Zebra Skimmers Corp.
MIX05120
®
Zebra Economy Mixer Manual
Package Contains:
1. Drum proportioner
4. Metering tip kit (14 tips)
5. Product information sheet
2. Suction tube (4 ft.) with foot valve
3. Discharge tube (4 ft.) max length
for delivery
THANK YOU FOR YOUR SUPPORT OF OUR PRODUCTS
Please use this equipment carefully and observe all warnings and cautions.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - NOTE- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
WEAR
protective clothing and eyewear when dispensing chemicals or other materials.
ALWAYS
ALWAYS
ALWAYS
CLEAN
WEAR
observe safety and handling instructions of the chemical manufacturers.
direct discharge away from you or other persons or into approved containers.
dispense cleaners and chemicals in accordance with manufacturer’s instructions. Exercise CAUTION when maintaining your equipment.
equipment after each use in accordance with instruction sheet.
protective clothing and eyewear when working in the vicinity of all chemicals, filling or emptying equipment or changing metering tips.
re-assemble equipment according to instruction procedures. Be sure all components are firmly screwed or latched into position.
only to tap water outlets (75 PSI maximum).
ALWAYS
ATTACH
Installation and Operation:
1. Select a metering tip (see next section), and insert it into the suction stub. Slide the open end of the suction tube through the
bung adaptor, then over the suction stub.
2. Slide end of discharge tube over the eductor discharge outlet.
3. Remove either the 3/4 or 2-inch bung from an upright drum.
4. Insert the foot valve end of the suction tube into the drum.
5. Swivel the drum adapter several turns in the bung opening until the bracket is secure.
6. Install minimum 1/2-inch ID water hose between the inlet swivel and water supply spigot. (Minimum 25 PSI flowing water
pressure is required to operate the unit.)
7. Turn on water supply. To begin dispensing solution, open ball valve at inlet to unit. Do not keep discharge hose in liquid! The
concentrate will siphon from the container.
Metering Tip Selection:
The final concentration of the dispensed liquid is related to both the size of the metering tip opening (orifice) and the
viscosity of the liquid being siphoned. If product viscosity is noticeably greater than that of water, consult the procedure for
Measurement of Concentration on the next page to achieve your desired water-to-product ratio. For waterthin products, use
the chart below as a guideline. Because such factors as inlet water pressure and temperature can affect dilution ratios, the
figures listed below are only approximate. Test the actual dilution you are achieving using the Measurement of Concentration
procedure for best results. Two undrilled, clear tips are supplied for drilling sizes not listed.
Decimal
Equivellent
Approximate Dilution Ratio at
40 PSI, water-thin viscosity (1.0 cp)
4.5:1 or 22.2%
Tip Color
No tip
Gray
Black
Beige
Red
White
Blue
Tan
Green
Orange
Brown
Yellow
Purple
Pink
Drill Size
30
40
50
55
57
60
65
70
72
74
76
80
87
.1285
.0980
.0700
.0520
.0430
.0400
.0350
.0280
.0250
.0225
.0200
.0135
.0100
5:1
6:1
9:1
20.0
16.6
11.1
5.0
20:1
24:1
26:1
31:1
50:1
70:1
90:1
100:1
200:1
400:1
4.16
3.84
3.23
2.0
Copyright 2008
Zebra Skimmers Corp.
PO Box 833
Chagrin Falls, OH 44022
888-249-4855
1.43
1.11
1.0
.50
.25
Printed in the USA • Revised February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|