EMERSON QUIET KOOL EARC18RE2 User Manual

MODEL:  
EARC15RE1  
EARC18RE2  
EARC22RE2  
EARC24RE2  
INTRODUCTION  
IMPORTANT SAFETY INSTRUCTION ...........................................................................1  
ELECTRICAL REQUIREMENTS ...................................................................................2  
PACKING LIST ............................................................................................................3  
INSTALLATION & ASSEMBLY INSTRUCTIONS ............................................................. 4  
USING YOUR AIR CONDITIONER ................................................................................13  
OPERATING YOUR AIR CONDITIONER ........................................................................15  
CARE AND CLEANING ................................................................................................ 16  
TROUBLESHOOTING .................................................................................................17  
below:  
1
15K  
18K/22K/24K  
2
5/16" Long Hex-head Screw  
5/8" Long Hex-head Screw  
1/2" Long Hex-head Screw  
5/8" Long Flat Head Bolt and  
Locknut  
Sill Angle Bracket  
1/2" Long Flat Head Bolt and  
Locknut  
Gasket  
Support Bracket (with R and L )  
3
15K/18K  
17.91  
22K/24K  
18.625  
23.625  
26.50  
19.00  
19.50  
28.00  
41.00  
30.00  
41.00  
4
(15K/18K See FIG.1/FIG.2 ; 22K/24K See FIG.3/FIG.4).  
FIG.1  
FIG.2  
SASH  
SASH  
19 MIN  
1/2 MIN  
1/2 MIN  
19 MIN  
1/2 MIN  
Storm WindowFrame  
or Obstruction  
Storm WindowFrame or Obstruction  
FIG.3  
FIG.4  
SASH  
SASH  
19 1/2 MIN  
1/2 MIN  
1/2 MIN  
19 1/2 MIN  
1/2 MIN  
Storm WindowFrame  
or Obstruction  
Storm WindowFrame or Obstruction  
5
FIG.5  
FIG.6  
FIG.5  
FIG.6  
FIG.7 & 8  
FIG.9  
FIG.9  
FIG.7  
FIG.8  
6
6. Remove the six screws from the cabinet. (Top, left, and right has two screws.) (FIG.10)  
FIG.10  
FIG.11  
FIG.11  
8.Take the pearl cotton for 24K. (FIG.12)  
FIG.12  
7
FIG.13a  
FIG.13a  
Head  
5/16  
Long  
Hex-head  
Screw  
FIG.13b-14.  
FIG.13b  
5/16" Long  
Hex-head Screw  
FIG.14  
(Suggest to keep a downward angle, to let  
accumulated rain water to drain out, from back side  
of the unit bottom.)  
8
Long Flat head  
Bolt and Locknut  
5/8" Long Flat Head Bolt  
5
(It should set on the gasket for 22K/24K)  
Long  
Flat head Bolt  
and Locknut  
5/8" Long  
Hex-head Screw  
Gasket  
5/8" Long  
Hex-head Screw  
1/2" Long  
Hex-head Screw  
9
FIG.15  
10  
15K/18K  
22K/24K  
18 1/4 (46.4 cm) 19 1/2 (49.5 cm)  
23 7/8 (60.6 cm) 26 9/10 (68.3 cm)  
FIG.16  
Y
(Page 6 and 7)  
FIG.17  
FIG.18  
11  
FIG.19  
FIG.20  
12  
Cool Mode: The cooling function allows the air  
conditioner to cool the room and at the same time  
reduces humidity. Press the MODE button to  
activate the cooling function. To optimize this  
function adjust the temperature by pressing the up  
and down arrows and the speed by pressing the  
Fan Speed button.  
Dry Mode: This function reduces the humidity of  
the air to make the room more comfortable. Press  
MODE button to set the DRY mode. An automatic  
function of alternating cooling cycles and air fan  
is activated.  
AUTO  
SPEED  
AUTO  
MODE  
Fan Mode: This mode will only circulate the air.  
Press MODE button to select FAN MODE.  
Pressing the FAN SPEED button allows you to  
change the fan speed setting from HI, MED, and  
LO. If using the remote control, it will store the fan  
speed setting of the previous use.  
Auto Mode: In AUTO mode the unit automatically  
chooses the fan speed and the mode of operation  
(COOL, DRY, or FAN). In this mode the fan speed  
and the temperature are set automatically  
according to the room temperature (Room  
temperature is determined by the temperature  
sensor located in the indoor unit.).  
5. Timer Button:Use buttons on the control panel  
and remote to set the TIMER.  
Timer Off: The timed stop is programmed by  
pressing the TIMER button. Set the stop time by  
pressing the button  
or  
until your  
desired stop time is displayed, then press TIMER  
button again.  
1. Digital Display: Shows the set temperature.  
Operation modes are: Cool, Dry, Fan, and Auto.  
Time is displayed using the timer setting.  
Timer On: When the unit is off, press TIMER  
button first, set the temperature with pressing  
the button  
a second time, set the stop time with pressing the  
button or . Press TIMER button a  
or  
. Press TIMER button  
third time, confirm your settings and stop time.  
The display will show the time your machine will  
automatically turn on.  
2.  
and  
Button: Use these buttons on the  
control panel and remote to increase or decrease  
the Set Temperature or Timer.  
Note: It can be set to automatically turn off or on in  
0.5-24 hours. Each press of the  
Temperature range: 61 ~88 or 16 ~31 .  
buttons will increase or decrease the timer. The  
Timer can be set in 0.5 hours increment below 10  
hours and 1 hour increment for 10 hours or above.  
The SET light will turn on while setting.  
To cancel the set function, press the TIMER button  
again.  
3. Power Button: Turn the air conditioner on and  
off.  
4. Mode Button: Press the mode button to cycle  
through the various modes: Cool, Dry, Fan and  
Auto.  
13  
6. Eco Button: When the unit is in ECO mode, the  
light will turn on. In ECO mode, the unit will  
turn-off once the room is cooled to the user set  
temperature. The fan will also be off at this point.  
The unit will turn back on when the room  
10.Directional Louvers: Use the horizontal wheels  
to control horizontal airflow and the air deflectors  
to control vertical airflow.  
temperature rises above the user set temperature.  
Before the compressor stars, the fan motor will  
run for a while, then it will stop for a while-and will  
repeat to provide a much more comfortable-feeling  
and save energy.  
air deflector  
horizontal wheel  
air deflector  
7. Sleep Button: Press the SLEEP button, the Sleep  
Light will be on after 10s. and the remaining lights  
on the display will be off. In SLEEP mode, the air-  
conditioner will automatically adjust the  
temperature and fan speed to make the room more  
comfortable during the night. The set temperature  
will automatically raise by 1  
minutes and at most change six times until the set  
temperature is 28  
every 30-60  
.
Run time will depend on set temperature.  
8. Fan Speed Button: Press the FAN SPEED button  
to select the fan speed. In COOL MODE you can  
choose the following settings: HI, MED, LO, or  
AUTO. In FAN MODE you can choose from HI,  
MED, and LO.  
9. Fiter Button: The Filter Check light will only turn  
on as a reminder to clean the filter after the fan  
motor has been in operation for a total of 500  
hours. To turn the light off, press the Filter Check  
button.  
14  
5. Timer: Use buttons on the control panel  
and remote to set the TIMER.  
Timer Off: The timed stop is programmed by  
pressing TIMER button. Set the stop time by  
pressing the button  
or  
until your  
desired stop time is displayed, then press TIMER  
button again.  
1
2
7
Timer On: When the unit is off, press TIMER  
button first, set the temperature with pressing  
the button  
a second time, set the stop time with pressing the  
button or . Press TIMER button a  
or  
. Press TIMER button  
3
4
third time, confirm your settings and stop time.  
The display will show the time your machine will  
automatically turn on.  
Note: It can be set to automatically turn off or on in  
0.5-24 hours. Each press of the  
buttons will increase or decrease the timer. The  
Timer can be set in 0.5 hours increment below 10  
hours and 1 hour increment for 10 hours or above.  
The SET light will turn on while setting.  
To cancel the set function, press the TIMER button  
again.  
8
9
5
6
10  
3
6. Auto Mode: In AUTO mode the unit automatically  
chooses the fan speed and the mode of operation  
(COOL, DRY, or FAN). In this mode the fan speed  
and the temperature are set automatically  
according to the room temperature (Room  
temperature is determined by the temperature  
sensor located in the indoor unit.).  
1. Power: Turn the air conditioner on and off.  
7. Fan Speed: Press the FAN SPEED button  
to select the fan speed. In COOL MODE you can  
choose the following settings: HI, MED, LO, or  
AUTO. In FAN MODE you can choose from HI,  
MED, and LO.  
2. Cool: Press the COOL button to COOL mode.  
3.  
and  
: Use these buttons on the control  
panel and remote to increase or decrease the  
Set Temperature or Timer. Temperature range:  
61 ~88 or 16 ~31 .  
8. Display: To press the DISPLAY button, it can  
switch off/on all lights or LED display.  
9. Eco: When the unit is in ECO mode, the  
light will turn on. In ECO mode, the unit will  
turn-off once the room is cooled to the user set  
temperature. The fan will also be off at this point.  
The unit will turn back on when the room  
temperature rises above the user set temperature.  
Before the compressor stars, the fan motor will  
run for a while, then it will stop for a while-and will  
repeat to provide a much more comfortable-feeling  
and save energy.  
4. Sleep: Press the SLEEP button, the Sleep  
Light will be on after 10s. and the remaining  
lights on the display will be off. In SLEEP mode,  
the air-conditioner will automatically adjust the  
temperature and fan speed to make the room  
more comfortable during the night. The set  
temperature will automatically raise by 1  
every 30-60minutes and at most change six  
times until the set temperature is 28  
And every Run time will depend on set  
temperature.  
.
10. Fan Only: Press the Fan Only button to FAN  
ONLY mode.  
15  
FIG.21  
FIG.21  
16  
17  
For any questions or Technical Support,  
Please Call Customer Service: 1-844-801-8880  
18  

Weil Mclain Seer 14 User Manual
Tripp Lite Air Conditioner Srcool12k User Manual
Sony Air Conditioner Su Pw2 User Manual
Schumacher Sf 6275a Pe User Manual
Panasonic Rod End Bearing Rbt User Manual
Panasonic Kx Fg2451 User Manual
HITACHI 51F710G User Manual
EMERSON NR305TT User Manual
CANON POWERSHOT SD1200 IS User Manual
ATLAS METAL WCM BT 6 User Manual