Wtb Float 80rlc User Manual

2002 FOX FORX Owners Manual  
FLOAT 80R - FLOAT 80RL - FLOAT 80RLC  
FLOAT 100R - FLOAT 100RL - FLOAT100RLC  
Vanilla 100R - Vanilla 100RL - Vanilla 100RLC  
Vanilla 125R - Vanilla 125RL - Vanilla 125RLC  
FOX RACING SHOX  
130 Hangar Way, Watsonville, CA 95076  
831.768.1100 FAX 831.768.9342  
Table of Contents  
Introduction ................................................................. 4  
Contact Information ..................................................... 4  
Service / Warranty ....................................................... 4  
International Service Centers ....................................... 4  
Warranty Policy ........................................................... 5  
Methods of Payment ................................................... 5  
Method of Shipping ..................................................... 5  
Disclaimer ................................................................... 5  
Consumer Safety ........................................................ 5  
Important Safety Information ........................................ 6  
Installation .................................................................. 6  
Tire Sizes ................................................................... 7  
Brakes ........................................................................ 7  
Maintenance ............................................................... 7  
Service Intervals .......................................................... 8  
Pump  
.................................................................... 8  
General Set-Up Instructions ......................................... 9  
Fork Terminology ........................................................ 9  
Sag & Spring Tuning  
Vanilla Forx .................................................. 9  
FLOAT Forx ............................................... 10  
Damping Adjustment Guidelines ................................ 11  
Changing Travel  
FLOAT Forx ............................................... 12  
Vanilla Forx ................................................ 13  
Changing Oil ............................................................. 14  
Seals and Foam Rings .............................................. 16  
International Versions  
Français .................................................................. 17  
Italiano .................................................................. 33  
Deutsch .................................................................. 49  
Español .................................................................. 65  
Japanese ................................................................. 81  
3
Introduction  
Congratulations on choosing FOX FORX for your bicycle. In doing so, you have chosen the best suspension fork in the  
industry! All FOX Racing Shox products are designed, manufactured and assembled by the finest professionals in the  
industry. As a consumer and supporter of FOX Racing Shox products, you need to be aware of the importance of setting  
up your fork correctly to ensure maximum performance. This manual will provide you with the step-by-step instructions of  
how to set up your fork. It is a good idea to keep your receipts with this manual and refer to it for service and warranty  
issues.  
Contact Information  
FOX Racing Shox  
130 Hangar Way  
Watsonville, CA 95076  
Phone: 831.768.1100  
North America: 800.369.7469  
Fax: 831.738.9312  
Website: www.foxracingshox.com  
Business Hours: Monday-Friday 8:00AM-5:00PM Pacific Time  
Service / Warranty  
FOX Racing Shox is pleased to offer 48-hour* turnaround for product service, provided the following steps are taken.  
1. Contact FOX Racing Shox at 800.FOX.SHOX to obtain a Return Authorization (R.A.) Number and shipping address.  
For International Service Centers, please refer to the list below or contact FOX Racing Shox to determine the Service  
Center nearest you.  
2. Satisfactory proof of purchase receipt is required for warranty consideration.  
3. Mark the Return Authorization Number and the Return Address clearly on the outside of the package and send item  
to FOX Racing Shox or your International Service Center with shipping charges pre-paid by sender.  
4. Include a description of the problem, bicycle information (manufacturer, year and model), type of FOX product,  
spring rate and return address with daytime phone number.  
*International Service Centers operate independently. Service and Warranty turnaround times may vary.  
International Service Centers  
Country  
Australia  
Name  
Phone Number  
612-9679-8400  
087-631980  
E-mail  
Dirt Works  
Belgium  
Sabma  
Brazil  
Plimax 2 Fast  
Cycle Works  
Velo Cycle  
5511-251-0633  
780-440-3200  
Canada West  
Canada East  
France  
514-849-5299  
F.M.F. France  
Shock Therapy  
Pepi Innerhofer  
Mom & Pop's  
Blue Shark Ent.  
Dirt Racing  
33-494-54-1950  
49-6126-22677-00  
39-0473-56-3107  
81-586-43-6810  
64-4589-4535  
support@shock-therapy.com  
Germany  
Italy  
Japan  
New Zealand  
Spain  
34-91-663-71-25  
41-31-809-3020  
44-1633-615-815  
831.768.1100  
Switzerland  
United Kingdom  
United States  
FOX Racing Euro  
Mojo Suspension  
FOX Racing Shox  
4
Warranty Policy  
The factory warranty period for your fork is one year from the original date of purchase of the bicycle or fork. A copy of the  
original purchase receipt must accompany any fork being considered for warranty service. Warranty is at the full discre-  
tion of FOX Racing Shox and will cover only defective materials and workmanship.  
This warranty is void when damage to the fork has occurred from the following:  
Abuse  
Seal damage due to power washing  
Damage to the exterior finish caused by improper cable routing, rocks, crashes, dents  
Any attempt to disassemble damper assembly  
Modifications  
Non-Factory oil use or improper service  
Shipping damages or loss (purchase of full value insurance is recommended)  
To ensure peak performance, repairs and service to the fork must be performed by FOX Racing Shox in the USA or  
outside the USA by a FOX Racing Shox Authorized Service Center.  
FOX Racing Shox reserves the right to all final warranty or non-warranty decisions.  
Method of Payment  
Visa, MasterCard and/or Cashier’s Check  
Method of Shipping  
FOX Racing Shox uses UPS Ground service within the USA.  
Disclaimer  
FOX Racing Shox is not responsible for any damages to you or others arising from riding, transporting, or other use of  
your fork or bicycle. In the event that your fork breaks or malfunctions, FOX Racing Shox shall have no liability or  
obligation beyond the repair or replacement of your fork, pursuant to the terms outlined in the Service and Warranty  
provisions of this Manual.  
Consumer Safety  
RIDING A BICYCLE IS DANGEROUS AND CAN RESULT IN DEATH OR SERIOUS INJURY. TAKE YOUR RESPONSIBIL-  
ITY TO YOURSELF AND OTHERS SERIOUSLY.  
Maintain your bicycle and suspension  
Always wear a helmet, protective clothing and eye protection  
Ride within your limits  
Tread lightly  
Your bike is equipped with FOX Racing Shox suspension. Before riding, take the time to read the FOX Racing Shox  
manual on setup, use, and service of your fork. If you have questions, call your Authorized FOX Racing Shox Service  
Center or call FOX Racing Shox directly at 831.768.1100.  
If your fork ever loses oil, or if it makes unusual noise, stop riding immediately and have the fork inspected by a dealer,  
Service Center or contact FOX Racing Shox. RIDING WITH A BROKEN OR MALFUNCTIONING FORK CAN RESULT IN  
LOSS OF CONTROL, CRASHING, AND POSSIBLE DEATH OR SERIOUS INJURY.  
Never modify your bike frame or fork. Only use genuine FOX Racing Shox parts for your fork. Any modification, improper  
service, or use of after-market replacement parts will void the warranty and could damage the fork or cause loss of control  
of the bike resulting in serious injury or death.  
Follow the scheduled service recommendations in this manual. Always have your fork serviced by a qualified bicycle  
mechanic, dealer or Authorized FOX Racing Shox Service Center.  
5
Important Safety Information  
1. Verify that the brakes are installed and adjusted properly before riding the bicycle. Improperly installed or adjusted  
brakes can cause loss of control and serious or fatal injuries to the rider. Use only “V” - style or hydraulic cantilever  
brakes or disc brakes designed by the manufacturer for use on FOX FORX. Do not use brace mounted cable leverage  
devices. Do not route brake cables or housing through the stem.  
2. If your fork loses oil, tops out excessively or makes unusual noises, immediately stop riding and contact FOX Racing  
Shox or an Authorized FOX Racing Shox Service Center for inspection. Continued use of the fork could cause loss of  
control and serious or fatal injuries.  
3. Use only FOX Racing Shox replacement parts. Using aftermarket parts on FOX FORX will void the warranty.  
Aftermarket replacement parts could also cause structural failure resulting in loss of control and serious or fatal  
injuries.  
4. If mounting the bicycle in a carrier designed to hold a fork by its drop-outs, use caution to not tilt the bicycle to either  
side. Tilting the bike with the drop-outs in the carrier can cause structural damage to the fork. Ensure that the fork is  
fastened securely with the quick release and that the rear wheel is properly held. If the bicycle ever tilts or falls from a  
bicycle carrier, do not ride it until it is examined by a qualified dealer, Service Center or FOX Racing Shox. A fork leg or  
drop-out failure could cause loss of control and serious or fatal injuries.  
5. FOX FORX do not include reflectors for on-road use. FOX FORX are designed to be used in competitive off-road riding  
and racing. Proper reflectors meeting the Consumer Product Safety Commission’s (CPSC) requirements should be installed  
if the fork will be used on public roads.  
6. FOX FORX have a crown / steerer / upper tube assembly. These parts are pressed together in a one-time,  
precision press-fit operation. Replacement of any of these parts requires a complete new assembly. Do not  
attempt to remove or replace the steerer or upper tubes independently of the crown. DO NOT ATTEMPT TO  
ADD THREADS TO THREADLESS STEERERS. Modifying the crown / steerer / upper tube assembly as de-  
scribed here could cause the rider to lose control of the bicycle resulting in serious or fatal injuries.  
Installation  
Step 1 - Your FOX FORX should be installed by a qualified bicycle mechanic. Forks installed improperly are dangerous  
and can cause loss of control and serious or fatal injuries.  
Step 2 - Remove existing fork from the bicycle. Remove the crown race from the fork. Measure the steerer tube length  
of the existing fork. Transfer this measurement to the FOX FORX steerer. Refer to stem manufacturer’s  
instructions to be sure there will be enough clamping surface for the stem. If it is necessary to cut the  
steerer tube, measure twice and cut once. It is also recommended that a cutting guide be used while cutting  
the steerer tube.  
Step 3 - Use a crown race setter to install the crown race firmly against the top of the crown. Install the star fangled  
nut in the steerer tube. This should be done with a star fangled nut installation tool.  
Step 4 - Install the fork on the bicycle. The headset should be adjusted so it turns freely without drag or free play.  
Step 5 - Re-install the brakes and adjust the brake pads. Refer to the brake manufacturer’s instructions.  
Step 6 - Mount the front wheel being sure that the quick release nuts sit in the fork drop-out counter bores. The quick  
release should engage four (4) or more threads. Close the quick release with the lever in front of and  
parallel to the left fork leg.  
6
Tire Sizes  
FOX FORX will accept tires sizes up to 2.40 inches wide (e.g. WTB  
MotoRaptor 55/60, 26 x 2.40). Any tire larger than 26 x 2.30 must be  
checked for clearance by the following method.  
Determining Tire Size - With the tire installed and inflated on the  
rim, measure the following three  
dimensions.  
Maximum  
Peak Tire  
Diameter  
Maximum  
Edge Tire  
Diameter  
Maximum Peak Tire Diameter = 343mm = 27.00 inch  
Maximum Edge Tire Diameter = 326mm = 25.67 inch  
Maximum Tire Width  
=
61mm = 2.40 inch  
Do not use a tire if ANY measurement exceeds the maximum  
dimensions shown above. Using tires larger than the dimen-  
sions  
shown above is NOT RECOMMENDED and can cause serious  
or fatal injury.  
Brakes  
Maximum  
Tire Width  
Linear-pull Brakes  
Linear-pull brakes (i.e. V-brakes) can be used on FOX FORX. Use only the FOX brake posts supplied with the fork.  
Install brake posts and torque to 80 in-lbs. Install and adjust linear-pull brakes according to the manufacturer’s recom-  
mendations. Test brakes for proper operation on flat land. FOX FORX use a hangerless lower leg design and cannot  
use any cantilever style brakes.  
Disc Brakes  
Disc brakes with 160-180mm rotors can be used on FOX FORX. Do not use DH rotors larger than 180mm. Install  
disc brakes and torque all fasteners according to manufacturer’s recommendations. Install, route and check that all  
cables or hydraulic hoses are securely fastened to the lower leg and will not move during compression of the fork. Test  
brakes for proper operation on flat land.  
Maintenance  
Performance, safety and the life-span of your FOX FORX depend on maintenance. If you ride in extreme conditions,  
service and maintain your FOX FORX more frequently.  
NOTE: In this manual, reference being made to the left and right side of the fork is from the seated rider’s perspective.  
Important Check Before Every Ride  
1. Check that quick release skewer is properly adjusted and tight.  
2. Clean the outside of your fork with soap and water and wipe dry with a soft dry rag. Do not spray water directly  
on the Seal/Uppertube junction. DO NOT USE A HIGH PRESSURE WASHER ON YOUR FORK.  
3. Inspect entire exterior of fork for damage. The fork should not be used if any of the exterior parts appear to be  
damaged. Please contact your local dealer or FOX Racing Shox for further inspection and repair.  
4. Check headset adjustment. Adjust headset if loose according to manufacturer’s recommendations.  
5. Check that brake cables or hoses are properly fastened.  
6. Check that the front and rear brakes operate properly on flat land.  
7
Service Intervals  
Your FOX FORX will perform best if serviced at the regular intervals shown below.  
After Each  
Ride  
Every 25  
Hours  
Every 100  
Hours  
Instructions  
found on:  
Item  
Annually  
X
Wash and Dry Exterior of Fork  
page 7  
page 16  
page 15  
page 14  
page 14  
Clean Fork Seals & Inspect /  
Lube Foam Rings  
X
Clean and Refill FLOAT Fluid in  
Air Chamber (FLOAT Forx Only)  
X
X
X
Bushing Wear Inspection  
Change Fork Oil  
Required Tools and Supplies  
Safety Glasses  
Bucket or Drain Pan  
Paper towels and/or rags  
Plastic Faced Mallet  
Torque Wrench  
Torque Setting  
n/a  
n/a  
Used for:  
Protecting Eyes  
Changing Oil / Travel  
Absorbing oils & fluids  
Tap loose bottom shafts  
Torque fasteners  
Travel change (FLOAT Forx)  
Oil change (All Forx)  
n/a  
n/a  
n/a  
FOX Suspension Fluid  
FOX FLOAT Fluid  
FOX High Pressure Air Pump  
26mm 6 point socket  
10mm open-end or socket wrench  
8mm Crawfoot socket wrench  
3/8” Deep socket wrench  
Schrader valve core wrench  
2mm Hex-key wrench  
n/a  
n/a  
Travel & Oil change (FLOAT Forx)  
Setting air pressure (FLOAT Forx)  
All Topcaps  
All Bottom Nuts  
Brake Posts  
Air Tank Valve ( FLOAT Forx)  
Schrader Valve Core (FLOAT Forx)  
Rebound Knob (R, RL, RLC)  
Blow-off Threshold Knob (RLC)  
165 in-lbs (1864 N-cm)  
50 in-lbs (565 N-cm)  
80 in-lbs (904 N-cm)  
75 in-lbs (847 N-cm)  
4 in-lbs (45 N-cm)  
11 in-lbs (124 N-cm)  
4 in-lbs (45 N-cm)  
1.5mm Hex-key wrench  
Seated, back-off 1/4 turn Lockout Lever (RL, RLC)  
Pump  
A FOX high pressure air pump is available for FLOAT Forx. It is used to make changes in air pressure on your fork.  
1. Remove the air topcap from the top of the left fork leg.  
2. Thread the pump’s valve chuck onto the fork’s air-valve until pressure registers on the pump gauge. This takes  
approximately 6 turns. Do not over-tighten pump on air-valve as this will damage the pump chuck seal.  
3. To increase the pressure, stroke the pump a few cycles. The pressure should increase slowly. If pressure increases  
rapidly check to make sure the pump is properly fitted and tightened onto the air valve.  
Note: If the fork has no air pressure, the gauge will not register pressure.  
4. To decrease the pressure push the black bleed-valve. Pushing the bleed-valve halfway down, and holding it there,  
will allow pressure to escape from the pump and fork. Pushing the bleed-valve all the way down and releasing it  
will release a small amount of pressure (micro-adjust). When unthreading the pump from the air-valve fitting,  
the sound of the air loss is from the pump hose, not the fork itself.  
Note: When attaching the pump to the fork, the hose will need to fill with air. This will result in a lower pressure  
registering approximately 10 to 20 PSI on the gauge.  
Note: Average setting range is from 45 to 125 PSI. DO NOT EXCEED 200 PSI.  
5. Replace the air topcap before riding.  
8
General Set-Up Instructions  
Fork Terminology  
Travel: The total amount the fork compresses.  
Sag: The amount the fork compresses with the rider sitting on the bike in a normal riding position.  
Compression Damping: This controls the rate at which the fork compresses  
Rebound Damping: This controls the rate at which the fork extends.  
Preload: The initial force place on a spring.  
Spring Rate: The amount of force required to compress a spring one inch.  
FLOAT: This is FOX air spring technology.  
Vanilla: This is FOX coil spring technology.  
Vanilla Forx  
Setting Sag on Vanilla Forx  
To get the best performance from your FOX Vanilla fork, it is necessary to set and adjust sag. Sag is how much the  
fork compresses or “sags” when the rider sits on the bicycle. Generally, this is 15-25% of the total travel.  
Measuring and adjusting sag  
1. Install a zip tie on the upper tube and push it down until it contacts the fork seal. Carefully sit on  
the bike and assume a normal riding position. The fork should compress slightly. Being careful  
not to further compress the fork, dismount the bicycle. Measure the distance between the seal  
and the zip tie. This distance is the sag.  
2. Compare your sag measurement to the table.  
If your sag is lower than on the table, turn the preload knob counter-clockwise one (1) full  
turn. Measure sag again and repeat adjustment if necessary.  
If your sag is higher than on the table, turn the preload  
knob clockwise one (1) full turn. Measure sag again and  
repeat adjustment if necessary.  
Vanilla Forx Sag Table  
Travel  
80mm  
Sag  
If correct sag cannot be achieved by adjusting the preload knob,  
see the Spring Tuning Guide below.  
Spring Tuning on Vanilla Forx  
Read the Vanilla Spring Tuning Guide chart below to see if you need to change your  
spring rate. Vanilla Forx are tuned by changing only the left side coil spring.  
The coil spring has a painted color code stripe on one end of the spring.  
Refer to the chart to select the optimum spring.  
16mm ( 5/8")  
20mm (13/16")  
25mm (1")  
100mm  
125mm  
Vanilla Forx Spring Chart  
Vanilla Spring Tuning Guide  
Symptom  
Spring  
Rate  
Color  
Code  
Travel  
Range  
FOX Part #  
Notes  
Do the following:  
Measured sag is too low  
and Preload Knob is  
adjusted fully counter-  
clockwise.  
039-05-000-A 10 lb/in Black 80-100-125  
039-05-007-A 18 lb/in Purple 80-100-125  
Increase spring rate  
Standard on  
Vanilla 125  
Excessive bottoming of  
travel during riding.  
039-05-001-A 25 lb/in  
Blue  
80-100-125  
Increase spring rate  
Decrease spring rate  
Decrease spring rate  
Standard on  
Vanilla 100  
Measured sag is too high  
and Preload Knob is  
adjusted fully clockwise.  
039-05-002-A 35 lb/in Green 80-100-125  
039-05-003-A 45 lb/in Yellow 80-100-125  
039-05-004-A 60 lb/in Orange 80-100 only  
Standard for  
80mm travel  
Ride is too harsh and  
never use full travel.  
039-05-005-A 75 lb/in  
Red  
80-100 only  
9
Changing your Coil Spring  
1. With a 26mm 6-point socket wrench, loosen and remove the preload topcap. Remove the black spring spacers  
(two spacers for 125mm travel, 1 for 100mm travel, none for 80mm travel). Compress the fork slightly and remove  
the coil spring. You may need to firmly pull up on the spring to disengage it from the plunger shaft. Wipe the spring  
dry with a rag and check the color code.  
2. Install the new spring by dropping it into the upper tube. Install the spacer(s). Install and torque the topcap to 165  
in-lbs (1864 N-cm).  
3. Measure and adjust sag as described on page 10. Happy Trails!  
FLOAT Forx  
Setting Sag on FLOAT Forx  
To get the best performance from your FOX FLOAT fork, it is necessary to set and adjust sag. Sag is how much the  
fork compresses or “sags” when the rider sits on the bicycle. Generally, this is 15-25% of the total travel.  
Measuring and adjusting sag  
1. Install a zip tie on the upper tube and push it down until it contacts the fork seal. Carefully sit on  
the bike and assume a normal riding position. The fork should compress slightly. Being careful  
not to further compress the fork, dismount the bicycle. Measure the distance between the seal  
and the zip tie. This distance is the sag.  
2. Compare your sag measurement to the table.  
If your sag is lower than on the table, remove the air topcap, screw on the FOX High  
Pressure Air Pump fitting, note the current air pressure setting and depress the black  
bleed-valve to reduce the gauge pressure by 5 psi. Measure sag again and repeat  
adjustment if necessary.  
FLOAT Forx Sag Table  
If your sag is higher than on the table,  
XC/Race  
Firm  
Freeride  
Plush  
TRAVEL  
80mm  
remove the air topcap, screw on the FOX High  
Pressure Air Pump fitting, note the current air  
pressure setting and pump to increase the gauge  
pressure by 5 psi. Measure sag again and repeat  
adjustment if necessary.  
12mm  
(1/2")  
20mm  
(13/16")  
15mm  
(9/16")  
25mm  
(1")  
100mm  
Air Spring Tuning on FLOAT Forx  
Read the FLOAT Air Spring TuningGuide chart below to see if you need to change your air pressure. FLOAT Forx are  
tuned by changing air pressure at the left topcap. (See page 8 for instructions for the FOX High Pressure Air Pump)  
FLOAT Air Spring Tuning Guide  
FLOAT Air Spring Guidelines  
Symptom  
Do the following:  
Rider Weight  
Under 125 lbs  
125 - 135 lbs  
135 - 145 lbs  
145 - 155 lbs  
155 - 170 lbs  
170 - 185 lbs  
185 - 200 lbs  
200 - 215 lbs  
215 - 230 lbs  
230 - 250 lbs  
Air Pressure  
45 psi  
Measured sag is too  
low.  
Increase air  
pressure by 5 psi  
50 psi  
Excessive bottoming  
of travel of travel  
during riding.  
Increase air  
pressure by 5 psi  
55 psi  
65 psi  
Measured sag is too  
high.  
Decrease air  
pressure by 5 psi  
75 psi  
85 psi  
Ride is too harsh and  
never use full travel.  
Decrease air  
pressure by 5 psi  
95 psi  
105 psi  
115 psi  
125 psi  
10  
Damping Adjustment Guidelines  
Rebound Adjustment (R, RL, RLC)  
FOX FORX feature a rebound adjuster. This allows the rider to control the  
speed at which the fork extends after compression. The Rebound Adjustment  
Knob is the red knob located on top of the right fork leg. Turn it clockwise for  
slower rebound and counter-clockwise for faster rebound. There are 12 clicks  
of adjustment in the full range of motion. The proper rebound setting is a  
personal preference and varies depending upon spring preload, spring rate  
and riding style. Rebound should be as fast as possible without kicking back. If  
the rebound is too slow the suspension will not function properly and the wheel  
will not follow the changing terrain. Determining the proper rebound setting  
may take a few rides to fine tune. On those first few rides adjust the rebound and  
note the different ride characteristics. Your rebound adjustment may change for  
different riding conditions. As a starting point for tuning your rebound adjustment,  
turn the rebound adjuster knob all the way clockwise until it stops, then turn  
counter-clockwise 6 clicks.  
R
Compression Lock-out Lever (RL, RLC)  
The blue compression lock-out lever is located below the red rebound  
adjuster knob. It allows the rider to close the compression damping in the  
fork. This keeps the fork at the top of its travel and it will be hard to com-  
press. The fork is said to be “locked-out” in this position. Rotate the lever  
clockwise to the six o’clock position to achieve lock-out. This position is  
useful in climbing and sprinting situations. The fork will “blow-off” in the  
event that a big hit is encountered with the fork locked-out. To unlock the  
fork, simply rotate the lever counter-clockwise to the three o’clock position.  
This puts the cartridge in “open” mode and you will have normal compres-  
sion damping. The lock-out lever will rotate past the three o’clock position.  
This is normal and does not affect performance.  
Note: The fork may cycle a couple times after activating the lock-out. Once  
complete lock-out is achieved, the fork may continue to move 3-5mm. This  
is normal and does not affect performance.  
RL  
Compression Adjustment (RLC Only)  
Low-speed compression damping is adjusted with the blue bezel ring below  
the blue lockout lever. Compression damping controls the quickness with  
which the fork moves through its travel. Rotate the bezel clockwise for slower  
(harder) compression and counter-clockwise for faster (easier) compression.  
There are 9 clicks of adjustment. The proper setting is a personal preference  
and varies depending on your weight and riding style. Determining the proper  
compression setting may take a few rides to fine tune. On those first few rides  
adjust the compression and note the different ride characteristics. Your  
compression damping setting may change with different riding conditions. As a  
starting point for tuning your compression, turn the bezel clockwise until it  
stops, the back off 5 clicks.  
RLC  
Blow-off Threshold Adjustment (RLC Only)  
FLOAT RLC and Vanilla RLC feature Blow-off Threshold  
Adjustment capabilities. It is adjusted with the blue knob  
located at the bottom of the right fork leg. This gives the rider  
the ability to adjust the force required to cause the fork to  
blow-off when it is in the locked-out position. Turn the knob  
clockwise to make it harder to blow-off and counter-clockwise  
to make it easier. There are twelve (12) clicks of adjustment in  
the full range of motion. As a starting point for tuning your  
blow-off threshold, turn the knob all the way clockwise until it  
stops, then back off one click.  
RLC  
11  
Changing Travel - FLOAT Forx  
FOX FORX travel can be changed by rearranging the travel spacers as shown in the drawings below. After changing  
travel check the fork for proper operation before riding. If there is free movement in the fork or if it makes strange  
noises disassemble the fork and check for complete number and correct orientation of spacers.  
Step 1 - Remove the blue air cap from the top of the left fork leg. Let the air out of the fork. Refer to Pump Instructions  
for details about letting the air out with a pump. Remove left top cap with a 26mm socket 6-point socket  
wrench.  
Step 2 - Loosen the bottom nut 3-4 turns with a 10mm wrench. With a plastic mallet, gently tap the bottom of the shaft  
to disengage it from the lower leg. Allow oil to drain into a bucket. Remove the bottom nut and crush washer.  
Step 3 - Compress the fork as much as possible. The air piston will be visible about one inch below the top of the  
upper tube. Push the bottom of the shaft upwards to push the air piston out of the top of the upper tube. If  
necessary, use a small screwdriver to push the bottom of the shaft up through the hole in the bottom of the  
lower leg.  
Step 4 - Pull the air-shaft assembly from the fork. Refer to the drawings below and add or remove the appropriate  
spacer(s) to achieve the desired travel. NOTE: FLOAT FORX can be configured for 80 or 100mm of travel. Do  
not exceed 100mm of travel. Spacers snap on to the air shaft between the Spring Guide and the Topout  
Plate.  
Step 5 - Lubricate the o-ring on the air piston with FOX FLOAT Fluid and re-install the air shaft assembly into the  
upper tube. Push the shaft until it approaches the bottom hole of the fork. Do not push the shaft all the way  
through the bottom hole.  
Step 6 - Turn the fork upside down. Pour 30cc of FOX Suspension Fluid through the bottom hole.  
Step 7 - Push the air shaft assembly up until the shaft comes through the bottom hole. Install the crush washer and  
bottom nut. Torque to 50 in-lbs.  
Step 8 - Turn the fork right side up. Pour 5cc of FOX FLOAT Fluid on top of the air piston.  
Step 9 - Lubricate the o-ring on the air topcap with FOX FLOAT Fluid. Re-install the topcap and torque to 165 in-lbs.  
Step 10 - Air up the fork to the desired pressure and cycle it several times to check for proper operation. Re-install the  
blue air cap.  
100mm  
80mm  
Bottom Nut and Crush Washer  
Air topcap  
Air piston  
Air Shaft  
Assembly  
Negative  
Spring  
Retainer  
Negative  
Spring  
Plate  
20mm Travel  
Spacer  
12  
FLOAT Forx Travel Spacer Diagram  
Changing Travel - Vanilla Forx  
FOX FORX travel can be changed by rearranging the travel spacers as shown in the drawings below. After changing  
travel check the fork for proper operation before riding. If there is free movement in the fork or if it makes strange  
noises disassemble the fork and check for complete number and correct orientation of spacers.  
The following tools and supplies will be needed: 26mm 6-sided socket, 10mm wrench, 2mm hex wrench, 1.5mm hex  
wrench, torque wrench, plastic faced hammer, small screw driver, drain pan, FOX Suspension Fluid.  
Step 1 - Step 1a -Remove the left (spring side) top cap with a 26mm 6-sided socket.  
Step 1b -On R models, simply remove the right (cartridge) side top cap with a 26mm 6-sided socket.  
Step 1c -RL and RLC models require that the adjuster knobs be removed as shown in the drawing (see  
page 14. Remove the red rebound knob by firmly holding the red knob from turning and loosen  
screw with a 2mm hex wrench.  
Step 1d -Remove the lock-out lever with a 1.5mm hex wrench by loosening the three set screws and  
carefully lifting the lever. Do not remove the set screws. The 3 balls are held in place by grease.  
Do not lose the three balls in the lock-out lever.  
Step 1e -Remove the low-speed compression knob on RLC models. Below the low-speed compression  
knob is a detent ball and spring which sit in a counterbore in the topcap. Check that the ball is  
positioned in the hole by pressing on it with a small screwdriver and feeling for the force of the  
spring.  
Step 1f - Loosen and unscrew the damper topcap with a 26mm 6-sided socket.  
Step 2 - Compress fork slowly until the travel spacers are exposed on the damper side. Pull the damper topcap up  
until it stops. Snap on or off the correct length spacers to match the orientation shown in the Travel Spacer  
Diagram (see page 14). If removing spacers from the cartridge, make sure to keep them in a safe place for  
future use.  
Step 3 - Step 3a - Extend the fork by pulling down on the lower leg. Push down on the damper topcap and carefully  
thread into upper tube. Torque to 165 in/lbs.  
Step 3b -Re-install adjuster knobs. On RLC models, install the low speed compression knob so that the  
groove on the bottom is positioned over the aluminum pin in the topcap.  
Step 3c -On RL and RLC models, install the lockout lever onto the hex and rotate clockwise until it stops. It  
may take multiple rotations to seat the lockout shaft. Orient the lever so the lockout tab faces  
approximately the six o’clock position. While pressing the lockout lever down, lightly tighten the  
three set screws. Back each screw off 1/4 turn.  
Step 3d -On all models, install red rebound knob so that the slot feature on the bottom is aligned with the  
flats on the center of the rebound shaft. Apply blue loctite to screw and tighten with 2mm hex  
wrench while holding red rebound knob from spinning.  
Warning - Damper internals will be damaged if the rebound knob is not held turning while the  
screw is tightened.  
Step 4 - Loosen the left (spring side) with a 10mm wrench or socket 3-4 full turns. Place a clean drain pan under the left leg  
and tap lightly with a plastic hammer on the nut to loosen the plunger from the lower leg. Unscrew and remove  
bottom nut and washer. Push up on the shaft and let oil drain.  
Step 5 - Make sure all oil is drained from left side leg and right topcap is tight. Turn bike upside down and push out  
plunger shaft.  
Step 6 - Looking at the Travel Spacer Diagram, add or remove spacers between the black negativespring guide and  
the aluminum coil insert. Spacers snap onto the shaft. Slide the black negative spring guide up against the  
spacers.  
Step 7 - Reinstall the plunger shaft, spring and spacers into the left fork leg and install the crush washer and bottom  
nut. Torque the bottom nut to 50 in-lbs.  
Step 8 - Pour in 30cc of new FOX Suspension Fluid or re-use oil from clean drain pan into the left upper tube.  
Step 9 - Install left top cap and torque to 165 in-lbs.  
Step 10 - Cycle the fork several times to check for proper operation before riding. If there is free movement in the fork  
or if it makes strange noises, disassemble fork to check for complete number and orientation of spacers.  
13  
Changing Travel - Vanilla Forx con’t  
80mm 100mm  
125mm  
Adjuster Knobs  
Preload  
Topcap  
All Forx  
Travel  
Spacers  
25mm  
20mm  
20mm  
Main  
Spring  
RL, RLC  
RLC Only  
25mm  
20mm  
Negative  
Spring  
Guide  
25mm  
Plunger  
Shaft  
20mm  
25mm  
20mm  
Vanilla Forx Travel Spacer Diagram  
Bushings  
Bushings should be checked annually for excessive wear. If fore and aft movement is detected between the upper tubes and  
lower legs, contact an Authorized FOX Racing Shox Service Center or FOX Racing Shox for further instructions. Grasp the  
lower legs at the drop outs (axle). Push the fork straight back towards the rear wheel. Then pull it towards you. There should  
not be any free movement or clicking sounds. Next grasp the fork near the upper tube/seal junction and try the same thing.  
Once again there should be no free movement. If any movement is noticed, refer to page 4 of this manual and contact FOX  
Racing Shox or and Authorized FOX Racing Shox Service Center.  
Changing Oil  
Vanilla Forks - Left Side  
The left leg of FOX Vanilla Forx contain the parts shown on the Vanilla Travel Spacer Diagram.  
The following tools and supplies will be needed: 26mm 6-sided socket, 10mm wrench, 2mm hex wrench, 1.5mm hex  
wrench, torque wrench, plastic faced hammer, small screw driver, drain pan, FOX Suspension Fluid.  
Step 1 - Remove the Preload Topcap with a 26mm socket wrench. Remove all of the travel spacers from the top  
of the main spring.  
Step 2 - Loosen the bottom nut 3-4 full turns with a 10mm wrench. Place a drain pan under the fork leg and then  
lightly tap the bottom nut with a plastic faced hammer to loosen the shaft from the lower leg. Remove bottom  
nut and crush washer. Push plunger shaft up into the lower leg with a small screwdriver and let the oil drain  
from the fork leg.  
Step 3 - With all the oil drained, use the small screwdriver to carefully guide the plunger shaft back down through the  
hole in the bottom of the lower leg. Install the crush washer and bottom nut. Torque bottom nut to 50 in-lbs.  
Wipe excess oil from exterior of fork with a towel.  
Step 4 - Pour 30cc of FOX Suspension Fluid into the top of the left upper tube.  
Step 5 - Install travel spacers on top of main spring. Carefully thread Preload Topcap into upper tube and torque to  
165 in-lbs.  
FLOAT Forks - Left Side  
The left leg of FOX FLOAT Forx contains the parts shown on page 12 in the FLOAT Forx Travel Spacer Diagram.  
The following tools and supplies will be needed: 26mm 6-sided socket, 10mm wrench, 2mm hex wrench, 1.5mm hex  
wrench, torque wrench, plastic faced hammer, small screw driver, drain pan, FOX Suspension Fluid plus a FOX High  
Pressure Air Pump and FOX FLOAT Fluid.  
14  
Changing Oil con’t  
Step 1 - Remove the blue air cap from the top of the left fork leg. Let the air out of the fork. Refer to Pump Instructions  
for details about letting the air out with a pump. Remove left top cap with a 26mm socket 6-point socket  
wrench.  
Step 2 - Loosen the bottom nut 3-4 turns with a 10mm wrench. With a plastic mallet, gently tap the bottom of the shaft  
to disengage it from the lower leg. Allow oil to drain into a bucket. Remove the bottom nut and crush washer.  
Step 3 - Compress the fork as much as possible. The air piston will be visible about one inch below the top of the  
upper tube. Push the bottom of the shaft upwards to push the air piston out of the top of the upper tube. If  
necessary, use a small screwdriver to push the bottom of the shaft up through the hole in the bottom of the  
lower leg.  
Step 4 - Pull the air-shaft assembly from the fork. Clean and dry assembly.  
Step 5 - Lubricate the o-ring on the air piston with FOX FLOAT Fluid and re-install the air shaft assembly into the  
upper tube. Push the shaft until it approaches the bottom hole of the fork. Do not push the shaft all the way  
through the bottom hole.  
Step 6 - Turn the fork upside down. Pour 30cc of fresh FOX Suspension Fluid through the bottom hole.  
Step 7 - Push the air shaft assembly up until the shaft comes through the bottom hole. Install the crush washer and  
bottom nut. Torque to 50 in-lbs.  
Step 8 - Turn the fork right side up. Pour 5cc of FOX FLOAT Fluid on top of the air piston.  
Step 9 - Lubricate the o-ring on the air topcap with FOX FLOAT Fluid. Re-install the topcap and torque to 165 in-lbs.  
Step 10 -Air up the fork to the desired pressure and cycle it several times to check for proper operation. Re-install the  
blue air cap.  
FLOAT & Vanilla Forx - Right Side  
The right leg of FOX FORX contains the damper. The damper is a precision component that controls the compression and  
rebound of your FOX FORX. If your cartridge ever loses oil, be sure to complete these 9 steps to ensure that you have the  
proper volume of oil in the damper. Use only FOX Suspension Fluid in your FOX FORX.  
NOTE: Too much oil will cause hydraulic lock-out of the fork. This is a serious condition and could lead to loss  
of control and serious or fatal injury.  
The following tools and supplies will be needed: 26mm 6-sided socket, 10mm wrench, 2mm hex wrench, 1.5mm hex  
wrench, torque wrench, plastic faced hammer, small screw driver, drain pan, FOX Suspension Fluid plus a FOX High  
Pressure Air Pump and FOX FLOAT Fluid.  
Step 1 - Step 1a -On R models, simply remove the right (damper) side top cap with a 26mm 6-sided socket.  
Step 1b -RL and RLC models require that the adjuster knobs be removed as shown on page 14. Remove  
the red rebound knob by firmly holding the red knob from turning and loosen screw with a 2mm hex  
wrench.  
Step 1c -Remove the lock-out lever with a 1.5mm hex wrench by loosening the three set screws and  
carefully lifting the lever. Do not remove the set screws. There are 3 balls in the lockout lever. The 3  
balls are held in place by grease. Do not lose the three balls in the lock-out lever.  
Step 1d -Remove the low-speed compression knob on RLC models. Below the low-speed compression  
knob is a detent ball and spring which sit in a counterbore in the topcap. Check that the ball is  
positioned in the hole by pressing on it with a small screwdriver and feeling for the force of the  
spring.  
Step 1e -Loosen and unscrew the damper topcap with a 26mm 6-sided socket.  
Step 2 - On RLC models, remove the blue blow-off threshold knob with a 2mm hex key wrench.  
Step 3 - Loosen the right side bottom nut with a 10mm wrench or socket 3-4 full turns. Place a clean drain pan under the  
right leg and tap lightly with a plastic hammer on the nut to loosen the damper from the lower leg. Unscrew and  
remove bottom nut and washer. Push up on the shaft and let the oil drain.  
15  
Changing Oil con’t  
Step 4 - Carefully pull the damper from the fork. It will still contain oil.  
Step 5 - Place the damper upright in a deep bucket and carefully cycle the shaft up and down several times to pump out  
the remaining oil. Gently shake the damper to check whether it is empty.  
Step 6 - When the damper is empty, pull it to its maximum length and install it into the fork. Install the crush washer and  
bottom nut and torque to 50 in-lbs.  
Step 7 - Measure 160cc of fresh FOX Suspension Fluid and pour it into the right fork leg. Add it slowly to avoid  
overflowing and spillage.  
Step 8 - Push down on the damper topcap and thread it carefully into the upper tube. Torque to 165 in-lbs.  
Step 9 - Step 9a -Re-install adjuster knobs. On RLC models, install the low speed compression knob so that the  
groove on the bottom is positioned over the aluminum pin in the topcap.  
Step 9b -On RL and RLC models, install the lockout lever onto the hex and rotate clockwise until it stops. It  
may take multiple rotations to seat the lockout shaft. Orient the lever so the lockout tab faces  
approximately the six o’clock position. While pressing the lockout lever down, lightly tighten the  
three set screws. Back each screw off 1/4 turn.  
Step 9c -On all models, install red rebound knob so that the slot feature on the bottom is aligned with the  
flats on the center of the rebound shaft. Apply blue loctite to screw and tighten with 2mm hex  
wrench while holding red rebound knob from spinning.  
Warning - Damper internals will be damaged if the rebound knob is not held turning while the  
screw is tightened.  
Step 10 - Cycle the fork several times and run the adjusters through their full ranges of adjustment. You should feel  
damper fill with oil after several cycles. Adjust all damper settings to your preferences and head out for a  
nice ride.  
Seals and Foam Rings  
FOX FORX feature a sealing system designed to keep your fork moving smoothly in all conditions. There are two parts to the  
system - the fork seal and the foam ring. The fork seal features a proprietary scraper lip geometry that keeps dirt out and oil  
in the fork. The foam ring sits just below the fork seal. It is saturated with oil and in turn applies oil to the upper tube as it  
passes by. This keeps the fork moving up and down smoothly. While FOX FORX are designed to require minimal mainte-  
nance, periodic inspection and cleaning of the fork sealing system is recommended.  
Step 1 - Around the perimeter of the fork seals are small notches. Use a small flat blade screw driver in these slots  
to gently pry the seal from the lower legs of the fork. Once loose, raise them all the way up to the crown on  
the upper tubes.  
Step 2 - Wrap a clean rag around the junction of the upper tubes and the lower legs. This will keep dirt out while the  
seals are being cleaned.  
Step 3 - Use a rag to wipe around the outside diameter of the seal. Wipe until clean.  
Step 4 - Remove the rags and check the foam rings which will be visible just inside the lower legs. They should be  
soaked with oil and should not contain any dirt or debris. If the foam rings are dry, use a few cc’s of FOX  
Suspension Fluid to saturate them.  
Step 5 - Wipe the upper tubes and slide the seals down into the lower legs. Carefully press the seals into place. A  
thin flat bladed screw driver can be used to press in between the upper tube and the fork brace. It is  
recommended that the blade of the screw driver be covered with tape or a rag to prevent damage to the seal.  
Inspect that seal is firmly seated against top surface of the lower leg.  
Step 6 - Wipe off any excess oil and cycle the fork a few times to check for proper operation.  
p/n: 605-00-003-A  
16  
2001 FOX Racing Shox, Inc., FOX Forx Owner’s Manual. The information herein is provided as a guide.  
FOX Racing Shox reserves the right to change all or part without notice.  

Mitel Answering Machine 3300 User Manual
Mitsubishi Motors Automobile Parts 6a1 User Manual
Samsung Am18b1c09 User Manual
Samsung Avmwh040ca0 User Manual
Soleus Air Lx 140 User Manual
T Tech 12 Volt Power Supply Jump Starter Jncxfe User Manual
Whirlpool Acxo82xzo User Manual
Woodstock W1690 User Manual
Xantrex Technology Tc10 User Manual
York Y34 User Manual