EMERSON LC190EM2 User Manual

Español  
Français  
English  
EMERSON ANDTHE G-CLEF LOGO ARE REGISTEREDTRADEMARKS  
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.  
32” LCD TV  
LC320EM2  
22” LCD TV  
LC220EM2  
19” LCD TV  
LC190EM2  
EN Owner's Manual  
Need help?  
Please call toll free or visit our web site below  
Appelez notre numéro gratuit ou visitez notre site web à l’adresse  
FR Manuel du Propriétaire Besoin d’aide?  
ES Manual del Propietario ¿Necesita ayuda? Llame por favor sin costo ó visite nuestro sitio web en  
1-866-309-8819  
MODEL NUMBER  
SERIAL NUMBER  
© 2011 Funai Electric Co., Ltd.  
3
English  
FCC WARNING  
This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference  
unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an  
unauthorized change or modification is made.  
RADIO-TV INTERFERENCE  
This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  
If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the apparatus and receiver.  
3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.  
4) Consult the dealer or an experienced radio/TV technician for help.  
DECLARATION OF CONFORMITY  
Trade Name: Emerson  
Responsible Party: FUNAI CORPORATION, Inc.  
Address: 19900 Van Ness Avenue, Torrance, CA 90501 U.S.A.  
Telephone Number: 1-866-309-8819  
Model: LC320EM2  
LC220EM2/LC190EM2  
This Class B digital apparatus complies with Canadian ICES-003. StandardTelevision ReceivingApparatus, Canada BETS-7/NTMR-7  
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.  
Disconnect the mains plug to shut off when find trouble or not in use.The mains plug shall remain readily operable.  
This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.  
Make sure to leave a space of 4 inches (10cm) or more around this apparatus.  
WARNING: To prevent injury, this apparatus must be securely attached to the wall in accordance with the instructions.  
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or  
climbing on it. A falling unit can cause serious injury or even death.  
LAMP IN LCD CONTAINS MERCURY,DISPOSEACCORDINGTO LOCAL,STATE OR FEDERAL LAW.  
The American Academy of Pediatrics discourages television  
Trademark Information  
viewing for children younger than two years of age.  
NOTE ABOUT RECYCLING  
• This unit’s packaging materials are recyclable and  
can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are  
• Batteries should never be thrown away or incinerated  
trademarks or registered trademarks of HDMI Licensing LLC in the  
but disposed of in accordance with your local  
United States and other countries.  
regulations concerning chemical wastes.  
• For product recycling information, please visit -  
WHEN CARRYINGTHIS UNIT  
• At least 2 people are required when  
carrying this unit.  
Manufactured under license from Dolby Laboratories. Dolby and the  
• Make sure to hold the upper and bottom  
double-D symbol are trademarks of Dolby Laboratories.  
frames of the unit rmly as illustrated.  
TO AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
• Do not handle the AC power cord with wet hands.  
• Do not pull on the AC power cord when disconnecting it from an  
AC outlet. Grasp it by the plug.  
• Do not put your ngers or objects into the unit.  
LOCATION AND HANDLING  
• Do not install the unit in direct sunlight or in a place subject to dust  
or strong vibration.  
• Avoid a place with drastic temperature changes.  
• Install the unit in a horizontal and stable position. Do not place anything  
directly on top or bottom of the unit. Depending on your external  
devices, noise or disturbance of the picture and/or sound may be  
generated if the unit is placed too close to them. In this case, please  
ensure enough space between the external devices and the unit.  
• Depending on the environment, the temperature of this unit may  
increase slightly.This is not a malfunction.  
• Be sure to unplug the AC power cord from the AC outlet before  
moving or carrying the unit.  
4
5
English  
Features  
INTRODUCTION  
DTV/TV/CATV  
You can use your remote control to select channels which are  
broadcast in digital format and conventional analog format.Also,  
cable subscribers can access their cableTV channels.  
Contents  
Information Display (ATSC only)  
You can display the title, contents and other information of the  
current DTV program on theTV screen.  
Important Safety Instructions  
Trademark Information  
Child Safety  
2
3
4
Autoprogram  
This unit automatically scans and memorizes channels available in  
your area, eliminating difcult setup procedures.  
INTRODUCTION  
Features  
5
6
6
6
6
7
7
8
9
Child Lock  
Supplied Accessories  
Symbols Used in this Manual  
Attaching the Base  
Mounting the Unit onYour Furniture  
Remote Control Function  
Installing the Batteries  
Control Panel  
This feature allows you to block children’s access to inappropriate  
programs.  
Closed Caption Decoder  
Built-in closed caption decoder displays text for closed caption  
supported programs.  
MTS/SAPTuner  
Audio can be selected from the remote control.  
Terminals  
Auto Standby  
If there is no input signal and no operation for 15 minutes, the  
unit will go into standby mode automatically.  
PREPARATION  
Antenna Connection  
10  
10  
10  
11  
Connection to Cable Receiver or Satellite Box  
Plug In the AC Power Cord  
Initial Setup  
SleepTimer  
You can set the unit to go into standby mode after a specic  
amount of time.  
Choices for On-screen Language  
Select your on-screen language:  
English, Spanish or French.  
WATCHINGTV  
Switching Each Input Mode  
SleepTimer  
12  
12  
12  
13  
13  
13  
14  
14  
Stereo Sound Function  
Sound Functions  
Freeze Mode  
TV Screen Display Mode  
Channel Selection  
TV Screen Information  
ECO  
PLL Frequency SynthesizedTuning  
Provides free and easy channel selection and lets you tune  
directly to any channel using the number and decimal point “ ”  
buttons on the remote control.  
Various Adjustment for Picture and Sound  
Customizes image quality suitable for your room and sets your  
sound preference.  
USING FUNCTIONS  
fun-Link via HDMI Link  
(HDMI Cable not Included)  
fun-Link allows your other HDMI link devices to be controlled by  
the HDMI cable connected to yourTV.  
Picture  
Sound  
Setup  
16  
16  
17  
18  
23  
24  
Features  
Language  
USB  
HDMI Input  
HDMI-DVI Input  
If your video device has DVI output jack, use an HDMI-DVI  
conversion cable to connect the unit.  
ComponentVideo Input  
PC Input  
CONNECTING DEVICES  
External Device Connection  
25  
USEFULTIPS  
FAQ  
AV Input  
USBTerminal  
28  
28  
Troubleshooting Guide  
The picture (JPEG) and video (Motion JPEG) les stored on a  
USB storage device can be played back on this unit.  
INFORMATION  
Glossary  
Digital Audio Output  
30  
30  
31  
31  
31  
33  
Maintenance  
<LC220EM2/LC190EM2 only>  
Headphone Audio Output  
General Specications  
Electrical Specication  
Other Specications  
Limited Warranty  
© 2011 Funai Electric Co., Ltd.  
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage  
medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of  
this manual or any revision hereto is strictly prohibited.  
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify  
any person or organization of such changes.  
with the  
design is a registered trademark of Funai Electric Co., Ltd. and may not be used in any way without the express written consent  
of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be  
construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or  
any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.  
6
Supplied Accessories  
Attaching the Base  
You must attach the base to the unit to have it as a table top  
unit. Be sure the front and rear of the base match the proper  
direction.At least 2 people are required for these steps.  
Owner’s Manual  
Quick Start Guide Registration card  
If you have any questions, please visit our website at  
www.emersonaudiovideo.com  
QSutickart  
1
Check the text “FRONT” with “arrow“ on the Base’s  
bottom to ensure it is being installed in the correct  
direction. Spread a thick and soft cloth over a table as shown  
at step 2. Place the main unit face down onto it. Make sure  
not to damage the screen.  
EN  
FR  
ES  
Installation  
Installation  
Instalación  
Remote  
Control  
(NH001UD)  
Batteries  
(AAA, 1.5V x 2)  
SOURCE  
TV base and 3 screws  
LC320EM2 M4 x 14  
LC220EM2/LC190EM2 M4 x 12  
2
Insert 2 hooks under the  
bottom of the main unit  
into base holes (shown by  
arrow ), then move the  
base in the direction as  
SLEEP  
FREEZE  
FORMAT  
shown by arrow until  
BACK  
ECO  
FRONT  
it stops and the screw  
holes are aligned.  
Make sure not to put the AC power cord between the  
MENU  
INFO  
SAP  
MUTE  
0
.
base and the unit.  
PREV CH  
3
Drive Phillips head screws  
into the 3 threaded holes  
at the bottom of the base  
until they are tight.  
Note  
If you lose the screws, please purchase the above-mentioned  
Phillips head screws at your local store.  
• If you need to replace these accessories, please refer to the part  
name or No. with the illustrations and call our toll free customer  
support line found on the cover of this manual.  
To remove the base from this unit  
• Unscrew the Phillips head screws in step 3  
After the screws are removed, pull the base up toward the rear of  
the unit. Be careful not to drop the base when you remove it.  
When using a universal remote control to operate this unit.  
• Make sure the component code on your universal remote control  
is set to our brand. Refer to the manual accompanying your  
remote control for more details.  
• We do not guarantee 100% interoperability with all universal  
remote controls.  
Note  
• When attaching the base, ensure that all screws are tightly fastened.  
If the base is not properly attached, it could cause the unit to fall,  
resulting in injuries as well as damage to the unit.  
• Make sure to use a table which can support the weight of this unit  
and is larger than this unit.  
• Make sure the table is in a stable location.  
• When attaching the base, ensure that “FRONT” with “arrow”  
written on the bottom of the base is downward. If it’s not  
downward, the 2 hooks don’t t into the base.  
Symbols Used in this Manual  
The following is the description for the symbols used in this  
manual. Description refers to:  
ATSC  
NTSC  
: DigitalTV operation  
Mounting the Unit onYour Furniture  
Screw this unit on your furniture tightly using wood screw (not  
supplied) in the hole at the back of the base as shown.  
:Analog/CableTV operation  
If neither symbol appears, the operation is applicable to  
both.  
• Recommended screw dimension : 3/16 x 3/4 inches(5.1 x 20 mm)  
rear of this unit  
screw hole  
Note  
• When you remove this unit make sure to unscrew the wood  
screw from your Wood Stand, Furniture and other wood item.  
7
English  
Remote Control Function  
1 SOURCE  
2 SLEEP  
p.12  
p.12  
p.14  
p.11  
p.15  
p.11  
p.12  
p.12  
p.13  
11  
SOURCE  
1
SLEEP  
BACK  
FREEZE  
FORMAT  
ECO  
3 BACK  
12  
13  
2
4 ///(cursor)  
5 MENU  
14  
3
4
6 OK  
OK  
7 VOL  
/
MENU  
INFO  
8 MUTE  
15  
16  
5
6
9 Number buttons  
(dot)  
SAP  
Press to shift the subchannel from the main channel.  
10 PREV CH p.13  
Press to return to previously viewed channel.  
(power) p.11  
VOL  
CH  
17  
7
8
MUTE  
11  
1
4
2
5
8
0
3
6
9
.
Press to turn the unit on and go into standby mode.  
To completely turn off the unit, you must unplug the AC  
power cord.  
9
12 FORMAT  
p.13  
Press to select aspect ratio available for theTV screen.  
7
13 FREEZE  
Press to freeze screen image.  
p.13  
p.14  
PREV CH  
10  
14 ECO  
Press to reduce power consumption.  
15 INFO  
16 SAP  
p.14  
p.12  
p.13  
17 CH/▼  
Installing the Batteries  
Install the batteries (AAA, 1.5V x 2) matching the polarity  
indicated inside battery compartment of the remote control.  
Battery Precautions:  
• Be sure to follow the correct polarity as indicated in the battery  
compartment. Reversed batteries may cause damage to the  
device.  
• Do not mix different types of batteries together (e.g.Alkaline and  
Carbon-Zinc, or rechargeable batteries like ni-cad, ni-mh, etc) or  
old batteries with fresh ones.  
• If the device is not to be used for a long period of time, remove  
the batteries to prevent damage or injury from possible battery  
leakage.  
• Do not try to recharge batteries; they can overheat and rupture.  
8
Control Panel  
1 VOLUME  
Press to adjust the volume up/down or move right  
)/left ( ) through the main menu items.  
/
p.12  
(
2 CHANNEL /▼  
p.13  
Press to select channels or move up ()/down ()  
through the main menu items.  
3 MENU  
p.15  
p.12  
p.11  
7
6
4 SOURCE  
5
POWER  
Press to turn the unit on and go into standby mode.  
To completely turn off the unit, you must unplug the AC  
power cord.  
6 Infrared sensor window  
Receives infrared rays transmitted from the remote  
control.  
VOLUME  
CHANNEL  
MENU  
SOURCE  
POWER  
7 Standby indicator  
Lights up red when the unit is in standby mode and  
ashes when the unit goes into standby mode.  
1
2
3
4
5
9
English  
Terminals  
Side Panel  
8 Component/CompositeVideo Input jacks  
32”  
22”/19”  
forVIDEO  
p.26  
CompositeVideo Input jack is shared jack with  
ComponentVideo Input (Y) jack.  
11  
12  
13  
9 Analog Audio (L/R) Input jacks  
p.10, 25, 26, 27  
8
9
Connect Analog Audio signals from  
ComponentVideo/Analog Audio (L/R) jacks signal or  
HDMI-DVI/Analog Audio (L/R) jacks signal or  
CompositeVideo/Analog Audio (L/R) jacks signal or  
PC Connection/Analog Audio (L/R) jacks signal with  
stereo mini plug conversion cable jack on PC.  
Analog Audio (L/R) Input jacks are right below the  
ComponentVideo Input jacks.When the Audio is  
monaural, then only connect to the Audio L Input jack.  
8
9
10  
14  
10  
10 Antenna Input jack  
p.10  
<LC320EM2 only>  
11 USB Terminal  
p.27  
Use this terminal only to play back the picture (JPEG) and  
video (Motion JPEG) les stored on a USB storage device.  
12 HDMI 2 Input jack  
p.10, 25  
<LC220EM2/LC190EM2 only>  
13 HDMI (HDMI-DVI) Input jack  
p.10, 25  
14 Headphone Audio Output jack  
Headphone connection for personal listening.  
Rear Panel  
15 AC power cord  
p.10  
p.26  
p.27  
15  
16 Digital Audio Output jack  
17 PC (VGA) Input jack  
32”  
22”/19”  
<LC320EM2 only>  
18 HDMI 1 (HDMI-DVI) Input jack  
HDMI1  
19  
16  
18  
p.10, 25  
p.27  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
<LC220EM2/LC190EM2 only>  
16  
17  
19 USB Terminal  
Use this terminal only to play back the picture (JPEG) and  
17  
video (Motion JPEG) les stored on a USB storage device.  
PC-IN  
RGB  
Note for USB terminal  
• User should not connect any devices to the USB terminal such as  
digital camera, keyboard, mouse, etc. (because these will not work).  
The software update is, in most cases, handled by an authorized  
service person or in some circumstances the user may be asked  
to do the software update themselves.  
10  
Connection to Cable Receiver or  
Satellite Box  
PREPARATION  
Use an HDMI or ComponentVideo cables to connect the  
HDMI or the ComponentVideo Input jacks of the unit to the  
HDMI or the ComponentVideo output jacks of the cable  
receiver/satellite box.  
No supplied cables are used with these connections:  
• Please purchase the necessary cables at your local store.  
If you connect to the unit’s ComponentVideo Input jacks,  
connect Analog Audio cables to the Analog Audio L/R Input  
jacks right below the ComponentVideo connector jacks.  
Before you connect:  
Be sure your antenna or other device is connected properly  
before plugging in the AC power cord.  
satellite dish  
cableTV signal  
including PPV  
or  
Antenna Connection  
Connect the RF coaxial cable on your home outlet to the  
antenna input jack of this unit.  
RF coaxial cable  
VHF/UHF  
analog  
*
HDMI cable  
or  
DTV antenna  
component video cables  
(red/blue/green) and  
audio cables  
(green) (blue) (red)  
AUDIO OUT  
COMPONENT VIDEO OUT  
Pb/Cb Pr/Cr  
HDMI OUT  
L
R
Y
or  
or  
ANT IN  
STEREO  
PCM  
RF coaxial cable  
cable receiver/satellite box  
For LC320EM2, you can also use the HDMI jack on the Rear Panel.  
*
You can also connect this unit to the cable receiver or satellite  
box other than the HDMI or the ComponentVideo output jacks  
or CompositeVideo output jack (  
have different output jacks.  
Required cables and connecting methods of the cable receiver/  
satellite box, or the availability channel for the clear QAM may  
differ depending on the cable/satellite provider or localTV  
broadcaster.  
p.26) because they might  
cableTV signal  
Once connections are completed, turn on the unit and begin  
initial setup. Channel scanning is necessary for the unit to  
memorize all available channels in your area. [Initial Setup]  
For more information, please contact your cable/satellite provider  
or localTV broadcaster.  
Note  
p.11  
Note  
• If you have any question about the DTV’s antenna, visit  
• Use an HDMI cable with the HDMI logo (a certied HDMI cable).  
• Depending on your antenna system, you may need different types  
of combiners (mixers) or separators (splitters) for HDTV signal  
the minimum RF bandpass on these devices is 2,000MHz or 2GHz.  
• For your safety and to avoid damage to this unit, please unplug the  
RF coaxial cable from the antenna input jack before moving the  
unit.  
• If you did use an antenna to receive analogTV, it should also  
work for DTV reception. Outdoor or attic antennas will be more  
effective than a set top or inside antenna.  
To switch your reception source easily between antenna and cable,  
install an antenna selector.  
• If you are not receiving a signal from your cable service, contact the  
Cable provider.  
High Speed HDMI cable is recommended for the better compatibility.  
Plug In the AC Power Cord  
Make sure that the AC power cord must be plugged to an AC  
outlet after all the necessary connections are made.  
Caution:  
• Do not connect the AC power cord to a power supply outside  
the indicated voltage of this unit (AC 120V).  
Connecting the AC power cord to a power supply outside of this  
range may result in re or electrical shocks.  
Note  
• Each time you plug in the AC power cord, no operations will be  
performed for a few seconds.This is not a malfunction.  
11  
English  
4
Use /to select the desired location setting, then press  
OK  
These operations are accessible by remote control.  
Some may also be accessible by controls on the main unit.  
Initial Setup  
Select “Retail” or “Home” for your location.  
Initial Setup  
This section will guide you through the unit’s initial setting  
which includes selecting a language for your on-screen menu  
and autoprogram, which automatically scans and memorizes  
viewable channels.  
Home  
OK  
Retail  
Select  
Before you begin:  
Make sure the unit is connected to antenna or cable.  
• Select [Retail] store, the unit will be set up with  
predefined setting for retail displays.  
1
After making all the necessary connections,  
press to turn on the unit.  
• Select [Home], the unit is set to maximize the energy  
efficiency for home setting and it can be adjusted  
through a choice of picture and sound quality according  
to your preference. Use this setting to remove the  
• It may take a few moments to turn on the unit for the  
first time.  
[Initial Setup] menu appears automatically after the  
unit is turned on.  
E-Sticker if visible from the display.  
p.23  
• When the initial setup is completed, the lowest  
memorized channel with the confirmation message of  
the location setting will be displayed on theTV screen.  
2
3
Use /to select the on-screen language from the  
choices (English/Español/Français) on the right side of the  
TV screen, then press OK  
You must set [Home] in step 4. Otherwise, [Picture]  
and [Sound] settings you adjusted will not be  
memorized after the unit goes into standby mode.  
Use /to select [Antenna] forTV channels or [Cable]  
for CATV channels, then press OK  
Note  
• If you are not receiving a signal from your cable service, contact  
the Cable provider.  
If you press or MENU during autoprogram, this setup of TV  
channels will be canceled.  
• The initial autoprogram function can be executed for either  
[Antenna] or [Cable] only once.When you change the  
Initial Setup  
Antenna  
Make sure the antenna is connected to ''ANT. IN'' jack.  
Cable  
Skip  
Select your signal source.  
connection (Antenna/Cable), set [Autoprogram] again.  
• If there is no signal input from the antenna terminal and no  
p.17  
Antenna  
Cable  
Or  
ANT.IN  
operation for several seconds after you turn on the unit, helpful  
hints appears. Follow the instructions listed on theTV screen.  
Select  
OK  
Back  
Skip  
Initial Setup  
[Autoprogram] will begin.  
Retry  
Later  
No channel is registered.  
Try Autoprogram again?  
Initial Setup  
Verify that you have a cable connected to the "ANT. IN" jack  
on the back of the TV, the channel installation process  
searches this connection. If you are using a cable or satellite  
box, please confirm the input which you have connected to the  
box and press “SOURCE” key on the remote control to select  
the appropriate source input.  
Please wait while the system is scanning for channels.  
Auto programming may take more than 20 minutes to  
complete.  
0%  
Digital channels  
Analog channels  
0 ch  
0 ch  
Select  
OK  
Skip  
After an initial setup is completed...  
• If you want to scan the channels automatically again.  
[Autoprogram] p.17  
Skip  
You can add the desired cable and analog channels  
unmemorized by autoprogram.  
[Add Channels]  
• If you want to change to another language.  
[Language] p.23  
• If you want to change the location setting.  
[Location] p.23  
p.18  
12  
WATCHINGTV  
Switching Each Input Mode can easily switch with the remote control  
betweenTV (ATSC or NTSC) and external devices when they are connected to the unit.  
Press SOURCE or CHrepeatedly to cycle through the input modes.  
1
e.g.)  
Source  
11.1  
HDMI1  
Video  
HDMI2  
T
H
H
V
D
D
M
I
I
1
2
1
2
DTV/TV channel  
*
*
M
SOURCE  
FREEZE  
Video  
P
C
PC  
Component  
or  
SLEEP  
BACK  
FORMAT  
ECO  
Pressing CHreverses the direction of the input modes.  
1These may differ depending on what product you purchased. For example,  
LC220EM2 and LC190EM2 will be displayed [HDMI] instead of [HDMI 1]  
[HDMI 2]  
2[Component] will be displayed if you connected component video cables  
to this unit.  
*
*
OK  
SleepTimer  
MENU  
INFO  
can set the unit to go into standby mode after an incremental period of time.  
Press SLEEP repeatedly to change the amount of time (increases  
Sleep  
120min.  
the time by 30 minutes up to 120 minutes).  
SLEEP once to call up the display for checking the remaining time.  
SAP  
To cancel sleep timer, press SLEEP repeatedly until [Sleep Off] is  
displayed.  
VOL  
CH  
MUTE  
Sound Functions describe how to change the audio or the audio language as  
well as the volume.  
1
4
2
5
8
0
3
6
9
.
Volume Adjustment  
Use VOL  
/
to adjust the volume.  
Volume  
30  
will be displayed for a few seconds when adjusting the volume.  
7
Silence Mode  
Press MUTE to turn off the sound temporarily.  
PREV CH  
Mute  
will be displayed for a few seconds.  
Press MUTE again or VOL  
volume.  
/
to recover the original  
Switching Audio Mode  
ATSC  
Press SAP repeatedly to cycle through the available audio languages.  
• Available languages differ depending on the broadcast.  
[Other] is displayed when the audio language cannot be  
acquired, or the acquired languages are other than English,  
Spanish or French.  
11.1  
English 1/3  
NTSC  
SAP to display the currently selected audio mode.  
While receiving an MTS broadcast, press repeatedly to cycle through  
the available audio channel.  
11  
SAP / STEREO  
e.g.) When all audio are available  
STEREO : Outputs stereo-audio  
SAP : Outputs second audio program  
MONO : Outputs mono-audio  
SAP / STEREO  
SAP / MONO  
SAP / STEREO  
13  
English  
Freeze Mode can freeze the image shown on theTV screen for 5 minutes.  
Press FREEZE to freeze the image.  
Freeze  
The sound output will not be paused.  
To cancel freeze mode, press any buttons except y  
TV Screen Display Mode  
5 types of display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal.And 3 types of display  
modes can be selected for PC input signal.  
Press FORMAT  
repeatedly to switch theTV aspect ratio.  
Normal displays a 16:9 picture at its original size.  
For 16:9 video signal  
4:3 displays a 16:9 picture at a 4:3 size; the picture  
is shortened horizontally. Sidebars appear on both  
edges of the screen.  
Movie expand displays a 16:9 picture that is  
vertically stretched to ll the screen.This only crops  
out the top of the picture.  
Normal  
4:3  
Movie expand  
Zoom displays a 16:9 picture at its maximum size  
without changing its horizontal and vertical ratio.  
Wide displays a horizontally stretched picture.This  
crops out the left and right sides of the picture  
Wide  
Zoom  
Normal displays a 4:3 picture at its original size.  
Sidebars appear on both edges of the screen.  
For 4:3 video signal  
16:9 displays a 4:3 picture at a 16:9 size; the picture  
is stretched horizontally to ll the screen.  
Movie expand displays a 4:3 picture at a 16:9 size;  
the picture is stretched more vertically at the top of  
the screen.This crops out the top of the picture.  
Normal  
16:9  
Movie expand  
Zoom displays a 4:3 picture at a 16:9 size; at its  
maximum size that is more vertically stretched to  
ll the screen.This crops out the top and bottom of  
the picture.  
Wide  
Zoom  
Wide displays the picture with its center at the  
original size and the edges stretched horizontally to  
ll the screen.  
Normal displays a proportionately stretched  
picture. Sidebars appear on both edges of the screen.  
For PC input signal  
Full displays a picture that is stretched out of  
proportion horizontally to ll the screen.  
Unscaled displays a picture in its original size.  
Normal  
Full  
Unscaled  
Channel Selection  
Select channels by using CH/or the Number buttons  
To select the memorized channels, use CH/or the Number buttons.  
To select the non-memorized channels, use the Number buttons.  
11.1  
To use the Number buttons  
ATSC  
NTSC  
When selecting cable or analog channel 11  
When selecting digital channel 11.1  
Be sure to press before entering the subchannel number.  
OK  
1
1
OK  
1
1
.
1
PREV CH to return to the previously viewed channel.  
[No Signal] will appear on theTV screen after the subchannel broadcast is over.  
[Audio only program] message will appear on theTV screen, when you receive only sound signal.  
Note  
14  
TV Screen Information  
ECO  
You can display the currently selected channel or other  
information such as the audio mode on theTV screen.  
In the digital mode, the detailed broadcasting information  
for the current off the air channel such as program title and  
program guides are displayed.  
You can turn on ECO Mode to conserve power.  
Press ECO once to turn on ECO Mode and reduce  
power consumption.  
Press ECO again to turn off ECO Mode.  
ECO  
Off  
ECO  
On  
1
Press INFO  
ATSC  
On  
Off  
Reduces power consumption  
Sets the backlight brighter.  
1
2
3
4
A
A
Day of Memories  
KABC  
Note  
11.1  
English 1/2  
5
quarter-century ago,which may now qualify as the  
You must set [Home] in [Location]. p.23  
Otherwise, the settings you adjusted will not be saved when the  
unit goes into standby mode.  
good old days of newspapering,run-of-paper sales  
accounted for 80 percent of the industry's advertising  
revenues.Department stores and supermarket were  
1080i HD  
16:9  
6, 7, 8  
CC  
Rating  
TV: TV-14  
9
10  
NTSC  
4
5
SAP / STEREO  
6, 7, 8  
9
10  
1
2
program title  
program guide  
(The program guide added to broadcasting  
information is displayed to a maximum of 4 lines.)  
broadcast station  
channel number  
3
4
5
audio language (ATSC)/audio mode (NTSC)  
[Switching Audio Mode]  
effective scanning lines and scan mode  
TV format  
p.12  
6
7
8
9
program’s image aspect ratio  
CC (not available if closed caption is set to [Off])  
10 child lock rating  
2
Press INFO or BACK to hide the information.  
Note  
• When the program guide consists of more than 4 lines, use /▼  
to scroll to the next/previous lines.  
[No description provided.] is displayed when the program guide  
is not provided.  
• While the program guide is displayed, the closed caption function  
is interrupted.  
• In external input mode, the following screen is displayed;  
e.g.) When an external device is connected toVideo Input jack.  
Video  
480i SD  
CC  
TV-PG DLSV  
• The information display will automatically disappear in 1 minute  
15  
English  
USING FUNCTIONS  
This section describes the overview of the main menu  
displayed when you press MENU  
The main menu consists of the function setting items below.  
1
Press MENU to display  
the main menu.  
2
Use /to select a desired menu and an item, then  
press OK to determine the setting.  
SOURCE  
FREEZE  
SLEEP  
BACK  
FORMAT  
ECO  
Picture  
Sound  
Setup  
Picture  
Page 16  
Adjusting the picture mode, or customize the  
picture quality as your preference.  
OK  
MENU  
INFO  
Features  
Language  
USB  
SAP  
Sound  
Page 16  
VOL  
CH  
MUTE  
Adjusting the sound mode, equalizer and some  
other sound functions.  
1
4
2
5
8
0
3
6
9
.
Setup  
Page 17  
Scanning the channels available in your area and  
see what the antenna levels are.  
7
PREV CH  
Features  
Page 18  
Adjusting the Closed Caption, parental guide and  
some other useful functions.  
Language  
Page 23  
You can choose English, Spanish, or French  
as your on-screen language.  
USB  
Page 24  
You can view picture (JPEG) and video (Motion  
JPEG) les stored on a USB storage device.  
3
When the setting is completed, press MENU to exit.  
16  
Picture  
Sound  
Before you begin:  
You must set [Home] in [Location]  
Before you begin:  
You must set [Home] in [Location]  
p.23  
p.23  
Otherwise, the settings you adjusted will not be memorized  
after the unit goes into standby mode.  
Otherwise, the settings you adjusted will not be memorized  
after the unit goes into standby mode.  
1
Use /to select the item you want to adjust, then press  
OK  
1
Use /to select the item you want to adjust, then press  
OK  
Picture  
Picture  
Sound  
Picture  
Smart Picture  
Brightness  
Contrast  
Smart Sound  
Personal  
Standard  
Sound  
Setup  
Sound  
Setup  
Equalizer  
30  
60  
36  
0
Virtual Surround Sound  
Auto Volume Leveling  
TV Speakers  
On  
Color  
Off  
Tint  
On  
Features  
Language  
USB  
Features  
Language  
USB  
Sharpness  
Color Temperature  
Noise Reduction  
Primary MTS  
0
Stereo  
Normal  
On  
2
Adjust the following items.  
2
Adjust the following items.  
Smart Picture  
Smart Sound  
Use /to select the desired setting, then press OK  
([Personal] [Standard] [Movie] [Music], and [News])  
Use /to select the desired setting, then press OK  
([Personal] [Standard] [Sports] [Movie], and [Game])  
Equalizer  
Adjust tonal quality for each frequency.  
Brightness, Contrast, Color, Tint, Sharpness,  
ColorTemperature  
You can only adjust the following options when you set to  
Use /to select the specic frequency and use /to  
adjust the level, then press OK  
[Personal] in [Smart Picture]  
Use /to select the desired setting, then press OK.Then  
use /to adjust the setting.  
Virtual Surround Sound  
Cursor  
Cursor ►  
Virtual surround sound gives you the stereophonic virtual  
space through your existing 2-channel stereo system.  
Brightness  
Contrast  
to decrease brightness to increase brightness  
to decrease contrast  
to increase contrast  
Use /to select the desired option, then press OK  
to decrease color  
intensity  
to increase color  
intensity  
Color  
On  
Off  
Emphasized effect.  
Natural effect.  
Tint  
to add red  
to soften  
to add green  
to sharpen  
Sharpness  
Color  
Temperature  
to add warm colors  
to add cool colors  
AutoVolume Leveling  
This function keeps a constant loudness differential between  
theTV commercials and the programs.  
Noise Reduction  
Use /to select the desired option, then press OK  
Reduces the noise of the picture.  
Reduces volume differences between the  
TV commercials and the programs.  
On  
Use /to select the desired option, then press OK  
Off  
Removes the auto volume leveling.  
On  
Off  
Reduces noise in an image.  
Sets noise reduction to off.  
Note  
• This function is disabled when PC input is selected. (Setting will be  
in gray.)  
17  
English  
TV Speakers  
Autoprogram  
If you switch wires (e.g. between antenna and CATV) or if you  
move the unit to a different area after the initial setting, or if  
you restore the DTV channels you deleted, it is recommended  
to use Autoprogram to perform a new channel search.  
amplier is HDMI link function compatible and connected by  
an HDMI cable to this unit, some sound operations such as  
volume up can be changed by using this unit’s remote control.  
Make sure [fun-Link Control] is set to [On]  
p.22  
1
2
Use /to select [Autoprogram], then press OK  
Use /to select the desired option, then press OK  
Use /to select an appropriate option, then press OK  
On  
The sound will be output from the unit’s speakers.  
Autoprogram  
Picture  
The sound will not be output from the unit’s  
speakers.  
Off  
Back  
Auto program will rescan all channels.  
You can control audio output from your  
connected HDMI link devices by using this unit's  
remote control.  
Sound  
Setup  
Auto programming may take more than 20  
minutes to complete.  
Select your signal source.  
Antenna  
Cable  
Ext. Amp  
Antenna  
Features  
Language  
USB  
Note  
• We do not guarantee 100% interoperability with other brands of  
HDMI link compliant devices.  
[Unmute] may be displayed on theTV screen when you recover  
the volume from your amplier.  
Cable  
Or  
ANT.IN  
• When connected toVHF/UHF antenna, select [Antenna]  
• When connected to CATV, select [Cable]  
[Autoprogram] will begin.  
Primary MTS  
You can set the output mode as a default for the sound mode  
(NTSC only).  
This setting is not interlocked when you change the output  
Please wait while the system is scanning for channels.  
Auto programming may take more than 20 minutes to  
complete.  
mode by pressing SAP. [Sound Functions]  
p.12  
75%  
Use /to select the desired option, then press OK  
Digital channels  
Analog channels  
10 ch  
6 ch  
Stereo  
Mono  
SAP  
Outputs stereo-audio.  
Outputs mono-audio.  
Outputs second audio program.  
Exit  
• When the scanning and memorizing are completed, the  
lowest memorized channel will be displayed.  
Setup  
Note  
• After setting [Autoprogram], using CH/on the remote  
control skips unavailable programs automatically.  
• If you are not receiving a signal from your cable service, contact  
the Cable provider.  
Before you begin:  
Make sure the unit is connected to antenna or cable.  
• If you press or MENU during autoprogram, the setup ofTV  
channels will be canceled.  
• Even if [Autoprogram] is completed, the channel setting will be  
lost if the AC power cord is unplugged before the unit goes into  
standby mode by pressing  
1
Use /to select the item you want to adjust, then press  
OK  
Setup  
Picture  
• The PIN code will be required once you set a PIN code in the  
Autoprogram  
[Child Lock]  
p.20  
Sound  
Setup  
Channel List  
Add Channels  
Antenna  
• If you want to change your PIN code, follow the instruction of  
[Change PIN] p 21  
Features  
Language  
USB  
2
Adjust the following items.  
18  
Channel List  
The channels selected here can be skipped when selecting the  
Antenna Conrmation  
ATSC  
channels using CH/▼  
Those channels can still be selected with the Number buttons  
This function lets you check the digital signal strength of each  
channel.  
1
2
Use /to select [Channel List], then press OK  
1
2
Use /to select [Antenna], then press OK  
Use /to select the channel you want to remove, then  
press OK  
Use the Number buttons or CH/to select the  
channel for which you want to check the digital signal  
strength.  
Channel List  
Picture  
DTV  
DTV  
6.1  
8.1  
9
11.1  
Sound  
Setup  
Highlight channels for  
Ch Up / Down key selection.  
Antenna  
27  
Picture  
Sound  
Setup  
DTV  
DTV  
48.1  
58  
Features  
Language  
USB  
Back  
67.1  
Ch Select  
Watch/Skip  
Back  
Current 50 Max  
50  
Features  
Language  
USB  
The channel display for the removed channel darkens.  
You will not be able to select the channel again using  
CH/▼  
Ch Change  
To reactivate a removed channel, use /and press  
OK.The registered channels are highlighted.  
• When you remove a main channel, its subchannels are  
removed as well.  
Note  
• If the channel is set to analog channel or external input, you  
cannot conrm the antenna condition.  
Note  
• The channel with the [DTV] indicated on the display is ATSC.  
Otherwise the channel is NTSC.  
Features  
Add Channels  
1
Use /to select the item you want to adjust, then press  
OK  
This function lets you add the off the air along NTSC or analog  
Cable channels that were not added by the autoprogram due  
to reception conditions at the initial setting.  
Features  
Picture  
Closed Caption  
Sound  
Setup  
Child Lock  
1
2
Use /to select [Add Channels], then press OK  
ECO  
On  
PC Settings  
fun-Link (HDMI CEC)  
Location  
Use the Number buttons to enter the number of the  
channel you want to add, then press OK  
Features  
Language  
USB  
Home  
E-Sticker  
− −  
11  
Current Software Info  
Add Channels  
Picture  
Sound  
Setup  
2
Adjust the following items.  
Add Channels  
For analog channels, select a  
channel to be added using  
number keys.  
For digital channels, you must  
perform Autoprogram function.  
Features  
Language  
USB  
Ch Change  
Back  
Note  
• If setup completes successfully, [Added to the channel list.] is  
displayed.  
• If external input is used, it is not possible to register the channel  
and [Unavailable] will be displayed on theTV screen.  
• By using CH/, you can select the memorized channels only.  
19  
English  
Closed Caption  
Note  
[Digital Caption Service] that you can switch differs depending on  
the broadcast description.  
movies and news. Closed caption refers to text of dialog or  
descriptions displayed on-screen.  
C. Caption Style  
ATSC  
Use /to select [Closed Caption], then press OK  
See the following description for setting each item.  
Closed Caption  
Picture  
You can change the caption style such as font, color or size,  
etc.  
Caption Service  
Digital Caption Service  
Caption Style  
Off  
Off  
A
B
C
Sound  
Setup  
1
2
3
4
Use /to select [Caption Style], then press OK  
Features  
Language  
USB  
Use /to select [User Setting], then press OK  
Use /to select [On], then press OK  
Use /to select an item, then press OK. Then use  
/to select the desired setting and press OK  
A. Caption Service  
Picture display  
1
2
Use /to select [Caption Service], then press OK  
Use /to select the desired closed caption, then press  
OK  
So, you must be Philip. Hi!  
I’m pleeased tto mmeeeett you.  
Off  
Select if you do not want caption service.  
Edge  
The primary caption and text services.The  
captioning or text is displayed in the same language  
(Edge Color and EdgeType)  
Font  
CC-1 andT-1 as the program’s dialog (up to 4 lines of script on the  
TV screen, where it does not obstruct relevant parts  
of the picture).  
(Font Style, Font Size, Font Color and Font Opacity or  
Transparency)  
Background  
Serve as the preferred data channels.  
CC-3 andT-3 The captioning or text is often a secondary  
language.  
(Background Color and Background Opacity or  
Transparency)  
• Review your setting choice made below by looking in  
the upper right corner of the displayed setting box (not  
all selections show the differences selected).  
Rarely available and broadcasters use them only in  
CC-2, CC-4,  
special conditions, such as when [CC-1] and [CC-3]  
T-2 andT-4  
or [T- 1 ] and [T- 3 ] are not available.  
• There are 3 display modes according to programs:  
Font Style  
Paint-on  
mode  
Displays input characters on theTV screen  
immediately.  
Font Size  
Closed captioning font style, size,  
Font  
Font Color  
color and opacity can be changed.  
Once characters are stored in memory, they are  
displayed all at once.  
Pop-on mode  
Roll-up mode  
Font  
Opacity  
Displays the characters continuously by scrolling  
(max. 4 lines).  
Background  
Color  
Background color and opacity of the  
displayed caption can be switched.  
Background  
Background  
Opacity  
B. Digital Captiioon SSeerrvice  
ATSC  
Edge Color  
EdgeType  
Edge color and type of the displayed  
caption can be switched.  
Edge  
In addition to the basic closed caption, DTV has its own closed  
caption called digital caption service. Use this menu to change  
the settings for digital caption service.  
1
2
Use /to select [Digital Caption Service], then press  
OK  
Use /to select the desired digital caption service, then  
press OK  
Select if you do not want digital caption  
service.  
Off  
Select one of these before changing any  
CS-1 to CS-6  
other item in [Closed Caption] menu.  
Choose [CS-1] under normal circumstances.  
20  
Note  
Child Lock  
Picture  
Sound  
Setup  
• Closed caption will not be displayed when you are using an HDMI  
connection.  
To show the closed caption on yourTV screen, broadcast signal  
must contain the closed caption data.  
• Not allTV programs and commercials have the closed caption or  
all types of the closed caption.  
• Captions and texts may not exactly match theTV voice.  
• Changing channels may delay the closed caption for a few seconds.  
• Adjusting or muting the volume may delay the closed caption for  
a few seconds.  
Channel Lock  
A
B
C
US Movie Ratings Lock  
US TV Ratings Lock  
Canadian English Rating  
Canadian French Rating  
Region Ratings Lock  
Clear Region Ratings Lock  
Change PIN  
Features  
Language  
USB  
D
• Abbreviations, symbols and other grammatical shortcuts may be  
used in order to keep pace with the on-screen action.This is not  
a malfunction.  
• The caption or text characters will not be displayed while the  
main menu or functions display is shown.  
• If a black box appears on theTV screen, this means that the closed  
caption is set to the text mode.To clear the box, select [CC-1]  
[CC-2] [CC-3] [CC-4] or [Off]  
Note  
• When you select a rating and set it to [Block], the higher ratings  
will be blocked automatically.The lower ratings will be available for  
viewing.  
• When you set the highest rating to [View], all ratings turn to  
[View] automatically.  
To block any inappropriate programs, set your limits in [US Movie  
Ratings Lock] [USTV Ratings Lock] and [Region Ratings Lock]  
• The child lock setting will be retained after a power failure or after  
the power is removed for longer than 10 seconds (except the PIN  
• If the unit receives poor quality television signals, the captions may  
contain errors, or there might be no captions at all. Some possible  
causes of poor quality signals are:  
- Automobile ignition noise  
- Electric motor noise  
code reverts to 0000). [Child Lock]  
p.20  
• If the rating is blocked, will appear.  
- Weak signal reception  
[Region Ratings Lock] will be available when the unit receives a  
digital broadcast using the new rating system.  
• For the United States, the unit may download the Region Ratings  
LockTable, if required.  
• The Canadian rating systems on this unit are based on CEA-766-A  
and CRTC policy.  
- Multiplex signal reception (ghosts or screen utter)  
- Data dropout and Pixelation (for DTV only)  
• The unit retains the closed caption setting if the power fails.  
• When the unit receives special effects playback signal (e.g. Search,  
Slow and Still) from aVCR’s video output channel (ch3 or ch4),  
the unit may not display the correct caption or text.  
A. Channel Lock  
Particular channels or external input modes can be invisible in  
this function.  
Child Lock  
Child lock reads the ratings for programs, then denies access  
to the programs which exceed the rating level you set.With  
this function, you can block certain programs inappropriate  
for children and any channels or external input modes can be  
invisible.  
1
2
Use /to select [Channel Lock], then press OK  
Use /to select the desired rating, then press OK  
repeatedly to switch between [View] and [Block]  
1
Use /to select [Child Lock], then press OK  
Features  
Picture  
Channel Lock  
Picture  
Closed Caption  
HDMI1  
1
Sound  
Setup  
Child Lock  
Sound  
Setup  
HDMI2  
Video  
ECO  
On  
2
PC Settings  
fun-Link (HDMI CEC)  
Location  
PC  
40.1 DTV  
40.2 DTV  
40.3 DTV  
Features  
Language  
USB  
Features  
Language  
USB  
Home  
E-Sticker  
− −  
Current Software Info  
Select  
View/Block  
Back  
1 These may differ depending on what product you purchased. For  
example, LC220EM2 and LC190EM2 will be displayed [HDMI]  
instead of [HDMI 1] [HDMI 2]  
2
Use the Number buttons to enter the 4-digit numbers for  
your PIN code.  
2 [Component] will be displayed if you connected component  
video cables to this unit.  
*
Setup  
Enter PIN.  
- - - -  
Features  
B. Setting US Movie ratings  
US Movie ratings lock is the rating system created by MPAA.  
• When you have not set up your PIN code,  
enter 0 0 0 0  
• When the PIN code is correct, [Child Lock] menu is  
displayed.  
1
2
Use /to select [US Movie Ratings Lock], then press  
OK  
See the following description for setting each item.  
Use /to select the desired rating, then press OK  
repeatedly to switch between [View] and [Block]  
21  
English  
US Movie Ratings Lock  
X
US TV Ratings Lock  
Picture  
Sound  
Setup  
Picture  
Sound  
Setup  
FV  
V
S
L
D
NC-17  
TV-MA  
TV-14  
TV-PG  
TV-G  
R
PG-13  
PG  
G
Features  
Language  
USB  
Features  
Language  
USB  
TV-Y7  
TV-Y  
NR  
Select  
View/Block  
Back  
Select  
View/Block  
Back  
Sub Rating  
FV  
Category  
Rating  
TV-Y7  
Rating  
Category  
FantasyViolence  
X
Mature audience only  
V
S
Violence  
NC-17  
No one under 17 admitted  
TV-MA  
TV-14  
TV-PG  
Sexual Situation  
Coarse Language  
Suggestive Dialog  
Restricted; under 17 requires accompanying  
parent or adult guardian  
R
L
PG-13  
PG  
Unsuitable for children under 13  
Parental guidance suggested  
General audience  
D
TV-14,TV-PG  
Note  
G
• Blocked sub rating will appear beside the main rating category in  
[USTV Ratings Lock] menu.  
NR  
No rating  
You cannot block a sub rating (D, L, S orV) if the main rating is set  
to [View]  
• Changing the category to [Block] or [View] automatically changes  
all its sub ratings to the same ([Block] or [View]).  
C. SettingTV ratings  
1
2
Use /to select [USTV Ratings Lock], then press OK  
D. Change PIN  
Although the default PIN code (0000) is supplied with the unit,  
you can set your own PIN code.  
Use ///to select the desired rating, then press  
OK repeatedly to switch between [View] and [Block]  
US TV Ratings Lock  
Picture  
FV  
V
S
L
D
Sound  
Setup  
1
2
Use /to select [Change PIN], then press OK  
TV-MA  
TV-14  
TV-PG  
TV-G  
Press the Number buttons to enter the new 4-digit PIN  
code.  
• Enter PIN code again in [Confirm PIN.] entry field.  
Features  
Language  
USB  
TV-Y7  
TV-Y  
Change PIN  
Picture  
Select  
View/Block  
Back  
Sound  
Rating  
TV-MA  
Category  
Enter PIN.  
- - - -  
Setup  
Mature audience only  
higher  
Confirm PIN.  
- - - -  
Features  
TV-14  
TV-PG  
TV-G  
Unsuitable for children under 14  
Parental guidance suggested  
General audience  
Language  
USB  
PIN Code  
Back  
Appropriate for all children 7 and  
older  
TV-Y7  
TV-Y  
Note  
• Make sure new PIN code and conrm PIN code must be exactly  
the same. If they are different, the space is cleared for reentering.  
Your PIN code will be erased and returns to the default PIN code  
(0000) when a power failure occurs.  
• If you forget the PIN code, unplug the AC power cord then wait  
for 10 seconds to plug the AC power cord in again.  
Appropriate for all children  
lower  
To set the sub ratings  
As forTV-MA,TV-14,TV-PG, orTV-Y7, you can further set the  
sub ratings to block specic elements of programming.To set  
the sub ratings, follow the step below.  
The unit will restore the PIN code to 0000 as the factory default.  
Use ///to select the desired rating, then press OK  
repeatedly to switch between [View] and [Block]  
22  
Clock, Phase  
ECO  
Use /to adjust [Clock] setting to stabilize the PC screen  
and [Phase] setting to improve the clarity of the PC screen.  
You can turn on ECO Mode to conserve power.  
1
2
Use /to select [ECO], then press OK  
Cursor ◄  
Cursor ►  
Clock  
Phase  
to decrease setting  
value  
to increase setting  
value  
Use /to select the desired mode, then press OK  
On  
Reduces power consumption  
Sets the backlight brighter.  
Off  
Note  
You may not obtain an appropriate screen with  
[Auto Adjustment] for some signals. In this case, adjust the settings  
manually.  
• Adjust [Phase] setting after [Clock] setting has been properly  
adjusted.  
Note  
You must set [Home] in [Location]. p.23  
Otherwise, the settings you adjusted will not be saved when the  
unit goes into standby mode.  
You can also press ECO directly to switch the desired setting.  
p.14  
fun-Link (HDMI CEC)  
This function allows you to operate the linked functions  
between our brand devices with a fun-Link feature and this  
unit connecting through an HDMI cable.  
PC Settings  
This function lets you adjust the PC screen position, clock and  
phase during PC input.  
1
Use /to select [fun-Link (HDMI CEC)], then press  
OK  
1
2
Use /to select [PC Settings], then press OK  
Use /to select the setting you want to adjust, then  
press OK  
fun-Link (HDMI CEC)  
Picture  
fun-Link Control  
Auto Device Off  
Auto TV On  
On  
On  
On  
PC Settings  
Picture  
Auto Adjustment  
Sound  
Sound  
Setup  
Device List  
Horizontal Position  
Vertical Position  
Clock  
0
0
0
0
Setup  
Features  
Language  
USB  
Features  
Language  
USB  
Phase  
2
3
Use /to select the desired setting, then press OK  
3
Adjust the following items.  
Adjust the following items.  
Auto Adjustment  
Use /to select [Adjust], then press OK.  
fun-Link Control  
Set the fun-Link [On] or [Off]  
The following additional settings will be grayed out when you  
set to [Off]  
Auto Adjustment  
Picture  
Cancel  
Adjust  
Sound  
To automatically synchronize  
the phase and clock  
on the TV and PC.  
Use /to select the desired setting, then press OK  
Setup  
Selects if you have connected an external device  
On  
Features  
Language  
USB  
that is compatible with the fun-Link function.  
Off  
Disables all fun-Link.  
Auto Device Off  
You can set your device to turn off by interlocking from this  
unit’s power.  
• The horizontal/vertical position, clock and phase of the  
PC screen are automatically adjusted.  
Use /to select the desired setting, then press OK  
Your connected fun-Link device turns off  
automatically when the unit goes into standby  
mode.  
Horizontal Position,Vertical Position  
On  
Off  
Use /to adjust.  
Cursor ◄  
Cursor ►  
Your connected fun-Link device stays on even if  
the unit goes into standby mode.  
Horizontal  
Position  
to move PC screen left to move PC screen right  
to move PC screen  
to move PC screen up  
down  
Vertical  
Position  
23  
English  
AutoTV On  
E-Sticker  
This unit will turn on when the power on signal is sent from  
your connected fun-Link device.  
When you select [Location] to [Retail] store, E-Sticker  
(Electronic Sticker) is displayed.  
E-Sticker can be turned Off using procedure below.  
Use /to select the desired setting, then press OK  
This unit turns on automatically when you turn on  
your connected fun-Link device.  
On  
1
2
Use /to select [E-Sticker], then press OK  
This unit stays in standby mode even if you turn on  
Off  
Use /to select [Off], then press OK  
your connected fun-Link device.  
Off  
You can turn off E-Sticker.  
Device List  
Top  
E-Sticker is displayed on top of theTV screen.  
This function lets you see the product model number or name  
of connected devices.  
Bottom  
E-Sticker is displayed on bottom of theTV screen.  
Device List  
Picture  
Note  
• If you select [Home], E-Sticker will not be displayed.  
NB620SL2  
MBP5230  
HDMI1  
HDMI2  
Sound  
Setup  
Current Software Info  
This function shows what version of the software currently  
used.  
Features  
Language  
USB  
Refresh  
Back  
1
2
Use /to select [Current Software Info], then press  
OK  
These may differ depending on what product you purchased. For  
example, LC220EM2 and LC190EM2 will be displayed [HDMI]  
instead of [HDMI 1] [HDMI 2]  
*
Conrm the version of the software currently used.  
Current Software Info  
Picture  
Location  
Back  
Sound  
You must set [Home] in this setting. Otherwise, [Picture] and  
[Sound] settings you adjusted will not be memorized after you  
turn off the unit.  
Release Version:  
Setup  
XXXXXXX_XX_XX_XXXX_XX  
Features  
Language  
USB  
1
2
Use /to select [Location], then press OK  
Use /to select the desired location, then press OK  
The unit will be set up with predefined settings  
Retail  
for retail displays. In this setting, you can set the  
backlight brighter.  
Language  
The unit is set to maximize the energy efficiency  
for home setting and it can be adjusted through a  
choice of picture and sound quality according to  
your preference.  
Home  
Use
/
to select
[English] [Español]
 
or
[Français]
, then  
press OK  
Language  
Picture  
Select your menu language.  
English  
Español  
Sound  
Setup  
Seleccione el idioma para el menú.  
Sélectionnez la langue du menu.  
Français  
Features  
Language  
USB  
Note  
• If you need the English menus instead of the Spanish or French  
menus, press MENU. Use /to select [Idioma] or [Langue]  
then press OK  
Use /to select [English], then press OK  
Press MENU to exit the main menu.  
24  
Item  
Detail  
USB  
Press 1 to display file details below.  
[Name] [Album] [Date] [Size] and [Next]  
Press 1 again to remove file details.  
More Detail  
This unit can play picture (JPEG) and video (Motion JPEG)
les  
Use the USB storage device that contains those les.  
Press 4 or OK to start the slide show.  
While the slide show is on, the following 2 settings  
will be displayed.  
Start show  
1
2
Insert the USB storage device into the USB terminal on  
this unit.The main menu appears automatically.  
Press 2, then use /to select the transition  
mode choosing from;  
[None] [Dissolve] [Wipe right] [Wipe left] [Wipe  
up] [Wipe down] [Box in] and [Box out]  
Use /to select [USB] and press OK  
The highlighted text will move to the name of your USB  
storage device, then press OK again.  
Transitions  
Press 3, then use /to change the display time  
choosing from; [Short] [Medium] and [Long]  
Slide time  
USB  
Picture  
Your USB  
Press 4 or OK to stop the slide show.  
While the slide show is off, the following 2 settings  
will be displayed.  
Sound  
This menu allows you to enjoy  
Stop show  
your pictures and videos  
via your USB device.  
Setup  
Every press on 2 will turn the picture clockwise by  
90 degrees.  
Features  
Language  
USB  
Rotate  
Press 3, then use /to select the zoom factor  
(1x, 2x or 4x). Press OK to set the zoom factor.  
Zoom  
3
Use /to select [Picture] or [Video] and then press  
OK  
Video (Motion JPEG)  
1
Use /to select the desired le, and then press OK  
Picture (JPEG)  
Your USB  
Video  
Video  
MOVIE1.avi  
Title:  
Use /to select the desired le, and then press OK  
1
MOVIE1.avi  
MOVIE1.avi  
MOVIE2.avi  
MOVIE3.avi  
MOVIE4.avi  
MOVIE5.avi  
Director:  
Date:  
Your USB  
Picture  
Picture  
2009/04/02  
00:06:37  
Image1.jpg  
Duration:  
Image1.jpg  
Image2.jpg  
Image3.jpg  
Image4.jpg  
Image5.jpg  
1
2
3
4
Image1.jpg  
1200:900  
Supported format: motion jpeg, 320  
x
240, 30FPS  
2009:04:02 17:42:06  
To stop playback and return to the file list, press  
BACK OK or CH▲  
1
2
3
4
Thumbnails  
Press “OK” key to play/pause.  
• Press CHto play back from the beginning.  
To toggle between [List] and [Thumbnails] press  
the Number 2 button each time.  
Item  
Detail  
• The unit goes to the slide show automatically.  
To pause/play the slide show, press OK  
• Use the Number buttons (1 through 4) to see the file  
Press 1 to display file details below.  
[Title] [Director] [Date] and [Duration]  
Press 1 again to remove file details.  
More Detail  
detail ( ) or change the following settings (  
See the description on the top of the next column  
~
).  
➁ ➃  
25  
English  
Note  
CONNECTING DEVICES  
• The unit recognizes only a USB storage device.  
• Do not use a USB hub or an extension cable to connect an  
external hard disk drive to the unit. (Not supported.)  
• A USB storage device is always inserted to this unit directly.  
• A USB storage device is not supplied with this unit.  
• We do not guarantee that all USB storage devices can be  
supported by this unit.  
No supplied cables are used with these connections:  
• Please purchase the necessary cables at your local store.  
• Be sure to keep a backup copy of the original les on your device  
before you play them back on this unit.We have no responsibilities  
for damage or loss of your stored data.  
To protect your USB storage device les from being erased place  
the write protect sliding tab in the protect position.  
• When you are ready to remove a USB storage device, at rst turn  
the unit off so it will go into standby mode to avoid any damage  
to your data and the unit.  
Before you connect:  
Be sure other device is connected properly before plugging in  
the AC power cord.  
External Device Connection  
• A USB storage device that requires its own driver or the device  
with a special system such as ngerprint recognition are not  
supported.  
• This unit is not allowed to use the USB storage device which  
requires an external power supply (500mA or more).  
• Up to 2GB (FAT16) or 8GB (FAT32) capacity can be supported.  
• Up to 10,000 les or 1,000 folders with 19 hierarchies can be  
recognized.  
HDMI Connection  
HDMI connection offers the highest picture quality.  
HDMI (High-Denition Multimedia Interface) transports high denition  
digital video and multi-channel digital audio through a single cable.  
Up to 255 English characters can be recognized.  
• This unit does not support MTP(MediaTransfer Protocol).  
• This unit supports FAT16 and FAT32 le systems.  
• If the le is not supported, an error message appears.  
• When the USB storage device is not recognized, try reconnecting  
it again.  
• Motion JPEG le with an extension of “.avi” can only be  
recognized.An extension of “.mov” is not supported.  
• This unit doesn’t support “pause”,forward” or “reverse” during  
video (Motion JPEG) playback.  
HDMI cable  
*
HDMI OUT  
The files recorded under the following specifications are required.  
<Picture (JPEG)>  
• Upper limit :  
24 Megapixel  
<Video (Motion JPEG)>  
TITLE  
5
CHAPTER 15  
REPEAT A-B  
Video  
Audio  
• Size : 320 x 240 (QVGA)  
• Frame rate : 30 fps  
• LPCM - Sampling frequency  
Blu-ray/DVD recorder  
with the HDMI output jack  
(32 kHz, 44.1 kHz or 48 kHz)  
- Quantization bit rate (16 bit)  
For LC320EM2, you can also use the HDMI jack on the Rear Panel.  
*
HDMI-DVI Connection  
This unit can be connected to your device that has a DVI  
terminal. Use an HDMI-DVI conversion cable for this connection  
and it requires audio cable for Analog Audio signal as well.  
cable receiver or satellite box with  
the DVI output jack  
STEREO  
PCM  
To HDMI 1 Input  
jack only for 32”  
AUDIO OUT  
DVI OUT  
L
R
HDMI-DVI  
conversion cable  
HDMI-DVI  
conversion cable  
For 22” and 19”  
audio cables  
26  
CompositeVideo Connection  
Note  
CompositeVideo connection offers standard picture quality  
for video devices connected to the unit. If you connect to the  
unit’s CompositeVideo Input jack, connect audio cables to the  
Audio L/R Input jacks below the CompositeVideo connector  
jack.When the Audio is monaural, then only connect to the  
Audio L Input jack.  
• Use an HDMI cable with the HDMI logo (a certied HDMI cable).  
High Speed HDMI cable is recommended for the better  
compatibility.  
For HDMI connection (use HDMI Input jack)  
• The unit accepts 480i, 480p, 720p, 1080i and 1080p 24/30/60Hz  
of video signals, and 32kHz, 44.1kHz and 48kHz of audio signals.  
• This unit accepts 5.1 channel audio signal (Dolby Digital) and 2  
channel audio signal (LPCM).  
• This unit accepts only signals in compliance with EIA861.  
For HDMI-DVI connection  
• The unit accepts 480i, 480p, 720p, 1080i and 1080p video signals.  
• HDMI-DVI connection requires separate audio connections as  
well and the audio signals are converted from digital to analog.  
• DVI does not display 480i image which is not in compliance with  
EIA/CEA-861/861B.  
camcorder  
video game  
STAND-BY  
STEREO  
ComponentVideo Connection  
ComponentVideo connection offers better picture quality for  
video devices connected to the unit.  
VCR  
If you connect to the unit’s ComponentVideo Input jacks,  
connect Analog Audio cables to the Analog Audio L/R Input  
jacks right below the ComponentVideo connector jacks.  
VIDEO  
OUT  
AUDIO OUT  
L
R
video cable  
component video cables  
(red/blue/green)  
audio cables  
Note  
audio cables  
• Whenever you connect to the CompositeVideo Input jack,  
you must disconnect the ComponentVideo Input jacks (Pb and Pr).  
If you leave those jacks connected, it may cause of unstable picture.  
(green) (blue) (red)  
Digital Audio Output Connection  
(for digital broadcasting only)  
AUDIO OUT  
COMPONENT VIDEO OUT  
Pb/Cb Pr/Cr  
L
R
Y
If you connect this unit to an external digital audio device, you  
can enjoy multi-channel audio like 5.1ch digital broadcasting  
sound.  
TITLE  
5
CHAPTER 15  
REPEAT A-B  
Use a digital audio coaxial cable to connect the unit to  
external digital audio devices.  
Blu-ray/DVD recorder  
with the component video output jacks  
Note  
• The unit accepts 480i/480p/720p and 1080i of video signals for  
this connection.  
DIGITAL AUDIO  
COAXIAL IN  
Dolby Digital  
decoder  
digital audio coaxial cable  
27  
English  
PC Connection  
USB Storage Device  
This unit offers easy playback of picture (JPEG) and video  
(Motion JPEG) les.  
unit to your PC, you can use this unit as a PC monitor.  
Use aVGA cable for thisVideo connection and it requires a  
stereo mini plug conversion cable for Analog Audio signal as  
well.  
Insert the USB storage device into the USB terminal shown  
below. [USB]  
p.24  
32”  
personal computer  
mini audio cable  
audio cables  
22”/19”  
VGA cable should be  
with ferrite core.  
VGA cable  
The following video signals can be displayed:  
Format  
VGA  
Resolution  
640  
Refresh rate  
480  
600  
768  
768  
768  
SVGA  
XGA  
800  
1,024  
1,280  
1,360  
60Hz  
WXGA  
Other formats or non-standard signals will not be displayed  
correctly.  
Note  
• Please purchase the VGA cable that has a ferrite core.  
• The following operations may reduce noise.  
- Attach a ferrite core to the AC power cord of your PC.  
- Unplug the AC power cord and use the built-in battery of your  
PC.  
28  
USEFULTIPS  
FAQ  
Question  
Answer  
Check the antenna or cable connection to the main unit.  
Check the batteries of the remote control.  
Check if there is an obstacle between the infrared sensor window and the remote control.  
Test the signal output use [IR Signal Check]  
If okay, then possible infrared sensor trouble.  
p.30  
My remote control does not work.  
What should I do?  
Aim the remote control directly at the infrared sensor window on the front of the unit.  
Reduce the distance to the unit.  
Re-insert the batteries with their polarities (+/– signs) as indicated.  
When there is an infrared-equipped device such as PC near this unit, it may interrupt the remote  
control signal of this unit.  
Move the infrared-equipped device away from this unit, change the angle of the infrared sensor or  
turn off the infrared communication function.  
How come the Initial setup  
appears every time I turn on this  
unit?  
Connect the RF coaxial cable to the unit directly and run the initial setup.  
Make sure to complete the channel scan before the unit goes into standby mode.  
Make sure [Autoprogram] has been completed.  
Autoprogram must be completed when you set up the unit for the rst time or move it to a location  
where previously unavailable channels are broadcast.  
p.17  
The selected channel may not be broadcasting.  
Why can I not watch some RF  
signalTV programs.  
When [Autoprogram] is interrupted and not completed, some channels will not be received. Make  
sure to complete the Autoprogram.  
The selected channel cannot be viewed by the [Child Lock] setting.  
p.17  
p.20  
The unit requires some kind of antenna input.An indoor antenna (VHF/UHF), an external antenna  
(VHF/UHF) or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the unit  
Check if the correct input mode is selected by pressing SOURCE or using CH/[Switching Each  
Input Mode]  
p.12  
How come there is no image from  
the connected external devices?  
Check the antenna or cable connection to the unit.  
When using the ComponentVideo Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/  
Cr) connectors are connected to their corresponding colored jacks on the unit.  
Many digital channels have alternate channel numbers.The unit changes the numbers automatically to  
the ones signifying the broadcasting station channel number.These basic numbers used for previous  
analog broadcasts. (e.g., input ch#30 auto changes to ch#6.1)  
When I enter a channel number, it  
changes automatically.  
Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts.  
Most captioning production companies can display a dialog to maximum of 220 words per minute. If  
a dialog exceeds that rate, selective editing is used to insure that the captions remain up-to date with  
the currentTV screen dialog.  
Why are captions not displayed  
entirely? Or, captions are delayed  
behind the dialog.  
How can I set the clock ?  
There is no clock function on this unit.  
I cannot change the [Child Lock]  
setting because my PIN code no  
longer works.  
If a Power failure occurs for longer than 10 seconds the child lock setting is retained, but the PIN code  
is set to the default code “0000”. [Child Lock]  
p.20  
Troubleshooting Guide  
If the unit does not perform properly when operated as instructed in this manual,  
check the following chart and all connections once before calling for service.  
Symptom  
Remedy  
Make sure the AC power cord is plugged in.  
Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the  
AC outlet to ensure that AC outlet operates normally.  
No power  
If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to reset itself.  
Press only one button at a time. Do NOT press more than one button at the same time.  
Ensure that no buttons on the remote control are depressed and move freely.  
Control button's do not work.  
Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.  
Check whether all the cables to the unit are connected to the correct output jack of your device like  
Blu-ray/DVD recorder.  
Power is ON but no screen image.  
Make sure that the selected input mode is connected to the working input jack.  
Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode.Tap  
any key on the keyboard to wake up your computer.  
29  
English  
Symptom  
Remedy  
Check if the power is on.  
Check if the correct input mode is selected.  
Check whether all the cables to the unit are connected to the correct output jack of your device like  
Blu-ray/DVD recorder.  
View otherTV channels.The problem might be limited to the broadcasting station or weak signal  
strength.  
Unplug the AC power cord and wait for about 1 minute, then plug the AC power cord and turn on  
the unit again.  
No picture or sound  
Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.  
Make sure that the selected input mode is connected to the working input jack.  
Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode.Tap  
any key on the keyboard to wake up your computer.  
Make sure that the sound is not muted. Press MUTE  
so that the volume bar and current volume  
level will appear on theTV screen.  
Make sure that the volume is NOT set to [ ] or [Mute]. If so, use VOL  
/
to adjust the desired  
0
volume.  
View otherTV channels.The problem might be limited to the broadcasting station or weak signal  
strength.  
Adjust [Color] in the main menu.  
No color  
Adjusted [Picture] or [Sound]  
settings are not effective every time  
the unit is turned on.  
You must set [Home] in [Location]  
p.23  
Otherwise, the settings you adjusted will not be memorized after the unit goes into standby mode.  
Electrical interference from nearby appliances may affect picture quality.  
Adjust [Contrast] and [Brightness] in the main menu.  
View otherTV channels.The problem might be limited to the broadcasting station or weak signal  
strength.  
For the best picture quality, watch "High Definition" wide screen programs.  
If the HD content is not available, watch "Standard Definition" programs instead.  
Sound OK, picture poor  
Picture OK, sound poor  
View otherTV channels.The problem might be limited to the broadcasting station or weak signal  
strength.  
Check if the audio cable is connected in correctly.  
You may be getting interference from electrical appliances, automobiles, motorcycles or uorescent  
lights.  
Try moving the unit to another location to see if this is the cause of the problem.  
You see a distorted picture or hear  
an unusual sound.  
Electrical interference from nearby appliances may affect picture quality.  
View otherTV channels.The problem might be limited to the broadcasting station or weak signal  
strength.  
Ghosts, lines or streaks in picture  
You see "noise" or "trash" on the  
When the capabilities of the unit exceed the capabilities of the digital broadcasting, the signal will be  
increased to match the capabilities of the display of the unit.This may cause noise or trash.  
screen.  
Different color marks on theTV  
screen  
View otherTV channels.The problem might be limited to the broadcasting station, missing data or  
pixelation.  
This unit will memorize the volume level from the last time you adjusted it.  
If the volume of the sound from another device is higher or lower, then the loudness will change.  
You switch to a different input and  
the volume changes.  
You switch to a different input and  
the screen size changes.  
This unit will memorize the viewing mode from the last time you used the particular input modes.  
If you are using the unit as a PC monitor, make sure that [Horizontal Position] and [Vertical Position]  
in [PC Settings] are set correctly.  
The display image does not cover  
the entire screen.  
If you are watchingTV or using the CompositeVideo, ComponentVideo or HDMI with 480i Input,  
press FORMAT  
repeatedly to switch various screen modes.  
Captions are displayed as a white  
box. No caption is displayed in  
the Closed Caption-supported  
program.  
Interference from buildings or weather conditions may cause captioning to be incomplete.  
Broadcasting station may shorten the program to insert advertisement.  
The closed caption decoder cannot read the information of the shortened program.  
Black box is displayed on theTV  
screen.  
The text mode is selected for caption. Select [CC-1] [CC-2] [CC-3] [CC-4] or [Off]  
Note  
• The LCD screen is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a xed point of blue,  
green or red.  
This is not to be considered a defect in the LCD screen.  
• Some functions are not available in specic modes, but this is not a malfunction. Read the description in this manual for more details on  
correct operations.  
30  
INFORMAT
ION  
Glossary  
Maintenance  
ATSC  
Cabinet Cleaning  
Wipe the front panel and other exterior surfaces of the  
unit with a soft cloth.  
Never use a solvent or alcohol. Do not spray insecticide  
liquid near the unit. Such chemicals may cause damage and  
discoloration to the exposed surfaces.  
Acronym that stands for AdvancedTelevision Systems Committee and  
the name of the digital broadcasting standards.  
Aspect Ratio  
The width of aTV screen relative to its height. ConventionalTVs  
are 4:3 (in other words, theTV screen is almost square); widescreen  
models are 16:9 (theTV screen is almost twice as wide as its height).  
CEC (Consumer Electronics Control)  
This allows you to operate the linked functions between our brand  
devices with CEC feature and this unit.We do not guarantee 100%  
interoperability with other brands of CEC compliant devices.  
Panel Cleaning  
Wipe the panel of the unit with a soft cloth. Before cleaning  
the panel, disconnect the AC power cord.  
ComponentVideo  
This is a video signal format that conveys each of 3 principal colors  
of light (red, blue and green) through different signal lines.This allows  
the viewers to experience picture colors as original as it is.There are  
several signal formats, includingY/Pb/Pr andY/Cb/Cr.  
Servicing  
Dolby Digital  
The system developed by Dolby Laboratories to compress digital  
sound. It offers stereo sound (2ch) or multi-channel audio.  
Should your unit become inoperative, do not try to correct  
the problem yourself.There are no user serviceable parts  
inside. Call our toll free customer support line found on the  
cover of this manual to locate an authorized service center.  
E-Sticker  
E-Sticker is showing set features, technical information, etc on thisTV  
set that is displayed on theTV screen. Previously the information was  
on a printed sticker that was put on the display.  
IR Signal Check  
If the remote control is not working properly, you can use a  
digital camera (including a cellular phone with built-in camera)  
to see if it is sending out an infrared signal.  
HDMI (High-Definition Multimedia Interface)  
Interface that supports all uncompressed, digital audio/video formats  
including set-top box, Blu-ray/DVD recorder or digital television, over  
a single cable.  
HDTV (High DefinitionTV)  
Ultimate digital format that produces high resolution and high picture  
quality.  
With a digital camera  
(including built-in cell phone cameras):  
Point the Digital Camera towards the remote  
control infrared diode at the front of the  
remote control. Press any button on the  
remote control and look through the camera  
display. If the infrared pulsating light appears  
through the camera, the remote control is  
sending out an IR signal.  
NTSC  
Acronym that stands for NationalTelevision Systems Committee and  
the name of analog broadcasting standards.  
Off the air NTSC signals are no longer being sent by major  
broadcasting stations in the USA.  
PIN code  
A stored 4-digit number that allows access to parental control features.  
SAP (Secondary Audio Program)  
Second-audio channel delivered separately from main-audio channel.  
This audio channel is used as an alternate in bilingual broadcasting.  
SDTV (Standard DefinitionTV)  
Standard digital format that is similar to the NTSC picture quality.  
31  
English  
Other Specications  
TV format  
Closed Caption system  
ATSC/NTSC-MTV standard  
Terminals  
Antenna Input VHF/UHF/CATV  
75Ω unbalanced (F-type)  
500mV rms  
Audio Input  
RCA jack (L/R) x 2  
§15.122/FCC (digital CC)  
§15.119/FCC (analog CC)  
Component/CompositeVideo Input jacks forVIDEO  
RCA jack x 3  
Y/VIDEO 1V p-p(75Ω)  
Pb/Cb 700mV p-p(75Ω)  
Pr/Cr 700mV p-p(75Ω)  
Channel coverage (ATSC/NTSC)  
Terrestrial DTV (ATSC)  
VHF 2~13  
UHF 14~51 (each channel has e.g.  
<LC320EM2>  
HDMI Input  
<LC220EM2/LC190EM2>  
HDMI Input  
USB Input  
PC Input  
2.1~2.9, 3.1~3.9, etc.)  
HDMI 19pin x 2  
Terrestrial Analog (NTSC)  
VHF 2~13  
HDMI 19pin x 1  
USB x 1  
D-Sub 15pin x 1(RGB)  
UHF 14~69  
2~13,A~W,  
CATV  
W+1~W+94 (analog W+1~W+84),  
Digital Audio Output (coaxial)  
A-5~A-1, 5A  
RCA jack x 1  
500mV p-p (75Ω)  
Tuning system  
Channel access  
Channel frequency synthesized tuning  
system  
Direct access keyboard,  
Programmable scan, and up/down  
<LC220EM2/LC190EM2 only>  
Headphone Audio Output  
1/8 inches x 1(3.5mm)  
Remote control  
Digital encoded infrared light system  
Operating temperature  
Electrical Specication  
41°F (5°C) to 104°F (40°C)  
<LC320EM2>  
Power requirements  
Audio Output  
5W, 8Ω x 2  
120V~ AC +/10%, 60Hz +/0.5%  
<LC220EM2/LC190EM2>  
[LC320EM2]  
Audio Output  
1.5W, 8Ω x 2  
Power consumption (maximum)  
110W  
32inches (31.5 inches measured diagonally)  
<without base> <with base>  
Width 30.0 inches (760.0mm) 30.0 inches (760.0mm)  
LCD  
Dimensions  
Height 19.6 inches (497.0mm) 21.4 inches (543.0mm)  
Depth 3.8 inches (95.0mm)  
9.5 inches (240.4mm)  
16.10 lbs. (7.30kg)  
17.42 lbs. (7.90kg)  
Weight  
[LC220EM2]  
Power consumption (maximum)  
57W  
22inches  
<without base>  
Width 21.3 inches (539.0mm) 21.3 inches (539.0mm)  
(21.6 inches measured diagonally)  
<with base>  
LCD  
Dimensions  
Height 14.4 inches (364.5mm) 16.0 inches (406.0mm)  
Depth 3.6 inches (89.0mm)  
8.93 lbs. (4.05kg)  
8.3 inches (208.3mm)  
9.48 lbs. (4.30kg)  
Weight  
[LC190EM2]  
Power consumption (maximum)  
40W  
19inches  
<without base>  
Width 18.9 inches (478.0mm) 18.9 inches (478.0mm)  
(18.5 inches measured diagonally)  
<with base>  
LCD  
Dimensions  
Height 12.8 inches (324.5mm) 14.5 inches (367.8mm)  
Depth 3.3 inches (82.0mm)  
7.26 lbs. (3.29kg)  
8.3 inches (208.3mm)  
7.81 lbs. (3.54kg)  
Weight  
Designs and specications are subject to change without  
notice and without our legal obligation.  
If there is a discrepancy between languages, the default  
language will be English.  
32  
33  
English  
LIMITED WARRANTY  
( )  
(
)
NINETY 90 DAY LABOR / ONE 1 YEAR PARTS  
WARRANTY COVERAGE:  
This warranty obligation is limited to the terms as set forth  
below.  
mission, or (d) if any serial number has been removed or defaced,  
or (e) product, accessories or consumables sold “AS IS” without  
warranty of any kind by including refurbished product sold “AS  
IS” by some retailers.  
WHO IS COVERED:  
This product warranty is issued to the original purchaser or the  
person receiving the product as a gift against defects in materials  
and workmanship as based on the date of original purchase  
(“Warranty Period”) from an Authorized Dealer. The original  
sales receipt showing the product name and the purchase date  
from an authorized retailer is considered such proof.  
This Limited Warranty does not cover:  
Shipping charges to return defective product.  
Labor charges for installation or setup of the product, adjust-  
ment of customer controls on the product, and installation or  
repair of antenna/signal source systems outside of the product.  
Product repair and/or part replacement because of improper  
installation or maintenance, connections to improper voltage  
supply, power line surge, lightning damage, retained images or  
WHAT IS COVERED:  
This warranty covers new products if a defect in material or  
workmanship occurs and a valid claim is received within the  
Warranty Period. At its option, the company will either (1)  
repair the product at no charge, using new or refurbished  
replacement parts, or (2) exchange the product with a product  
that is new or which has been manufactured from new, or ser-  
viceable used parts and is at least functionally equivalent or most  
comparable to the original product in current inventory, or (3)  
refund the original purchase price of the product.  
tent for extended periods, product cosmetic appearance items  
due to normal wear and tear, unauthorized repair or other  
cause not within the control of the company.  
Damage or claims for products not being available for use, or  
for lost data or lost software.  
Damage from mishandled shipments or transit accidents when  
returning product.  
Replacement products or parts provided under this warranty are  
covered against defects in materials and workmanship from the  
date of the replacement or repair for ninety (90) days or for the  
remaining portion of the original product’s warranty, whichever  
provides longer coverage for you. When a product or part is  
exchanged, any replacement item becomes your property and the  
replaced item becomes company property. When a refund is  
given, your product becomes company property.  
it to operate in any country other than the country for which  
it was designed, manufactured, approved and/or authorized, or  
A product used for commercial or institutional purposes  
(including but not limited to rental purposes).  
can be provided.  
Failure to operate per Owner’s Manual.  
Note: Any product sold and identified as refurbished or  
renewed carries a ninety (90) day limited warranty.  
TO OBTAIN ASSISTANCE…  
Contact the Customer Care Center at:  
1-866-309-8819  
Replacement product can only be sent if all warranty  
requirements are met. Failure to follow all requirements  
can result in delay.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS  
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-  
SUMER, WITH THE ISSUING COMPANY NOT LIABLE FOR  
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR  
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY  
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE  
ON THIS PRODUCT IS LIMITED IN DURATION TO THE  
DURATION OF THIS WARRANTY.  
WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-  
TATIONS:  
This Limited Warranty applies only to new company manufac-  
to any hardware product or any software, even if packaged or  
sold with the product, as manufacturers, suppliers, or publishers  
may provide a separate warranty for their own products pack-  
aged with the bundled product.  
The company is not liable for any damage to or loss of any pro-  
grams, data, or other information stored on any media contained  
within the product, or other additional product or part not cov-  
ered by this warranty. Recovery or reinstallation of programs,  
data or other information is not covered under this Limited  
Warranty.  
Some states do not allow the exclusions or limitation of inciden-  
tal or consequential damages, or allow limitations on how long an  
implied warranty lasts, so the above limitations or exclusions may  
not apply to you.  
This warranty does not apply (a) to damage caused by accident,  
abuse, misuse, neglect, misapplication, or non-supplied product,  
(b) to damage caused by service performed by anyone other than  
company approved Authorized Service Location, (c) to a product  
FUNAI CORPORATION, Inc. 19900 Van Ness Avenue, Torrance, CA 90501  
Printed inThailand  

Toshiba Air Conditioner Rav Sm1404bt Tr User Manual
Schumacher Automatic Sp1 User Manual
Samsung Avmkc035ea User Manual
Precisionaire Pb1900 0604 User Manual
Philips Telephone Answering Machine User Manual
Nec Rwc 4717 User Manual
LG 32TNF5J User Manual
CRAFTSMAN 113.242502 User Manual
BROTHER HL 5450DN User Manual
ACER ASPIRE 5050 User Manual