COLD PAN REFRIGERATED AIR FLOW SYSTEM
WCM-BT SERIES
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately. See page 1.
DROP-IN COLD PAN
REFRIGERATED, AIR FLOW SYSTEM
SELF-CONTAINED WITH DEFROST SYSTEM
Effective Date: 2019
IMPORTANT INFORMATION
READ BEFORE USE
Project: ___________
Item No.:ꢀ ___________
Quantity:ꢀ ___________
DROP-IN SERVING EQUIPMENT
COLD PAN
WCM-BT-3
WCM-BT-4
WCM-BT-5
WCM-BT-6
Refrigerated
Air Flow System
Self-Contained with
Defrost System
WCM-BT-4
SPECIFICATIONS
STANDARD FEATURES
TOP: Constructed of 18 gauge, type 304 stainless steel, die
stamped with a raised perimeter bead. There shall be a solid
vinyl gasket under the beaded edge to form a seal to the
counter top, thus preventing seepage or marring of the
counter top. Embossed mounting lugs are provided along the
inner surface of the top to hold a full set of removable
separator channels in place.
g
Forced air evaporator blower system for maximum
efficiency in cooling - more consistent food product
temperature
g
g
Automatic Defrost System
Fully insulated for maximum efficiency and energy
savings
g Factory applied gasket - makes installation a snap and
seals units to the counter top, thus eliminating
seepage
g Accommodates standard 12”ꢀX 20”ꢀpans with the use
of separator channel(s), or fractional size pans with the
use of optional adapter bars
LINER: The inner liner shall be 18 gauge, type 304 stainless
steel, one piece construction, all welded, ground and polished
to a uniform finish. All corners are coved with a minimum 1/4"
radius.
INSULATION: The pan is fully insulated with high density
polystyrene, 1" thick on all sides, 2" thick on the bottom and
enclosed with a 22 gauge galvanized steel outer case.
g
1-Year Parts & Labor Warranty
UL Listed
g
REFRIGERATION SYSTEM: The compressor housing shall
be fabricated from 14 gauge galvanized and bolted to the
base of the unit. A fully self-contained condensing unit is pro-
vided with a hermetically sealed compressor and a thermostat
control. The system is also provided with a forced air evapora-
tor for even temperature throughout the pan that drains into a
condensate evaporator pre-wired in the unit. Automatic defrost
system is provided. The system is fully charged with CFC free
refrigerant and ready to operate.
ACCESSORIES
g
5YW - 5-Year Compressor Warranty
g Stainless Steel adapter bars (pg DI-51-52)
g Stainless Steel adapter plates (pg DI-51-52)
g
CP - Cover Plate with handles, S/S
g
RS - Remote on/off switch for counter mounting
g * 220 Volt - 50 Cycle Compressor
NOTE: Proper ventilation must be provided in counter.
ELECTRICAL: The unit will be wired for 15 amps., 120 volt,
single phase operation with an on/off thermostat switch and
pilot light. A 6' long, 3-wire cord and plug (NEMA 5-15P) will
be provided.
Specifications subject to change without notice.
*Please see Operation &ꢀInstallation Manual for ALL operation and maintenance details.
* Units with these accessories are not currently ULꢀlisted.
DI-27
REMOVABLE SEPARATOR
CHANNELS
A
4”
6”
8”
14”
16”
24”
20-1/8”
10-3/4”
B
21-1/2”
21-5/8”
4-7/8”
PLAN VIEW
ELEVATION
END VIEW
EVAPORATOR
ELECTRICAL
CHARACTERISTICS
6.8 amps. - 120V - 22-1/4” X 41-3/4”
1/4HP
CUT-OUT
SHIP WT.
(LBS.)
MODEL
“A”
“B”
PAN SIZE
REMOTE
LESS COMP.
REQUIRED
REFRIGERATION SHIP WT.
43-1/2”
6”
19-7/8” X 39-1/4 X 14”
228
MODEL
(LBS.)
WCM-BT-3
WCM-BT-4
WCM-BT-5
(110.4cm) (15.24cm) (50.4 X 99.6 X 35.5cm)
(56.5 X 106cm) (103.4kg)
180
(81.6kg)
222
WCM-BTX-3
57-1/4”
4-1/8”
19-7/8”ꢀX 53” X 14”
9.2 amps. - 120V - 22-1/4” X 55-1/2”
268
(145.4cm) (10.5cm) (50.4 X 134.6 X 35.5cm)
1/3HP (56.5 X 140.9cm) (121.5kg)
WCM-BTX-4
WCM-BTX-5
(100.6kg)
259
(117.4kg)
71” 7”
(180.3cm) (17.78cm) (50.4 X 169.5 X 35.5cm)
19-7/8” X 66-3/4” X 14” 9.2 amps. - 120V - 22-1/4” X 69-1/4”
311
1/3HP
(56.5 X 175.8cm) (141.1kg)
299
(135.6kg)
84-3/4” 7” 19-7/8” X 80-1/2” X 14” 9.2 amps. - 120V -
(215.2cm) (17.78cm) (50.4 X 204.4 X 35.5cm) 1/3HP
22-1/4” X 83”
345
WCM-BTX-6
WCM-BT-6
(56.5 X 210.8cm) (156.4kg)
REFRIGERATION CHART
LOW
PSIG.
10
HIGH
BTU
MODEL
HP
REF. OZ.
PSIG. M10 90A
WCM-BT-3 1/4
WCM-BT-4 1/3
WCM-BT-5 1/3
WCM-BT-6 1/3
134A
134A
134A
134A
8
170
190
160
125
1070
1285
1285
1285
10
10
10
9
9
9
WCM-BTX - REFRIGERATED COLD PAN WITHOUT
COMPRESSOR
COMPRESSORS FOR REMOTE INSTALLATIONS
Units include Refrigerated Cold Pan,
Thermostat, Cap Tube & Drier
2029-17JP - 1/4 HP for WCM-BTX-3
2029-27JL - 1/3 HPꢀfor WCM-BTX-4, 5 & 6
(for hook up in field by others)
Atlas Metal Industries 1135 NWꢀ159th Dr. Miami, FL 33169 (800) 762-7565 Fax: (305) 623-0475 atlasfoodserv.com
6/19-sc
DI-28
REFRIGERATED PAN WITH EVAPORATOR
BLOWER & TIMER
WCMBT SERIES
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
INSTALLATION
Provide the correct counter cut-out opening (see chart below) and drop in. The vinyl gasket assures complete seating. A
non-toxic silicone seal may be used between the gasket and counter top (not required).
NOTE: Units are supplied with the nipple PVC and pipe connected to condensing evaporator.
MODEL NUMBER
CUT-OUT SIZE
WCMBT-3
WCMBT-4
WCMBT-5
WCMBT-6
22 1/4 X 41 3/4
22 1/4 X 55 1/2
22 1/4 X 69 1/4
22 1/4 X 83
The unit should be level for draining purposes. When installing unit in a counter, it is recommended that the operator
side of the counter be completely open for air circulation. When this is not possible, such as in an island counter, it is
recommended that two grill openings are provided approximately 18” x 18” of free air for intake and exhaust at the
opposite ends of the counter.
The unit is supplied with a power cord and NEMA plug. Refer to the data plate on the compressor housing for the
amperage and voltage information. Use a licensed electrician when installing power source.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
OPERATION
The unit should be turned on one hour before serving and turned off after completing the serving period. If the
compressor does not start immediately there is a chance the unit is in a defrost mode. A timer is installed to shut down
the compressor for defrosting every 8 hour for 15 minutes. For maximum efficiency, empty food pans or covers must
be in the openings until unit is ready for product. Do not block discharge or intake openings inside the unit.
The thermostat has an off position and numbers from #1 through #7 (number 7 is the coldest). The unit should be
turned off every day after used. Note: The unit should not operate 24/7.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
NEVER CLEAN PANS WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER CLEANING
COULD SCAR, MARK AND/OR CORRODE PANS. DO NOT USE STEEL WOOL OR ABRASIVE PRODUCTS.
TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE ALL RESIDUES. FAILURE
TO MEET THESE CONDITIONS WILL VOID WARRANTY.
CLEAN CONDENSER COIL REGULARLY.
Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: [email protected]
PARTS LIST REFRIGERATED PAN WITH BLOWER & TIMER
WCMBT SERIES
1
10
8
2
3
4
5
W CM BT-5 SH O W N
DESCRIPTION
7
6
ITEM
NUMBER
PART
NUMBER
S80103-0
7002-0+Model
7020-0
1
2
3
4
5
6
Separator Channel
Vinyl Bead Gasket
Nylon Spacer
2060-1
1003-0
1069-1
Condensing Water Evaporator
Power Cord with Plug
Switch with Light
2029-17JP
2029-27JL
S11855-0
S81857-0
2014-5
1/4 H.P. Compressor WCMBT-3
1/3 H.P. Compressor WCMBT-4, 5, 6
Blower Housing Assembly WCMBT-3
Blower Housing Assembly WCMBT-4, 5, 6
Fan Blade (Not Shown)
7
8
9
10
11
12
13
S81443-0
2013-0
S11857-0
S81862-0
2119-3
Fan Guard
Fan Motor (Not Shown)
Drain Pan WCMBT-3 (Not Shown)
Drain Pan WCMBT-4, 5, 6 (Not Shown)
Evaporator Coil WCMBT-3 (Not Shown)
Evaporator Coil WCMBT-4, 5, 6 (Not Shown)
Defrost Thermostat (Not Shown)
Timer (Not shown)
Heating Element WCMBT-3 (Not Shown)
Heating Element WCMBT-4, 5, 6 (Not Shown)
0.042 Cap Tube (Not Shown)
Harness (Not Shown)
12
2119-1
13
14
22-1399
20-3010
111-1080
111-1071
2026-0
1150
2025-0
2044-0
15
16
17
18
19
Drier (Not Shown)
Thermostat (Not Shown)
REFRIGERATED PAN WITH EVAPORATOR
BLOWER & TIMER
WCMBT SERIES
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
INSTALLATION
Provide the correct counter cut-out opening (see chart below) and drop in. The vinyl gasket assures complete seating. A
non-toxic silicone seal may be used between the gasket and counter top (not required).
NOTE: Units are supplied with the nipple PVC and pipe connected to condensing evaporator.
MODEL NUMBER
CUT-OUT SIZE
WCMBT-3
WCMBT-4
WCMBT-5
WCMBT-6
22 1/4 X 41 3/4
22 1/4 X 55 1/2
22 1/4 X 69 1/4
22 1/4 X 83
The unit should be level for draining purposes. When installing unit in a counter, it is recommended that the operator
side of the counter be completely open for air circulation. When this is not possible, such as in an island counter, it is
recommended that two grill openings are provided approximately 18” x 18” of free air for intake and exhaust at the
opposite ends of the counter.
The unit is supplied with a power cord and NEMA plug. Refer to the data plate on the compressor housing for the
amperage and voltage information. Use a licensed electrician when installing power source.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
OPERATION
The unit should be turned on one hour before serving and turned off after completing the serving period. If the
compressor does not start immediately there is a chance the unit is in a defrost mode. A timer is installed to shut down
the compressor for defrosting every 8 hour for 15 minutes. For maximum efficiency, empty food pans or covers must
be in the openings until unit is ready for product. Do not block discharge or intake openings inside the unit.
The thermostat has an off position and numbers from #1 through #7 (number 7 is the coldest). The unit should be
turned off every day after used. Note: The unit should not operate 24/7.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
NEVER CLEAN PANS WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER CLEANING
COULD SCAR, MARK AND/OR CORRODE PANS. DO NOT USE STEEL WOOL OR ABRASIVE PRODUCTS.
TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE ALL RESIDUES. FAILURE
TO MEET THESE CONDITIONS WILL VOID WARRANTY.
CLEAN CONDENSER COIL REGULARLY.
Subsidiaꢀ of Meꢁuꢀ Aꢂꢃꢄ, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: sales@atlasfoodseꢀ.com
Reꢀigerated Drop-In Trouble Shooting Guide
Symptom
Probable Cause
Unit not plugged in.
No power at receptacle.
Unit will not run
Thermostat and or switch not in the on position.
Unit may be in a deꢀost cycle (ifsupplied) wait approximately 20 min.
Call ꢁctory ꢂr service at 1-800-762-7565
Condenser coil dirty
Inadequate ventilation.
Call ꢁctory ꢂr service at 1-800-762-7565
Condenser coil dirty.
Condenser runs but
short cycles
Inadequate ventilation.
Unit installed in a hot location
Condenser runs
constantly.
Call ꢁctory ꢂr service at 1-800-762-7565
NOTE: WF series runs constantly.
Food product must be chilled to 33-35 deg. when placed in unit.
Air movement over ꢂod proꢃct.
Food product not being stirred or rotated.
Call ꢁctory ꢂr service at 1-800-762-7565
Food product not
cold enough.
4
3
2
1
B
B
A
A
REVISION HISTORY
DESCRIPTION
DATE:
09.17.08
SIwE:
B
CrSTOMER:
REcERENCE:
ThHVH SOD V DrH thH H cO ViYH SroSHrt
REV
1
2
3
4
DATE
BY
tCMBT EiECTRICAi SCHEMATIC
tCMBT 3-4-5-6
oI AtODV MHtDO I d VtriHV I c. A
D thori Hd
DRAtN BY:
MHA
VH w itho t w rittH co VH t oI AtODV
MHtDO I d VtriHV I c., iV VtrictO SrohiEitHd.
CHEChED BY:
NS
P.O. #:
JOB #:
DRAtINd No.
-----
------
------
SCAiE: 3/4" = 1'-0"
SHEET No. 1 Oc 1
1135 Nt 159TH DRIVE MIAMI, ciORIDA 33169
5
4
3
2
1
LIMITED WARRANTY
Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the
same shall be free from defects in the workmanship and material for a period of
one year from the date of original installation of the equipment, but not to exceed
eighteen (18) months after date of shipment from factory. During this period of
time Atlas Metal Industries, Inc. will replace all defective parts and will pay for
authorized replacement labor. Replacement and installation of such parts and
labor shall be provided only upon prior written authority of Atlas Metal Industries,
Inc.
The Refrigeration warranty is for a twenty (20) month time period and includes
supplying the compressor at a no charge basis provided the damage to the
compressor was not caused by the customer or end user. Authorized
replacement labor will be paid for a period of one year from date of installation.
Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not
included, and all defective parts must be returned to the factory freight prepaid
for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS
METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE.
This warranty does not apply to any equipment or any part thereof, which has
been subjected to shipping damage, improper voltage, alteration, abuse or
misuses, and does not cover loss of food, other products, or damage to property
due to mechanical or electrical malfunction.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF
THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS
ARE SOLD “AS IS.”
WARRANTY INFORMATION
In order to have your invoice approved for
payment by the factory, please note the following:
_______________________________________________
An authorization number must be obtained from
the factory prior to performing any warranty
service.
_______________________________________________
Atlas Metal will not approve excessive labor due to poor
access to the unit being serviced. If design does not
allow reasonable access, contact the factory.
_______________________________________________
All travel time that exceeds 100 miles round trip
must be authorized by the factory.
_____________________________________________________________________________________
Thank You:
Warranty service Dept.
|