ACER ED242QR User Manual

Acer LCD M onitor  
Users Guide  
Special notes on LCD m onitors  
The following are normal with the LCD monitor and do not indicate a problem.  
Due to the nature of the fluorescent light, the screen may flicker during initial  
use. Turn off the power switch and then turn it on again to make sure the flicker  
disappears.  
You may find slightly uneven brightness on the screen depending on the desktop  
pattern you use.  
The LCD screen has 99.99% or more effective pixels. It may include blemishes of  
0.01% or less such as a missing pixel or a pixel lit all the time.  
Due to the nature of the LCD screen, an afterimage of the previous screen may  
remain after switching the image, when the same image is displayed for hours. In  
this case, the screen is recovered slowly by changing the image or turning off the  
power switch for a few hours.  
Inform ation for your safety and  
com fort  
Safety instructions  
Read these instructions carefully. Keep this document for future reference. Follow all  
warnings and instructions marked on the product.  
Cleaning your monitor  
Please carefully follow these guidelines when cleaning the monitor:  
Always unplug the monitor before cleaning.  
Use a soft cloth to wipe the screen and cabinet front and sides.  
Connecting/disconnecting the device  
Observe the following guidelines when connecting and disconnecting power from the  
LCD monitor:  
Make sure the monitor is attached to its base before connecting the power cord to  
the AC power outlet.  
Make sure both the LCD monitor and the computer are turned off before  
connecting any cable or unplugging the power cord.  
If the system has multiple sources of power, disconnect power from the system by  
unplugging all power cords from the power supplies.  
iii  
Accessibility  
Be sure that the power outlet you plug the power cord into is easily accessible and  
located as close to the equipment operator as possible. When you need to disconnect  
power from the equipment, be sure to unplug the power cord from the electrical outlet.  
Safe listening  
To protect your hearing, follow these instructions.  
Gradually increase the volume until you can hear it clearly and comfortably and  
without distortion.  
After setting the volume level, do not increase it after your ears have adjusted.  
Limit the amount of time listening to music at high volume.  
Avoid turning up the volume to block out noisy surroundings.  
Turn the volume down if you can’t hear people speaking near you.  
Warnings  
Do not use this product near water.  
Do not place this product on an unstable cart, stand or table. If the product falls, it  
could be seriously damaged.  
Slots and openings are provided for ventilation to ensure reliable operation of the  
product and to protect it from overheating. These openings must not be blocked  
or covered. The openings should never be blocked by placing the product on a bed,  
sofa, rug or other similar surface. This product should never be placed near or over  
a radiator or heat register, or in a built-in installation unless proper ventilation is  
provided.  
Never push objects of any kind into this product through cabinet slots as they may  
touch dangerous voltage points or short-out parts that could result in a fire or  
electric shock. Never spill liquid of any kind onto or into the product.  
To avoid damage of internal components and to prevent battery leakage, do not  
place the product on a vibrating surface.  
Never use it under sporting, exercising, or any vibrating environment which will  
probably cause unexpected short current or damage internal devices.  
Using electrical power  
This product should be operated from the type of power indicated on the marking  
label. If you are not sure of the type of power available, consult your dealer or local  
iv  
power company.  
Do not allow anything to rest on the power cord. Do not locate this product where  
people will walk on the cord.  
If an extension cord is used with this product, make sure that the total ampere  
rating of the equipment plugged into the extension cord does not exceed the  
extension cord ampere rating. Also, make sure that the total rating of all products  
plugged into the wall outlet does not exceed the fuse rating.  
Do not overload a power outlet, strip or receptacle by plugging in too many  
devices. The overall system load must not exceed 80% of the branch circuit rating.  
If power strips are used, the load should not exceed 80% of the power strips input  
rating.  
This products power cord is equipped with a three-wire grounded plug. The plug  
only fits in a grounded power outlet. Make sure the power outlet is properly  
grounded before inserting the power cord plug. Do not insert the plug into a non-  
grounded power outlet. Contact your electrician for details.  
Warning! The grounding pin is a safety feature. Using a pow er  
outlet that is not properly grounded m ay result in electric  
shock and/or injury.  
Note: The grounding pin also provides good protection from  
unexpected noise produced by other nearby electrical devices that  
may interfere with the performance of this product.  
Use the product only with the supplied power supply cord set. If you need to  
replace the power cord set, make sure that the new power cord meets the  
following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated  
7 A 125 V minimum, VDE approved or its equivalent, 4.5 meters (15 feet) maximum  
length.  
Product servicing  
Do not attempt to service this product yourself, as opening or removing covers may  
expose you to dangerous voltage points or other risks. Refer all servicing to qualified  
service personnel.  
Unplug this product from the wall outlet and refer servicing to qualified service  
v
personnel when:  
the power cord or plug is damaged, cut or frayed  
liquid was spilled into the product  
the product was exposed to rain or water  
the product has been dropped or the case has been damaged  
the product exhibits a distinct change in performance, indicating a need for service  
the product does not operate normally after following the operating instructions  
Note: Adjust only those controls that are covered by the operating  
instructions, since improper adjustment of other controls may result  
in damage and will often require extensive work by a qualified  
technician to restore the product to normal condition.  
Potentially explosive environments  
Switch off your device in any area with a potentially explosive atmosphere and obey all  
signs and instructions. Potentially explosive atmospheres include areas where you would  
normally be advised to turn off your vehicle engine. Sparks in such areas could cause  
an explosion or fire resulting in bodily injury or even death. Switch off the device near  
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel  
depots, storage and distribution areas; chemical plants; or where blasting operations are  
in progress. Areas with a potentially explosive atmosphere are often, but not always,  
marked. They include below deck on boats, chemical transfer or storage facilities,  
vehicles using liquefied petroleum gas (such as propane or butane), and areas where the  
air contains chemicals or particles such as grain, dust or metal powders.  
Additional safety information  
Your device and its enhancements may contain small parts. Keep them out of the reach  
of small children.  
IT Equipment Recycling Information  
Acer is strongly committed to environmental protection and views recycling, in the form  
of salvaging and disposal of used equipment, as one of the company’s top priorities in  
minimizing the burden placed on the environment.  
We at Acer are very conscious of the environmental effects of our business and strive to  
identify and provide the best working procedures to reduce the environmental impact  
of our products.  
For more information and help when recycling, please go to this website:  
vi  
other products.  
Disposal instructions  
Do not throw this electronic device into the trash when discarding. To minimize  
pollution and ensure utmost protection of the global environment, please recycle.  
For more information on the Waste from Electrical and Electronics Equipment (WEEE)  
LCD pixel statement  
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,  
some pixels may occasionally misfire or appear as black or red dots. This has no effect on  
the recorded image and does not constitute a malfunction.  
This product has been shipped enabled for power management:  
Activate display’s Sleep mode within 5 minutes of user inactivity.  
Wake the monitor when it is in Active Off mode, move the mouse or press any  
keyboard key.  
Tips and information for comfortable use  
Computer users may complain of eyestrain and headaches after prolonged use. Users are  
also at risk of physical injury after long hours of working in front of a computer. Long  
work periods, bad posture, poor work habits, stress, inadequate working conditions,  
personal health and other factors greatly increase the risk of physical injury.  
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis  
or other musculoskeletal disorders. The following symptoms may appear in the hands,  
wrists, arms, shoulders, neck or back:  
numbness, or a burning or tingling sensation  
aching, soreness or tenderness  
vii  
pain, swelling or throbbing  
stiffness or tightness  
coldness or weakness  
If you have these symptoms, or any other recurring or persistent discomfort and/or pain  
related to computer use, consult a physician immediately and inform your company’s  
health and safety department.  
The following section provides tips for more comfortable computer use.  
Finding your comfort zone  
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,  
or raising your sitting height to achieve maximum comfort. Observe the following tips:  
refrain from staying too long in one fixed posture  
avoid slouching forward and/or leaning backward  
stand up and walk around regularly to remove the strain on your leg muscles  
Taking care of your vision  
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room  
lighting, poorly focused screens, very small typefaces and low-contrast displays could  
stress your eyes. The following sections provide suggestions on how to reduce eyestrain.  
Eyes  
Rest your eyes frequently.  
Give your eyes regular breaks by looking away from the monitor and focusing on a  
distant point.  
Blink frequently to keep your eyes from drying out.  
Display  
Keep your display clean.  
Keep your head at a higher level than the top edge of the display so your eyes  
point downward when looking at the middle of the display.  
Adjust the display brightness and/or contrast to a comfortable level for enhanced  
text readability and graphics clarity.  
Eliminate glare and reflections by:  
placing your display in such a way that the side faces the window or any light  
source  
viii  
minimizing room light by using drapes, shades or blinds  
using a task light  
changing the display’s viewing angle  
using a glare-reduction filter  
using a display visor, such as a piece of cardboard extended from the display’s  
top front edge  
Avoid adjusting your display to an awkward viewing angle.  
Avoid looking at bright light sources, such as open windows, for extended periods  
of time.  
Developing good work habits  
Develop the following work habits to make your computer use more relaxing and  
productive:  
Take short breaks regularly and often.  
Perform some stretching exercises.  
Breathe fresh air as often as possible.  
Exercise regularly and maintain a healthy body.  
ix  
Declaration of Conformity  
We,  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan  
Contact Person: Mr. RU Jan, e-mail:[email protected]  
And,  
Acer Italy s.r.l  
Via Lepe t, 40, 20020 Lainate (MI) Italy  
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913  
Declare under our own responsibility that the product:  
Product:  
LCD Monitor Acer  
Trade Name:  
Model Number:  
SKU Number:  
ED242QR  
ED242QR  
xxxxxx;  
(“x” = 0~9, a ~ z, A ~ Z, or blank)  
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in  
conformity with the relevant Union harmonization legislations as below Directive and following harmonized  
standards and/or other relevant standards have been applied:  
EMC Directive: 2014/30/EU  
EN 55022:2010+AC:2011 Class B  
EN 55024:2010  
EN 61000-3-2:2006+A2:2009 Class D  
EN 61000-3-3:2013  
LVD Directive: 2014/35/EU  
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013  
RoHS Directive: 2011/65/EU  
EN 50581:2012  
ErP Directive: 2009/125/EC  
Regulation (EC) No. 1275/ 2008; EN 50564:2011  
Year to begin affixing CE marking: 2016.  
_______________________________  
RU Jan / Sr. Manager  
Acer Incorporated (Taipei, Taiwan)  
Jan.24, 2017  
Date  
Acer America Corporation  
333 West San Carlos St., San Jose  
Suite 1500  
CA 95110, U. S. A.  
Tel : 254-298-4000  
Fax : 254-298-4147  
Federal Communications Commission  
Declaration of Conformity  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
The following local Manufacturer /Importer is responsible for this declaration:  
Product:  
LCD Monitor  
ED242QR  
Model Number:  
SKU Number:  
ED242QR xxxxxx;  
xxxxxx (“x” = 0~9, a ~ z, or  
A ~ Z)  
Name of Responsible Party:  
Address of Responsible Party:  
Acer America Corporation  
333 West San Carlos St.  
Suite 1500 San Jose, CA  
95110 U. S. A.  
Contact Person:  
Phone No.:  
Fax No.:  
Acer Representative  
254-298-4000  
254-298-4147  
Special notes on LCD monitors  
iii  
Information for your safety and comfort  
Safety instructions  
iii  
iii  
Cleaning your monitor  
iii  
Connecting/disconnecting the device  
Accessibility  
Safe listening  
Warnings  
Using electrical power  
iii  
iv  
iv  
iv  
iv  
v
Product servicing  
Potentially explosive environments  
Additional safety information  
IT Equipment Recycling Information  
Disposal instructions  
LCD pixel statement  
Tips and information for comfortable use  
Declaration of Conformity  
vi  
vi  
vi  
vii  
vii  
vii  
Federal Communications Commission  
Declaration of Conformity  
Unpacking  
1
2
3
4
4
4
5
7
Attaching/ Removing the base  
Screen position adjustment  
Connecting the Power cord  
Power saving  
Display Data Channel (DDC)  
Connector pin assignment  
Standard timing table  
Installation  
8
9
Users controls  
Adjusting the OSD settings  
10  
12  
18  
The Function page  
Trouble shooting  
Unpacking  
Please check that the following items are present when you unpack the box, and save  
the packing materials in case you need to ship or transport the monitor in the future.  
LCD monitor  
Quick start guide  
Adapter  
VGA cable (Optional)  
HDM I cable (Optional)  
AC Power cord  
1
Attaching/ Removing the base  
Take out the monitor, stand and base from the package, put them on smooth surface.  
Align the stand for the back cover portion of the monitor, insert the back cover, ensure that the  
monitor and.standconnection is stable, do not shake.  
1.  
2.  
Align base and stand, insert the base to stand, rotating hand screw until tightening, fix the base.  
3.  
1. Attach the base to the monitor, as illustrated.  
2. Ensure that the base is screwed tight onto the monitor stand arm.  
2
Screen position adjustment  
To optimize the viewving position, you can adjust the monitor tilt by using  
both of your hands to hold the edges of the monitor as shown below. The  
monitor can be adjusted to 20 degrees up or 5 degrees down.  
3
Connecting the Pow er cord  
Check first to make sure that the power cord you use is the correct type required  
for your area.  
The monitor has a universal power supply that allows operation in either 100/120 V  
AC or 220/240 V AC voltage area. No user-adjustment is required.  
Plug one end of the power cord to the AC inlet, and plug the other end into an AC  
outlet.  
For units using 120 V AC:  
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.  
For units using 220/240 V AC:  
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord  
set should have the appropriate safety approvals for the country in which the  
equipment will be installed.  
Pow er saving  
The monitor will be switched to “power saving” mode by the control signal from the  
display controller, as indicated by the amber-colored power LED.  
M ode  
On  
LED light  
Blue  
Power saving  
Flicker  
The power saving mode will be kept until a control signal has been detected or the  
keyboard or mouse is activated. The recovery time from “power saving” mode back to  
“on” is around 3 seconds.  
Display Data Channel (DDC)  
To make installation easier, so long as your system supports the DDC protocol, the  
monitor is able to plug-and-play. The DDC is a communication protocol through which  
the monitor automatically informs the host system about its capabilities; for example,  
supported resolutions and corresponding timing. The monitor supports the DDC2B  
standard.  
4
Connector pin assignm ent  
1
6
5
10  
15  
11  
15-pin color display signal cable  
PIN No. Description  
PIN No. Description  
1
2
3
4
5
6
7
8
Red  
9
+5 V  
Green  
10  
11  
12  
13  
14  
15  
Logic ground  
M onitor ground  
DDC-serial data  
H-sync  
Blue  
M onitor ground  
DDC-return  
R-ground  
G-ground  
B-ground  
V-sync  
DDC-serial clock  
5
19-Pin Color Display Signal Cable*  
PIN  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
Meaning  
TMDS Data2+  
PIN  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
Meaning  
TMDS Clock+  
TMDS Clock Shield  
TMDS Clock-  
CEC  
TMDS Data2 Shield  
TMDS Data2-  
TMDS Data1+  
TMDS Data1 Shield  
TMDS Data1-  
Reserved (N.C. on device)  
SCL  
TMDS Data0+  
SDA  
TMDS Data0 Shield  
TMDS Data0-  
DDC/CEC Ground  
+5V Power  
Hot Plug Detect  
* only for certain models  
6
Standard tim ing table  
No.  
1
Mode  
VGA  
Resolution  
640x480  
Refresh Rate  
60  
72  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
2
640x480  
640x480  
3
MAC  
VESA  
66.7  
70  
56  
60  
72  
60  
70  
75  
60  
60  
60  
60  
60  
60  
60  
60  
60  
4
720x400  
5
800x600  
6
800x600  
SVGA  
7
800x600  
8
1024x768  
1024x768  
1152x864  
1280x960  
1280x1024  
1280x720  
1280x800  
1360x768  
1440x900  
1680x1050  
1600x1200  
1920x1080  
XGA  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
VESA  
SXGA  
VESA  
W XGA  
W XGA+  
W SXGA+  
UXGA  
VESA  
7
Installation  
To install the monitor on your host system, please follow the steps below:  
Steps  
1
Connect the video cable  
a
M ake sure both the monitor and computer are switched off.  
Connect the VGA video cable to the computer.  
b
c
Connect the digital cable (only for dual-input models).  
(1) M ake sure both the monitor and computer are switched off.  
(2) Connect one end of the 24-pin DVI cable to the back of the monitor and  
the other end to the computers port.  
(3) HDM I Cable (Optional, only HDM I-Input M odel)  
a. M ake sure both the monitor and computer are powered-ON  
b.Connect the HDMI cable to the computer.  
Connect the power cord  
.
.
2
Connect the power cord to the monitor, then to a properly grounded AC outlet.  
Turn on the monitor and computer  
3
4
Turn on the monitor first, then the computer. This sequence is very important.  
If the monitor does not function properly, please refer to the troubleshooting section  
to diagnose the problem.  
HDMI  
A d a p te r  
VGA  
In order to prevent damage to the monitor, do not lift the monitor by its base.  
8
Users controls  
Monitor power off status Press to switch power on. In the  
normal display, anytime to Press more than 5 seconds  
switch to turn off the power.  
Function key  
a.  
b.  
Blue indicates power on. Blue flicker indicates standby/power  
saving mode. No light display indicates Power off.  
Press to any directions switch key to display First Menu.  
Press again to enter next function in the First Menu.  
c.  
d.  
The single toggle button on the backside of the Display bezel  
operates like a joystick. To move the cursor, simply toggle  
the button in four directions. Press the button to select desires  
option. In Main Menu The Green indicates operable, Grey  
indicates inoperable.  
9
Adjusting the OSD settings  
Note: The following content is for general reference only. Actual  
product specifications may vary.  
The OSD (on-screen display) can be used for adjusting the settings of your LCD  
Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust  
the picture quality, OSD position and general settings. For advanced settings,  
please refer to following page:  
Main Page  
1. M enu OSD  
2. M ode  
3. Brightness  
4. Input selection  
Turn Mode on or off  
Open the Mode control and turn Mode on or off using the adjustment arrows  
(OFF/ON), and select which profile to use (Please see the OSD section for more  
information).  
10  
Adjusting the Brightness setting  
Open the Brightness control and select the brightness setting using the arrows.  
When you are done, use  
to go back one level.  
Selecting the Input  
Open the input control and select HDMI, DisplayPort, or DVI. When you are  
done, use to go back one level.  
11  
The Function page  
Open the Function page to select Picture, Color, Audio, Gaming, OSD or  
System functions, and adjust the settings which you want using the arrows.  
You can also view your monitor’s system information from this page. When  
you are done, use  
to go back one level.  
Adjusting the Picture  
1. Press the MENU key to bring up the OSD.  
Toggle the joystick to the up or down to select Picture from the  
OSD.Then toggle to the right to navigate to the element you wish to  
adjust and press the joystick to enter it.  
2.  
Toggle to the left or right to adjust the sliding scales.  
3.  
4. The Picture menu can be used to adjust the Brightness, Contrast, Black  
Boost, Blue Light, ACM, and Super Sharpness.  
5. Brightness: Adjust the brightness from 0 to 100.  
Note: Adjusts the balance between light and dark shades.  
6. Contrast: adjust the contrast from 0 to 100.  
Note: Sets the degree of difference between light and dark areas.  
7. Black Boost: This boosts the amplitude of the dark color levels of the  
display– blacks will be less black. The higher the level, the higher the  
boost.  
12  
8. Blue Light: filter out blue light by adjusting different Blue Light showing  
ratio - 80%, 70%, 60%, 50%.  
Note: Higher values allow more blue light through. For the best  
protection, select a lower value.  
9. ACM: Turn ACM on or off. The default is off.  
10. Super Sharpness technology can simulate high-resolution images by  
boosting the pixel density of the original source. It can make images  
sharper and clear.  
Adjusting the Color  
1. Press the MENU key to open the OSD.  
Toggle the joystick to the up or down to select Color from the OSD.  
Then toggle to the right to navigate to the element you wish to  
adjust and press the joystick to enter it.  
2.  
Toggle to the left or right to adjust the sliding scales.  
3.  
13  
4. Gamma mode allows you to adjust the luminance tone. The default value  
is 2.2 (standard value for Windows).  
5. Color temperature: Default is warm. You can choose Cool, Warm,  
Bluelight or User.  
6. sRGB mode is for getting better color matching representation with the  
peripheral device, such as DSCs or printers.  
7. 6-axis Hue: Adjust the red, green, blue, yellow, magenta and cyan hue.  
8. 6-axis Saturate: Adjust the red, green, blue, yellow, magenta and cyan  
saturation.  
Adjusting the Gaming  
1. Press the MENU key to open the OSD.  
Toggle the joystick to the up or down to select Gaming from the  
OSD.Then toggle to the right to navigate to the element you wish to  
adjust and press the joystick to enter it.  
2.  
Toggle to the left or right to adjust the sliding scales.  
3.  
OD: Select Off, Norm al, or Extrem e.default Norm al  
Norm al8m sExtrem e4m s OFFPanel OD  
4.  
5.  
Aim point: Show an Aim point on the screen for shooting gam es.  
14  
Adjusting the OSD  
1. Press the MENU key to open the OSD.  
Toggle the joystick to the up or down to select OSD from the  
OSD.Then toggle to the right to navigate to the elem ent you wish  
to adjust and press the joystick to enter it.  
2.  
Toggle to the left or right to adjust the sliding scales.  
3.  
4. Language: Set the OSD menu language.  
5. OSD Timeout: Adjust the delay before turning the off the OSD menu.  
6. Transparency: Select the transparency when using gaming mode. The  
transparency can be 0% (OFF), 20%, 40%, 60%, or 80%.  
7. Refresh rate num: Display the panel’s current refresh rate on the screen.  
15  
Adjusting the System  
1. The System menu can be used to select settings such as Input, Wide  
Mode, and Power LED.  
2. Press the MENU key to open the OSD.  
Toggle the joystick to the up or down to select System from the OSD.  
Then toggle to the right to navigate to the elem ent you wish to  
adjust and press the joystick to enter it.  
3.  
Toggle to the left or right to adjust the sliding scales.  
4.  
5. Input: Select the source from VGA or HDMI.  
6. Auto Source: Automatically searches for available input sources.  
W ide m ode: You can select which screen aspect you are using. The  
options are Full, Aspect.  
7.  
Hotkey Assigm ent Select the function of shortcut key 1(M odes,  
Brightness, Input,  
8.  
Gam m a, Contrast, Blue Light, Over Drive) and shortcut keys 2  
(M odes, Brightness,  
Input, Gam m a, Contrast, Blue Light, Over Drive)  
9. DDC/CI: Allows the monitor settings to be set through the software on  
the PC.  
Note: DDC/CI, short for Display Data Channel/Command Interface,  
which allows monitor controls to be sent via software.  
10. HDMI Black Level: You can select the level of blackness under HDMI  
source. The options are Normal and Low.  
11. Quick Start Mode: Enable monitor rapidly.  
16  
Product information  
Save Setting to… (User m ode only)  
1. Press the MENU key to open the OSD.  
Toggle the joystick to the up or down to select "Save Setting to… " from  
2.  
the OSD. Then toggle to the right to navigate to the elem ent you wish  
to adjust and press the joystick to enter it.  
3. Reset: Resets all settings to the factory defaults.  
4. Save Setting to Gam e m ode: There are three user-defined profiles  
available. W hen you have decided what settings suit you, save them and  
system will be able to recall the settings in the future when you turn on  
gam ing m ode .  
17  
TROUBLESHOOTING  
Before sending your LCD monitor for servicing, please check the trouble-  
shooting list below to see if you can self-diagnose the problem.  
(HDMI/DP/DVI Mode)  
Problems  
Current Status  
Remedy  
Using OSD, adjust brightness  
LED ON  
and contrast to maximum or  
reset to their default settings.  
Check the power switch.  
Check if AC power cord is  
properly connected to the  
monitor.  
LED OFF  
No Picture  
Check if video signal cable is  
properly connected at the back  
of monitor.  
Check if the power of computer  
system is ON.  
LED Flicker  
18  

Whirlpool Acw082 User Manual
Studer Innotec C1312 Compact User Manual
Samsung Uq07s8ge User Manual
Samsung Aw0603b User Manual
Samsung Avmkc035ea User Manual
MIELE DA 5190 W User Manual
MAYTAG LSE7800ACE User Manual
LG 65UH5500 02 User Manual
DELL VENUE 8 PRO 5855 User Manual
CRAFTSMAN 139.53627SRT User Manual