PERS-2400B
PERSONAL
EMERGENCY
REPORTING
SYSTEM
BY
BY
Installation,
and Operation Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
1. FRONT PANEL FEATURES
2. REMOVING BOTTOM COVER
TROUBLE INDICATOR
• NORMALLY OFF
EMERGENCY BUTTON
• PRESS AND HOLD TO TRIGGER
THE EMEREGNCY ZONE
• PRESS DURING RING FOR
SPEAKERPHONE MODE
• PRESS DURING SPEAKERPHONE
MODE TO DISCONNECT
• LIGHTS WHEN ANY TRANSMITTERS ARE MISSING
(SUPERVISORY)
• BLINKS SLOWLY WHEN ANY TRANSMITTERS
HAVE A LOW BATTERY
TO ACCESS THE INSIDE OF THE CONSOLE
PRESS THE TWO LOCKING TABS IN AND
REMOVE THE CONSOLE'S BOTTOM COVER
POWER INDICATOR
CLEAR BUTTON
• STOPS ALARM
• LIGHTS WHEN AC IS PRESENT
• BLINKS SLOWLY WHEN BATTERY IS CHARGING
• BLINKS QUICKLY WHEN AC IS ABSENT
(CONSOLE ON BATTERY POWER)
• OFF IN TEST AND SETUP MODES
• ADDS CANCEL TO AN ALARM
REPORT IN PROGRESS
• PRESS IMMEDIATELY AFTER
EMERGENCY TO PREVENT REPORT
• CLEARS INDICATORS
• STOPS TROUBLE BEEPER
• PRESS FOR 5
SECONDS TO ADD
A TRANSMITTER
REMOVE
COVER
PRESS
TABS
IN
HOME BUTTON
• PRESS TO RESET ACTIVITY TIMER
• PRESS FOR 5 SECONDS TO TURN ACTIVITY TIMER OFF
• IF ACTIVITY TIMER IS OFF, PRESS FOR
5 SECONDS TO TURN ACTIVITY TIMER ON
HOME INDICATOR
• LIGHTS WHEN ACTIVITY TIMER IS ON
• BLINKS SLOWLY WHEN LESS THAN 15 MINUTES
REMAIN ON THE ACTIVITY TIMER
• BLINKS QUICKLY WHEN THE ACTIVITY TIMER HAS EXPIRED
HOME BUTTON COVER
• ADHESIVE BACKED PLATE TO
HIDE THE HOME BUTTON IF THE
ACTIVITY TIMER IS NOT USED
SENDING INDICATOR
• NORMALLY OFF
• FLASHES WHEN CONSOLE IS PLACING A CALL
3. CONSOLE BOTTOM FEATURES
4. OPTIONAL VB-4B VOICE BOARD INSTALLATION
PRESS-FIT MICROPHONE INTO
ROUND MOUNTING HOLE
2
1
CONNECT BLACK
MICROPHONE WIRE
TO CENTER
12-VOLT 1.2 AMP/HOUR
BACKUP BATTERY
TERMINAL
16 VAC 1.25 AMP
PLUG-IN
TRANSFORMER
CONNECT RED
MICROPHONE WIRE
TO THIS TERMINAL
3
4
EXTERNAL SPEAKER,
RELAY OUTPUT, AND
DIALER POWER
OPTIONAL
VB-4B VOICE BOARD
TERMINALS
1 AMP 2AG
BATTERY FUSE
(HIDDEN)
SEAT
MICROPHONE
CAREFULLY ALIGN
PINS TO CONNECTORS
ON BOTH ENDS OF BOARD
BE SURE THAT THE
WHITE ARROWS ON
AUDIO BOARD POINT
TOWARD THE
LOCAL
PHONE
JACK
5
NOTE: POWER MUST
BE OFF AND BATTERY
SHOULD BE REMOVED
OR DISCONNECTED
BEFORE INSTALLING
THE AUDIO BOARD
BATTERY AREA
PRESS BOARD
COMPLETELY
INTO CONNECTORS
TELEPHONE
LINE JACK
POWER
SWITCH
TEST
BUTTON
NOTE: AFTER THE AUDIO BOARD
IS INSTALLED AND ENABLED, THE
CONSOLE WILL SPEAK INSTEAD
OF BEEP DURING PROGRAMMING
1
5. OPTIONAL RELAY OUTPUT CONNECTIONS
6. OPTIONAL REMOTE SPEAKER/MIC CONNECTIONS
VB-4B
VOICE
BOARD
FORM "A" DRY CONTACT RELAY
24 VOLTS AT 1 AMP MAXIMUM
5
NOISEMAKER OR
VISUAL INDICATOR
4 - RELAY NORMALLY OPEN
3 - RELAY COMMON
EXTERNAL
POWER SUPPLY
2
1
REMOVE
JUMPER
WIRE
CONSOLE
TERMINAL BLOCK
CONSOLE
TERMINAL BLOCK
VB-4B TERMINAL BLOCK
EXTERNAL MICROPHONE (+)
MICROPHONE COMMON (-)
CONSOLE MICROPHONE (+)
5 - DIALER POWER
4 - RELAY NORMALLY OPEN
3 - RELAY COMMON
CONNECT WIRES
TO TERMINALS
DIALER COMMON
EXTERNAL SPEAKER
2 -
1 - EXTERNAL SPEAKER
NOTE: REMOVE
JUMPER WHEN
USING AN
USE
SHIELDED
TWISTED PAIR
WIRE FOR
MICROPHONE
EXTERNAL SPKR
NOTE: NOT
TESTED BY UL
SPKR
SPKR
ROUTE CABLE UNDER
STRAIN-RELIEF CLAMP
MIC (-)
MIC (+)
LINEAR
MODEL RSM-1
RSM-1
TERMINALS
RSM-1 TERMINAL BLOCK
7. BACKUP BATTERY
8. INSTALL TRANSFORMER
TURN POWER
1
CONNECT RED LEAD TO
POSITIVE AND BLACK LEAD TO
2
SWITCH OFF
PLUG TRANSFORMER
INTO AN UN-SWITCHED
NEGATIVE BATTERY TERMINAL
1
117 VAC OUTLET
ON
OFF
BATTERY TYPE: 12-VOLT, 1.2 AMP/HOUR
FIT BATTERY
3
SECURE
TRANSFORMER
INTO CONSOLE
2
WITH SCREW
SLIDE DOWN
THEN BACK
2
9. APPLY POWER - SELECT DIALING METHOD
10. TRANSMITTER INSTALLATION OPTIONS
TURN POWER
SWITCH ON
FOR ALL TWO-BUTTON TRANSMITTERS
IT WILL
ACTIVATE
USING
EITHER
BUTTON
WHEN IT IS
INSTALLED
WITH THE
ON
LEFT BUTTON
WHEN IT IS
INSTALLED
WITH THE
IT WILL ONLY
ACTIVATE
USING BOTH
BUTTONS
RIGHT BUTTON
NOTE: THE DEFAULT DIALING METHOD IS TONE DIALING
IF REQUIRED, CHANGE THE DIALING METHOD
BY PRESSING AND HOLDING THE HOME & CLEAR
BUTTONS WHILE SWITCHING THE POWER ON
FOR DXS-31 STATIONARY TRANSMITTERS
WHEN IT IS INSTALLED
WITH THE JUMPER SET
FOR DELAY
WHEN IT IS INSTALLED
WITH THE JUMPER SET
FOR INSTANT
IT WILL
FUNCTION
AS EMERGENCY
IT WILL
FUNCTION
AS ACTIVITY
FOR MODEL DXS-32: CUT JUMPER (INSTANT TX) FOR USE
AS AN ACTIVITY TX. SEE DXS-32 INSTALLATION INSTRUCTIONS
• 7 BEEPS SOUND FOR PULSE DIALING
• 8 BEEPS SOUND FOR TONE DIALING
11. INSTALLING SINGLE TRANSMITTERS
12. INSTALLING MULTIPLE TRANSMITTERS
ADDS MULTIPLE TRANSMITTERS
ADDS ONE TRANSMITTER AT A TIME
1
1
PRESS TEST BUTTON
• 4 BEEPS SOUND
(TEST MODE)
PRESS CLEAR BUTTON
FOR 5 SECONDS
• 5 BEEPS SOUND
(TX ADD MODE)
2
PRESS TEST BUTTON AGAIN
• 5 BEEPS SOUND
(ADD TX MODE)
2
ACTIVATE TRANSMITTER
• 1 BEEP SOUNDS
(TX ADDED)
CONSOLE REVERTS
TO OPERATE MODE
NOTE: EACH TIME THE TEST BUTTON IS PRESSED IN THE ADD TX MODE,
THE CONSOLE WILL BE READY TO INSTALL A TRANSMITTER IN THE NEXT
AVAILABLE SENSOR ZONE LOCATION. IF THE VB-4B VOICE BOARD IS
INSTALLED, THE CONSOLE WILL ANNOUNCE THE SENSOR ZONE LOCATION
NUMBER.
ACTIVATE TRANSMITTER
• 1 BEEP SOUNDS
(TX ADDED)
3
NOTE: IF THE CONSOLE'S MEMORY
IS FULL, ONE LONG BEEP SOUNDS WHEN
TRYING TO ADD A TRANSMITTER
DXS-62A
NOTE: IF THE CONSOLE'S MEMORY
IS FULL, ONE LONG BEEP SOUNDS
WHEN TRYING TO ADD A TRANSMITTER
3
REPEAT STEPS 1 & 2 FOR ADDITIONAL
TRANSMITTERS (UP TO 16 TOTAL)
NOTE: PRESS CLEAR BEFORE TRANSMITTING TO RETURN
TO OPERATE MODE WITHOUT ENTERING A TRANSMITTER
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED
DXS-62A
REPEAT STEPS 2 & 3 FOR
ADDITIONAL TRANSMITTERS
(UP TO 16 TOTAL)
PRESS CLEAR TO RETURN TO OPERATE MODE
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED
4
5
THE CONSOLE WILL RETURN TO OPERATE MODE
AUTOMATICALLY AFTER 30 SECONDS
THE CONSOLE WILL RETURN TO OPERATE
MODE AUTOMATICALLY AFTER 3 MINUTES
NOTE: WRITE DOWN EACH TRANSMITTER'S TYPE AND ZONE NUMBER
WHEN THE TRANSMITTER IS ADDED. THE CENTRAL STATION WILL NEED
TO KNOW THE TYPE AND REPORTING ZONE FOR EACH TRANSMITTER.
NOTE: WRITE DOWN EACH TRANSMITTER'S TYPE AND ZONE NUMBER
WHEN THE TRANSMITTER IS ADDED. THE CENTRAL STATION WILL NEED
TO KNOW THE TYPE AND REPORTING ZONE FOR EACH TRANSMITTER
3
13. TESTING TRANSMITTERS
14. ERASING TRANSMITTERS
PRESS TEST BUTTON
• 4 BEEPS SOUND (TEST MODE)
1
CAUTION: ALL TRANSMITTERS
WILL BE ERASED!
2
ACTIVATE EACH OF THE
CONSOLE'S TRANSMITTERS,
ONE AT A TIME
PRESS AND HOLD TEST BUTTON FOR 5 SECONDS
• 6 BEEPS SOUND (ALL TRANSMITTERS WERE ERASED)
1
COUNT THE NUMBER OF BEEPS
THAT THE CONSOLE SOUNDS
WHEN THE TRANSMITTER
IS ACTIVATED
3
1-BEEP = TX OK
2-BEEPS = TX HAD ALARM
3-BEEPS = TX MISSED STATUS
4-BEEPS = TX HAS LOW BATTERY
NOTE: WITH THE MODEL VB-4B VOICE BOARD
INSTALLED, THE CONSOLE WILL ANNOUNCE
THE TRANSMITTER STATUS
2
PRESS CLEAR TO RETURN TO OPERATE MODE
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED
4
PRESS CLEAR TO RETURN TO OPERATE MODE
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED
THE CONSOLE WILL RETURN TO OPERATE MODE
AUTOMATICALLY AFTER 3 MINUTES
THE CONSOLE WILL RETURN TO OPERATE MODE
AUTOMATICALLY AFTER 3 MINUTES
15. LOCAL PROGRAMMING WITH RA-2400
16. TELEPHONE CONNECTIONS
LOCAL
TELEPHONE
JACK
PERFORM THE STEPS DETAILED IN THE
1
TELEPHONE
RA-2400/PERS-2400 REFERENCE GUIDE (P/N 217163)
TO SET UP THE RA-2400 PROGRAM
TO LOCALLY PROGRAM
THE CONSOLE, CONNECT
THE MODEM'S LINE JACK
TO THE CONSOLE'S LINE
JACK
2
3
LINE-TO-LINE
PRESS TEST BUTTON
MOMENTARILY
• 4 BEEPS SOUND
(TEST MODE)
CONSOLE WITH
REAR COVER
INSTALLED
NOTE: CONSOLE WILL EXIT TEST MODE
AUTOMATICALLY AFTER 3 MINUTES
OR BY PRESSING THE CLEAR BUTTON
WHEN RA-2400 CONNECTION
TIMER STARTS COUNTING DOWN,
PRESS THE EMERGENCY BUTTON
• 4 BEEPS SOUND
4
5
(RA-2400 ANSWER)
ROUTE CABLES UNDER
STRAIN-RELIEF TABS
CONNECT LOCAL
TELEPHONE TO
THIS JACK
PERFORM PROGRAMMING IN
THE RA-2400 SOFTWARE, THEN
DISCONNECT FROM THE CONSOLE
CONNECT TELEPHONE
LINE TO THIS JACK
4
17. SYSTEM OPERATION
18. ACTIVITY TIMER
ENABLING THE ACTIVITY TIMER
PRESS THE HOME BUTTON FOR
5 SECONDS TO TURN THE
ACTIVITY TIMER ON
CONSOLE
STANDING BY
1
POWER LIGHT IS ON
NOTE: THE ACTIVITY TIMER CAN
BE ENABLED FOR 8, 12, OR
24 HOURS, OR DISABLED BY
PROGRAMMING
OTHER LIGHTS ARE OFF
NOTE: TO TURN THE ACTIVITY TIMER OFF,
PRESS THE HOME BUTTON FOR FIVE SECONDS
2
3
ACTIVITY TIMER RUNNING
TIME RUNNING OUT
- IN CASE OF EMERGENCY -
THE HOME INDICATOR WILL BLINK &
A SHORT BEEP SOUNDS EVERY
10 SECONDS WHEN LESS THAN
15 MINUTES OF TIME REMAIN
THE HOME INDICATOR WILL LIGHT,
SHOWING THAT THE ACTIVITY
TIMER IS ENABLED
PRESS AND
- OR -
ACTIVATE
MOMENTIARLY
HOLD
EMERGENCY
TRANSMITTER
EMERGENCY
BUTTON
PRESS TRANSMITTER
BUTTON FOR AT LEAST
2 SECONDS
SIREN SOUNDS
UNTIL CLEAR BUTTON
IS PRESSED,
CONSOLE
IN ALARM
4
RESETING ACTIVITY TIMER
THE SUBSCRIBER NEEDS TO
PRESS THE HOME BUTTON OR
TRIGGER AN ACTIVITY
TRANSMITTER BEFORE THE
TIMER EXPIRES TO PREVENT
AN INACTIVITY REPORT
CENTRAL STATION
REPORT IS COMPLETE,
OR SIREN TIME EXPIRES
SENDING LIGHT
FLASHES DURING
COMMUNICATION
PRESS CLEAR TO
STOP SIREN
(ADDS CANCEL TO
ALARM REPORT IN
PROGRESS)
PRESSING THE HOME BUTTON
RESTARTS THE TIMER
19. AUDIO BOARD OPERATION
20. SPEAKERPHONE OPERATION
1
PROGRAM THE CONSOLE TO ENABLE SPEAKERPHONE MODE
1
NOTE: SPEAKERPHONE MODE CAN ONLY BE USED ON INCOMING CALLS
AND WILL NOT FUNCTION WHEN THE CONSOLE IS OPERATING FROM
BACKUP BATTERY POWER. ATTEMPTING TO ANSWER WHILE THE CONSOLE
IS ON BACKUP POWER WILL CAUSE AN EMERGENCY ALARM.
WHILE THE TELEPHONE IS RINGING, ACTIVATING AN
EMERGENCY TRANSMITTER OR PRESSING THE EMERGENCY
2
2
BUTTON WILL SEIZE THE TELEPHONE LINE
CENTRAL STATION OPERATOR:
3
THE AUDIO BOARD WILL BEGIN 2-WAY FULL DUPLEX MODE
FOR AUDIO COMMUNICATIONS
3
WARNING: THE CONSOLE WILL NOT BE ABLE
TO REPORT AN EMERGENCY WHILE THE
SPEAKERPHONE MODE IS ACTIVE
NOTE: TO REPORT AN EMERGENCY WHEN THE SPEAKERPHONE IS IN USE,
PRESS EITHER THE EMERGENCY BUTTON OR THE BUTTON ON AN
EMERGENCY TRANSMITTER TO END THE PHONE CALL AND THEN PRESS
ONE OF THESE BUTTONS AGAIN TO REPORT THE EMERGENCY.
THE AUDIO BOARD WILL END AUDIO COMMUNICATIONS
WHEN EITHER:
4
• THE EMERGENCY BUTTON IS PRESSED
• ANY EMERGENCY TRANSMITTER IS ACTIVATED
• THE AUTO-DISCONNECT TIMER RUNS OUT
PRESSING ANY KEY OTHER THAN "9" WILL EXTEND THE AUDIO TIME
90 MORE SECONDS
NOTE: TO USE THE AUDIO MODES, THE MODEL VB-4B AUDIO MODULE
MUST BE INSTALLED IN THE CONSOLE
NOTE: TO USE THE SPEAKERPHONE MODE, THE MODEL VB-4B AUDIO
MODULE MUST BE INSTALLED IN THE CONSOLE
5
21. SUPERVISORY CONDITIONS
22. WIRELESS INSTALLATION TIPS
TRANSMITTER LOW BATTERY TROUBLE
WHEN A TRANSMITTER SENDS A LOW BATTERY SIGNAL THE
CONSOLE'S TROUBLE INDICATOR WILL BLINK SLOWLY.
WALLBOARD AND
WOOD STUDS
CONSTRUCTION
MATERIALS WILL
TRANSMITTER SUPERVISORY TROUBLE
AFFECT RADIO RANGE
IF A TRANSMITTER PROGRAMMED AS SUPERVISED FAILS
TO REPORT STATUS IN A 24 HOUR PERIOD, THE CONSOLE'S
TROUBLE INDICATOR WILL LIGHT.
90% - 100%
OF FULL POWER
CONSOLE BACKUP BATTERY TROUBLE
WHEN TROUBLE EXISTS,
THE CONSOLE WILL BEEP EVERY
HOUR UNTIL CLEARED:
THE CONSOLE WILL TEST ITS BACKUP
BATTERY EVERY 8 HOURS. IF THE BATTERY
TESTS LOW, THE POWER INDICATOR WILL
BLINK SLOWLY WHILE THE CONSOLE
CHARGES THE BATTERY.
CONCRETE WITH STEEL
REINFORCEMENT OR
METAL LATH AND PLASTER
LIGHT CONCRETE
OR BRICK
2-BEEPS = CONSOLE LOW BATTERY
3-BEEPS = TRANSMITTER SUPERVISORY
4-BEEPS = TRANSMITTER LOW BATTERY
65% - 95%
OF FULL POWER
10% - 70%
OF FULL POWER
THE CONSOLE WILL REPORT
TROUBLE AND/OR 30-DAY STATUS
TO THE CENTRAL STATION IF
ENABLED IN THE COMMUNICATOR
PROGRAMMING
CENTRALLY LOCATE CONSOLE
NOTE: THE CONSOLE WILL ANNOUNCE
THE SUPERVISORY CONDITIONS WITH
THE OPTIONAL MODEL VB-4B VOICE
BOARD INSTALLED. THE VOICE CAN
BE DISABLED THROUGH
CONSOLE LOCATION WILL
AFFECT RADIO RANGE
RIGHT
PROGRAMMING
TRANSMITTERS AT THE
OTHER END OF THE HOUSE
MIGHT BE TOO FAR AWAY
CLEARING TROUBLE INDICATIONS
PRESS THE CLEAR BUTTON TO STOP TROUBLE
INDICATORS AND SOUNDERS
NOTE: THE TROUBLE CONDITION WILL LIKELY OCCUR AGAIN
UNTIL THE PROBLEM IS FIXED
WRONG!
LINEAR LIMITED WARRANTY
SPECIFICATIONS
This Linear product is warranted against defects in material and workmanship for twelve
(12) months.This warranty extends only to wholesale customers who buy direct from Linear
or through Linear’s normal distribution channels. Linear does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC
for consequential damages arising out of or in connection with use or performance
of this product or other indirect damages with respect to loss of property, revenue, or
profit, or cost of removal, installation, or reinstallation. All implied warranties, including
implied warranties for merchantability and implied warranties for fitness, are valid only until
the warranty expires. This Linear LLCWarranty is in lieu of all other warranties express
or implied.
CODING FORMATS
DX CODE 24-BIT A1D PPM 1,048,567 CODES
DXS CODE 24-BIT A1D PPM 1,048,567 CODES
POWER REQUIREMENTS
PRIMARY SUPPLY 16 VAC 1.25 AMP PLUG-IN TRANSFORMER
BACKUP SUPPLY 12 VOLT 1.2 AMP/HOUR BATTERY
NORMAL OPERATING CURRENT 80 mA
ALARM OPERATING CURRENT 120 mA
BACKUP OPERATION DURATION 32 HOURS MINIMUM
BATTERY LIFE EXPECTED 3 YEARS
BACKUP SUPPLY OPERATING CURRENT 32 mA
RF CHARACTERISTICS
All products returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other
important details.
RECEIVER TYPE DUAL-DIVERSITY SUPERHETERODYNE
RF SENSITIVITY -100 dBm TYPICAL
RADIO FREQUENCY 315 Mhz
MAXIMUM RANGE 400 FEET LINE-OF-SIGHT, OPEN RANGE
UL LISTED FOR 150’
IMPORTANT WIRELESS INFORMATION
Linear radio controls provide a reliable communications link and fill an important need in
portable wireless signaling. However, there are some limitations which must be observed.
COMMUNICATOR
COMMUNICATOR FORMATS 4 BY 2 (GENERAL OR POINT-TO-POINT),
ADEMCO CONTACT ID
•
For U.S. installations only: The radios are required to comply with FCC Rules and
Regulations as Part 15 devices. As such, they have limited transmitter power and
therefore limited range.
UL TESTED WITH SURGARD SGMLRG-DG
CENTRAL STATION RECEIVER
DIALING TONE OR PULSE
DIALING DELAY 0 OR 15 SECONDS
•
A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies, regardless of
code settings.
REMOTE ACCESS PASSWORD 6 DIGITS
NOTE:THE INSTALLER MUST
ACCOUNT NUMBER LENGTH 4 DIGITS
PRIMARY TELEPHONE NUMBER 20 DIGITS
SECONDARY TELEPHONE NUMBER 20 DIGITS
SUPERVISORY TELEPHONE NUMBER 20 DIGITS
VERIFY COMPATIBILITY
BETWEEN THE PERS-2400B AND
THE UL LISTED DIGITAL ALARM
COMMUNICATOR RECEIVER
•
•
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
CONSOLE STATUS REPORT OPTIONAL 1, 7 OR 30 DAY REPORT
•
A general knowledge of radio and its vagaries should be gained prior to acting as a
wholesale distributor or dealer, and these facts should be communicated to the ultimate
users.
CONSOLE
OPERATING TEMPERATURE 32°-100° F (0-50° C)
EMERGENCY ALARM DURATION 1-30 MINUTES
ACTIVITY TIMER PERIOD 8, 12, OR 24 HOURS
AUDIO LISTEN-ONLY, 2-WAY MANUAL, 2-WAY DUPLEX,
SPEAKERPHONE
RELAY OUTPUT N.O. @ 24 VOLT AC/DC 1 AMP
MAXIMUM, NEC CLASS II CIRCUITRY
Copyright © 2008 Linear LLC
228279 B
|