Q See Qsdb8209c User Manual

QSDB8209C  
Digital LCD Baby Monitor  
and Wireless Camera  
Visit Us on the Web at http://www.q-see.com  
Rev 072208  
2. Diagram  
3. Structure  
3-1. Layout of Camera  
3-2. Layout of Receiver  
4. Installation  
4-1. Setting Up the Camera  
1. Setup the camera in the desired location  
2. Connect the camera to the adapter and then slide the power switch to the ON  
position  
Note:  
--This camera can also use dry batteries as a power source by loading 4 AA  
batteries into the battery compartment on the back of the camera with their  
polarities in the correct position.  
--The AC adapter will work instead of batteries after it is plugged in. If the  
camera is not going to be used for a long period of time, please unplug the  
adapter and remove the batteries.  
* The camera can run off of batteries for up to 5 hours (IR OFF)  
3. Rotate the rounded head of the camera to the desired angle for surveillance.  
4-1-1. Camera Learning Setup  
If there is interference from another wireless device the Learning Switch can  
program the unit to avoid it. Push the Learning Switch on the back of the camera  
from OFF to ON, then press the Eliminate button on the receiver for 3 seconds.  
The picture will become clearer on the screen.  
4-1-2. Camera Alarm Setup  
1. The camera provides a Sound Detection alarm.  
Sound Alarm Setup:  
To set up the sound alarm slide the alarm switch to the VOX position. The  
system will enter standby mode until a sound triggers the alarm. When sound is  
detected the alarm sounds for two minutes or until the Eliminate Alarm button is  
pressed, which will put the system into snooze mode for 35 seconds. After the  
35 seconds is up the alarm will go back into standby mode until triggered by the  
next sound alarm event.  
Turn Off Alarm:  
To turn off the alarm slide the alarm setting switch to the Off position. The alarm  
function will be disabled.  
Note:  
The Sound alarm will be turned off automatically if the Eliminate Alarm button  
is not pressed within 2 minutes after the alarm sounds. If both the battery and  
A/C adapter are in use and the alarm setup failed to trigger, turn the camera and  
the receiver off and then back on to re-activate the alarm.  
4-2. Setting Up the Receiver  
1. Connect the receiver to the adapter and then slide the power switch to the ON  
position.  
Note:  
--This receiver can also use dry batteries as a power source by loading 4 AA  
batteries into the battery compartment at the back of the camera with their  
polarities in the correct position.  
--The AC adapter will work instead of batteries after it is plugged in. If the  
camera is not going to be used for a long period of time, please unplug the  
adapter and remove the batteries.  
* The camera can run off of batteries for up to 5 hours.  
2. Adjust the volume control to the desired level.  
3. Set the channel of the receiver to the same channel as the camera by pressing  
the channel button continuously, the pictures will display on the screen when the  
channels match.  
Note:  
The receiver supports up to 4 cameras working at the same time. If there are 2, 3,  
or 4 cameras working you can press and hold the channel button about 3 seconds  
to enter auto-switch-browse mode and the channels will by displayed one by one  
for 6 seconds at a time.  
5. Specifications  
Item  
Value  
Transmission Frequency  
ISM 2,400~2,483 MHz  
Transmission Power  
Operating Frequency  
10mW/CE; 2mW/FCC  
2414MHz;2432MHz;2450MHz;2468MHz  
Unobstructed Effective  
Range  
Spread  
100m (328ft)(Min.)  
FHSS/GFSK  
GENERAL  
Spectrum/Modulation Mode  
Operating Temperature  
Operating Humidity  
Imaging Sensor Type  
-10 ~ +50(Degree C) / +14~ +122(Degree F)  
≤85%RH  
CMOS  
PAL:720×480 Pixels;  
NTSC: 720×576 Pixels  
Picture Total Pixels  
Horizontal Resolution  
View Angle  
380 TV Lines  
55°  
Minimum Illumination  
Image Resolution  
Night Vision Range  
Battery Working Time  
0Lux (IR ON)  
320x240 @ 10fps  
5m  
CAMERA  
5 hours (IR OFF)  
Motion Detection Distance 5m (16ft)  
Sound Control Sensitivity >65dB  
Consumption Current  
Power Supply  
280mA (Max.)  
DC +8V  
Dimensions(W×D×H)  
Weight  
86*48*135 mm (3.5*2*5.5 in)  
146 g (5.2 oz)  
2.36 inches TFT-LCD  
480×234  
LCD Screen Type  
Effective Pixels  
Receiving Sensitivity  
Battery Working Time  
Consumption Current  
Power Supply  
≤-85dBm  
5 hours  
MONITOR  
200mA (Max.)  
DC +8V  
Dimensions(W×D×H)  
Weight  
86*54*143 mm (3.5*2.25*5.75 in)  
130 g (4.6 oz)  
* Actual transmission range may vary according to weather, Location,  
interference and building construction.  
* All the specifications are subject to minor change without prior notice.  
6. FCC information  
This device complies with part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received, including interference  
that may cause undesired operation.  
Changes or modifications not expressly approved by the party responsible  
for compliance could void the user’s authority to operate the equipment.  
CAUTIONS:  
Do not expose the device to water or other liquids.  
Turn off the Camera/Receiver when the system is not in use.  
Make sure the power adapter is easily accessible.  
Only remove the Camera/Receiver from the main power line by  
unplugging the adapter.  
Do not cut the DC power cable of the device to fit with another power  
source.  
Make sure batteries are disposed of properly.  
EU Environmental Protection  
Electrical waste products (discharged batteries) should not  
be disposed of with household waste.  
Please recycle where facilities exist.  
Check with your Local Authority or  
retailer for recycling advice.  
TRADEMARKS  
All brand names and products are registered trademarks of their respective  
Companies.  
DISCLAIMER  
The information in this document is subject to change without notice. The  
manufacturer makes no representations or warranties with respect to the contents  
hereof and specifically disclaim any implied warranties of selling or  
functionality for any particular purpose.  
LEGAL DISCLAIMER  
Warning: Your security camera is a quality digital product.  
You have to take utmost care while handling this product  
in order to ensure its reliability & durability.  
Digital Peripheral Solutions Inc.  
8015 E Crystal Drive.  
Anaheim, CA 92807  
1-877-998-3440.  
Q-See Tech Support in U.S.A.  
Mon-Fri: 9 am 5 pm PST.  
TEL:1-877-998-3440 x 539  

Panasonic Kx Tg1034 User Manual
Philips Sc484 User Manual
Samsung Aw0660a User Manual
Sanyo N 1200sck User Manual
Schumacher Sc 2500a User Manual
Sharp Af S120dx User Manual
Sunbeam Sca103rwb1 User Manual
Toshiba 2051c User Manual
Whirlpool Acc602 User Manual
Xerox Workcentre 5645 User Manual