Electric Fireplace Instruction Manual
Built-in Fireplaces DF-EFP1313-BLT
Yosemite Home Décor
1-800-305-9872
Table of Content
Important Safety Instructions
Packing List
Page 4
Page 5
Installation Instructions
Wall Installation
Page 6
Page 7
Page 9
Page 10
Page 10
Page 11
Page 13
Page 14
Built-in Installation
Coals and Crystal Installation
Electrical Works Instructions
Grounding Instructions
Operating Instruction
Troubleshooting Guide
Yosemite Warranty
3 | P a g e
IMPORTANT SAFETY INSTRUCTIONS_________________________________________
When using electric fireplaces, basic precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces, such as
surfaces near the heater outlet or light bulbs. Keep combustible materials such as clothes,
pillows, furniture, bedding, papers and curtains at least 3 feet from the front of this appliance.
3. CAUTION: Whenever the heater is left operating and unattended, extreme caution is necessary
if children or invalids are nearby.
4. Do not install the fireplace directly on carpet or a similar surface, which may restrict air
circulation beneath the unit.
5. Always unplug fireplace when not in use. Disconnect the heater by turning controls to off then
remove plug from outlet before performing any cleaning, maintenance or relocation of the
fireplace.
6. Fireplace is designed for indoor and household use only.
7. This fireplace is not intended for use in wet locations such as bathrooms, laundry areas and
similar indoor locations. Never locate fireplace where it may fall into a bathtub or other water
container.
8. If the fireplace shows any signs of damage or if the heater has malfunctioned. Return fireplace to
authorized service for examination, adjustment or repair.
9. Do not run cord under carpeting or route cord under furniture or appliance. Do not cover cord
with throw rugs and runners. Arrange cord away from traffic areas and where it will not be
tripped over.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may
cause an electric shock, fire, or may damage the heater.
11. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to
flammable vapours.
12. Always use properly grounded, fused and polarized outlets. Always use ground fault protection
where required by electrical code.
13. Extension cord may become overheat and may cause a risk of fire. If you have to use an extension
cord, the cord shall be 16AWG minimum size and rate not less than 125V/15A or 2500 watts.
14. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.
15. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an external switching device such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.
4 | P a g e
PACKING LIST______________________________________________________________________
Parts list
Quantity
A. Fireplace/Firebox …..………………………………………………………………………………………………………… 1
B. Mounting Plate ………………………………………………………………………………………………………………... 1
C. Glass Front…………………………………………………………………….…………………………………………………… 1
D. Remote Control ………………………………………………………………………………………………………………… 1
E. Instruction Manual ……….…………………………………………………………………………………………………. 1
B
C
D
E
5 | P a g e
INSTALLATION INSTRUCTIONS________________________________________________
A. Wall Installation
Due to the many different finish materials used on walls, it is highly recommended that you
consult your local builder before you install this fireplace on the wall.
1. The fireplace may be hanged on any wall surface that can support its weight and where it
can be leveled. It is important that the wall on to which the fireplace is to be installed is
of sound construction.
2. The fireplace must be kept away from any source of damp or moist conditions. Avoid any
close contact with water. And a minimum of 3 feet away from any combustible material
is a must.
3. Select the position of the fireplace on the wall to which it is to be mounted. There are
keyholes located at the back of the fireplace. Drill a hole according to the position of the
keyholes.
4. Use strong screws to mount it onto the wall. Each of the screws needs to come 8mm out
of the wall. Ensure that the screws are solidly mounted.
5. Have two or more people hold the fireplace. Lift the fireplace
and place the keyhole slots situated on the back of the fire. A
gentle application of downward pressure will lock it into place.
Make sure all of the pins have been located into the top section
of each keyhole fixing slot. See figure 1 & 2
Fig. 1
Fig. 2
6 | P a g e
B. Built-in Installation
Due to the many different finish materials used on walls, it is highly recommended that you
consult your local builder before you install this fireplace on the wall.
1. Select a suitable location for your fireplace.
2. Prepare a frame opening according to the dimension of the firebox. Put an allowance of
½ inches to its width and height dimensions. Kindly refer to the chart below.
FRAME OPENING
DIMENSION with 1/2”
FIREBOX DIMENSION
MODEL#
ALLOWANCE
Width
82.21”
Height
Depth
7.75”
Width
82.71”
Height
Depth
DF-EFP1313-BLT
21.34”
21.84”
5.00”
3. Lift fireplace and insert into opening. Adjust the unit to achieve the desired amount of
depth.
7 | P a g e
4. Level the fireplace.
5. Drive mounting screws into mounting brackets on the unit and the wall studs.
Side View
Wall Installation
Built-in Installation
8 | P a g e
C. Coals and Crystal Installation
Once fireplace is shipped, a standard coal is already attached to the unit.
To change from Coals to Crystal
1. Unplug unit from the wall and ensure controls are switched off.
2. Remove the glass face from the firebox unit and place the glass in a safe location.
3. There is an angle iron bar that is located at both side of the fireplace. Unscrew the
angle iron bar before lifting the coal out from the fireplace. See figure 3
Fig. 3
4. Place the crystals by spreading into the glass media tray provided.
5. Once done, re-attach the glass face to the firebox
To change from Crystal to Coal
1. Unplug unit from the wall and ensure controls are switched off.
2. Remove the glass face from the firebox unit and place the glass in a safe location.
3. Remove the crystal out from the fireplace.
4. Place the coal into the glass media tray provided and fix two (2) angle iron bar at
both sides of the fireplace.
5. Once done, re-attached the glass face to the firebox.
9 | P a g e
ELECTRICAL WORKS INSTRUCTIONS_________________________________________
This fireplace must be grounded
1. A standard electrical outlet must be closed to the fireplace. If the electric outlet is
required to be concealed, it can be located above or on the right hand side of the fire.
2. DO NOT INSTALL THE FIREPLACE WHERE THE HEATER IS DIRECTLY
ABOVE AN OUTLET. The heater is located in the center of the fireplace base.
3. If the power supply cable becomes damaged in any manner it MUST be replaced.
4. Always ensure that all electrical work complies with the relevant Building Codes. All
electrical work should be carried out by a qualified electrician.
5. The fireplace must not be modified in any way or used for purpose other than those
recommended by Yosemite Home Decor.
6. Please observe these instructions as failure to do so may result in electric shock or other
injury.
GROUNDING INSTRUCTIONS___________________________________________________
This fireplace is for use on 120 volts. The cord has a plug as shown in (A) at Figure 7. An
adapter as shown in (C) is available for connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding lug
extending from the adapter must be
connected to a permanent ground
such as a properly grounded outlet
box. The adapter should not be used
if a three-slot grounded receptacle is
available.
Fig. 7
10 | P a g e
OPERATING INSTRUCTIONS____________________________________________________
This section will explain the function of each convenient control.
A. Operation by Control Panel
The control panel is located on the right hand side of the fireplace. (Figure 8)
A
B
Main Power Switch
On/Off Switch
C
D
E
Flame Effect Dimmer Switch
Heater Low Heat 675 W
Heater Maximum Heat 1350 W
There are four indicators in the control panel. See Figure 8
this is the power indicator, it lights up when the fireplace insert is working, and turned out
when the fireplace is turned off;
indicate s the status of the simulated flame and logs.
indicates the heater is working in low-power status;
indicates the heater is working in high-power status.
11 | P a g e
B. Operation by Remote Control
1. Prior to use, the handheld remote control requires installation of one (1) coin-cell
battery.
2. Remove the cover on the rear of the remote control by sliding backwards. Install the
batteries as shown and then slide the cover back into original position.
3. To enable the remote control to function the power to the fireplace, it must be switch on.
4. At a distance of 4 to 6 feet (1.5 m to 2 m), point the remote control directly towards the
sensor.
A. Infrared Window
B. On/Off Switch
Press on/off switch to turn fire on.
To operate press once to
C. Flame Effect Dimmer
commence dimming cycle. During the dimming cycle the fire
will slowly dim then brighten allowing user to choose
suitable level. Press a second time to stop cycle when the
desired level is obtained. Failure to press dimmer a second
time will result in the fire dimming then brightening cycle
repeatedly.
D. Heater Maximum Heat (1350 W)
Press this once to
switch to high heat. The indicator light will come on as well
as the fan. Press again to turn off. (The fan will continue to
run for a few moments until sensors indicate cool condition).
E. Heater Low Heat (675W)
Press this once to switch to
low heat. The indicator light will come on as well as the fan.
Press again to turn off. (The fan will continue to run for a
few moments until sensors indicate cool condition).
F. Indicator Lamps will verify current activity. If you are unsure if heat is on or off check
the lamps on the control panel. If the function is ON in the indicator lamp will light
above the function switch.
12 | P a g e
TROUBLESHOOTING GUIDE ____________________________________________________
For any questions about the product, installations, returns and/or parts replacement, please call
Yosemite customer service at phone # 1-800-305-9872 or fax to 559-276-8738 and/or email us at
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Check that unit is plugged into a
standard 120V outlet.
2. Check that Main Power switch is in
“ON” position.
Power cord was not
plugged properly.
Fireplace does not turn on
1. Open the access panel and check if the
spinner motor is running properly.
2. If problem persists, unplug unit and
contact YHD customer service
Spinner motor does
not work.
Flame images freezes
Flame not bright or not
visible
Burned out light bulbs Replace light bulbs
Burned out light bulbs Replace light bulbs
Log set dim or not glowing
1. Refer to instruction manual
Heater is not turning ON
Improper operation
Normal operation
2. If problem persists, unplug unit and
contact YHD customer service.
This odor is normal condition caused by
the initial heating of internal parts and
will not occur again.
Heater emits an odor
Try turning On/Off button in the control
Heater does not blow warm
air
Heater or blower does panel several times to make sure it is at
not work properly.
ON position and the indicator light
should light up at the same time.
Fireplace makes a
grinding/rattling noise
The rod that spins the flame may need to
be greased.
Loose rod
13 | P a g e
WARRANTY
In the unlikely event of a problem occurring due to manufacturing fault within 24 months from the date
of purchase of the electric fireplace it will be repaired or replaced free of charge. Repair or replacement is
at the option of Yosemite Home Décor.
Defects must be brought to the attention of the Authorized Yosemite Home Décor Dealer from which you
purchased your appliance. Evaluation and course of action will be determined by the Authorized
Yosemite Home Décor Dealer. Please have proof of purchase, catalogue/model and or serial numbers
available when calling. Limited warranty requires a proof of purchase of the product.
What this limited warranty does not cover
This limited warranty does not cover consumable items such as the light bulbs and fuses which have a
limited lifespan.
This limited warranty does not apply to products that have been repaired (except by Yosemite Home
Décor or its authorized service representatives) or otherwise altered. This warranty does further not
apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, water damage,
improper maintenance or handling and operation with an incorrect power source.
www.yosemitehomedecor.com | 1-800-305-9872 Toll free
4250 West Shaw Avenue Fresno, CA 93722
14 | P a g e
|