Oricom 200 User Manual

Baby Monitor  
Secure 200  
User Guide  
WARNINGS AND SAFETY INFORMATION 1  
Do not place the cord in a high "wear and tear" location.  
Never use a frayed or compromised cord.  
IMPORTANT  
Please read this user guide thoroughly before use.  
Never use or place your Parent or Baby units in or near  
moisture or water (e.g. near bath or pool). Immersing in  
water can cause electric shock and even death.  
Your ORICOM Baby Monitor is designed to be an aid and  
should not be used as a substitute for responsible and  
proper adult supervision of a child.  
The Baby Monitor has been designed to provide some  
added reassurance in the form of sound transmission  
for those times when you are not in the same room as  
your baby provided you always stay within hearing range  
of the baby monitor during use. Your Baby Monitor is  
not a medical device, nor a device to prevent cases of  
Sudden Infant Death Syndrome (SID'S) or "cot death",  
and you should not rely on it for your baby's wellbeing. It is  
important that you regularly check on your baby personally.  
Power requirements  
In Australia this product requires an electrical supply of  
220-240 volts, single phase/alternating current.  
CAUTION  
Use only the mains power adaptors supplied with this  
equipment. Incorrect adaptor polarity or voltage can  
seriously damage the unit and/or cause physical harm  
and even death. The adaptors may become warm during  
use, please take care when handling.  
!
Make sure the Baby unit, Parent unit and mains adaptor  
cables are kept out of reach of your baby and other young  
children within the house at all times, at least one metre  
away from the baby’s cot.  
AC Adaptor (Baby unit)  
Input: 240VAC 50Hz  
Output: 6VDC 200mA  
AC Adaptor (Parent unit)  
Input: 240VAC 50Hz  
Output: 6VDC 200mA  
Never place the baby unit inside your baby’s cot, bed or  
playpen.  
If you plan to use your Baby monitor whilst travelling  
overseas, make sure that the voltage shown on the mains  
power adaptor is the same as the local mains power before  
connecting to the power supply. Do not use any voltage  
converter with the monitor.  
Never cover the Parent or baby units with clothes, towels  
or blankets or any other item.  
2 WARNINGS AND SAFETY INFORMATION  
• The Ni-MH batteries supplied with this product may be  
Battery requirements  
able to be recycled once they are unable to recharge  
during normal operation. Always observe your local  
Council /State regulations regarding the disposal of  
your packaging materials, exhausted batteries, and old  
equipment.  
Each parent unit requires two rechargeable Ni-MH  
batteries, size AAA 1.2V 800mAh (HR10/44).  
• Do not dispose of the batteries in a re, as they can  
explode.  
• Always recycle where possible. Do not use your baby  
monitor in an explosive hazard area such as where  
there is gas leaking.  
• Do not open, unscrew or temper with any of your  
baby monitor units or battery. Always carry out repairs  
through your authorised ORICOM representative or  
other duly qualied tradesperson.  
• As there is a slight chance that the product could be  
damaged by an electrical storm, it is recommended that  
users unplug from the mains supply during an electrical  
storm.  
• Released electrolyte from the battery is corrosive  
and can cause damage to the eyes or skin. It can  
be toxic and fatal if swallowed. If there is any sign of  
poisoning, immediately call emergency 000.  
Cleaning and care  
• When your Baby Monitor is not in use, it is recom-  
mended that you disconnect it from the mains supply  
and remove the batteries.  
The surface of the case can be cleaned with a dry, soft,  
lint-free cloth. Never use cleaning agents, particularly  
aggressive solvents. Apart from occasional cleaning of the  
case, no other care is necessary.  
• Observe the proper polarity, or direction, of any  
battery. Reverse insertion of the battery cell can  
result in leakage or explosion and in turn harm or  
even death.  
GETTING STARTED 3  
Thank you for choosing this monitor from Oricom.  
Installation  
Your Secure 200 Baby Monitor offers the best Digital  
Technology.  
For the Parent Unit  
clip  
1. Remove the Belt Clip by  
lifting the clip at the top and  
sliding it downwards.  
INTERFERENCE  
FREE FREQUENCY  
2. Then remove the battery  
cover on the back of the  
Parent Unit by pressing  
and sliding it down. Insert  
the rechargeable batteries  
(supplied) as marked on  
the unit and close the cover  
again.  
DECT (Digital Enhanced Cordless Telecommunications) is the  
most widely used worldwide digital cordless technology, offering  
amazingly clear sound, long range and maximum voice security.  
DECT operates on the 1.8Ghz frequency which eliminates potential  
interference from other common wireless devices such as cordless  
telephones, wireless networks (Wi-Fi), Bluetooth and cordless  
computer devices.  
battery cover  
3. Place the Parent Unit into the Charger Pod.  
4. Plug the mains adaptor into a mains power socket.  
Pack Contents  
The red charger light on the charger pod will illuminate  
indicating that the Parent Unit is charging.  
(the light will remain on to ensure optimum charge is  
maintained).  
Parent unit (receiver)  
Baby unit (sender)  
Mains adaptor with charger pod  
2 x NiMH rechargeable batteries (type AAA, 800mAh)  
Mains adaptor with power cord  
WARNING  
DO NOT USE STANDARD/ALKALINE BATTERIES  
IN THE PARENT UNIT, AS THERE IS A RISK OF  
EXPLOSION AND/OR INJURY. USE ONLY Ni-MH  
RECHARGEABLE BATTERIES AS SUPPLIED.  
!
4 GETTING STARTED  
5. Press [  
] to turn the Parent Unit on.  
4. Press and hold [  
] key to turn on the baby unit.  
• Before rst use, or if it has been out of use for a long  
time, the Parent Unit will need to be charged for 15-16  
hours. During this time, the Parent Unit will operate  
from the Charger pod when switched on. Note that the  
Parent Unit cannot be used without batteries, even if it  
is placed in the charger pod.  
• The Baby Unit should be placed about 1 metre  
to 1.5 metres away from the baby's cot on a flat  
surface. Never place the Baby Unit inside the cot,  
bed or playpen. Make sure the unit, cords and mains  
adaptor are out of reach of the baby and other  
young children. Never place either Unit on antique  
or polished surfaces (as slippage or scuffing may  
occur). The unit may cause harm if it falls onto baby  
or other young children.  
For the Baby Unit  
1. In event of a power failure, your Baby Monitor can  
switch to battery power. It is therefore recommended  
that you insert non-rechargeable batteries in the  
Baby Unit.  
2. Remove the battery cover on  
the back of the Baby Unit by  
pressing and sliding it down.  
Note:  
If you place the Parent and Baby units too close together  
you will hear a high pitched noise called "feedback", this is  
normal. The units are designed to be located in separate  
rooms.  
To prevent feedback, do not take the Parent unit into the  
nursery/baby's room.  
Insert 3 alkaline batteries of the  
Push  
type AA (not provided) as marked  
Do not Press Talk button when the Baby unit and Parent  
unit are positioned in the same room. Feedback will be  
generated if the talk button is pressed when the Baby unit  
and Parent unit are within 3 metres of each other.  
on the unit and close the cover  
again. Do not use rechargeable  
batteries in the Baby Unit.  
3. Plug the power cord into the power input at the side of  
the Baby Unit and plug the adaptor plug into a mains  
power socket.  
YOUR BABY MONITOR 5  
Baby unit (Sender)  
9 Microphone  
1 Temperature Sensor  
Picks up the sounds from your baby's room.  
10 Volume Up/Down Keys  
Picks up the temperature in your baby's room.  
2 Battery Cover  
Volume : Reduces the lullaby volume.  
Volume +: Increases the lullaby volume.  
For non rechargeable batteries (not supplied).  
3 Night light key  
Press to turn On the night light. Press again to turn Off  
the light.  
4 Power On/Off Key  
Press to turn ON the Baby unit.  
Press and hold to turn OFF.  
5 Page key  
1
2
Press and hold for 2 seconds to Page the Parent Unit  
with an audible alert. Useful to call for assistance or to  
locate a missing Parent Unit.  
3
4
5
6 Display  
6
Indicates the current settings of your Baby Monitor,  
including: Battery level, Date and Time, Temperature,  
Lullaby on/off, Lullaby melody.  
7
8
7 Play/Stop key (Lullabies)  
Press to start or stop the lullaby music.  
8 Music key (Lullabies)  
10  
9
Press to select the lullaby melody.  
6 YOUR BABY MONITOR  
Left view of baby unit  
Parent unit (Receiver)  
11 DC 6V input  
12 Battery Cover  
Connecting to Power Adaptor.  
Rechargeable batteries.  
13 Belt Clip  
14 Volume Up/Down Keys  
Adjust the volume at which you hear the sounds in  
your Baby's room, and scroll through the menu during  
setting.  
15 Power On/Off Key  
Press to turn the parent unit ON. Press and hold to turn  
OFF.  
11  
13  
14  
15  
12  
YOUR BABY MONITOR 7  
16 Menu key, [OK] key  
19 Noise level indicators  
20 Torch key  
Press to adjust the features of your Baby Monitor.  
Press [ ] key to enter the menu options, use [  
keys to scroll through the menu choices and [OK] key to  
select. Press [ ] key to exit.  
/
]
Press and hold to emit a soft beam of light from the top  
of the Parent Unit.  
21 Talk key  
17 Link Light  
Press and hold to talk to your baby or partner in the  
baby's room via the Baby Unit.  
Green light ON indicates "Linked" to Baby Unit. Flashing  
light indicates "Link" is lost.  
Charger Pod  
18 Display  
Indicates the current settings of your Baby Monitor,  
including: Battery level, Date and Time, Temperature,  
Lullaby on/off, Lullaby melody.  
22 Charging Light  
When Parent unit is placed in the Charger Pod, the  
red charger light comes ON to indicate the batteries  
are charging. Light will remain ON to ensure optimum  
charge is maintained.  
19  
20  
18  
17  
21  
16  
22  
8 LCD DISPLAY OF BABY MONITOR  
Baby Unit  
Parent Unit  
1. Battery level indicator  
1. Sensitivity indicator  
2. Numbers/Characters indicator  
3. Temperature indicator  
4. Lullaby on/off indicator  
2. Night light indicator  
3. Battery level indicator  
4. Numbers/Characters indicator  
5. Temperature indicator  
6. Feed time Alarm indicator  
7. Lullaby on/off indicator  
5
1
2
1
2
3
4
6
7
3
4
BASIC OPERATION 9  
Once you have set up your Baby Monitor, you will be able  
to hear the sounds in your baby's room through the Parent  
Unit. And also see the green and red sensor lights around  
the top of the Parent Unit rise and fall with the sound levels.  
and 3 red). The more audio is picked up, the more  
lights will be lit. When no audio is picked up, all 8  
lights will be off.  
• If the volume of the Parent Unit is turned off, an alert  
will sound when the audio reaches the second red  
led.  
Note:  
If the connection between the Parent and Baby Units is  
broken at any time the green Link light on the Parent Unit  
will ash slowly, the parent unit will beep to alter you that  
the link has been lost and the green and red sensor lights  
will cease to react to any sounds. Move closer to the baby  
unit or follow the directions in "Troubleshooting" chapter to  
re-establish the link.  
Note:  
Do not position the baby unit and the parent unit close to  
each other as feedback may be generated.  
Adjusting Volume  
You can adjust the volume at which you hear your baby.  
Power On/Off  
There are 5 volume levels on both units and an Off setting  
on the parent unit.  
Once connected to the power supply,  
• Press [  
] on each Unit to turn on the power.  
On the parent unit  
• To switch off, press and hold the [  
].  
Press [  
] to increase the volume and [  
] to decrease  
the volume.  
Monitoring  
On the baby unit  
• Position the baby unit accordingly. It should be  
placed 1 metre to 1.5 metres away from the baby's  
cot on a at surface.  
Press [  
] to increase the volume and [  
] to decrease  
the volume.  
When adjusting the volume, the volume level will be  
displayed on the both units LCD display.  
• Take the parent unit to monitor.  
• Audio picked up by the baby unit microphone is  
depicted on the 8 lights on the parent unit (5 green  
10 BASIC OPERATION  
Baby alert!  
Night light  
You can set your Parent Unit to give an extra warning The Baby Unit has a night light which emits a soft starry  
"beep" when the noise levels in your baby's room is glow, providing comfort and reassurance for your baby and  
high and the red lights on the sound sensor are lit. This allowing you to see them in a darkened room.  
is particularly useful if the volume of your Parent Unit is  
turned down and you are just using the sensor lights to  
monitor the noise levels in your baby's room.  
On the baby unit  
Press [  
] key on the top of the baby unit. A soft light will  
turn on gently. Press again and the light will fade away.  
Follow the "Sound Alert setting" on the menu setting section  
to set the Sound Alert on or off, and adjust the alert volume.  
On the parent unit  
Press [  
] key and use [  
/
] keys to select "Night Light",  
Paging  
then press [ OK ] key to turn on or off the night light.  
If the Parent Unit is misplaced, you can use [ ] button on  
the Baby Unit to locate the Parent Unit.  
Lullaby  
• Press and hold [ ] for 2 seconds on the Baby Unit.  
The Parent Unit will automatically reset to mid volume  
and the paging alert will sound.  
Your baby can be soothed to sleep by a gentle lullaby  
from the Baby Unit. There are 5 tunes to choose from.  
The lullaby feature can be turned on and off from both the  
Baby Unit and the Parent Unit and is indicated on both by  
a musical note icon. The icon and the lullaby title show  
on both Displays when the lullaby is playing. The lullabies  
will play for 15 minutes. We recommend that you use the  
lullaby setting at the lowest volume setting which comforts  
your baby.  
• To stop the Page alert, press any button on the  
Parent Unit, or press [ ] again on the Baby Unit.  
Note:  
If no button is pressed, the paging tone will stop after 2  
minutes.  
If the Parent Unit volume is off, the Parent Unit volume will  
reset to mid-volume.  
On the Baby Unit  
1. Press [ ] key. The lullaby is shown on the display.  
BASIC OPERATION 11  
2. Press [ ] key to scroll to the different lullabies, or to  
select [Play all?].  
Temperature  
It is very important for your baby's health to ensure that  
they are kept at a safe temperature. This includes the  
room temperature, baby's temperature, baby clothing and  
bedding (contact your local health authority to ensure you  
are aware of the current recommendations and guidelines).  
Your Baby Monitor can show the current room temperature  
on the Baby Unit and the Parent Unit, and can even be  
set to alert you if the temperature falls outside of a dened  
range.  
3. Press [  
] key again to start or stop the lullaby.  
On the Parent Unit  
1. Press [  
"Lullaby". Press [ OK ] key.  
2. "Play?" is shown on the display. Use [  
scroll to "Select New". Press [ OK ] key.  
] key, then use [  
/
] keys to scroll to  
] keys to  
/
3. The Display shows the current lullaby. Use [  
/
]
keys to scroll to your choice of tune, or to "Play All".  
Press [ OK ] key.  
4. "Lullaby" is shown on the display. Press [ OK ] key to  
play the lullaby.  
Follow the "Temperature setting" on the Menu Setting  
section to set the temperature range, temperature alert and  
change from Centigrade to Fahrenheit.  
5. To stop playing, press [ OK ] key and "Stop?" is shown  
on the display, and then press [ OK ] key again.  
Time for a Feed  
If your baby is in a routine of regular feeding intervals, you  
may wish to set your Baby Monitor to alert you when your  
baby's feeds are due. You have the choice to either set an  
alert just for your baby's next feed time, or for your baby's  
next feed time plus subsequent feeds based on the interval  
time between them.  
Clock  
You can set the Display of the Parent Unit to show the  
current day and time. It can be shown as either the 24 or  
12 hour clock (24 hour clock is the default). You will need  
to set the clock if you wish to use Feed Timer feature.  
Follow the "Feed Time Setting" on the Menu Setting section  
to set the rst or next feed time, the interval for following  
feeds and to turn the feed alarm on or off.  
If you have unplugged your Baby Monitor from the power  
supply, you will need to reset the Clock the next time you  
use it.  
Follow the "Clock Setting" on Menu Settings to set the time.  
12 BASIC OPERATION  
will be shown on both units LCD display. When the units are  
linked, the green Link light will be steadily lit.  
Talk to your Baby  
You can speak to your baby from the Parent Unit, perhaps  
to reassure them that you are on your way.  
Torch  
Press and hold [  
Parent Unit.  
] key and speak into the front of the  
The Parent Unit has a useful Torch feature. Press and hold  
the button on the parent unit, a soft beam of light is emitted  
from the top of the Parent Unit. It is helpful when peeping  
into a darkened room to check on your baby.  
• Please note that you will not be able to hear your  
baby while you are speaking to them until you release  
[
] key again.  
Low Battery  
Customize your Baby Monitor to your Baby  
Baby Unit  
Some babies are louder than others! You can customize  
the sound sensitivity of your Baby Monitor to suit your  
baby. Set the sensitivity "High" for a quiet sleeper with a  
soft cry and set to "Low" sensitivity if they tend to make  
noise when sleeping or can make quite loud noises before  
they are truly crying.  
When the battery power is low, the battery icon on the  
display will ash.  
Parent Unit  
When the batteries are low, the battery icon on the display  
will ash. And also the low battery alert tone will sound. The  
unit still can be used for 30 minutes. You should put the  
parent unit on the charger pod to recharge the batteries.  
Follow the "Sensitivity Setting" on Menu Settings to set the  
sensitivity.  
Note:  
Out of Range  
Low battery alert can be suppressed by pressing any  
button.  
When the baby and parent units have no link with each other  
(eg. Out of range, parent unit or Baby unit is not powered  
on), the green Link light ashes. The link break alert will be  
heard from the Parent Unit every 30 seconds, and "no link"  
BASIC OPERATION 13  
Rechargeable batteries in the Parent unit give up to 10  
hours continuous usage. Please note however, that new  
batteries do not reach full capacity until they have been in  
normal use for several days.  
Charging the Battery  
The Parent Unit will work for up to 10 hours with fully  
charged batteries. If a battery low alert tone is heard and  
the battery icon on the Parent Unit's display is ashing, you  
should put the parent unit on the Charger Pod to recharge  
the batteries. You can still use your Parent Unit from the  
Charger Pod. When charging, the red power light on the  
charger will light steadily.  
Running rechargeable batteries right down at least once a  
week will help them last as long as possible. The charge  
capacity of recharge batteries will reduce with time as they  
age, so reducing the performance time of the parent unit.  
Eventually they will need to be replaced.  
When you switch on your Parent Unit, the battery icon  
on the display will indicate the current charge level of the  
batteries.  
Note:  
The parent unit can be used on or off the charger pod.  
When on the charger pod, the batteries will be recharged  
at the same time. However, the time it takes to charge the  
batteries to full will be longer when the unit is charged and  
used at the same time.  
The Parent Unit can't be operated on the charging cradle  
without batteries.  
14 MENU SETTINGS  
Note:  
All Menu settings operations are only available on the  
Parent unit.  
During setting, press [  
] key to exit.  
Night light Setting  
Start playing  
Press [ OK ] key, "Play?" is shown, press [ OK ] key to play  
the lullaby and "Saved" is shown on the display.  
You can turn on or off the night light on the baby unit via  
the parent unit.  
1. Press [  
] key on the parent unit and use [  
/
] keys  
To stop lullaby, press [OK] again, "Stop?" is shown and  
Press [ OK ] to stop lullaby and "Saved" is shown on the  
display.  
to select "Night Light". The display is shown below:  
Selecting lullaby  
1. Press [ OK ] key and use [  
New".  
2. Press [ OK ] key and use [  
/
] keys to select "Select  
] keys to select lullaby  
2. Press [OK] key to select night light on or off and "Saved"  
is shown on the display.  
/
and "Play All". There are 5 lullabies.  
3. Press [ OK ] key and "Saved" is shown on the display.  
Lullaby Setting  
Sensitivity Setting  
You can play lullabies on the baby unit via the parent unit.  
You can adjust the sensitivity on the Parent Unit to monitor  
the sound from the Baby Unit. For example, if your baby is  
a particularly quiet sleeper, you can increase the sensitivity  
levels so that you are sure to hear if your baby is disturbed  
or becomes uncomfortable.  
Press [  
] key on the parent unit and use [  
/
] keys to  
select "Lullaby". The display is shown below:  
MENU SETTINGS 15  
1. Press [  
] key on the parent unit and use [  
/
] keys  
Set On or Off  
to select "Sensitivity". The display is shown below:  
1. Press [ OK ] key, "On?" or "Off?" is shown on the  
display, press [ OK ] key to select Sound Alert on or off  
and "Saved" will be displayed on the parent unit.  
Adjust Volume  
2. In the Sound Alert setting menu, use [  
select "Volume" and press [ OK ] key.  
/
] keys to  
2. Press [ OK ] key and then use [  
/
] keys to select the  
3. Use [  
/
] keys to select the volume level. There are 5  
sensitivity level. There are 5 levels.  
3. Press [ OK ] key to confirm and "Saved" is shown on  
the display.  
volume levels.  
4. Press [ OK ] key to conrm and "Saved" will be shown  
on the display.  
Sound Alert Setting  
Temperature Setting  
You can set the sound alert of the parent unit on or off, and  
also the volume of the sound alert.  
You can monitor the temperature in the baby's room on  
both the parent and baby unit.  
Press [  
] key on the parent unit and use [  
/
] keys to  
You can select the baby room temperature alert range. The  
lower limit can be set from 18°C to 25°C and the upper limit  
from 19°C to 26°C. If selected an alert on the parent unit  
will sound and the display will ash if the room temperature  
falls outside the selected range.  
select "Sound Alert". The display is shown below:  
Please note the baby monitor cannot manipulate the  
temperature in your baby’s room, it only provides a  
temperature reading.  
16 MENU SETTINGS  
Press [  
] key on the parent unit and use [  
/
] keys to  
Set degree Centigrade or Fahrenheit  
select "Temperature". The display is shown below:  
You can choose whether to view the temperature of your  
baby's room in degrees Centigrade or degrees Fahrenheit.  
Your monitor is pre-set to Centigrade, but if you wish to  
change it, follow the steps below:  
1. In the Temperature setting menu, use [  
select "Degree F" or "Degree C".  
/
] keys to  
2. Press [ OK ] key to conrm and "Saved" will be shown  
Set desired baby room temperature range  
1. Press [ OK ] key, "Set Range" is shown on the display.  
on the display.  
2. Press [ OK ] key, use [  
lower temperature limits.  
3. Press [ OK ] key to confirm and "Saved" is shown on  
the display.  
/
] keys to set the upper and Clock Setting  
You can set the current day and time on the Display of the  
Parent Unit.  
If you have unplugged your Baby Monitor from the power  
supply, you will need to reset the Clock the next time you  
use it.  
Set temperature alert  
You can turn on and off the temperature alert on the Parent  
Unit.  
[
]
1. Press  
key on the parent unit and use [  
/
] keys  
to select "Clock", the display is shown below:  
1. Use [  
/
] keys to select "Temp Alert", and press [ OK ]  
key to set the temperature alert on or off.  
Set temperature alert volume  
2. Or use [  
volume levels.  
3. Press [ OK ] key, and use [  
/
] keys to select "Volume". There are 5  
/
] keys to adjust volume  
level, press [OK] key to conrm and "Saved" is shown  
on the display.  
MENU SETTINGS 17  
baby's feeds are due. You have the choice to either set an  
alert just for your baby's next feed time, or for your baby's  
next feed time plus subsequent feeds based on the interval  
time between them.  
Set the time  
2. Press [ OK ] key and "Set time" is shown on the display.  
Press [ OK ] key.  
3. "Year" is shown on the display. Use [  
select the correct year. Press [ OK ] key.  
4. "Month" is shown on the display. Use [  
select the correct month. Press [ OK ] key.  
5. "Day" is shown on the display. Use [  
select the correct day. Press [ OK ] key.  
/
] keys to  
] keys to  
] keys to  
] keys to  
Firstly you will need to ensure that you have set the date  
and time on your Parent Unit's inbuilt clock.  
/
Once you have done this, you can either:  
/
1. Set the Time of day or night (24hr clock) at which your  
baby's next feed is due (eg. 10.30) and then if you wish,  
2. Set the Interval between your baby's following feed start  
times, (eg. every 3hrs 30mins), be sure to include the  
time it takes to feed your baby.  
3. Finally, you will need to switch the Feed Alarm on. Now,  
when your baby's next feed is due, your Parent Unit will  
start beeping and the Display will show "Feed Alarm".  
Pressing any button on the Parent Unit will silence the  
alert and you can feed your baby. If you have set the  
interval, the alert will sound again when the next feed is  
due.  
6. "Hour" is shown on the display. Use [  
/
select the correct hour using the 24 hour clock. Press  
[ OK ] key.  
7. "Minute" is shown on the display. Use [  
/
] keys to  
select the correct minute. Press [OK] key and "Saved"  
is shown on the display.  
Set the hour format  
Use [  
/
] keys to select "Hour Format", press [ OK ] key,  
"12Hrs?" or "24Hrs?" is shown on the display, press [ OK ]  
key to select 12 hours or 24 hours clock format.  
Press [  
] key on the parent unit and use [  
/
] keys to  
select "Feed Time", the display is shown below:  
Time displayed in the 12 hour clock format will include a  
small "a" to denote AM and a small "p" for PM.  
Feed Time Setting  
If your baby is in a routine of regular feeding intervals, you  
may wish to set your Baby Monitor to alert you when your  
18 MENU SETTINGS  
Set the rst or next feed time  
1. Press [OK] key, "Set Time" is shown on the display.  
2. Press [ OK ] key, then follow the procedures in the Set  
the time of Clock Setting to set the hour and minute.  
Language Setting  
The displayed information can be set in different  
languages.  
1. Press [  
] key and use [  
/
] keys to scroll to  
Set the interval for following feeds  
"Language". The display is shown below:  
1. Press [ OK ] key and use [  
Interval".  
/
] keys to select "Set  
2. Press [ OK ] key, follow the procedures in the "set the  
time" of Clock Setting to set the hour and minute.  
Set Alarm on or off  
1. Press [ OK ] key and use [  
2. Press [ OK ] key, "On?" or "Off?" is shown on the  
display, press [ OK ] key to set the Alarm on or off.  
2. Press [ OK ] key and use [  
language.  
3. Press [ OK ] key and "Saved" is shown on the display.  
/
] keys to select desired  
/
] keys to select "Alarm".  
Set Alarm Volume  
1. Press [ OK ] key and use [  
/
] keys to select "Alarm".  
2. Press [ OK ] key and use [  
"Volume".  
/
] keys to select  
3. Press [ OK ] key and use [  
/
] keys to select the  
alarm volume, there 5 volume levels.  
4. Press [ OK ] key to confirm and "Saved" is shown on  
the display.  
TROUBLESHOOTING 19  
Problem  
Possible cause(s)  
The red power lights do not turn on when you plug 1. Check if the units are properly connected to the power supply.  
in the power.  
2. Check if the power is turned on. If not, Press [  
] to turn on the power.  
1. You may have moved out of range. Move closer to the Baby Unit and wait 5  
seconds for the Link to establish.  
2. You may need to reestablish the Link between the two units. Turn both units  
off by pressing and holding the [ ] and then turn on again by pressing the [ ].  
The green Link light on the Parent Unit is ashing  
and cannot hear the sounds from your baby's  
room.  
Can't hear your baby on the Parent Unit but the  
Link light is still glowing steadily.  
Check if the volume is turned up on the Parent Unit.  
The battery icon on the Display is ashing on the Your re-chargeable batteries are running low. Return the Parent Unit to the  
Parent Unit.  
Charger Pod to recharge them.  
1. The batteries in the parent unit are not fully charged. Charge the parent unit for  
14 hours before use.  
2. The power to the baby unit may be turned off or disconnected, and or the Baby  
unit may be turned off. Reconnect the AC power adaptor to the baby unit and  
or turn on the baby unit.  
3. You may have to re-establish the link between the two units. You will need to  
remove the batteries from the parent unit and register the parent unit back to  
the baby unit by following the instructions below:  
Two horizontal bars ash centre of the display on  
the parent unit and "Not Linked" is shown.  
A. Ensure batteries are removed from the Parent unit (and baby unit if tted) and the  
AC power plug is disconnected from the Baby unit). Press and hold the [ ] on  
the BABY unit then plug in the AC power plug, after 2 seconds, when the baby  
unit night-lights ash release the [ ] button;  
B. Press and hold the [  
2 seconds, the parent unit will sound an alert and the level indication red  
LED’s will ash, then release the [ ] button;  
] on the PARENT unit then insert the batteries, after  
C. After a few seconds, the PARENT unit will give a conrmation tone and the  
units will be re-linked and ready to use.  
NOTE: Steps A and B need to be performed within 50 secs.  
A high pitched ear piercing noise will be heard  
from the units (feedback).  
Check if the Parent and Baby Units are too close together. Move them further apart.  
20 PRODUCT SPECIFICATIONS  
Feature  
Specications  
Operating Frequency  
DECT 1.8 GHz  
Up to 300m under optimum conditions. The range is  
reduced in buildings (up to 50m) as a result of walls, doors  
etc.  
Range  
Input: 240 VAC 50Hz  
Power supply (Baby Unit)  
Output: 6 VDC, 200 mA,  
Non rechargeable batteries, baby unit  
(not included in the package contents)  
Type: AA, 1.5 V Alkaline  
Transmitting power  
Average: 10 mW Maximum: 250 mW  
Input: 240 VAC, 50Hz  
Output: 6 VDC, 300 mA  
Power supply (Parent Unit)  
Re-chargeable batteries (Parent Unit)  
(included in the package contents)  
Type: AAA, 1.2 V, 800 mAh NiMH  
Approx. 10 hours  
Operating time with charged battery  
GUARANTEE 21  
Warranty (Australia)  
(a) Warranty Oricom International Pty Ltd (Oricom) warrants that  
the product is free from defects in materials and workmanship  
for a period of 12 months effective from the date of purchase.  
This warranty in no way affects your statutory warranty under  
the Trade Practices Act 1974 or any other similar legislation. It  
is important that you read the Warranty Card as it contains full  
and additional details of the warranty, limitation of warranty  
and conditions for receiving the warranty services during  
the warranty period. The Warranty Card is located in the  
package.  
Oricom will not be liable for consequential losses including loss of  
profits arising from a cause of action in contract, tort or any other  
statutory or common law (except where a statute or any law prohibits  
this exclusion). The warranty does not extend to damage caused by  
misuse, negligence, excessive voltage or lightning. This warranty in  
no way affects your statutory rights. Full details of the warranty are  
contained in the enclosed warranty card.  
Customer Support  
(b) Exclusion and limitation of liability. Oricom will not be in  
breach of a warranty or condition expressly stated in this User  
Guide or the Warranty Card or implied by the Trade Practices  
Act and excludes any liability arising under any statutory or  
common law for damages or any other remedy if the damage  
occurs as a result of:  
If you feel this product is not working correctly please consult  
the user guide and ensure that you are using the product in  
accordance with the instructions.  
To order spare parts additional parent units, replacement parts  
and in case of any technical issues you may have with this  
product please consult our website for further information or send  
us an email for a prompt response to your enquiry.  
(i) Failure by you to follow the instructions in the User Guide  
for the installation and proper functioning of the product;  
In the unlikely event of a fault developing, please contact us  
for assistance. If the product is then found to be faulty you will  
be asked to return it directly to us with a copy of the purchase  
receipt.  
(ii) Negligence on your part or misuse by you of the product;  
(iii) Any un-controlled external cause to the product not  
functioning including but not limited to electricity failure,  
lighting, over voltage;  
(iv) Non adherence by you to the warnings in the User Guide  
and the User Guide generally; and  
(v) Modification to the product or services carried out to the  
product by anyone other than Oricom or on Oricom's  
behalf.  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
South Windsor, NSW 2756  
Customer Support  
Phone: 1300 889 785  
Fax: (02) 4574 8898  

Lincoln Automobile Parts 1162 User Manual
Motorola Ls1203 User Manual
Samsung Eh052cav User Manual
Schumacher ManualCargador De Batera ManualSe 2254 User Manual
Toshiba Mmk Ap0092h User Manual
Ultra Products Ult31790 User Manual
Xerox Workcentre 7120 User Manual
York Sunline 2000 60 User Manual
York Ycjf24 User Manual
York Yhjf18 User Manual