BROTHER HL 5450DNT 02 User Manual

Thank you for choosing Brother, your support is important to us and we value your business. Your Brother product is  
engineered and manufactured to the highest standards to deliver reliable performance, day‑in and day‑out.  
Please read the Product Safety Guide first, then read this Quick Setup Guide for the correct setup and installation  
procedure. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/.  
Note: Not all models are available in all countries.  
Quick Setup Guide  
ENG  
Version 0  
HL-5440D  
(EU Only)  
HL-5450DN(T)  
Unpack the machine and check the components  
Printer LED Indications  
Note  
WARNING  
Blinking:  
or  
or  
ON: or or  
OFF:  
1
• The components included in the box may differ depending on your country.  
• We recommend that you save the original packaging.  
• Plastic bags are used in the packing of your machine. Plastic bags are not toys. To  
avoid the danger of suffocation, keep these bags away from babies and children  
and dispose of them correctly.  
Sleep/  
Deep Sleep  
Warming Up/  
Cooling Down1  
Receiving Data/  
Data Remaining2  
OFF  
Ready  
• If for any reason you must ship your machine, carefully repack the machine in the original  
packaging to avoid any damage during transit. The machine should be adequately insured with  
the carrier. For how to repack the machine, see Packing and shipping the machine in the User’s  
Guide.  
Drum Unit and Toner  
Cartridge Assembly  
Quick Setup Guide  
Back Cover  
Toner  
• If you use a Lower Tray, DO NOT carry the machine with the Lower Tray as you may  
be injured or cause damage to the machine because it is not attached to the Lower  
Tray.  
(pre‑installed)  
Start Here  
• Illustrations in this Quick Setup Guide are based on the HL‑5450DN.  
Drum  
• The interface cable is not a standard accessory. Buy the appropriate interface cable for the  
connection you want to use (USB, parallel (HL‑5440D only) or Network (HL‑5450DN(T) only)).  
WARNING indicates a potentially  
hazardous situation which, if not avoided,  
could result in death or serious injuries.  
Paper  
Note  
WARNING  
USB cable  
Error  
Keep a minimum gap around the machine as shown in the illustration.  
It is recommended to use a USB 2.0 (Type A/B) interface cable that is no longer than 2 meters  
(6 feet).  
Product Safety Guide  
AC Power Cord  
Installer CD-ROM  
CAUTION indicates a potentially  
Ready  
150 mm (6 in.)  
Dimmed  
CAUTION  
hazardous situation which, if not avoided,  
may result in minor or moderate injuries.  
Parallel cable (HL-5440D only)  
DO NOT use a parallel interface cable that is longer than 2 meters (6 feet). Use a shielded  
interface cable that is IEEE 1284‑compliant.  
150 mm  
(6 in.)  
150 mm  
(6 in.)  
Drum End  
Soon3  
150 mm  
(6 in.)  
Toner Low3  
Replace Toner  
Drum Stop  
Drum Error2  
Network cable (HL-5450DN(T) only)  
Use a straight‑through Category 5 (or greater) twisted‑pair cable for 10BASE‑T or 100BASE‑TX  
Fast Ethernet Network.  
Back Cover  
Toner  
Drum  
Paper  
Error  
Remove the packing material from the machine  
Ready  
Important  
c. Press the front cover release button and open the front cover. Remove the  
d. Take out the drum unit and toner  
f. Hold the drum unit and toner cartridge  
assembly level with both hands and  
gently shake it from side to side  
several times to distribute the toner  
evenly inside the cartridge.  
2
3
4
DO NOT plug in the AC power cord yet.  
Front Cover  
Open  
Back Cover  
Open2  
Service Call  
Error2  
silica gel pack a.  
cartridge assembly.  
Jam Inside2  
No Paper  
Jam Rear2  
a. Remove the packing tape from the outside of the machine.  
Back Cover  
Toner  
b. Open the MP tray a, and remove the packing tape b from the MP tray  
support, then close the MP tray.  
Drum  
e. Remove the orange protective  
material from the drum unit and toner  
cartridge assembly.  
g. Put the drum unit and toner cartridge  
Paper  
assembly firmly back in the machine.  
CAUTION  
h. Close the front cover of the machine.  
Error  
DO NOT eat the silica gel pack. Please throw away. If ingested, seek medical attention  
immediately.  
Ready  
1 The LED will blink ON and OFF at 1 second intervals.  
2 The LED will blink ON and OFF at 0.5 second intervals.  
3 The yellow LED will blink in a pattern of ON for 2 seconds and then OFF for 3 seconds.  
The machine continues printing until the LED indicates the replace toner message.  
Load paper in the paper tray  
Options  
The machine has the following optional accessories. You can expand the capabilities of the machine by adding  
these items. For more information about the optional Lower Tray Unit and compatible SO‑DIMM Memory, visit us at  
a. Pull the paper tray completely out of the machine.  
b. While pressing the green paper‑guide release lever a, slide the paper guides  
to fit the paper size you are loading in the tray. Make sure that the guides are  
firmly in the slots.  
d. Put the paper in the tray and make sure:  
e. Put the paper tray firmly back in the machine. Make sure that it is completely  
Note  
The paper is below the maximum paper mark (▼▼▼) a. Over filling the  
paper tray will cause paper jams.  
inserted into the machine.  
For Legal or Folio size paper, press the  
release button a in the bottom of the  
paper tray and then pull out the back of  
the paper tray. (Legal or Folio size paper  
are not available in some regions.)  
f. Lift up the support flap a to prevent paper from sliding off the face‑down output  
The side to be printed on is face down.  
The paper guides touch the sides of the paper so it will feed properly.  
For installing the SO‑DIMM Memory, see Installing extra memory in the User’s Guide.  
tray.  
Lower Tray Unit for HL-5440D and HL-5450DN  
SO-DIMM Memory (HL-5450DN(T) only)  
LT‑5400  
You can increase the memory by installing one  
SO‑DIMM (Small Outline Dual In‑line Memory  
Module).  
The lower paper tray unit can hold up to 500 sheets of  
paper. When the tray is installed, the machine expands  
total input capacity up to 800 sheets.  
c. Fan the stack of paper well to avoid paper jams and misfeeds.  
For more information about recommended paper, see Recommended paper and print  
media in the User’s Guide.  
Print a test page  
Consumables  
When the time comes to replace consumable items, an error will be indicated by the LEDs on the control panel. For  
more information about the consumables for your machine, visit us at http://www.brother.com/original/ or contact  
your local Brother reseller.  
Important  
b. Turn the machine’s power switch on.  
d. Press Go. The machine will print a test page. Check that the test page has  
DO NOT connect the Interface cable yet.  
printed correctly.  
Toner cartridge  
Drum unit  
a. Connect the AC power cord to the machine and then connect it to an AC power  
outlet.  
c. After the machine has finished warming up, the Ready LED stops blinking and  
stays green.  
For replacing the consumable items, see Replacing consumable items in the User’s Guide.  
Note  
This function will not be available after the first print job you send from your computer.  
Turn the sheet over to install the printer driver.  

Xerox Workcentre 5225 User Manual
Sprint Nextel Samsung M320 User Manual
Soleus Air Air Conditioner Hp1 15 50 User Manual
Sanyo 26ks72r User Manual
Panasonic Cw A121vr User Manual
MAYTAG MMV6190FW 02 User Manual
MAKITA UH005G User Manual
LG G3 BEAT LG D722K User Manual
LG E1951T User Manual
LEVOIT LV RH131S User Manual