ENTTEC WINGS 70033 User Manual

Quick Start Manual  
MANUAL-WING (NC)  
For latest version visit:  
Status Led indicating if the device is powered up and  
running. Blinks at 1Hz in normal mode, blinks at 5Hz  
when  
Activity Led indicates the network capacity. (ON to  
indicate 100Mb connection, and OFF to indicate  
10Mb connection)  
Link led indicating the presence of an Ethernet  
connection.  
7V DC power connector  
Box Contents  
ENTTEC Wing (70031, 70032 or 70033)  
7V Power supply (79111)  
Country specific plug for power supply  
Cat5 patch cable (79102)  
Default IP address Label  
This user manual  
Shortcut Wing Features  
Note: The user manual for all ENTTEC Wings is the same.  
Please refer to the section relating to that specific product.  
Ethernet Interface  
60 High quality Cherry MX Keys  
2 Digit 7 Segment LED display  
PAGE UP & PAGE DOWN Keys  
Upgradeable firmware (using web-interface)  
Introduction  
ENTTEC Playback Wing supports two modes, and only one  
mode can be active at a single time:  
ENTTEC Mode: Default mode, and is supported by  
software such as D-PRO and Lightfactory.  
Art-Net Mode: Each key can be mapped to an Art-  
Net channel and used as required.  
Playback Wing Features  
Ethernet Interface  
40 High quality Cherry MX Keys  
10 High Quality 60mm Faders  
2 Digit 7 Segment LED display  
PAGE UP & PAGE DOWN Keys  
Large GO & BACK Keys  
ENTTEC Shortcut and Program wings only support  
ENTTEC Mode.  
Other software programs might support ENTTEC wings,  
and their operation as it relates to those software titles will  
be explained in full by those vendors.  
After, un-packing the unit from the box, on the rear panel,  
you will find:  
Upgradeable firmware (using web-interface)  
RJ45 Ethercon connector for a 10/100Mb  
connection  
Program Wing Features  
Ethernet Interface  
1
ID: 210583  
Quick Start Manual  
MANUAL-WING (NC)  
For latest version visit:  
When the update is complete, the page will refresh and  
you will be taken to the home page where you can verify  
the firmware version.  
Since, ENTTEC Wing will reboot after a firmware update,  
please allow a few seconds for it to be refreshed in the  
browser. Please wait until the update process is complete.  
NMU  
NMU (Node Management Utility) is a free Windows and  
Mac application that is used to manage compatible  
ENTTEC nodes over Ethernet.  
1. Download NMU from: enttec.com/nmu  
To update the firmware on the Wing, please use “Update  
Firmware” page, and follow the steps given below.  
2. Ensure that your ENTTEC Wing is hooked up physically by  
Ethernet cable, to your network.  
Firmware Update  
3. Open NMU. If prompted with multiple networks, select the  
correct network. (Identified by the IP address of your com-  
puter on the network, to which the Wing is connected.)  
From this page you can update the latest firmware of the  
ENTTEC Wing (firmware  
file  
is  
available at  
enttec.com/wing). All 3 types of Wing use the same  
firmware file.  
Choose or browse the firmware file (as per your browser)  
and click on Update firmware to start the process.  
4. Press the Discovery button, and wait till NMU finds all sup-  
ported ENTTEC devices on your network. Select the Wing and  
click Configure.  
The update progress is shown in real-time, and will take a  
few seconds for the update to complete.  
3
ID: 210583  
Quick Start Manual  
MANUAL-WING (NC)  
For latest version visit:  
ENTTEC Wings are supported by various software titles. Please  
refer to the respective software user-manual or online guide  
for more details on what functions are supported, and  
how to setup the Wings:  
Art-Net Mode: Playback Wing  
D-PRO User Manual  
LightFactory User Guide  
FreeStyler  
QLC+  
Wing Specifications  
You will need to select the Subnet and Universe from the  
appropriate pulldowns in the Art-Net mode, which will tell  
the Wing which Art-Net universe of the 255 possible  
choices to use for the information it generates.  
Due to continuous improvements and innovations of all  
ENTTEC products, specifications and features are subject to  
change without notice.  
Item  
Value  
7-9V DC  
You can assign a total of 50 addresses to the 10 sliders and  
the 40 buttons. The buttons have the option to be set for  
Toggle or Flash, for each button.  
Power Requirements  
Weight  
6.6 lbs / 3.0 Kg  
13.4” / 340mm  
9.45” / 240mm  
1.26” / 32mm  
AUTOFILL: The Auto Fill button will return the assignments  
to the default configuration, shown above.  
Length  
Width  
SET CONFIG TO WING: Saves the changed configuration  
to the Wing.  
Height  
PAGE UP/DN: In addition to the 50 you have selected on  
the main screen, you have access to up to 450 other DMX  
addresses in the same Art- Net universe by pressing Page  
Up and Page Down buttons on the Wing.  
Op Environment  
Connectors  
0°-50°C  
1x RJ45 Ethercon connector  
In the example shown above, on Page 2, the sliders would  
correspond to channels 51-60.  
Ordering Information  
The ENTTEC Wings and compatible products can be ordered  
from our website or through your ENTTEC dealer.  
EXCEEDING CHANNEL 512: Starting at higher than 62,  
you may run out of room on page 10 or even before. Such  
an arrangement would simply mean that on that page the  
button or slider does nothing.  
PN  
Description  
70031  
Shortcut Wing  
70032  
70033  
Playback Wing  
Program Wing  
Supported Software  
4
ID: 210583  
Quick Start Manual  
MANUAL-WING (NC)  
For latest version visit:  
70573  
70043  
D-PRO 2U  
Wing Rackmount Kit  
5
ID: 210583  

Sanyo 36k72r User Manual
Philips Multilife Scb5360cb User Manual
HP DESIGNJET 3500 User Manual
Ge 33715 User Manual
FUJITSU FI 7030 User Manual
DELL XPS 400 User Manual
CRAFTSMAN 486.24839 User Manual
BROTHER HL 5440D 02 User Manual
BROTHER HL 4140CN User Manual
BLACK DECKER PI100BB User Manual