Delvcam
DELV-HDMIB
User Guide
YP-01150117
Features
Ø
Ø
Ø
Ø
Ø
Ø
High resolution: 1280×800;
High brightness: 400cd/㎡;
High contrast: 800:1;
Built-in battery & battery level;
HDMI & AV input;
Foldable sun shade;
Safety Instructions
Ø
Ø
Ø
Please do not place the display screen face down.
Please do not drop onto the ground and avoid heavy impact.
Please do NOT use chemical solutions to clean this product. Please wipe
with a clean soft cloth to maintain the brightness of the surface.
Ø
Ø
Please do not block any ventilation or antenna ports.
Please follow the instructions and trouble-shootings to adjust the product.
Other improper adjustment may result in damage. Any further adjustment
must be performed or conducted by a qualified technician.
Ø
Please unplug the power and remove the battery for long-term storage, or
during lightning storms.
2
Installation & Initial Setup
v Unpacking
Carefully unpack the monitor and verify that the following items are included:
l
l
l
l
l
l
l
l
l
Monitor
Sun shade
AV input cable
AV output cable
12V DC adapter
HDMI A/C cable
Shoe mount
2600mAh built-in battery
Manual
Inspect the unit for any physical damage that may have occurred during shipping.
Should there be any damage, please immediately contact us.
v Optional Accessories
Accessory options. (Sold Separately)
l
l
l
l
l
l
VESA battery plate + Battery plate
VESA folding bracket
Mount plate bracket
Anton Bauer / V-mount mount
VESA rail slot
Li-ion battery
Tip: Use original accessories to prevent device from damage.
3
Product Description
1. F1、F2 User-definable buttons.
2. A/V: switch to AV state.
3. HDMI: switch to HDMI state.
4. Battery indicator
Status 1: the indicator light turns to fully red when battery charging.
Status 2: the indicator light turns to half red when powered with DC
power, but not with battery.
Status 3: the indicator light turns to off when charge completely or
use only with battery.
5. M/E: to activate OSD (on-screen display) menu.
Select switch the brightness, contrast, saturation, Tint, sharpness,
volume, MENU and Exit.
6. < Left selection key, to select items on OSD menu and value
option adjustment:
Press to adjust the brightness, contrast, saturation, Tint, sharpness
and volume value decrease.
7. > Right selection key, to select items on OSD menu, value
option adjustment and confirmation:
Press to adjust the brightness, contrast, saturation, Tint, sharpness
and volume value increase.
8. ENTER.
4
1. OUT: video output interface.
2. IN: video input interface.
3. Bracket mount (Depth limit 0.5cm).
4. Earphone jack.
5. HDMI input interface.
6. POWER: DC12V power input.
1. VESA mounting interface.
2. Speaker.
3. 2600mA battery slot (built-in).
5
Sunshade Installation
DV Battery Mount Plate (Optional)
Following three types of battery plates are suitable for this device, model
F970, QM91D, DU21 & LP-E6 (choose 2 out of 4).
6
MODEL: F-970
MODEL: QM91D
MODEL: DU21
MODEL: LP-E6
DV Battery Mount Plate:
DV Battery Mount Plate Specification:
Model DU21 for battery of Panasonic DV:
NV-GS/PV-GS/DZ-MV/GS/H28/H258/H288GK series, comply with
Panasonic battery DU06/VBD140/SANYO DZhs301sw/Hitachi
DZ-HS303SW/BZ-BP14S/DZ3200/BP07W.
Model QM91D for battery of SONY DV:
DSCR1/F/S/MVCCD/E/HC15E/HC1E/AE1u/DCRTRV828/E/CCD-TRV
116/DCR-DVD/PS105K/300K/10P/1E series.
Model F970 for battery of SONY DV:
DCR-TRV series, DCR-TRV E series, VX2100E PD P series, GV-A700,
GV-D800 FD/CCD-SC/TR3/FX1E/HVR-AIC, HDR-FX1000E, HVR-Z1C,
HVR-V1C, FX7E F330.
Model LP-E6 for battery of Canon DSLR:
5D Mark II/5D Mark III/EOS7D/EOS60D;
Wiring Instructions
v Video Output Cable
1. Video output interface.
2. Yellow: video 1 output plug.
3. White: video 2 output plug.
7
v Video Input Cable
1. Video input interface.
2. Yellow: video 1 input plug.
3. White: video 2 input plug.
Menu Settings
Before setting the functions, please make sure the device is connected correctly.
Shortcut keys
The image menu
When power on, press “< / >” key on the device, brightness will appear at
the bottom of the screen, then press the MENU button to select brightness,
sharpness, contrast, saturation, volume, tint, MENU and Exit. User can adjust
the parameters of the selected item with “< / >”button to meet their needs.
F1-F2 user-definable function buttons
Long press any F1-F2 key for 3-5 seconds to pop-up
shortcut menu directly. As shown in Figure (default
menu button in white font).
Use “< / >” buttons to select the desired option.
Finally, use the “ENTER” key to confirm the selected
item as default.
Functions of F1-F3 buttons can also be customized:
Center Marker, Safety Marker, Check Field, Color Bar,
Aspect Ratio, Camera, Image Flip, Zoom, Pixel-to-Pixel,
Freeze Input, Underscan, H/V delay.
Icon Display
Icons will display on screen when signal connected.
Select “Marker” on menu, and turn off “FPV Marker. And the icons
will be invisible on screen.”
8
l
l
l
l
l
Battery: battery level indicator.
Voltage: voltage indicator (invisible when charging)
Timer: available for flying countdown or battery level countdown.
Channel frequency: searching channel automatically.
Signal: wireless signal sensitivity indicator.
Menu Operation
When power on, press “MENU” on the device. The menu of function
setting will display on the screen.
Press < / > buttons to choose menu; then press ENTER to confirm; after
that, press MENU to return.
PICTURE
ITEMS
Brightness
Contrast
Saturation
Tint
OPTIONS
0 – 100
0 – 100
0 – 100
0 – 100
0 – 100
Sharpness
Color Temp
6500K, 7300K, 9300K, User
Color Temp R
Color Temp G
Color Temp B
Note: Available only under
“User” mode to choose the
color value you need.
9
MARKER
ITEMS
OPTIONS
Center Marker
Safety Marker
ON, OFF
OFF, 95%, 93%, 90%, 88%, 85%, 80%
DISPLAY
ITEMS
OPTIONS
Aspect Ratio
Pixel-to-Pixel
Underscan
Zoom
Image Flip
Freeze Input
Full Screen, 4: 3, 16: 9, 1.85: 1, 2.35: 1
ON, OFF
ON, OFF
OFF, ×2, ×4, ×6, ×8
OFF, H, V, H / V
ON, OFF
10
DSLR AUX & AUDIO
ITEMS
Camera
OPTIONS
ON, OFF ( Only HDMI mode)
H / V Delay
Check Field
Color Bar
Volume
OFF, H&V, V, H
OFF, Mono, Red, Green, Blue
ON, OFF
0 – 100
SYSTEM
ITEMS
Language
LOGO
OPTIONS
English, Chinese
ON, OFF
Back Light
Manufacture Default
ISP
0 – 100
ON, OFF
11
Technical Specifications
Panel
7” LED Backlit ( IPS )
Physical Resolution
Brightness
Contrast
1280×800
400cd/㎡
800:1
178°/178°（H/V）
DC 7~24V
16:9
Viewing Angle
Input Voltage
Aspect Ratio
Current
580mA
Power Consumption
≤7W
Operating Temperature -20°~ 60°C
Storage Temperature
Dimension (LWD)
Weight
-30°~ 70°C
185×126×30 (mm)
360g
Trouble Shooting
1. Only black-and-white display
Check whether the brightness or color saturation is properly setup or not.
2. No image
Check the power input and connection
3. When on the picture shows size error
Press “ MENU → DISPLAY → Underscan ” to zoom in/out pictures
automatically when receiving HDMI signals
4. Other problems
Please choose “MENU→SYSTEM→ Manufacturer Default →ON”
Note: due to constant effort to improve products and product
features, specifications may change without notice.
12
|