KD975
KD985
KD990
A
B
C
E
3
D
F
4
3. Personal safety
Intended use
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
Your Black & Decker rotary hammer drill has been designed
for drilling in wood, metal, plastics, and masonry as well as for
screwdriving and light chiselling applications. This tool is
intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
@
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
4. Power tool use and care
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
5
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Additional power tool safety warnings
Warning! Additional safety warnings for rotary and
@
chiselling hammers
u Wear ear protectors. Exposure to noise can cause
hearing loss.
u Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Labels on tool
The following pictograms are shown on the tool:
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the operator.
u Never use a chisel accessory in rotary mode.
The accessory will bind in the material and rotate the drill.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present
a risk of personal injury and/or damage to property.
Warning! To reduce the risk of injury, the user must
read the instruction manual.
:
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
#
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Variable speed control knob
5. Drilling mode selector
6. Tool holder
Safety of others
u This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
7. Side handle
8. Depth stop
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
u Children should be supervised to ensure that they do not
play with the appliance.
6
Fitting the side handle and depth stop (fig. A)
u Turn the grip counterclockwise until you can slide the side
handle (7) onto the front of the tool as shown.
Use
Warning! Let the tool work at its own pace. Do not overload.
u Rotate the side handle into the desired position.
u Insert the depth stop (8) into the mounting hole as shown.
u Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the operating mode (fig. E)
The tool can be used in three operating modes. Rotate the
drilling mode selector (5) towards the required position, as
indicated by the symbols.
u Tighten the side handle by turning the grip clockwise.
Fitting an accessory (fig. B)
u Clean and grease the shank (9) of the accessory.
u Pull back the sleeve (10) and insert the shank into the tool
holder (6).
u Push the accessory down and turn it slightly until it fits into
the slots.
Drilling
u For drilling in steel, wood and plastics, and for screwdriving
u When screwdriving, start at a low speed. When removing
set the operating mode selector (5) to the rposition.
screws, the speed is automatically reduced.
u Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
u To remove the accessory, pull back the sleeve (10) and
pull out the accessory.
Hammer drilling
u For hammer drilling in masonry and concrete, set the
u When hammering, the tool should n
operating mode selector (5) to the sposition
ot bounce and run
smoothly. If necessary, increase the speed.
KD985/KD990 - Fitting the keyed chuck (fig. C)
u Fit the shank (11) of the supplied chuck (12) into the tool
holder as described above.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (5) to the
Warning! Never use keyed chucks in the hammer drilling mode.
u
qposition.
KD985/KD990 - Fitting accessories in the keyed
chuck (fig. D)
u Open the chuck by turning the sleeve (13).
u Insert the bit shaft (14) into the chuck.
u Insert the chuck key (15) into each hole (16) in the side of
the chuck and turn until tight.
u When changing from hammer drilling to chiselling, turn the
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Selecting the direction of rotation
For drilling, for tightening screws and for chiselling, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(3) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
Setting the drilling depth (fig. F)
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Slacken the side handle (7) by turning the grip
counterclockwise.
u Set the depth stop (8) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
7
Switching on and off
Protecting the environment
u To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
Set the variable speed control knob (4) to the required
speed range.
Separate collection. This product must not be
disposed of with normal household waste.
Z
u Use speeds 1-6 for short periods only.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
u As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
u For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only in forward (clockwise) rotation.
Separate collection of used products and packaging
u To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
z
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Technical data
KD975
TYPE 2
KD985
TYPE 2
230
800
0 - 980
KD990
TYPE 2
230
850
0 - 980
Input voltage
Power input
No-load speed
Impact rate
Impact energy
Max. drilling capacity
Concrete
Steel
Wood
Weight
VAC 230
710
min-1 0 - 980
min-1 0 - 5,180 0 - 5,180 0 - 5,180
W
J
1.8
2.2
2.4
mm 22
mm 13
mm 30
kg 3.4
24
13
30
3.4
26
13
30
3.4
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
Level of sound pressure according to EN 60745:
Sound pressure (L
u Connect the brown lead to the live terminal in the new plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
pA) 94 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 105 dB(A), uncertainty (K) 3 dB(A)
8
Vibration total values (triax vector sum) according to EN 60745:
Guarantee
Hammer drilling into concrete (ah, HD) 10.8 m/s2, uncertainty (K) 1.5 m/s2
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
Chiselling (ah, Cheq) 8.5 m/s2, uncertainty (K) 1.5 m/s2
EC declaration of conformity
MACHINERY DIRECTIVE
%
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
KD975/KD985/KD990
Black & Decker declares that these products described under
"technical data" are in compliance with:
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009), EN 60745-1, EN 60745-2-6
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
_
United Kingdom
1-11-2009
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
9
10
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
Slough, Berkshire SL1 3YD
90557455 REV-0
11/2009
|