.  
You can attach the Password Protect sticker to the projector as an additional theft deterrent.  
Note: Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the  
password required to use the projector.  
Parent topic: Password Security Types  
102  
 
Entering a Password to Use the Projector  
If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a  
password whenever you turn on the projector.  
You must enter the correct password to use the projector.  
1. Press and hold down the Num button on the remote control while you enter the password using the  
numeric buttons.  
The password screen closes.  
2. If the password is incorrect, the following may happen:  
• You see a "wrong password" message and a prompt to try again. Enter the correct password to  
proceed.  
103  
 
• If you enter an incorrect password several times in succession, the projector displays a request  
code and a message to contact Epson Support. Do not attempt to enter the password again.  
When you contact Epson Support, provide the displayed request code and proof of ownership for  
assistance in unlocking the projector.  
Parent topic: Password Security Types  
Related references  
Projector Setup Settings - Extended Menu  
Saving a User's Logo Image to Display  
You can transfer an image to the projector and then display it whenever the projector turns on. You can  
also display the image when the projector is not receiving an input signal or when you temporarily stop  
projection (using the A/V Mute feature). This transferred image is called the User's Logo screen.  
The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in  
identifying the projector's owner to help deter theft. You can prevent changes to the User's Logo by  
setting up password protection for it.  
1. Display the image you want to project as the User's Logo.  
2. Press the Menu button, select the Extended menu, and press Enter.  
3. Select the User's Logo setting and press Enter.  
You see a prompt asking if you want to use the displayed image as a user's logo.  
4. Select Yes and press Enter.  
104  
 
You see a selection box overlaying your image.  
5. Use the arrow buttons on the remote control to surround the image area you want to use as the  
User's Logo and press Enter.  
You see a prompt asking if you want to select this image area.  
6. Select Yes and press Enter. (If you want to change the selected area, select No, press Enter, and  
repeat the last step.)  
You see the User's Logo zoom factor menu.  
7. Select a zoom percentage and press Enter.  
You see a prompt asking if you want to save the image as the User's Logo.  
8. Select Yes and press Enter.  
You see a completion message.  
9. Press Esc to exit the message screen.  
10. Select the Extended menu and press Enter.  
11. Select Display and press Enter.  
12. Select when you want to display the User's Logo screen:  
• To display it whenever there is no input signal, select Display Background and set it to Logo.  
• To display it whenever you turn the projector on, select Startup Screen and set it to On.  
• To display it whenever you press the A/V Mute button, select A/V Mute and set it to Logo.  
To prevent anyone from changing the User's Logo settings without first entering a password, set a  
password and enable User's Logo security.  
Parent topic: Password Security Types  
105  
Related references  
Projector Setup Settings - Extended Menu  
Locking the Projector's Buttons  
You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You  
can lock all the buttons or all the buttons except the power button.  
1. Press the Menu button.  
2. Select the Settings menu and press Enter.  
3. Select the Control Panel Lock setting and press Enter.  
4. Select one of these lock types and press Enter:  
• To lock all of the projector's buttons, select Full Lock.  
• To lock all buttons except the power button, select Partial Lock.  
You see a confirmation prompt.  
5. Select Yes and press Enter.  
Unlocking the Projector's Buttons  
Parent topic: Projector Security Features  
Related references  
Projector Feature Settings - Settings Menu  
106  
 
Unlocking the Projector's Buttons  
If the projector's buttons have been locked, hold the Enter button on the projector's control panel for  
seven seconds to unlock them.  
Parent topic: Locking the Projector's Buttons  
Installing a Security Cable  
You can install two types of security cables on the projector to deter theft.  
• Use the security slot on the projector to attach a Kensington Microsaver Security system, available  
from Epson.  
• Use the security cable attachment point on the projector to attach a wire cable and secure it to a room  
fixture or heavy furniture.  
Note: Do not pass drop-prevention cables through the security cable attachment point when mounting  
the projector on a wall or ceiling.  
Parent topic: Projector Security Features  
Creating a User Pattern to Display  
You can transfer an image to the projector and then display it as a pattern to aid in presentations when  
you use the Pattern Display feature. This transferred image is called the User Pattern.  
1. Display the image you want to project as the User Pattern from a connected computer or video  
source.  
107  
     
2. Press the Menu button, select the Settings menu, and press Enter.  
3. Select the Pattern setting and press Enter.  
4. Select the User Pattern setting and press Enter.  
You see a prompt asking if you want to use the displayed image as a User Pattern.  
5. Select Yes and press Enter.  
Note: It takes a few moments for the projector to save the image; do not use the projector, its remote  
control, or any connected equipment until it is finished.  
You see a completion message.  
6. Press Esc to exit the message screen.  
Parent topic: Adjusting Projector Features  
Related references  
Projector Feature Settings - Settings Menu  
108  
Using the Interactive Features  
Follow the instructions in these sections to use your projector's interactive features.  
Interactive Modes  
Using the Interactive Pens  
Using BrightLink With a Computer  
Using BrightLink Without a Computer  
Interactive Modes  
The BrightLink interactive features turn any wall into an interactive whiteboard, either with or without a  
computer. These interactive modes are available:  
• In whiteboard mode, you can use one or both interactive pens to write on the projected "whiteboard".  
• In annotation mode (PC Free Annotation), you can annotate over content projected from a computer,  
tablet, document camera, or other source.  
• In PC Interactive mode, you can use the interactive pen as a mouse to navigate, select, and scroll  
through content from your computer.  
Note: You can also use the Easy Interactive Tools software to provide additional interactive features,  
such as saving your annotations and printing them. See the online Easy Interactive Tools Operation  
Guide for detailed instructions.  
Using the Projected Screen as a Whiteboard (Whiteboard Mode)  
Drawing on a Projected Image (PC Free Annotation Mode)  
Controlling Computer Features from a Projected Screen (PC Interactive Mode)  
Parent topic: Using the Interactive Features  
Using the Projected Screen as a Whiteboard (Whiteboard Mode)  
You can use the interactive pens to write or draw on the projection surface just as you would on a  
chalkboard or dry erase board. You can use either one or two pens at the same time.  
Note: Make sure you use two pens with different colored ends (blue and orange). You cannot use two  
pens of the same color simultaneously.  
109  
     
1. Make sure the Pen Mode option in the Easy Interactive Function menu is set to PC Free  
Interactive.  
2. Hover near or tap the board or projected image with the interactive pen. Tap the left or right arrow  
icon,  
3. Tap the  
whiteboard icon in the toolbar.  
You see the whiteboard screen, with the main toolbar on the side and the projection control toolbar  
on the bottom of the screen:  
4. To move the main toolbar to the other side of the screen, tap the  
the screen.  
arrow on the opposite side of  
Note: You can use the pen to move the arrow icon up or down to reposition the toolbar.  
5. To close the main toolbar, select the  
icon at the bottom of the toolbar.  
Note: If you want to hide the toolbar automatically after drawing, select the  
icon at the bottom of  
the toolbar (the icon will change shape).  
110  
6. To show or hide the projection control toolbar, select the  
arrow.  
Note: You can also show or hide the projection control toolbar from the projector's Display menu.  
Parent topic: Interactive Modes  
Drawing on a Projected Image (PC Free Annotation Mode)  
You can project from a computer, tablet, video device, or other source and add notes to your projected  
content using the interactive pens. You can use either one pen or both pens at the same time.  
Note: Make sure you use two pens with different colored ends (blue and orange). You cannot use two  
pens of the same color simultaneously.  
1. Make sure the Pen Mode option in the Easy Interactive Function menu is set to PC Free  
Interactive.  
2. Project an image from a connected device.  
3. Hover near or tap the board or projected image with the interactive pen. Tap the left or right arrow  
icon.  
4. Tap the  
annotation icon on the toolbar.  
111  
 
You see the main toolbar on the side and the projection control toolbar on the bottom of the  
projected image.  
5. To move the main toolbar to the other side of the screen, tap the  
the screen.  
arrow on the opposite side of  
Note: You can use the pen to move the arrow icon up or down to reposition the toolbar.  
6. To switch to one of the other interactive modes, do one of the following:  
• To switch to whiteboard mode, select the  
• To switch to PC Interactive mode, select  
Whiteboard tool.  
, then select  
.
Note: You can also press the Pen Mode button on the remote control to switch between modes.  
112  
7. To close the main toolbar, select the  
icon at the bottom of the toolbar.  
Note: If you want to hide the toolbar automatically after drawing, select the  
icon at the bottom of  
the toolbar (the icon will change shape).  
8. To show or hide the projection control toolbar, select the  
arrow.  
Parent topic: Interactive Modes  
Controlling Computer Features from a Projected Screen (PC Interactive Mode)  
You can navigate, select, and interact with your computer programs from the projected screen using the  
interactive pens just as you would a mouse.  
Note: OS X users need to install the Easy Interactive Driver before using PC Interactive mode. Go to  
epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.  
1. Connect the projector to your computer using a USB cable.  
2. Turn on your projector and project your computer screen.  
3. Press the Menu button on the remote control, select the Extended menu, and press the Enter  
button.  
113  
 
4. Select the USB Type B setting and press the Enter button.  
5. Select one of the following:  
• Easy Interactive Function to use PC Interactive mode.  
• USB Display/Easy Interactive Function to use PC Interactive mode and USB Display.  
• Wireless Mouse/USB Display to use the mouse and USB Display  
6. Press the Esc button to exit the USB Type B menu.  
7. Select the Easy Interactive Function setting and press the Enter button.  
114  
8. Select one of the following as the Pen Operation Mode:  
• Two Users/Mouse: Lets you use both interactive pens as a mouse with programs that support  
two pens  
• One User/Mouse: Lets you use one interactive pen as a mouse  
• One User/Pen: Uses the Windows pen and ink feature (Windows 8.x, Windows 7, and Windows  
Vista)  
9. Press the Enter button on the remote control and press the Menu button to exit the Extended menu.  
10. Hover near or tap on the board or the projected image with the interactive pen.  
The  
icon is displayed on the projected screen.  
11. Select the  
icon, then select the icon.  
You can now operate the computer using the interactive pens.  
PC Interactive Mode System Requirements  
Parent topic: Interactive Modes  
PC Interactive Mode System Requirements  
Your computer system must meet the system requirements here to use PC Interactive mode and Easy  
Interactive Tools.  
115  
 
Note: The Easy Interactive Driver must be installed and running to use Easy Interactive Tools on a Mac.  
Requirement  
Windows  
Mac  
Operating system  
Windows XP Professional, Home  
Edition, and Tablet PC Edition (32-bit);  
except for Service Pack 1  
OS X 10.5.8, 10.6.x, 10.7.x, 10.8.x,  
10.9.x, 10.10.x  
Windows Vista Ultimate, Enterprise,  
Business, Home Premium, and Home  
Basic (32-bit)  
Windows 8.x Pro, Enterprise, Windows 7  
Ultimate, Enterprise, Professional, Home  
Premium, and Home Basic (32- and 64-  
bit)  
CPU  
Intel Pentium M 1.6 GHz or faster (Core2 Power PC G4 1.5 GHz or faster  
Duo 1.2 GHz or faster recommended)  
(Core Duo 1.5 GHz or faster  
recommended)  
Memory  
512MB or more (1GB or more recommended)  
100MB or more  
Hard disk space  
Display  
Resolution between 1024 × 768 and 1920 × 1080, 16-bit color or greater  
Parent topic: Controlling Computer Features from a Projected Screen (PC Interactive Mode)  
Using the Interactive Pens  
Follow the instructions in these sections to use the interactive pens.  
Using the Pens  
Pen Calibration  
Parent topic: Using the Interactive Features  
Using the Pens  
Your projector came with an orange pen (Interactive Pen A), identified by the color on the end of the pen.  
You can purchase a second pen with a blue end (Interactive Pen B). You can use either pen, or both  
pens at the same time (one of each color), with Easy Interactive Tools. You can also purchase the  
Interactive Pen Extender to increase your reach with the pen.  
Make sure the pen batteries are installed.  
116  
   
Note: The pen turns off automatically after 20 minutes of inactivity. Tap the pen tip or press the button on  
the side to turn the pen back on.  
1
2
3
4
5
Pen tip  
Battery light  
Power/function button  
Attachment for optional strap or cord  
Battery cover  
• To turn on the pen, tap the pen tip or press the power/function button.  
Note: If you press the button, the battery light flashes briefly, then turns off. If the battery is low, the  
battery light flashes continuously.  
117  
• For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the  
black section near the tip of the pen.  
• To write or draw on the projection surface in annotation mode or whiteboard mode, do the following:  
• To select a projected item, such as an icon, tap the projection surface with the pen tip.  
• To draw on the projected screen, tap the projection surface with the pen and drag it as necessary.  
• To move the pointer, hover over the surface without touching it.  
118  
• To use the pen as a mouse in PC Interactive mode, select the  
icon and do the following:  
• To left-click, tap the board with the pen tip.  
• To double-click, tap twice.  
• To right-click, press the board with the pen for about 3 seconds.  
• To click and drag, tap and drag with the pen.  
• To move the cursor, hover over the board without touching it.  
Note: If you do not want to use the hovering feature, you can turn it off using the Easy Interactive  
Function setting in the projector's Extended menu.  
Parent topic: Using the Interactive Pens  
Pen Calibration  
Calibration coordinates the position of the pen with the location of your cursor. You only need to calibrate  
the first time you use your projector's interactive features. Calibration results remain until you calibrate  
again.  
If you notice positioning discrepancies after doing any of the following, calibrate again:  
• Performing Keystone correction  
• Using the Quick Corner feature  
• Adjusting the image size  
• Moving the projector  
Note: Move any pen you are not using away from the projection screen while calibrating.  
119  
 
Calibrating Automatically  
Calibrating Manually  
Parent topic: Using the Interactive Pens  
Calibrating Automatically  
You do not need the pens or a computer for Auto Calibration.  
Note: You can start Auto Calibration by pressing the User button on the remote control, by pressing and  
holding the A/V Mute button on the projector for three seconds, or by pressing the Menu button on the  
remote control as described here.  
1. Press the Menu button, select the Extended menu, and press Enter.  
120  
 
2. Select the Easy Interactive Function setting and press Enter.  
3. Select Auto Calibration and press Enter.  
4. Adjust the image focus, if necessary.  
5. Press Enter to select Yes.  
A pattern appears then disappears, and the system is calibrated. If you see a message that  
calibration failed, check for obstacles, disable the Quick Corner and Keystone settings, and retry  
the Auto Calibration. If you still see a message that calibration failed, you need to calibrate manually.  
121  
The cursor location and pen position should match after calibration. If not, you may need to calibrate  
manually.  
Parent topic: Pen Calibration  
Calibrating Manually  
If the cursor location and pen position do not match after auto calibration, you can calibrate manually.  
1. Press the Menu button, select the Extended menu, and press Enter.  
2. Select the Easy Interactive Function setting and press Enter.  
122  
 
3. Select Manual Calibration and press Enter.  
4. Adjust the image focus, if necessary.  
5. Press Enter to select Yes.  
A green circle appears in the upper left corner of your projected image.  
6. Touch the center of the circle with the tip of the pen.  
The circle disappears, and you see another circle below the first one.  
123  
Note: For the most accurate calibration, make sure you touch the center of the circle.  
7. Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next  
circle appears at the top of a new column.  
Note: Make sure you are not blocking the signal between the pen and the interactive receiver (next  
to the projection window on the projector).  
If you make a mistake, press the Esc button on the remote control to go back to the previous circle.  
To restart the calibration process, press and hold the Esc button for 2 seconds.  
8. Continue until all of the circles disappear.  
Parent topic: Pen Calibration  
124  
Using BrightLink With a Computer  
You can connect a computer to the projector and install the software from the CD labeled "Epson  
Projector Software for Easy Interactive Function" or you can install third party interactive software. You  
can then do the following:  
• Use the pens as a mouse to control your computer  
• Use the Easy Interactive Tools software to annotate with two pens at the same time  
Note: See the online Easy Interactive Tools Operation Guide for detailed information.  
• Save and print your annotations  
• Use the Tablet PC input panel in Windows 8.x, Windows 7, or Windows Vista  
• Use Ink Tools for annotation in Microsoft Office applications  
Adjusting the Pen Operation Area  
Easy Interactive Tools  
Windows Pen Input and Ink Tools  
Parent topic: Using the Interactive Features  
Adjusting the Pen Operation Area  
If you connect a different computer or adjust the computer's resolution, the pen operation area is  
adjusted automatically to match your mouse pointer position. If you notice that the pen position is  
incorrect when using PC Interactive mode, you can adjust the pen area manually.  
Note: Manual adjustment is not available when projecting from a LAN source.  
1. Project your computer's desktop.  
125  
   
2. Press the Menu button, select the Extended menu, and press Enter.  
3. Select the Easy Interactive Function setting and press Enter.  
4. Set the Pen Mode setting to PC Interactive.  
Note: You can also change this setting by pressing the Pen Mode button on the remote control.  
126  
5. Select Advanced in the PC Interactive section and press Enter.  
Note: Make sure the Auto Adjust Pen Area option is set to Off to prevent changes to your manual  
pen area adjustments.  
6. Select Manual Adj. Pen Area and press Enter.  
You see this screen:  
7. Press Enter to select Yes.  
The mouse pointer moves toward the top left corner.  
8. When the mouse pointer stops at the top left corner of the image, touch the tip of the pointer with the  
interactive pen.  
The mouse pointer moves toward the bottom right corner.  
127  
9. When the mouse pointer stops at the bottom right corner of the image, touch the tip of the pointer  
with the interactive pen.  
Parent topic: Using BrightLink With a Computer  
Easy Interactive Tools  
Your projector came with a CD containing the Easy Interactive Tools software for use with a computer.  
Easy Interactive Tools lets you use your interactive pen as a mouse to navigate, select, scroll, draw,  
save, and interact with projected content from your computer.  
These two modes are available:  
• Annotation (PC interactive) mode displays the toolbar on the projected image and lets you use the pen  
as a mouse to open applications, access links, and operate scroll bars, for example (using one pen at  
a time). You can also annotate whatever is displayed from your computer (using both pens at the  
same time).  
• Whiteboard mode lets you project on one of 3 solid colors or 6 background patterns, and use the  
toolbar to write or draw on the background. You can also import images from your computer or a  
document camera. In full screen whiteboard mode, two people can use the pens at the same time.  
Note: For detailed instructions on using the Easy Interactive Tools software, see the online Easy  
Interactive Tools Operation Guide or the online help.  
Parent topic: Using BrightLink With a Computer  
Windows Pen Input and Ink Tools  
If you are using Windows 8.x, Windows 7, or Windows Vista, you can use the pen input and Ink tools to  
add input and annotations to your work. You can also use these features over a network when you set  
the interactive features to be available on your network. See the EasyMP Network Projection Operation  
Guide for instructions on setting up your computer for network projection.  
Enabling Windows Pen Input and Ink Tools  
Using Windows Pen Input and Ink Tools  
Parent topic: Using BrightLink With a Computer  
Enabling Windows Pen Input and Ink Tools  
To use the pen input and Ink tools in Windows 8.x, Windows 7, or Windows Vista, you need to adjust the  
pen operation mode in your projector's menus.  
128  
     
1. Press the Menu button, select the Extended menu, and press Enter.  
2. Select the Easy Interactive Function setting and press Enter.  
3. Set the Pen Operation Mode setting in the PC Interactive section to One User/Pen and press  
Enter.  
Parent topic: Windows Pen Input and Ink Tools  
129  
Using Windows Pen Input and Ink Tools  
If you are using Windows 8.x, Windows 7, or Windows Vista, you can add handwritten input to your work  
and convert it to text.  
If you have Microsoft Office 2003 or later, you can also use the Ink function to add handwritten notes to a  
Word document, Excel spreadsheet, or PowerPoint presentation.  
Note: Option names for the annotation functions may vary depending on your version of Microsoft  
Office.  
• To open the Touch Keyboard in Windows 8.x, right-click or tap-and-hold on the Taskbar, and select  
Toolbars > Touch Keyboard. Select the keyboard icon on the screen and select the pen icon.  
• To open the Tablet PC input panel in Windows 7 or Windows Vista, select  
> All Programs >  
Accessories > Tablet PC > Tablet PC Input Panel.  
You can write in the box using the interactive pen or your finger, and select from a variety of options to  
edit and convert the text.  
• To add Ink annotations in Microsoft Office applications, select the Review menu, and select Start  
Inking.  
Note: In Microsoft Word or Excel, select the Insert tab and select Start Inking.  
130  
 
• To annotate your PowerPoint slides in Slideshow mode, press the button on the side of the interactive  
pen or press the projection surface with your finger for about 3 seconds, and select Pointer Options >  
Pen from the pop-up menu.  
Note: This also works in Windows XP Tablet PC Edition.  
For more information about these features, see Windows Help.  
Parent topic: Windows Pen Input and Ink Tools  
Using BrightLink Without a Computer  
You can use the pens to write or draw on the projection surface simultaneously without connecting a  
computer (PC Free annotation). This lets you annotate images from a document camera, iPad, DVD  
player, or other source.  
These two modes are available:  
• Annotation mode displays the built-in toolbar on whatever image is being projected from a document  
camera, iPad, or other source.  
• Whiteboard mode lets you project a white or black screen or one of 4 background patterns, and use  
the toolbar to write or draw as you would on a chalkboard or dry erase board.  
Using PC Free Annotation  
Built-in Tools for Use Without a Computer  
Using the Built-in Whiteboard Mode  
Changing Pen Width and Color Using the Built-in Toolbar  
Projector Control Toolbar  
Parent topic: Using the Interactive Features  
Using PC Free Annotation  
You can use a single pen with the built-in toolbar or two pens at the same time.  
Note: Make sure you use two pens with different colored ends (blue and orange). You cannot use two  
pens of the same color simultaneously.  
1. Make sure the Pen Mode option in the Easy Interactive Function menu is set to PC Free  
Interactive.  
2. Press one of the Source buttons on the remote control to select the source for the image you want  
to annotate. If you simply want to use a blank screen, select another unused source.  
131  
   
3. To activate the toolbar, tap the projection surface with the pen.  
You see arrow icons on the left and right side of the projected image.  
Note: The toolbar arrows disappear if they are not used. To make them reappear, tap the projection  
surface with the pen.  
4. To display the toolbar, select one of the  
arrows.  
Note: You can use the pen to move the arrows up or down.  
5. To close the toolbar, select the  
icon at the bottom of the toolbar.  
Note: If you want to hide the toolbar automatically after drawing, select the  
icon at the bottom of the  
toolbar (the icon will change shape).  
Parent topic: Using BrightLink Without a Computer  
Built-in Tools for Use Without a Computer  
The built-in toolbar is embedded in the projector and provides fewer functions than Easy Interactive  
Tools. For example, you cannot save your work with the built-in toolbar. If you want to save, connect a  
computer to the projector and use Easy Interactive Tools.  
132  
 
In the following illustration, the annotation mode tools are shown on the left, and the whiteboard mode  
tools on the right:  
Switch to annotation mode  
Switch to whiteboard mode  
Undo the last annotation  
Redo the last undo  
Select a white or black background or one of 4 patterns (whiteboard mode only)  
Change custom pen color and width  
Write or draw free-form lines with custom pen  
133  
Change highlighter pen color  
Write or draw free-form lines with transparent highlighter pen  
Black pen (fine point on left, thick on right)  
Red pen (fine point on left, thick on right)  
Blue pen (fine point on left, thick on right)  
Eraser (thin width on left, thick on right)  
Clear all annotations  
Hide the toolbar after each annotation  
Close the toolbar  
Parent topic: Using BrightLink Without a Computer  
Using the Built-in Whiteboard Mode  
In whiteboard mode, you can project a solid or patterned background, and then write or draw on it as you  
would on a chalkboard or dry erase board.  
1. Select the  
You see a white background.  
2. If you want to change the background, do the following:  
Whiteboard tool on the built-in toolbar.  
• Select the  
Background tool.  
• Select a black background or one of 4 different patterns.  
• Select the right arrow icon to close the selection window.  
134  
 
3. Do one of the following to write or draw on the background.  
• To erase, select the Eraser tool.  
• To clear the whole screen, select the  
Clear all tool.  
Parent topic: Using BrightLink Without a Computer  
Changing Pen Width and Color Using the Built-in Toolbar  
When you use the  
custom Pen or highlighter tools, you can select different colors and line widths.  
Note: You can also select the Black, Red, or Blue pen on the toolbar, and select the small circle on the  
left of the pen for a thin line, or the large circle on the right for a thick line.  
Note: When multiple users draw on the projected screen using multiple pens, you can select different  
colors and line widths for each pen.  
1. Select the  
arrow next to the  
custom Pen or  
Highlighter pen on the toolbar.  
2. Select the color and line width you want.  
3. Select the right arrow icon to close the selection window.  
Parent topic: Using BrightLink Without a Computer  
Projector Control Toolbar  
The projector control toolbar lets you control the projector with your pen from the projected screen just as  
you would using the remote control.  
If your network device is connected to the projector using EasyMP Multi PC Projection or Epson  
iProjection, you can also use the toolbar to select the network device from which you want to project.  
135  
   
Turn off the projector  
Change the image source using a displayed list.  
(To close the image source list, select the arrow icon at the bottom of the list.)  
Zoom into and out of the image  
Turn off the picture and sound  
Pause video action  
Decrease the volume  
Increase the volume  
Close the projector control toolbar  
Selecting Network Device Display from the Projector Control Toolbar  
Parent topic: Using BrightLink Without a Computer  
136  
Selecting Network Device Display from the Projector Control Toolbar  
If you have connected devices to the projector via a network, you can select to project an image from up  
to 50 of those devices using the projector control toolbar. You can select the image source from  
computers that are running EasyMP Multi PC Projection, and smartphones or tablets that are running  
Epson iProjection.  
1. Select the icon on the projector control toolbar.  
An image source list appears.  
2. Select the Participant List option.  
You see a list of available devices.  
137  
 
3. Select the user name for the device from which you want to project.  
The icon next to a user name indicates the currently selected source.  
Note: Select Refresh to update the user list.  
4. Select Return.  
You see the selected user's screen image.  
Parent topic: Projector Control Toolbar  
138  
Adjusting the Menu Settings  
Follow the instructions in these sections to access the projector menu system and change projector  
settings.  
Using the Projector's Menus  
Image Quality Settings - Image Menu  
Input Signal Settings - Signal Menu  
Projector Feature Settings - Settings Menu  
Projector Setup Settings - Extended Menu  
Projector Network Settings - Network Menu  
Projector Setup Settings - ECO Menu  
Projector Information Display - Info Menu  
Projector Reset Options - Reset Menu  
Using the Projector's Menus  
You can use the projector's menus to adjust the settings that control how your projector works. The  
projector displays the menus on the screen.  
139  
   
1. Press the Menu button on the control panel or remote control.  
You see the menu screen displaying the Image menu settings.  
140  
2. Press the up or down arrow button to move through the menus listed on the left. The settings for  
each menu are displayed on the right.  
Note: The available settings depend on the current input source.  
3. To change settings in the displayed menu, press Enter.  
4. Press the up or down arrow button to move through the settings.  
5. Change the settings using the buttons listed on the bottom of the menu screens.  
6. To return all the menu settings to their default values, select Reset.  
7. When you finish changing settings on a menu, press Esc.  
8. Press Menu or Esc to exit the menus.  
Parent topic: Adjusting the Menu Settings  
Image Quality Settings - Image Menu  
Settings on the Image menu let you adjust the quality of your image for the input source you are currently  
using. The available settings depend on the currently selected input source.  
To change settings for an input source, make sure the source is connected and select that source.  
141  
 
Setting  
Options  
Description  
Color Mode  
See the list of available Color  
Modes  
Adjusts the vividness of image  
colors for various image types  
and environments  
Brightness  
Contrast  
Varying levels available  
Varying levels available  
Varying levels available  
Varying levels available  
Varying levels available  
Lightens or darkens the overall  
image  
Adjusts the difference between  
light and dark areas of the image  
Color Saturation  
Tint  
Adjusts the intensity of the image  
colors  
Adjusts the balance of green to  
magenta tones in the image  
Sharpness  
Adjusts the sharpness or  
softness of image details  
Color Temp. (color temperature) Varying levels available  
Sets the overall color tone. Lower  
values tint the image red, and  
higher values tint the image blue.  
Color Adjustment  
Auto Iris  
Slider bars for each color  
Adjusts the intensity of individual  
hues in the image  
Normal  
High Speed  
Off  
Adjusts the projected luminance  
based on the image brightness  
when certain Color Modes are  
selected  
Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode,  
use the Power Consumption setting.  
Parent topic: Adjusting the Menu Settings  
Related references  
Available Color Modes  
142  
Input Signal Settings - Signal Menu  
Normally the projector detects and optimizes the input signal settings automatically. If you need to  
customize the settings, you can use the Signal menu. The available settings depend on the currently  
selected input source.  
Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the  
Auto button on the remote control.  
To change settings for an input source, make sure the source is connected and select that source.  
Setting  
Options  
Description  
Auto Setup  
On  
Automatically optimizes computer  
image quality (when On)  
Off  
Resolution  
Tracking  
Auto  
Sets the input signal resolution if  
not detected automatically using  
the Auto option  
Wide  
Normal  
Varying levels available  
Adjusts signal to eliminate vertical  
stripes in computer images  
143  
 
Setting  
Sync.  
Options  
Description  
Varying levels available  
Adjusts signal to eliminate  
fuzziness or flickering in  
computer images  
Position  
Up, down, left, right  
Adjusts the image location on the  
screen  
Progressive  
Off  
Sets whether to convert  
interlaced-to-progressive signals  
for certain video image types  
Video  
Film/Auto  
Off: for fast-moving video images  
Video: for most video images  
Film/Auto: for movies, computer  
graphics, and animation  
Noise Reduction  
Off  
Reduces flickering in analog  
images in two levels  
NR1  
NR2  
HDMI Video Range  
Auto  
Sets the video range to match the  
setting of the device connected to  
the HDMI input port  
Normal  
Expanded  
Auto: detects the video range  
automatically  
Normal: normally for images from  
a device other than a computer;  
can also be selected if the black  
areas of the image are too bright  
Expanded: normally for images  
from a computer; can also be  
selected if the image is too dark  
144  
Setting  
Options  
Auto  
Description  
Input Signal  
Specifies the signal type from  
input sources connected to  
computer ports  
RGB  
Component  
Auto: detects signals  
automatically  
RGB: corrects color for  
computer/RGB video inputs  
Component: corrects color for  
component video inputs  
Video Signal  
Auto  
Specifies the signal type from the  
input sources connected to the  
video ports  
Various video standards  
Auto: detects signals  
automatically  
Aspect  
See the list of available aspect  
ratios  
Sets the aspect ratio (width-to-  
height ratio) for the selected input  
source  
Overscan  
Auto  
Off  
Changes the projected image  
ratio to make the edges visible by  
a selectable percentage or  
automatically  
4%  
8%  
Image Processing  
Fine  
Fast  
Adjusts image processing  
speed/quality  
Parent topic: Adjusting the Menu Settings  
Related references  
Available Image Aspect Ratios  
Supported Video Display Formats  
145  
Projector Feature Settings - Settings Menu  
Options on the Settings menu let you customize various projector features.  
Setting  
Options  
Description  
Keystone  
H/V Keystone  
Quick Corner  
Adjusts image shape to  
rectangular (horizontally and  
vertically)  
H/V Keystone: lets you manually  
correct horizontal and vertical  
sides  
Quick Corner: select to correct  
image shape and alignment  
using an on-screen display  
Zoom  
Varying levels available  
Adjusts the size of the projected  
image  
146  
 
Setting  
Options  
Full Lock  
Partial Lock  
Off  
Description  
Control Panel Lock  
Controls projector button locking  
to secure the projector  
Full Lock: locks all buttons  
Partial Lock: locks all buttons  
except the power button  
Off: no buttons locked  
Pointer Shape  
Volume  
Three shapes available  
Varying levels available  
Changes the shape of the remote  
control pointer feature  
Adjusts the volume of projector’s  
speaker system or external  
speakers  
Mic Input Level  
Varying levels available  
Adjusts the volume of the  
projector's speaker system when  
you use a connected microphone  
Remote Receiver  
Front/Rear  
Front  
Limits reception of remote control  
signals by the selected receiver;  
Off turns off all receivers  
Rear  
Off  
User Button  
Power Consumption  
Info  
Assigns a menu option to the  
User button on the remote  
control for one-touch access  
Progressive  
Closed Caption  
Test Pattern  
Resolution  
Mic Input Level  
Pattern Display  
Auto Calibration  
Flip Horizontal  
147  
Setting  
Pattern  
Options  
Description  
Pattern Display  
Pattern Type  
User Pattern  
Test Pattern  
Selects various pattern display  
options  
Pattern Display: lets you display  
the selected pattern type on the  
screen to aid in presentation  
Pattern Type: selects the type of  
grid or line pattern to display  
User Pattern: captures a  
projected screen and saves it as  
a pattern for display  
Test Pattern: displays a test  
pattern to assist in focusing and  
zooming the image and  
correcting image shape  
Parent topic: Adjusting the Menu Settings  
Projector Setup Settings - Extended Menu  
Settings on the Extended menu let you customize various projector setup features that control its  
operation.  
148  
 
Easy Interactive Function Settings  
Setting  
Options  
Description  
General  
Auto Calibration  
Manual Calibration  
—
Auto Calibration and Manual  
Calibration: start calibration for  
pen operations  
Pen Mode  
Hovering  
PC Free Annotation  
Selects the mode for the  
interactive pens  
PC Interactive  
On  
Off  
Turns the pen hovering feature  
on and off; when set to On, the  
pointer follows the pen tip as you  
hover it over the screen and  
move it around  
Advanced  
Distance of Projectors  
Sync of Projectors  
Wired Sync Mode  
Confirm Clear Screen  
Color Palette  
Selects various settings for  
interactive features  
Distance of Projectors, Sync of  
Projectors, and Wired Sync  
Mode: let you adjust features for  
using multiple projectors of the  
same model in the same room  
Confirm Clear Screen: lets you  
display a confirmation screen  
before clearing all of the content  
Color Palette: lets you choose a  
different palette if certain colors  
are difficult to see  
PC Interactive  
149  
Setting  
Options  
Description  
Pen Operation Mode  
Two Users/Mouse  
One User/Mouse  
One User/Pen  
Selects the operating system  
version for pen operations  
One User/Mouse and Two  
Users/Mouse: let you to perform  
mouse operations using either  
one or two interactive pens  
One User/Pen: lets you use the  
pen input and Ink features on  
Windows Vista, Windows 7 and  
Windows 8.x  
Enable Right Click  
Advanced  
On  
Off  
Lets you use a long pen press as  
a right-click operation when using  
mouse mode; available only  
when Pen Operation Mode is  
set to One User/Mouse or Two  
Users/Mouse  
Pen Tip Button  
Let you select pen operation and  
adjustment options  
Auto Adjust Pen Area  
Manual Adj. Pen Area  
Pen Tip Button: assign either  
Right Click or Left Click to the  
pen tip button  
Select either Auto Adjust Pen  
Area or Manual Adj. Pen Area  
as the pen area adjustment  
option  
Note: To access the Manual Adj. Pen Area option, a computer must be connected to the USB-B port  
and the Pen Mode option must be set to PC Interactive.  
Other Extended Settings  
150  
Setting  
Display  
Options  
Description  
Messages  
Selects various display options  
Display Background  
Startup Screen  
A/V Mute  
Messages: controls whether  
messages are displayed on the  
screen  
Display Background: selects  
the screen color or logo to  
display when no signal is  
received  
Toolbars  
Pen Mode Icon  
Projector Control  
Startup Screen: controls  
whether a special screen  
appears when the projector starts  
up  
A/V Mute: selects the screen  
color or logo to display when A/V  
Mute is turned on  
Toolbars: controls whether the  
toolbars are always displayed in  
annotation mode  
Pen Mode Icon: controls the  
display and position of the pen  
icon in interactive computer  
mode  
Projector Control: controls  
where the projector control  
toolbar is displayed on the screen  
Closed Caption  
User's Logo  
Off  
Controls use of closed captions  
and selects the closed caption  
type (closed captions are only  
visible for NTSC signals  
connected through the S-Video  
or Video ports)  
CC1  
CC2  
–
Creates a screen that the  
projector displays to identify itself  
and enhance security  
151  
Setting  
Options  
Description  
Projection  
Front  
Selects the way the projector  
faces the screen so the image is  
oriented correctly  
Front/Ceiling  
Rear  
Rear/Ceiling  
Direct Power On  
High Altitude Mode  
Startup Source Search  
Auto Power On  
Operation  
Selects various operation options  
Direct Power On: lets you turn  
on the projector without pressing  
the power button  
High Altitude Mode: regulates  
the projector’s operating  
temperature at altitudes above  
4921 feet (1500 m)  
Startup Source Search:  
automatically detects the image  
signal that is input when the  
projector is turned on  
Auto Power On: lets you turn on  
the projector by turning on a  
computer connected to the  
Computer1 and Computer2  
ports  
152  
Setting  
Options  
Description  
A/V Settings  
A/V Output  
Selects the following when the  
projector is in standby mode  
(turned off):  
Audio Output  
HDMI Audio Output  
A/V Output: the Always On  
setting indicates that the  
projector outputs audio and video  
signals even while it is in standby  
mode; available only when  
Standby Mode is set to  
Communication On  
Audio Output: selects the audio  
input port when projecting  
images from the Computer1,  
Computer2, S-Video, Video,  
and USB-A ports  
HDMI Audio Output: selects  
which Audio port provides audio  
when viewing images from the  
HDMI port on the projector  
USB Type B  
Easy Interactive Function  
Selects what happens when you  
connect your computer to the  
projector's USB-B port  
USB Display/Easy Interactive  
Function  
Easy Interactive Function: lets  
you use the interactive pens with  
your computer  
Wireless Mouse/USB Display  
USB Display/Easy Interactive  
Function: lets you display your  
computer's image through the  
USB port and use the interactive  
pens with your computer  
Wireless Mouse/USB Display:  
lets you use the wireless mouse  
feature and display your  
computer's image through the  
USB port (interactivity not  
available)  
153  
Setting  
Options  
Description  
Language  
Various languages available  
Selects the language for  
projector menu and message  
displays (not changed by Reset  
option)  
Parent topic: Adjusting the Menu Settings  
Projector Network Settings - Network Menu  
Settings on the Network menu let you view network information and set up the projector for monitoring  
and control over a network.  
Setting  
Options  
Description  
Wireless Mode  
Wireless LAN On  
Off  
Turns wireless LAN features on  
and off  
154  
 
Setting  
Options  
Description  
Net. Info - Wireless LAN  
Connection mode  
Wireless LAN Sys.  
Antenna Level  
Projector Name  
SSID  
Displays wireless network status  
and details  
DHCP  
IP Address  
Subnet Mask  
Gateway Address  
MAC Address  
Region Code  
Projector Name  
DHCP  
Net. Info - Wired LAN  
Displays wired network status  
and details  
IP Address  
Subnet Mask  
Gateway Address  
MAC Address  
Network Configuration  
Accesses additional network  
menus  
Configures your network settings  
Parent topic: Adjusting the Menu Settings  
Related concepts  
Wired Network Projection  
Wireless Network Projection  
155  
Projector Setup Settings - ECO Menu  
Settings on the ECO menu let you customize projector functions to save power. When you select a  
power-saving setting, a leaf icon appears next to the menu item.  
Setting  
Options  
Normal  
ECO  
Description  
Power Consumption  
Selects the brightness mode of  
the projector lamp  
Normal: sets maximum lamp  
brightness  
ECO: reduces lamp brightness  
and fan noise, and saves power  
and lamp life  
Light Optimizer  
Sleep Mode  
On  
Off  
When Power Consumption is  
set to Normal and Auto Iris is  
turned off, the lamp brightness is  
adjusted based on the projected  
image; you can set this option for  
each color mode  
On  
Off  
Automatically places the  
projector in standby mode after  
an interval of inactivity  
156  
 
Setting  
Options  
Description  
Sleep Mode Timer  
A/V Mute Timer  
1 to 30 minutes  
Sets the interval for Sleep Mode  
On  
Off  
Automatically turns off the  
projector after 30 minutes if  
A/V Mute is enabled  
Standby Mode  
Communication On  
Communication Off  
Enable this setting to allow the  
following operations to occur  
when the projector is in standby  
mode:  
• Monitor and control the  
projector over a network  
• Output audio and video to an  
external device (A/V Output  
must be set to Always On)  
• Output audio from a  
microphone (A/V Output must  
be set to Always On)  
ECO Display  
On  
Off  
Displays a leaf icon in the bottom  
left corner of the projected screen  
to indicate the power-saving  
status when the lamp brightness  
changes  
Parent topic: Adjusting the Menu Settings  
157  
Projector Information Display - Info Menu  
You can display information about the projector and input sources by viewing the Info menu. However,  
you cannot change any settings in the menu.  
Select Version to display the projector's firmware version. Select Info to display the settings described  
below.  
Note: Available settings depend on the current input source. The lamp usage timer does not register any  
hours until you have used the lamp for at least 10 hours.  
Information item  
Lamp Hours  
Description  
Displays the number of hours (H) the lamp has been used in  
Normal and ECO Power Consumption modes; if the information is  
displayed in yellow, obtain a genuine Epson replacement lamp  
soon  
Source  
Displays the name of the port to which the current input source is  
connected  
Input Signal  
Resolution  
Video Signal  
Displays the input signal setting of the current input source  
Displays the resolution of the current input source  
Displays the video signal format of the current input source  
158  
 
Information item  
Refresh Rate  
Sync Info  
Description  
Displays the refresh rate of the current input source  
Displays information that may be needed by a service technician  
Status  
Displays information about projector problems that may be needed  
by a service technician  
Serial Number  
Event ID  
Displays the projector's serial number  
Displays the Event ID number corresponding to a specific projector  
problem; see the list of Event ID codes  
Event ID Code List  
Parent topic: Adjusting the Menu Settings  
Related references  
Projector Lamp Specifications  
Optional Equipment and Replacement Parts  
Event ID Code List  
If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the  
solution to the projector problem associated with the code.  
Event ID code  
0432  
Cause and solution  
The EasyMP Network Projection program did not start. Turn the projector off and  
then on again.  
0435  
0434  
Unstable network communication. Check the network communication status, wait a  
few moments, and try connecting to the network again.  
0482  
0484  
0485  
0433  
Cannot display the transferred images. Restart the EasyMP Network Projection  
program.  
0481  
Communication with computer was disconnected. Restart the EasyMP Network  
Projection program.  
159  
 
Event ID code  
0483  
Cause and solution  
The EasyMP Network Projection program quit unexpectedly. Check the network  
communication status, then turn the projector off and then on again.  
04FE  
0479  
A projector system error has occurred. Turn the projector off and then on again.  
04FF  
0891  
Cannot find an access point with the same SSID. Set your computer, access point,  
and projector to the same SSID.  
0892  
0893  
0894  
0898  
0899  
The WPA/WPA2 authentication type does not match. Make sure the wireless  
network security settings are correct.  
The WEP/TKIP/AES encryption type does not match. Make sure the wireless  
network security settings are correct.  
Communication with unauthorized access point was disconnected. Contact your  
network administrator.  
Failed to acquire DHCP address. Make sure the DHCP server is operating correctly.  
If you are not using DHCP, turn off the DHCP setting in the Network menus.  
A communication error has occurred. Try restarting the EasyMP Network Projection  
program and restarting your projector. If that does not solve the problem, contact  
Epson for help.  
Parent topic: Projector Information Display - Info Menu  
Projector Reset Options - Reset Menu  
You can reset most of the projector settings to their default values using the Reset All option on the  
Reset menu.  
160  
 
You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset  
Lamp Hours option.  
You cannot reset the following settings using the Reset All option:  
• Input Signal  
• User's Logo  
• Language  
• Network menu items  
• Lamp Hours  
• Password  
• Zoom  
Parent topic: Adjusting the Menu Settings  
161  
Maintaining and Transporting the Projector  
Follow the instructions in these sections to maintain your projector and transport it from place to place.  
Projector Maintenance  
Transporting the Projector  
Projector Maintenance  
Your projector needs little maintenance to keep working at its best.  
You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector  
from overheating due to blocked ventilation.  
The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part  
needs replacing, contact Epson or an authorized Epson servicer.  
Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never open  
any cover on the projector, except as specifically explained in this manual. Dangerous electrical voltages  
in the projector can injure you severely.  
Warning: Do not try to service this product yourself, except as specifically explained in this manual.  
Refer all other servicing to qualified servicers.  
Cleaning the Lens  
Cleaning the Projector Case  
Air Filter and Vent Maintenance  
Projector Lamp Maintenance  
Replacing the Remote Control Batteries  
Parent topic: Maintaining and Transporting the Projector  
Cleaning the Lens  
Clean the projector's lens periodically, or whenever you notice dust or smudges on the surface.  
• To remove dust or smudges, gently wipe the lens with a soft, lint-free cloth.  
162  
     
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the  
lens. Do not spray any liquid directly on the lens.  
Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the  
projector lamp may cause a fire.  
Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens  
to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue. Avoid  
touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface.  
Parent topic: Projector Maintenance  
Cleaning the Projector Case  
Before cleaning the projector case, turn off the projector and unplug the power cord.  
• To remove dust or dirt, use a soft, dry, lint-free cloth.  
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid  
directly on the projector.  
Caution: Do not use wax, alcohol, benzine, paint thinner, or other chemicals to clean the projector  
case. These can damage the case. Do not use canned air, or the gases may leave a residue.  
Parent topic: Projector Maintenance  
Air Filter and Vent Maintenance  
Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed  
with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance  
simple. Filter maintenance intervals will depend on the environment.  
If regular maintenance is not performed, your Epson projector will notify you when the temperature  
inside the projector has reached a high level. Do not wait until this warning appears to maintain your  
projector filter as prolonged exposure to high temperatures may reduce the life of your projector or lamp.  
Damage due to the failure to properly maintain the projector or its filter may not be covered by the  
projector or lamp Limited Warranties.  
Cleaning the Air Filter and Vents  
Replacing the Air Filter  
Parent topic: Projector Maintenance  
163  
   
Cleaning the Air Filter and Vents  
Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them.  
1. Turn off the projector and unplug the power cord.  
2. Place your finger into the groove at the top of the air filter cover and pull to open the cover.  
3. Pull the air filter out of the projector.  
164  
 
4. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.  
Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.  
5. Place the air filter back in the projector as shown.  
165  
6. Close the air filter cover.  
Parent topic: Air Filter and Vent Maintenance  
Replacing the Air Filter  
You need to replace the air filter in the following situations:  
• After cleaning the air filter, you see a message telling you to clean or replace it  
• The air filter is torn or damaged  
You can replace the air filter while the projector is mounted to the ceiling or placed on a table.  
1. Turn off the projector and unplug the power cord.  
166  
 
2. Place your finger into the groove at the top of the air filter cover and pull to open the cover.  
3. Pull the air filter out of the projector.  
Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to  
local regulations.  
167  
4. Place the new air filter in the projector as shown.  
5. Close the air filter cover.  
Parent topic: Air Filter and Vent Maintenance  
Related references  
Optional Equipment and Replacement Parts  
Projector Lamp Maintenance  
The projector keeps track of the number of hours the lamp is used and displays this information in the  
projector's menu system.  
Replace the lamp as soon as possible when the following occurs:  
• The projected image gets darker or starts to deteriorate  
• A message appears when you turn on the projector telling you to replace the lamp  
• The projector's lamp light is flashing orange and its power light is flashing blue  
Replacing the Lamp  
Resetting the Lamp Timer  
Parent topic: Projector Maintenance  
Related references  
Optional Equipment and Replacement Parts  
168  
 
Projector Lamp Specifications  
Projector Information Display - Info Menu  
Replacing the Lamp  
Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot.  
Warning: Let the lamp fully cool before replacing it to avoid injury.  
You can replace the lamp while the projector is mounted to the ceiling, if necessary.  
1. Turn off the projector and unplug the power cord.  
2. Allow the projector lamp to cool down for at least one hour.  
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp  
cover.  
Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful  
removing any broken glass to avoid injury. If the projector is installed on the ceiling, stand to the side  
of the lamp cover and not underneath it; pieces of glass could fall into your eyes or mouth when you  
open the lamp cover.  
169  
 
4. Slide the lamp cover out and lift it off.  
5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.  
170  
6. Grasp the raised section of the lamp and gently pull the lamp out of the projector.  
Note:  
The lamp(s) in this product contain mercury. Please consult your state and local  
regulations regarding disposal or recycling. Do not put in the trash.  
171  
7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right  
way.  
Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.  
172  
8. Push in the lamp firmly and tighten the screws to secure it.  
Caution: Do not over-tighten the screws.  
9. Replace the lamp cover and tighten the screw to secure it.  
173  
Note: Be sure the lamp cover is securely installed or the lamp will not come on.  
Reset the lamp timer to zero to keep track of the new lamp’s usage.  
Parent topic: Projector Lamp Maintenance  
Related tasks  
Resetting the Lamp Timer  
Resetting the Lamp Timer  
You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement  
message and to keep track of lamp usage correctly.  
Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage  
information.  
1. Turn on the projector.  
2. Press the Menu button.  
3. Select the Reset menu and press Enter.  
4. Select Reset Lamp Hours and press Enter.  
You see a prompt asking if you want to reset the lamp hours.  
5. Select Yes and press Enter.  
174  
 
6. Press Menu or Esc to exit the menus.  
Parent topic: Projector Lamp Maintenance  
Related references  
Projector Reset Options - Reset Menu  
Related tasks  
Replacing the Lamp  
Replacing the Remote Control Batteries  
The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they  
run out.  
Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,  
or mix new and old batteries.  
1. Remove the battery cover as shown.  
2. Remove the old batteries.  
Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on  
your hands. If it gets on your hands, wash them immediately to avoid injury.  
175  
 
3. Insert the batteries with the + and – ends facing as shown.  
4. Replace the battery cover and press it down until it clicks into place.  
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat  
or flame. Keep batteries out of the reach of children; they are choking hazards and are very  
dangerous if swallowed.  
Parent topic: Projector Maintenance  
Transporting the Projector  
The projector contains precision parts, some of which are glass. Follow these guidelines to transport,  
ship, or store the projector safely:  
• Remove any equipment connected to the projector.  
176  
 
• When transporting the projector a long distance or as checked luggage, pack it in a firm box with  
cushioning around it and mark the box "Fragile."  
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use  
equivalent materials with cushioning around the projector. Mark the box "Fragile."  
Note: Epson shall not be liable for any damages incurred during transportation.  
Parent topic: Maintaining and Transporting the Projector  
177  
Solving Problems  
Check the solutions in these sections if you have any problems using the projector.  
Projection Problem Tips  
Projector Light Status  
Using the Projector Help Displays  
Solving Image or Sound Problems  
Solving Projector or Remote Control Operation Problems  
Solving Interactive Problems  
Solving Network Problems  
Where to Get Help  
Projection Problem Tips  
If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it  
on.  
If this does not solve the problem, check the following:  
• The lights on the projector may indicate what the problem is.  
• The projector's Help system can display information about common problems, if the projector is  
operating.  
• The solutions in this manual can help you solve many problems.  
If none of these solutions help, you can contact Epson for technical support.  
Parent topic: Solving Problems  
178  
   
Projector Light Status  
The lights on the projector indicate the projector status and let you know when a problem occurs. Check  
the status and color of the lights and look for a solution in the table here.  
1
2
3
4
Power light  
Status light  
Lamp light  
Temp (temperature) light  
Power light  
Blue  
Status light  
Blue  
Lamp light Temp light  
Status and solution  
Off  
Off  
Off  
Off  
Normal operation.  
Blue  
Flashing blue  
Warming up. Wait for an image to  
appear.  
Blue  
Blue  
Off  
Off  
Off  
Off  
Off  
Standby or sleep mode.  
Flashing blue  
Shutting down. (When the Status light  
stops flashing, you can unplug the  
projector.)  
179  
 
Power light  
Status light  
Lamp light Temp light  
Status and solution  
Blue  
Varies  
Off  
Flashing  
orange  
Projector is too hot.  
• Make sure that the vents and air  
filter are not clogged with dust or  
obstructed by nearby objects.  
• Clean or replace the air filter.  
• Make sure the environmental  
temperature is not too hot.  
Off  
Flashing blue  
Off  
Orange  
Projector has overheated and turned  
off. Leave it turned off to cool down.  
After about five minutes, do the  
following:  
• Make sure that the vents and air  
filter are not clogged with dust or  
obstructed by nearby objects.  
• Clean or replace the air filter.  
• If operating the projector at high  
altitude, turn on High Altitude  
Mode.  
• If the problem persists, unplug the  
projector and contact Epson for  
help.  
Off  
Flashing blue  
Orange  
Off  
Lamp has a problem.  
• Check to see if the lamp is burned  
out, broken, or installed incorrectly.  
Reseat or replace the lamp as  
necessary.  
• Clean or replace the air filter.  
• If operating the projector at high  
altitude, turn on High Altitude  
Mode.  
• If the problem persists, unplug the  
projector and contact Epson for  
help.  
180  
Power light  
Status light  
Lamp light Temp light  
Status and solution  
Flashing blue  
Varies  
Flashing  
orange  
Varies  
Replace the lamp soon to avoid  
damage. Do not continue using the  
projector.  
Off  
Flashing blue  
Off  
Flashing  
orange  
A fan or sensor has a problem. Turn  
the projector off, unplug it, and  
contact Epson for help.  
Off  
Off  
Off  
Flashing blue  
Flashing blue  
Flashing blue  
Flashing  
orange  
Flashing  
orange  
Auto Iris error. Turn the projector off,  
unplug it, and contact Epson for help.  
Orange  
Orange  
Power error. Turn the projector off,  
unplug it, and contact Epson for help.  
Flashing  
orange  
Off  
Internal projector error. Turn the  
projector off, unplug it, and contact  
Epson for help.  
Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and  
contact Epson for help.  
Parent topic: Solving Problems  
Related references  
Where to Get Help  
Projector Setup Settings - Extended Menu  
Related tasks  
Cleaning the Air Filter and Vents  
Replacing the Air Filter  
Using the Projector Help Displays  
You can display information to help you solve common problems using the projector's Help system.  
1. Turn on the projector.  
2. Press the Help button on the projector or the remote control.  
You see the Help menu.  
3. Use the up and down arrow buttons to highlight the problem you want to solve.  
4. Press Enter to view the solutions.  
181  
 
5. When you are finished, do one of the following:  
• To select another problem to solve, press Esc.  
• To exit the help system, press Help.  
Parent topic: Solving Problems  
Solving Image or Sound Problems  
Check the solutions in these sections if you have any problems with projected images or sound.  
Solutions When No Image Appears  
Solutions When Image is Incorrect Using the USB Display Function  
Solutions When "No Signal" Message Appears  
Solutions When "Not Supported" Message Appears  
Solutions When Only a Partial Image Appears  
Solutions When the Image is Not Rectangular  
Solutions When the Image Contains Noise or Static  
Solutions When the Image is Fuzzy or Blurry  
Solutions When the Image Brightness or Colors are Incorrect  
Solutions to Sound Problems  
Solutions to Microphone Problems  
Parent topic: Solving Problems  
Solutions When No Image Appears  
If no image appears, try the following solutions:  
• Make sure the lens cover is open all the way or off.  
• Press the A/V Mute button on the remote control to see if the image was temporarily turned off.  
• Make sure all necessary cables are securely connected and the power is on for the projector and  
connected video sources.  
• Press the projector's power button to wake it from standby or sleep mode. Also see if your connected  
computer is in sleep mode or displaying a blank screen saver.  
• Check the settings on the Signal menu to make sure they are correct for the current video source.  
• Adjust the Brightness setting or select the Normal Power Consumption setting.  
• Check the Display setting to make sure Messages is set to On.  
182  
   
• If the projector does not respond when you press the control panel buttons, the buttons may be  
locked. Unlock the buttons.  
• If the projector does not respond when you press buttons on the remote control, make sure the remote  
receivers are turned on.  
• For images projected with Windows Media Center, reduce the screen size from full screen mode.  
• For images projected from applications using Windows DirectX, turn off DirectX functions.  
Parent topic: Solving Image or Sound Problems  
Related references  
Projector Setup Settings - Extended Menu  
Image Quality Settings - Image Menu  
Input Signal Settings - Signal Menu  
Projector Feature Settings - Settings Menu  
Related tasks  
Unlocking the Projector's Buttons  
Solutions When Image is Incorrect Using the USB Display Function  
If no image appears or if the image appears incorrectly using the USB Display function, try the following  
solutions:  
• Press the USB button on the remote control.  
• Make sure the USB Display software has installed correctly. Install it manually if necessary.  
• Make sure the USB Type B setting in the Extended menu is set to one of the USB Display options.  
• With OS X, select the USB Display icon in the Dock or from the Applications folder.  
• For images projected with Windows Media Center, reduce the screen size from full screen mode.  
• For images projected from applications using Windows DirectX, turn off DirectX functions.  
• If the mouse cursor flickers, select Make the movement of the mouse pointer smooth in the Epson  
USB Display Settings program on your computer (feature not available with Windows 2000).  
• Turn off the Transfer layered window setting in the Epson USB Display Settings program on your  
computer.  
• Make sure you are using the most recent version of the USB display software.  
Parent topic: Solving Image or Sound Problems  
183  
 
Solutions When "No Signal" Message Appears  
If the "No Signal" message appears, try the following solutions:  
• Press the Source Search button and wait a few seconds for an image to appear.  
• Turn on the connected computer or video source, and press its play button to begin your presentation,  
if necessary.  
• Check the connection from the projector to your video sources.  
• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.  
• If necessary, turn the projector and the connected computer or video source off and then on again.  
Displaying From a PC Laptop  
Displaying From a Mac Laptop  
Parent topic: Solving Image or Sound Problems  
Displaying From a PC Laptop  
If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to  
display on an external monitor.  
1. Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See  
your laptop manual for details.) Wait a few seconds for an image to appear.  
2. To display on both the laptop's monitor and the projector, try pressing the same keys again.  
3. If the same image is not displayed by the laptop and projector, check the Windows Display utility to  
make sure the external monitor port is enabled and extended desktop mode is disabled. (See your  
computer or Windows manual for instructions.)  
4. If necessary, check your video card settings and set the multiple display option to Mirror or  
Duplicate.  
Parent topic: Solutions When "No Signal" Message Appears  
Displaying From a Mac Laptop  
If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop  
for mirrored display. (See your laptop manual for details.)  
1. Open the System Preferences utility and select Displays.  
2. Click the Arrangement tab.  
3. Select the Mirror Displays checkbox.  
Parent topic: Solutions When "No Signal" Message Appears  
184  
     
Solutions When "Not Supported" Message Appears  
If the "Not Supported" message appears, try the following solutions:  
• Make sure the correct input signal is selected on the Signal menu.  
• Make sure the computer's display resolution does not exceed the projector's resolution and frequency  
limit. If necessary, select a different display resolution for your computer. (See your computer manual  
for details.)  
Parent topic: Solving Image or Sound Problems  
Solutions When Only a Partial Image Appears  
If only a partial computer image appears, try the following solutions:  
• Press the Auto button on the remote control to optimize the image signal.  
• Try adjusting the image position using the Position menu setting.  
• Press the Aspect button on the remote control to select a different image aspect ratio.  
• If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button until the  
projector returns to a full display.  
• Check the cables connecting the computer or video source to the projector. Try connecting different  
cables.  
• Check your computer display settings to disable dual display and set the resolution within the  
projector's limits. (See your computer manual for details.)  
• Check the resolution assigned to your presentation files to see if they are created for a different  
resolution than you are projecting in. (See your software help for details.)  
Parent topic: Solving Image or Sound Problems  
Related references  
Input Signal Settings - Signal Menu  
Supported Video Display Formats  
Solutions When the Image is Not Rectangular  
If the projected image is not evenly rectangular, try the following solutions:  
• If the projector is not mounted on the wall or ceiling, place it directly in front of the center of the screen,  
facing it squarely, if possible.  
• If you adjusted the projector height using the projector feet, press the keystone buttons on the  
projector to adjust the image shape.  
185  
     
• Adjust the Quick Corner or Keystone setting to correct the image shape.  
Note: Adjusting Quick Corner and Keystone settings may affect focus and pen calibration.  
Parent topic: Solving Image or Sound Problems  
Solutions When the Image Contains Noise or Static  
If the projected image seems to contain electronic interference (noise) or static, try the following  
solutions:  
• Check the cables connecting your computer or video source to the projector. They should be:  
• Separated from the power cord to prevent interference  
• Securely connected at both ends  
• Not connected to an extension cable  
• No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.3 m) for HDMI cables  
• Check the settings on the projector's Signal menu to make sure they match the video source. If  
available for your video source, adjust the Progressive and Noise Reduction settings.  
• Select a computer video resolution and refresh rate that are compatible with the projector.  
• If you are projecting from a computer, press the Auto button on the remote control to automatically  
adjust the tracking and sync. If the problem remains, display a uniformly patterned image on the  
screen and manually adjust the Tracking and Sync settings.  
• If you adjusted the image shape using the projector controls, try decreasing the Sharpness setting to  
improve image quality.  
• If you connected an extension power cable, try projecting without it to see if it caused interference in  
the signal.  
• If you are using the USB Display function, turn off the Transfer layered window setting in the Epson  
USB Display Settings program on your computer.  
Parent topic: Solving Image or Sound Problems  
Related references  
Input Signal Settings - Signal Menu  
Supported Video Display Formats  
Related tasks  
Displaying From a PC Laptop  
186  
 
Displaying From a Mac Laptop  
Solutions When the Image is Fuzzy or Blurry  
If the projected image is fuzzy or blurry, try the following solutions:  
• Adjust the image focus.  
• Clean the projector lens.  
• Position the projector close enough to the screen, and directly in front of it.  
• Position the projector so the keystone adjustment angle is not so wide that it distorts the image.  
• Adjust the Sharpness setting to improve image quality.  
• If you are projecting from a computer, press the Auto button on the remote control to automatically  
adjust the tracking and sync. If any bands or overall blurriness remain, display a uniformly patterned  
image on the screen and manually adjust the Tracking and Sync settings.  
• If you are projecting from a computer, use a lower resolution.  
• Turn off any keystone correction and disable the Quick Corner setting.  
Parent topic: Solving Image or Sound Problems  
Solutions When the Image Brightness or Colors are Incorrect  
If the projected image is too dark or light, or the colors are incorrect, try the following solutions:  
• Press the Color Mode button on the remote control to try different color modes for the image and  
environment.  
• Check your video source settings.  
• Adjust the available settings on the Image menu for the current input source, such as Brightness,  
Contrast, Tint, Color Adjustment, and/or Color Saturation.  
• Make sure you selected the correct Input Signal or Video Signal setting on the Signal menu, if  
available for your image source.  
• Make sure all the cables are securely connected to the projector and your video device. If you  
connected long cables, try connecting shorter cables.  
• If you are using the ECO Power Consumption setting, try selecting Normal in the projector's menus.  
Note: At high altitudes or locations subject to high temperatures, the image may become darker and  
you may not be able to adjust the Power Consumption setting.  
187  
   
• Position the projector close enough to the screen.  
• If the image has been progressively darkening, you may need to replace the projector lamp soon.  
Parent topic: Solving Image or Sound Problems  
Related concepts  
Projector Lamp Maintenance  
Related references  
Input Signal Settings - Signal Menu  
Image Quality Settings - Image Menu  
Projector Feature Settings - Settings Menu  
Solutions to Sound Problems  
If there is no sound when you expect it or the volume is too low or high, try the following solutions:  
• Adjust the projector's volume settings.  
• Press the A/V Mute button on the remote control to resume video and audio if they were temporarily  
stopped.  
• Press the Source Search button to switch to the correct input source, if necessary.  
• Check your computer or video source to make sure the volume is turned up and the audio output is set  
for the correct source.  
• Check the audio cable connections between the projector and your video source.  
• Make sure any connected audio cables are labeled "No Resistance".  
• If you are using the USB Display function, turn on the Output audio from the projector setting in the  
Epson USB Display Settings program on your computer.  
• If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac  
supports audio through the HDMI port. If not, you need to connect an audio cable.  
• If you want to use a connected audio source when the projector is off, set the Standby Mode option to  
Communication On and the A/V Output option to Always On.  
• Make sure the Audio Output option is set to the correct audio port for your video device.  
• If you turn the projector on immediately after turning it off, the cooling fans may run at high speed  
momentarily and cause an unexpected noise. This is normal.  
Parent topic: Solving Image or Sound Problems  
188  
 
Solutions to Microphone Problems  
If there is no sound when you use a microphone connected to the projector, try the following solutions:  
• Make sure the microphone is securely connected to the projector.  
• Make sure you are using a dynamic microphone, not a condenser microphone.  
• Adjust the Mic Input Level setting as necessary in the projector's menus.  
• If you want to use the microphone when the projector is off, set the Standby Mode option to  
Communication On and the A/V Output option to Always On.  
Parent topic: Solving Image or Sound Problems  
Related references  
Projector Feature Settings - Settings Menu  
Projector Setup Settings - Extended Menu  
Related tasks  
Connecting a Microphone  
Solving Projector or Remote Control Operation Problems  
Check the solutions in these sections if you have problems operating the projector or remote control.  
Solutions to Projector Power or Shut-Off Problems  
Solutions to Problems with the Remote Control  
Solutions to Password Problems  
Parent topic: Solving Problems  
Solutions to Projector Power or Shut-Off Problems  
If the projector does not come on when you press the power button or it shuts off unexpectedly, try the  
following solutions:  
• Make sure the power cord is securely connected to the projector and to a working electrical outlet.  
• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to  
turn on the projector.  
• The power cord may be defective. Disconnect the cord and contact Epson.  
• If the projector's lamp shuts off unexpectedly, it may have entered standby mode after a period of  
inactivity. Press the power button to wake the projector.  
189  
     
• If the projector's lamp shuts off and the power and Temp lights are red, the projector has overheated  
and shut off. Check the solutions for this light status.  
• If the power button on the remote control does not turn on the projector, check its batteries and make  
sure the Remote Receiver setting is turned on in the projector's menu, if available.  
Parent topic: Solving Projector or Remote Control Operation Problems  
Related references  
Projector Feature Settings - Settings Menu  
Projector Light Status  
Related tasks  
Unlocking the Projector's Buttons  
Solutions to Problems with the Remote Control  
If the projector does not respond to remote control commands, try the following solutions:  
• Check that the remote control batteries are installed correctly and have power. If necessary, replace  
the batteries.  
• Make sure you are operating the remote control within the reception angle and range of the projector.  
• Make sure the projector is not warming up or shutting down.  
• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release  
the button to wake the remote control up.  
• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the  
projector's remote receivers. Dim the lights or move the projector away from the sun or interfering  
equipment.  
• If available, turn off one of the remote receivers in the projector's menu system, or check if all the  
remote receivers were turned off.  
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to  
check or change the ID setting (feature not available with all projectors).  
• If you lose the remote control, you can order another one from Epson.  
Parent topic: Solving Projector or Remote Control Operation Problems  
Related references  
Projector Feature Settings - Settings Menu  
Optional Equipment and Replacement Parts  
Remote Control Operation  
190  
 
Solutions to Password Problems  
If you cannot enter or remember a password, try the following solutions:  
• You may have turned on password protection without first setting a password. Try entering 0000 using  
the remote control.  
• If you have entered an incorrect password too many times and see a message displaying a request  
code, write down the code and contact Epson. Do not attempt to enter the password again. Provide  
the request code and proof of ownership for assistance in unlocking the projector.  
• If you set a Web Control password and forgot the user ID or password, try entering the following:  
• User ID: EPSONWEB  
• Default password: admin  
• If you lose the remote control you cannot enter a password. Order a new one from Epson.  
Parent topic: Solving Projector or Remote Control Operation Problems  
Related tasks  
Controlling a Networked Projector Using a Web Browser  
Solving Interactive Problems  
Check the solutions in these sections if you have problems using the interactive system.  
Solutions When "Hardware Device Not Found" Message Appears  
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears  
Solutions When the Interactive Pens Do Not Work  
Solutions When Manual Calibration Does Not Work  
Solutions When the Built-In Toolbar (PC Free Annotation) Does Not Work  
Solutions When the Interactive Pen Position Is Not Accurate  
Solutions When the Interactive Pens Are Slow or Difficult to Use  
Solutions When the Interactive Pens Cause Interference or Unwanted Effects  
Parent topic: Solving Problems  
Solutions When "Hardware Device Not Found" Message Appears  
If the "Hardware device not found" message appears, try the following solutions:  
• Check the USB cable connection from the projector to your computer. Try disconnecting and then  
reconnecting the cable.  
191  
     
• If you are projecting from a laptop computer, make sure the battery has enough power, or connect the  
laptop to a power outlet.  
• If your USB cable is installed in the wall, try connecting a different USB cable to the projector and your  
computer.  
Parent topic: Solving Interactive Problems  
Related tasks  
Connecting to a Computer for Pen Use or USB Mouse Control  
Connecting to a Computer for USB Video and Audio  
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears  
If the "Error occurred in the Easy Interactive Function" message appears, contact Epson for help.  
Parent topic: Solving Interactive Problems  
Solutions When the Interactive Pens Do Not Work  
If the interactive pens do not work, try the following solutions:  
• The pens turn off automatically. Tap the pen tip or press the power/function button to turn the pen  
back on.  
• Make sure you are not covering the black section near the tip of the pen.  
• Make sure nothing is blocking the signal between the pen and the interactive pen receiver on the  
projector.  
• Try holding the pen at a different angle so that your hand is not blocking the signal.  
• Make sure the pen battery has enough power. Press the button on the side of the pen to check  
remaining battery power. Try replacing the battery.  
• If you are projecting from a computer, make sure the USB cable is connected to the computer and  
projector.  
• Dim the room lights and turn off any fluorescent lights. Make sure the projection surface and pen  
receiver are not in direct sunlight or other sources of bright lighting.  
• Remove any decorative lights from around the projector or projection surface.  
• If the pen tip is worn out or damaged, you may need to replace it.  
• Make sure the interactive pen receiver on the projector is clean and free from dust.  
• Make sure there is no interference from infrared remote controls, mice, or infrared microphones.  
192  
   
• Make sure the USB Type B option on the Extended menu is set to Easy Interactive Function or USB  
Display/Easy Interactive Function.  
• Make sure you have calibrated the system. Try recalibrating.  
• Make sure the Pen Mode and Pen Operation Mode settings are set correctly in the Easy Interactive  
Function options on the Extended menu.  
Parent topic: Solving Interactive Problems  
Related concepts  
Pen Calibration  
Related references  
Optional Equipment and Replacement Parts  
Projector Setup Settings - Extended Menu  
Related tasks  
Installing Batteries in the Pen  
Connecting to a Computer for Pen Use or USB Mouse Control  
Connecting to a Computer for USB Video and Audio  
Using the Pens  
Solutions When Manual Calibration Does Not Work  
If you are having trouble calibrating manually, try the following solutions:  
• If the circle does not move to the next position, or it moves automatically, dim or turn off any bright  
lights near the projection surface.  
• Make sure the projector is not too close to the projection surface.  
• Select Reset All from the Reset menu to restore the projector settings to their default values.  
Parent topic: Solving Interactive Problems  
Related references  
Projector Reset Options - Reset Menu  
Solutions When the Built-In Toolbar (PC Free Annotation) Does Not Work  
If you cannot use the pen without a computer, try the following solutions:  
• Press one of the Source buttons on the remote control to select the source for the image you want to  
annotate. To use a blank screen, select Computer2 or another unused source.  
• Make sure you have calibrated the system. Try recalibrating.  
193  
   
• Press the Pen Mode button on the remote control to toggle between PC Interactive and PC Free  
Annotation modes.  
Parent topic: Solving Interactive Problems  
Related concepts  
Pen Calibration  
Related references  
Projector Setup Settings - Extended Menu  
Solutions When the Interactive Pen Position Is Not Accurate  
If the pen position is not the same as the mouse pointer, try the following solutions:  
• Make sure you have calibrated the system. Try manual calibration.  
• Try adjusting the pen operation area.  
• If you use the E-Zoom + button on the remote control to enlarge the image, the pen position is not  
accurate. When you return the image to the original size, the position should be correct.  
• In PC Interactive mode (in the Extended menu), turn off Auto Adjust Pen Area and select Manual  
Adj. Pen Area.  
• Try changing the computer's resolution to 1280 × 800.  
• Select Reset All from the Reset menu to restore the projector settings to their default values.  
Parent topic: Solving Interactive Problems  
Related concepts  
Pen Calibration  
Related references  
Projector Reset Options - Reset Menu  
Projector Setup Settings - Extended Menu  
Related tasks  
Adjusting the Pen Operation Area  
Solutions When the Interactive Pens Are Slow or Difficult to Use  
If the pens are difficult to use or respond too slowly, try the following solutions:  
• For easier operation, hold the pen perpendicular to the projection surface.  
194  
   
• For the best performance, connect your computer to the projector using a VGA or HDMI cable for  
display and the USB cable for interactivity.  
• If you are using a computer, try setting your computer's display to 1280 × 800.  
• If you are using USB Display in Windows, you may need to disable Windows Aero in the Epson USB  
Display Settings program on your computer.  
• If you are having difficulty double-clicking in OS X, go to the System Preferences menu, select  
Mouse or Trackpad, and reduce the Double-Click Speed.  
• If you are projecting over a network, see the EasyMP Network Projection Operation Guide for  
performance adjustment instructions.  
Parent topic: Solving Interactive Problems  
Solutions When the Interactive Pens Cause Interference or Unwanted Effects  
If the pens are causing interference or unwanted effects, try the following solutions:  
• When two pens are used at the same time, make sure they are approximately 4 inches (10.16 cm)  
apart.  
• Do not rest the pens on the image area of an interactive table, to avoid interference with your  
computer's mouse.  
• Make sure that nothing is blocking the direct line to the infrared site.  
Parent topic: Solving Interactive Problems  
Solving Network Problems  
Check the solutions in these sections if you have problems using the projector on a network.  
Solutions When Network Alert E-Mails are Not Received  
Solutions When You Cannot Access the Projector Through the Web  
Parent topic: Solving Problems  
Solutions When Network Alert E-Mails are Not Received  
If you do not receive an e-mail alerting you to problems with a projector over the network, try the  
following solutions:  
• Make sure the projector is turned on and connected to the network correctly. (If an error shut down the  
projector, it cannot send an e-mail.)  
195  
     
• Make sure you set up the projector e-mail alert settings correctly on the projector's network Mail menu  
or in the network software.  
• Set the Standby Mode setting to Communication On so the network software can monitor the  
projector in standby mode.  
Parent topic: Solving Network Problems  
Related concepts  
Wired Network Projection  
Wireless Network Projection  
Related references  
Projector Setup Settings - Extended Menu  
Projector Network Settings - Network Menu  
Solutions When You Cannot Access the Projector Through the Web  
If you are unable to access the projector through a web browser, make sure you are using the correct ID  
and password, which are case sensitive.  
• For the user ID, enter EPSONWEB. (You cannot change the user ID.)  
• For the password, enter the password set in the projector's Network menu. The default password is  
admin.  
• Make sure you have access to the network the projector is on.  
Note: The user ID and password are case sensitive.  
Parent topic: Solving Network Problems  
Related tasks  
Controlling a Networked Projector Using a Web Browser  
Where to Get Help  
If you need to contact Epson for technical support services, use the following support options.  
Internet Support  
Visit Epson's support website at epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to  
common problems with your projector. You can download utilities and documentation, get FAQs and  
troubleshooting advice, or e-mail Epson with your questions.  
196  
   
Speak to a Support Representative  
To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the  
duration of your warranty period. You may also speak with a projector support specialist by dialing (562)  
276-4394 (U.S.) or (905) 709-3839 (Canada).  
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time,  
Saturday.  
Days and hours of support are subject to change without notice. Toll or long distance charges may  
apply.  
Before you call, have the following information ready:  
• Product name  
• Product serial number (located on the bottom or rear of the projector, or in the menu system)  
• Proof of purchase (such as a store receipt) and date of purchase  
• Computer or video configuration  
• Description of the problem  
Purchase Supplies and Accessories  
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized  
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online  
at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).  
To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer  
referral in Canada).  
Parent topic: Solving Problems  
197  
Technical Specifications  
These sections list the technical specifications of your projector.  
General Projector Specifications  
Projector Lamp Specifications  
Remote Control Specifications  
Projector Dimension Specifications  
Projector Electrical Specifications  
Projector Environmental Specifications  
Projector Safety and Approvals Specifications  
Supported Video Display Formats  
USB Display System Requirements  
General Projector Specifications  
Type of display  
Resolution  
Lens  
Poly-silicon TFT active matrix  
1280 × 800 pixels (WXGA)  
F=1.60  
Focal length: 6.4 mm  
Color reproduction  
Brightness  
Full color, up to 1 billion colors  
Normal Power Consumption mode:  
White light output 3400 lumens (ISO 21118 standard)  
Color light output 3400 lumens  
ECO Power Consumption mode:  
White light output 1900 lumens (ISO 21118 standard)  
Note: Color brightness (color light output) and white brightness  
(white light output) will vary depending on usage conditions. Color  
light output measured in accordance with IDMS 15.4; white light  
output measured in accordance with ISO 21118.  
Contrast ratio  
16000:1 with Dynamic Color Mode, Normal Power Consumption  
mode, Wide Zoom setting, and Auto Iris on  
198  
   
Image size  
39 inches (0.99 m) to 116 inches (2.95 m)  
21.3 inches (0.54 m) to 48 inches (1.22 m)  
(in native aspect ratio)  
Projection distance  
(in native aspect ratio)  
Projection methods  
Optical aspect ratio  
(width-to-height)  
Front, rear, ceiling-mounted  
16:10  
Focus adjustment  
Zoom adjustment  
Zoom ratio  
Manual  
Digital  
1.0 to 1.35  
(Tele-to-Wide)  
Internal sound system  
Noise level  
16 W monaural  
37 dB (Normal Power Consumption mode)  
29 dB (ECO Power Consumption mode)  
± 7º vertical; Auto Keystone correction  
± 5º horizontal keystone  
Keystone correction angle  
USB Type B port compatibility USB 1.1 and 2.0 compliant for USB display, external mouse control,  
firmware update, interactive functions, or copying menu settings  
USB Type A port compatibility One USB 1.1 and 2.0 compliant port for USB device input, Epson  
document camera display, wireless LAN, firmware update, or  
copying menu settings  
Parent topic: Technical Specifications  
Projector Lamp Specifications  
Type  
Power consumption  
UHE (Ultra High Efficiency)  
215 W  
199  
 
Lamp life  
Normal Power Consumption mode:  
Up to about 5000 hours  
ECO Power Consumption mode:  
Up to about 10000 hours  
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary  
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.  
Parent topic: Technical Specifications  
Remote Control Specifications  
Reception range  
Batteries  
19.7 feet (6 m)  
Two alkaline or manganese AA  
Parent topic: Technical Specifications  
Projector Dimension Specifications  
Height (excluding feet)  
3.7 inches (94 mm)  
Width  
Depth  
Weight  
13.5 inches (344 mm)  
12.4 inches (314.5 mm)  
8.5 lb (3.9 kg)  
Parent topic: Technical Specifications  
Projector Electrical Specifications  
Rated frequency  
Power supply  
50/60 Hz  
100 to 240 VAC ±10%  
3.2 to 1.4 A  
200  
     
Power consumption  
Operating:  
(100 to 120 V)  
Normal Power Consumption mode: 315 W  
ECO Power Consumption mode: 230 W  
Standby:  
1.90 W (Networked Standby), 0.22 W (Energy Saving)  
Operating:  
Power consumption  
(220 to 240 V)  
Normal Power Consumption mode: 298 W  
ECO Power Consumption mode: 221 W  
Standby:  
2.10 W (Networked Standby), 0.28 W (Energy Saving)  
Parent topic: Technical Specifications  
Projector Environmental Specifications  
Temperature  
Operating:  
Up to 7500 ft (2286 m): 41 to 95 °F (5 to 35 °C)  
7500 ft (2286 m) to 9843 ft (3000 m): 41 to 86 °F (5 to 30 °C)  
Storage: 14 to 140 °F (–10 to 60 °C)  
Operating: 20 to 80%  
Humidity (relative, non-  
condensing)  
Storage: 10 to 90%  
Operating altitude  
Up to 4921 feet (1500 m)  
4921 feet (1500 m) to 9843 feet (3000 m) with High Altitude Mode  
enabled  
Parent topic: Technical Specifications  
Projector Safety and Approvals Specifications  
United States  
FCC Part 15 Class B (DoC)  
UL60950-1 2nd edition (cTUVus Mark)  
201  
   
Canada  
ICES-003 Class B  
CSA C22.2 No. 60950-1-07  
Parent topic: Technical Specifications  
Supported Video Display Formats  
For best results, your computer's monitor port or video card resolution should be set to display in the  
projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other  
computer display resolutions, so your image will be resized to fit automatically.  
Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the  
projector. (See your computer or video card manual for details.)  
The table here lists the compatible refresh rate and resolution for each compatible video display format.  
Display format  
Refresh rate (in Hz)  
Resolution (in pixels)  
Computer signals (analog RGB)  
VGA  
60/72/75/85  
56/60/72/75/85  
60/72/75/85  
60  
640 × 480  
SVGA  
XGA  
800 × 600  
1024 × 768  
1280 × 768  
1366 × 768  
1280 × 800  
1440 × 900  
1600 × 900  
1152 × 864  
1280 × 1024  
1280 × 960  
1400 × 1050  
1680 × 1050  
1600 × 1200  
640 × 480  
WXGA  
60  
60/75/85  
60/75/85  
60  
WXGA+  
WXGA++  
SXGA  
70/75/85  
60/75/85  
60/75/85  
60/75  
SXGA+  
WSXGA+*  
UXGA  
60  
60  
MAC13"  
67  
202  
 
Display format  
MAC16"  
Refresh rate (in Hz)  
Resolution (in pixels)  
832 × 624  
75  
75  
59  
75  
MAC19"  
1024 × 768  
1024 × 768  
MAC21"  
1152 × 870  
Composite video  
TV (NTSC)  
TV (SECAM)  
TV (PAL)  
60  
720 × 480  
720 × 576  
720 × 576  
50  
50/60  
Component video  
SDTV (480i)  
SDTV (576i)  
SDTV (480p)  
SDTV (576p)  
HDTV (720p)  
HDTV (1080i)  
HDMI input signals  
VGA  
60  
720 × 480  
720 × 576  
720 × 480  
720 × 576  
1280 × 720  
1920 × 1080  
50  
60  
50  
50/60  
50/60  
60  
60  
60  
60  
60  
60  
60  
60  
60  
60  
640 × 480  
SVGA  
800 × 600  
XGA  
1024 × 768  
1280 × 800  
1366 × 768  
1440 × 900  
1600 × 900  
1680 × 1050  
1280 × 960  
1280 × 1024  
WXGA  
WXGA+  
WXGA++  
WSXGA+  
SXGA  
203  
Display format  
SXGA+  
Refresh rate (in Hz)  
Resolution (in pixels)  
1400 × 1050  
1600 × 1200  
720 × 480  
60  
UXGA  
60  
SDTV (480i/480p)  
SDTV (576i/576p)  
HDTV (720p)  
HDTV (1080i)  
HDTV (1080p)  
60  
50  
720 × 576  
50/60  
50/60  
24/30/50/60  
1280 × 720  
1920 × 1080  
1920 × 1080  
* Wide resolution only  
Parent topic: Technical Specifications  
USB Display System Requirements  
Your computer system must meet the system requirements here to use the projector's USB Display  
software.  
Requirement  
Windows  
Mac  
Operating system  
Windows 2000 (Service Pack 4 only)  
Mac OS X 10.5.x (32-bit), and  
10.6.x, 10.7.x , 10.8.x, 10.9.x,  
10.10.x (32- and 64-bit)  
Windows XP Professional, Home  
Edition, and Tablet PC Edition (32-bit)  
Windows Vista Ultimate, Enterprise,  
Business, Home Premium, and Home  
Basic (32-bit)  
Windows 7 Ultimate, Enterprise,  
Professional, and Home Premium (32-  
and 64-bit); Home Basic and Starter (32-  
bit)  
Windows 8.x, Pro, and Enterprise (32-  
and 64-bit)  
USB version  
USB 1.1 and above (USB 2.0 recommended)  
204  
 
Requirement  
Windows  
Mac  
CPU  
Mobile Pentium III 1.2 GHz or faster  
(1.6 GHz or faster recommended)  
Power PC G4 1 GHz or faster (Core  
Duo 1.83 GHz or faster  
recommended)  
Memory  
256MB or more (512MB or more  
recommended)  
512MB or more  
Hard disk space  
Display  
20MB or more  
Resolution between 640 × 480 and  
1920 × 1200, 16-bit color or greater  
Resolution between 640 × 480 and  
1680 × 1200, 16-bit color or greater  
Parent topic: Technical Specifications  
205  
Notices  
Check these sections for important notices about your projector.  
Recycling  
Important Safety Information  
Important Safety Instructions  
FCC Compliance Statement  
Trademarks  
Open Source Software License  
Copyright Notice  
Recycling  
Epson offers a recycling program for end of life products. Please go to this site for information on how to  
return your products for proper disposal.  
Parent topic: Notices  
Important Safety Information  
Caution: Never look into the projector lens when the lamp is turned on; the bright light can damage your  
eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except  
the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.  
Except as specifically explained in this User's Guide, do not attempt to service this product yourself.  
Refer all servicing to qualified service personnel.  
Warning: The projector and its accessories come packaged in plastic bags. Keep plastic bags away  
from small children to avoid any risk of suffocation.  
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible  
residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new  
lamp.  
Parent topic: Notices  
206  
     
Important Safety Instructions  
Follow these safety instructions when setting up and using the projector:  
• Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid  
standing in front of the projector so the bright light does not shine into your eyes.  
• Do not place the projector on an unstable cart, stand, or table.  
• Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 7°  
forward or back.  
• If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using  
mounting hardware designed for use with this projector.  
• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from  
loosening and do not use oils or lubricants. This may cause the projector case to crack and the  
projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and  
could damage the projector.  
• Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of  
magnetic fields.  
• Use the type of power source indicated on the projector. Use of a different power source may result in  
fire or electric shock. If you are not sure of the power available, consult your dealer or power company.  
• Place the projector near a wall outlet where the plug can be easily unplugged.  
• Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not  
insert the plug into a dusty outlet. Insert the plug firmly into the outlet. Do not pull the power cord when  
disconnecting the plug; always be sure to hold the plug when disconnecting it. Do not overload wall  
outlets, extension cords, or power strips. Failure to comply with these precautions could result in fire or  
electric shock.  
• Do not place the projector where the cord can be walked on. This may result in fraying or damage to  
the plug.  
• Unplug the projector from the wall outlet before cleaning. Use a dry cloth (or, for stubborn dirt or  
stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol cleaners, any  
sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.  
• Do not block the slots and openings in the projector case. They provide ventilation and prevent the  
projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it  
on top of loose papers. Do not cover the projector with a blanket, curtain, or tablecloth. If you are  
setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and  
the air exhaust vent.  
• Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.  
207  
 
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially  
flammable objects, near the projector. Never spill liquid of any kind into the projector.  
• If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the  
projectors to allow for proper ventilation.  
• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed  
to cool the projector. Do not use canned air, or the gases may leave a residue.  
• Do not store the projector outdoors for an extended length of time.  
• Except as specifically explained in this manual, do not attempt to service this product yourself. Refer  
all servicing to qualified personnel. Opening or removing covers may expose you to dangerous  
voltages and other hazards.  
• Never open any covers on the projector except as specifically explained in this manual. Never attempt  
to disassemble or modify the projector. Refer all repairs to qualified service personnel.  
• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the  
following conditions: if it does not operate normally when you follow the operating instructions, or  
exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the  
projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the  
projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been  
damaged.  
• Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.  
• Unplug the projector when it will not be used for extended periods.  
• Do not use the projector where it may be exposed to rain, water, or excessive humidity.  
• Do not use or store the projector where it may be exposed to smoke, steam, corrosive gases,  
excessive dust, vibration, or shock.  
• Do not use the projector where flammable or explosive gases may be present.  
• Do not use or store the projector or remote control in a hot location, such as near a heater, in direct  
sunlight, or in a closed vehicle.  
• If you use the projector in a country other than where you purchased it, use the correct power cord for  
that country.  
• Do not stand on the projector or place heavy objects on it.  
• Do not use the projector outside of the required temperature range of 41 to 95 °F (5 to 35 °C) at an  
altitude of 7500 feet (2286 m) or less, or 41 to 86 °F (5 to 30 °C) at a higher altitude. Doing so may  
cause an unstable display and could lead to projector damage. Do not use or store the projector where  
it may be exposed to sudden changes in temperature.  
208  
• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or  
in direct sunlight for long periods of time. Doing so may cause damage to the case.  
• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not  
bring your hands or face close to the vents while projection is in progress. Do not bring your face close  
to the projector while it is in use.  
• Before you move the projector, make sure its power is turned off, the plug is disconnected from the  
outlet, and all cables are disconnected.  
• Never try to remove the lamp immediately after use because it will be extremely hot. Before removing  
the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely.  
• Do not disassemble the lamp or subject it to impacts.  
• Do not place the source of an open flame, such as a lit candle, on or near the projector.  
• Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or  
pull it excessively. Keep the power cord away from hot electrical appliances.  
• If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or  
coming in contact with your eyes or mouth. If you do inhale gases or gases come in contact with your  
eyes or mouth, seek medical advice immediately.  
• If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from  
falling into your eyes or mouth when you open the lamp cover. If pieces of glass do get into your eyes  
or mouth, seek medical advice immediately.  
Note:  
The lamp(s) in this product contain mercury. Please consult your state and local regulations  
regarding disposal or recycling. Do not put in the trash.  
WARNING: The cords included with this product contain chemicals, including lead, known to the State of  
California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is  
provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.)  
Restriction of Use  
Parent topic: Notices  
Restriction of Use  
When this product is used for applications requiring high reliability/safety such as transportation devices  
related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or  
functional/precision devices, you should use this product only after giving consideration to including fail-  
safes and redundancies into your design to maintain safety and total system reliability.  
209  
 
Because this product was not intended for use in applications requiring extremely high reliability/safety  
such as aerospace equipment, main communication equipment, nuclear power control equipment, or  
medical equipment related to direct medical care, please make your own judgment on this product's  
suitability after a full evaluation.  
Parent topic: Important Safety Instructions  
FCC Compliance Statement  
For United States Users  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause interference to radio and television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
WARNING  
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC  
Certification or Declaration of this device and may cause interference levels which exceed the limits  
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded  
equipment interface cable with this device. If this equipment has more than one interface connector, do  
not leave cables connected to unused interfaces. Changes or modifications not expressly approved by  
the manufacturer could void the user’s authority to operate the equipment.  
For Canadian Users  
CAN ICES-3(B)/NMB-3(B)  
Parent topic: Notices  
210  
 
Trademarks  
EPSON®, EasyMP®, Instant Off®, PowerLite®, and Quick Corner® are registered trademarks, and EPSON  
Exceed Your Vision is a registered logomark of Seiko Epson Corporation.  
Accolade® and PrivateLine® are registered trademarks, and Extra CareSM is a service mark of Epson  
America, Inc.  
Mac, OS X and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.  
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI  
Licensing LLC.  
General Notice: Other product names used herein are for identification purposes only and may be  
trademarks of their respective owners. Epson disclaims any and all rights in those marks.  
Parent topic: Notices  
Open Source Software License  
GNU GPL  
This projector product includes the open source software programs which apply the GNU General Public  
License Version 2 or later version ("GPL Programs").  
We provide the source code of the GPL Programs until five (5) years after the discontinuation of same  
model of this projector product.  
If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's  
Guide.  
These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public  
License for more details.  
The list of GPL Programs is as follows and the names of author are described in the source code of the  
GPL Programs  
The list of GPL Programs  
busybox-1.13.4  
211  
   
iptables-1.4.4  
libgcc1(gcc-4.3.3)  
libstdc++-6.0.10  
linux-2.6.27  
patches  
udhcp 0.9.8  
uvc rev.219  
wireless_tools 29  
EPSON original drivers  
The GNU General Public License Version 2 is as follows. You also can see the GNU General Public  
License Version 2 at http://www.gnu.org/licenses/.  
GNU GENERAL PUBLIC LICENSE  
Version 2, June 1991  
Copyright (c) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  
02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document,  
but changing it is not allowed.  
Preamble  
The licenses for most software are designed to take away your freedom to share and change it. By  
contrast, the GNU General Public License is intended to guarantee your freedom to share and change  
free software--to make sure the software is free for all its users. This General Public License applies to  
most of the Free Software Foundation's software and to any other program whose authors commit to  
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public  
License instead.) You can apply it to your programs, too.  
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are  
designed to make sure that you have the freedom to distribute copies of free software (and charge for  
this service if you wish), that you receive source code or can get it if you want it, that you can change the  
software or use pieces of it in new free programs; and that you know you can do these things.  
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask  
you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute  
copies of the software, or if you modify it.  
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the  
recipients all the rights that you have. You must make sure that they, too, receive or can get the source  
code. And you must show them these terms so they know their rights.  
212  
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which  
gives you legal permission to copy, distribute and/or modify the software.  
Also, for each author's protection and ours, we want to make certain that everyone understands that  
there is no warranty for this free software. If the software is modified by someone else and passed on,  
we want its recipients to know that what they have is not the original, so that any problems introduced by  
others will not reflect on the original authors' reputations.  
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that  
redistributors of a free program will individually obtain patent licenses, in effect making the program  
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free  
use or not licensed at all.  
The precise terms and conditions for copying, distribution and modification follow.  
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND  
MODIFICATION  
0. This License applies to any program or other work which contains a notice placed by the copyright  
holder saying it may be distributed under the terms of this General Public License. The "Program",  
below, refers to any such program or work, and a "work based on the Program" means either the  
Program or any derivative work under copyright law: that is to say, a work containing the Program or a  
portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter,  
translation is included without limitation in the term "modification".) Each licensee is addressed as "you".  
Activities other than copying, distribution and modification are not covered by this License; they are  
outside its scope. The act of running the Program is not restricted, and the output from the Program is  
covered only if its contents constitute a work based on the Program (independent of having been made  
by running the Program). Whether that is true depends on what the Program does.  
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any  
medium, provided that you conspicuously and appropriately publish on each copy an appropriate  
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the  
absence of any warranty; and give any other recipients of the Program a copy of this License along with  
the Program.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer  
warranty protection in exchange for a fee.  
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on  
the Program, and copy and distribute such modifications or work under the terms of Section 1 above,  
provided that you also meet all of these conditions:  
a) You must cause the modified files to carry prominent notices stating that you changed the files and the  
date of any change.  
213  
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived  
from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the  
terms of this License.  
c) If the modified program normally reads commands interactively when run, you must cause it, when  
started running for such interactive use in the most ordinary way, to print or display an announcement  
including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you  
provide a warranty) and that users may redistribute the program under these conditions, and telling the  
user how to view a copy of this License. (Exception: if the Program itself is interactive but does not  
normally print such an announcement, your work based on the Program is not required to print an  
announcement.)  
These requirements apply to the modified work as a whole. If identifiable sections of that work are not  
derived from the Program, and can be reasonably considered independent and separate works in  
themselves, then this License, and its terms, do not apply to those sections when you distribute them as  
separate works. But when you distribute the same sections as part of a whole which is a work based on  
the Program, the distribution of the whole must be on the terms of this License, whose permissions for  
other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by  
you; rather, the intent is to exercise the right to control the distribution of derivative or collective works  
based on the Program.  
In addition, mere aggregation of another work not based on the Program with the Program (or with a  
work based on the Program) on a volume of a storage or distribution medium does not bring the other  
work under the scope of this License.  
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or  
executable form under the terms of Sections 1 and 2 above provided that you also do one of the  
following:  
a) Accompany it with the complete corresponding machine-readable source code, which must be  
distributed under the terms of Sections 1 and 2 above on a medium customarily used for software  
interchange; or,  
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no  
more than your cost of physically performing source distribution, a complete machine-readable copy of  
the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a  
medium customarily used for software interchange; or,  
c) Accompany it with the information you received as to the offer to distribute corresponding source  
code. (This alternative is allowed only for noncommercial distribution and only if you received the  
program in object code or executable form with such an offer, in accord with Subsection b above.)  
The source code for a work means the preferred form of the work for making modifications to it. For an  
executable work, complete source code means all the source code for all modules it contains, plus any  
214  
associated interface definition files, plus the scripts used to control compilation and installation of the  
executable. However, as a special exception, the source code distributed need not include anything that  
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and  
so on) of the operating system on which the executable runs, unless that component itself accompanies  
the executable.  
If distribution of executable or object code is made by offering access to copy from a designated place,  
then offering equivalent access to copy the source code from the same place counts as distribution of  
the source code, even though third parties are not compelled to copy the source along with the object  
code.  
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under  
this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will  
automatically terminate your rights under this License. However, parties who have received copies, or  
rights, from you under this License will not have their licenses terminated so long as such parties remain  
in full compliance.  
5. You are not required to accept this License, since you have not signed it. However, nothing else  
grants you permission to modify or distribute the Program or its derivative works. These actions are  
prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program  
(or any work based on the Program), you indicate your acceptance of this License to do so, and all its  
terms and conditions for copying, distributing or modifying the Program or works based on it.  
6. Each time you redistribute the Program (or any work based on the Program), the recipient  
automatically receives a license from the original licensor to copy, distribute or modify the Program  
subject to these terms and conditions. You may not impose any further restrictions on the recipients'  
exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to  
this License.  
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason  
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or  
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of  
this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License  
and any other pertinent obligations, then as a consequence you may not distribute the Program at all.  
For example, if a patent license would not permit royalty-free redistribution of the Program by all those  
who receive copies directly or indirectly through you, then the only way you could satisfy both it and this  
License would be to refrain entirely from distribution of the Program.  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the  
balance of the section is intended to apply and the section as a whole is intended to apply in other  
circumstances.  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or  
to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the  
free software distribution system, which is implemented by public license practices. Many people have  
215  
made generous contributions to the wide range of software distributed through that system in reliance on  
consistent application of that system; it is up to the author/donor to decide if he or she is willing to  
distribute software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this  
License.  
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by  
copyrighted interfaces, the original copyright holder who places the Program under this License may add  
an explicit geographical distribution limitation excluding those countries, so that distribution is permitted  
only in or among countries not thus excluded. In such case, this License incorporates the limitation as if  
written in the body of this License.  
9. The Free Software Foundation may publish revised and/or new versions of the General Public  
License from time to time. Such new versions will be similar in spirit to the present version, but may differ  
in detail to address new problems or concerns.  
Each version is given a distinguishing version number. If the Program specifies a version number of this  
License which applies to it and "any later version", you have the option of following the terms and  
conditions either of that version or of any later version published by the Free Software Foundation. If the  
Program does not specify a version number of this License, you may choose any version ever published  
by the Free Software Foundation.  
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions  
are different, write to the author to ask for permission. For software which is copyrighted by the Free  
Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.  
Our decision will be guided by the two goals of preserving the free status of all derivatives of our free  
software and of promoting the sharing and reuse of software generally.  
NO WARRANTY  
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR  
THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN  
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES  
PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR  
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,  
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL  
ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE  
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE  
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR  
216  
DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES  
OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH  
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your New Programs  
If you develop a new program, and you want it to be of the greatest possible use to the public, the best  
way to achieve this is to make it free software which everyone can redistribute and change under these  
terms.  
To do so, attach the following notices to the program. It is safest to attach them to the start of each  
source file to most effectively convey the exclusion of warranty; and each file should have at least the  
"copyright" line and a pointer to where the full notice is found.  
<one line to give the program's name and a brief idea of what it does.>  
Copyright (c) <year> <name of author>  
This program is free software; you can redistribute it and/or modify it under the terms of the GNU  
General Public License as published by the Free Software Foundation; either version 2 of the License, or  
(at your option) any later version.  
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without  
even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See  
the GNU General Public License for more details.  
You should have received a copy of the GNU General Public License along with this program; if not,  
write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301  
USA.  
Also add information on how to contact you by electronic and paper mail.  
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:  
Gnomovision version 69, Copyright (c) year name of author Gnomovision comes with ABSOLUTELY NO  
WARRANTY; for details type 'show w'. This is free software, and you are welcome to redistribute it under  
certain conditions; type 'show c' for details.  
The hypothetical commands 'show w' and 'show c' should show the appropriate parts of the General  
Public License. Of course, the commands you use may be called something other than 'show w' and  
'show c'; they could even be mouse-clicks or menu items--whatever suits your program.  
You should also get your employer (if you work as a programmer) or your school, if any, to sign a  
"copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the program 'Gnomovision' (which makes  
passes at compilers) written by James Hacker.  
217  
<signature of Ty Coon>, 1 April 1989  
Ty Coon, President of Vice  
This General Public License does not permit incorporating your program into proprietary programs. If  
your program is a subroutine library, you may consider it more useful to permit linking proprietary  
applications with the library. If this is what you want to do, use the GNU Lesser General Public License  
instead of this License.  
GNU LGPL  
This projector product includes the open source software programs which apply the GNU Lesser  
General Public License Version 2 or later version ("LGPL Programs").  
We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same  
model of this projector product.  
If you desire to receive the source code of the LGPL Programs, please see the "EPSON Projector  
Contact List" in the User's Guide, and contact the customer support of your region.  
These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public  
License for more details.  
The list of LGPL Programs is as follows and the names of author are described in the source code of the  
LGPL Programs.  
LGPL Programs  
glibc-2.8  
SDL-1.2.13  
SDL-Image  
The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser  
General Public License Version 2 at http://www.gnu.org/licenses/.  
GNU LESSER GENERAL PUBLIC LICENSE  
Version 2.1, February 1999  
Copyright ©) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA  
02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document,  
but changing it is not allowed.  
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library  
Public License, version 2, hence the version number 2.1.]  
Preamble  
218  
The licenses for most software are designed to take away your freedom to share and change it. By  
contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and  
change free software--to make sure the software is free for all its users.  
This license, the Lesser General Public License, applies to some specially designated software  
packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.  
You can use it too, but we suggest you first think carefully about whether this license or the ordinary  
General Public License is the better strategy to use in any particular case, based on the explanations  
below.  
When we speak of free software, we are referring to freedom of use, not price. Our General Public  
Licenses are designed to make sure that you have the freedom to distribute copies of free software (and  
charge for this service if you wish); that you receive source code or can get it if you want it; that you can  
change the software and use pieces of it in new free programs; and that you are informed that you can  
do these things.  
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to  
ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you  
distribute copies of the library or if you modify it.  
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the  
recipients all the rights that we gave you. You must make sure that they, too, receive or can get the  
source code. If you link other code with the library, you must provide complete object files to the  
recipients, so that they can relink them with the library after making changes to the library and  
recompiling it. And you must show them these terms so they know their rights.  
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this  
license, which gives you legal permission to copy, distribute and/or modify the library.  
To protect each distributor, we want to make it very clear that there is no warranty for the free library.  
Also, if the library is modified by someone else and passed on, the recipients should know that what they  
have is not the original version, so that the original author's reputation will not be affected by problems  
that might be introduced by others.  
Finally, software patents pose a constant threat to the existence of any free program. We wish to make  
sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive  
license from a patent holder. Therefore, we insist that any patent license obtained for a version of the  
library must be consistent with the full freedom of use specified in this license.  
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.  
This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite  
different from the ordinary General Public License. We use this license for certain libraries in order to  
permit linking those libraries into non-free programs.  
When a program is linked with a library, whether statically or using a shared library, the combination of  
the two is legally speaking a combined work, a derivative of the original library. The ordinary General  
219  
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The  
Lesser General Public License permits more lax criteria for linking other code with the library.  
We call this license the "Lesser" General Public License because it does Less to protect the user's  
freedom than the ordinary General Public License. It also provides other free software developers Less  
of an advantage over competing non-free programs. These disadvantages are the reason we use the  
ordinary General Public License for many libraries. However, the Lesser license provides advantages in  
certain special circumstances.  
For example, on rare occasions, there may be a special need to encourage the widest possible use of a  
certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be  
allowed to use the library. A more frequent case is that a free library does the same job as widely used  
non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we  
use the Lesser General Public License.  
In other cases, permission to use a particular library in non-free programs enables a greater number of  
people to use a large body of free software. For example, permission to use the GNU C Library in non-  
free programs enables many more people to use the whole GNU operating system, as well as its variant,  
the GNU/Linux operating system.  
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that  
the user of a program that is linked with the Library has the freedom and the wherewithal to run that  
program using a modified version of the Library.  
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to  
the difference between a "work based on the library" and a "work that uses the library". The former  
contains code derived from the library, whereas the latter must be combined with the library in order to  
run.  
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,  
DISTRIBUTION AND MODIFICATION  
0. This License Agreement applies to any software library or other program which contains a notice  
placed by the copyright holder or other authorized party saying it may be distributed under the terms of  
this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".  
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked  
with application programs (which use some of those functions and data) to form executables.  
The "Library", below, refers to any such software library or work which has been distributed under these  
terms. A "work based on the Library" means either the Library or any derivative work under copyright  
law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications  
and/or translated straightforwardly into another language. (Hereinafter, translation is included without  
limitation in the term "modification".)  
220  
"Source code" for a work means the preferred form of the work for making modifications to it. For a  
library, complete source code means all the source code for all modules it contains, plus any associated  
interface definition files, plus the scripts used to control compilation and installation of the library.  
Activities other than copying, distribution and modification are not covered by this License; they are  
outside its scope. The act of running a program using the Library is not restricted, and output from such a  
program is covered only if its contents constitute a work based on the Library (independent of the use of  
the Library in a tool for writing it). Whether that is true depends on what the Library does and what the  
program that uses the Library does.  
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it,  
in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate  
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the  
absence of any warranty; and distribute a copy of this License along with the Library.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer  
warranty protection in exchange for a fee.  
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on  
the Library, and copy and distribute such modifications or work under the terms of Section 1 above,  
provided that you also meet all of these conditions:  
a) The modified work must itself be a software library.  
b) You must cause the files modified to carry prominent notices stating that you changed the files and the  
date of any change.  
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms  
of this License.  
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application  
program that uses the facility, other than as an argument passed when the facility is invoked, then you  
must make a good faith effort to ensure that, in the event an application does not supply such function or  
table, the facility still operates, and performs whatever part of its purpose remains meaningful.  
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined  
independent of the application. Therefore, Subsection 2d requires that any application-supplied function  
or table used by this function must be optional: if the application does not supply it, the square root  
function must still compute square roots.)  
These requirements apply to the modified work as a whole. If identifiable sections of that work are not  
derived from the Library, and can be reasonably considered independent and separate works in  
themselves, then this License, and its terms, do not apply to those sections when you distribute them as  
separate works. But when you distribute the same sections as part of a whole which is a work based on  
the Library, the distribution of the whole must be on the terms of this License, whose permissions for  
other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.  
221  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by  
you; rather, the intent is to exercise the right to control the distribution of derivative or collective works  
based on the Library.  
In addition, mere aggregation of another work not based on the Library with the Library (or with a work  
based on the Library) on a volume of a storage or distribution medium does not bring the other work  
under the scope of this License.  
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to  
a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that  
they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer  
version than version 2 of the ordinary GNU General Public License has appeared, then you can specify  
that version instead if you wish.) Do not make any other change in these notices.  
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General  
Public License applies to all subsequent copies and derivative works made from that copy.  
This option is useful when you wish to copy part of the code of the Library into a program that is not a  
library.  
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code  
or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the  
complete corresponding machine-readable source code, which must be distributed under the terms of  
Sections 1 and 2 above on a medium customarily used for software interchange.  
If distribution of object code is made by offering access to copy from a designated place, then offering  
equivalent access to copy the source code from the same place satisfies the requirement to distribute  
the source code, even though third parties are not compelled to copy the source along with the object  
code.  
5. A program that contains no derivative of any portion of the Library, but is designed to work with the  
Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in  
isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.  
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative  
of the Library (because it contains portions of the Library), rather than a "work that uses the library". The  
executable is therefore covered by this License. Section 6 states terms for distribution of such  
executables.  
When a "work that uses the Library" uses material from a header file that is part of the Library, the object  
code for the work may be a derivative work of the Library even though the source code is not. Whether  
this is true is especially significant if the work can be linked without the Library, or if the work is itself a  
library. The threshold for this to be true is not precisely defined by law.  
If such an object file uses only numerical parameters, data structure layouts and accessors, and small  
macros and small inline functions (ten lines or less in length), then the use of the object file is  
222  
unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object  
code plus portions of the Library will still fall under Section 6.)  
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under  
the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not  
they are linked directly with the Library itself.  
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library"  
with the Library to produce a work containing portions of the Library, and distribute that work under terms  
of your choice, provided that the terms permit modification of the work for the customer's own use and  
reverse engineering for debugging such modifications.  
You must give prominent notice with each copy of the work that the Library is used in it and that the  
Library and its use are covered by this License. You must supply a copy of this License. If the work  
during execution displays copyright notices, you must include the copyright notice for the Library among  
them, as well as a reference directing the user to the copy of this License. Also, you must do one of  
these things:  
a) Accompany the work with the complete corresponding machine-readable source code for the Library  
including whatever changes were used in the work (which must be distributed under Sections 1 and 2  
above); and, if the work is an executable linked with the Library, with the complete machine-readable  
"work that uses the Library", as object code and/or source code, so that the user can modify the Library  
and then relink to produce a modified executable containing the modified Library. (It is understood that  
the user who changes the contents of definitions files in the Library will not necessarily be able to  
recompile the application to use the modified definitions.)  
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that  
(1) uses at run time a copy of the library already present on the user's computer system, rather than  
copying library functions into the executable, and (2) will operate properly with a modified version of the  
library, if the user installs one, as long as the modified version is interface-compatible with the version  
that the work was made with.  
c) Accompany the work with a written offer, valid for at least three years, to give the same user the  
materials specified in Subsection 6a, above, for a charge no more than the cost of performing this  
distribution.  
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent  
access to copy the above specified materials from the same place.  
e) Verify that the user has already received a copy of these materials or that you have already sent this  
user a copy.  
For an executable, the required form of the "work that uses the Library" must include any data and utility  
programs needed for reproducing the executable from it. However, as a special exception, the materials  
to be distributed need not include anything that is normally distributed (in either source or binary form)  
223  
with the major components (compiler, kernel, and so on) of the operating system on which the  
executable runs, unless that component itself accompanies the executable.  
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that  
do not normally accompany the operating system. Such a contradiction means you cannot use both  
them and the Library together in an executable that you distribute.  
7. You may place library facilities that are a work based on the Library side-by-side in a single library  
together with other library facilities not covered by this License, and distribute such a combined library,  
provided that the separate distribution of the work based on the Library and of the other library facilities is  
otherwise permitted, and provided that you do these two things:  
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with  
any other library facilities. This must be distributed under the terms of the Sections above.  
b) Give prominent notice with the combined library of the fact that part of it is a work based on the  
Library, and explaining where to find the accompanying uncombined form of the same work.  
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided  
under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library  
is void, and will automatically terminate your rights under this License. However, parties who have  
received copies, or rights, from you under this License will not have their licenses terminated so long as  
such parties remain in full compliance.  
9. You are not required to accept this License, since you have not signed it. However, nothing else  
grants you permission to modify or distribute the Library or its derivative works. These actions are  
prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or  
any work based on the Library), you indicate your acceptance of this License to do so, and all its terms  
and conditions for copying, distributing or modifying the Library or works based on it.  
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically  
receives a license from the original licensor to copy, distribute, link with or modify the Library subject to  
these terms and conditions. You may not impose any further restrictions on the recipients' exercise of  
the rights granted herein. You are not responsible for enforcing compliance by third parties with this  
License.  
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason  
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or  
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of  
this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License  
and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For  
example, if a patent license would not permit royalty-free redistribution of the Library by all those who  
receive copies directly or indirectly through you, then the only way you could satisfy both it and this  
License would be to refrain entirely from distribution of the Library.  
224  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the  
balance of the section is intended to apply, and the section as a whole is intended to apply in other  
circumstances.  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or  
to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the  
free software distribution system which is implemented by public license practices. Many people have  
made generous contributions to the wide range of software distributed through that system in reliance on  
consistent application of that system; it is up to the author/donor to decide if he or she is willing to  
distribute software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this  
License.  
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by  
copyrighted interfaces, the original copyright holder who places the Library under this License may add  
an explicit geographical distribution limitation excluding those countries, so that distribution is permitted  
only in or among countries not thus excluded. In such case, this License incorporates the limitation as if  
written in the body of this License.  
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General  
Public License from time to time. Such new versions will be similar in spirit to the present version, but  
may differ in detail to address new problems or concerns.  
Each version is given a distinguishing version number. If the Library specifies a version number of this  
License which applies to it and "any later version", you have the option of following the terms and  
conditions either of that version or of any later version published by the Free Software Foundation. If the  
Library does not specify a license version number, you may choose any version ever published by the  
Free Software Foundation.  
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions  
are incompatible with these, write to the author to ask for permission. For software which is copyrighted  
by the Free Software Foundation, write to the Free Software Foundation; we sometimes make  
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all  
derivatives of our free software and of promoting the sharing and reuse of software generally.  
NO WARRANTY  
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR  
THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE  
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE  
LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,  
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND  
225  
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,  
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL  
ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE  
THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE  
OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA  
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A  
FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH  
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your New Libraries  
If you develop a new library, and you want it to be of the greatest possible use to the public, we  
recommend making it free software that everyone can redistribute and change. You can do so by  
permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General  
Public License).  
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of  
each source file to most effectively convey the exclusion of warranty; and each file should have at least  
the "copyright" line and a pointer to where the full notice is found.  
<one line to give the library's name and a brief idea of what it does.>  
Copyright (c) <year> <name of author>  
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser  
General Public License as published by the Free Software Foundation; either version 2.1 of the License,  
or (at your option) any later version.  
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even  
the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the  
GNU Lesser General Public License for more details.  
You should have received a copy of the GNU Lesser General Public License along with this library; if  
not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301  
USA  
Also add information on how to contact you by electronic and paper mail.  
You should also get your employer (if you work as a programmer) or your school, if any, to sign a  
"copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the library 'Frob' (a library for tweaking knobs)  
written by James Random Hacker.  
226  
<signature of Ty Coon>, 1 April 1990  
Ty Coon, President of Vice  
That's all there is to it!  
BSD License (Berkeley Software Distribution License)  
This projector product includes the open source software program "University of California, Berkeley  
License (Berkeley Software Distribution License)" which applies the terms and conditions provided by  
owner of the copyright to the "BSD License".  
The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of BSD License programs  
busybox-1.13.4  
License terms of conditions of each program which are provided by owner of the copyright to the "BSD  
License" are as follows.  
Copyright (c) The Regents of the University of California. All rights reserved.  
This code is derived from software contributed to Berkeley by Kenneth Almquist.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. Neither the name of the University nor the names of its contributors may be used to endorse or  
promote products derived from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
227  
libjpeg  
This projector product includes the open source software program "libjpeg" which applies the terms and  
conditions provided by owner of the copyright to the "libjpeg".  
The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of libjpeg programs  
libjpeg-6b  
License terms of conditions of each program which are provided by owner of the copyright to the  
"libjpeg" are as follows.  
Copyright (c) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software.  
For conditions of distribution and use, see the accompanying README file.  
This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.  
You are welcome to redistribute this software and to use it for any purpose, subject to the conditions  
under LEGAL ISSUES, below.  
LEGAL ISSUES  
============  
In plain English:  
1. We don't promise that this software works. (But if you find any bugs, please let us know!)  
2. You can use this software for whatever you want. You don't have to pay us.  
3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge  
somewhere in your documentation that you've used the IJG code.  
In legalese:  
The authors make NO WARRANTY or representation, either express or implied, with respect to this  
software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is  
provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.  
This software is copyright (c) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified  
below.  
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for  
any purpose, without fee, subject to these conditions:  
(1) If any part of the source code for this software is distributed, then this README file must be included,  
with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the  
original files must be clearly indicated in accompanying documentation.  
228  
(2) If only executable code is distributed, then the accompanying documentation must state that "this  
software is based in part on the work of the Independent JPEG Group".  
(3) Permission for use of this software is granted only if the user accepts full responsibility for any  
undesirable consequences; the authors accept NO LIABILITY for damages of any kind.  
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified  
library. If you use our work, you ought to acknowledge us.  
Permission is NOT granted for the use of any IJG author's name or company name in advertising or  
publicity relating to this software or products derived from it. This software may be referred to only as  
"the Independent JPEG Group's software".  
We specifically permit and encourage the use of this software as the basis of commercial products,  
provided that all warranty or liability claims are assumed by the product vendor.  
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its  
copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered by the above  
copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation;  
principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.)  
However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does  
not limit you more than the foregoing paragraphs do.  
The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free  
Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess,  
config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely  
distributable.  
It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM,  
AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more  
licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software.  
(Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely  
that very many implementations will support it.) So far as we are aware, there are no patent restrictions  
on the remaining code.  
The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the  
Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been  
simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the  
resulting GIF files are larger than usual, but are readable by all standard GIF decoders.  
We are required to state that  
"The Graphics Interchange Format(c)) is the Copyright property of CompuServe Incorporated. GIF(sm)  
is a Service Mark property of CompuServe Incorporated."  
libpng  
229  
This projector product includes the open source software program "libpng" which applies the terms and  
conditions provided by owner of the copyright to the "libpng".  
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of libpng programs  
libpng-1.2.49  
License terms of conditions of each program which are provided by owner of the copyright to the "libpng"  
are as follows.  
This copy of the libpng notices is provided for your convenience. In case of any discrepancy between  
this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.  
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:  
If you modify libpng you may insert additional notices immediately following this sentence.  
This code is released under the libpng license.  
libpng version 1.2.6, August 15, 2004, through 1.2.49, March 29, 2012, are Copyright (c) 2004, 2006-  
2009 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as  
libpng-1.2.5 with the following individual added to the list of Contributing Authors  
Cosmin Truta  
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn  
Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with  
the following individuals added to the list of Contributing Authors  
Simon-Pierre Cadieux  
Eric S. Raymond  
Gilles Vollant  
and with the following additions to the disclaimer:  
There is no warranty against interference with your enjoyment of the library or against infringement.  
There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This  
library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and  
effort is with the user.  
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright ©) 1998, 1999 Glenn  
Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with  
the following individuals added to the list of Contributing Authors:  
Tom Lane  
230  
Glenn Randers-Pehrson  
Willem van Schaik  
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger  
Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals  
added to the list of Contributing Authors:  
John Bowler  
Kevin Bracey  
Sam Bushell  
Magnus Holmgren  
Greg Roelofs  
Tom Tanner  
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric  
Schalnat, Group 42, Inc.  
For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of  
individuals:  
Andreas Dilger  
Dave Martindale  
Guy Eric Schalnat  
Paul Schmidt  
Tim Wegner  
The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all  
warranties, expressed or implied, including, without limitation, the warranties of merchantability and of  
fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct,  
indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the  
PNG Reference Library, even if advised of the possibility of such damage.  
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for  
any purpose, without fee, subject to the following restrictions:  
1. The origin of this source code must not be misrepresented.  
2. Altered versions must be plainly marked as such and must not be misrepresented as being the  
original source.  
3. This Copyright notice may not be removed or altered from any source or altered source distribution.  
231  
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of  
this source code as a component to supporting the PNG file format in commercial products. If you use  
this source code in a product, acknowledgment is not required but would be appreciated.  
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like:  
printf("%s",png_get_copyright(NULL));  
Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg"  
(88x31) and "pngnow.png" (98x31).  
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the  
Open Source Initiative.  
Glenn Randers-Pehrson  
[email protected]  
March 29, 2012  
zlib  
This projector product includes the open source software program "zlib" which applies the terms and  
conditions provided by owner of the copyright to the "zlib".  
The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE.  
List of zlib programs  
zlib-1.1.4  
License terms of conditions of each program which are provided by owner of the copyright to the "zlib"  
are as follows.  
Copyright notice:  
(c) 1995-1998 Jean-loup Gailly and Mark Adler  
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be  
held liable for any damages arising from the use of this software.  
Permission is granted to anyone to use this software for any purpose, including commercial applications,  
and to alter it and redistribute it freely, subject to the following restrictions:  
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original  
software. If you use this software in a product, an acknowledgment in the product documentation would  
be appreciated but is not required.  
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being  
the original software.  
232  
3. This notice may not be removed or altered from any source distribution.  
Jean-loup Gailly  
[email protected] Mark Adler  
[email protected]  
If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to  
sign. The sources are provided for free but without warranty of any kind. The library has been entirely  
written by Jean-loup Gailly and Mark Adler; it does not include third-party code.  
If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history  
information documenting your changes.  
mDNSResponder  
This projector product includes the open source software program "mDNSResponder" which applies the  
following license terms "Apache License Version 2.0, January 2004".  
List of "mDNSResponder"  
mDNSResponder-107.6 (only mDNSResponderPosix is used)  
License terms "Apache License Version 2.0, January 2004" are as follows.  
Apache License  
Version 2.0, January 2004  
http://www.apache.org/licenses/  
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION  
1. Definitions.  
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by  
Sections 1 through 9 of this document.  
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the  
License.  
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled  
by, or are under common control with that entity. For the purposes of this definition, "control" means (I)  
the power, direct or indirect, to cause the direction or management of such entity, whether by contract or  
otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial  
ownership of such entity.  
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.  
"Source" form shall mean the preferred form for making modifications, including but not limited to  
software source code, documentation source, and configuration files.  
233  
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source  
form, including but not limited to compiled object code, generated documentation, and conversions to  
other media types.  
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the  
License, as indicated by a copyright notice that is included in or attached to the work (an example is  
provided in the Appendix below).  
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived  
from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications  
represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works  
shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of,  
the Work and Derivative Works thereof.  
"Contribution" shall mean any work of authorship, including the original version of the Work and any  
modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to  
Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to  
submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form  
of electronic, verbal, or written communication sent to the Licensor or its representatives, including but  
not limited to communication on electronic mailing lists, source code control systems, and issue tracking  
systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving  
the Work, but excluding communication that is conspicuously marked or otherwise designated in writing  
by the copyright owner as "Not a Contribution."  
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution  
has been received by Licensor and subsequently incorporated within the Work.  
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor  
hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable  
copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform,  
sublicense, and distribute the Work and such Derivative Works in Source or Object form.  
3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby  
grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as  
stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise  
transfer the Work, where such license applies only to those patent claims licensable by such Contributor  
that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with  
the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity  
(including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution  
incorporated within the Work constitutes direct or contributory patent infringement, then any patent  
licenses granted to You under this License for that Work shall terminate as of the date such litigation is  
filed.  
234  
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in  
any medium, with or without modifications, and in Source or Object form, provided that You meet the  
following conditions:  
(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and  
(b) You must cause any modified files to carry prominent notices stating that You changed the files; and  
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent,  
trademark, and attribution notices from the Source form of the Work, excluding those notices that do not  
pertain to any part of the Derivative Works; and  
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You  
distribute must include a readable copy of the attribution notices contained within such NOTICE file,  
excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the  
following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source  
form or documentation, if provided along with the Derivative Works; or, within a display generated by the  
Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE  
file are for informational purposes only and do not modify the License. You may add Your own attribution  
notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text  
from the Work, provided that such additional attribution notices cannot be construed as modifying the  
License.  
You may add Your own copyright statement to Your modifications and may provide additional or different  
license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such  
Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise  
complies with the conditions stated in this License.  
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally  
submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this  
License, without any additional terms or conditions.  
Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license  
agreement you may have executed with Licensor regarding such Contributions.  
6. Trademarks. This License does not grant permission to use the trade names, trademarks, service  
marks, or product names of the Licensor, except as required for reasonable and customary use in  
describing the origin of the Work and reproducing the content of the NOTICE file.  
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides  
the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT  
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation,  
any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR  
A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or  
redistributing the Work and assume any risks associated with Your exercise of permissions under this  
License.  
235  
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence),  
contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts)  
or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect,  
special, incidental, or consequential damages of any character arising as a result of this License or out of  
the use or inability to use the Work (including but not limited to damages for loss of goodwill, work  
stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if  
such Contributor has been advised of the possibility of such damages.  
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof,  
You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other  
liability obligations and/or rights consistent with this License. However, in accepting such obligations,  
You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other  
Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any  
liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such  
warranty or additional liability.  
END OF TERMS AND CONDITIONS  
APPENDIX: How to apply the Apache License to your work.  
To apply the Apache License to your work, attach the following boilerplate notice, with the fields  
enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!)  
The text should be enclosed in the appropriate comment syntax for the file format. We also recommend  
that a file or class name and description of purpose be included on the same "printed page" as the  
copyright notice for easier identification within third-party archives.  
Copyright [yyyy] [name of copyright owner]  
Licensed under the Apache License, Version 2.0 (the "License");  
you may not use this file except in compliance with the License.  
You may obtain a copy of the License at  
http://www.apache.org/licenses/LICENSE-2.0  
Unless required by applicable law or agreed to in writing, software distributed under the License is  
distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either  
express or implied.  
See the License for the specific language governing permissions and limitations under the License.  
aes-src-29-04-09  
This projector product includes the open source software program "aes-src-29-04-09" which applies the  
terms and conditions provided by owner of the copyright to the "aes-src-29-04-09".  
236  
The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of es-src-29-04-09 programs  
newlib  
This projector product includes the open source software program "newlib" which applies the terms and  
conditions provided by owner of the copyright to the "newlib".  
The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of newlib programs  
newlib 1.17.0  
License terms of conditions of each program which are provided by owner of the copyright to the "newlib"  
are as follows.  
The newlib subdirectory is a collection of software from several sources.  
Each file may have its own copyright/license that is embedded in the source file. Unless otherwise noted  
in the body of the source file(s), the following copyright notices will apply to the contents of the newlib  
subdirectory:  
(1) Red Hat Incorporated  
Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved.  
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it  
subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will  
be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available  
at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source  
code or documentation are not subject to the BSD License and may only be used or replicated with the  
express permission of Red Hat, Inc.  
(2) University of California, Berkeley  
Copyright (c) 1981-2000 The Regents of the University of California.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
* Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
237  
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
* Neither the name of the University nor the names of its contributors may be used to endorse or  
promote products derived from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"  
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE  
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL  
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR  
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF  
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(3) David M. Gay (AT&T 1991, Lucent 1998)  
The author of this software is David M. Gay.  
Copyright ©) 1991 by AT&T.  
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby  
granted, provided that this entire notice is included in all copies of any software which is or includes a  
copy or modification of this software and in all copies of the supporting documentation for such software.  
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED  
WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY  
REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF  
THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.  
-----------  
The author of this software is David M. Gay.  
Copyright (c) 1998-2001 by Lucent Technologies  
All Rights Reserved  
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and  
without fee is hereby granted, provided that the above copyright notice appear in all copies and that both  
that the copyright notice and this permission notice and warranty disclaimer appear in supporting  
documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity  
pertaining to distribution of the software without specific, written prior permission.  
LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL  
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR  
238  
ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES  
OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,  
WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,  
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.  
(4) Advanced Micro Devices  
Copyright 1989, 1990 Advanced Micro Devices, Inc.  
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user  
the right to modify, use and distribute this software provided this notice is not removed or altered. All  
other rights are reserved by AMD.  
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS  
SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL  
DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR  
USE OF THIS SOFTWARE.  
So that all may benefit from your experience, please report any problems or suggestions about this  
software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-  
89-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.  
Advanced Micro Devices, Inc.  
29K Support Products  
Mail Stop 573  
5900 E. Ben White Blvd.  
Austin, TX 78741  
800-292-9263  
(5) C.W. Sandmann  
Copyright (C) 1993 C.W. Sandmann  
This file may be freely distributed as long as the author's name remains.  
(6) Eric Backus  
(C) Copyright 1992 Eric Backus  
This software may be used freely so long as this copyright notice is left intact. There is no warrantee on  
this software.  
(7) Sun Microsystems  
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.  
239  
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and  
distribute this software is freely granted, provided that this notice is preserved.  
(8) Hewlett Packard  
(c) Copyright 1986 HEWLETT-PACKARD COMPANY  
To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty:  
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee,  
provided that the above copyright notice and this notice appears in all copies, and that the name of  
Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the  
software without specific, written prior permission. Hewlett-Packard Company makes no representations  
about the suitability of this software for any purpose.  
(9) Hans-Peter Nilsson  
Copyright (C) 2001 Hans-Peter Nilsson  
Permission to use, copy, modify, and distribute this software is freely granted, provided that the above  
copyright notice, this notice and the following disclaimer are preserved with no changes.  
THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
(11) Christopher G. Demetriou  
Copyright (c) 2001 Christopher G. Demetriou  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. The name of the author may not be used to endorse or promote products derived from this software  
without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
240  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,  
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(12) SuperH, Inc.  
Copyright 2002 SuperH, Inc. All rights reserved  
This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to  
modify, use and distribute this software provided this notice is not removed or altered. All other rights are  
reserved by SuperH.  
SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS  
SOFTWARE. IN NO EVENT SHALL SUPERH BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING,  
PERFORMANCE, OR USE OF THIS SOFTWARE.  
So that all may benefit from your experience, please report any problems or suggestions about this  
software to the SuperH Support Center via e-mail at [email protected].  
SuperH, Inc.  
405 River Oaks Parkway  
San Jose  
CA 95134  
USA  
(13) Royal Institute of Technology  
Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden).  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote  
products derived from this software without specific prior written permission.  
241  
THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS  
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(14) Alexey Zelkin  
Copyright (c) 2000, 2001 Alexey Zelkin <[email protected]>  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(15) Andrey A. Chernov  
Copyright (C) 1997 by Andrey A. Chernov, Moscow, Russia.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
242  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(16) FreeBSD  
Copyright (c) 1997-2002 FreeBSD Project.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(17) S. L. Moshier  
Author: S. L. Moshier.  
243  
Copyright (c) 1984,2000 S.L. Moshier  
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby  
granted, provided that this entire notice is included in all copies of any software which is or includes a  
copy or modification of this software and in all copies of the supporting documentation for such software.  
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED  
WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO REPRESENTATION OR WARRANTY OF  
ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR  
ANY PARTICULAR PURPOSE.  
(18) Citrus Project  
Copyright (c)1999 Citrus Project,  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(19) Todd C. Miller  
Copyright (c) 1998 Todd C. Miller <[email protected]>  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
244  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. The name of the author may not be used to endorse or promote products derived from this software  
without specific prior written permission.  
THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR  
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF  
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS  
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING  
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGE.  
(20) DJ Delorie (i386)  
Copyright (C) 1991 DJ Delorie  
All rights reserved.  
Redistribution and use in source and binary forms is permitted provided that the above copyright notice  
and following paragraph are duplicated in all such forms.  
This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  
(23) Intel (i960)  
Copyright (c) 1993 Intel Corporation  
Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.  
Intel grants this permission provided that the above copyright notice appears in all copies and that both  
the copyright notice and this permission notice appear in supporting documentation. In addition, Intel  
grants this permission provided that you prominently mark as "not part of the original" any modifications  
made to this software or documentation, and that the name of Intel Corporation not be used in  
advertising or publicity pertaining to distribution of the software or the documentation without specific,  
written prior permission.  
Intel Corporation provides this AS IS, WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED,  
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE. Intel makes no guarantee or representations regarding the use of, or the  
results of the use of, the software and documentation in terms of correctness, accuracy, reliability,  
currentness, or otherwise; and you rely on the software, documentation and results solely at your own  
risk.  
245  
IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF  
PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN  
NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE  
PRODUCT LICENSED HEREUNDER.  
(26) Mike Barcroft  
Copyright (c) 2001 Mike Barcroft <[email protected]>  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(27) Konstantin Chuguev (--enable-newlib-iconv)  
Copyright (c) 1999, 2000  
Konstantin Chuguev. All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
246  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
iconv (Charset Conversion Library) v2.0  
(28) Artem Bityuckiy (--enable-newlib-iconv)  
Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic  
Publishers.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(30) - Alex Tatmanjants (targets using libc/posix)  
Copyright (c) 1995 Alex Tatmanjants <[email protected]>  
at Electronni Visti IA, Kiev, Ukraine.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
247  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,  
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(31) - M. Warner Losh (targets using libc/posix)  
Copyright (c) 1998, M. Warner Losh <[email protected]>  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(32) - Andrey A. Chernov (targets using libc/posix)  
Copyright (C) 1996 by Andrey A. Chernov, Moscow, Russia.  
248  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(33) - Daniel Eischen (targets using libc/posix)  
Copyright (c) 2001 Daniel Eischen <[email protected]>.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
249  
(35) - ARM Ltd (arm and thumb variant targets only)  
Copyright (c) 2009 ARM Ltd  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. The name of the company may not be used to endorse or promote products derived from this software  
without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY ARM LTD "AS IS" AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,  
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(36) - CodeSourcery, Inc.  
Copyright (c) 2009 CodeSourcery, Inc.  
All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
* Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
* Neither the name of CodeSourcery nor the names of its contributors may be used to endorse or  
promote products derived from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY CODESOURCERY, INC. "AS IS" AND ANY EXPRESS OR  
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
250  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED. IN NO  
EVENT SHALL CODESOURCERY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,  
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,  
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGE.  
(37) MIPS Technologies, Inc  
/*  
* Copyright (c) 2009 MIPS Technologies, Inc.  
*
* All rights reserved.  
*
* Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
*
* * Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
* * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and  
the following disclaimer in the documentation and/or other materials provided with the distribution.  
* * Neither the name of MIPS Technologies Inc. nor the names of its contributors may be used to  
endorse or promote products derived from this software without specific prior written permission.  
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"  
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE  
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL  
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR  
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF  
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
/*  
251  
MIT License  
This projector product includes the open source software program which applies the terms and  
conditions provided by owner of the copyright to the "MIT License".  
The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  
List of MIT License programs  
jquery-1.7.2.min.js  
jquery-ui-1.8.20.custom.zip  
jquery.ui.touch-punch.js  
jquery.upload-1.0.2.min.js  
License terms of conditions of each program which are provided by owner of the copyright to the "MIT  
License" are as follows.  
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and  
associated documentation files (the "Software"), to deal in the Software without restriction, including  
without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies  
of the Software, and to permit persons to whom the Software is furnished to do so, subject to the  
following conditions:  
The above copyright notice and this permission notice shall be included in all copies or substantial  
portions of the Software.  
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR  
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS  
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS  
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,  
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN  
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.  
TOPPERS/JSP  
This projector product includes the open source software program "TOPPERS/JSP" which applies the  
terms and conditions provided by owner of the copyright to the "TOPPERS/JSP". The "TOPPERS/JSP"  
are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE.  
List of TOPPERS/JSP programs  
jsp-1.4.3  
252  
License terms of conditions of each program which are provided by owner of the copyright to the  
"TOPPERS/JSP" are as follows.  
TOPPERS/JSP Kernel  
Toyohashi Open Platform for Embedded Real-Time Systems/  
Just Standard Profile Kernel  
Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of  
Technology, JAPAN  
Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory  
Graduate School of Information Science, Nagoya Univ., JAPAN.  
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the  
conditions described in Version 2 of the GNU Public License officially announced by the Free Software  
Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization)  
of this software (this software includes alterations, likewise below) without compensation.  
(1) When this software is utilized in the form of source code, the above copyright declaration, these  
conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged  
form inside the source code.  
(2) When this software is redistributed in a form in which it can be used in the development of other  
software, library form, etc., the above copyright display, these terms of utilization, and the following  
stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's  
manual, etc.).  
(3) When this software is redistributed in a form in which it cannot be used in the development of other  
software, embedded in devices, etc., one of the following conditions shall be satisfied.  
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee  
shall be inserted in documentation accompanying redistribution (user's manual, etc.).  
(b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided  
otherwise.  
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for  
whatever damages occur either directly or indirectly through the utilization of this software.  
This software is something that is provided with no guarantee. The above copyright holder and the  
TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of  
its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear  
responsibility for whatever damages occur either directly or indirectly through the utilization of this  
software.  
253  
Note: The TOPPERS License has been revised several times; what is shown above is the latest version  
that is to be applied to software made public hereafter.  
TINET  
This projector product includes the open source software program "TINET" which applies the terms and  
conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY  
WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE.  
List of TINET programs  
tinet-1.4.4  
License terms of conditions of each program which are provided by owner of the copyright to the  
"TINET" are as follows.  
(1) FreeBSD  
Copyright (c) 1980, 1986, 1993  
The Regents of the University of California. All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided  
that the following conditions are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or other materials provided with the distribution.  
3. All advertising materials mentioning features or use of this software must display the following  
acknowledgement:  
This product includes software developed by the University of California, Berkeley and its contributors.  
4. Neither the name of the University nor the names of its contributors may be used to endorse or  
promote products derived from this software without specific prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;  
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON  
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
254  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
(6) TINET and TOPPERS  
TINET (TCP/IP Protocol Stack)  
Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of  
Technology, JAPAN  
TINET (TCP/IP Protocol Stack)  
Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of  
Technology, JAPAN  
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the  
conditions described in Version 2 of the GNU Public License officially announced by the Free Software  
Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization)  
of this software (this software includes alterations, likewise below) without compensation.  
(1) When this software is utilized in the form of source code, the above copyright declaration, these  
conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged  
form inside the source code.  
(2) When this software is redistributed in a form in which it can be used in the development of other  
software, library form, etc., the above copyright display, these terms of utilization, and the following  
stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's  
manual, etc.).  
(3) When this software is redistributed in a form in which it cannot be used in the development of other  
software, embedded in devices, etc., following conditions shall be satisfied.  
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee  
shall be inserted in documentation accompanying redistribution (user's manual, etc.).  
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for  
whatever damages occur either directly or indirectly through the utilization of this software.  
This software is something that is provided with no guarantee. The above copyright holder and the  
TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of  
its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear  
responsibility for whatever damages occur either directly or indirectly through the utilization of this  
software.  
Tomakomai National College of Technology, JAPAN  
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the  
conditions described in Version 2 of the GNU Public License officially announced by the Free Software  
255  
Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization)  
of this software (this software includes alterations, likewise below) without compensation.  
(1) When this software is utilized in the form of source code, the above copyright declaration, these  
conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged  
form inside the source code.  
(2) When this software is redistributed in a form in which it can be used in the development of other  
software, library form, etc., the above copyright display, these terms of utilization, and the following  
stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's  
manual, etc.).  
(3) When this software is redistributed in a form in which it cannot be used in the development of other  
software, embedded in devices, etc., following conditions shall be satisfied.  
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee  
shall be inserted in documentation accompanying redistribution (user's manual, etc.).  
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for  
whatever damages occur either directly or indirectly through the utilization of this software.  
This software is something that is provided with no guarantee. The above copyright holder and the  
TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of  
its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear  
responsibility for whatever damages occur either directly or indirectly through the utilization of this  
software.  
Parent topic: Notices  
Copyright Notice  
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or  
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,  
without the prior written permission of Seiko Epson Corporation. The information contained herein is  
designed only for use with this Epson product. Epson is not responsible for any use of this information as  
applied to other products.  
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third  
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of:  
accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this  
product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and  
maintenance instructions.  
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any  
options or any consumable products other than those designated as Original Epson Products or Epson  
Approved Products by Seiko Epson Corporation.  
256  
 
This information is subject to change without notice.  
A Note Concerning Responsible Use of Copyrighted Materials  
Copyright Attribution  
Parent topic: Notices  
A Note Concerning Responsible Use of Copyrighted Materials  
Epson encourages each user to be responsible and respectful of the copyright laws when using any  
Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in  
certain circumstances, those circumstances may not be as broad as some people assume. Contact your  
legal advisor for any questions regarding copyright law.  
Parent topic: Copyright Notice  
Copyright Attribution  
© 2016 Epson America, Inc.  
8/16  
CPD-41714R1  
Parent topic: Copyright Notice  
257  
   

Zebra Technologies Zebra Xi4tm User Manual
York 14 User Manual
Skil 7305 User Manual
Sears Diehard Portable Power 1150 2871988 User Manual
Sanyo Khs1852 S User Manual
Samsung Aw1201m User Manual
Panasonic Kx Tg1837al User Manual
Newair Acp 1000e User Manual
D LINK DCS 6815 User Manual
ACER D613 User Manual