BLAUPUNKT WOODSTOCK DJ A User Manual

Radio / Cassette / Changer  
Coburg RCM 127  
Casablanca RCM 127  
Cannes RCM 127  
Woodstock DJ I  
Woodstock DJ A  
Operating instructions  
Contents  
Quick reference ............................ 28  
Scrolling through the broadcasting  
Adjusting the volume for traffic  
networks................................................ 37 announcements and the beep tone...... 43  
Important notes ............................ 33  
Changing the memory bank ................. 37  
Tape operation ............................. 43  
Storing stations ..................................... 37  
Precautions ........................................... 33  
Traffic safety ......................................... 33  
Installation............................................. 33  
Sound source mute .............................. 33  
Accessories .......................................... 33  
Inserting a tape ..................................... 43  
Automatically storing the strongest  
Removing a tape................................... 43  
stations with Travelstore....................... 38  
Fast Forward/Rewind ........................... 43  
Recalling stored stations ...................... 38  
Selecting titles with CPS ...................... 43  
Scanning stored stations with  
Switching the tape side (autoreverse).. 44  
Preset Scan .......................................... 38  
KeyCard theft protection system 34  
Tape equalisation ................................. 44  
Scanning cassette titles with SCAN ..... 44  
Listening to the radio during  
fast tape winding with RM .................... 44  
Care notes ............................................ 44  
Scanning stations with Radio-Scan...... 38  
Putting the unit into operation .............. 34  
Removing the KeyCard ........................ 34  
“Training” a second KeyCard/  
Replacing a KeyCard............................ 34  
Displaying the radio pass data ............. 34  
Short Additional Memory (S.A.M.)........ 35  
Turn On Message (T.O.M.) .................. 35  
Optical indication of anti-theft  
Selecting the seek tuning sensitivity .... 39  
Switching from stereo to mono............. 39  
Loudness .............................................. 39  
PTY Programme-Type....................... 39  
Switching PTY on/off ......................... 39  
Programme type ................................... 39  
Checking the programme type of the  
station ................................................ 40  
Displaying the selected programme  
type .................................................... 40  
Selecting a programme type ............. 40  
Storing programme types.................. 41  
Scanning stations with PTY-SCAN ... 41  
PTY priority........................................ 41  
CD changer operation.................. 45  
Switching to the CD changer mode...... 45  
Selecting CDs and titles ....................... 45  
MIX playback ........................................ 45  
Selecting the display mode .................. 46  
SCAN .................................................... 46  
protection .............................................. 35  
Care of your KeyCard ........................... 35  
Switching the audio source ........ 35  
DSC programming ....................... 47  
Radio operation with RDS ........... 36  
Overview of DSC factory settings ........ 49  
AF - Alternative frequency .................... 36  
REG - regional programme .................. 36  
Selecting a waveband  
(only Casablanca RCM 127,  
Cannes RCM 127, Woodstock DJ A) ... 36  
Station tuning ........................................ 37  
Appendix ....................................... 49  
Receiving traffic programme  
stations with RDS-EON................ 42  
Specifications........................................ 49  
Blaupunkt telephone hotline ................. 49  
Traffic announcement priority on/off .... 42  
Beep tone ............................................. 42  
Switching off the beep tone............... 42  
Automatic seek tuning start .................. 42  
Automatic tuning  
/
....................... 37  
Manual tuning with << >>.................. 37  
27  
Quick reference  
Switching on/off via the ignition:  
When connected correspondingly, the  
set can also be turned on and off with  
the vehicle ignition.  
After the ignition has been switched  
off, a double beep tone will remind you  
that you should remove the KeyCard  
before leaving your vehicle.  
3
1 Switching on/off with the ON button:  
Press ON.  
For instantly muting the volume.  
By pressing the  
button the volume  
When switching the set on with the ON  
button, the KeyCard has to be insert-  
ed. The unit will play with the pre-ad-  
justed volume.  
can be muted immediately. MUTE”  
will appear in the display.  
The function is cancelled by pressing  
button  
or VOL+.  
When pressing VOL-, the  
(mute)  
volume will be adopted.  
Switching on with the ignition being  
switched off:  
To programme the mute volume level,  
proceed as follows:  
To keep on operating the set when the  
ignition is switched off (KeyCard is in-  
serted), proceed as follows:  
Press ON. The unit will be turned on.  
To avoid that the battery goes flat, the  
system will be turned off automatically  
after one hour of playback.  
Adjust the desired volume.  
Press for 1 second until you  
hear a beep.  
Switching on/off with the KeyCard:  
The set has to be turned on with the  
ON button.  
Now this volume level is stored as your  
mute volume.  
Note:  
Read the information in chapter  
KeyCard theft protection system.  
2 VOL+ / VOL-  
To alter the volume.  
Each time the set is switched on, it will  
play with the pre-adjusted volume  
(VOL FIX).  
You may also change the VOL FIX set-  
ting (see chapter DSC programming).  
28  
4 Rocker switch  
Changer operation  
5 Display  
Optional:  
Coburg RCM 127, Casablanca  
RCM 127, Cannes RCM 127  
Included in scope of delivery:  
Woodstock DJ I, Woodstock DJ A  
a
e
d
f g h i j k  
l
CD selection  
Up  
b
c
Down  
Radio operation  
Title selection  
/
Station search  
Up  
Down  
Upwards: Press briefly.  
CUE - fast advance (audible):  
Keep depressed.  
a) NDR1 NDS - Station name  
<</>> Up/Down in short intervals  
(on FM only if AF is off)  
b) TR 1  
- Track (side) 1 of the cas-  
Downwards: Press as many times  
as required.  
sette  
c) 1 : 52  
- Playback TIME or disc  
NUMBER during CD  
changer operation  
- Waveband  
- Preset button (1-6)  
- Memory bank I, II or  
Travelstore  
- Seek tuning sensitivity  
- Alternative frequency for  
RDS operation  
To re-start a title: Press briefly.  
REVIEW - fast reverse (audible):  
Keep depressed.  
On FM only:  
<</>> To scroll through the station net-  
works when AF is on, e.g.NDR 1, 2,  
3, 4, N-JOY, FFN, ANTENNE ...  
d) FM  
e) 5  
f) I, II, T  
Extra rocker switch functions:  
Further setting functions with  
Tape operation  
AUD  
B
A
@
g) lo  
h) AF  
DSC Mode  
PTY  
/
Title selection (S-CPS)  
Up  
Condition: The corresponding function  
is activated.  
i) TP  
- A traffic station is being  
received  
- Priority for traffic stations  
- Loudness  
Down  
Fast forward  
Fast rewind  
j) TA  
k) LD  
l) PTY  
Stop function by pressing the opposite key.  
- Programme type function  
29  
6 KeyCard theft protection system  
To operate the set it is necessary that  
the KeyCard is inserted.  
7 FMT (Coburg RCM 127,  
Woodstock DJ I)  
8 AF  
Alternative frequency during RDS op-  
BND (Casablanca RCM 127,  
Cannes RCM 127, Woodstock DJ A)  
For selection of the FM memory banks  
I, II and T (Travelstore).  
eration:  
When AFlights up in the display, the  
system will automatically seek a fre-  
quency offering better reception of the  
same RDS programme.  
KeyCard  
To switch over:  
Press button repeatedly.  
The selected memory bank will appear  
in the display.  
AF on/off: Press AF briefly.  
Inserting the KeyCard  
Regional function on/off:  
With the KeyCard tongue sticking out  
of the unit, introduce the KeyCard into  
the slot with the contact area show-  
ing up.  
To remove the card, press first to un-  
lock.  
Press the AF button for approximately  
1 sec. until you hear a beep. REG-  
ONor REG-OFFwill appear in the  
display (see chapter REG - regional  
programme).  
Travelstore  
To store and recall the six most power-  
ful stations with Travelstore.  
To store: Press button for approxi-  
mately 1 sec. until you hear a beep  
and T-STOREappears in the display.  
To recall: Select the memory bank T”  
and press the corresponding preset  
button (1-6) briefly.  
Read also the information in chapter  
KeyCard theft protection system.  
9 TA (priority for traffic announcements)  
When TAlights up in the display, the  
system will play traffic stations only.  
Priority on/off: Press TA.  
Flashing KeyCard tongue  
When the radio is turned off and the  
KeyCard removed, the KeyCard  
tongue can be programmed to flash  
for optical theft protection.  
For more information see chapter  
DSC programming.  
This flashlight can be switched off by  
pushing in the tongue and lock.  
WRONG KCwill briefly appear  
on the display and the set will switch  
off automatically.  
Casablanca RCM 127,  
: 1, 2, 3, 4, 5, 6 - preset buttons  
You can store six stations for each of  
the memory banks I, II and T.  
Cannes RCM 127, Woodstock DJ A:  
Additional selection of medium- and  
long-wave stations, provided that AM  
ONhas been adjusted in the DSC  
menu.  
To store a station: Press a preset  
button during radio operation and hold  
down until the set resumes play after  
the muting and you hear a beep.  
To recall a station: Select the desired  
memory bank and press the relevant  
preset button briefly.  
30  
Extra function of preset buttons  
To store and recall a PTY programme  
type.  
Extra function of lo button:  
To switch between mono and stereo  
reception:  
? SC  
Radio operation  
When PTY is active (PTYlights up in  
the display), you can store and recall  
one programme type on/from each  
preset button on FM.  
Press button for approximately 1 sec.  
(beep).  
The selected condition will be briefly  
displayed.  
Scan  
Press SC briefly.  
The scanned frequency or the station  
name will start flashing in the display.  
During the actual scanning process  
FM-SCANor AM-SCANwill be dis-  
played. The unit will scan all FM sta-  
tions which can be received.  
; SRC (Source)  
=
/
You can switch between the radio,  
tape and CD changer operating  
modes, provided that a cassette/CD is  
inserted.  
To switch the tape side: Press briefly.  
To eject the tape: Press for approxi-  
mately 1 sec.  
Preset Scan  
Press SC for approximately 1 sec. until  
you hear a beep.  
SCANand the name or frequency of  
the scanned station will alternately ap-  
pear in the display.  
Extra function  
/
Frequency display during radio opera-  
tion:  
Press button briefly.  
< lo  
To switch the seek tuning sensitivity  
level:  
Press button briefly.  
The frequency will be briefly displayed.  
The unit will scan all stations stored on  
the preset buttons.  
If lois displayed, the radio will only  
pick up strong, local stations (normal  
sensitivity).  
> Cassette loading slot  
Insert the tape with side A or 1 facing  
To stop Scan / Preset Scan:  
Press SC once again.  
If lodoes not light up, the radio will  
also pick up weaker, distant stations  
(high sensitivity).  
up, the open side showing to the right.  
31  
Tape operation  
A DSC (Direct Software Control)  
Use the DSC function to customise  
certain programmable, basic settings  
to suit your personal needs and prefer-  
ences. See chapter DSC program-  
mingfor more information.  
The last setting will be stored automat-  
ically.  
To switch off AUD: Press button once  
again.  
If the setting remains unchanged with-  
in 8 seconds, the display will switch  
back to the previous condition.  
Cassetten-Scan  
Press SC.  
CC-SCANwill appear in the display.  
All cassette titles will be scanned brief-  
ly.  
To stop cassette scan:  
Press SC once again.  
B AUD  
Extra function AUD  
To adjust the treble, bass, balance and  
Loudness - When listening at a low  
level, the Loudness function creates a  
more natural sound by boosting  
the low frequency range.  
Loudness on/off: Press AUD for ap-  
proximately 1 sec.  
LDlights up in the display if the  
Loudness function is switched on.  
Please refer to chapter DSC program-  
mingfor more information on how to  
program the Loudness boost.  
fader.  
Changer operation  
If the display shows TREor BAS,  
you can adjust the reproduction of the  
treble and bass frequencies with the  
rocker switch. If BALor FADis dis-  
played, you can set the balance (left/  
right) and fader (front/rear).  
Press AUD as many times as required  
and make the setting using the rocker  
switch.  
CD-Scan  
Press SC briefly.  
CDC-SCANwill appear in the dis-  
play.  
All CD titles will be scanned briefly.  
To stop CD-Scan:  
Press SC once again.  
@ PTY (Programme Type)  
In the PTY mode, the preset buttons  
become programme type buttons. With  
every preset you can select one pro-  
gramme type, such as for example  
NEWS, SPORT, POP MUSIC, EDU-  
CATE, etc.  
Treble + / Fader front  
Treble / Fader rear  
Bass / Balance left  
Bass + / Balance right  
32  
Important notes  
Installation  
Accessories  
Precautions  
If you would like to install your new car ster- Use accessories and spare parts approved  
eo yourself or add other audio components by Blaupunkt only.  
Before starting to use your new car radio,  
please read the following information care-  
fully.  
to existing ones, then please read carefully  
the enclosed instructions on installation and  
ucts with this car radio:  
connection.  
You can use the following Blaupunkt prod-  
Traffic safety  
In order to ensure that the set operates prop-  
Amplifier  
Traffic safety always has the highest priori-  
ty.  
erly it is necessary that the positive power  
All Blaupunkt amplifiers, the preamp-out  
supply line is connected to the ignition and  
cable 7 607 893 093 is required.  
As the driver of a motor vehicle, it is your  
responsibility to pay attention to the traffic  
situation at all times. Never use your car  
radio in a way that could distract you.  
Please keep in mind that you travel a dis-  
tance of 14 m per second at a speed of only  
50 km/h.  
Should the traffic situation become particu-  
larly demanding, we advise you not to use  
the radio.  
Always make sure that you are still able to  
hear any warning signals coming from out-  
side of the vehicle, such as police or fire  
engine sirens, so that you can react accord-  
ingly.  
the permanent +12 V lead.  
Do not ground the loudspeaker outputs!  
Changer  
CDC A 05/F 05  
Telephone mute  
(adapter cable 7 607 889 093 is required),  
If there is a mobile telephone installed in your  
vehicle, the radio, tape player or CD player  
can be muted automatically when the phone  
is being used.  
CDC A 06  
(Woodstock DJ I, Woodstock DJ A):  
CDC A 06 included in the delivery.  
PHONEwill then appear in the display.  
When TA is active, traffic messages will al-  
ways have priority. The announcement will  
be aborted by pressing the TA button.  
Remote control  
With the infrared remote control RC 06 you  
can control all of the important functions of  
your car radio system from the steering  
wheel.  
Therefore, you should always select a mod-  
erate volume for playing your car radio while  
you are driving.  
33  
KeyCard theft protection system  
This car radio is supplied with one KeyCard The system will switch off after approximate-  
as standard, though it can also be operated ly 10 seconds.  
Push in the KeyCard. The card is re-  
leased and put in the proper position  
for being removed.  
with a second card.  
When inserting another card type (e.g.  
If you have lost your KeyCard or if it was phone or credit card), the display will show  
damaged, you can buy a new one from your WRONG KCfor approximately 2 seconds.  
Remove the first KeyCard and insert  
the new one.  
specialised dealer.  
The set will switch off automatically.  
After the display indication READYor  
LEARN KC,  
When using a second KeyCard, the settings Remove the wrong card and introduce the  
stored on the first card will be adopted. How- correct KeyCard.  
press DSC.  
ever, you can individually store the follow-  
ing functions:  
Press ON to turn on the set.  
Now you can also use the new KeyCard for  
operating your unit.  
A maximum of two cards can be used for  
the set.  
When trying to traina third one, the ac-  
cess authorisation for the KeyCard not used  
for the trainingprocess will be deleted au-  
tomatically.  
Bass, treble, balance and fader settings,  
Loudness, TA (traffic announcement vol-  
ume), beep volume.  
Removing the KeyCard  
Never pull out the KeyCard directly!  
In addition, the settings activated before  
switching the radio off, such as the station  
tuned in, TA priority, AF, AM ON/OFF and  
RM ON/OFF will also remained stored.  
This ensures that you will find your basic  
settings re-adjusted automatically as soon  
as you have inserted your KeyCard.  
First, slightly push in the KeyCard.  
This releases the card and puts it in the prop-  
er position for being removed.  
Now you can pull it out.  
Displaying the radio pass data  
Traininga second KeyCard/  
Replacing a KeyCard  
Using the KeyCard supplied with your set  
you can have the radio pass data such as  
the model name, product number (7 6..) and  
serial number indicated on the display pan-  
el.  
Putting the unit into operation  
While operating the unit with the first  
KeyCard, you can traina second one to  
be also used with the set:  
Turn on the set.  
With the KeyCard tongue sticking out,  
introduce the KeyCard into the slot  
with the contact area showing up.  
Please refer to chapter DSC programming  
- READ KC.  
Insert the first KeyCard and turn on the  
set.  
Press the DSC button and select  
The car radio is now ready for operation.  
If a wrong KeyCard is inserted, then CARD  
ERRfollowed by WAITwill appear in the  
display. In this case please do not make any  
further adjustments.  
LEARN KCwith  
/
.
Press << or >>.  
The display will switch to CHANGE.  
34  
Switching the audio source  
Short Additional Memory  
(S.A.M.)  
Optical indication of anti-theft  
protection  
Using the SRC button you can switch be-  
tween the following audio sources:  
radio,  
tape,  
Using the second KeyCard to be purchased Flashing KeyCard tongue  
at any specialised dealership, you can pro-  
When the vehicle is stationary and the  
gram a short text by selecting the DSC menu  
item READ KC. This text will be moved  
through the display and might be the tele-  
phone number of a car repair service or the  
emergency call number of your auto club.  
Any specialised dealer with the proper  
equipment can program the desired text with  
up to a maximum of 162 characters onto the  
KeyCard.  
KeyCard removed, the KeyCard tongue can  
be switched to flash for extra anti-theft se-  
curity.  
For this it is necessary that the positive pow-  
er supply line and the permanent +12 V lead  
are connected such as described in the in-  
stallation instructions.  
changer (optional for Coburg RCM  
127, Casablanca RCM 127 and  
Cannes RCM 127).  
Tape/changer operation is only available if  
a cassette/disc is inserted.  
To switch to another source,  
press SRC briefly.  
Be sure that LED ONis adjusted in the  
DSC mode.  
If required, please refer to chapter DSC  
programming - LED.  
Turn On Message (T.O.M.)  
Using the second KeyCard to be purchased  
at any specialised dealership, you can pro-  
gram the unit to display a selected Turn On  
Messageafter the set is switched on.  
Any specialised dealer with the proper  
equipment can program the desired text with  
up to a maximum of 48 characters onto the  
KeyCard.  
Switching off the flashlight  
The flashlight can be switched off by push-  
ing in the KeyCard and lock.  
If you would like to deactivate the flashing  
tongue with general effect, adjust the rele-  
vant item in the DSC menu to LED OFF.  
Each time you switch on your car radio us-  
ing the second KeyCard, this text will ap-  
pear in the display.  
Care of your KeyCard  
In order to ensure that the KeyCard always  
functions correctly, it is important for the  
contacts to be free from any foreign parti-  
cles. Avoid direct skin contact.  
If necessary, clean the KeyCard contacts  
using a cotton swab dipped in alcohol.  
35  
Radio operation with RDS (Radio Data System)  
The Radio Data System offers you more switching on the radio or recalling one of the If you leave the service area of the regional  
convenience when listening to FM radio sta- stored frequencies, the unit is automatically programme tuned into, or if you would like  
tions.  
searching for an alternative frequency.  
to take advantage of the full RDS service,  
More and more radio stations have begun SEARCHwill disappear from the display switch to REG OFF.  
to broadcast RDS information alongside when the alternative frequency has been  
their programmes. found or after the frequency band has been  
Press the AF button for approximately  
1 sec. until REG OFFappears.  
As soon as a programme has been identi- run through completely.  
fied, the station name including a regional If the reception quality of the selected pro-  
identifier, if applicable, will appear in the dis- gramme becomes too bad:  
If the REG function is active, REG ONwill  
be briefly displayed each time the radio is  
switched on.  
play, for example, NDR1 NDS (regional pro-  
gramme in Lower Saxony, Germany).  
When RDS is activated, the preset buttons  
become programme buttons. You now know  
exactly which programme you have tuned  
into, making it easy to find the desired sta-  
tion quickly.  
Tune into another station.  
Selecting a waveband  
(only Casablanca RCM 127,  
Cannes RCM 127, Woodstock DJ A)  
REG - regional programme  
Certain radio programmes are split up at  
times into regional programmes offering lo-  
cal information. The 1st programme broad-  
cast by NDR, for example, offers pro-  
grammes with different contents in the north-  
ern states of Germany Schleswig-Holstein,  
Hamburg and Lower Saxony at certain times  
of the day.  
If you are listening to one regional pro-  
gramme and move to an area where anoth- Note:  
er linked regional programme becomes In the DSC menu you can deactivate the  
stronger, the unit will switch to that pro- station selection on either MW or LW or for  
gramme.  
You can select between the following wave-  
bands:  
FM 87.5 - 108 MHz  
MW 531 - 1602 kHz  
LW 153 - 279 kHz  
But RDS offers you further advantages:  
AF - Alternative frequency  
Press the BND button until the desired  
The AF (Alternative Frequency) function  
makes sure that the strongest frequency of  
the currently selected programme is always  
tuned in automatically.  
This function is activated when AFappears  
in the display.  
waveband shows on the display panel.  
both wavebands at the same time.  
In order to switch this function on or off,  
If you wish to continue listening to the first This has the advantage that only the re-  
programme,  
press the AF button for approximately  
quired bands will allow to be activated, so  
that you must press the BND button less  
often. For more information, please refer to  
chapter DSC programming - AM ON/OFF.  
press the AF button briefly.  
While searching for the strongest reception  
signal, the radio may switch to mute briefly.  
If SEARCHappears in the display when  
1 sec.  
REG ONappears in the display.  
36  
Station tuning  
Manual tuning:  
Changing the memory bank  
Press << >>; the frequency will change  
in short intervals in downwards or up-  
wards direction.  
Automatic tuning  
/
You can shift between the memory banks I,  
II and T in order to store stations and recall  
them later.  
The currently selected memory bank is in-  
dicated in the display.  
Press  
cally search for the next station.  
When keeping the upper or lower part  
/
; the car radio will automati-  
When holding the right or left part of the rock-  
er switch depressed, the frequency scan is  
speeded up.  
/
of the rocker switch depressed, seek tuning  
will speed up in upwards or downwards di-  
rection.  
Press the FMT or BND button as many  
times until the desired memory bank  
lights up in the display.  
Scrolling through the broadcast-  
ing networks  
You can use the << >> buttons to tune in Storing stations  
stations of your reception area.  
On FM, you can store six stations on the  
preset buttons 1-6 for each of the memory  
banks I, II and T.  
On MW/LW, you can also store six stations  
each. (only with Casablanca RCM 127,  
Cannes RCM 127, Woodstock DJ A)  
If several programmes of the broadcasting  
networks can be received, you can scroll  
through them in forwards direction pressing  
>>, or backwards using the << button, e.g.  
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...  
For this it is necessary that the stations have  
been tuned in at least once and that AFis  
active (lights up in the display).  
Seek tuning  
Up  
Down  
Down in short intervals  
(AFmust be switched off)  
Up in short intervals  
(AFmust be switched off)  
Select the desired memory bank.  
Tune in a station with the rocker switch  
(either automatically or manually).  
For this purpose, you may start Travelstore  
seek operation:  
Press and hold down the desired pre-  
set button until the radio resumes play  
after the muting (takes approximately 1  
sec., confirmed by beep).  
Press FMT or BND for 1 sec.; the  
system starts to run through the fre-  
quency band. The display shows  
T-STORE.  
Manual tuning with << >>  
You can also tune in a station manually.  
Condition:  
Now the station has been stored.  
AF and PTY must be switched off (i.e. the  
symbols do not light up in the display).  
If AFdoes not light up,  
press AF.  
The activated preset button is indicated in  
the display.  
If necessary, deactivate these functions:  
This fulfils the requirements for selecting  
stations with << >>.  
Press AF or PTY briefly.  
37  
Notice:  
Recalling stored stations  
Scanning stations with Radio-  
Scan  
Should you tune in a station which has al-  
ready been stored before, then the corre-  
sponding preset position and memory bank  
will briefly flash in the display.  
You can recall any stored station at the touch  
of a button.  
You can also scan all stations which can  
currently be received.  
Select the memory bank with FMT or  
BND.  
To start the Scan function:  
Press the corresponding preset button  
briefly to recall the station.  
Press SC briefly.  
Automatically storing the  
strongest stations with  
Travelstore  
The scanned frequency or the station name  
will start flashing in the display. During the  
actual scanning process FM-SCANor  
AM-SCANwill be displayed.  
Scanning stored stations with  
Preset Scan  
You can automatically store the six most  
powerful FM stations of your current recep-  
tion area sorted according to their signal  
To select a scanned station and switch  
off Radio-Scan:  
You can have all of the stored stations briefly  
strength. This function is particularly conven- scanned on all wavebands.  
Press SC briefly.  
ient on longer trips.  
To start Preset Scan:  
If no station is selected, the scan function  
will be automatically switched off after the  
frequency band has been run through com-  
pletely. The unit will tune in the station lis-  
tened to before starting the scan.  
Press the FMT or BND button for  
Press SC for approximately 1 sec.  
1 sec.  
All of the stored stations to be received will  
be scanned one after the other.  
T-STOREwill appear in the display.  
The six strongest FM stations will be auto-  
matically stored on the memory bank T”  
(Travelstore). When this process has been  
completed, the radio will play the first sta-  
tion stored on preset 1.  
If desired, stations can also be stored man-  
ually on the Travelstore bank (see Storing  
stations).  
To select a scanned station and switch  
off Preset Scan:  
Press SC briefly.  
Note:  
If TAshows on the display panel, the sys-  
tem will scan the stored traffic stations only.  
38  
Selecting the seek tuning sensi- Loudness  
tivity  
Programme type  
Adjusts the low bass frequencies for a more Use << >> to have the last selected pro-  
You can alter the automatic seek tuning natural sound.  
gramme type displayed and to choose a new  
one.  
sensitivity.  
Switching Loudness on/off:  
If lois displayed, the radio will only pick up  
strong, local stations.  
If lodoes not light up, the radio will also  
pick up weaker, distant stations.  
You can select any one of the stored types  
with the preset buttons 1-6.  
Condition: PTY must be active.  
Using DSC you can choose between Ger-  
man and English (see DSC programming -  
PTY LANG).  
All of the programme types listed below are  
available.  
The letters printed in bold are identical to  
the actual short-time indication in the dis-  
play.  
Press the AUD button for approximate-  
ly 1 sec.  
When the Loudness function is active, LD”  
will light up in the display.  
See chapter DSC programmingfor more  
information.  
To switch the seek tuning sensitivity:  
Press lo briefly.  
The sensitivity level can be altered sepa-  
rately in both modes. Please refer to chap-  
ter DSC programming - S-LO, S-DX).  
PTY Programme-Type  
PTY is an RDS service offered by more and  
more radio broadcasters. This feature allows  
you to select FM stations according to their  
programme type. After you have chosen the  
PTY of your preference, the corresponding  
stations can be selected either by seek tun-  
ing or using the scan function.  
Switching from stereo to mono  
NEWS  
Every time the radio is switched on, stereo  
playback is activated automatically.  
The unit will gradually switch to mono if re-  
ception is poor.  
You can also switch between mono and ster-  
eo reception manually:  
CURRENT AFFAIRS  
INFORMATION  
SPORT  
EDUCATE  
DRAMA  
CULTURE  
Switching PTY on/off  
Press the lo button for approximately  
1 sec.  
SCIENCE  
VARIED  
POP MUSIC  
ROCK MUSIC  
M.O.R. M (middle of the road music)  
LIGHT M (light classical)  
CLASSICS (serious classical)  
Press PTY.  
When the function is active, the programme  
type selected last will briefly appear in the  
display. PTYwill be permanently indicat-  
ed in the lower right corner of the display  
panel.  
The selected condition will briefly appear in  
the display.  
39  
OTHER M (other music)  
WEATHER  
Displaying the selected programme  
type  
b) Using the << >> buttons of the rocker  
switch  
FINANCE  
When PTY is switched on, you can se-  
lect a programme type using buttons  
<< >>.  
Press << or >>.  
CHILDRENS PROGRAMMES  
SOCIAL AFFAIRS  
RELIGION  
PHONE IN  
TRAVEL  
The programme type selected last will be  
displayed briefly.  
Press << or >>; the programme  
type selected last will be displayed  
for 3 seconds.  
Selecting a programme type  
a) Using the preset buttons  
HOBBIES  
JAZZ MUSIC  
During this period press >> (for-  
wards) or << (backwards) to select  
the desired type.  
When PTY is switched on, you can use  
the preset buttons 1-6 to select the  
programme types stored at the factory.  
COUNTRY MUSIC  
NATIONAL MUSIC  
OLDIES MUSIC  
FOLK MUSIC  
DOCUMENTARY  
ALARM TEST  
Press << or >> as many times as  
required.  
Press one of the presets 1-6.  
The selected programme type will be  
displayed for 2 seconds.  
If you wish to listen to a station offering  
the selected PTY,  
If you wish to listen to a station with  
this PTY,  
press  
/
to start seek tuning.  
Checking the programme type of the  
station  
If the system is unable to find a station of-  
fering the selected programme type, the dis-  
play will show NO PTYand a beep tone  
will be released. The station received be-  
fore starting seek tuning will be tuned in.  
press  
/
to start seek tuning.  
If the system is unable to find a station of-  
fering the selected programme type, the dis-  
play will show NO PTYand a beep tone  
will be released. The station received be-  
fore starting seek tuning will be tuned in.  
You can assign different programme types  
to each preset position. Please refer to chap-  
ter Storing programme types.  
Press PTY for approximately 1 sec.  
After the beep tone the display will show the  
programme type offered by the tuned in sta-  
tion.  
If NONEappears in the display, the cur-  
rent station has no PTY code.  
40  
Storing programme types  
PTY priority  
During tape operation, the set will also au-  
tomatically switch to the programme offer-  
ing the selected PTY within the broadcast-  
ing network.  
After the PTY programme the system will  
remain in the radio mode.  
At the factory, one programme type was Situation:  
assigned to each of the preset buttons 1-6.  
PTY is switched on and lights up in the dis-  
If desired, you can also store other availa-  
ble programme types.  
play.  
No station offering the selected programme  
type can be currently received (neither with  
seek tuning nor with scan).  
To do so, make sure that PTYlights up in  
the display.  
If necessary, press the PTY button to  
switch on the function.  
The set will switch back to the previous sta-  
tion.  
Notice:  
As mentioned earlier, these functions are  
currently only supported by a limited number  
of RDS stations.  
As soon as a programme with such PTY can  
be received within the broadcasting network,  
the unit will switch over to the correspond-  
ing station for the duration of the pro-  
gramme.  
Select a programme type using but-  
tons << >> and  
hold down the desired preset button  
(1-6) until you hear a beep.  
Now the selected programme type can be  
recalled by pressing this preset. For this, the  
PTY function must be active.  
Example: German broadcasting network  
NDR:  
-
-
-
-
-
Station tuned in: NDR3.  
Scanning stations with PTY-SCAN  
PTYlights up in the display.  
Programme type POPselected.  
Seek tuning is started.  
Condition: PTYmust appear in the display.  
Press the SC button.  
All of the received stations offering the se-  
lected programme type will be scanned.  
No station with PTY-POPcan be  
found.  
To switch off PTY-SCAN:  
Press SC once again.  
-
-
-
-
The display shows NO PTYand  
automatically switches back to NDR3.  
NDR2 airs a PTY-POPprogramme.  
The system will switch to the linked  
NDR2 station for the duration of the  
POPprogramme.  
41  
Receiving traffic programme stations with RDS-EON  
The abbreviation EONstands for En- Traffic announcement priority  
Switching off the beep tone  
hanced Other Networks, meaning the ex- on/off  
a) Tune into another station offering traf-  
fic information:  
change of information within a radio network.  
If the priority for traffic announcement pro-  
Many FM broadcasters offer traffic messag-  
grammes is activated, TAwill light up in  
es for their service area at regular intervals.  
the display.  
Press the rocker switch or  
press a preset button which has a  
traffic programme station allocated  
to it.  
All traffic programme stations transmit a  
special carrier signal alongside their pro-  
To switch the priority on or off:  
Press the TA button.  
grammes, which is decoded by your car ra-  
dio. If this signal is identified, TPwill ap- When pressing TA while a message is be-  
Alternatively:  
pear in the display (Traffic Programme).  
In addition to these, there are also stations  
ing broadcast, this message will be inter-  
rupted. The unit will then switch back to the  
b) Switch off the priority for traffic an-  
nouncements:  
which do not actually transmit traffic pro- previous condition. The priority for all other  
grammes themselves, but by using RDS- traffic messages remains active.  
Press TA.  
TAwill disappear from the display.  
EON they offer the possibility to receive the  
Please note that several buttons have no  
traffic messages broadcast by another traf- function while a traffic announcement is  
fic programme station in the same radio broadcast.  
network.  
Automatic seek tuning start  
(tape and CD changer operation)  
If you wish to have the priority for traffic an-  
nouncements activated while listening to  
one of these stations (e.g. NDR3), TAmust  
appear on the display panel.  
If a traffic announcement is broadcast, the  
radio will automatically switch to the linked  
traffic programme station (in this case,  
NDR2) for the duration of the message and  
return to the original programme (NDR3)  
afterwards.  
Beep tone  
When leaving the reception area of the tuned  
in traffic programme station while listening  
to a tape or CD, the system will automati-  
cally start searching for a new TA pro-  
gramme.  
If no such station is found within approxi-  
mately 30 seconds, you will hear a warning  
beep every 30 seconds. To switch off the  
beep tone proceed as described above.  
If you leave the reception area of the traffic  
programme station currently tuned into, you  
will hear a beep tone approximately every  
30 seconds.  
This tone will also be released when press-  
ing a preset button which has no traffic pro-  
gramme allocated to it.  
42  
Tape operation  
Adjusting the volume for traffic  
announcements and the beep  
tone  
Fast Forward/Rewind  
The car stereo has to be switched on.  
The unit will automatically switch to tape  
operation when inserting a cassette.  
This volume was preset at the factory,  
though you can alter the value using the  
DSC function (see DSC programming, TA  
VOL).  
If the volume level is altered while a mes-  
sage is being played, this will only affect the  
current announcement.  
Inserting a tape  
Turn on the set.  
Insert a tape.  
Fast forward  
Fast rewind  
The cassette will be automatically transport-  
ed to the playback position. Side A or 1 starts  
to play.  
/
Title selection (S-CPS)  
During tape operation, TR 1or TR 2”  
(track) will be indicated on the display pan-  
el.  
Up  
Down  
Stop function by pressing  
.
Insert the tape with side A or 1 facing up, the open side  
showing to the right.  
Selecting titles with CPS  
(Cassette Programme Search)  
Use this function to skip ( ) and repeat (  
recorded titles.  
)
To start CPS:  
Removing a tape  
Press  
/
.
In order for CPS to function properly, there  
has to be an unrecorded tape portion of at  
least 3 seconds between the individual ti-  
tles.  
Press  
The cassette will eject.  
for 1 sec.  
43  
Switching the tape side  
(autoreverse)  
Scanning cassette titles with  
SCAN  
Care notes  
To avoid possible problems, we recommend  
To change the tape direction during cassette You can have the cassette titles played brief- you to use C-60/C-90 type cassette tapes  
playback:  
Press  
At the end of a tape side the mechanism  
changes directions automatically to play the To start/stop the scan function:  
ly by using the scan function. If you like a only. Store your tapes in a cool place away  
title, stop the scan to continue listening to from dirt, dust and temperatures exceeding  
briefly.  
that track.  
50 °Celsius. Allow very cold tapes to warm  
up before playing them in order to avoid  
uneven tape transport. After approximately  
100 hours of use, dust particles collected  
on the playback head or roller may lead to  
tape run problems and sound distortions.  
Use a head cleaning tape to remove nor-  
mal dirt build-up. For tougher cases, use a  
cotton swab (Q-Tip) dipped in alcohol. Do  
not attempt to clean by inserting a hard ob-  
ject into the player!  
other side (autoreverse). The display shows  
Press the SC button briefly.  
TR 1for track (side) 1 or TR 2for track 2.  
Scan condition: There has to be an unre-  
corded tape portion of at least 3 seconds  
between the individual titles.  
Notice:  
If there is too much tension on the tape dur-  
ing playback, the set may switch over by it-  
self before having reached the end of the  
tape side. In this case check the condition  
of the cassette tape. Sometimes it helps to  
rewind it completely.  
Listening to the radio during  
fast tape winding with RM  
(Radio Monitor)  
When the tape is fast forwarded or rewound  
(also with CPS), the radio will normally be  
muted. In order to listen to the radio during  
fast winding, you can activate the Radio  
Tape equalisation  
When a metal or CrO2 tape is inserted, the Monitor function.  
tape mechanism automatically adjusts to For more information please refer to chap-  
metal/CrO2 tape equalisation.  
ter DSC programming - RM ON/OFF.  
44  
CD changer operation  
Selecting CDs and titles  
MIX playback  
Optional:  
Coburg RCM 127, Casablanca RCM 127,  
Cannes RCM 127  
You can have the CD tracks played in ran-  
dom order.  
Included in scope of delivery:  
Woodstock DJ I, Woodstock DJ A  
Select the desired MIX mode in the DSC  
menu.  
This piece of equipment offers you conven-  
ient control of a Blaupunkt CD changer CDC-  
A 05/F 05 (with adapter 7 607 889 093) /  
CDC-A 06.  
MIX CDC The MIX mode is active:  
The individual discs and the  
titles of the selected CD are  
chosen randomly. After all  
titles have been played, the  
next CD will be selected at  
random again.  
CD selection  
Up  
Down  
Note:  
Use only perfectly circular CDs.  
Title selection  
CDs manufactured in the shape of a butter-  
fly or a beer mug, for example, are not suit-  
able for use with this equipment.  
Using such CDs can very likely result in the  
destruction of the CD and the CD drive.  
We assume no responsibility for damages  
caused by using unsuitable CDs.  
Use to select a CD title in  
random order.  
Upwards: Press briefly.  
CUE - fast advance (audible): Keep  
depressed.  
MIX OFF The Mix function is deactivat-  
ed. Discs and titles will be  
Downwards: Press as many times as  
required.  
To re-start a title: Press briefly.  
REVIEW - fast reverse (audible):  
Keep depressed.  
selected in numeric order.  
To change the MIX mode:  
Press DSC.  
Switching to the CD changer  
mode  
Select MIXusing the rocker switch  
/
and adjust with  
/
.
If the function is active, CDC MIXwill be  
displayed every time CD changer operation  
is activated.  
Make sure that at least one CD has been  
inserted into the magazine.  
Press SRC to toggle the audio source:  
Press repeatedly until the CD functions  
appear in the display.  
45  
Selecting the display mode  
SCAN  
You can select the desired display mode for Use this function to scan all of the CD tracks.  
CD playback:  
To start the Scan function:  
CDC NUMBER” – The CD number, such  
Press SC.  
as CD 8is dis-  
played.  
The titles will be scanned one after the oth-  
er in ascending order.  
TIME”  
The elapsed playback  
time of the current title  
is displayed, for ex-  
ample 2 : 32.  
To stop the Scan function:  
Press SC briefly.  
The track currently being scanned is con-  
tinued to be played.  
SCAN will also be terminated by  
To switch the display mode:  
pressing one of the buttons AUD,  
Press DSC.  
GEO, DSC, SRC, << >> or / .  
Use the rocker switch  
CDC DISP.  
/
to select  
Use  
/
to adjust to NUMBERor  
TIME.  
You can also change the display mode im-  
mediately for the title currently playing by  
pressing  
.
46  
DSC programming  
MIX  
For changer operation only.  
RM ON / OFF (Radio Monitor)  
Allows you to listen to the  
DSC (Direct Software Control) allows you  
to customise certain programmable, basic  
settings to suit your personal needs and  
preferences and then store them.  
The basic settings for this audio equipment  
were made at the factory.  
In the following you can find an overview of  
these settings, so that you can always reset  
to these if desired.  
MIX CDC -  
radio during fast winding of  
the tape.  
RM ON Radio playback  
activated  
RM OFF Function deacti-  
vated  
CD selection at random.  
All titles of this disc will be  
chosen in random order as  
well.  
The next disc is again se-  
lected at random.  
MIX OFF -  
The MIX function is  
switched off.  
If you wish to alter any of the programming,  
LOUDNESS When listening at a low lev-  
el, the Loudness function  
creates a more natural  
sound by boosting the low  
frequency range.  
press SRC to choose the desired oper-  
ating mode (e.g. radio, if you wish to  
change the language with PTY LANG).  
AM ON / OFF (Casablanca RCM 127,  
Cannes RCM 127, Wood-  
stock DJ A)  
press DSC.  
LOUD 1 - Low boost  
LOUD 6 - Max. boost  
Use the rocker switch to select and adjust  
the functions described in the following. The  
display will show you the adjusted condition.  
You can deactivate one or  
both AM bands (MW/LW) in  
order to reduce the number  
of bands for selection with  
BND.  
TA VOL  
To adjust the traffic an-  
nouncement and beep tone  
volume from between 0 to  
63.  
selectable:  
The message will then come  
through at this volume, if the  
standard volume is lower.  
If the standard volume is  
higher than the TA VOL lev-  
el, the traffic report will be  
played slightly louder than  
the standard volume.  
AM ON all bands  
MW OFF LW, FM  
LW OFF MW, FM  
AM OFF FM  
/
Select function  
<< >>  
Adjust/recall value  
47  
BEEP  
Acknowledgement tone for  
all functions which require a  
button to be pressed for  
more than 1 second.  
The volume can be adjusted  
from between 0 to 9. (0 =  
off)  
READ KC  
To read out the KeyCard  
data.  
S-LO  
To adjust the seek tuning  
sensitivity for local recep-  
tion.  
LO 1 - high sensitivity  
LO 3 - low sensitivity  
The seek tuning sensitivity  
values can be set separately  
for AM and FM.  
The KeyCard supplied with  
the radio is used to display  
the model name, type  
number (7 6..) and the serial  
number.  
Using the second KeyCard  
to be purchased at any spe-  
cialised dealership it is pos-  
sible to display the Short  
Additional Memory (S.A.M.)  
data entered by the dealer.  
See chapter Short Addition-  
al Memory S.A.M..  
LED ON/OFF You can choose between  
LED ON or LED OFF. With  
LED ON, the KeyCard  
AUX ON/OFF Please note that this item  
will not appear if you have  
connected a CD changer.  
Default setting: AUX OFF.  
Adjust to AUX ON if you  
have connected an external  
piece of equipment to the  
AUX socket.  
tongue will flash for extra  
anti-theft protection when  
the unit has been switched  
off and the KeyCard re-  
moved.  
If you remove the KeyCard  
during the reading process,  
READ KCwill show on the  
display panel.  
LEARN KC To traina second  
KeyCard.  
VOL FIX  
Use this function to select  
the volume at which the ra-  
dio is set when it is switched  
on. Adjust the desired vol-  
ume level with << >>. When  
adjusted to VOL 0, the  
system will come on with the  
volume selected before  
switching it off.  
Please read the information  
in chapter KeyCard theft  
protection system - Training  
a second KeyCard.  
PTY LANG To select the programme  
type language: DEUTSCH  
or ENGLISH  
S-DX  
To adjust the seek tuning  
sensitivity for distant recep-  
tion.  
DX 1 - high sensitivity  
DX 3 - low sensitivity  
48  
Appendix  
To quit the DSC programming mode  
and store the adjustment:  
Specifications  
Blaupunkt  
telephone hotline  
Amplifier  
Press DSC.  
Output power:  
4 x 23 W RMS power  
acc. to DIN 45324 at  
14.4 V  
The DSC programming mode will be auto-  
matically quit 8 seconds after having made  
the last adjustment.  
Address of the next service  
centre in your vicinity  
(only for Germany)  
4 x 35 W max. power  
Tuner  
Wavebands:  
Overview of DSC factory set-  
tings  
If you would like to know the address of  
the next Blaupunkt service centre of  
your area without having our service list  
at hand:  
FM  
:
87.5 108 MHz  
MIX  
OFF  
(Casablanca RCM 127, Cannes RCM 127,  
Woodstock DJ A)  
RM  
OFF  
LOUDNESS  
TA VOL  
BEEP  
3
35  
4
MW  
LW  
531 1602 kHz  
153 279 kHz  
-
-
Find out your area code.  
Then call the following chargeable  
LED  
ON  
phone number: 01 80 / 5 25 56 66.  
FM sensitivity:  
0.9 µV at 26 dB signal-  
to-noise ratio  
LEARN KC  
READ KC  
PTY LANG  
S - DX  
S - LO  
VOL FIX  
-
-
-
Using the area code to be entered  
you will be automatically given the  
address and phone number of the  
next Blaupunkt service centre. You  
can also request this information  
by fax.  
ENGLISH  
FM frequency response:  
30 - 16 000 Hz  
1
1
0
Tape player  
(Casablanca RCM 127, Cannes RCM 127,  
Woodstock DJ A):  
Frequency response:  
30 - 18 000 Hz  
AM  
ON  
CD changer  
Frequency response:  
5 - 20 000 Hz  
Subject to modifications!  
49  

Sterling Power Products 1230ce User Manual
Sharp Ux Cc500 User Manual
Samsung Commercial Splittype Series Ns026nhxea User Manual
Metal Shed Instruction User Manual
LG 65US772M0UB User Manual
JVC DX T66UY User Manual
HP DESKJET INK ADVANTAGE 4530 User Manual
DELL C7520QT User Manual
CRAFTSMAN 247.370000 User Manual
ASUS ZEN AIO ZN242IF User Manual