Samsung Db98 17032a 5 User Manual

OWNER'S  
INSTRUCTIONS  
AW0605B AW0695B  
AW0805B AW0895B  
AW1005B  
AW109BB  
AW089DB  
AW1095B  
AW109DB AW1205B  
AW129BB  
AW1295B  
AW129DB  
Window-type Room Air Conditioner  
(Cool)  
E
F
DB98-17032A(5)  
Safety Precautions  
The following safety precautions must be taken when using your air conditioner.  
Risk of electric shock. Can cause injury or death. Disconnect all  
WARNING  
remote electric power supplies before servicing, installing or cleaning.  
This must be done by the manufacturer or its service agent or a similar  
qualified person in order to avoid a hazard.  
Users of this product are cautioned not to attempt repair of this product at their  
own discretion. Instead, they are requested to directly contact a designated  
service center or the outlet at which the product was purchased.  
DURING OPERATION  
Never spill any kind of liquid into the unit. Should this happen, unplug or main  
switch off the unit and contact an authorized service center.  
Do not insert anything between the air outlet blades because the inner fan may  
be damaged and could cause injury. Keep children away from the unit.  
Do not place any obstacles in front of the unit.  
Do not spray liquid of any kind into the indoor unit. Should this happen, switch off  
the breaker used for your air conditioner and contact your installation specialist.  
Make sure that the unit is correctly ventilated at all times:  
Do not place clothing or other materials over it.  
If the wireless remote control will not be used for a long time, remove the  
batteries. (If applicable)  
When using a wireless remote control, the distance should not be more than 7  
meters from the air conditioner. (If applicable)  
The air conditioner must be plugged into its own specific power source, which  
must be installed in compliance with national wiring,earthing and safety  
regulations.  
If the power cord is damaged in any way, it must be replaced by the manufacturer  
or its service agent or a similarly qualified person in order to avoid a hazard.  
This device must be installed according to the national electrical rules.  
The appliance must be installation that the plug should be easily accessible  
after installation.  
If the fuse on PC board is broken please change it with the type of T 3.15A 250V.  
The breaker of the air conditioner should be all-pole switch; and the distance  
between its two contacts should be no less than 3.5mm. Such means for  
disconnection must be incorporation in the fixed wiring.  
Before throwing out the device, it is necessary to pull back the battery cells and  
get rid of them safely for recycling reasons.  
DISPOSING OF THE UNIT  
When you need to dispose of the unit, consult your dealer. If pipes are removed  
incorrectly, refrigerant may blow out and come into contact with your skin,causing  
injury. Releasing refrigerant into the atmosphere also damages the environments.  
Please recycle or dispose of the packaging material for this product in an  
environmentally responsible manner.  
Never store or ship the air conditioner upside down or sideways to avoid damage  
to the compressor.  
OTHERS  
The appliance is not intended for use by young children or infirm persons without  
supervision: Young children should be supervised to ensure that they do not play  
with the appliance.  
Max current is measured according to IEC standard for safety and current is  
measured according to ISO standard for energy efficiency.  
E-2  
Contents  
PREPARING YOUR AIR CONDITIONER  
Safety Precautions .........................................................................................  
Description of Each Component ....................................................................  
Remote Control - Buttons ..............................................................................  
Getting Started ...............................................................................................  
Inserting the Remote Control Batteries ..........................................................  
2
4
5
6
7
OPERATING YOUR AIR CONDITIONER  
Cooling Your Room ........................................................................................  
Airing Your Room ...........................................................................................  
8
9
Removing Excess Humidity ............................................................................ 10  
Adjusting the Air Flow Direction Horizontally .................................................. 11  
Adjusting the Air Flow Direction Vertically ...................................................... 11  
PROGRAMMING YOUR AIR CONDITIONER  
Setting the On Timer ...................................................................................... 12  
Setting the Off Timer ...................................................................................... 13  
Setting the Sleep Timer .................................................................................. 14  
Selecting Energy Saving mode ...................................................................... 15  
RECOMMENDATIONS FOR USE  
Temperature and Humidity Ranges ................................................................ 16  
Cleaning Your Air Conditioner ........................................................................ 17  
Solving Common Problems ............................................................................ 18  
Technical Specifications ................................................................................. 19  
E-3  
Description of Each Component  
The design and shape are subject to  
change.  
Air outlet  
Outer air flow blades  
(up/down orientation)  
Inner air flow  
blades (right/left  
orientation)  
Air outlet  
Ventilation lever  
Air inlet (Inside)  
Air inlet (Outside)  
Air filter (Inside)  
Power plug  
(The type of power plug  
may differ, depending on  
the local power supply.)  
Temperature/Timer  
settings  
Mode selection button  
(Cool,Fan, Dry)  
Energy Saver button  
Temperature adjustment  
buttons  
Sleep timer setting button  
Timer setting button  
On/Off button  
Fan speed adjustment button Remote control  
E-4  
Remote Control - Buttons  
Timer setting button  
Temperature  
adjustment buttons  
Sleep timer setting  
button  
Mode selection  
buttons  
Fan speed  
adjustment buttons  
Energy Saver button  
On/Off button  
E-5  
Getting Started  
Your Ow ners Instructions contain much valuable information on using your air conditioner.  
Please take the time to read them as they w ill help you take full advantage of the units features.  
The booklet is organized as follow s.  
The follow ing figures are show n on pages 4 and 5:  
-
-
Description of Each Component  
Remote control (buttons)  
They w ill help you find the buttons and understand the symbols displayed.  
In the manual, you w ill find a series of step-by-step procedures for each function avai-  
lable.  
The illustrations in the step-by-step procedures use four different symbols:  
NOTE  
PRESS  
PUSH  
IMPORTANT  
E-6  
Inserting the Remote Control Batteries  
You m ust insert or replace the rem ote control batteries w hen :  
You purchase the air conditioner  
The rem ote control does not w ork correctly  
Use two AAA, LR03 1.5V batteries.  
Do not use old batteries or different kinds of batteries together.  
Batteries may be completely discharged after 12 months, even  
if they have not actually been used.  
1
2
Push the battery cover on the rear of the remote control with your thumb  
in the direction of the arrow and remove it.  
Insert the two batteries, taking care to respect the polarities :  
+ on the battery with + on the remote control.  
- on the battery with - on the remote control.  
3
Close the cover by sliding it back until it clicks into place.  
E-7  
Cooling Your Room  
You must select the Cool mode if you wish to lower the temperature  
in your room. You can also set the Fan speed.  
Remote Control  
Control Panel  
Press the  
Result:  
(On/Off) button.  
The air conditioner starts up in the Cool mode.  
1
The unit beeps twice.  
The air conditioner is fitted with a protection mechanism to prevent  
the unit from being damaged when it is started immediately after  
being:  
Plugged in  
Stopped  
It will begin to cool after three minutes.  
2
If the temperature is not displayed on the control panel:  
Press the  
or  
Press the  
button on the remote control  
is displayed.  
button.  
button on the unit one or more times until  
Result:  
The unit beeps each time you press the  
/
The air conditioner starts up in the Cool mode.  
You can change modes at any time.  
3
To adjust the temperature, press the  
or  
buttons on the remote  
control or unit one or more times until the desired temperature is displayed.  
The temperature can be set between 18 C and 30 C.  
Result:  
Each time you press the  
or  
buttons:  
- The temperature is adjusted by 1 C and displayed on  
the control panel  
- The unit beeps  
The air conditioner starts cooling, if the room temperature is  
higher than the selected temperature.  
If the room temperature reaches the set temperature, the air  
conditioner stops cooling, but the fan is still operating.  
4
5
To set the fan speed:  
Press the  
,
or  
button on the remote control as desired.  
or  
Press the  
button on the unit one or more times until the  
desired Fan speed(F1, F2 or F3) is displayed.  
To control the direction of the air flow, refer to page 11.  
E-8  
Airing Your Room  
If you want to provide air circulation without cooling, you can use  
the Fan mode.  
Remote Control  
Control Panel  
1
If necessary, press the  
(On/Off) button.  
Result:  
The air conditioner starts up in the Cool mode  
.
The unit beeps twice.  
2
If the fan speed(F1, F2 or F3) is not displayed on the control panel:  
Press the  
button on the remote control  
or  
Press the  
button on the unit one or more times until the fan speed  
(F1, F2 or F3) is displayed.  
Result: The unit beeps each time you press the  
/
button.  
The air conditioner starts up in Fan mode.  
You can change modes at any time.  
When the air conditioner is in the Fan mode, the temperature  
cannot be set or displayed.  
3
To set the fan speed:  
Press the  
,
or  
button on the remote control as desired.  
or  
Press the  
button on the unit one or more times until the  
desired fan speed(F1, F2 or F3) is displayed.  
4
To control the direction of the air flow, refer to page 11.  
E-9  
Removing Excess Humidity  
If the atmosphere in your room is very humid or damp, you can remove  
excess humidity without lowering the room temperature too much.  
Remote Control  
Control Panel  
1
If necessary, press the  
(On/Off) button.  
Result:  
The air conditioner starts up in the Cool mode.  
The unit beeps.  
The air conditioner is fitted with a protection mechanism to pre-  
vent the unit from being damaged when it is started immediately  
after being:  
Plugged in  
Stopped  
It will begin to cool after three minutes.  
2
If the temperature is not displayed at the top of the control panel, press  
the  
button on the control panel one or more times until it  
appears.  
Result:  
The unit beeps each time you press the  
The air conditioner runs in Dry mode.  
button.  
You can change modes at any time.  
3
To adjust the temperature, press the  
or  
buttons one or  
more times until the required temperature is displayed.  
Possible temperatures are between 18 C and 30 C inclusive.  
Result:  
Each time you press the  
or  
buttons:  
- The temperature is adjusted by 1 C  
- The unit beeps  
The air conditioner starts removing the excess humidity;  
the quantity of air is adjusted automatically.  
4
To control the direction of the air flow, refer to page 11.  
E-10  
Adjusting the Air Flow Direction Horizontally  
Depending on the position of the unit in your room, you can adjust  
the orientation of the inner air flow blades on the unit.  
Adjust the air flow blades to the desired position by pushing them side to side.  
Adjusting the Air Flow Direction Vertically  
The outer air flow blades can be adjusted to control the vertical air  
flow direction.  
RECOMMENDATION When...  
Adjust the blades to face...  
Cooling  
Upwards.  
Adjust the air flow blades to the desired position, by pushing them  
upwards or downwards.  
If you orient the air flow blades downwards and the unit operates  
in Cool mode for long periods of time, dew may:  
-
-
Form on the surface of the blades  
Drip from the blades  
E-11  
Setting the On Timer  
The On Timer enables you to switch on the air conditioner automatically after a  
given time. You can select the On timer only when the air conditioner is off.  
Remote Control  
Control Panel  
1
Check that the air conditioner has been switched off; if necessary,  
press the (On/Off) button.  
2
Set the operating time by pressing the  
or button on the unit one or more times until the desired time is dis-  
played. The operating time can be set between 1 and 24 hours.  
button on the remote control  
Result:  
Each time you press the  
button:  
- The time is adjusted by 1 hour and displayed on the control  
panel  
- The unit beeps  
The operating time is displayed and decreases automatically to  
indicate the remaining time.  
The air conditioner starts up in the Cool or Dry mode automati-  
cally when the operating time reaches zero.  
To Cancel the On Timer  
To cancel the timer, press:  
Timer on the remote control or unit one or more times until "--" is displayed.  
or  
The  
(On/Off) button on the remote control or unit (The air conditioner  
operates in the mode selected when the unit was last used.)  
E-12  
Setting the Off Timer  
The Off Timer enables you to switch off the air conditioner automatically after a  
given time. You can select the Off timer only when the air conditioner is on. You  
can select the Off timer when the air conditioner operates in the Cool or Dry mode.  
Remote Control  
Control Panel  
1
Check that the air conditioner has been switched on; if necessary,  
press the (On/Off) button.  
2
Set the operating time by pressing the  
or button on the unit one or more times until the desired time is dis-  
played. The operating time can be set between 1 and 24 hours.  
button on the remote control  
Result:  
Each time you press the  
button:  
- The time is adjusted by 1 hour and displayed on the control  
panel  
- The unit beeps  
The operating time is displayed and decreases automatically to  
indicate the remaining time.  
The air conditioner switches off automatically when the  
operating time reaches zero.  
You can select the fan speed, temperature and Energy saving mode  
after setting the On timer and Off timer mode. However, when you  
change the mode, the On timer and Off timer mode is canceled.  
To Cancel the Off Timer  
To cancel the timer, press:  
Timer on the remote control or unit one or more times until "--" is displayed.  
or  
The  
(On/Off) button on the remote control or unit.  
E-13  
Setting the Sleep Timer  
The Sleep Timer can be used when you are cooling your room to switch  
the air conditioner off automatically after 8 hours.  
If you wish to switch the unit off at a specific time, refer to page 13.  
Remote Control  
Control Panel  
1
Make sure that you have selected the Cool mode.  
2
Press the  
or  
Press the  
button on the remote control  
button on the unit.  
Result:  
Each time you press a button, the unit beeps.  
The " " will be displayed.  
The remaining time is displayed and decreased by 1 hour  
automatically to indicate the remaining time.  
The air conditioner will be controlled as illustration below.  
Cooling When the temperature has  
been increased by 1 C  
(after 1 hour), it is maintained  
for 7 hours.  
To Cancel the Sleep Timer  
To cancel the timer, press:  
Sleep on the remote control.  
or  
Sleep on the unit.  
Result:  
The unit beeps.  
The SLEEP indicator is no longer displayed.  
The air conditioner operates in the mode selected last.  
If you select the Energy Saving mode in the Sleep Timer mode,  
the Sleep Timer will be cancelled and the air conditioner will start up  
in the Energy Saving mode.  
E-14  
Selecting Energy Saving Mode  
If you wish to save energy when using your air conditioner,  
select the energy saving mode.  
Remote Control  
Control Panel  
To select the energy saving mode, press the  
control or button on the unit one or more times until the Energy  
Saver indicator lights up.  
button on the remote  
1
Result:  
The fan and compressor cycle on and off together.  
The fan will continue to run for a short time after the  
compressor cycles off.  
If you would like the air conditioner to run in Dry mode, do not press  
the  
button. You cannot use the Dry mode in the energy saving  
mode.  
2
To stop the energy saving mode, press the  
control or button on the unit again.  
button on the remote  
Result: The fan runs at all times, while the compressor cycles on and off.  
If you select the Sleep Timer in the Energy Saving mode, the Energy  
Saving will be cancelled and the air conditioner will start up in the  
Sleep Timer mode.  
E-15  
Temperature and Humidity Ranges  
The follow ing table indicates the temperature and humidity ranges  
w ithin w hich the air conditioner can be used.  
Mode  
Indoor Temperature  
Outdoor Temperature  
Indoor Humidity  
Cooling  
21°C to 32°C approx.  
21°C to 43°C approx.  
80% or less  
If the air conditioner is used at...  
Then...  
Higher temperature  
The automatic protection feature may be triggered and the air  
conditioner stopped.  
Lower temperature  
A water leakage or some other malfunction may happen if the  
heat exchanger freezes.  
Higher humidity levels  
Water may condense on and drip from the surface of the unit  
if it is used for long periods.  
E-16  
Cleaning Your Air Conditioner  
Be sure to clean the air filter periodically to maintain the air conditioner  
in the best condition for a long period of time.  
When cleaning the air conditioner, turn it off and pull out the  
power plug.  
1
Open the front grille by pulling the tabs on both sides of the grille.  
Then lift it up slightly to open the front grille completely.  
2
3
Grab the tabs on the filter and pull it up and out.  
Remove all dust on the air filter with a vacuum cleaner or brush.  
4
5
When you have finished, insert the air filter back into its original position.  
Wipe the surface of the unit with a neutral detergent and then wipe it again  
with dry cloth. (Be sure not to use benzene, solvent or other chemical  
products.)  
If you...  
Then...  
Set the fan going for a few  
hours to dry the inside of the air  
conditioner thoroughly.  
Will not be using the  
air conditioner for a  
long period of time  
Switch the air conditioner off and  
unplug it from the wall socket.  
Clean the filter and outer surfaces.  
Set the fan going for a few hours to dry  
the inside of the air conditioner tho-  
roughly.  
Have not used the air  
conditioner for a long  
period of time  
E-17  
Solving Common Problems  
Before contacting an authorized service center, perform the follow ing sim ple checks.  
They m ay save you the tim e and expense of an unnecessary call.  
Problem  
Explanation / Solution  
Check that the circuit breaker used for the air conditioner has not been  
triggered.  
Check that the power cable is plugged into a wall socket and the socket is  
switched on, if necessary.  
The air conditioner does  
not operate at all  
Check that the temperature indicator on the unit is lit; if necessary,  
press the  
(On/Off) button on the remote control or unit.  
Check that there are no obstacles between you and the unit.  
Replace the remote control batteries if necessary.  
Check that you are close enough to the unit (seven metres/yards or less).  
The air conditioner does not  
operate with the remote  
control  
Check that you are pointing the remote control at the remote control sensor  
on the unit.  
No beep is heard when you  
press the  
(On/Off) button  
on the remote control  
Replace the remote control batteries if necessary.  
Check that the correct operating mode has been selected(Cool).  
The room temperature may be too low.  
The air conditioner does not  
cool  
Dust may be blocking the air filter; refer to page 17 for cleaning instructions.  
Check that there is no obstacle blocking the air flow into or out of the unit.  
Check that the timer has been programmed correctly; refer to page 12~14.  
The timer is not correctly trig-  
gered  
Odors are permeating the  
room during air conditioning  
Ventilate the room.  
E-18  
Technical Specifications  
Design and specifications are subject to change without notice.  
Model  
Power Supply  
AW0605B  
AW0695B  
AW0805B  
AW0895B  
AW089DB  
AW1005B  
AW1095B  
AW1205B  
AW1295B  
AW109BB  
AW129BB  
AW109DB  
AW129DB  
115V~, 60Hz  
E-19  
YOUR SAMSUNG ROOM AIR CONDITIONER  
WARRANTY  
Limited Warranty to Original Purchaser  
Samsung will repair or replace, at our option, this product if found defective within the warranty  
period beginning from the original date of purchase. This Samsung Product is warranted by  
SAMSUNG ELECTRONICS CANADA Inc. against manufacturing defects in materials or  
workmanship for the period specified.  
Labor  
Parts  
1 Year (In home)  
1 Year  
Limited 5-Years Compressor Warranty  
Within one year of purchase Samsung Electronics Canada Inc. will provide a replacement  
compressor if it is found to be defective in material or workmanship. During the existing four  
years (second through fifth year) Samsung Electronics Canada Inc. will provide a replacement  
only, without charge, if it is found to be defective in material or workmanship. Labor to install  
the compressor during these existing four years is not included in the warranty. All warranty  
repairs must be performed by a Samsung Authorized Service Centre.  
Obligation of the Original Owner  
The original dated purchase receipt must be retained as proof of purchase and presented to  
the Authorized Service Centre before warranty services are rendered.  
Exclusions of the Warranty  
This warranty does not cover damage due to accident, fire, flood and/or other Acts of God:  
misuse, incorrect line voltage, improper installation, improper or unauthorized repairs,  
commercial use, or damages which occur in shipping. Exterior and interior finish and plastic  
parts, are not covered under this warranty, Customer adjustments which are explained in the  
instruction manual are not covered under the terms of this warranty. This warranty will  
automatically be voided for any unit found with a missing or altered serial number.  
This warranty is valid only on products purchased and used in Canada.  
SAMSUNG ELECTRONICS CANADA INC.  
55 Standish Court, Mississauga, Ontario L5R 4B2  
Printed in Korea  

Lexmark Intuition S505 User Manual
Motorola Battery Charger Wpln4117 User Manual
Panasonic Cu E24ekr User Manual
Panasonic Cw Xc244hu User Manual
Philips Lr03pb12a User Manual
Sanyo Ch3682 User Manual
Sonicwall Answering Machine 8000 User Manual
Toshiba Answering Machine Sm Qrc Vb User Manual
Toshiba Rav Sm1402ct E User Manual
York 14 User Manual