Xerox WorkCentre M15/M15i
Quick Start Guide
604P13312
Document
Cover
Automatic Document
Feeder
Document
Input Tray
ADF Connector
Document
Guides
Document
Collate Tray
Document
Glass
Side
Cover
Bypass
Tray
USB Connector
Release
Latch
Telephone
Connections:
Front Cover
EXT.
LINE
Paper Cassette
Scanner Module
Output Tray
Control Panel
Parallel
Connector
AC Power Cord
Connector
On/Off
Switch
Unpacking
ꢀ Remove the plastic film from the
LCD.
1
2
3
Tape
LCD
ꢀ Remove all tapes and packing
materials.
ꢀ Pull the Scan Unlock Switch
located on the bottom of the
scanner module to unlock the
scanner.
Scanner
module
ꢀ Pull open the paper cassette
and remove the packing
material.
ꢀ Ensure the following components are available:
Telephone Line Cord
(M15i only)
USB Cable
AC Power Cord
Software
User
Documentation
Starter Toner
Cartridge
Drum
Cartridge
Page 3
Control Panel Overview
WorkCentre M15i
Pause PC
Printing
Copy/Fax/
Scan
Liquid Crystal
Display (LCD)
Job
Status
Menu/
Exit
Manual
Group
Manual
Dial
Clear/
Clear All
Stop
Start
Feature
Keys
Navigation
Keys
Error
Display
Enter
Redial/
Pause
Speed
Dial
Numeric
Keypad
WorkCentre M15
Pause PC
Printing
Liquid Crystal
Display (LCD)
Menu/Exit
Clear/
Clear All
Stop
Start
Error
Display
Enter
Numeric
Keypad
Feature
Keys
Navigation
Keys
Page 4
Making Connections
Use the following instructions to make the necessary connections required to
install the WorkCentre M15/M15i.
Automatic Document Feeder (ADF)
1
2
ꢀ Connect the Automatic
Document Feeder Cable to the
port shown and fasten the side
screws.
Note: The ADF is an option on the M15
Telephone Line (M15i only)
ꢀ Connect the Telephone Line
Cord from the wall jack to the
LINE jack.
ꢀ If required, connect an
answering machine and/or
telephone to the EXT jack.
Page 5
USB or Parallel Port Cable
3
4
CAUTION: Shut down the computer
before connecting the cable.
USB Cable
ꢀ Connect the USB Cable directly
to the PC.
OR
ꢀ Connect an IEEE1284 Parallel
IEEE1284 (Parallel Port)
Cable
Port Cable (sold separately).
Power
ꢀ Connect the AC Power Cord to
the machine and a power outlet.
ꢀ Press the ON/OFF switch to the
ON ( I ) position.
The machine displays
’WARMING UP PLEASE
WAIT...’
Page 6
Installing Cartridges
ꢀ Pull the release latch to open
the side cover.
1
ꢀ Open the front cover.
2
ꢀ Unpack the new drum cartridge.
Be careful not to touch the
surface of the drum.
3
ꢀ Slide the drum cartridge into the
slot on right side of the opening.
Page 7
ꢀ Remove the starter toner
cartridge from its packaging.
4
5
6
ꢀ Gently shake the cartridge to
loosen the toner.
Shaking the cartridge will
ensure maximum copies per
cartridge.
ꢀ Turn the toner locking lever
upwards.
ꢀ Slide the new toner cartridge in
until it locks in place.
ꢀ Turn the toner locking lever
downwards until it locks in
place.
ꢀ Close the front cover and the
side cover.
The product returns to Standby
mode.
Page 8
Loading Paper
ꢀ Pull open the paper cassette.
ꢀ Push down on the pressure
1
2
plate until it locks into position.
ꢀ Adjust the rear paper guide to
the required paper length.
It is preset to A4 or 8.5 x 11"
size depending on country.
LGL
FOLIO
A4
LT
R
ꢀ To load another size, lift the rear
guide out of the current position
and into the required position.
Rear
Guide
ꢀ Fan the paper and insert it into
the cassette.
3
ꢀ
The paper cassette can hold a maximum
of 550 sheets of 80 g/m (20 lb) plain
paper.
2
Page 9
ꢀ Ensure that the paper is
positioned under the snubber.
4
5
Do not fill above the maximum
fill line.
Max Fill
Line
Snubber
ꢀ Position the side guide by
squeezing the lever and sliding
it toward the stack of paper, until
it gently touches the side of the
stack.
Do not allow the guide to press
against the edge of the paper
tightly.
ꢀ Close the paper cassette.
Page 10
Setting Language (M15 only)
ꢀ Press [Menu/Exit], the first
WorkCentre M15
menu displays.
1
SYSTEM DATA
[PAPER SIZE...]
ꢀ Press [Enter].
ꢀ Scroll to ’SELECT LANGUAGE’
WorkCentre M15
using the
key.
2
SELECT LANGUAGE
[ENGLISH]
ꢀ Using the
or
navigation
keys select the language
required.
ꢀ Press [Enter].
Page 11
Setting Language and Country (M15i only)
ꢀ Press [Menu/Exit], the first
WorkCentre M15i
menu displays.
1
SYSTEM DATA
[PAPER SIZE...]
ꢀ Scroll to ’SYSTEM SETUP’
WorkCentre M15i
using the
key. Press [Enter].
SYSTEM SETUP
[RECEIVE MODE...]
2
3
ꢀ Scroll to ’SELECT LANGUAGE’
WorkCentre M15i
using the
key.
SELECT LANGUAGE
[ENGLISH]
ꢀ Using the
or
navigation
keys select the language
required.
ꢀ Press [Enter].
The COUNTRY option displays.
Note: The Country option is not applicable in North America and Canada. Changing the
country option will clear the memory.
Page 12
ꢀ Using the
or
navigation
WorkCentre M15i
keys, select [1: YES] to change
the Country option or [2: NO] to
leave the current setting and
select [Enter].
4
SELECT COUNTRY?
1: YES 2: NO
ꢀ If [1: YES] was selected, choose
the required option and press
[Enter].
WorkCentre M15i
SELECT COUNTRY
[
UK
]
ꢀ If necessary, press [Menu/Exit] to
save and exit.
Page 13
Setting the Local ID and Name (M15i only)
In some countries it is required by law to indicate the fax number on any fax
sent. The System ID containing the telephone number and a name (or
company name) will be printed at the top of each page sent from the
machine. Follow the instructions below to enter the machine’s System ID.
ꢀ Press [Menu/Exit], the first
WorkCentre M15i
menu displays.
1
SYSTEM DATA
[PAPER SIZE...]
ꢀ Scroll to ’SYSTEM ID’ using the
WorkCentre M15i
key.
SYSTEM ID
2
[TELEPHONE...]
Note: In some countries access to the
local ID by the user is not
permitted due to local regulations.
ꢀ Enter the fax telephone number.
WorkCentre M15i
If a number has already been
3
FAX:
entered it is displayed. Press
[Clear/Clear All] to delete the
current entry and enter the
correct number.
ꢀ Press [Enter] when the correct
telephone number displays.
Page 14
The display requests the ID.
WorkCentre M15i
ꢀ Enter a name or company name
ID:
4
using the numeric keypad.
KEY
ASSIGNED NUMBERS, LETTERS OR
CHARACTERS
1
2
3
4
5
6
7
8
9
0
1> Space
A > B> C > 2
D > E > F > 3
G > H > I > 4
J > K > L > 5
M > N > O > 6
P > Q > R > S > 7
T > U > V > 8
W > X > Y > Z > 9
+ > - > , > . > ‘ > / > * > # > & > 0
If a name has already been entered it is displayed. Press [Clear/Clear All] to
delete the current entry and enter the correct name.
Editing Numbers or Names
To correct a mistake, move the cursor under the wrong character by pressing
or
. Press the correct number to overwrite the incorrect character. If
[Clear/Clear All] is pressed, all the characters are deleted.
ꢀ Press [Enter] when the name on the display is correct.
ꢀ Press [Menu/Exit] to save and exit.
Page 15
Setting the Date and Time (M15i only)
The current time and date are shown on the display when the machine is on
and ready for faxing. The time and date are printed on all faxes sent. Follow
the instructions below to set the date and time.
ꢀ Press [Menu/Exit], the first
WorkCentre M15i
menu displays.
1
SYSTEM DATA
[PAPER SIZE...]
ꢀ Scroll to ’DATE & TIME’ using
WorkCentre M15i
the
or
key.
DATE & TIME
DDMMYY HH:MM
2
3
ꢀ Press [Enter].
ꢀ Enter the correct date and time
WorkCentre M15i
using the numeric keypad:
11-12-2002
15:00
Day
=
=
=
=
=
=
01 ~ 31
01 ~ 12
00 ~ 99
00 ~ 23 (24-hour mode)
01 ~ 12 (12-hour mode)
00 ~ 59
Month
Year
Hour
Minute
The date and time format is:
DD
MM
YY
HH:
MM
=
=
=
=
=
Day
Month
Year
Hour
Minute
ꢀ Press [Enter] when the correct
date and time displays.
ꢀ Press [Menu/Exit] to save and
exit.
Note: The clock format can be set to 12 or 24 hr in System Data Settings.
Page 16
Installing Software
Installing the drivers and other software will enable PC printing. Ensure the
WorkCentre M15/M15i is plugged in and connected to the computer’s
parallel or USB port before installing software from the CD.
Note: Windows 95 and Windows NT 4.0 do not support USB connection.
ꢀ Switch on the PC and start
Windows.
1
2
Note: If a window appears concerning
New Hardware, select Cancel.
ꢀ Insert the Driver CD into the CD-
ROM drive of the PC. If the
Xerox screen appears
automatically, go to step 3.
Run
ꢀ From the Start menu, select
Open: D:\XINSTALL.EXE
[Run].
ꢀ Type D:\XINSTALL.EXE ( “D” is
Browse...
Cancel
OK
the letter of the CD-ROM drive).
ꢀ Select [OK].
Page 17
ꢀ Follow the on-screen
instructions to complete the
software installation.
3
ꢀ After installing the software
reboot the PC.
ꢀ If the CD does not eject
automatically, remove before
rebooting.
Page 18
Using the WorkCentre M15/M15i
Making Copies
1
ꢀ Ensure ’READY TO COPY’
displays.
Status
ꢀ If not, press the [Copy/Fax/
Scan] key repeatedly until
’COPY MODE’ displays and
press [Enter].
WorkCentre M15
READY TO COPY
100%
001
ꢀ Load originals using the
Automatic Document Feeder or
the Document Glass.
Reduce/Enlarge %
Number of
Copies
ꢀ Select the Copy features
required, enter the quantity and
press Start.
Printing
2
ꢀ Open the application required
for the document and select an
existing document or create a
new document.
ꢀ Select [Print] from the File
menu. Ensure the WorkCentre
M15 Series is selected, and
program the print options
required for the job.
ꢀ Select [OK] on all dialog boxes
to print the job.
Page 19
Sending a Fax (M15i only)
3
4
ꢀ Load originals using the
Automatic Document Feeder or
the Document Glass.
Memory %
Available
Current
Date
ꢀ Ensure ’FAX’ displays. If not,
press the [Copy/Fax/Scan] key
repeatedly until ’FAX MODE’
displays and press [Enter].
WorkCentre M15i
11 - DEC - 2002
15:11
100%
FAX
ꢀ Select the Fax features
required, enter the fax number
and press Start.
Mode
Selected
Current Time
Scanning a Document to File (M15i only)
ꢀ Load originals using the
Automatic Document Feeder or
the Document Glass.
Status
ꢀ Start the scan application
program being used to acquire
the scanned image.
WorkCentre M15i
READY TO SCAN
ꢀ Follow the instructions provided
with the application program to
scan the document and retrieve
it at the PC.
Note: When using Paperport software to scan your job, the application will create a
separate file for each scanned page of the job. These separate pages can then
be merged within the Paperport application.
Page 20
ControlCentre 5.0
Using the Xerox WorkCentre M15i ControlCentre 5.0, Fax System Data
options can be set up, phonebook entries can be created and edited and
setup information can be viewed on the PC. When Xerox WorkCentre M15/
M15i software is installed the Xerox WorkCentre M15i ControlCentre 5.0
utility is installed automatically.
ꢀ
WorkCentre M15 can only use ControlCentre 5.0 to upgrade firmware.
WorkCentre M15i can use the full funtionality of ControlCentre 5.0.
Running ControlCentre 5.0
1
ꢀ Click the [Start] button on the
desktop computer.
ꢀ From Programs, select [Xerox
WorkCentre M15i], then
[ControlCentre 5.0].
The ControlCentre 5.0 screen
appears.
Page 21
Using ControlCentre 5.0
2
ꢀ Select a tab and program the
options required.
Note: When the settings are changed, the
machine and ControlCentre 5.0 will
be automatically updated to the
latest settings made on either the
machine or on ControlCentre 5.0.
ꢀ To exit ControlCentre 5.0, click
the [Exit] button on the bottom of
each tab screen.
ꢀ For further details, click the [Help]
button.
Page 22
Further Assistance
If assistance is required please call our experts at the Xerox Welcome
Center, or contact the local representative. When telephoning please quote
the machine Serial Number. Use the space below to make a note of the
machine serial number:
#_________________________________________________________
To access the serial number open the side cover using the release latch and
then open the front door. The Serial Number is located on the panel above
the print cartridge.
The Xerox Welcome Center or local representative telephone number is
provided when the WorkCentre M15/M15i is installed. For convenience and
future reference, please record the telephone number in the space below:
Welcome Center or local representative Telephone Number:
Xerox US Welcome Center: 1-800-821-2797
Xerox Canada Welcome Center: 1-800-93-XEROX (1-800-939-3769)
Page 23
Notes
Page 24
|