|
Acer LCD Monitor
User Guide
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn
off the power switch and then turn it on again to make sure the flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the desktop pattern
you use.
The LCD screen has 99.99% or more effective pixels. It may include blemishes of 0.01%
or less such as a missing pixel or pixel lit all the time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screen is recovered slowly by changing the image or turning off the power switch for a
few hours.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
•
Always unplug the monitor before cleaning.
Use a soft cloth to wipe the screen and cabinet front and sides.
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located
as close to the equipment operator as possible. When you need to disconnect power from
the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably and without
distortion.
•
•
•
•
After setting the volume level, do not increase it after your ears have adjusted.
Limit the amount of time listening to music at high volume.
Avoid turning up the volume to block out noisy surroundings.
Turn the volume down if you can’t hear people speaking near you.
Warnings
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it could
be seriously damaged.
•
•
Slots and openings are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should never be placed near or over a radiator
or heat register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind onto or into the product.
•
•
•
To avoid dmage of internal components and to prevent battery leakage, do not place the
product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment which will probably
cause unexpected short current or damage internal devices.
The adapter is only used for this monitor, do not be used for other purposes.
Using electrical power
•
This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
•
Do not allow anything to rest on the power cord. Do not locate this product where people
will walk on the cord.
•
If an extension cord is used with this product, make sure that the total ampere rating
of the equipment plugged into the extension cord does not exceed the extension cord
ampere rating. Also, make sure that the total rating of all products plugged into the wall
outlet does not exceed the fuse rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too many devices. The
overall system load must not exceed 80% of the branch circuit rating. If power strips are
used, the load should not exceed 80% of the power strip’s input rating.
This product’s power cord is equipped with a three-wire grounded plug. The plug only
fits in a grounded power outlet. Make sure the power outlet is properly grounded before
inserting the power cord plug. Do not insert the plug into a non-grounded power outlet.
Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet
that is not properly grounded may result in electric shock and/or
injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to replace the
power cord set, make sure that the new power cord meets the following requirements:
detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V minimum, VDE
approved or its equivalent, 4.6 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose
you to dangerous voltage points or other risks. Refer all servicing to qualified service
personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel
when:
•
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need for service
the product does not operate normally after following the operating instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all signs
and instructions. Potentially explosive atmospheres include areas where you would normally
be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion
or fire resulting in bodily injury or even death. Switch off the device near depots, storage and
distribution areas; chemical plants; or where blasting operations are in progress. Areas with
a potentially explosive atmosphere are often, but not always, marked. They include below
deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas
(such as propane or butane), and areas where the air contains chemicals or particles such
as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach of
small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal of used equipment, as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to
identify and provide the best working procedures to reduce the environmental impact of our
products.
For more information and help when recycling, please go to this website:
products.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please recycle.
For more information on the Waste from Electrical and Electronics Equipment
(WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/
sustainability01.htm
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.
This product has been shipped enabled for power management:
•
•
Activate display’s Sleep mode within 5 minutes of user inactivity.
Wake the monitor when it is in Active Off mode,move the mouse or press any keyboard
key.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long work
periods, bad posture, poor work habits, stress, inadequate working conditions, personal
health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis or
other musculoskeletal disorders. The following symptoms may appear in the hands, wrists,
arms, shoulders, neck or back:
•
•
•
•
•
numbness, or a burning or tingling sensation
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s health
and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or
raising your sitting height to achieve maximum comfort. Observe the following tips:
•
•
•
refrain from staying too long in one fixed posture
avoid slouching forward and/or leaning backward
stand up and walk around regularly to remove the strain on your leg muscles
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room
lighting, poorly focused screens, very small typefaces and low-contrast displays could stress
your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and focusing on a
istant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
•
Keep your display clean.
Keep your head at a higher level than the top edge of the display so your eyes point
downward when looking at the middle of the display.
•
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced text
readability and graphics clarity.
Eliminate glare and reflections by:
•
•
•
•
•
•
placing your display in such a way that the side faces the window or any light source
minimizing room light by using drapes, shades or blinds
using a task light
changing the display’s viewing angle
using a glare-reduction filter
using a display visor, such as a piece of cardboard extended from the display’s top
front edge
•
•
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended periods of
time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and productive:
•
•
•
Take short breaks regularly and often.
Perform some stretching exercises.
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
And,
Acer Italy s.r.l.
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
Product:
LCD Monitor
Trade Name:
Model Number:
SKU Number:
Acer
B277K
B277K
(“x” = 0~9, a ~ z, A ~ Z, or blank)
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in
conformity with the relevant Union harmonization legislations as below Directive and following harmonized
standards and/or other relevant standards have been applied:
EMC Directive: 2014/30/EU
EN 55032:2012/AC:2013 Class B
EN 61000-3-2:2014 Class D
EN 55024:2010
EN 61000-3-3:2013
LVD Directive: 2014/35/EU
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013
RoHS Directive: 2011/65/EU
EN 50581:2012
ErP Directive: 2009/125/EC
Regulation (EC) No. 1275/ 2008; EN 50564:2011
Year to begin affixing CE marking: 2017.
Nov.10,2017
Date
_______________________________
RU Jan / Sr. Manager
Acer Incorporated (Taipei, Taiwan)
Acer America Corporation
333 West San Carlos St., San Jose
Suite 1500
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
B277K
Model Number:
B277K xxxxxx
(“x” = 0~9, a ~ z, or A ~ Z)
SKU Number:
Name of Responsible Party:
Acer America Corporation
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Address of Responsible
Party:
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
Information for your safety and comfort
Safety instructions
iii
iii
Special notes on LCD monitors
Cleaning your monitors
iii
iii
Accessibility
iv
Safe listening
iv
Warnings
iv
Using electrical power
iv
Product servicing
v
Potentially explosive environments
Additional safety information
IT Equipment Recycling Information
Disposal instructions
vi
vi
vi
vi
LCD pixel statement
vii
vii
vii
viii
viii
ix
Tips and information for comfortable use
Finding your comfort zone
Taking care of your vision
Developing good work habits
Declaration of Conformity
Federal Communications Commission
Declaration of Conformity
x
Unpacking
1
2
3
3
Attaching the base (for selected models)
Screen position adjustment
Connecting the adapter and AC Power cord
Power saving
Display Data Channel (DDC)
Connector pin assignment
19-pin color display signal cable
20-pin color display signal cable
20-pin color Mini-DP cable*
4
4
5
5
Standard timing table
Installation
6
7
Users controls
Panel controls
8
8
Using the Shortcut Menu
The Function page
9
10
Troubleshooting
15
15
Mini DP/HDMI/DP Mode (Optional)
Unpacking
Please check that the following items are present when you unpack the box, and save the
packing materials in case you need to ship or transport the monitor in the future.
USB cable
(Optional)
LCD monitor
Quick start guide
LCD Monitor B7 series-B277K
USER GUIDE
DP Cable
(Optional)
HDMI cable
(Optional)
AC Power cord
Audio Cable
Mini DP Cable
(Optional)
(Optional)
SCREEN POSITION ADJUSTMENT
In oder to optimize the best viewing position, you can adjust the height/tilt of the monitor.
•
Height Adjustment
After pressing the top of the monitor then you can adjust the height of the monitor.
1
2
120mm
•
Tilt
Please see the illustration below for an example of the tilt range.
Only at the highest point can 25 degrees of recline be offered for the angle of elevation.
•
Swivel
With the built-in pedestal, you can swivel the monitor for the most comfortable viewing
angle.
45°
45°
•
Monitor Pivot
Before rotating the display,lift it to the top position and then push it back to the utmost
degree. Rotate clockwise or counter-clockwise until the monitor stops at 90°.
±
90o
90o
Connecting the adapter and AC Power cord
•
•
•
•
•
Check first to make sure that the power cord you use is the correct type required for
your area.
The monitor has a universal power supply that allows operation in either 100/120 V AC
or 220/240 V AC voltage area. No user-adjustment is required.
Plug one end of the AC power cord to the Adapter, and plug the other end into an AC
outlet.
For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set
should have the appropriate safety approvals for the country in which the equipment will
be installed.
Power saving
The monitor will be driven into "Power Saving" mode by the control signal from the display
controller, as indicated by the amber-color power LED.
State
ON
LED Light
Blue
Power Saving Mode
Amber
The power saving states will be kept until a control signal has been detected or the keyboard
or mouse is activated. The recovery time from Active OFF state back to ON state is around
3 seconds.
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the monitor
is able to plug-and-play. The DDC is a communication protocol through which the monitor
automatically informs the host system about its capabilities; for example, supported
resolutions and corresponding timing. The monitor supports the DDC2B standard.
20-pin color display signal cable
PIN No. Description
PIN No. Description
1
3
ML_Lane 0+
ML_Lane 0-
GND
2
4
GND
ML_Lane 1+
ML_Lane 1-
GND
5
6
7
ML_Lane 2+
ML_Lane 2-
GND
8
9
10
12
14
16
18
20
ML_Lane 3+
ML_Lane 3-
CONFIG2
GND
11
13
15
17
19
KONFIG1
AUX CH+
AUX CH-
Return
Hot Plug
DP_PWR
19-pin color display signal cable
PIN No. Description
PIN No. Description
1
3
TMDS Data2+
TMDS Data2-
TMDS Data1 Shield
TMDS Data0+
TMDS Data0-
TMDS Clock Shield
CEC
2
4
TMDS Data2 Shield
TMDS Data1+
TMDS Data1-
5
6
7
8
TMDS Data0 Shield
TMDS Clock+
TMDS Clock-
9
10
12
14
16
18
11
13
15
17
19
Reserved (N.C. on device)
SDA
SCL
DDC/CEC Ground
Hot Plug Detect
+5V Power
20-pin color Mini-DP cable*
PIN No. Description
PIN No. Description
1
3
ML_Lane 0+
ML_Lane 0-
GND
2
4
GND
ML_Lane 1+
ML_Lane 1-
GND
5
6
7
ML_Lane 2+
ML_Lane 2-
GND
8
9
10
12
14
16
18
20
ML_Lane 3+
ML_Lane 3-
CONFIG2
GND
11
13
15
17
19
KONFIG1
AUX CH+
AUX CH-
Return
Hot Plug
DP_PWR
Standard timing table
VESA MODE
Resolution
MODE
1
2
3
4
5
6
7
8
VGA
MAC
VESA
SVGA
SVGA
XGA
640x480
60Hz
66.66Hz
70Hz
56Hz
60Hz
60Hz
70Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
75Hz
60Hz
30Hz
60Hz
640x480
720x400
800x600
800x600
1024x768
1024x768
1152x864
1280x1024
1280x720
1280x800
1440x900
1680x1050
1920x1080
2560x1440
2560x1440
3840x2160
3840x2160
XGA
VESA
SXGA
VESA
WXGA
WXGA+
WSXGA+
UXGA
QHD
9
10
11
12
13
14
15
16
17
18
QHD
UHD
UHD
Installation
1.
2.
Turn off your computer and unplug your computer's power cord.
Connect the signal cable to the Mini DP and /or HDMI (optional) and /or DP (optional) input socket of the monitor,
and the Mini DP and /or HDMI (optional) and /or DP (optional) output socket of the graphics card on the computer.
Then tighten the thumbscrews on the signal cable connector.
3.
4.
Connect the USB Cable(Optional)
Connect the USB 3.0 cable to port for fast charge.
Connect the USB 3.0 cable to port.
Optional: Connect the audio input socket (AUDIO IN) of the LCD monitor and the line-out port on the computer with
the audio cable.
5.
6.
Insert the monitor power cable into the power port at the back of the monitor.
Connect the power adapter and power cord to the monitor, then to a properly grounded AC outlet.
USB
USB
Note: Audio output is only for audio output model. Please check user manual for more instruction.
User Controls
1
2
3
4
5
External controls
1
Power button
Turns the monitor on/off.Blue indicates power on. Amber indicates
standby/ power saving mode.
2
Function key
/
a. Press to view Main page. Press again to enter hotkey1 function.
b. When the Function Menu is active, press this key to view the basic
information for your monitor and current input or reset the custom
color settings to the factory defaults.
3
4
5
Function key
/
a. Press to view Main page.Press again to enter hotkey2 function.
b. When the Function Menu is active, press this button to select
select scenario mode or game mode .
Function key
/
a. Press to view Main page.Press again to enter Input select
function.
b. When the Function Menu is active, this button will quit the OSD.
Function key
/
a. Press to view
.Press again to enter next function in
Main page
the Function Menu.
b. The single toggle button on the backside of the Display bezel
operates like a joystick. To move the cursor, simply toggle the
button in four directions. Press the button to select desired option.
Bright gray indicates operable. Dark gray indicates inoperable.
VESA Adaptive SYNC (HDMI/DP):
It can allow a VESA Adaptive SYNC supported graphics source to dynamically adjust display refresh
rate based on typical content frame rates for power efficient, virtually stutter free and low-latency display
update.
Using the Shortcut Menu
-------------------------------------------------------------------------------------------------------------
Note: The following content is for general reference only. Actual product specifications
may vary.
The OSD (onscreen display) can be used to adjust the settings of your LCD monitor. Press
the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD
position and general settings. For advanced settings, please refer to following page:
Main page
1.
2.
Hot Key1
Modes, Brightness, Volume, Gamma,
Contrast, Blue Light, Over Drive
Mode
Standard
Hot Key2
Modes, Brightness, Contrast, Volume,
Gamma, Blue Light, Over Drive
Brightness
65
Input
HDMI1
3.
4.
Hot Key3
Input Switch Hot Key
Main Menu
Menu
Hot key1 (default: Standard mode)
To choose scenario mode(sRGB,Reading,Darkroom,User, Standard, ECO, Graphics,
Movie)
Modes
sRGB
Darkroom
Graphics
Reading
User
Standard
ECO
Movie
Move
OK
Hot key2 (default: Brightness)
Open the Brightness control and select your preferred brightness setting . When you are
done, press the joystick to quit current page and store.
Brightness
80
Adjust
OK
Selecting the input
Open the Input control and select HDMI1, HDMI2, Mini DP ,DP or Auto Source. When you
are done, press the joystick to exit current page and store.
Input
Input
HDMI
On
Auto Source
Move
OK
Exit
Main menu
1. Press the MENU key to open the OSD.
to the up
or down
2. Toggle the joystick
to select Picture from the OSD. The
toggle to the right to navigate to the element you wish to adjust and press the joystick
to enter it.
to the left
3. Toggle the joystick
Information Hot Key
Modes Hot Key
or right to adjust the sliding scales.
: Show Monitor Information and Reset control function.
: To change Modes Hot Key menu.
Exit Hot Key
: To exit current page and store.
Picture
Mode - Standard
Picture
Color
Brightness
65
50
Contrast
Black Boost
Blue Light
5
Audio
Off
Performance
OSD
Off
ACM
HDR
Off
System
X
Super Sharpness
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select Picture from the OSD.Then toggle to the
right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to adjust the sliding scales.
4. The Picture menu can be used to adjust the Brightness, Contrast, Black Boost, Blue
Light, ACM,Super Sharpness.
5. Brightness: Adjust the brightness from 0 to 100.
-----------------------------------------------------------------------------------------------------------
Note: Adjusts the balance between light and dark shades.
6. Contrast: Adjust the contrast from 0 to 100.
-----------------------------------------------------------------------------------------------------------
Note: Sets the degree of difference between light and dark areas.
7. Black Boost: Adjust the black level from 0 to 10. Enhances shadows by increasing the
brightness without changing lighter shades.
8. Blue Light: Filters out blue light to protect your eyes by adjusting how much blue light is
shown -- 80%, 70%, 60%, or 50%.
-----------------------------------------------------------------------------------------------------------
Note: A higher value allows more blue light to pass through, so in order to
achieve the best protection, please select a lower value, of which 50% is in the
best state and has been tested by TÜV Rheinland and meet the requirements of TÜV
Rheinland's “Low Blue Light Content” standard.
9. ACM: Turn ACM on or off.
-----------------------------------------------------------------------------------------------------------
Set to "On", will be based on the current screen to dynamic contrast adjustment.
Note:
10. HDR: can control off and auto, the default is off, set to auto will automatically detect
and deal with HDR signal.
--------------------------------------------------------------------------------------------------------
Note: 1. When HDR = Auto, the Modes will also be automatically set to “HDR”.
2. When HDR = Auto, some parameters :(ACM, Gamma, Contrast, Blue Light,
Black Boost…) functions is gray out and disable, and if you change other adjustable
parameters, the “Modes” will not jump to “User” Mode.
11. Super Sharpness: Turn the Super Sharpness On or Off. Super Sharpness technology
can simulate high-resolution images by boosting the pixel density of the original source
to make images sharper and clearer..
Color
Mode - Stamdard
Picture
Color
Gamma
Color Temp.
R Gain
2.2
Warm
Audio
50
50
50
Performance
G Gain
OSD
B Gain
System
X
R Bias
50
50
G Bias
B Bias
50
Move
Enter
Mode - Stamdard
Picture
Color
Modes
Color Space
Standard
Audio
Grayscale Mode
6-axis Hue
Off
Performance
OSD
6-axis Saturate
System
X
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select Color from the OSD.Then toggle to the
right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to adjust the sliding scales.
4. Gamma mode allows you to adjust the luminance tone.The default value is 2.2 (standard
value for Windows).
5. Color temperature: Default is warm. You can choose Cool, Normal, Warm, Bluelight or
User.
6. Modes:To choose scenario mode.
7. Color Space: You can choose sRGB, EBU, DCI SMPTE-C and Standard.
,
8. Grayscale Mode:To choose Grayscale mode.
9. 6-axis Hue: Adjust the red, green, blue, yellow, magenta and cyan hue.
10. 6-axis Saturate: Adjust the red, green, blue, yellow, magenta and cyan saturation.
Audio
Mode - Stardard
Picture
Color
Volume
Mute
70
Off
Audio
Performance
OSD
X
System
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select Audio from the OSD.Then toggle to the
right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to adjust the sliding scales.
4. Volume: Adjust the volume
5. Mute:To choose mute on/off .
Performance
Mode - Standard
Picture
Normal
Over Drive
Color
Adapꢀve Sync
Off
Off
Audio
Refresh Rate Num
Performance
OSD
System
X
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select Gaming from the OSD.Then toggle to
the right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to control functions.
4. Over Drive: Select Off, Normal or Extreme.
5. Adaptive Sync:To choose Adaptive Sync on/off.
6. Refresh rate num: Display the panel’s current refresh rate on the screen.
-----------------------------------------------------------------------------------------------------------
Note: If Adaptive Sync set "On" you can see the V Frequency to changes in the
OSD.
OSD
Mode - Standard
Picture
Language
English
Color
OSD Timeout
10
Audio
Transparency
OSD Lock
Off
Off
Performance
OSD
System
X
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select OSD from the OSD.Then toggle to the
right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to adjust the sliding scales.
4. Language: Set the OSD menu language.
5. OSD timeout: Adjust the delay before turning off the OSD menu.
6. Transparency: Select the transparency when using gaming mode. The transparency
can be 0% (OFF), 20%, 40%, 60%, or 80%.
7. OSD Lock: To choose OSD lock on/off.
---------------------------------------------------------------------------------------------------------
Note:
OSD Locked:
•
Set the OSD Lock to "On" by the OSD option and press "Enter" to
execute the All Key lock function.
•
The "OSD Locked" message will be displayed in the middle of the
screen.
•
•
LED lights will be changed from blue light to orange light.
Press any Key screen to prompt "OSD Locked" message.
OSD Unlocked:
•
•
•
In normal display condition to press the "Navi Key" in the middle of
more than 3 seconds to trigger "OSD Unlock".
The "OSD Unlock" message will be displayed in the middle of the
screen.
LED lights will be restored to blue light.
System
Mode - Standard
Picture
Color
HDMI1
On
Input
Auto Source
DP Format
DP1.2
Full
Audio
Performance
OSD
Wide Mode
PIP/PBP
Hot Key Assignment
X
System
DDC/CI
On
HDMI Black Level
Normal
Move
Enter
Quick Start Mode
Mode - Standard
Picture
Color
Off
Off
Quick Start Mode
Power-off
USB charge
Audio
Performance
OSD
X
System
Move
Enter
Quick Start Mode
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select System from the OSD.Then toggle to the
right to navigate to the element you wish to adjust and press the joystick to enter it.
3. Toggle to the left or right to control functions.
4. Input: Select the source from HDMI1, HDMI2, Mini DP, DP.
5. Auto Source: The default is “On”, which can support auto search for signal source in
order.
-----------------------------------------------------------------------------------------------------------
Note: Surround application must set Auto Source is “Off”.
6. DP Format: Default is DP1.2, can selection support DP1.1 or DP1.2 format.
7. Wide mode: You can select which screen aspect you are using. The options are Aspect
and Full.
8. PIP/PBP: Select to set PIP/PBP.
9. Hot Key Assigment: Select the function of shortcut key 1(Modes, Volume, Brightness,
Gamma, Contrast, Blue Light, Over Drive) and shortcut keys 2 (Modes, Volume,
Brightness, Gamma, Contrast, Blue Light, Over Drive).
10. DDC/CI: Allows the monitor settings to be set through the software on the PC.
-----------------------------------------------------------------------------------------------------------
Note: DDC/CI, short for Display Data Channel/Command Interface, which allows
monitor controls to be sent via software.
11. HDMI Black level: Select to set HDMI black level.
12. Quick start mode: Select Off or On. Turn on to speed up boot speed.
13. Power-off USB Charge: Turn On or Off.
Save Setting to…(User mode only)
Mode - User
Picture
Color
Mode: Standard
Mode: ECO
Audio
Mode: Graphic
Mode: Movie
Mode: User
Performance
OSD
System
X
Save seꢀng to...
Move
Enter
1. Press the MENU key to open the OSD.
2. Toggle the joystick to the up or down to select "Save Setting to..." from the OSD.Then
toggle to the right to navigate to the element you wish to adjust and press the joystick
to enter it.
3. Save Setting to Game mode: There are five user-defined profiles available. When you
have decided what settings suit you, save them and system will be able to recall the
settings in the future when you turn on gaming mode .
Troubleshooting
Before sending your LCD monitor for servicing, please check the troubleshooting list below
to see if you can self-diagnose the problem.
Mini DP/HDMI/DP Mode (Optional)
Problem
LED status
Blue
Remedy
No picture visible
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
setting.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Amber
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
If OSD Lock is On, the LED status set Amber.
Note: Acer monitor is purposed for video and visual display of information obtained from
electronic devices.
|