D LINK AC1200 DWR 961 User Manual1

Wireless AC1200 4G lTe rouTer  
DWr-961  
QUICK  
INSTALLATION  
GUIDE  
PrODuCT  
SETuP  
BAsiC seTuP  
Ensure that your DWR-961 Wireless AC1200 4G LTE Router is powered off before performing the  
steps below.  
1. Verify that your SIM/UICC card is installed and has been activated by your carrier.  
2. Attach the included antennas to the back of the router, screwing them in clockwise.  
Arrange them so that they point upward.  
SIM/UICC card  
3. Connect the power adapter to the socket on the back panel of your DWR-961. Plug the other  
end of the power adapter into a wall outlet or power strip. Make sure the power button is in the  
"On" position  
a. The Power LED will light up to indicate that power is being supplied to the router and the  
router is turned on.  
b. The network LED on the front panel will flash on and off as the DWR-961 performs  
initialization and Internet connection processes.  
c. After a few moments, if a connection has been established, the following LEDs will turn solid  
green: Power, Internet, 2.4 GHz or 5 GHz (if enabled), 4G (if connected), LAN (if connected),  
WAN (if connected), and Signal Strength.  
Note: By default, the DWR-961 uses the mobile network as the sole Internet connection. If you  
wish to use your mobile connection as a backup to a wired connection, or you wish to use a  
wired connection exclusively, you must use the Optional Advanced Setup procedure.  
4. Connect via Wi-Fi using the SSID and password printed on the bottom of the router, or through  
Ethernet via one of the LAN ports on the back of your DWR-961.  
oPTioNAl ADVANCeD seTuP (ACCess ViA iP ADDress)  
1. Once connected to your router, open a web browser and enter the IP address below into the  
browser address field. Log in using the username and password below.  
USERNAME: admin  
PASSWORD: [leave this blank]  
2. After logging in, you can access the setup wizard which will guide you through the rest of the  
setup process. To reach the wizard, click the Internet tab on the bar along the top, then click  
Wizard on the left hand side. Follow the on-screen instructions.  
For additional information, see the user manual.  
3
DWr-961  
TrOuBlESHOOTiNG  
seTuP AND CoNFiGurATioN ProBleMs  
1. HOW DO i CONFiGurE MY DWr-961 rOuTEr Or CHECK MY WirElESS NETWOrK  
NAME (SSiD) AND WirElESS ENCrYPTiON KEY?  
- Connect your PC to the router using an Ethernet cable.  
- Open a web browser and enter the router's IP address: http://192.168.0.1 into the address bar.  
- Log into the router using the default username admin. By default, the password is left blank.  
- Once logged in, you can use the wizard to configure the router, or make changes manually.  
Note: If you have changed the password and cannot remember it, you will need to reset the  
router to factory defaults. The default SSID and password are printed on the bottom of your  
router.  
2. HOW DO i rESET MY DWr-961 rOuTEr TO FACTOrY DEFAulT SETTiNGS?  
- If you cannot remember your router administrator password, you may use an implement such as  
a straightened paperclip to press and hold the reset button on the left-hand side of the router for  
about 10 seconds.  
Note: Resetting the router to factory default settings will erase the current configuration. To  
reconfigure your router, log in as outlined in question 1, then run the Setup Wizard.  
3. HOW DO i ADD A NEW WirElESS CliENT Or PC iF i HAVE FOrGOTTEN MY  
WirElESS NETWOrK NAME (SSiD) Or WirElESS ENCrYPTiON KEY?  
- For every PC that needs to connect to the router wirelessly, you will need to ensure you use the  
correct Wireless Network Name (SSID) and encryption key.  
- Use the web-based user interface (as described in question 1 above) to check or choose your  
wireless settings.  
- Make sure you write down the SSID and password so that you can enter them into each  
wirelessly connected PC. You will find a dedicated area on the back of this document to record  
this important information for future use.  
4. WHY AM i uNABlE TO ESTABliSH AN iNTErNET CONNECTiON?  
- If connecting using a 4G LTE mobile connection, make sure that you are within range of the  
mobile service provider, and that the service has been correctly configured.  
Important: Due to variances in 4G LTE signal saturation, it may be necessary to try setting  
up the D-Link High-Speed Internet Router in various rooms and locations to obtain the signal  
strength necessary for a strong mobile connection.  
- If connecting using the WAN via ADSL/Cable service, make sure the modem has been enabled,  
connected, and is operational, and that the service is correctly configured.  
Technical Support  
For Product Warrant or Technical Support  
Call USCC Tech Support  
1-800-944-9400  
Ver.1.00(USCC)_130x183 2017/10/12  
29072600D961C10  

Universal Power Group 24bc8000 L 1 User Manual
Uniden Dect3181 User Manual
Trane Air Conditioner Rtac 140 400 Ton Units 50 Hz User Manual
Samsung Mc19ac2 12 User Manual
Oki S700 User Manual
MAKITA XRU01 User Manual
HP COMPAQ LE2002X User Manual
D LINK DAP 1353 02 User Manual
CANON TS3400 User Manual
ACCO BRANDS SEAL 54 BASE User Manual