FILE NO. SVM-03008
SERVICE MANUAL
AIR CONDITIONER
SPLIT WALL TYPE
RAS-13UKV-E2 / RAS-13UAV-E2
Jun., 2003
FILE NO. SVM-03008
10. HOW TO DIAGNOSE THE TROUBLE
10-1 First Confirmation
10-2 Primary Judgment
10-3 Judgment by Flashing LED of Indoor Unit
10-4 Self-Diagnosis by Remote Control (Check Code)
10-5 Judgment of Trouble by Every Symptom
10-6 Check Code 1C (Miswiring in indoor/outdoor units) and 1E
10-7 How to Diagnose Trouble in Outdoor Unit
10-8 How to Check Simply the Main Parts
10-9 How to Simply Judge Whether Outdoor Fan Motor is Good or Bad
11. HOW TO REPLACE THE MAIN PARTS
11-1 Indoor Unit
11-2 Microcomputer
11-3 Outdoor Unit
12. EXPLODED VIEWS AND PARTS LIST
12-1 Indoor Unit (E-Parts Assy)
12-2 Indoor Unit
12-3 Outdoor Unit
12-4 Outdoor Unit (E-Parts Assy)
– 2 –
FILE NO. SVM-03008
1. SPECIFICATIONS
1-1. Specifications
Unit model
Indoor
RAS-13UKV-E2
Outdoor
RAS-13UAV-E2
Current limited
Cooling capacity
Cooling capacity range
Heating capacity
Heating capacity range
Power supply
—
3.5
0.9 – 4.0
4.2
0.9 – 6.0
(kW)
(kW)
(kW)
(kW)
220 – 240V –1Ph –50/60Hz
Electric
characteristics
Indoor
Operation mode
Cooling
0.15
30
Heating
0.15
30
Running current
Power consumption
Power factor
(A)
(W)
(%)
87
87
Outdoor
Operation mode
Running current
Power consumption
Power factor
Cooling
4.65
1020
95
Heating
5.01
1100
95
(A)
(W)
(%)
(A)
Starting current
5.31
COP (Cooling / Heating)
Operation noise
3.33/3.72
39/39
33/34
26/28
Indoor
High
(Cooling / Heating)
(dB•A)
(dB•A)
(dB•A)
(dB•A)
Medium (Cooling / Heating)
Low
(Cooling / Heating)
(Cooling / Heating)
Outdoor
48/50
Indoor unit
Unit model
Dimension
RAS-13UKV-E2
Height
Width
Depth
(mm)
(mm)
(mm)
(kg)
275
790
208
10
Net weight
Fan motor output
Air flow rate
Unit model
(W)
(m3/h)
30
530/620
RAS-13UAV-E2
(Cooling / Heating)
Outdoor unit
Dimension
Height
Width
Depth
(mm)
(mm)
(mm)
(kg)
550
780
720
40
Net weight
Compressor
Motor output
Type
(W)
750
Twin rotary type with DC-inverter variable speed control
Model
DA91A1F-45F
Fan motor output
Air flow rate
Type
(W)
(m3/h)
43
(Cooling / Heating)
2410/2410
Flare connection
Piping connection
Indoor unit
Liquid side
Gas side
∅6.35
∅9.52
Outdoor unit
Liquid side
Gas side
∅6.35
∅9.52
Maximum length (Per unit)
Maximum chargeless length
Maximum height difference
Name of refrigerant
Weight
(m)
(m)
(m)
15
15
10
R410A
Refrigerant
(kg)
0.9
Wiring connection
Power supply
3 Wires: includes earth (Outdoor)
Interconnection
4 Wires: includes earth
Usable temperature range
Indoor
(Cooling / Heating)
(°C)
21 – 32 / 0 – 28
Outdoor (Cooling / Heating)
Installation plate
Wireless remote control
Remote controller holder
Flat head wood screw
Purifying filter
(°C)
10 – 43 / –10 – 24
Accessory
Indoor unit
1
1
1
2 (∅3.1 x 16L)
1
Zeolite filter
1
Batteries
2
Mounting screw
Installation manual
Owner’s manual
Drain nipple
6 (∅4 x 25L)
1
1
1
Outdoor unit
• The specification may be subject to change without nitice for purpose of improvement.
– 3 –
FILE NO. SVM-03008
1-2. Operation Characteristic Curve
<Cooling>
<Heating>
7
6
5
4
3
7
6
5
4
3
2
1
2
• Conditions
• Conditions
Indoor : DB 27°C/WB 19°C
Indoor : DB 20°C
Outdoor : DB 7°C/WB 6°C
Air flow : High
Outdoor : DB 35°C
Air flow : High
Pipe length : 5m
230V
1
0
Pipe length : 5m
230V
0
0
0
20
40
60
80
100
20
40
60
80
100
Compressor speed (rps)
Compressor speed (rps)
1-3. Capacity Variation Ratio According to Temperature
<Cooling>
<Heating>
120
110
100
90
80
70
60
50
40
30
20
10
0
105
100
95
90
85
80
75
70
65
60
55
50
Current Limited Start
• Conditions
• Conditions
Indoor : DB27°C/WB19°C
Indoor air flow : High
Pipe length 5m
Indoor : DB 20°C
Indoor air flow : High
Pipe length : 5m
−10
−9
−8
−7
−6
−5
−4
−3
−2
−1
0 1 2 3 4 5 6 7 8 9 10
32 33 34 35 36 37 38 39 40 41 42 43
Outdoor temp. (°C)
Outdoor temp. (°C)
Capacity ratio : 100% = 3.5 kW
*
– 4 –
FILE NO. SVM-03008
2. REFRIGERANT R410A
This air conditioner adopts the new refrigerant HFC
(R410A) which does not damage the ozone layer.
(5) After completion of installation work, check to
make sure that there is no refrigeration gas
leakage.
The working pressure of the new refrigerant R410A is
1.6 times higher than conventional refrigerant (R22).
The refrigerating oil is also changed in accordance
with change of refrigerant, so be careful that water,
If the refrigerant gas leaks into the room, coming
into contact with fire in the fan-driven heater,
space heater, etc., a poisonous gas may occur.
dust, and existing refrigerant or refrigerating oil are not (6) When an air conditioning system charged with a
entered in the refrigerant cycle of the air conditioner
using the new refrigerant during installation work or
servicing time.
large volume of refrigerant is installed in a small
room, it is necessary to exercise care so that,
even when refrigerant leaks, its concentration
does not exceed the marginal level.
If the refrigerant gas leakage occurs and its
concentration exceeds the marginal level, an
oxygen starvation accident may result.
The next section describes the precautions for air
conditioner using the new refrigerant. Conforming to
contents of the next section together with the general
cautions included in this manual, perform the correct
and safe work.
(7) Be sure to carry out installation or removal
according to the installation manual.
Improper installation may cause refrigeration
trouble, water leakage, electric shock, fire, etc.
2-1. Safety During Installation/Servicing
As R410A’s pressure is about 1.6 times higher than
that of R22, improper installation/servicing may cause
a serious trouble. By using tools and materials exclu-
sive for R410A, it is necessary to carry out installation/
servicing safely while taking the following precautions
into consideration.
(8) Unauthorized modifications to the air conditioner
may be dangerous. If a breakdown occurs please
call a qualified air conditioner technician or
electrician.
Improper repair’s may result in water leakage,
electric shock and fire, etc.
(1) Never use refrigerant other than R410A in an air
conditioner which is designed to operate with
R410A.
2-2. Refrigerant Piping Installation
If other refrigerant than R410A is mixed, pressure 2-2-1. Piping materials and joints used
in the refrigeration cycle becomes abnormally
For the refrigerant piping installation, copper pipes and
high, and it may cause personal injury, etc. by a
joints are mainly used. Copper pipes and joints suit-
rupture.
able for the refrigerant must be chosen and installed.
(2) Confirm the used refrigerant name, and use tools
and materials exclusive for the refrigerant R410A.
The refrigerant name R410A is indicated on the
visible place of the outdoor unit of the air condi-
tioner using R410A as refrigerant. To prevent
mischarging, the diameter of the service port
differs from that of R22
Furthermore, it is necessary to use clean copper pipes
and joints whose interior surfaces are less affected by
contaminants.
(1) Copper Pipes
It is necessary to use seamless copper pipes
which are made of either copper or copper alloy
and it is desirable that the amount of residual oil is
less than 40 mg/10 m. Do not use copper pipes
having a collapsed, deformed or discolored
portion (especially on the interior surface).
Otherwise, the expansion valve or capillary tube
may become blocked with contaminants.
As an air conditioner using R410A incurs pressure
higher than when using R22, it is necessary to
choose adequate materials.
(3) If a refrigeration gas leakage occurs during instal-
lation/servicing, be sure to ventilate fully.
If the refrigerant gas comes into contact with fire,
a poisonous gas may occur.
(4) When installing or removing an air conditioner,
do not allow air or moisture to remain in the
refrigeration cycle. Otherwise, pressure in the
refrigeration cycle may become abnormally high
so that a rupture of personal injury may be
caused.
Thicknesses of copper pipes used with R410A are
as shown in Table 2-2-1. Never use copper pipes
thinner than 0.8 mm even when it is available on
the market.
– 5 –
FILE NO. SVM-03008
Table 2-2-1 Thicknesses of annealed copper pipes
Thickness (mm)
Nominal diameter
Outer diameter (mm)
R410A
0.80
R22
0.80
0.80
0.80
1.00
1/4
3/8
1/2
5/8
6.35
9.52
0.80
12.70
15.88
0.80
1.00
(2) Joints
b) Socket Joints
For copper pipes, flare joints or socket joints are
used. Prior to use, be sure to remove all
contaminants.
Socket joints are such that they are brazed for
connections, and used mainly for thick pipings
whose diameter is larger than 20 mm.
Thicknesses of socket joints are as shown in
Table 2-2-2.
a) Flare Joints
Flare joints used to connect the copper pipes
cannot be used for pipings whose outer
diameter exceeds 20 mm. In such a case,
socket joints can be used.
Sizes of flare pipe ends, flare joint ends and
flare nuts are as shown in Tables 2-2-3 to 2-2-6
below.
Table 2-2-2 Minimum thicknesses of socket joints
Reference outer diameter of
Minimum joint thickness
(mm)
Nominal diameter
copper pipe jointed (mm)
1/4
3/8
1/2
5/8
6.35
9.52
0.50
0.60
0.70
0.80
12.70
15.88
2-2-2. Processing of piping materials
d) Flare Processing
Make certain that a clamp bar and copper pipe
have been cleaned.
By means of the clamp bar, perform the flare
processing correctly.
Use either a flare tool for R410A or
conventional flare tool.
Flare processing dimensions differ according to
the type of flare tool. When using a
conventional flare tool, be sure to secure
“dimension A” by using a gauge for size
adjustment.
When performing the refrigerant piping installation,
care should be taken to ensure that water or dust does
not enter the pipe interior, that no other oil other than
lubricating oils used in the installed air conditioner is
used, and that refrigerant does not leak. When using
lubricating oils in the piping processing, use such
lubricating oils whose water content has been removed.
When stored, be sure to seal the container with an
airtight cap or any other cover.
(1) Flare Processing Procedures and Precautions
a) Cutting the Pipe
∅D
By means of a pipe cutter, slowly cut the pipe
so that it is not deformed.
A
b) Removing Burrs and Chips
If the flared section has chips or burrs,
refrigerant leakage may occur. Carefully
remove all burrs and clean the cut surface
before installation.
c) Insertion of Flare Nut
Fig. 2-2-1 Flare processing dimensions
– 6 –
FILE NO. SVM-03008
Table 2-2-3 Dimensions related to flare processing for R410A
A (mm)
Conventional flare tool
Outer
diameter
(mm)
Nominal
diameter
Thickness
(mm)
Flare tool for R410A
clutch type
Clutch type
1.0 to 1.5
1.0 to 1.5
1.0 to 1.5
1.0 to 1.5
Wing nut type
1.5 to 2.0
1/4
3/8
1/2
5/8
6.35
9.52
0.8
0.8
0.8
1.0
0 to 0.5
0 to 0.5
0 to 0.5
0 to 0.5
1.5 to 2.0
12.70
15.88
2.0 to 2.5
2.0 to 2.5
Table 2-2-4 Dimensions related to flare processing for R22
A (mm)
Outer
diameter
(mm)
Nominal
diameter
Thickness
(mm)
Conventional flare tool
Flare tool for R410A
clutch type
Clutch type
0.5 to 1.0
0.5 to 1.0
0.5 to 1.0
0.5 to 1.0
Wing nut type
1.0 to 1.5
1/4
3/8
1/2
5/8
6.35
9.52
0.8
0.8
0.8
1.0
0 to 0.5
0 to 0.5
0 to 0.5
0 to 0.5
1.0 to 1.5
12.70
15.88
1.0 to 2.0
1.0 to 2.0
Table 2-2-5 Flare and flare nut dimensions for R410A
Outer
diameter
(mm)
Flare nut
width
(mm)
Dimension (mm)
Thickness
Nominal
diameter
(mm)
A
B
C
D
1/4
3/8
1/2
5/8
6.35
9.52
0.8
0.8
0.8
1.0
9.1
9.2
6.5
13
20
23
25
17
22
26
29
13.2
16.6
19.7
13.5
16.0
19.0
9.7
12.70
15.88
12.9
16.0
Table 2-2-6 Flare and flare nut dimensions for R22
Outer
diameter
(mm)
Flare nut
width
(mm)
Dimension (mm)
Thickness
Nominal
diameter
(mm)
A
B
C
D
1/4
3/8
1/2
5/8
3/4
6.35
9.52
0.8
0.8
0.8
1.0
1.0
9.0
9.2
6.5
13
20
20
23
34
17
22
24
27
36
13.0
16.2
19.7
23.3
13.5
16.0
19.0
24.0
9.7
12.70
15.88
19.05
12.9
16.0
19.2
– 7 –
FILE NO. SVM-03008
Fig. 2-2-2 Relations between flare nut and flare seal surface
(2) Flare Connecting Procedures and Precautions
a) Make sure that the flare and union portions do
not have any scar or dust, etc.
When it is strong, the flare nut may crack and
may be made non-removable. When choosing
the tightening torque, comply with values
designated by manufacturers. Table 2-2-7
shows reference values.
b) Correctly align the processed flare surface with
the union axis.
Note:
c) Tighten the flare with designated torque by
means of a torque wrench. The tightening
torque for R410A is the same as that for
conventional R22. Incidentally, when the torque
is weak, the gas leakage may occur.
When applying oil to the flare surface, be sure to use
oil designated by the manufacturer. If any other oil is
used, the lubricating oils may deteriorate and cause
the compressor to burn out.
Table 2-2-7 Tightening torque of flare for R410A [Reference values]
Tightening torque of torque
wrenches available on the market
N·m (kgf·m)
Nominal
diameter
Outer diameter
(mm)
Tightening torque
N·m (kgf·cm)
1/4
3/8
1/2
5/8
6.35
9.52
14 to 18 (140 to 180)
33 to 42 (330 to 420)
50 to 62 (500 to 620)
63 to 77 (630 to 770)
16 (160), 18 (180)
42 (420)
12.70
15.88
55 (550)
65 (650)
– 8 –
FILE NO. SVM-03008
2-3.Tools
2-3-1. Required tools
The service port diameter of packed valve of the outdoor unit in the air conditioner using R410A is changed to
prevent mixing of other refrigerant. To reinforce the pressure-resisting strength, flare processing dimensions and
opposite side dimension of flare nut (For ∅12.70 copper pipe) of the refrigerant piping are lengthened.
The used refrigerating oil is changed, and mixing of oil may cause a trouble such as generation of sludge,
clogging of capillary, etc. Accordingly, the tools to be used are classified into the following three types.
(1) Tools exclusive for R410A (Those which cannot be used for conventional refrigerant (R22))
(2) Tools exclusive for R410A, but can be also used for conventional refrigerant (R22)
(3) Tools commonly used for R410A and for conventional refrigerant (R22)
The table below shows the tools exclusive for R410A and their interchangeability.
Tools exclusive for R410A (The following tools for R410A are required.)
Tools whose specifications are changed for R410A and their interchangeability
R410A air conditioner
installation
Conventional air
conditioner installation
No.
Used tool
Usage
Existence of
new equipment conventional
Whether
Whether new equipment
can be used with
for R410A
equipment can
be used
conventional refrigerant
1
2
Flare tool
Copper pipe gauge
Pipe flaring
Flaring by
Yes
*(Note 1)
for adjusting projection conventional flare
Yes
*(Note 1)
*(Note 1)
margin
tool
3
4
Torque wrench
(For ∅12.70)
Connection of
flare nut
Yes
Yes
Evacuating,
refrigerant charge,
run check, etc.
Gauge manifold
Charge hose
5
6
Vacuum pump adapter Vacuum evacuating
Yes
Yes
Electronic balance for
Refrigerant charge
refrigerant charging
7
8
9
!
Refrigerant cylinder
Leakage detector
Charging cylinder
Refrigerant charge
Gas leakage check
Refrigerant charge
Yes
Yes
(Note 2)
(Note 1) When flaring is carried out for R410A using the conventional flare tools, adjustment of projection
margin is necessary. For this adjustment, a copper pipe gauge, etc. are necessary.
(Note 2) Charging cylinder for R410A is being currently developed.
General tools (Conventional tools can be used.)
In addition to the above exclusive tools, the following equipments which serve also for R22 are necessary as
the general tools.
(1) Vacuum pump
(4) Reamer
(5) Pipe bender
(9) Hole core drill (∅65)
(10) Hexagon wrench
(Opposite side 5 mm)
(11) Tape measure
(12) Metal saw
Use vacuum pump by
attaching vacuum pump adapter. (6) Level vial
(2) Torque wrench (For ∅6.35)
(3) Pipe cutter
(7) Screwdriver (+, –)
(8) Spanner of Monkey wrench
Also prepare the following equipments for other installation method and run check.
(1) Clamp meter
(2) Thermometer
(3) Insulation resistance tester
(4) Electroscope
– 9 –
FILE NO. SVM-03008
2-4. Recharging of Refrigerant
When it is necessary to recharge refrigerant, charge the specified amount of new refrigerant according to the
following steps.
Recover the refrigerant, and check no refrigerant
remains in the equipment.
When the compound gauge’s pointer has indi-
cated -0.1 Mpa (-76 cmHg), place the handle Low
in the fully closed position, and turn off the
Connect the charge hose to packed valve service
port at the outdoor unit’s gas side.
vacuum pump’s power switch.
Keep the status as it is for 1 to 2 minutes, and
ensure that the compound gauge’s pointer does
not return.
Connect the charge hose to the vacuum pump
adapter.
Open fully both packed valves at liquid and gas
Set the refrigerant cylinder to the electronic
sides.
balance, connect the connecting hose to the
cylinder and the connecting port of the electronic
balance, and charge liquid refrigerant.
Place the handle of the gauge manifold Low in
the fully opened position, and turn on the vacuum
pump’s power switch. Then, evacuating the
refrigerant in the cycle.
(For refrigerant charging, see the figure below.)
1 Never charge refrigerant exceeding the specified amount.
2 If the specified amount of refrigerant cannot be charged, charge refrigerant bit by bit in COOL mode.
3 Do not carry out additional charging.
When additional charging is carried out if refrigerant leaks, the refrigerant composition changes in the
refrigeration cycle, that is characteristics of the air conditioner changes, refrigerant exceeding the
specified amount is charged, and working pressure in the refrigeration cycle becomes abnormally high
pressure, and may cause a rupture or personal injury.
(Liquid side)
(INDOOR unit)
(OUTDOOR unit)
Opened
Closed
(Gas side)
Refrigerant cylinder
(With siphon pipe)
Check valve
Open/Close valve
for charging
Service port
Electronic balance for refrigerant charging
Fig. 2-4-1 Configuration of refrigerant charging
– 10 –
FILE NO. SVM-03008
1 Be sure to make setting so that liquid can be charged.
2 When using a cylinder equipped with a siphon, liquid can be charged without turning it upside down.
It is necessary for charging refrigerant under condition of liquid because R410A is mixed type of refrigerant.
Accordingly, when charging refrigerant from the refrigerant cylinder to the equipment, charge it turning the
cylinder upside down if cylinder is not equipped with siphon.
[Cylinder with siphon]
[Cylinder without siphon]
Gauge manifold
Gauge manifold
OUTDOOR unit
OUTDOOR unit
Refrigerant
cylinder
Refrigerant
cylinder
Electronic
balance
Electronic
balance
Siphon
R410A refrigerant is HFC mixed refrigerant.
Therefore, if it is charged with gas, the composition
of the charged refrigerant changes and the
characteristics of the equipment varies.
Fig. 2-4-2
2-5. Brazing of Pipes
1 Phosphor bronze brazing filler tends to react
with sulfur and produce a fragile compound
water solution, which may cause a gas leakage.
Therefore, use any other type of brazing filler at
a hot spring resort, etc., and coat the surface
with a paint.
2-5-1. Materials for brazing
(1) Silver brazing filler
Silver brazing filler is an alloy mainly composed of
silver and copper. It is used to join iron, copper or
copper alloy, and is relatively expensive though it
excels in solderability.
2 When performing brazing again at time of
servicing, use the same type of brazing filler.
(2) Phosphor bronze brazing filler
Phosphor bronze brazing filler is generally used to
join copper or copper alloy.
2-5-2. Flux
(1) Reason why flux is necessary
(3) Low temperature brazing filler
Low temperature brazing filler is generally called
solder, and is an alloy of tin and lead. Since it is
weak in adhesive strength, do not use it for
refrigerant pipes.
•
By removing the oxide film and any foreign
matter on the metal surface, it assists the flow
of brazing filler.
•
•
In the brazing process, it prevents the metal
surface from being oxidized.
By reducing the brazing filler’s surface tension,
the brazing filler adheres better to the treated
metal.
– 11 –
FILE NO. SVM-03008
(2) Characteristics required for flux
2-5-3. Brazing
•
Activated temperature of flux coincides with the
brazing temperature.
Due to a wide effective temperature range, flux
is hard to carbonize.
It is easy to remove slag after brazing.
The corrosive action to the treated metal and
brazing filler is minimum.
As brazing work requires sophisticated techniques,
experiences based upon a theoretical knowledge, it
must be performed by a person qualified.
In order to prevent the oxide film from occurring in the
pipe interior during brazing, it is effective to proceed
with brazing while letting dry Nitrogen gas (N2) flow.
•
•
•
•
It excels in coating performance and is
harmless to the human body.
Never use gas other than Nitrogen gas.
(1) Brazing method to prevent oxidation
1 Attach a reducing valve and a flow-meter to the
Nitrogen gas cylinder.
As the flux works in a complicated manner as
described above, it is necessary to select an
adequate type of flux according to the type and
shape of treated metal, type of brazing filler and
brazing method, etc.
2 Use a copper pipe to direct the piping material,
and attach a flow-meter to the cylinder.
3 Apply a seal into the clearance between the
piping material and inserted copper pipe for
Nitrogen in order to prevent backflow of the
Nitrogen gas.
(3) Types of flux
•
Noncorrosive flux
Generally, it is a compound of borax and boric
acid.
4 When the Nitrogen gas is flowing, be sure to
keep the piping end open.
It is effective in case where the brazing
temperature is higher than 800°C.
5 Adjust the flow rate of Nitrogen gas so that it is
lower than 0.05 m3/Hr or 0.02 Mpa (0.2 kgf/
cm2) by means of the reducing valve.
6 After performing the steps above, keep the
Nitrogen gas flowing until the pipe cools down
to a certain extent (temperature at which pipes
are touchable with hands).
•
Activated flux
Most of fluxes generally used for silver brazing
are this type.
It features an increased oxide film removing
capability due to the addition of compounds
such as potassium fluoride, potassium chloride
and sodium fluoride to the borax-boric acid
compound.
7 Remove the flux completely after brazing.
(4) Piping materials for brazing and used brazing
filler/flux
M
Flow meter
Piping
material
Used brazing
filler
Used
flux
Stop valve
Copper - Copper Phosphor copper
Do not use
Paste flux
Vapor flux
Nitrogen gas
cylinder
Copper - Iron
Iron - Iron
Silver
Silver
From Nitrogen cylinder
1 Do not enter flux into the refrigeration cycle.
2 When chlorine contained in the flux remains
within the pipe, the lubricating oil deteriorates.
Therefore, use a flux which does not contain
chlorine.
3 When adding water to the flux, use water which
does not contain chlorine (e.g. distilled water or
ion-exchange water).
Pipe
Nitrogen
gas
Rubber plug
Fig. 2-5-1 Prevention of oxidation during brazing
4 Remove the flux after brazing.
– 12 –
FILE NO. SVM-03008
3. CONSTRUCTION VIEWS
3-1. Indoor Unit
Front panel
Back body
Air filter
Air inlet
Heat exchanger
208
790
48
Air outlet
Knock out system
Knock out system
64 53
120
590
Hanger
80
Connecting pipe (0.43m)
(Flare ∅6.35)
Connecting pipe (0.33m)
Drain hose (0.54m)
Hanger
320
Flare ∅9.52
620
For stud bolt
(∅8~∅10)
235
215
235
215
For stud bolt (∅6)
Minimum
distance
to ceiling
Hanger
Minimum
distance
to ceiling
Minimum
distance
to ceiling
170 or more
170 or more
Hanger
150
57
18
Hanger
Wireless remote control
90
150
160
160
90
Installation plate outline
Center line
– 13 –
FILE NO. SVM-03008
3-2. Outdoor Unit
A
32.5
A Detail drawing (Back Leg)
115
125
B Detail drawing (Front Leg)
600
52
36
∅6 Hole
R15
∅6 Hole
∅11 x 14 Hole
36
52
R15
R5.5
B
∅30 Drain outlet
2-∅11 x 14 Hole
(For ∅8-∅10 anchor bolt)
FAN GUARD
∅436
COVER PV
Z
270
310
330
600
780
90
62
Electrical
part cover
Liquid side
(Flare ∅6.35)
Gas side
(Flare ∅9.52)
Z View
Service port
Installation dimension
600
Air inlet
600 or more
600 or more
Air outlet
600 or more
100 or more
4 x ∅11 x 14 Long holes (For ∅8 − ∅10 anchorbolt)
– 14 –
FILE NO. SVM-03008
4. WIRING DIAGRAM
4-1. Indoor Unit
Table 4-1-1 Simple Check for Failure Diagnosis
Diagnosis Result
Check Item
Check to see if the OPERATION indicator goes on and off when the main
switch or breaker is turned on.
(Check the primary and secondary voltage of the transformer.)
OPERATION
1
INDICATOR
Check the power supply voltage between 1 and 2. (Refer to the name plate.)
(Check the primary and secondary voltage of the transformer.)
Check the fluctuating voltage between 2 and 3. (DC15 to 60 V)
TERMINAL BLOCK
2
Check to see if the fuse blows out.
(Check the R04 of the varistor.)
FUSE 3.15A
DC5V
3
4
5
6
Check the voltage at the No. 4 pin on CN13 connector of the infrared receiver.
(Check the transformer and the power supply circuit of the rated voltage.)
Check the voltage at the white lead of the louver motor.
(Check the transformer and the power supply circuit of the rated voltage.)
DC12V
DC325V
(DC310 to 340V)
Check the voltage at the No. 1 pin on CN10 connector.
(Check the DB01, R05 and C03.)
Refer to the service data for the detailed failure diagnosis.
– 15 –
FILE NO. SVM-03008
4-2.Outdoor Unit
P.C. BOARD
(MCC-813)
– 16 –
FILE NO. SVM-03008
5. SPECIFICATION OF ELECTRICAL PARTS
5-1. Indoor Unit
No.
1
Parts name
Type
ICF-340-30-2
———
Specifications
DC 340 V, 30 W
Fan motor (for indoor)
Thermo. sensor (TA-sensor)
DC-DC transformer (T01)
Microcomputer
2
10 kΩ at 25°C
3
SWT-70
DC 390 V, Secondary DC 15 V, 12 V, 7 V
4
µPD780024AGK
5
Heat exchanger sensor
(TC-sensor)
———
10 kΩ at 25°C
6
7
Line filter (L01
SS11V-06270
D3SBA60
27mH, AC 0.6A
4A, 600 V
Diode (DB01)
8
Capacitor (C03)
Fuse (F01)
KMH450VNSN120M25C 120µF, 450 V
9
FCU250V, 3.15A
STR-L472
T3.15A, 250 V
10
11
12
Power supply IC (IC01)
Varistor (R21, R109)
Resistor (R01)
15G561K
560 V
RF-5TK4R7
4.7Ω, 5 W
Output (Rated) 1 W,16 poles, 1 phase,
DC 12 V
13
Louver motor
MP24GA
5-2. Outdoor Unit
No.
Parts name
Model name
ADR2516-0R6TB
ADR2520-R15TB
Rating
20A, 150µH
1
SC coil
L01
L03
(Noise filter)
15A, 0.6mH
Primary side DC280V, Secondary
side 7.5 V x 1, 13 V x 1, 26.5V x 3,
16 V x 1, 15 V x 1
2
DC-DC transformer
SWT-43
3
4
5
Reactor
CH-57-Z-T
L=10mH, 16A x 2
DC140 V, 43 W
Outside fan motor
ICF-140-43-1
Suction temp. sensor
(TS sensor)
(Inverter attached)
(Inverter attached)
(Inverter attached)
10 kΩ (25°C)
62 kΩ (20°C)
10 kΩ (25°C)
Discharge temp. sensor
(TD sensor)
6
7
Outside air temp. sensor
(TO sensor)
Heat exchanger temp.
sensor (TE sensor)
8
9
(Inverter attached)
———
10 kΩ (25°C)
Terminal block (6P)
20A, AC 250 V
For protection of switching power source
3.15A, AC 250 V
10
Fuse
For protection of inverter input overcurrent 25A, AC 250 V
11
12
13
14
Electrolytic capacitor
Transistor module
Compressor
LLQ2G501KHUATF, 400LISN500K35F
500µF, DC 400 V x 3 pieces
6MBI25GS-060-01 or 6MBI25GS-060-01A 25A, 600 V
DA91A1F-45F
PW-2AL
3-phases 4-poles 750 W
Compressor thermo.
OFF: 125 ± 4°C, ON: 90 ± 5°C
Diode: 25A, 600 V,
IGBT: 40 A, 600V
15
Converter module
MP7003
– 17 –
FILE NO. SVM-03008
6. REFRIGERANT CYCLE DIAGRAM
6-1. Refrigerant Cycle Diagram
T1 Temp. measurement
INDOOR UNIT
Indoor heat
exchanger
Cross flow fan
P
Pressure measurement
Max. : 15 m
Deoxidized copper pipe
Outer dia. : 6.35 mm
Thickness : 0.8 mm
Gauge attaching port
Vacuum pump connecting port
Sectional shape
of heat insulator
Deoxidized copper pipe
Outer dia. : 9.52 mm
Thickness : 0.8 mm
Strainer
Muffler
4-way valve
(CHV-0213)
Pulse modulating
valve at liquid side
(SEV16RC3)
Muffler
TD
Compressor
DA91A1F-45F
TS
TO
Outdoor heat
exchanger
Split capillary
∅1.5 x 200
s
∅1.5 x 200
s
Temp. measurement
T2
TE
Refrigerant amount : 0.9 kg
Propeller fan
OUTDOOR UNIT
Gas leak check position
Refrigerant flow (Cooling)
Refrigerant flow (Heating)
NOTE :
Note :
•
The maximum length of the pipe for this air conditioner is 15 m. The additional charging of refrigerant is
unnecessary because this air conditioner is designed with charge-less specification.
– 18 –
FILE NO. SVM-03008
6-2. Operation Data
<Cooling>
Temperature
condition (°C)
Heat exchanger
pipe temp.
Standard
pressure
P (MPa)
Indoor
fan
mode
Outdoor Compressor
Model
name
fan
revolution
(rps)
mode
Indoor
Outdoor
T1 (°C)
T2 (°C)
27/19
35/–
13UKV-E2 0.8 to 1.0
9 to 11
49 to 45
High
High
77
<Heating>
Temperature
condition (°C)
Heat exchanger
pipe temp.
Standard
Model
Indoor
fan
mode
Outdoor Compressor
pressure
name
fan
mode
revolution
(rps)
P (MPa)
Indoor Outdoor
20/– 7/6
T1 (°C)
T2 (°C)
13UKV-E2 2.5 to 2.7 42 to 44
0 to 3
High
High
83
Note :
(1) Measure surface temperature of heat exchanger pipe around center of heat exchanger path U bent.
(Thermistor themometer)
(2) Connecting piping condition : 5m
– 19 –
FILE NO. SVM-03008
7. CONTROL BLOCK DIAGRAM
7-1. Indoor Unit
Indoor Unit Control Panel
M.C.U
Functions
Operation
Display
Heat Exchanger Sensor
•
Louver Control
Timer
Display
Temperature Sensor
•
3-minute Delay at Restart for Compressor
Filter
Sign Display
•
Motor Revolution Control
Infrared Rays Signal Receiver
PRE DEF.
Sign Display
Initiallizing Circuit
Infrared
•
•
Processing
(Temperature Processing)
Rays
Indoor
Fan Motor
Clock Frequency
Timer
36.7KHz
Oscillator Circuit
Louver
Motor
•
Serial Signal Communication
Power Supply
Louver ON/OFF Signal
Circuit
Remote
Control
Louver Motor
Louver Driver
Noise Filter
Serial Signal Transmitter/Receiver
Serial Signal Communication
From Outdoor Unit
REMOTE CONTROL
Infrared Rays
Remote Control
Operation (START/STOP)
Operation Mode Selection
AUTO, COOL, DRY, HEAT, FAN ONLY
Temperature Setting
Fan Speed Selection
ON TIMER Setting
OFF TIMER Setting
Louver Auto Swing
Louver Direction Setting
ECO
Hi power
Filter Reset
– 20 –
FILE NO. SVM-03008
7-2. Outdoor Unit (Inverter Assembly)
– 21 –
FILE NO. SVM-03008
8. OPERATION DESCRIPTION
(1) Role of indoor unit controller
8-1. Outlined of Air Conditioner Control
The indoor unit controller judges the operation
commands from the remote controller and
assumes the following functions.
This air conditioner is a capacity-variable type air
conditioner, which uses DC motor for the indoor fan
motor and the outdoor fan motor. And the capacity
proportional control compressor which can change the
motor speed in the range from 13 to 110 rps is
mounted. The DC motor drive circuit is mounted to the
indoor unit. The compressor and the inverter to control
fan motor are mounted to the outdoor unit.
•
Judgment of suction air temperature of the
indoor heat exchanger by using the indoor
temp. sensor (TA sensor)
•
Temperature setting of the indoor heat
exchanger by using heat exchanger sensor
(TC sensor) (Prevent-freezing control)
Louver motor control
The entire air conditioner is mainly controlled by the
indoor unit controller.
•
•
•
•
Indoor fan motor operation control
The indoor unit controller drives the indoor fan motor
based upon command sent from the remote control,
and transfers the operation command to the outdoor
unit controller.
LED (Light Emitting Diode) display control
Transferring of operation command signal
(Serial signal) to the outdoor unit
•
Reception of information of operation status
(Serial signal including outside temp. data) to
the outdoor unit and judgment/display of error
The outdoor unit controller receives operation
command from the indoor unit side, and controls the
outdoor fan and the pulse modulating valve. (P.M.V)
Besides, detecting revolution position of the
compressor motor, the outdoor unit controller controls
speed of the compressor motor by controlling output
voltage of the inverter and switching timing of the
supply power (current transfer timing) so that motors
drive according to the operation command. And then,
the outdoor unit controller transfers reversely the
operating status information of the outdoor unit to
control the indoor unit controller.
(2) Role of outdoor unit controller
Receiving the operation command signal (Serial
signal) from the indoor controller, the outdoor unit
performs its role.
Operations followed
to judgment of serial
signal from indoor
side.
•
•
Compressor operation
control
Operation control of
outdoor fan motor
P.M.V. control
•
•
Detection of inverter input current and current
release operation
As the compressor adopts four-pole brushless
DC motor, the frequency of the supply power
from inverter to compressor is two-times
cycles of the actual number of revolution.
•
Over-current detection and prevention
operation to IGBT module (Compressor stop
function)
•
Compressor and outdoor fan stop function
when serial signal is off (when the serial signal
does not reach the board assembly of outdoor
control by trouble of the signal system).
Transferring of operation information (Serial
signal) from outdoor unit to indoor unit
Detection of outdoor temperature and
operation revolution control
•
•
•
Defrost control in heating operation (Temp.
measurement by outdoor heat exchanger and
control for 4-way valve and outdoor fan)
– 22 –
FILE NO. SVM-03008
(3) Contents of operation command signal (Serial
signal) from indoor unit controller to outdoor unit
controller
8-1-1. Capacity control
The cooling and heating capacity is varied by changing
compressor motor speed. The inverter changes
compressor motor speed by changing
AC 220-240 V power to DC once, and controls capac-
ity by changing supply power status to the compressor
with transistor module (includes 6 transistors). The
outline of the control is as follows:
The following three types of signals are sent from
the indoor unit controller.
•
•
Operation mode set on the remote control
Compressor revolution command signal
defined by indoor temperature and set tem-
perature (Correction along with variation of
room
The revolution position and revolution speed of the
motor are detected by detecting winding electromotive
force of the compressor motor under operation, and
the revolution speed is changed so that the motor
drives based upon revolution speed of the operation
command by changing timing (current transfer timing)
to exchange inverter output voltage and supply power
winding.
temperature and correction of indoor heat
exchanger temperature are added.)
For these two types of signals ([Operation
mode] and [Compressor revolution]), the
outdoor unit controller monitors the input
current to the inverter, and performs the
followed operation within the range that current
does not exceed the allowable value.
Temperature of indoor heat exchanger by
indoor heat exchanger sensor
•
•
Detection of the revolution position for controlling is
performed 12 times per 1 revolution of compressor.
The range of supply power frequency to the
compressor differs according to the operation status
(COOL, HEAT, DRY).
(Minimum revolution control)
(4) Contents of operation command signal (Serial
signal) from outdoor unit controller to indoor unit
controller
Table 8-1-1 Compressor revolution range
The following signals are sent from the outdoor
unit controller.
Operation
mode
Model
name
Compressor
revolution (rps)
•
•
•
•
The current operation mode
The current compressor revolution
Outdoor temperature
COOL
HEAT
13 to 88
13UKV-E2
16 to 110
Existence of protective circuit operation
For transferring of these signals, the indoor unit
controller monitors the contents of signals, and
judges existence of trouble occurrence.
Contents of judgment are described below.
Whether distinction of the current operation
status meets to the operation command signal
Whether protective circuit operates
8-1-2. Current release control
The outdoor main circuit control section (Inverter
assembly) detects the input current to the outdoor unit.
If the current value with compressor motor speed
instructed from indoor side exceeds the specified
value, the outdoor main circuit control section controls
compressor motor speed by reducing motor speed so
that value becomes closest to the command within the
limited value.
•
•
When no signal is received from the outdoor
unit controller, it is assumed as a trouble.
8-1-3. Power factor improvement control
Power factor improvement control is performed mainly
aiming to reduce the current on much power consump-
tion of cooling/heating operation. Controlling starts
from the time when input power has reached at a
certain point. To be concrete, IGBT of the power factor
improvement circuit is used, and the power factor is
improved by keeping IGBT on for an arbitrary period to
widen electro-angle of the input current.
– 23 –
FILE NO. SVM-03008
8-1-4. Prevent-freezing control
8-1.7. Indoor fan control (DC fan motor)
The indoor heat exchanger sensor detects refrigerant
vapor temperature in COOL/DRY operation. If the
temperature is below the specified value, compressor
motor speed is reduced so that operation is performed
in temperature below the specified value to prevent-
freezing of indoor heat exchanger.
(1) The indoor fan is operated by the stepless speed
change DC motor.
(2) For air flow level, speed of the indoor fan motor is
controlled in five steps (LOW, LOW+, MED, MED+
and HIGH). If AUTO mode is selected, the fan
motor speed is automatically controlled by the
difference between the preset temperature and
the room temperature.
8-1-5. P.M.V. (Pulse Modulating Valve)
Using P.M.V., refrigerant flow of refrigeration cycle is
varied for the optimum temperature.
LOW+MED
LOW+ =
2
After the power has been turned on, when a serial
operation signal is received from indoor at the first
time, or when PMV alarm is detected and the equip-
ment is reactivated, move the valve once until it hits on
the stopper for positioning of the valve. In this case,
ticktack sound may be heard.
MED+HIGH
MED+ =
2
Table 8-1-2
RAS-13UKV-E2
Operation
mode
Fan
mode
Motor speed Air flow rate
8-1-6. Louver control
(rpm)
1210
1010
810
(m3/h)
530
420
330
320
620
470
380
(1) Vertical air flow louvers
H
M
L
Positions of vertical air flow louvers are
automatically controlled according to the operation
status (AUTO (A), COOL ( ), DRY ( ), HEAT( )
and FAN ONLY ( ). Besides, positions of vertical
air flow louvers can be arbitrarily set by pushing
the [FIX] button.
COOL
DRY
—
H
M
L
780
1290
1110
930
(2) Swing
HEAT
If the [SWING] button is pressed during running
operation, vertical air flow louvers start swinging.
When the [FIX] button is pushed, swinging stops.
– 24 –
FILE NO. SVM-03008
8-1-8. Outdoor fan control (DC fan motor)
Although the outdoor fan motor drives the outdoor fan by non-step variable system of the revolution speed, the
revolution speed is restricted to three steps on the convenience of controlling. If a strong wind is lashing outside
of the room, the operation may be continued as the outdoor fan stops in order to protect the outdoor fan motor.
If a fan lock occurred due to entering of foreign matter, the air conditioner stops and an alarm is displayed.
<COOL, DRY>
Table 8-1-3
Model name
RAS-13UAV-E2
Compressor revolution (rps)
To 13.8
390
To 34.7
840
From 35.3
840
TO ≥ 38°C
Outdoor temp. sensor TO
ECONO. operation
TO < 38°C
TO < 15°C
TO ≥ 38°C
TO < 38°C
TO < 15°C
390
700
840
390
390
390
700
840
700
390
390
TO is abnormal
700
700
840
<HEAT>
Table 8-1-4
Model name
Compressor revolution (rps)
RAS-13UAV-E2
To 16.8
390
To 57.4
650
From 58.0
840
TO ≥ 5°C
Outdoor temp. sensor TO
TO < 5°C
TO ≥ 5°C
TO < 5°C
650
650
840
390
390
650
ECONO. operation
TO is abnormal
390
650
650
390
650
840
– 25 –
FILE NO. SVM-03008
(1) Cooling capacity control
8-2. Description of Operation Circuit
•
The cooling capacity and room temperature
are controller by changing the compressor
motor speed according to both the difference
between the temperature detected by the room
temperature sensor and the temperature set by
•
Turning [ON] the breaker flashes the operation
lamp. (1Hz)
This is the display of power-ON (or notification of
power failure).
•
When pushing [START/STOP] button of the
remote control, receive sound is issued from the
main unit, and the next operations are performed
together with opening the vertical air flow louvers.
TEMP
button and also any change in room
temperature.
•
•
When compressor has been activated or
reactivated, it operates with Max.41 rps for 2
minutes, with Max.91 rps from 2 minutes to 3
minutes, and with Max.88 rps after 3 minutes
passed.
When room temperature is lower than set
temperature, indoor fan motor is operated at
fan speed L as shown in Fig. 8-2-1 while the
outdoor unit stops.
8-2-1. Cooling operation
(The Remote Control MODE Button is Set to
the COOL Position)
•
Once the setting is made, the operation mode is
memorized in the microcomputer so that the same
operation can be effected thereafter simply by
pushing [START/STOP] button.
(2) Prevent-freezing control
•
•
A cooling operation signal is transmitted to
outdoor unit.
The outdoor unit controls the outdoor fan relay
R01, R02 and R03, and the compressor motor
speed according to the operation command signal
sent from the indoor unit.
If temperature of indoor heat exchanger detected
by the indoor heat exchanger sensor is 5°C lower,
compressor motor speed is gradually lowered to
prevent freezing of the indoor heat exchanger. If
temperature is 7°C or higher, return the operation
to the above item (1).
•
When [FAN] button is set to AUTO, the indoor fan
motor operates as shown in Fig. 8-2-1. When
(3) Current release control
[FAN] button is set to LOW , LOW+
,
The input current of compressor and outdoor fan
motor (Precisely inverter main circuit control
section) which occupy most of air conditioner input
is detected by the outdoor current sensor, and
compressor motor speed is gradually lowered so
that current value does not exceed 9.0A if current
value exceeds 9.0A. When the current value
lowers to 8.5A, return the operation to the above
item (1).
MED
, MED+
, HIGH
, the
motor operates with a constant air flow.
°C
+3
M+
*1
*1
*1
L
+2.5
+2
+1.5
+1
Comp. motor
speed down
9.0
+0.5
0
Set
temp.
Comp. motor
speed keep
In normal
operation
8.5
−0.5
Normal control
NOTE :
*1: Calculated from difference in motor speed of M+
and L, and controlled.
Fig. 8-2-2
Fig. 8-2-1 Setting of air flow [Fan AUTO]
– 26 –
FILE NO. SVM-03008
(4) Limit for maximum compressor motor speed
by indoor fan speed
6) Control 6 (F zone) : Operation stop zone
If TD detect value exceeds 117°C during
operation, stop the operation immediately.
Then, restart the operation when TD detect
value becomes 105°C or lower.
When outdoor temperature sensor detected 32°C
or lower, and indoor heat exchanger sensor
detected 17°C or lower, the maximum compressor
motor speed is limited by the indoor fan speed.
For example, the compressor motor speed is
limited as described in the table below.
TD
(°C)
Zone
F
E
D
Operation stop zone
117
112
108
Normal down zone
of motor speed
Table 8-2-1
Release of
motor speed
Slow down of
motor speed
RAS-13UKV-E2
Air flow rate
(rps)
HIGH
M+
77
Keep zone :
C
B
Motor speed is not changed.
105
98
65
MED.
L–, L
53
Slow-up zone of motor speed
30
A
Normal operation zone
UL, SUL
30
rps : round per second
Fig. 8-2-3 Compressor motor speed control
(5) Louver control
The vertical air flow louvers are automatically set
to horizontal or cool memory position.
(7) ECO operation control
When the ECO button of the remote control is
pushed, quiet and mild operation is performed by
restraining air flow and operating motor speed.
When temperature of indoor heat exchanger
becomes 5°C or lower by the prevent-freezing
control and the compressor is turned off, the
vertical air flow louvers close once and then return
to the position of previous time.
1) Indoor air flow is controlled between SUL and
L.
2) The set temperature increases 0.5°C per 1
hour up to +2°C starting from the set
temperature when ECO mode has been
received.
(6) Discharge temperature control
(Common control to cooling and heating)
The discharge temperature of refrigerant gas from
the compressor is detected by the discharge
temperature sensor, and controls operating
compressor motor speed.
TA [°C]
rps
40
35
31
27
22
18
13
FAN
L
1) Control 1 (A zone) : Normal operation zone
When TD detect value is 98°C or lower, the
operation is performed with operating motor
speed instructed by the serial signal.
2) Control 2 (B zone) : Slow-up zone of motor
speed
When TD detect value is 98°C or higher,
operating motor speed is slowly up.
3) Control 3 (C zone) : Keep zone
When TD detect value is 105°C or higher,
operating motor speed is not changed if raising
operation speed.
+4.0
+3.5
+3.0
+2.5
+2.0
+1.5
+1.0
+0.5
Tsc
L−
UL
−0.5
−1.0
SUL
4) Control 4 (D zone) : Slow down zone of motor
speed
−2.0
OFF
When TD detect value is 108°C or higher,
operating motor speed is slowly down.
5) Control 5 (E zone) : Normal down of motor
speed
Fig. 8-2-4
When TD detect value is 112°C or higher,
operating motor speed is down.
– 27 –
FILE NO. SVM-03008
8-2-2. DRY operation
(The Remote Control MODE Button is Set to
[Basic control]
the DRY Position)
LOW
Set
temp.
0
−0.5
−1
•
Once the setting is made, the operation mode is
memorized in the microcomputer so that the same
operation can be effected thereafter simply by
pushing [START/STOP] button.
1
*
−1.5
−2
2
*
•
•
Dry operation signal is transmitted to outdoor unit.
The Cooling operation giving priority to
dehumidifying, which restrains the indoor fan speed
and compressor motor speed, is performed.
The indoor fan motor operates as shown in
Fig. 8-2-5. (Fan speed is AUTO only.)
The outdoor fan motor operates as described in
Table 8-1-3, and the compressor motor speed
according to the operation command signal sent
from the indoor unit.
M+
−5.0
−5.5
•
•
HIGH
[FAN AUTO]
*1,*2 : Approximate revolution speed of M+ and L to
linear accordingly to temperature.
Fig. 8-2-6 Setting of air flow
+2.5
[Cold draft preventing control]
+2.0
+1.5
+1.0
+0.5
0
L−
The upper limit of fan revolution speed is shown below.
*1
HIGH
44
43
33
32
SUL
Approximate
revolution speed
of HIGH and SUL
linear by Tc.
31
30
20
19
Set
temp.
3
*
SUL
2
*
A
−0.5
A + 4
( NOTE : 1)
SUL
Stop
*
A − 8 A − 8
NOTE :
Starting
FAN
*1 : Middle motor speed between L– and SUL
of FAN
AUTO
Manual
Fig. 8-2-5 Setting of air flow
Fig. 8-2-7 Cold draft preventing control
NOTES :
*1 : Stops for 2 minutes after thermostat-OFF.
*2 : 24°C when the set temp. is 24°C or more
Set temp. when the set temp. is below 24°C
*3 : SUL : Super ultra low
8-2-3. Heating operation
Transferring of heat operation signal from indoor unit to
outdoor unit starts.
The indoor fan motor operates by the room
temperature when selecting “AUTO” of “FAN” as shown
in Fig. 8-2-6, and operates with a set air flow when
selecting “LOW ” to “HIGH
”.
However, to prevent cold draft, revolution speed of the
fan is restricted by indoor heat exchanger when air
flow is AUTO (Fig. 8-2-7) and starting of FAN Manual.
– 28 –
FILE NO. SVM-03008
[In starting and in stability]
In starting
TO
In stability
9.8A
10.3A
10.8A
16.0
15.5
11.0
10.5
• Until 12 minutes
passed after
operation start
• When 12 to 25
• When 12 to 25
minutes passed
after operation
start and room
temp. is higher
than (set temp.
–3°C)
minutes passed
FAN
after operation
AUTO
start and room
Fig. 8-2-8
temp. is 3°C or
lower than set
temp.
• When 25 minutes
or more passed
after operation
start
(4) Defrost control
1) Detection of frost
In heating operation, time duration while the
compressor operates is counted, and defrost
operation starts by any condition described
below.
FAN
Manual
• Room temp. < Set • Room temp.
temp. –4°C
Set temp. –3.5°C
The outdoor unit controls the outdoor fan based upon
the operation signal sent from the indoor unit, and also
controls revolution speed of the compressor motor.
a. The counted time is 28 minutes or more,
and status that temperature of the outdoor
heat exchanger detected by the outdoor
heat exchanger is –20°C or lower continued
for 2 minutes or more.
The power coupler (IC20) for 4-way valve is turned on,
and turned off in defrost operation.
b. The counted time is 28 minutes or more,
and status that temperature of the outdoor
heat exchanger detected by the outdoor
heat exchanger is –7°C or lower and
temperature lowered by 2.5°C than the
minimum value of the outdoor heat
(1) Heating capacity control
Calculate the difference between temperature
detected by room temp. sensor every minute and
the set temp. set on “Temp. indicator” and variation
amount of room temp.
exchanger during 10 to 15 minutes count
time continued for 2 minutes or more.
c. The counted time is 34 minutes or more,
and status that temperature of the outdoor
heat exchanger detected by the outdoor
heat exchanger is -5°C or lower and
temperature lowered by 3.0°C than the
minimum value of the outdoor heat
exchanger during 10 to 15 minutes count
time continued for 2 minutes or more.
d. If the following three conditions are satis-
fied, defrost operation (Timer defrost) starts
after heating operation for 37 minutes.
1 Setting on remote control, HEAT
Then, obtain the correction amount of the com-
mand signal, and correct the current frequency
command signal.
(2) High-temp. release control
If temperature of the indoor heat exchanger
detected by the indoor heat exchanger sensor is
55°C or higher, compressor motor speed is
gradually lowered to prevent over-temp. rising of
compressed pressure.
If temperature becomes below 48°C, return to
above item (1).
(3) Current release control
The input current of compressor and outdoor fan
motor (Precisely inverter main circuit control
section) which occupies most of air conditioner
input is detected by the outdoor current sensor.
The compressor motor speed is lowered gradually
according to the range of TO (outside air temp.) if
the input current exceeds the current value
determined in each zone as shown in Fig. 8-2-8 so
that the input current does not exceed the set
value.
(mode), HIGH
(temp.).
(Fan), 30°C
2 Room temp. is 19°C to 24°C, and
outside air temp. is 5°C or lower.
3 Defrost operation has been already
performed once.
In case that the current lowered by approx. 0.5A
than each set value, return to above item (1).
– 29 –
FILE NO. SVM-03008
2) Defrost operation
8-2-4. Automatic operation
Operation of the compressor is stopped once,
turn off power coupler for 4-way valves after
10 seconds, and then exchange the 4-way
valves.
After 20 seconds, restart operation of the
compressor. Turn off the outdoor fan just when
the compressor stopped.
(1) As shown in Fig. 8-2-9, the operation mode
(COOL, DRY, HEAT) is selected according to the
outside temperature and room temperature when
the operation has started.
The operation in Fan mode continues until an
operation mode is selected.
If the room temperature is 20°C or higher when
“AUTO” operation started within 2 hours after
“HEAT” operation had stopped, select an operation
mode after Fan operation of ultra low fan.
In AUTO operation, the set temperature of each
operation can be corrected by the remote
controller in the range of 17 to 30°C.
If temperature of the indoor heat exchanger
lowered than 38°C, stop the indoor fan.
3) Defrost reset
Resetting operation from defrost to heating is
performed when anyone of the following
conditions is satisfied.
a. Temperature of the outdoor heat exchanger
rose to +8°C or higher.
b. A status that temperature of the outdoor
heat exchanger is +5°C or higher continued
for 80 seconds.
(2) After selecting the operation mode (COOL, DRY,
HEAT), select an operation mode again when a
status that the compressor was turned off by the
room temperature or outside air temperature
continues for 15 minutes.
c. Defrost operation continued for 15 minutes.
(3) Powerful Cool mode control
In resetting defrost operation, the compressor
stops for 50 seconds if defrost has started under
condition a. to c. in item1), but the compressor is
reset to heating operation keeping operated if
defrost has started under condition d. in item 1).
When the outside temperature is above 32°C and
indoor temperature is above 28°C, select Cool
mode control. In Cool mode, the air flow louver
directs downward. When the room temperature
gains access to the set temperature, it becomes
cool memory position.
(5) Louver control
When the compressor is turned off by high-temp.
release control, the vertical air flow louvers close
once and then return to the position of previous
time.
Powerful Cooling/Drying with
TA
setting on remote controller
Ts = 25°C
28
Cooling/Drying with setting
on remote controller
Ts = 25°C
26
24
23
Monitoring
(Follow to the Fan control in
previous mode when being
selected again.)
Heating with setting
on remote controller
Ts = 25°C
20
Ts correction by
outside temperature
To)
5
15 18
−1
24
32
To
−2
0
+1
(
Fig. 8-2-9
– 30 –
FILE NO. SVM-03008
8-3.Temporary Operation
•
Temporary Auto operation, existence of Auto
Restart, and Temporary Cooling operation can be
set by the TEMPORARY button of the indoor
controller.
TEMPORARY button
TEMPORARY button
Fig. 8-3-1
Table 8-3-1
TEMPORARY button
Control
OFF → ON
Temporary Auto operation start
After pushing button
for 3 seconds
Auto Restart
control select
After pushing button
for 10 seconds
Temporary Cooling
operation start
8-3-1. Temporary auto operation
•
When the TEMPORARY button is pushed, the
Auto operation with set temperature fixed at 25°C
starts. Controlling is same as that of Auto opera-
tion by the remote controller.
•
•
•
When the TEMPORARY button is pushed again,
the operation stops.
During Temporary Auto operation, operation by the
remote controller is accepted.
Using the Auto Restart function, the Temporary
Auto operation starts when power failure is reset.
8-3-2.Temporary cooling operation
•
When the TEMPORARY operation button keeps
pushed for 10 seconds, Cooling operation of
which compressor motor speed and the indoor fan
speed are fixed starts.
Compressor motor speed :
13 : 30 rps
Indoor fan speed : Low
•
•
When the TEMPORARY operation button is
pushed again, the operation stops.
Auto Restart function is unavailable.
– 31 –
FILE NO. SVM-03008
8-4-1. How to set auto restart function
8-4. Auto Restart Function
To set the auto restart function, proceed as follows:
The power supply to the unit must be on; the function
will not set if the power is off.
Push the [TEMPORARY] button located in the center
of the front panel continuously for three seconds.
The unit receives the signal and beeps three times.
The unit then restarts operating automatically in the
event of power supply being accidentally shut down.
The indoor unit is equipped with an automatic
restarting function which allows the unit to restart
operating with the set operating conditions in the event
of power supply being accidentally shut down. The
operation will resume without warning three minutes
after power is restored. This function is not set to work
when shipped from the factory. Therefore it is
necessary to set it to work.
•
When the unit is on standby (Not operating)
Operation
Motions
Push [TEMPORARY] button for more
than three seconds.
The unit is on standby.
The unit starts to operate.
The green lamp is on.
After approx. three seconds,
The unit beeps three times
and continues to operate.
The lamp changes from
green to orange.
0
3S
TEMPORARY button
If the unit is not required to operate at this time, push [TEMPORARY]
button once more or use the remote control to turn it off.
•
When the unit is in operation
Operation
Motions
Push [TEMPORARY] button for more
than three seconds.
The unit is in operation.
The unit stops operating.
The green lamp is on.
The green lamp is turned off.
After approx. three seconds,
The unit beeps three times.
0
3S
If the unit is required to operate at this time, push [TEMPORARY]
button once more or use the remote control to turn it on.
TEMPORARY button
•
•
•
While this function is being set, if the unit is in
operation, the orange lamp is on.
This function can not be set if the timer operation
has been selected.
When the unit is turned on by this function, the
louver will not swing even though it was swinging
automatically before shutting down.
•
While the filter check lamp is on, the
TEMPORARY button has the function of filter
reset button.
– 32 –
FILE NO. SVM-03008
8-4-2. How to cancel auto restart function
To cancel auto restart function, proceed as follows:
Repeat the setting procedure: the unit receives the
signal and beeps three times.
The unit will be required to be turned on with the
remote control after the main power supply is turned
off.
•
When the system is on standby (Not operating)
Operation
Motions
Push [TEMPORARY] button for more
than three seconds.
The unit is on standby.
The unit starts to operate.
The orange lamp is on.
After approx. three seconds,
The unit beeps three times
and continues to operate.
The lamp changes from
orange to orange.
0
3S
TEMPORARY button
If the unit is not required to operate at this time, push [TEMPORARY]
button once more or use the remote control to turn it off.
•
When the system is operating
Operation
Motions
Push [TEMPORARY] button for more
than three seconds.
The unit is in operation.
The unit stops operating.
The orange lamp is on.
The orange lamp is turned off.
After approx. three seconds,
The unit beeps three times.
0
3S
If the unit is required to operate at this time, push [TEMPORARY]
button once more or use the remote control to turn it on.
TEMPORARY button
•
While this function is being set, if the unit is in operation, the orange lamp is on.
8-4-3. Power failure during timer operation
8-5-1. How to turn off filter check lamp
When the unit is in timer operation, if it is turned off
because of power failure, the timer operation is
cancelled. Therefore, set the timer operation again.
Push [FILTER] button on the remote control.
Or push [TEMPORARY] button on the indoor unit.
Then we have to clarify it.
NOTE:
NOTE :
The Every Timer is reset while a command signal can
be received from the remote controller even if it
stopped due to a power failure.
If [TEMPORARY] button is pushed while the filter
check lamp is not indicating, the indoor unit will start
the automatic operation.
When you want a temporary operation while the filter
lamp lights, put out the lamp once, and then push the
TEMPORARY button.
8-5. Filter Check Lamp
When the elapsed time reaches 1000 hours, the filter
check lamp indicates. After cleaning the filters, turn off
the filter check lamp.
– 33 –
FILE NO. SVM-03008
$ Memory button (MEMO)
8-6. Remote Control and its Functions
Keep pushing the MEMO button for 2 seconds
from the beginning, or keep pushing the button for
2 seconds after pushing it once for a short time.
Then the set data is stored in the memory and
is displayed.
8-6-1. Parts name of remote control
1 Infrared signal emitter
Transmits a signal to the indoor unit.
2 START/STOP button
% Automatic operation button (AUTO)
Push this button to operate the air conditioner
automatically.
Push the button to start operation.
(A receiving beep is heard.)
Push the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor unit,
push the button twice.
& ECO timer button (ECO)
Push this button to start the ECO timer (OFF
timer) operation.
You can select the OFF timer from among four
settings (1,3,5 or 9 hours).
3 Mode select button (MODE)
Push this button to select a mode.
Each time you press the button, a mode is
selected in a sequence that goes from A : Auto
changeover control, : Cool, : Dry, : Heat,
: Fan only, and back to A.
( FILTER button
Push this button to turn off the filter cleaning lamp
on the indoor unit.
Push this button after cleaning the air filter.
) PRESET button
(A receiving beep is heard.)
Push this button to operate the air conditioner
according to settings memorized by the MEMO
button.
4 Temperature button (
)
,....... The set temperature is increased up to
30°C.
9.......The set temperature is dropped down to
17°C.
~ TIMER button
Use this button to change the clock, ON timer, and
OFF timer times.
To forward the time, push the “TIMER ” button.
To set back the time, push the “TIMER ” button.
(A receiving beep is heard.)
5 Fan speed button (FAN)
Push this button to select fan speed. When you
select AUTO, the fan speed is automatically
adjusted according to the room temperature.
You can also manually select the desired fan
speed from among five settings.
1
(LOW , LOW+
HIGH
, MED
, MED+
,
)
(A receiving beep is heard.)
6 Auto louver button (SWING)
Push this button to swing the louver.
(A receiving beep is heard.)
AUTOA
Push the FIX button to stop the louver swinging.
(A receiving beep is heard.)
7 Set louver button (FIX)
PRESET
Push this button to adjust the air flow direction.
(A receiving beep is heard.)
8 Off timer button (OFF)
117
START/STOP
Push this button to set the OFF timer.
9 On timer button (ON)
Push this button to set the ON timer.
! Reserve button (SET)
Push this button to reserve time settings.
(A receiving beep is heard.)
" Cancel button (CLR)
Push this button to cancel ON timer and OFF
timer. (A receiving beep is heard.)
# High power button (Hi-POWER)
AUTO
FAN
SWING
FIX
MODE
114
115
1
12
ECO
Hi-POWER
TIMER
MEMO
13
1
ON
OFF
SET
CLR
111
110
118
FILTER
RESET CLOCK CHECK
116
Push this button to start the high power operation.
– 34 –
FILE NO. SVM-03008
8-6-2. Names and functions of indications on
remote control
6 TIMER and clock time display
The time set for timer operation or clock time is
indicated.
The present time is always indicated except for
TIMER operation.
[Display]
All indications, except for clock time indication, are
indicated by pushing the START/STOP button.
7 Hi-POWER display
Indicates when the Hi-POWER operation starts.
Push the Hi-POWER button to start and push it
again to stop the operation.
1 Transmission mark
This transmission mark , indicates when the
remote controller transmits signals to the indoor
unit.
8
(MEMORY) display
Flashes for 4 seconds when the MEMO button is
pushed during operation.
mark is indicated when keeping the button
depressed for more than 4 seconds while the
mark is flashing.
2 Mode display
Indicates the current operation mode.
(AUTO : Automatic control, A : Auto changeover
control, : Cool, : Dry, : Heat, : Fan only)
3 Temperature display
Push another button to turn off the mark.
9 ECO TIMER display
Indicates the temperature setting (17 C to 30 C).
When you set the operating mode to : Fan only,
no temperature setting is indicated.
4 Louver operation display
Indicates when the ECO TIMER is in operation.
Each time you push the ECO button, the display
changes in the sequence of 1,3,5 or 9h.
Indicates the louver positioning and operation.
,
,
,
,
Five selectable positions
Swing
Automatic
5 FAN speed display
Indicates the selected fan speed. AUTO or one of
five fan speed levels (LOW , LOW+
MED , HIGH
, MED+
be indicated.
,
) can
Indicates AUTO when the operating mode is either
AUTO or : Dry.
3
1
2 8
4
A
AUTOA
9 7
5
6
•
In the illustration, all indications are indicated for explanation.
During operation, only the relevant indications will be indicated on the remote control.
– 35 –
FILE NO. SVM-03008
8-7. Hi POWER Mode ([Hi POWER] button
on the remote control is pushed.)
When [Hi POWER] button is pushed while the indoor
unit is in Auto, Cooling or Heating operation, Hi
POWER mark is indicated on the display of the remote
control and the unit operates as follows.
(1) Automatic operation
•
The indoor unit operates in according to the
current operation.
(2) Cooling operation
•
The preset temperature drops 1°C.
(The value of the preset temperature on the
remote controller does not change.)
•
If the difference between the preset tempera-
ture and the room temperature is big, the
horizontal louver moves to the Hi POWER
position automatically. Then when the differ-
ence between them gets smaller, the horizontal
louver returns automatically.
(3) Heating operation
•
The preset temperature increases 2°C. (The
value of the preset temperature on the remote
control does not change.)
•
If the difference between the preset tempera-
ture and the room temperature is big, the
horizontal louver moves to the Hi POWER
position automatically. Then when the differ-
ence between them gets smaller, the horizontal
louver returns automatically.
(4) The Hi POWER mode can not be set in Dry or Fan
only operation.
– 36 –
FILE NO. SVM-03008
9. INSTALLATION PROCEDURE
For general public use
9-1. Safety Cautions
Power supply cord of parts of appliance for outdoor use shall be at least polychloroprene sheathed flexible
cord (design H07RN-F), or cord designation 245 IEC66. (1.5 mm2 or more)
New Refrigerant Air conditioner Installation
CAUTION
• THIS AIR CONDITIONER USESTHE NEW HFC REFRGERANT (R410A), WHICH DOES NOT
DESTROY THE OZONE LAYER.
R410A refrigerant is apt to be affected by impurity such as water, oxidizing membranes, and oils because
the pressure of R410A refrigerant is approx. 1.6 times of refrigerant R22. As well as the adoption of this new
refrigerant, refrigerating machine oil has also been changed. Therefore, during installation work, be sure that
water, dust, former refrigerant, or refrigerating machine oil does not enter into the refrigerating cycle of a
new-refrigerant air conditioner.
To avoid mixing refrigerant and refrigerating machine oil, the sizes of charging port connecting sections on
the main unit are different from those for the conventional refrigerant, and different size tools are also
required. Accordingly, special tools are required for the new refrigerant (R410A) as shown below. For
connecting pipes, use new and clean piping materials with high-pressure withstand capabilities, designed for
R410A only, and ensure that water or dust does not enter. Moreover, do not use any existing piping as its
pressure withstand may be insufficient, and may contain impurities.
To Disconnect the Appliance from the Main Power Supply
CAUTION
This appliance must be connected to the main power supply by means of a circuit breaker or a switch with a
contact separation of at least 3 mm.
The installation fuse (25A D type
conditioner. (RAS-13UKV-E2 only)
) must be used for the power supply line of this air
– 37 –
FILE NO. SVM-03008
DANGER
•
•
FOR USE BY QUALIFIED PERSONS ONLY.
TURN OFF MAIN POWER SUPPLY BEFORE ATTEMPTING ANY ELECTRICAL WORK. MAKE SURE
ALL POWER SWITCHES ARE OFF. FAILURE TO DO SO MAY CAUSE ELECTRIC SHOCK.
CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED
WRONGLY, ELECTRIC PARTS MAY BE DAMAGED.
•
•
•
CHECK THE EARTH WIRE THAT IT IS NOT BROKEN OR DISCONNECTED BEFORE INSTALLATION.
DO NOT INSTALL NEAR CONCENTRATIONS OF COMBUSTIBLE GAS OR GAS VAPORS.
FAILURE TO FOLLOW THIS INSTRUCTION CAN RESULT IN FIRE OR EXPLOSION.
TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE HAZARD, PLACE THE UNIT
WELL AWAY (MORE THAN 2 M) FROM HEAT SOURCES SUCH AS RADIATORS, HEATERS,
FURNACE, STOVES, ETC.
•
•
WHEN MOVING THE AIR-CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY
CAREFUL NOT TO GET THE SPECIFIED REFRIGERANT WITH ANY OTHER GASEOUS BODY INTO
THE REFRIGERATION CYCLE. IF AIR OR ANY OTHER GAS IS MIXED IN THE REFRIGERANT, THE
GAS PRESSURE IN THE REFRIGERATION CYCLE BECOMES ABNORMALLY HIGH AND IT
RESULTINGLY CAUSES BURST OF THE PIPE AND INJURIES ON PERSONS.
•
IN THE EVENT THAT THE REFRIGERANT GAS LEAKS OUT OF THE PIPE DURING THE
INSTALLATION WORK, IMMEDIATELY LET FRESH AIR INTO THE ROOM. IF THE REFRIGERANT GAS
IS HEATED BY FIRE OR SOMETHING ELSE, IT CAUSES GENERATION OF POISONOUS GAS.
WARNING
•
•
•
•
Never modify this unit by removing any of the safety guards or bypassing any of the safety interlock
switches.
Do not install in a place which cannot bear the weight of the unit.
Personal injury and property damage can result if the unit falls.
Before doing the electrical work, attach an approved plug to the power supply cord.
Also, make sure the equipment is properly earthed.
Appliance shall be installed in accordance with national wiring regulations.
If you detect any damage, do not install the unit. Contact your TOSHIBA dealer immediately.
CAUTION
•
Exposure of unit to water or other moisture before installation could result in electric shock.
Do not store it in a wet basement or expose to rain or water.
•
•
After unpacking the unit, examine it carefully for possible damage.
Do not install in a place that can increase the vibration of the unit. Do not install in a place that can amplify
the noise level of the unit or where noise and discharged air might disturb neighbors.
To avoid personal injury, be careful when handling parts with sharp edges.
Please read this installation manual carefully before installing the unit. It contains further important
instructions for proper installation.
•
•
– 38 –
FILE NO. SVM-03008
9-1-1. Installation Diagram of Indoor and Outdoor Units
For the rear left and left
piping
Wall
Hook
1 Installation
plate
Insert the cushion between
the indoor unit and wall, and
lift the indoor unit for better
operation.
Do not allow the drain hose
to get slack.
Shield
pipe
Cut the piping
hole sloped
slightly
5 Zeolite filter
6 Purifying filter
Make sure to run the drain
hose sloped downward.
8 Flat head wood screw
The auxiliary piping can be
connected the left, rear left,
rear right, right, bottom right
or bottom left.
Before installing the
wireless remote control
• With the remote control cover
open, load the batteries supplied
4 Remote control holder
2 Wireless remote control
correctly, observing their polarity.
2 Wireless remote control
Right
Cover
Rear right
Rear
Left
left
Bottom
right
Vinyl tape Apply
after carrying out
a drainage test
Bottom left
3 Batteries
Insulate the refrigerant
pipes separately with
insulation, not together.
Saddle
6 mm thick heat resisting
polyethylene foam
Extension
drain hose
(Option:
RB–821SW)
As show in the figure, hang
power cord and connecting
cable downward, and take out it
along piping connection port.
Fig. 9-1-1
– 39 –
FILE NO. SVM-03008
9-1-2. Optional installation parts
Part
Parts name
Code
Q’ty
Refrigerant piping
Liquid side : ∅6.35 mm
Gas side : ∅9.52 mm
One
each
A
Pipe insulating material
(polyethylene foam, 6 mm thick)
B
C
1
One
each
Putty, PVC tapes
<Fixing bolt arrangement of outdoor unit>
600
Suction side
115
Drain hole
Diffuser
Fig. 9-1-2
•
•
•
Secure the outdoor unit with the fixing bolts and nuts if the unit is likely to be exposed to a strong wind.
Use ∅8 mm or ∅10 mm anchor bolts and nuts.
If it is necessary to drain the defrost water, attach drain nipple to the bottom plate of the outdoor unit
before installing it.
– 40 –
FILE NO. SVM-03008
9-1-3. Accessory and installation parts
Part
No.
Part
No.
Part
No.
Part name (Q’ty)
Part name (Q’ty)
Part name (Q’ty)
1
2
3
4
5
6
7
8
Installation plate x 1
Remote control holder x 1
Mounting screw ∅4 x 25 s x 6
Flat head wood screw
∅3.1 x 16 s x 2
Wireless remote control x 1
Zeolite filter x 1
9
Drain nipple* x 1
Battery x 2
Purifying filter x 1
The part marked with asterisk ( ) is packaged with the
*
outdoor unit.
Others
Name
Owner’s manual
Installation manual
This model is not equipped with an extension drain hose.
Option :
For the extension drain hose, use an optionally available RB-821SW or commercially available one.
– 41 –
FILE NO. SVM-03008
9-1-4. Installation/Servicing Tools
<Changes in the product and components>
In the case of an air conditioner using R410A, in order to prevent any other refrigerant from being charged
accidentally, the service port diameter of the outdoor unit control valve (3 way valve) has been changed.
(1/2 UNF 20 threads per inch)
•
In order to increase the pressure resisting strength of the refrigerant piping, flare processing diameter and
size of opposite side of flare nuts has been changed. (for copper pipes with nominal dimensions 1/2 and 5/8)
New tools for R410A
New tools for R410A
Applicable to R22 model
Changes
Gauge manifold
As pressure is high, it is impossible to measure by
means of conventional gauge. In order to prevent any
other refrigerant from being charged, each port
diameter has been changed.
Charge hose
In order to increase pressure resisting strength, hose
materials and port size have been changed (to 1/2
UNF 20 threads per inch).
When purchasing a charge hose, be sure to confirm
the port size.
Electronic balance
for refrigerant charging
As pressure is hight and gasification speed is fast, it
is difficult to read the indicated value by means of
charging cylinder, as air bubbles occur.
Torque wrench
(nominal diam. 1/2, 5/8)
The size of opposite sides of flare nuts have been
increased. Incidentally, a common wrench is used for
nominal diameters 1/4 and 3/8.
Flare tool
(clutch type)
By increasing the clamp bar’s receiving hole, strength
of spring in the tool has been improved.
Gauge for projection
adjustment
Used when flare is made by using conventional flare
tool.
Vacuum pump adapter
Connected to conventional vacuum pump. It is
necessary to use an adapter to prevent vacuum
pump oil from flowing back to the charge hose.
The charge hose connecting part has two ports-one
for conventional refrigerant (7/16 UNF 20 threads per
inch) and one for R410A. If the vacuum pump oil
(mineral) mixes with R410A a sludge may occur and
damage the equipment.
Gas leakage detector
Exclusive for HFC refrigerant.
•
•
Incidentally, the “refrigerant cylinder” comes with the refrigerant designation (R410A) and protector coating in
the U. S’s ARI specified rose color (ARI color code: PMS 507).
Also, the “charge port and packing for refrigerant cylinder” require 1/2 UNF 20 threads per inch
corresponding to the charge hose’s port size.
– 42 –
FILE NO. SVM-03008
9-2-2. Cutting a hole and mounting installation
plate
9-2. Indoor Unit
9-2-1. Installation place
<Cutting a hole>
•
•
•
A place which provides the spaces around the
indoor unit as shown in the above diagram.
A place where there is no obstacle near the air inlet
and outlet.
A place that allows easy installation of the piping to
the outdoor unit.
When installing the refrigerant pipes from the rear.
•
•
A place which allows the front panel to be opened.
The indoor unit shall be installed as top of the
indoor unit comes to at least 2 m height.
Also it must be avoided to put anything on the top of
the indoor unit.
Pipe hole
65 mm
The center of the pipe
hole is above the arrow.
100 mm
CAUTION
Fig. 9-2-2
• Direct sunlight to the indoor unit’s wireless
receiver should be avoided.
1. After determining the pipe hole position on the
mounting plate (A), drill the pipe hole (∅65 mm) at
a slight downward slant to the outdoor side.
• The microprocessor in the indoor unit should not
be too close to RF noise sources.
(For details, see the owner’s manual.)
NOTE:
<Remote controller>
•
When drilling a wall that contains a metal lath, wire
lath or metal plate, be sure to use a pipe hole brim
ring sold separately.
•
•
•
A place where there are no obstacles such as a
curtain that may block the signal from the indoor
unit.
Do not install the remote control in a place exposed
to direct sunlight or close to a heating source, such
as a stove.
Keep the remote control at least 1 m apart from the
nearest TV set or stereo equipment. (This is
necessary to prevent image disturbances or noise
interference.)
<Mounting the installation plate>
For installation of the indoor unit, use the paper pattern
on the back.
Anchor bolt holes
62
82.5
Hook
•
The location of the remote control should be
determined as shown below.
170
85
(Side view)
(Top view)
Indoor unit
1
Installation
plate
Hook
Pipe
hole
Hook
Pipe hole
Thread
7 Mounting screw
Reception
range
Remote
control
Weight
Indoor unit
Reception
range
Remote
control
* : Axial distance
Fig. 9-2-3
Fig. 9-2-1
– 43 –
FILE NO. SVM-03008
<When the installation plate is directly mounted on 9-2-3. Electrical work
the wall>
1. The supply voltage must be the same as the rated
voltage of the air conditioner.
1. Securely fit the installation plate onto the wall by
screwing it in the upper and lower parts to hook up 2. Prepare the power source for exclusive use with the
the indoor unit.
air conditioner.
2. To mount the installation plate on a concrete wall
with anchor bolts, utilize the anchor bolt holes as
illustrated in the above figure.
NOTE:
•
Wire type : More than H07RN-F or 245 IEC66
(1.0 mm2 or more)
3. Install the installation plate horizontally in the wall.
CAUTION
CAUTION
When installing the installation plate with a
mounting screw, do not use the anchor bolt hole.
Otherwise the unit may fall down and result in
personal injury and property damage.
• This appliance can be connected to the mains in
either of the following two ways.
(1) Connection to fixed wiring :
A switch or circuit breake which disconnects
all poles and has a contact separation of at
least 3 mm must be incorporate in the fixed
wiring. An approved circuit breaker or
switches must used.
Installation plate
<Keep horizontal direction>
Anchor
bolt
(2) Connection with power supply plug :
Attach power supply plug with power cord and
plug it into wall outlet. An approved power
supply cord and plug must be used.
Projection
15 mm or less
NOTE:
•
Fig. 9-2-4
Perform wiring works so as to allow a generous
wiring capacity.
5 mm dia. hole
7 Mounting
screw
∅4 x 25s
Clip anchor
(local parts)
Fig. 9-2-5
CAUTION
Failure to firmly install the unit may result in
personal injury and property damage if the unit falls.
•
•
In case of block, brick, concrete or similar type
walls, make 5 mm dia. holes in the wall.
Insert clip anchors for appropriate mounting screws
7.
NOTE:
Secure four corners and lower parts of the
•
installation plate with 4 to 6 mounting screws to
install it.
– 44 –
FILE NO. SVM-03008
9-2-4. Wiring connection
9-2-5. Piping and drain hose installation
<How to connect the connecting cable>
<Piping and Drain Hose Forming>
Wiring of the connecting cable can be carried out
without removing of the front panel.
*
Since dewing results in a machine trouble, make
sure to insulate both the connecting pipes. (Use
polyethylene foam as insulating material.)
1. Remove the air inlet grille.
Open the air inlet grille upward and pull it toward
you.
2. Remove the terminal cover and cord clamp.
3. Insert the connecting cable (according to the local
cords) into the pipe hole on the wall.
4. Take out the connecting cable through the cable
slot on the rear panel so that it protrudes about
15 cm from the front.
5. Insert the connecting cable fully into the terminal
block and secure it tightly with screws.
6. Tightening torque : 1.2 N·m (0.12 kgf·m)
7. Secure the connecting cable with the cord clamp.
8. Fix the terminal cover, rear plate bushing and air
inlet grille on the indoor unit.
Rear right
Rear left
Bottom left
Left
Bottom right
Right
Fig. 9-2-8
1. Die-cutting Front panel slit
Cut out the slit on the left or right side of the front panel
for the left or right connection and the slit on the
bottom left or right side of the front panel for the
bottom left or right connection with a pair of nippers.
CAUTION
• Be sure to refer to the wiring system diagram
labeled inside the front panel.
• Check local electrical cords and also any specific
wiring instructions or limitations.
2. Changing drain hose
For left connection, bottom-leftward connection and
rear-leftward connection’s piping, it is necessary to
change the drain hose and drain cap.
Terminal block
Terminal cover
Cord clamp
<How to remove the Drains Cap>
Clip drain cap by needle-nose pliers, and pull out.
Screw
Connecting
cable
Earth line
Connecting cable
Earth line
Screw
Screw
Fig. 9-2-9
Fig. 9-2-6
<How to install the Drain Hose>
Firmly insert drain hose connecting part until hitting on
a heat insulator.
80 mm
10 mm
10 mm
Heat insulator
10 mm
50 mm
Drain hose
NOTE:
Fig. 9-2-10
•
Wire type : More than H07RN-F or 245 IEC66
(1.0 mm2 or more)
Fig. 9-2-7 Stripping length of connecting cable
– 45 –
FILE NO. SVM-03008
<How to fix the Drains Cap>
<Left-hand connection with piping>
1) Insert hexagonal wrench (∅4 mm) in a center head. Bend the connecting pipe so that it is laid within 43 mm
above the wall surface. If the connecting pipe is laid
exceeding 43 mm above the wall surface, the indoor
unit may unstably be set on the wall. When bending the
connecting pipe, make sure to use a spring bender so
as not to crush the pipe.
∅4 mm
Bend the connection pipe within a radius of 30 mm
(∅6.35) 40 mm (∅9.52).
Fig. 9-2-11
To connect the pipe after installation of the unit (figure)
2) Firmly insert drains cap.
(To the forefront of flare)
270 mm
Liquid side
No gap
170 mm
Gas side
Do not apply lubricating oil
(refrigerant machine oil) when
inserting the drain cap. Application
causes deterioration and drain
leakage of the plug.
Outward form of indoor unit
Insert a hexagon
wrench (∅4 mm)
R 30 mm or less (∅6.35) R 40 mm or less (∅9.52)
(Use polisin (polyethylene core) or the like for
bending pipe.)
Fig. 9-2-12
Use the handle of screwdriver, etc.
CAUTION
Fig. 9-2-15
Firmly insert the drain hose and drain cap;
otherwise, water may leak.
NOTE:
If the pipe is bent incorrectly, the indoor unit may
unstably be set on the wall.
After passing the connecting pipe through the pipe
hole, connect the connecting pipe to the auxiliary pipes
and wrap the facing tape around them.
<In case of right or left piping>
•
After scribing slits of the front panel with a knife or a
making-off pin, cut them with a pair of nippers or an
equivalent tool.
CAUTION
• Bind the auxiliary pipes (two) and connecting
cable with facing tape tightly. In case of leftward
piping and rear-leftward piping, bind the auxiliary
pipes (two) only with facing tape.
Slit
Fig. 9-2-13
Indoor unit
Auxiliary pipes
Connecting cable
<In case of bottom right or bottom left piping>
•
After scribing slits of the front panel with a knife or a
making-off pin, cut them with a pair of nippers or an
equivalent tool.
Installation plate
Fig. 9-2-16
• Carefully arrange pipes so that any pipe does not
stick out of the rear plate of the indoor unit.
• Carefully connect the auxiliary pipes and
connecting pipes to each other and cut off the
insulating tape wound on the connecting pipe to
avoid double-taping at the joint, moreover, seal
the joint with the vinyl tape, etc.
Slit
Fig. 9-2-14
• Since dewing results in a machine trouble, make
sure to insulate both the connecting pipes. (Use
polyethylene foam as insulating material.)
• When bending a pipe, carefully do it not to crush it.
– 46 –
FILE NO. SVM-03008
9-2-6. Indoor unit fixing
2. Put water in the drain pan and make sure that the
water is drained out of doors.
3. When connecting extension drain hose, insulate the
connecting part of extension drain hose with shield
pipe.
1. Pass the pipe through the hole in the wall, and hook
the indoor unit on the installation plate at the upper
hooks.
2. Swing the indoor unit to right and left to confirm that
it is firmly hooked up on the installation plate.
3. While pressing the indoor unit onto the wall, hook it
at the lower part on the installation plate. Pull the
indoor unit toward you to confirm that it is firmly
hooked up on the installation plate.
Shield pipe
Extension drain hose
Inside the room
Drain hose
Fig. 9-2-20
Hook here
1
1 Installation plate
CAUTION
Arrange the drain pipe for proper drainage from the
unit.
Improper drainage can result in dew-dropping.
2
Hook
Push
(unhook)
Fig. 9-2-17
This air conditioner has the structure designed to drain
water collected from dew, which forms on the back of
the indoor unit, to the drain pan.
Therefore, do not store the power cord and other parts
at a height above the drain guide.
•
For detaching the indoor unit from the installation
plate pull the indoor unit toward you while pushing
its bottom up at the specified parts.
Wall
Drain guide
Space for pipes
Push
Push
Fig. 9-2-18
Fig. 9-2-21
9-2-7. Drainage
1. Run the drain hose sloped downwards.
NOTE:
•
Hole should be made at a slight downward slant on
the outdoor side.
Do not form the
drain hose into
a wavy shape.
Do not rise the
drain hose.
50 mm
or more
Do not put
the drain
hose end
into water.
Do not put
the drain
hose end in
the drainage
ditch.
Fig. 9-2-19
– 47 –
FILE NO. SVM-03008
9-3-2. Refrigerant piping connection
9-3. Outdoor Unit
<Flaring>
9-3-1. Installation place
1. Cut the pipe with a pipe cutter.
•
•
A place which provides the spaces around the
outdoor unit as shown in the left diagram.
A place which can bear the weight of the outdoor
unit and does not allow an increase in noise level
and vibration.
Roughness
Obliquity
Warp
90°
•
A place where the operation noise and discharged
air do not disturb users neighbors.
Fig. 9-3-2
•
•
•
•
A place which is not exposed to a strong wind.
A place free of a leakage of combustible gases.
A place which does not block a passage.
When the outdoor unit is to be installed in an
elevated position, be sure to secure its feet.
An allowable length of the connecting pipe is up
15 m.
2. Insert a flare nut into the pipe, and flare the pipe.
• Projection margin in flaring : A (Unit : mm)
A
•
•
•
An allowable height level is up to 10 m.
A place where the drain water does not raise any
problem.
Die
Pipe
Fig. 9-3-3
CAUTION
Rigid (Clutch type)
1. Install the outdoor unit without anything blocking
the air discharging.
Outer dia.
R410A
tool used
Conventional
tool used
2. When the outdoor unit is installed in a place
exposed always exposed to strong wind like a
coast or on a high storey of a building, secure
the normal fan operation using a duct or a wind
shield.
of copper pipe
6.35
9.52
0 to 0.5
0 to 0.5
1.0 to 1.5
1.0 to 1.5
3. In particularly windy areas, install the unit such
as to avoid admission of wind.
4. Installation in the following places may result in
trouble.
Imperial (wing nut type)
Outer dia.
of copper pipe
R410A
Do not install the unit in such places.
• A place full of machine oil.
6.35
9.52
1.5 to 2.0
1.5 to 2.0
• A saline-place such as the coast.
• A place full of sulfide gas.
<Tightening connection>
• A place where high-frequency waves are likely
to be generated as from audio equipment,
welders, and medical equipment.
Align the centers of the connecting pipes and tighten
the flare nut as far as possible with your fingers. Then
tighten the nut with a spanner and torque wrench as
shown in the figure.
Half union
Flare nut
Strong
wind
Externally
Internally
threaded side
threaded side
Use a wrench to secure.
Use a torque wrench to tighten.
Fig. 9-3-1
Fig. 9-3-4
CAUTION
• Do not apply excess torque.
• Otherwise, the nut may crack depending on the
conditions.
– 48 –
FILE NO. SVM-03008
(Unit : N·m) 9-3-3. Evacuating
Outer dia.
of copper pipe
After the piping has been connected to the indoor unit,
you can perform the air purge together at once.
Tightening torque
∅6.35 mm
16 to 18 (1.6 to 1.8 kgf·m)
30 to 42 (3.0 to 4.2 kgf·m)
AIR PURGE
Evacuate the air in the connecting pipes and in the
indoor unit using a vacuum pump. Do not use the
refrigerant in the outdoor unit. For details, see the
manual of the vacuum pump.
∅9.52 mm
•
Tightening torque of flare pipe connections
The operating pressure of R410A is higher than that of
R22. (Approx. 1.6 times).
<Using a vacuum pump>
It is therefore necessary to firmly tighten the flare pipe
connecting sections (which connect the indoor and
outdoor units) up to the specified tightening torque.
Incorrect connections may cause not only a gas
leakage, but also damage to the refrigerant cycle.
Be sure to use a vacuum pump with counter-flow
prevention function so that inside oil of the pump does
not flow backward into pipes of the air conditioner
when the pump stops. (If oil inside of the vacuum pump
enters into the air conditioner, which use R410A,
refrigeration cycle trouble may result.)
1. Connect the charge hose from the manifold valve to
the service port of the gas side packed valve.
2. Connect the charge hose to the port of the vacuum
pump.
Flare at
indoor unit side
3. Open fully the low pressure side handle of the
gauge manifold valve.
4. Operate the vacuum pump to start evacuating.
Perform evacuating for about 15 minutes if the
piping length is 20 meters. (15 minutes for
20 meters) (assuming a pump capacity of 27 liters
per minute. Then confirm that the compound
pressure gauge reading is –101 kPa (–76 cmHg).
5. Close the low pressure side valve handle of gauge
manifold.
6. Open fully the valve stem of the packed valves
(both side of Gas and Liquid).
7. Remove the charging hose from the service port.
8. Securely tighten the caps on the packed valves.
Flare at
outdoor unit side
Fig. 9-3-5
<Shaping pipes>
1. How to shape the pipes
Shape the pipes along the incused line on the
outdoor unit.
2. How to fit position of the pipes
Put the edges of the pipes to the place with a
distance of 85 mm from the incused line.
Compound
Pressure gauge
pressure
gauge
-101kPa
Manifold valve
(-76cmHg)
Handle Hi
Handle Lo
(Keep full closed)
Charge hose
(For R410A only)
Charge hose
(For R410A only)
Vacuum pump
adapter for
Incused line
counter-flow
prevention
Connecting
pipe
(For R410A only)
Vacuum
pump
Packed valve at liquid side
Packed valve at gas side
Service port
(Valve core (Setting pin))
Fig. 9-3-6
Fig. 9-3-7
CAUTION
• KEEP IMPORTANT 4 POINTS FOR PIPING
WORK
(1) Take away dust and moisture (Inside of the
connecting pipes.)
(2) Tight connection (between pipes and unit)
(3) Evacuate the air in the connecting pipes using
VACUUM PUMP.
(4) Check gas leak (connected points)
– 49 –
FILE NO. SVM-03008
<Packed valve handling precautions>
<Stripping length of connection cable>
•
•
Open the valve stem all the way out; but do not try
to open it beyond the stopper.
Securely tighten the valve stem cap with torque in
the following table:
Terminal block
Gas side
30 to 42 N·m
(∅9.52 mm)
(3.0 to 4.2 kgf·m)
Liquid side
16 to 18 N·m
Power cord
(∅6.35 mm)
(1.6 to 1.8 kgf·m)
Connecting cable
9 to 10 N·m
(0.9 to 1.0 kgf·m)
Service port
1
2
3
L
N
40
40
Hexagonal wrench
is required.
30
30
Earth line
Earth line
Power cord
Connecting cable
Fig. 9-3-9
Model
RAS-13UKV-E2
Fig. 9-3-8
9-3-4. Wiring connection
Power source
50/60 Hz, 220 – 240 V Single phase
Maximum
running current
11A
1. Remove the valve cover from the outdoor unit.
2. Connect the connecting cable to the terminal as
identified with their respective matched numbers on
the terminal block of indoor and outdoor unit.
3. When connecting the connecting cable to the
outdoor unit terminal, make a loop as shown in the
installation diagram of indoor and outdoor unit, to
prevent water coming in the outdoor unit.
Installation fuse
rating
25A (D type
)
H07RN-F or 245 IEC66 (1.5 mm2
or more)
Power cord
CAUTION
4. Insulate the unused cords (conductors) from any
water coming in the outdoor unit. Proceed them so
that they do not touch any electrical or metal parts.
• Wrong wiring connection may cause some
electrical parts burn out.
• Be sure to comply with local codes on running
the wire from indoor unit to outdoor unit (size of
wire and wiring method etc).
• Every wire must be connected firmly.
• This installation fuse (25A D type
) must
be used for the power supply line of this air
conditioner.
• If incorrect or incomplete wiring is carried out, it
will cause an ignition or smoke.
• Prepare the power supply for exclusive use with
the air conditioner.
• This product can be connected to the mains.
Connection to fixed wiring: A switch which
disconnects all poles and has a contact
separation of at least 3 mm must be incorporated
in the fixed wiring.
NOTE: Connecting cable
•
Wire type: More than H07RN-F or 245 IEC66
(1.0 mm2 or more)
– 50 –
FILE NO. SVM-03008
9-3-5. Gas leak test
9-3-7. Auto restart setting
This product is designed so that, after a power failure,
it can restart automatically in the same operating mode
as before the power failure.
Check places for
indoor unit (Flare
nut connection)
Valve cover
Information
The product was shipped with Auto Restart function
in the off position. Turn it on as required.
<How to set the auto restart>
Electric parts
cover
•
Press and hold down the TEMPORARY button for
about 3 seconds. After 3 seconds, the electronic
beeper makes three short beeps to tell you the Auto
Restart has been selected.
•
To cancel the Auto Restart, follow the steps
described in the section Auto Restart Function of
the Owner’s Manual.
Check places
for outdoor unit
Fig. 9-3-10
•
Check the flare nut connections for the gas leak
with a gas leak detector or soap water.
9-3-6. Test operation
To switch the TEST RUN (COOL) mode, push
TEMPORARY button for 10 sec.
(The beeper will make a short beep.)
TEMPORARY button
Fig. 9-3-11
– 51 –
FILE NO. SVM-03008
10. HOW TO DIAGNOSE THE TROUBLE
The pulse modulating circuits are mounted to both
NOTE:
indoor and outdoor units. Therefore, diagnose troubles
according to the diagnosis procedure as described
below. (Refer to the check points in servicing written
on the wiring diagrams attached to the indoor/outdoor
units.)
A large-capacity electrolytic capacitor is used in the
outdoor unit control (inverter). Therefore, if the power
supply is turned off, charge (charging voltage DC280V)
remains and discharging takes a lot of time. After
turning off the power source, if touching the charging
section before discharging, an electrical shock may be
caused. Discharge the electrolytic capacitor completely
by using soldering iron, etc.
Table 10-1
No.
1
Troubleshooting Procedure
First Confirmation
Page
52
<Discharging method>
2
Primary Judgment
53
(1) Remove the inverter cover (plating) by opening four
mounting claws.
3
Judgment by Flashing LED
of Indoor Unit
54
(2) As shown below, connect the discharge resistance
(approx. 100Ω40W) or plug of the soldering iron to
voltage between + – terminals of the C14
(“CAUTION HIGH VOLTAGE 380 V” is indicated.)
electrolytic capacitor (500µF/400 V) on P.C. board,
and then perform discharging.
4
5
Self-Diagnosis by Remote Control
55
58
Judgment of Trouble by
Every Symptom
6
How to Check Simply the Main Parts
66
Inverter cover
Plug of
soldering
iron
P. C. board
(Soldered surface)
Discharging position
(Discharging period
10 seconds or more)
Fig. 10-1
10-1-2. Confirmation of power voltage
10-1. First Confirmation
Confirm that power voltage is AC 220-240 V ± 10%. If
power voltage is not in this range, the unit may not
operate normally.
10-1-1. Confirmation of power supply
Confirm that the power breaker operates (ON)
normally.
– 52 –
FILE NO. SVM-03008
10-1-3. Operation which is not a trouble (Program operation)
For controlling the air conditioner, the program operations are built in the microcomputer as described in the
following table. If a claim is made for running operation, check whether or not it meets to the contents in the
following table. When it does, we inform you that it is not trouble of equipment, but it is indispensable for control-
ling and maintaining of air conditioner.
Table 10-1-1
No.
Operation of air conditioner
Description
1
When power breaker is turned “ON”,
the operation lamp (Green) of the
indoor unit flashes.
The OPERATION lamp of the indoor unit flashes when power source
is turned on. If [START/STOP] button is operated once, flashing stops.
(Flashes also in power failure)
2
Compressor may not operate even if
the room temperature is within range of
compressor-ON.
The compressor does not operate while compressor restart delay
timer (3-minutes timer) operates. The same phenomenon is found
after power source has been turned on because 3-minutes timer
operates.
3
4
In Dry and ECO. mode, FAN (air flow)
display does not change even though
FAN (air flow select) button is operated.
The air flow indication is fixed to [AUTO].
Increasing of compressor motor speed
stops approx. 30 seconds after
For smooth operation of the compressor, the compressor motor speed
is restricted to Max. 41 rps for 2 minutes, and Max.91 rps for 2 minutes
operation started, and then compressor to 3 minutes, respectively after the operation has started.
motor speed increases again approx.
30 seconds after.
5
The set value of the remote control
should be below the room temperature.
If the set value is above the room temperature, Cooling operation is
not performed. And check whether battery of the remote control is
consumed or not.
6
7
In AUTO mode, the operation mode is
changed.
After selecting Cool or Heat mode, select an operation mode again if
the compressor keeps stop status for 15 minutes.
In HEAT mode, the compressor motor
speed does not increase up to the
maximum speed or decreases before
the temperature arrives at the set
temperature.
The compressor motor speed may decrease by high-temp. release
control (Release protective operation by temp.-up of the indoor heat
exchanger) or current release control.
10-2. Primary Judgment
To diagnose the troubles, use the following methods.
(1) Judgment by flashing LED of indoor unit
(2) Self-diagnosis by service check remote control
(3) Judgment of trouble by every symptom
Firstly, use the method (1) for diagnosis. Then, use the method (2) and (3) to diagnose the details of troubles.
– 53 –
FILE NO. SVM-03008
10-3. Judgment by Flashing LED of Indoor Unit
While the indoor unit monitors the operation status of the air conditioner, if the protective circuit operates, the
contents of self-diagnosis are displayed with block on the indoor unit indication section.
Table 10-3-1
Check
Item
A
Block display
Description for self-diagnosis
code
B
C
D
E
NOTES:
(1) The contents of items B and C and a part of item E are displayed when air conditioner operates.
(2) When item B and C, and item B and a part of item E occur concurrently, priority is given to the block of item B.
(3) The check codes can be confirmed on the remote control for servicing.
– 54 –
FILE NO. SVM-03008
10-4. Self-Diagnosis by Remote Control
(Check Code)
(1) If the lamps are indicated as shown B to H in
Table 10-3-1, excute the self-diagnosis by the
remote control.
(2) When the remote control is set to the service
mode, the indoor control diagnoses the operation
condition and indicate the information of the
self-diagnosis on the display of the remote control
with the check codes. If a fault is detected, all
lamps on the indoor unit will flashes at 5Hz and it
will beep for 10 seconds (Pi, Pi, Pi....). The timer
lamp usually flashes (5Hz) during self-diagnosis.
10-4-1. How to use remote control in service mode
SET
CLR
RESET CLOCK CHECK
(1) Push [CHECK] button with a tip of pencil to set the
remote control to the service mode.
• “00” is indicated on the display of the remote
control.
• The timer lamp of the indoor unit flashes
continuously. (5 times per 1 sec.)
AUTOA
(2) Push [TIMER 8] button.
If there is no fault with a code, the indoor unit will
beep once (Pi) and the display of the remote
control will change as follows:
PRESET
START/STOP
00
01
02 1d
1E
22
AUTO
FAN
SWING
FIX
MODE
• Check the unit with all 35 check codes (00 to 22)
as shown in Table 10-4-1.
ECO
Hi-POWER
TIMER
MEMO
• Push [TIMER 9] button to change the check
code backward.
ON
OFF
SET
CLR
If there is a fault, the indoor unit will beep for 10
seconds (Pi, Pi, Pi...).
FILTER
RESET CLOCK CHECK
Note the check code on the display of the remote
control.
• 2-digits alphanumeric will be indicated on the
display.
• All lamps on the indoor unit will flash. (5 times
per 1 sec.)
(3) Push [CLR] button. After service finish for clear
service code in memory.
• “7F” is indicated on the display of the remote
control.
(4) Push [START/STOP] button to release the service
mode.
Alphanumeric characters are used for the check code.
• The display of the remote control returns to as it
was before service mode was engaged.
is 5.
is A.
is C.
is 6.
is B.
is D.
Fig. 10-4-1
– 55 –
FILE NO. SVM-03008
10-4-2. Caution at servicing
(1) After servicing, push the START/STOP button to return to the normal mode.
(2) After servicing by the check code, turn off breaker of the power supply, and turn on breaker of the power
supply again so that memory in the microcomputer returns the initial status. However, the check codes are
not deleted even if the power supply is turned off because they are stored in the fixed memory.
Table 10-4-1
Block distinction
Operation of diagnosis function
Air conditioner
Judgment and action
Check
Block
Check
code
Cause of operation
Remarks
code
status
Displayed when
error is detected.
Indoor
P. C.
board
etc.
Short-circuit or disconnec-
tion of the room
temperature sensor
(TA sensor).
Operation
continues.
1. Check the room temp. sensor.
2. When the room temp. sensor is
normal, check P.C. board.
Displayed when
error is detected.
Being out of place,
disconnection, short-circuit,
or migration of heat
exchanger sensor
(TC sensor)
Operation
continues.
1. Check heat exchanger sensor.
2. When heat exchanger sensor is
normal, check P.C. board.
Displayed when
error is detected.
Lock of indoor fan or trouble All off
on the indoor fan circuit
1. Check P.C. board.
2. When P.C. board is normal, check
the motor.
Displayed when
error is detected.
Not
displayed
Trouble on other indoor
P.C. boards
Operation
continues.
Replace P.C. board.
Flashes when
trouble is
Connec-
ting cable
and serial
signal
Return serial signal is not
sent to indoor side from
operation started.
(1) Defective wiring of
connecting cable
(2) Operation of
Operation
continues.
1. When the outdoor unit never
operate:
(1) Check connecting cable, and
correct if defective wiring.
(2) Check 25A fuse of inverter
P.C. board
detected on
return serial
signal, and
normal status
when signal is
reset.
compressor thermo.
Gas shortage
(3) Check 3.15A of inverter
P.C. board.
Gas leak
2. To display [Other] block during
operation, check compressor
thermo. operation and supply gas
(check gas leak also).
3. Unit operates normally during
check.
If Return serial signal does not
stop between 2 and 3 of the
indoor terminal block, replace
inverter P.C. board.
If signal stops between indoor
terminal block 2 and 3, replace
indoor P.C. board.
Flashes when
trouble is
detected on
operation
command signal,
and normal status
when signal is
reset.
Operation command signal
is not sent to outdoor side.
Operation
continues.
If return serial signal does not stop
between indoor terminal block 2
and 3, replace inverter P.C. board.
If signal stops between indoor
terminal block 2 and 3, replace
indoor P.C. board.
– 56 –
FILE NO. SVM-03008
Block distinction
Operation of diagnosis function
Air conditioner
Judgment and action
Check
Block
Check
code
Cause of operation
Remarks
code
status
Displayed when
error is detected.
Ondoor
P. C.
board
Inverter over-current
protective circuit operates.
(Short time)
All off
Even if trying operation again, all
operations stop immediately. :
Replace P.C. board.
Displayed when
error is detected.
Position-detect circuit error
or short-circuit between
windings of compressor
All off
1. Even if connecting lead wire of
compressor is removed, position-
detect circuit error occurred.
: Replace P.C. board.
2. Measure resistance between
wires of compressor, and perform
short circuit. : Replace
compressor.
Displayed when
error is detected.
Current-detect circuit error
All off
All off
Even if trying operation again, all
operations stop immediately. :
Replace P.C. board.
Displayed when
error is detected.
Being out of place,
disconnection or short-
circuit of outdoor temp.
sensor
1. Check outdoor temp. sensors
(TE, TS).
2. Check P.C. board.
Displayed when
error is detected.
Disconnection or short-
circuit of discharge temp.
sensor
All off
All off
1. Check discharge temp. sensor (TD).
2. Check P.C. board.
Displayed when
error is detected.
Outdoor fan drive system
error
Position-detect error, over-current
protective operation of outdoor fan
drive system, fan lock, etc. :
Replace P.C. board or fan motor.
–––
Not
displayed
Outdoor heat exchanger
temp. sensor error
Operation
continues.
1. Check outdoor heat exchanger
temp. sensor (TE).
2. Check P.C. board.
Displayed when
error is detected.
Ondoor
P. C.
board
Compressor drive output
error, Compressor error
(lock, missing, etc.),
Break down
All off
When 20 seconds passed after
startup, position-detect circuit error
occurred. : Replace compressor.
Flashes when
trouble is
Others
(including
compres-
sor)
Return serial signal has
been sent when operation
started, but it is not sent
from halfway.
(1) Compressor thermo.
operation
Gas shortage
Gas leak
(2) Instantaneous power
failure
Operation
continues.
1. Repeat Start and Stop with
interval of approx. 10 to 40
minutes. (Code is not displayed
during operation.)
Supply gas. (Check also gas leak.)
2. Unit operates normally during
check.
If return serial signal does not
stop between indoor terminal
block, 2 and 3 replace inverter
P.C. board.
detected on
return serial
signal, and
normal status
when signal is
reset.
If signal stops between indoor
terminal block, 2 and 3 replace
indoor P.C. board.
Displayed when
error is detected.
Compressor does not
rotate. (Current protective
circuit does not operate
when a specified time
passed after compressor
had been activated.)
All off
1. Trouble on compressor
2. Trouble on wiring of compressor
(Missed phase)
Discharge temp. exceeded
117°C
All off
All off
1. Check discharge temp. sensor (TD).
2. Degassing
3. Trouble on P.M.V.
Displayed when
error is detected.
Break down of compressor
1. Check power voltage. (220-240 V
+10%)
2. Overload operation of
refrigeration cycle
Displayed when
error is detected.
Check installation condition
(Short-circuit of outdoor diffuser.)
Four-way valve inverse error
(TC sensor value lowered
during heating operation.)
1. Check 4-way valve operation.
–––
Operation
continues.
– 57 –
FILE NO. SVM-03008
10-5. Judgment of Trouble by Every Symptom
10-5-1. Indoor unit (Including remote contro)
(1) Power is not turned on (Does not operate entirely)
<Primary check>
1. Is the supply voltage normal?
2. Is the normal voltage provided to the outdoor unit?
3. Is the crossover cable connected properly?
4. Is the fuse (F01) blown?
Operation
Check Item
Considerable principle cause
Turn off power supply once, and
5 second later, turn it on again.
Measures
Item by symptoms
NO
Is OPERATION lamp flashing?
YES
Does transmission mark
Is it possible to turn on
power supply by pushing
[START/STOP] button
on remote control?
NO
NO
on remote control flash
normally, and is its signal
transmitted properly?
Remote control is defective.
YES
YES
Refer to (5) Troubleshooting
for remote control .
Unit operates normally.
Does fan
YES
Is fuse (F01)
of indoor control
board blown?
YES
motor connector
between 1 and 2
short-circuit?
Parts (R01, R04, DB01, C01,
C03, IC01 and T01) are defective.
NO
NO
Is voltage
(DC12 V or 5 V)
indicated on rear of
indoor control
NO
YES
Microcomputer
is defective.
Replace main
P.C. board
board normal?
Is DC310-340 V
supplied to
primary side of
transfer switch?
NO
NO
Refer to <Primary check>
or this problem is one step
short of power P.C. board block.
YES
Transfer swith,
IC (IC01) for
power supply or
fan motor is
Are DC15 V, 12 V
and 7 V supplied to
secondary side of
transfer switch?
Are DC15 V, 12 V
NO
Turn off breaker once
and turn it on again
after removing motor.
and 7 V supplied to
secondary side of
transfeor switch?
defective.
YES
YES
Replace motor.
• Be sure to disconnect the motor connector CN10 after shut off the power supply, or it will be a cause of
damage of the motor.
– 58 –
FILE NO. SVM-03008
(2) Power is not turned on though Indoor P.C. board is replaced
<Confirmation procedure>
Turn on power supply.
NO
NO
Does operation
lamp flash?
Is wired connectly to white and black
lead wires of terminal block?
Correct wirng.
YES
YES
To item of Power supply
is not turned on .
– 59 –
FILE NO. SVM-03008
(3) Only indoor fan motor does not operate.
<Primary check>
(1) Is it possible to detect the power supply voltage (200 – 240 V) between 1 and 2 on the terminal block?
(2) Does the indoor fan motor operate in cooling operation?
(In heating operation, the indoor fan motor does not operate for approximately 5 minutes after it is turned on,
to prevent a cold air from blowing in.)
Turn off power
supply once, and
turn it on again.
Is it possible to detect
DC 1V or more between
5e and 3d of
YES
NO
Does fan motor
continue to operate?
Peplace indoor
fan motor.
motor connector (CN10).
NO
YES
Start to operate
indoor unit in cooling
operation at airflow
level LOW .
Is it possible to detect
DC 310−340 V between
1e and 3d of motor
connector (CN10).
NO
NO
Does indoor
fan operate?
YES
YES
Turn off indoor unit and remove
connector from motor.
Then push START/STOP button
on remote control to stop
(Motor connection condition)
NO
Is it possible to detect DC 15 V
between 4e and 3d of
motor connector (CN10).
flashing lamp on indoor unit.
YES
Is it possible to detect
DC 15 V between
4e and 3d of motor
connector (CN10).
NO
Peplace main
P.C. board.
Change airflow level
to HIGH .
YES
Start to operate the
indoor unit in except
heating operation.
Turn off indoor unit and
remove connector from motor.
Then start to operate indoor
unit with remote control.
NO
At this time, is it possible to
detect DC 1V or more between
5e and 3d of motor
connector (CN10)?
YES
Start to operate the
indoor unit in except
heating operation.
At this time, is it possible
to detect DC 1V or more
between 5e and 3d
of motor connector (CN10)?
(Check this condition
within 15 seconds after
starting unit.)
Is it possible to
change airflow level
to HIGH ?
NO
NO
YES
YES
Is it possible to
rotate cross-flow fan by
hand properly?
NO
NO
Peplace
bearing.
YES
Turn off indoor unit
and rotate cross-flow
fan by hand when the
unit is on standby.
At this time, is it possible
to detect DC 1V or more
between 5e and 3d
of motor connector
(CN10).
Fan motor
operates normally.
YES
– 60 –
FILE NO. SVM-03008
(4) Indoor fan motor automatically starts to rotate by turning on power supply.
<Cause>
The IC is built in the indoor fan motor. Therefore the P.C. board is also mounted to inside of the motor.
If the P.C. board is soldered imperfectly or the IC is defective, the fan motor may automatically rotate by turning
on power supply.
<Inspection procedure>
(1) Remove the front panel. (Remove 4 screws.)
(2) Remove the cover of the fan motor lead wires.
(3) Check DC voltage with CN10 connector while the fan motor is rotating.
NOTE:
• Do not disconnect the connector while the fan motor is rotating.
• Use a thin test rod.
Indoor fan starts rotating when power supply is turned on.
P.C. board
(Check output DC voltage of fan motor on P.C. board.)
CN10
6 (Blue)
Measure voltage between 2 (GND:BLACK)
and 3 (V line:YELLOW) of motor connector
(CN10) while indoor fan motor is rotating.
Yellow
Black
5 (Yellow)
4 (White)
3 (Black)
2 —
1 (Red)
DC 1.0 V or more
Under DC 1.0 V
DC
P.C. board is defective.
Replace P.C. board.
Motor is defective.
Replace motor.
– 61 –
FILE NO. SVM-03008
(5) Troubleshooting for remote control
The unit does not beep at all.
OPERATION lamp on
indoor unit is not indicated.
Press START/STOP
button.
NO
Is transmission
mark indicated?
YES
Press RESET button
on remote control
with tip of pencil.
Is receiver on
NO
indoor unit exposed
to direct sunlight?
YES
Does indoor unit
operate when
moving remote control
near receiver or
indoor unit?
Is there any
thyristor fluorescent
light nearby?
NO
NO
YES
Press START/STOP
button.
YES
Batteries are
exhausted.
Does indoor unit
NO
NO
Is transmission mark
indicated?
start to operate by
automatic restart
function?
YES
YES
NO
Does indoor unit
beep and operate?
YES
Does radio sound
is affected by
remote control when
a signal is transmitted
at distance of 5 cm
from radio?
NO
YES
Remote control
is defective.
P.C. board is
defective.
Avoid direct
sunlight.
Keep indoor unit
away from
Replace
batteries.
Normal
operation
Replace
remote control.
Replace
P.C. board.
thyristor
fluorescent light.
Note : After replacing batteries,
press the RESET button
with a tip of a pencil.
– 62 –
FILE NO. SVM-03008
10-5-2. Wiring Failure (Interconnecting and serial signal wire)
(1) Outdoor unit does not operate.
1) Is the voltage between indoor terminal block 2 and 3 varied?
Confirm that transmission from indoor to outdoor is correctly performed based on the following diagram.
NOTE:
• Measurement should be performed 2 minutes and 30 seconds after starting of the operation.
• Be sure to prepare a diode for judgment.
Terminal block on indoor side
Red
3
2
1
S5277G or equivalent (G or J type)
(Diode with rated voltage of 400 V
or more is acceptable.)
S5277G
White
Tester
Terminal block
Normal time
: Voltage swings between DC15 V and 60 V.
Abnormal time : Voltage does not vary.
(2) Outdoor unit stops in a little while after operation started.
<Check procedure> Select phenomena described below.
1) The outdoor unit stops 10 to 20 minutes after operation started, and 10 minutes or more are
required to restart the unit.
Gas shortage
Gas leak
Gas circulation amount is down.
Measure gas pressure.
Pipe clogging
Thermo operation of compressor
2) If the unit stops once, it dose not operate until the power will be turned on again.
To item of compressor does not operate.
3) The outdoor unit stops 10 minutes to 1 hour after operation started, and an alarm is displayed.
(Discharge temp. error check code 03, 1E Sensor temp. error check code 02, 1C)
Gas leak
P.M.V. is defective.
Refer to the chart in 10-6.
Miswiring of connecting wires of indoor/outdoor units
Clogging of pipe and coming-off TC sensor
– 63 –
FILE NO. SVM-03008
10-6. Check Code 1C (Miswiring in indoor/outdoor units) and 1E
<Check procedure>
1C
1E
Gas leakage,
Discharge temp. error,
gas leakage
(Check code 03, 1E)
disconnection of TS/TC
sensors (Check code 02, 1C)
Valve drive check
NO
NO
Is coil of the pulse modulation valve
(P.M.V.) correctly set?
Set it correctly.
Set it correctly.
YES
Is connector of coil connected to inverter?
YES
Is positioning sound of valve (sound hitting to stopper) heard from valve
when the air conditioner starts the operation after turning off power of the
air conditioner once?
NOTE :
After all the operations stopped by the remote control, the power keeps
being supplied to outdoor unit for approx. 3 minutes. If operating the air
conditioner by remote control again just after all the operations stopped by the
remote control, positioning of the valve is not performed when outdoor unit
is activated because supplying power to the outdoor unit is not interrupted.
After positioning of the valve, activate the compressor and the outdoor fan.
It takes approx. 7 seconds for positioning of the valve, and sound ticktack
(hitting sound to stopper) is heard for approx. 0.5 seconds at least of that
period. As the sound is low, check sound by using screwdriver, etc.
NO
Replace coil valve.
YES
Are temp. sensors of indoor/outdoor units correctly set to the holder?
NOTE :
The temperature sensors which are used to control electronic control valve
include indoor heat exchanger sensor (TC), outdoor heat exchanger temp.
sensor (TE), and outdoor suction temp. sensor (TS).
NO
Set it correctly.
YES
Gas amount check and valve clogging check
Remove TC sensor connector from the P.C. board in indoor unit.(Remove connector from the P.C. board.)
Operate the air conditioner in COOL mode by TEMP button ( Pi sound is heard if keeping pushed for 10 seconds.).
The operation enters temporary operation mode which fixes opening degree of P.M.V. and No. of revolution of
compressor. Check condensation at outlet of P.M.V., and then check operating pressure from the service port.
Existence of condensation at outlet of P.M.V.
YES
Replace valve.
Add gas.
If there is condensation at outlet (1/4 inch=∅6.35mm valve side),
the valve is clogged.
Check the operating pressure from service port, and add gas if pressure is low.
– 64 –
FILE NO. SVM-03008
10-7. How to Diagnose Trouble in Outdoor Unit
10-7-1. Summarized inner diagnosis of inverter assembly
Table 10-7-1
Diagnosis/Process flowchart
Item
Contents
Summary
Preparation
Turn “OFF” the power
breaker, and remove 3P
connector which connects
inverter and compressor.
• Check whether 25 A fuse
on the control board
assembly is blown or not.
(F01)
Remove
connector of
compressor.
Check
Check
If fuse was blown,
NG
be sure to check the
electrolytic capacitor
and diode block. (DB01)
• Connect discharge
resistance (approx.
Check 15 A fuse
(Part No.F01).
OK
Replace fuse.
100Ω40W) or soldering
iron (plug) between +, –
terminals of the electrolytic
capacitor (500µF)
of C14 (with printed
CAUTION HIGH VOLT-
AGE) on P.C. board.
Check
electrolytic
capacitor,
diode block
(DB01), etc.
Discharging position
(Discharging period
10 seconds or more)
Plug of
soldering
iron
Check
NG
terminal voltage
of electrolytic
capacitor.
Check
electrolytic
capacitor,
diode
OK
(DB01), etc.
Operation
Turn on power breaker, and
operate the air conditioner in
COOL mode by short-circuit
of the timer.
NO
Does outdoor
fan rotate?
YES
Measurement Measure terminal voltage of
electrolytic capacity.
YES
Does LED on control
board flash or go on?
OK if 500µF →
DC280 to 380 V
500µF: 400WV x 3
NO
Check
Stop
Remove CN300 by pushing
the part an arrow because
CN01 is a connector with
lock.
After operation, turn off the
power breaker after 2
minutes 20 seconds passed,
and discharge the electrolytic
capacity by soldering iron.
Check voltage between
motor phases.
Remove connector
CN300 of outdoor
fan motor, and using
a tester, check
resistance value
between every phase
at motor side
NG
Check
Measurement
• Is not winding
between 1-2, 2-3, or
1-3 opened or
OK
Replace
outdoor
fan motor.
short-circuited?
• Is not frame grounded with
1, 2 or 3?
→ Resistance between
phases should be approx.
55 to 77Ω.
A
B
C
→ Should be 10MΩ or
more.
– 65 –
FILE NO. SVM-03008
Diagnosis/Process flowchart
Item
Contents
Summary
Check
Check winding resistance
between phases of
A
B
C
compressor, and resistance
between outdoor frames by
using a tester.
• Is not grounded.
• Is not short-circuited
between windings.
Check
NG
→ OK if 10MΩ or more →
winding of
compressor.
OK if 0.51Ω → 0.57Ω
(Check by a digital tester.)
}
OK
• Winding is not opened.
Check
fan motor
position
detect
Replace
com-
NG
Operation
Remove connector CN300 of
the outdoor fan motor, turn on
the power breaker, and
perform the operation. (Stops
though activation is
pressor.
signal.
OK
Replace
outdoor
fan
prompted.)
Check operation within 2
minutes 20 seconds after
activation stopped.
motor.
<Output check of fan motor a) One or two of three
Replace control
board assembly.
position detect signal>
While connecting connector
5P (CN301) for position
detection, using a tester,
measure voltage between
1-5. Between 5-4 : 5 V
voltages should be 5 V,
and others should be 0V.
(When all are 0V or 5 V,
it is not accepted.)
Check
compressor
winding
b) When rotating the fan
slowly with hands, the
voltage between pins
should move from 0V to 5 V.
(Check it with an analog
tester.)
NG
resistance.
OK
Replace
control board.
Replace
compressor.
(2) Inspection procedures
10-8. How to Check Simply the Main Parts
1) When a P.C. board is judged to be defective,
check for disconnection, burning, or discolora-
tion of the copper foil pattern or this P.C. board.
2) The P.C. board consists of the following 2 parts
a. Main P.C. board part:
10-8-1. How to check the P.C. board (Indoor unit)
(1) Operating precautions
1) When removing the front panel or the P.C.
board, be sure to shut off the power supply
breaker.
2) When removing the P.C. board, hold the edge
of the P.C. board and do not apply force to the
parts.
3) When connecting or disconnecting the connec-
tors on the P.C. board, hold the whole housing.
Do not pull at the lead wire.
DC power supply circuit (5 V, 12 V, 15 V),
Indoor fan motor control circuit, CPU and
peripheral circuits, buzzer, and Driving circuit
of louver.
b. Indication unit of infrared ray receiving
Infrared ray receiving circuit, LED:
To check defect of the P.C. board, follow the
procedure described below.
– 66 –
FILE NO. SVM-03008
(3) Check procedures
Table 10-8-1
No.
Procedure
Check points (Symptom)
Causes
1
Turn off the power supply and
remove the P.C. board assembly
from electronic parts base. Remove
the connecting cables from the
terminal block.
Check whether or not the fuse (F01)
is blown.
Impulse voltage was applied or the
indoor fan motor short-circuited.
2
Remove the connector of the motor Check power supply voltage :
1. The terminal block or the cross-
over cable is connected wrongly.
2. The capacitor (C01), line filter
(L01), resistor (R01), or the diode
(DB01) is defective.
3. IC01, IC02 and T01 are defective.
4. IC01, IC02 and T01 are defective.
5. IC01, IC02, IC07 and T01 are
defective.
and turn on the power supply. If
OPERATION lamp flashes (once
per second), it is not necessary to
check steps (1 to 3) in the right
next column.
1. Between TP2 and TP3
(AC 220-240 V)
2. Between e and d (DC 310-340 V)
3. Between d of C10 and output side
of IC08 (DC 15 V)
4. Between 12 V and GND
5. Between 5 V and GND
3
4
Push [START/STOP] button once to Check power supply voltage :
start the unit. (Do not set the mode 1. Between CN23 and CN24
<Heating and cooling model>
IC03 and IC04 are defective.
to Fan Only or On-Timer operation.)
(DC 15-60 V)
Shorten the line of the restart delay Check whether or not all lamps
The lamps are defective or the
housing assembly (CN13) is
defective.
timer and start unit.
(OPERATION, TIMER, PRE. DEF,
FILTER and Hi POWER) are
indicated for 3 seconds and they
return to normal 3 seconds later.
5
Push [START/STOP] button once to 1. Check whether or not the
1. The temperature of the indoor
heat exchanger is extremely low.
2. The connection of the heat
exchanger sensor is loose.
(The connector is disconnected.)
(CN01)
3. The heat exchanger sensor and
the P.C. board are defective.
(Refer to Table 10-4-1.)
start the unit.
• Shorten the time of the restart
delay timer.
compressor operates.
2. Check whether or not the
OPERATION lamp flashes.
• Set the operation mode to COOL.
• Set the fan speed level to AUTO.
• Set the preset temperature much
lower than the room temperature.
(The unit (compressor) operates
continuously in the above
condition.)
4. The main P.C. board is defective.
6
If the above condition (No. 5) still
continues, start the unit in the
following condition.
1. Check whether or not the
compressor operates.
1. The temperature of the indoor
heat exchanger is extremely high.
2. Check whether or not the OPERA- 2. The connection of the heat
• Set the operation mode to HEAT.
• Set the preset temperature much
higher than room temperature.
TION lamp flashes.
exchanger sensor short-circuited.
(CN01)
3. The heat exchanger sensor and
the P.C. board are defective.
(Refer to Table 10-4-1.)
4. The main P.C. board is defective.
7
Connect the motor connector to the 1. Check it is impossible to detect the 1. The indoor fan motor is defective
motor and turn on the power supply.
Start the unit the following condition
• Set the operation mode to FAN.
• Set the fan speed level to HIGH.
(The unit (compressor) operates
continuously in the above
voltage (DC 15 V) between 3 and 4
of the motor terminals.
(Protected operation of P.C.
board.)
2. The motor does not operate. (But it 2. The connection or the motor
is possible to receive the signal
from the remote control.)
3. The motor rotates but vibrates
strongly.
connector is loose.
3. The P.C. board is defective.
condition.)
– 67 –
FILE NO. SVM-03008
10-8-2. P.C. board layout
GND
+12V
+5V
Bottom View
(For the Top View, refer to page 65.)
[1] Sensor characteristic table
100
90
80
TD
70
60
50
40
TD : Discharge temp. sensor
TA : Room temp. sensor
TC : Heat exchanger temp. sensor
TO : Outdoor temp. sensor
TE : Outdoor heat exchanger temp. sensor
TS : Suction temp. sensor
30
20
TA, TC, TO, TE, TS
10
0
0
10
20
30
40
50
Temperature (°C)
– 68 –
FILE NO. SVM-03008
10-8-3. Indoor unit (Other parts)
No.
Part name
Checking procedure
1
Room temp. (TA) sensor
Heat exchanger (TC) sensor
Disconnect the connector and measure the resistance value with tester.
(Normal temp.)
Temperature
10°C
20°C
25°C
30°C
40°C
Sensor
TA, TC (kΩ)
20.7
12.6
10.0
7.9
4.5
2
3
Remote control
To item of How to judge whether remote control is good or bad of the Judgment
of trouble by symptom.
Louver motor
MP24GA
Measure the resistance value of each winding coil by using the tester.
(Under normal temp. 25°C)
Position
Resistance value
1 to 2
1 to 3
1 to 4
1 to 5
380±40Ω
4
Indoor fan motor
Since judgment of DC motor is difficult on the single motor, refer to 10-5-1. (3)
10-8-4. Outdoor unit
No.
Part name
Checking procedure
1
Compressor
(Model : DA91A1F-45F)
Measure the resistance value of each winding by using the tester.
Red
Position
Red - White
White - Black
Black - Red
Resistance value
0.51 to 0.57Ω
White
Black
Under 20°C
2
Outdoor fan motor
Measure the resistance value of winding by using the tester.
(Model : ICF-140-43-1)
Position
Resistance value
5 to 20kΩ
Yellow - Pink
For details, refer to Section 10-9.
3
4
Compressor thermo. Bimetal type Check conduction by using the tester.
(Model : US-622KXTMQO-SS)
Outdoor temperature sensor
(TO), discharge temperature
sensor (TD), suction temperature
sensor (TS), outdoor heat
exchanger temperature sensor
(TE)
Disconnect the connector, and measure resistance value with the tester.
(Normal temperature)
Temperature
10°C
20°C
30°C
40°C
50°C
Sensor
TA, TC (kΩ)
105
64
41
27
18
TGa : Heat pump model only.
TO, TS, TE : Refer to the TA, TC characteristic table in Indoor
(Refer to Table 10-8-3, No.1).
– 69 –
FILE NO. SVM-03008
10-8-5. Checking Method for Each Part
No.
Part name
Checking procedure
1
Electrolytic capacitor
(For raising pressure, smoothing)
1. Turn OFF the power supply breaker.
2. Discharge all three capacitors completely.
3. Check that safety valve at the bottom of capacitor is not broken.
4. Check that vessel is not swollen or exploded.
5. Check that electrolytic liquid does not blow off.
6. Check that the normal charging characteristics are show in
continuity test by the tester.
Case that product is good
Pointer swings once, and
returns slowly. When
performing test once again
under another polarity, the
pointer should return.
C12, C13, C14 → 500µF/400V
2
Converter module
1. Turn OFF the power supply breaker.
2. Discharge all four capacitors completely.
3 Check that the normal rectification characteristics are shown in continuity
test by the tester.
−
−
Diode check
IGBT check
Tester rod
Tester rod
Resistance value
in good product
Resistance value
in good product
−
−
−
Ω
Ω
Ω
Ω
– 70 –
FILE NO. SVM-03008
10-9. How to Simply Judge Whether Outdoor Fan Motor is Good or Bad
1. Symptom
• Outdoor fan motor does not rotate.
• Outdoor fan motor stops within several ten seconds though it starts rotating.
• Outdoor fan motor rotates or does not rotate according to the position where the fan stopped., etc.
Remote controller check code “02 : Outdoor block, 1A : Outdoor fan drive system error”
2. Cause
The following causes are considered when the outdoor fan motor does not normally rotate.
1) Mechanical lock of the outdoor fan motor
2) Winding failure of the outdoor fan motor
3) Position-detect circuit failure inside of the outdoor fan motor
or
4) Motor drive circuit failure of the outdoor P.C. board
3. How to simply judge whether outdoor fan motor is good or bad
Turn OFF the breaker.
Disconnect two connectors (CN300 and CN301)
of the outdoor fan motor from the inverter.
NO
Does the fan rotate without trouble
when rotating it with hands?
YES
CN300
If the resistance value between
1 (Red lead)
2 (White lead)
3 (Black lead)
− 2 (White lead)
− 3 (Black lead)
− 1 (Red lead)
NO
of the connector
(CN300 : Motor winding)
is 17 to 25Ω, it is normal.
YES
If the resistance value between
1 (Yellow lead)
− 4 (Pink lead)
NO
CN301
of the connector
(CN301 : Motor position detection)
is 5k to 20kΩ, it is normal.
YES
Fan motor is normal.
Fan motor error
(Outdoor P.C. board error)
NOTE :
However, GND circuit error inside of the motor may be accepted in some cases when the above check is
performed.
When the fan motor does not become normal even if P.C. board is replaced, replace the outdoor fan motor.
– 71 –
FILE NO. SVM-03008
11. HOW TO REPLACE THE MAIN PARTS
11-1. Indoor Unit
No.
Part name
Procedures
Remarks
1
Front panel
How to remove the front panel
2
1) Stop operation of the air conditioner and turn off
its main power supply.
2
2
2) Pull the air inlet grille toward you to open it and
remove the air inlet grille.
Then remove the 4 screws fixing the front panel.
3) Open the horizontal louver, and then remove the
front panel from the back body by pulling it
toward you.
2 4-Screws
3
How to mount the front panel
Mount the front panel in position and make sure
all hooks are locked.
2
Electrical part
How to remove the electrical part.
1) Remove the front panel with the procedure 1.
2) Remove the screw holding the electrical part
cover.
2 Screws
3) Remove the drain guide.
4) Disconnect the connector (6P) for the fan motor
and the connector (5P) for the louver motor from
the P.C. board assembly.
3 Drain guide
5) Pull out the TC sensor from the sensor holder.
6) Remove each screw for the ground wire, the
electrical part box and the LED unit. Then
remove the LED unit and the electrical part box
from the main unit.
5 TC Sensor
How to mount the electrical part.
1) Fix the electrical part box by the upper hook of
the back body.
2) Tighten 2 screws on the electrical part box.
3) Connect the 2 connectors and arrange the
wiring same as original condition and then
tighten the screw to fix the LED unit to the back
body.
6 Screws
4
2-Connectors
4) Attach the TC sensor to the holder.
5) Tighten the screw for the ground wire.
6) Mount the drain guide (the TC sensor wire
should be covered with the drain guide).
7) Tighten the screw of the electrical part cover.
6 2-Screws
3
Horizontal louver
1) Remove the front panel and the electrical part
with the procedure 2.
2) Remove the center shaft of the horizontal louver
from the back body.
3) Remove the left shaft from the back body.
4) Remove the horizontal louver from the back
body.
3 Left shaft
2 Center shaft
– 72 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
4
Heat exchanger
1) Remove the front panel, electrical part and the
horizontal louver with the procedure 3.
2) Remove the pipe holder on the rear side of the
main unit.
3) Remove 2 screws of the heat exchanger on the
base bearing side.
4) Remove 2 screws of the heat exchanger on the
left side (upper and lower) from the back body,
and then pull out the upper side of the heat
exchanger slowly.
2 Pipe holder
3 2-Screws
4 2-Screws
5
Fan motor
1) Remove the front panel and the electrical part
with the procedure 2.
Mounting the fan motor as shown in
figure below.
2) Loosen the set screw of the cross flow fan.
3) Remove 2 screws fixing the motor band (R).
4) Pull out the fan motor.
Connector cover
Reference
line
Pull out the lead
wires of the fan motor
from this hole.
Reference line
When mouting the fan motor,
put the R end of the connector
cover this reference line.
– 73 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
1) Remove the front panel, electrical part,
horizontal louver and the heat exchanger with
the procedure 4.
6
Cross flow fan
2 2-Screws (R)
2) Remove 2 screws of the band motor (L) and
other 2 screws of the band motor (R) and then
remove the cross flow fan.
3) Loosen the set screw of the cross flow fan then
disconnect the fan and the fan motor.
2 2-Screws (L)
Notice
4.5 mm
For position of the fan motor connector and
drawing out of the lead cables, refer to the
procedure 5.
Fix the cross flow fan with the set screw at the
position where the gap between the back body and
the right surface of the cross flow fan is 4.5 mm.
3 Set screws
1) Remove the front panel, electrical part,
horizontal louver, heat exchanger and the cross
flow fan with the procedure 5 and 6 .
2) Remove the 2 screws fixing the base bearing.
3) Remove the bearing from the base bearing.
If the housing protrudes from the base bearing,
put the housing in position and attach the
bearing to the base bearing.
7
Base bearing
2 2-Screws
– 74 –
FILE NO. SVM-03008
11-2. Microcomputer
No.
Part name
Procedures
Remarks
1
Common
procedure
1) Turn the power supply off to stop the operation
of air conditioner.
2) Remove the front panel.
Replace the thermal fuse, terminal
block, microcomputer ass’y and the
P.C. board ass’y
• Remove the 4 fixing screws.
3) Remove the electrical part base.
<P.C. board layout>
R04
CN10
Fuse
C01
CN13
RY01
DB01
L01
IC03
IC02
CN04
R05
C03
Top View
T01
IC01
C02
R01
– 75 –
FILE NO. SVM-03008
11-3. Outdoor Unit
No.
Part name
Procedures
Remarks
1. Detachment
1
Common
procedure
Upper cabinet
Wiring cover
1) Stop operation of the air conditioner, and turn off
the main switch of the breaker for the air
conditioner.
2) Remove the valve cover. (ST1T∅4 x 10s 1 pc.)
• After removing screw, remove the valve cover
pulling it downward.
Valve cover
3) Remove wiring cover (ST1T∅4 x 10s 2 pcs.),
and then remove connecting cable.
4) Remove the upper cabinet.
(ST1T∅4 x 10s 2 pcs.)
• After removing screws, remove the upper
cabinet pulling it upward.
2. Attachment
1) Attach the upper cabinet.
(ST1T∅4 x 10s 2 pcs.)
• Hook the rear side of the upper cabinet to
claw of the rear cabinet, and then put it on the
front cabinet.
2) Perform cabling of connecting cable, and attach
the wiring cover.
• Insert the upper part into the upper cabinet,
insert claw which has been hooked to the
lower part into the square hole, and then fix it
with screw. (ST1T∅4 x 10s 1 pc.)
3) Attach the valve cover. (ST1T∅4 x 10s 1 pc.)
• Insert the upper part to the upper cabinet,
set hook claw of the valve cover to square
holes (at three positions) of the main unit,
and attach it pushing upward.
2
Front cabinet
1. Detachment
1) Perform work of item 1 of 1.
2) Remove screw (ST1T∅4 x 10s 2 pc.) of the
front cabinet and inverter cover and screws
(ST1T∅4 x 10s 3 pcs.) of the front cabinet and
lower part.
• The left side of the front is made to insert to
the rear cabinet, so remove it pulling upward.
2. Attachment
1) Insert claw at the left side of the front into the
rear cabinet.
Claw
2) Hook the lower part at the right side of the front
to concave part of the bottom plate. Insert claw
of the rear cabinet into square hole of the front
cabinet.
Square hole
3) Attach the removed screws to the original
positions.
Concave section
– 76 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
3
Inverter
assembly
1) Perform work of item 1 of 1.
2) Remove screw (ST1T∅4 x 10s 2 pc.) of the
upper part of the front cabinet.
Inverter cover
P. C. board
(Soldered surface)
• If removing the inverter cover in this condition,
P.C. board can be checked.
• If there is no space in the upper part of the
upper cabinet, perform work of 2.
Be careful to check the inverter because
high-voltage circuit is incorporated in it.
3) Perform discharging by connecting e, d
polarity by discharging resistance (approx.
100Ω40W) or plug of soldering iron to e, d
terminals of the C14 (printed “CAUTION HIGH
VOLTAGE” is attached.) electrolytic capacitor
(500 µF) on P.C. board.
Plug of
soldering
iron
Discharging position
(Discharging period
10 seconds or more)
Be careful to discharge the capacitor
because the electrolytic capacitor cannot
naturally discharge and voltage remains
according to trouble type in some cases.
NOTE :
This capacitor is one with mass capacity.
Therefore, it is dangerous that a large
spark generates if short-circuiting
between the e,d polarity with screw-
driver, etc. for discharging.
Bundled
part
4) Remove screw (ST1T∅4 x 10s 2 pc.) fixing the
main body and the inverter box.
5) Remove various lead wires from the holder at
upper part of the inverter box and wiring holder
at right side of the terminal block.
Holder
6) Remove the lead wire from the bundled part at
left side of the terminal block.
Terminal block
7) Pull the inverter box upward.
8) Disconnect connectors of various lead wires.
The connector is one
Requirement :
with lock, so remove it
while pushing the part
indicated by an arrow.
As each connector has a lock
mechanism, avoid to remove the
connector by holding the lead wire,
but by holding the connector.
Be sure to remove the connector by
holding the connector, not by pulling
the lead wire.
– 77 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
4
Control board
assembly
1) Disconnect lead wires and connectors
connected from the control board
assembly to other parts.
CN701
CN703 CN602
CN301
CN300
CN500
1. Lead wires
CN603
• Connection with terminal block :
3 wires (Black, White, Orange)
• Connection with compressor :
Remove the connector (3P)
CN601
CN600
• Connection with reactor :
CN300, CN301 and CN701, etc. at the
control board assembly side are
connectors with locks. Therefore,
remove the connector while pushing
the part indicated by an arrow.
Remove the relay connectors from P07, 08
(2P, White) and P12, 13 (2P, Yellow).
2. Connectors
CN300 : Outdoor fan (3P, White)
CN301 : Outdoor fan position detection
(5P, White)
CN701 : 4-way valve (3P, Yellow)
CN600 : TE sensor (2P, White)
CN601 : TD sensor (3P, White)
CN603 : TS sensor (3P, White)
CN602 : TO sensor (2P, White)
CN500 : Case thermo. (2P, White)
CN703 : Pulse modulating valve
(6P, White)
2) Remove the control board assembly from
P.C. board base.
1. Main control board assembly side
• Remove two claws of P.C. board base, and
remove upward the heat sink with hands.
• Remove three screws fixing the heat sink
and main control board assembly side, and
replace the board with a new one.
P.C. board base
P.C. board
When mounting a new board, check
that the board is correctly set in the
groove of base holder of P.C. board
base.
5
Rear cabinet
1) Perform work of item 1 of 1, 1 and 2, 3.
2) Remove fixed screws fixing to the bottom plate.
(ST1T∅4 x 10s 3 pcs.)
Reactor
3) Remove fixed screws fixing to the heat
exchanger. (ST1T∅4 x 10s 2 pcs.)
4) Remove fixed screw fixing to the valve mounting
plate. (ST1T∅4 x 10s 1 pc.)
– 78 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
6
Fan motor
1) Perform work of item 1 of 1 and 2.
2) Remove the flange nut fixing the fan motor and
the propeller fan.
Fan motor
Propeller fan
• Flange nut is loosened by turning clockwise.
(To tighten the flange nut, turn counterclock-
wise.)
3) Remove the propeller fan.
4) Disconnect the connector for fan motor from the
inverter.
5) Remove the fixing screws (3 pcs.) holding by
hand so that the fan motor does not fall.
Flange nut
7
Compressor
1) Perform work of item 1 of 1 and 2, 3, 4, 5.
2) Extract refrigerant gas.
3) Remove the partition board.
(ST1T∅4 x 10s 2 pcs.)
4) Remove the sound-insulation material.
5) Remove the terminal cover of the
compressor, and disconnect lead wire of the
compressor thermo. and the compressor from
the terminal.
Valve
clamping
plate
Partition
board
6) Remove pipe connected to the compressor with
a burner.
7) Remove the fixing screw of the bottom plate
and heat exchanger.
Compressor
thermo.
(ST1T∅4 x 10s 2 pc.)
8) Remove the fixing screw of the bottom plate
and valve clamping plate.
Compressor
(ST1T∅4 x 10s 2 pcs.)
9) Pull upward the refrigeration cycle.
10) Remove the nut fixing the compressor to the
bottom plate.
8
Reactor
1) Perform work of item 1 of 1 and 3.
2) Remove lead wires clung in holder on the
partition board.
Reactor
3) Remove the screw fixing the reactor.
(ST1T∅4 x 10s 2 pcs.)
– 79 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
9
Pulse modulating
valve coil
1. Detachment
1) Perform work of item 1 of 1, and 2, 3, 5.
2) Turn the coil clockwise (counterclockwise) by
90 degrees, and remove coil from the pulse
modulating valve.
Take-out part
of lead wire
2. Attachment
1) Set take-out part of the lead wire of coil to the
coil inserting position of the pulse modulating
valve, and attach the coil.
2) Turn the coil by 90 degrees, set surely the
concave part at lower part of the coil to the
positioning hole of the pulse modulating valve,
and then fix the coil.
Notch
Coil fix
position
Coil inserting
position
The pulse modulating valve has A room
side and B room side. After mounting it,
check that coil at B room side (Red
marking is marked on the pulse modulat-
ing valve.) is connected to CN13 of the
control board assembly.
Coil inserting
position
Positioning
hole
!
Fan guard
1. Detachment
1) Perform work of item 1 of 1, and 2.
2) Remove the front cabinet, and put it down so
that fan guard side directs downward.
Perform work on a corrugated cardboard,
cloth, etc. to prevent flaw to the product.
3) Remove the hooking claws by pushing minus
screwdriver according to the arrow mark in the
right figure, and remove the fan guard.
Minus screwdriver
Hooking claw
2. Attachment
1) Insert claw of the fan guard in the hole of the
front cabinet. Push the hooking claws
(10 positions) by hands and fix the claws.
All the attaching works have completed.
Check that all the hooking claws are fixed
to the specified positions.
– 80 –
FILE NO. SVM-03008
No.
Part name
Procedures
Remarks
"
Replacement of
temperature
sensor for
1) Cut the sensor 100 mm longer than old one.
2) Cut the protective tube after pulling out it
(200 mm).
Cutting here
100
Thermal
sensor part
Connector
servicing only
3) Move the protective tube toward the thermal
sensor side and tear the tip of lead wire in two,
then strip the covering part.
Cutting here
200
4) Pass the stripped part through the thermal
constringent tube.
5) Cut the old sensor 100 mm length on the
connector side, and recycle that connector.
6) Tear the lead wire in two on the connector side
and strip and covering part.
Common service
parts of sensor
TO, TS, TE, TD
Thermal
constringent tube
7) Twist the leads on the connector and sensor
sides, and solder them.
8) Move the thermal constringent tubes toward
the soldered parts and heat them with the
dryer and constring them.
Cutting here
100
9) Wind the attached color tape round the both
terminals of the protective tube when colored
protective tube is used.
10) Fix the sensor again.
Soldered part
NOTES:
1) Store the joint part of the sensor and the
connector in the electric parts box.
2) Never joint them near the thermal sensor part.
Otherwise, it would cause insulation inferiority
because of dew drops.
3) When replacing the sensor using the colored
protective tube, wind the color tape matching
the color of that tube.
Dryer
Winding the color tape
These are parts for
servicing sensors.
Part name
Q’ty
Remarks
1
2
3
4
5
6
Sensor
1
1
1
3
1
3
Length: 3 m
Please check that
the accessories
shown in the right
table are packed.
Sensor Spring (A)
Sensor Spring (B)
Thermal constringent tube
Color tape
For spare
For spare
Including one spare
9 colors
Terminal
– 81 –
FILE NO. SVM-03008
<P.C. board layout>
MCC-813
– 82 –
FILE NO. SVM-03008
12. EXPLODED VIEWS AND PARTS LIST
12-1. Indoor Unit (E-Parts Assy)
405
406
403
402
404
401
Location
No.
Part
No.
Location
No.
Part
No.
Description
Description
401
402
403
43T69319 Temperature Sensor, TC 10kΩ 25°C
43T60001 Terminal, 2P AC300V, 20A
404
405
406
43T62003 Cord Clamp
43169079 P.C. Board ASSY, WRS-LED
43T69322 P.C. Board, MCC-867
43T69320 Temperature Sensor, TA 10kΩ 25°C
– 83 –
FILE NO. SVM-03008
12-2. Indoor Unit
217
216
217
214
210
211
218
225
208
215
203
212
219
220
201
205
207
204
233
222
223
224
202
221
209
231
232
Electric Parts
Assembly
226
227
229
228
204
234
206
Location
No.
Part
No.
Location
No.
Part
No.
Description
Description
201
202
203
204
205
206
207
208
209
210
211
212
214
215
216
217
43T00366 Front Panel Assy
43T09316 Inlet Grille Assy
43T03302 Back Body Assy
43T80301 Air Filter
218
219
220
221
222
223
224
225
226
227
228
229
231
232
233
234
43T79302 Guide Drain
43T22002 Bearing
43T39301 Base, Bearing
43T20302 Cross Flow Fan
43T39302 Band Motor-L
43T09309 Horizontal Louver
43T08350 LED Panel Assy
43T70002 Drain Hose
43T21327 Motor, Fan, ICF-340-30-2, DC 340V
43T39303 Band Motor-R
43T82301 Plate, Installation
43T69306 Remote Control
43T83003 Holder Remote Control
43T85325 Owner’s Manual
43T62302 Terminal Cover
43T60317 Cord Motor Louver
43T60316 Cord Motor Fan
43T07303 Holder Pipe
43T79301 Cap Drain
43T21321 Motor, Louver, MP24GA, DC 12V
43T44320 Refrigeration Cycle Assy
43T47006 Pipe, Delivery ∅6.35
43T47305 Pipe, Suction ∅8.00
43T11301 Pipe Shield
43T19302 Holder Sensor
43T49302 Plate of EVA Seal
43T49006 Holder, Plate EVA Seal
43T01003 Mark
– 84 –
FILE NO. SVM-03008
12-3. Outdoor Unit
Location
No.
Part
No.
Location
No.
Part
No.
Description
Description
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
43T00377 Cabinet, Front, Assy
43T00381 Cabinet, Back, Assy
43T42304 Base, Assy
16
17
18
19
20
21
22
23
24
25
26
27
28
29
43T46326 Body-PMV
43T63305 Coil-PMV
43T58303 Reactor
43T00380 Cabinet, Upper, Assy
43T09318 Guard, Fan
43T54304 Thermostat, Bimetal
43T63005 Holder, Thermostat, Bimetal
43T20307 Fan, Propeller
43T21334 Motor, Fan
43T52310 Cover, Packed Valve
43T62311 Cover, Wiring, Assy
43T41336 Compressor
43T47001 Nut, Flange
43T43330 Condenser, Assy
43T46317 Valve, Packed 6.35 Dia.
43T46320 Valve, Packed 9.52 Dia.
43T47020 Bonnet, 6.35 Dia.
43T47021 Bonnet, 9.52 Dia.
43T03303 Fixing Plate Valve, Assy
43T47008 Tube, Capillary
42T47324 Bolt, Compressor (M6)
43T49308 Cushion, Rubber
43T46323 Valve, 4-way
43T63304 Coil, 4-way, Assy
43T63306 Holder, Sensor
43T79305 Nipple, Drain
– 85 –
FILE NO. SVM-03008
12-4. Outdoor Unit (E-Parts Assy)
701
704
702
706
TE Sensor (∅6)
TS Sensor (∅6)
TO Sensor (∅6)
707
TD Sensor (∅4)
705
703
3
2
1
4
3
2
1
Location
No.
Part
No.
Location
No.
Part
No.
Description
Description
701
702
703
704
43T62312 Heatsink
43T69345 P.C. Board
43T60027 Terminal 6P
43T60326 Fuse
705
706
707
43T50305 Temperature Sensor
43T50304 Temperature Sensor
43T62313 Base-Plate-P.C.
– 86 –
T O S H IB A C A R R IE R C O R P O R A T IO N
|