BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 1
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan/Light
Receiver & Reverse Module
Owner's Manual
For Use With SR600 Remote Control,
SR650 Remote Control and SW605 Wall Control
Receiver Model Numbers:
RCK55
6-Speed Receiver
RCK55 Receiver Supplied with Reverse Module for K55 Motor Fans
The RCK55 Receiver and Module for Use Only with
Emerson Ceiling Fan Models: CF4800, CF4500, CF2400,CF2000,
CF3900, CF3600, & CF1.
Part No. F40BP74160000
Form No. BP7416
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 3
General
Your Emerson Ceiling Fanl may be used
with a SR600 or SR650 Remote Control, a
SECTION ONE:
SR600 REMOTE
SW605 Wall Control, and a RCK55 6- CONTROL PROCEDURES
speed Receiver. The remote control or
wall control is designed to control your
General
ceiling fan speed, airflow direction, and
Your Emerson Ceiling Fan/Light SR600
light intensity.
Remote Control consists of hand-held
NOTE: The RCK55 Receiver and
Module for Use Only with Emerson
Ceiling Fan Models: CF4800, CF4500,
CF2400,CF2000, CF3900, CF3600, &
CF1.
transmitter and a receiver which is
mounted under the fan ceiling cover. The
remote control is designed to separately
control your ceiling fan speed and light
intensity.
The remote control transmitter is powered
by two AAA alkaline batteries (not
included). To prevent possible damage if
the batteries should leak, be sure to
remove the batteries when the control is
not to be used for an extended period of
time.
Unpackaging
The carton with the RCK55 Receiver also
contains a reversing module, seven wire
connectors, four pull chain switch plugs,
and two rectangular switch plugs.
Code switches in the transmitter and
receiver may be set in 32 different
positions. If your fan and light go on and
off without using your control, you may be
getting interference from other remote
units such as garage door openers, car
alarms or security systems. To remedy this
situations, simply change the combination
code in your transmitter and receiver.
The carton with the SR650 Remote
Control contains a storage bracket with
two mounting screws.
The carton with the SW605 Wall Control
contains three switch covers; ivory, white
and almond color.
IMPORTANT
Preset Memory Feature
This Owner’s Manual is divided into three
sections. The first section, SR600/SR650
REMOTE CONTROL PROCEDURES,
describes how to install the two AAA
alkaline batteries in the SR600 remote
control transmitter and the two CR2032
Lithium batteries in the SR650 remote
control transmitter, and how to set the
operating frequency of the transmitter
and receiver. The second section
describes how to install the SW605 Wall
Control. These instructions must be
performed prior to installation of the
ceiling fan as described in the third
section, CEILING FAN PROCEDURES.
Your Emerson receiver is equipped with a
preset memory feature. If the AC supply to
the receiver is powered through a wall
switch, when the switch is turned OFF, the
control will remember the light intensity
and fan speed. When the switch is turned
back ON the light and fan will resume
operation as they were prior to the switch
being turned OFF.
Installation of Battery
1. Remove the battery cover by pressing
firmly below the arrow and sliding the
cover off the control (Figure 1).
2. Install two AAA alkaline batteries and
reinstall the battery cover.
3
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 4
1. Slide the five switch levers in the
REMOTE CONTROL
LEVERS
remote control to your choice of ON
(up) or down positions. Use a ball-point
pen or small screwdriver and slide the
levers firmly up or down.
ON
1
2
3
4
5
I
TWO AAA
BATTERIES
2. When power is restored, push and hold
the fan OFF button ( ) for 3 to 5
seconds to set the code in the receiver.
3. If airflow is desired in the opposite
direction, press the ( ) button on the
wall control. The fan must be operating
at any speed for the reverse button to
function. The blades will turn in the
opposite direction and reverse the
airflow.
CODE
SWITCHES
BATTERY
COMPARTMENT
COVER
SR600 REMOTE
CONTROL
Figure 1
4. To set the desired fan speed, press the
Installation of Storage
Bracket for SR600
Remote Control
( ) button to decrease the speed and
the ( ) to increase the speed. The
LED display will light up to indicate the
new speed selected.
A storage bracket is provided for holding
your remote control when not in use. If you
desire to use the bracket, install it on a
wall that is away from excess heat or
humidity (Figure 2).
5. To set the light intensity, press and
release the LIGHT (
) button to
decrease the light intensity and the
LIGHT ( ) button to increase the light
intensity. The light will turn on at the
light intensity previously selected.
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW
HOLES FOR INSTALLATION
6. The sixth switch marked ON and I is for
dimming control of lights: Set switch to
ON to allow for dimming of the lights.
Set switch to I for no dimming of the
lights such as for fluorescent bulbs.
COVER
SR650 REMOTE
CONTROL PROCEDURES
WALL
BRACKET
SCREW
HOLES (2)
General
Your Emerson Ceiling Fan/Light SR650
Remote Control consists of hand-held
transmitter with wall mount and a receiver
which is mounted under the fan ceiling
cover. The remote control is designed to
separately control your ceiling fan speed
and light intensity.
Figure 2
Setting Operating
Frequency of SR600
Remote Control
The remote control transmitter is powered
by two CR2032 Lithium batteries
(included). Be sure to remove the batteries
when the control is not to be used for an
extended period of time.
Your remote control has code switches
which must be set in one of 32 possible
code combinations. The five levers
(numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
Code switches in the transmitter and
receiver may be set in 32 different
positions. If your fan and light go on and
off without using your control, you may be
4
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 5
getting interference from other remote
units such as garage door openers, car
alarms or security systems. To remedy this
situations, simply change the combination
code in your transmitter and receiver.
WALL
BRACKET
Preset Memory Feature
Your Emerson receiver is equipped with a
preset memory feature. If the AC supply to
the receiver is powered through a wall
switch, when the switch is turned OFF, the
control will remember the light intensity
and fan speed. When the switch is turned
back ON the light and fan will resume
operation as they were prior to the switch
being turned OFF.
SCREW
HOLES (2)
Figure 4
Setting Operating
Frequency of SR650
Remote Control
Your remote control has code switches
which must be set in one of 32 possible
code combinations. The five levers
(numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
Installation of Battery
1. Remove the battery cover by pressing
firmly below the arrow and sliding the
cover off the control (Figure 3).
2. Install one CR2032 Lithium battery into
the battery compartment then stack the 1. Slide the five switch levers in the
remote control to your choice of ON
(up) or down positions. Use a ball-point
pen or small screwdriver and slide the
levers firmly up or down.
other CR2032 Lithium battery on top of
the installed battery and reinstall the
battery cover.
REMOTE CONTROL
LEVERS
ON
2. When power is restored, push and hold
the fan OFF button ( ) for 3 to 5
seconds to set the code in the receiver.
1
2
3
4
5
I
CODE
SWITCHES
SR650 REMOTE
3. If airflow is desired in the opposite
direction, press the ( ) button on the
wall control. The fan must be operating
at any speed for the reverse button to
function. The blades will turn in the
opposite direction and reverse the
airflow.
CONTROL
TWO CR2032
LITHIUM
BATTERIES
(stacked)
BATTERY
4. To set the desired fan speed, press the
COMPARTMENT
COVER
( ) button to decrease the speed and
the ( ) to increase the speed. The
Figure 3
LED display will light up to indicate the
new speed selected.
5. To set the light intensity, press and
Installation of Storage
Bracket for SR650
Remote Control
release the LIGHT (
) button to
decrease the light intensity and the
LIGHT ( ) button to increase the light
intensity. The light will turn on at the
light intensity previously selected.
A storage bracket is provided for holding
your remote control when not in use. If you
desire to use the bracket, install remote
control storatge bracket using the two
screws provided. Install on a wall that is
away from excess heat or humidity
(Figure 4).
6. The sixth switch marked ON and I is for
dimming control of lights: Set switch to
ON to allow for dimming of the lights.
Set switch to I for no dimming of the
lights such as for fluorescent bulbs.
5
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 6
Installation of Wall Control
SECTION TWO:
SINGLE-POLE INSTALLATION
Setting Operating
Frequency of SW605
Wall Control
(Figure 6)
SW605 FAN/LIGHT
HOT
BLK
WALL CONTROL
Your wall control has code switches which
must be set in one of 32 possible code
combinations (Figure 5). The five levers
(numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
BLACK
NEUTRAL
GROUND
RECEIVER LOCATED
WITHIN THE CEILING
COVER
1. Slide the five switch levers in the wall
control to your choice of ON (up) or
down positions. Use a ball-point pen or
small screwdriver and slide the levers
firmly up or down.
Figure 6
!
WARNING
2. When power is restored after
installation of the wall control, push and
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
hold the fan OFF button (
) for
3 to 5 seconds to set the code in the
receiver.
3. The sixth switch marked ON and I is for
dimming control of lights: Set switch to
ON to allow for dimming of the lights.
Set switch to I for no dimming of the
lights such as for fluorescent bulbs.
CAUTION: To reduce the risk of
electrical shock, disconnect the
electrical supply circuit before
installing the fan, light kit or receiver.
WALL CONTROL
CODE SWITCHES
ON
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
1
2
3
4
5
I
1. Disconnect electrical power to the
branch circuit at the circuit breaker or
fuse box before attempting to install the
ceiling fan wall control into the outlet box.
WALL
CONTROL
CODE
SWITCHES
2. Remove faceplate and screws from
existing wall control. Pull control out
from the wall box. Determine the “hot”
wire and the “load” wire and disconnect
these wires from control. Do not
attempt to disconnect any wires not
already connected to existing control.
Figure 5
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
6
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 7
3-WAY INSTALLATION
(On fan controlled by two different wall
controls) (See Figures 8 and 9.)
!
WARNING
Do not connect any neutral (white) wire to
this control. Incorrect wiring will damage
this control.
!
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
4. Connect one black wire of wall control
to the “hot” wire. Securely connect
wires with wire connectors supplied
(Figure 7).
5. Connect one black wire of wall switch
to the “load” (black) wire in wall box.
Securely connect wires with wire
connector supplied.
6. Screw wall control into wall box using
1. Disconnect electrical power to the
branch circuit at the circuit breaker or
fuse box before attempting to install the
ceiling fan wall control into the outlet box.
the supplied screws.
Leave wall
control in “OFF” mode until fan
installation is completed.
!
WARNING
!
WARNING
Check to see that all connections are tight
and that no bare wires are visible at the
wire connectors.
Do not connect any neutral (white) wire to
this control. Incorrect wiring will damage
this control.
7. The wall control is supplied with a
white, ivory, and almond color switch
covers. Choose the finish that best
suits your needs and snap the cover
onto the wall control (Figure 7).
2. At all wall box locations remove
faceplates and screws from existing
controls. Pull controls out from wall
boxes and determine which wall box
contains the “hot” lead and which wall
box contains the “load” wire. Also,
identify traveler wires which are
common to both wall boxes.
Disconnect wires from existing controls
only. Do not attempt to disconnect any
wires not already connected to existing
controls.
8. Install decorator wall plate (purchased
separately) using the two screws
provided with wall plate. Leave wall
control in “OFF” mode until fan
installation is completed (Figure 7).
SCREWS (2)
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
K
L
B
HOT
T
O
E
C
1
2
0
R
U
A
C
SO
T
O
L
D
OA
4. Install a wall control in the wall box
containing the “hot” wire first. Connect
the black wire of the wall control to the
“hot” wire. Securely connect wires with
wire connectors supplied.
K
D
C
N
U
LA
B
O
R
G
WALL
BOX
SWITCH
COVER
DECORATIVE
WALL PLATE
FAN/LIGHT
WALL CONTROL
5. Connect one black wire of the wall
control to both remaining traveler wires
in the wall box and secure with wire
connector supplied.
Figure 7
NOTE: Retrofit 3-way installations are
likely to include two traveler wires
between the two wall boxes. In new
construction, only one traveler wire Is
required (See Figure 9).
7
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 8
3-WAY WIRlNG DIAGRAM:
NEW CONSTRUCTION
STANDARD WIRING FOR EXISTING
3-WAY CONTROLS
!
WARNING
EXISTING
WALL CONTROL
HOT
BLK
Check to see that all connections are tight
and that no bare wires are visible at the
wire connectors.
TRAVELER WIRES
SW605
LOAD
HOT
FAN/LIGHT
3-WAY WIRING DIAGRAM: RETROFIT
BLK
WALL
CONTROL
N
BLK
BLACK
BLK
HOT BLK
LOAD
BLACK
TRAVELER
WIRE
FF
GROUND
NEUTRAL
RECEIVER LOCATED
WITHIN THE CEILING
COVER
FAN/LIGHT
WALL CONTROL
TRAVELER WIRES
LOAD
Figure 9
Figure 8
6. Screw wall control into wall box using
the supplied screws. Leave wall
Operation of Your Wall
Control (Figure 10)
control in “OFF” mode until fan
installation is completed.
7. The wall control is supplied with a
white, ivory, and almond color switch
covers. Choose the finish that best
suits your needs and snap the cover
onto the wall control (Figure 7).
IMPORTANT
Fan installation must be completed,
including the installation of the fan
blades, before testing the remote control.
8. Next, install the other wall control into
the wall box containing the load wire.
Connect the black wire of the wall
control to the traveler wire(s) already
connected to the black wire (in the
other wall box). Secure with wire
connectors supplied.
Your wall control has full control of your
fan and light.
NOTE: Prior to operation of the fan and
light from the wall control, set the fan
....
speed to HIGH ( ) and turn the light
ON (
1. To set the desired fan speed, press the
) button to decrease the speed and
).
9. Connect one black wire of the wall
control to the “load” (black) wire and
secure with wire connector supplied.
(
the ( ) to increase the speed. The LED
display will light up to indicate the new
speed selected.
2. To turn the light on and off, press and
release the LIGHT (
) button. To set
the light intensity, press and hold the
LIGHT ( ) button. The light will turn on
at the light intensity previously selected.
3. Your wall control comes complete with
your choice of three wall cover plates;
ivory, white and light almond.
8
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 9
4. If airflow is desired in the opposite
direction, press the ( ) button on the
wall control. The fan must be operating
at any speed for the reverse button to
function. The blades will turn in the
opposite direction and reverse the
airflow.
HOUSING COVER
(TYPICAL)
SCREW (TYPICAL)
CAPACITOR
SCREW (2)
SPEED
CONTROL
SWITCH
MOTOR
CONNECTOR
POWER
INDICATOR
LIGHT
KNURLED
NUT
LIGHT
BUTTON
FAN
DIRECTION
WIRING
HARNESS
CONNECTOR
PULL
HIGH TO LOW
SPEED BUTTONS
CHAIN PLUG
FAN
BUTTON
REVERSING SWITCH
SWITCH HOUSING
Figure 11
ON/OFF SWITCH
O = OFF / — = ON
3. For Ceiling Fan Models CF2400,
CF4500 and CF4800 Only. Remove
the wire connector joining the three
blue wires. (Figure 12). Separate the
blue wire coming from the ceiling fan
Figure 10
and cap this wire using
a
wire
connector (supplied). On Models
CF4500 and CF4800 only, cut the
yellow wire coming from the uplight
switch; cap the end of this wire coming
from the center of the motor using a
wire connector. On Model CF2400 only,
remove the wire connector joining the
two yellow wires; cap the yellow wire
coming from the motor using a wire
connector (orange wire on older
models). Remove the knurled nut
securing the uplight switch to the switch
housing and remove the uplight switch.
SECTION THREE:
CEILING FAN
PROCEDURES
Installation to Operate the
Ceiling Fan, Downlight
and Uplight
IMPORTANT
It is important that you also follow the
installation instructions contained in
the Owner’s Manual supplied with your
Ceiling Fan. Pay particular attention to
the Safety Instructions and WARNING
notes.
NOTE: Keep the uplight switch if you
think you may like to return to manual
control in the future.
1. Remove and retain the screws
securing the housing cover to the
switch housing (Figure 11).
2. All Ceiling Fan Models. Disconnect
the motor connector from the wiring
harness connector (Figure 11).
Remove the knurled nut securing the
speed control switch to the switch
housing.
9
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 10
SEPARATE BLUE WIRE COMING FROM CEILING
CF1 & CF2800 - INSTALL
WIRE CONNECTOR ON
YELLOW WIRE
(CF2400 - INSTALL
WIRE CONNECTOR ON
GRAY WIRE)
2
FAN AND CAP USING WIRE CONNECTOR
CF1 & CF2800
YELLOW WIRE (GRAY
ON OLDER MODELS
AND ON CF2400)
REMOVE WIRE
1
CONNECTOR SECURING
THREE BLUE WIRES
GRAY
CAPACITOR
WIRE
CUT THE
YELLOW WIRE
AND CAP USING
WIRE
CONNECTOR
3
CAPACITOR
KNURLED NUT
PULL CHAIN
PLUG
Figure 14
UPLIGHT SWITCH
Figure 12
6. For Ceiling Fan Model CF2400 Only.
Locate the gray capacitor wire which is
connected to the gray wire coming from
the center of the motor (yellow wire on
older models). Remove the wire
connector and separate these wires.
Cap the gray wire coming from the
motor using a wire connector (supplied)
(Figure 15).
4. For Ceiling Fan Models CF3900,
CF4500 and CF4800 Only.
Remove two screws securing the
reversing switch to the switch housing
(Figure 13).
7. All Ceiling Fan Models. Separate the
capacitor (held in place with two-sided
tape) from the switch housing (Figure
11) and remove the wiring harness and
switch(es) from the switch housing.
KNURLED
NUT
PULL
CHAIN
PLUG
NOTE: Keep the wiring harness if you
think you may like to return to manual
control in the future.
REVERSING SWITCH
Figure 13
5. For Ceiling Fan Models CF1, CF2000 8. All Ceiling Fan Models. Close the
and CF2800 Only. Locate the gray
capacitor wire which is connected to
the yellow wire (gray wire on older
models) coming from the center of the
motor. Remove the wire connector and
separate the gray and yellow wires.
Cap the yellow wire using a wire
connector (supplied) (Figure 14).
hole(s) for the speed control switch, the
uplight switch, and the reversing switch
by installing pull chain plug(s)
(supplied)
or
rectangular
plug
(supplied) in the hole(s). (See Figures
11, 12, and 13). Choose the color that
best matches your ceiling fan.
10
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 11
9. Position
the
reversing
module 13. For Ceiling Fan Models CF4500
(supplied) in the switch cup; connect
the reversing module connector to the
motor connector (Figure 15). The
connectors are color-coded and keyed
and can be connected in only one
manner.
and CF4800 (Newer Models) Only.
Locate the two yellow wires
terminated by a wire connector.
Remove the wire connector and
separate the wires (Figure 16). One
yellow wire comes from the motor
coupling; cap the end of this wire
using a wire connector (supplied)
(Figure 16). Separate, untwist and
unkink the 80” yellow wire lead
(supplied with the fan) and cut off the
connector from the end of the wire.
Strip 1/2-inch of insulation from the
end of this wire. Then join the 80”
yellow wire to the yellow wire from the
BLUE MOTOR & REVERSING
MODULE WIRES
WIRE
WHITE MOTOR
CONNECTOR
WIRE
REVERSING
MODULE
uplight using
a
(supplied). (Figure 17).
wire connector
NOTE: The red and brown wires
coming from the top of the motor are
capped with wire connectors. DO NOT
remove these connectors.
WHITE
REVERSING
MODULE WIRE
COLOR-CODED
REVERSING MODULE
CONNECTOR
COLOR-CODED
MOTOR CONNECTOR
DO NOT REMOVE THESE
WIRE CONNECTORS
MOTOR COUPLING
Figure 15
1
REMOVE WIRE
CONNECTOR
BROWN
WIRE
2
10. Using a wire connector (supplied),
connect the white wire from the motor
to the reversing module white wire
(Figure 15).
NOTE: If you are planning to install an
optional Emerson Light Fixture on your
ceiling fan, do not install the housing
cover (Step 10) at this time.
RED WIRE
YELLOW WIRE
FROM UPLIGHT
YELLOW WIRE FROM
MOTOR COUPLING
11. Position the housing cover (Figure
10) on the switch housing and secure
using the screws removed in Step 1.
Figure 16
DO NOT REMOVE THESE
WIRE CONNECTORS
MOTOR
COUPLING
12. Place the fan housing (top of motor
facing upward) in the lower styrofoam
pad. The lower pad serves as a
holder for the fan during the following
procedures.
RED WIRE
4
INSTALL WIRE
CONNECTOR
2
BROWN
WIRE
INSTALL
WIRE
CONNECTOR
YELLOW WIRE
FROM MOTOR COUPLING
YELLOW WIRE
FROM UPLIGHT
3
INSTALL 80" YELLOW WIRE
Figure 17
11
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 12
14. For Ceiling Fan Model CF2400 16. Assemble your ceiling fan (including
the fan blades), install the hanger
bracket, and then hang the fan in
accordance with the instructions in
the Ceiling Fan Owner’s Manual. Wire
the ceiling fan and receiver and
complete the installation in accord-
ance with the following Steps 17
through 23.
(Older Models) Only. Cut the orange
wire midway between the motor
coupling and the grommet in the
inside of the housing. Cap the orange
wire coming from the motor coupling
using a wire connector (supplied).
Separate, untwist and unkink the 80”
yellow wire lead (supplied with the
fan) and cut off the connector from the
wire. Strip 1/2-inch of insulation from
the end of this wire. Then join the 80”
yellow wire to the orange wire coming
from the inside of the housing using a
wire connector.
17. Pull the wire leads, coming from the
end of the downrod, and the supply
wires through the open side of the
hanger bracket. (Figure 18).
18. Position the RC188/RC212 Receiver
in the ceiling cover so that the flat side
of the receiver faces up and the open
portion of the receiver is to the right,
as shown in Figure 18.
15. For Ceiling Fan Models CF1 and
CF3900 Only. No wiring changes are
required on top of the motor; proceed
to Step 16.
OUTLET BOX
BLACK SUPPLY WIRE
BLACK FAN WIRE
HANGER BRACKET
HANGER BRACKET
GROUND WIRE
(GREEN)
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
BLUE RECEIVER
WIRE
OPEN
PORTION OF
RECEIVER
HERE
SUPPLY GROUND
WIRE (GREEN OR
BARE)
YELLOW FAN WIRE
YELLOW RECEIVER WIRE
RECEIVER
BLACK RECEIVER WIRE
WHITE SUPPLY
WIRE
WHITE RECEIVER WIRE
CEILING COVER
WHITE FAN WIRE
WIRE CONNECTOR
Figure 18
12
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 13
e. Cut off the end of the blue and
19. Using wire connectors (supplied),
make wiring connections as follows
(Figure 18 and 19):
yellow receiver wires and strip
back insulation 1/2” from the end
of the wires.
a. Connect the green ground wires
from the hanger bracket and the
hanger ball to the supply ground
wire (bare or green).
f. Connect the blue fan wire to the
blue receiver wire (BOTTOM
LIGHT).
g. Connect the yellow fan wire to the
yellow receiver wire (UPPER
LIGHT).
b. Connect the white fan wire and the
white supply wire to the white
receiver wire (AC IN/MOTOR N).
CAUTION: If your ceiling fan does NOT
have an uplight, there will be NO yellow
fan wire. In this case, cap the yellow
receiver wire using a wire connector
(supplied). If your ceiling fan does NOT
have a downlight, cap the blue receiver
wire using a wire connector (supplied).
c. Connect the black fan wire to the
black receiver wire (TO MOTOR
L).
d. Connect the black supply wire to
the black/white receiver wire (AC
IN L).
TO
RECEIVER
LISTED GENERAL
110V SUPPLY
USE ON/OFF WALL
BLACK
SUPPLY
WIRE
SWITCH OR
OPTIONAL
EMERSON SW605
WALL CONTROL
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
WHITE SUPPLY WIRE
BLUE RECEIVER WIRE*
YELLOW RECEIVER WIRE**
BLACK/WHITE RECEIVER WIRE
WHITE FAN WIRE
BLUE FAN WIRE
BLACK FAN WIRE
YELLOW FAN WIRE
(FROM UPLIGHT)
DOWNROD
YELLOW UPLIGHT WIRES
(NOT PRESENT ON ALL FANS)
RED AND BROWN
WIRES - CAPPED.
DO NOT REMOVE
WIRE CONNECTORS
MOTOR COUPLING
FAN HOUSING
OPTIONAL
LIGHT FIXTURE
* IF YOUR CEILING FAN DOES NOT
** IF YOUR CEILING FAN DOES NOT
HAVE AN UPLIGHT, THERE WILL BE
NO YELLOW FAN WIRE.
IN THIS CASE, CAP THE YELLOW
RECEIVER WIRE USING A WIRE
CONNECTOR.
HAVE A DOWNLIGHT, CAP THE BLUE
RECEIVER WIRE USING A WIRE
CONNECTOR.
Figure 19
13
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 14
20. Insert the connected ends of the wires
up through the open side of the
hanger bracket and into the outlet box
as shown in Figure 20.
Trouble Shooting
Fan/Light Fails to Operate
•
Check that the speed switch on the
....
fan is set to HIGH ( ) speed.
•
•
Check that the light switch is on.
OUTLET BOX
Check that the battery is good
(red indicator light should light when
any button is pressed).
HANGER
BRACKET
RECEIVER
1-1/4"
THREADED
STUDS (2)
•
•
Check that the receiver is wired
properly.
Check that code switches in the
remote control and receiver are set in
the same position.
CEILING
COVER
Short Range
Figure 20
•
If the remote control operates the fan
when close to it, but does not operate
it at a distance of 40 feet, try placing
the antenna wire outside of the ceiling
cover.
21. Screw two 1-1/4” threaded studs
(supplied with the ceiling fan) into the
tapped holes in the hanger bracket
(Figure 20).
22. Slide the receiver up and over the
hanger bracket. Press the receiver
against the ceiling, holding it in place
while installing the ceiling cover in
accordance with the instructions in
the Ceiling Fan Owner’s Manual.
23. Install the optional Emerson Light
Fixture in accordance with the
instructions in the Light Fixture
Owner’s Manual. Use the screws
removed in Step 1.
NOTE: To prevent damage to the
receiver, turn “off” the electricity at the
wall switch before installing or
removing light bulbs on the ceiling fan
or light fixture.
14
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 15
LIMITED WARRANTY
What The Warranty Covers:
All products covered by this Owner’s Manual are warranted against all defects in workmanship and
materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
All components are covered by this warranty for one year from the date you purchased your
Receiver ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO
ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson will replace a defective Emerson Receiver at no charge to you. We will ship the repaired
product or replacement to you at no charge, but you are responsible for all costs or removal,
reinstallation and shipping of the product to Emerson.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE RECEIVER TO OBTAIN LIMITED
WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the
product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag
by writing to Air Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave.,
St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the
nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or
authorized service center. Your Receiver should be properly packed to avoid damage in transit since
we will not be responsible for any such damage.
What Is Not Covered:
This warranty also does not cover any defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your receiver while in your
possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary
maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular
purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The ceiling fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia.
No other written or oral warranties apply, and no employee, agent, dealer or other person is
authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS
WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING
INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to
such damages as loss of time and loss of use. Consequential damages include but are not limited
to the cost of repairing or replacing other property which was damaged if this product does not
work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the
above exclusion or limitation may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
15
BP7416 RCK55 Receiver 10/30/09 11:20 AM Page 16
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74160000
Printed in China 10/09
Form No. BP7416
|