REFRIGERATOR
ZUD 9154
INSTRUCTION BOOKLET
2222683-22
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings of these warnings contact the Customer Care Department.
Prior to Installation
General Safety
■ Check the appliance for transport damage. Under
no circumstance should a damaged appliance be
installed. In the event of damage please contact
your retailer.
■ This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging
must therefore only be carried out by autho-
rised technicians.
■ Take utmost care when handling your appli-
ance so as not to cause any damages to the
cooling unit with consequent possible fluid
leakages.
Installation
■ This appliance is heavy. Care should be taken
when moving it.
■ The appliance must not be located close to
■ It is dangerous to alter the specifications or
radiators or boilers.
attempt to modify this product in any way.
■ Avoid prolonged exposure of the appliance to
■ Ensure that the appliance does not stand on the
electrical supply cable.
direct sunlight.
■ Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating appli-
ances.
Important: if the supply cable is damaged, it
must be replaced by authorized service or quali-
fied personnel using a special cable of the same
type.
During Use
■ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs. It is
not intended for commercial or industrial use.
■ Any electrical work required to install this appli-
ance should be carried out by a qualified electri-
cian or competent person.
■ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the installa-
tion instructions.
■ Containers with flammable gases or liquids can
leak at low temperatures. Do not store any con-
tainers with flammable materials, such as spray
cans, fire extinguisher refill cartridges etc. in the
refrigerator.
■ The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Maintenance and Cleaning
■ Before cleaning, always switch off the appliance
Refrigerant
and disconnect from the electrical supply.
■ The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
■ When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Servicing
■ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
■ During transportation and installation of the appli-
ance, be certain that none of the components of
the refrigerant circuit become damaged.
■ If the refrigerant circuit should become damaged:
- avoid open flames and sources of ignition.
- thoroughly ventilate the room in which the
appliance is situated.
■ Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local Service
Force Centre.
Child Safety
■ Do not allow children to tamper with the controls
At the end of the Appliance Life
■ When disposing of your appliance use an autho-
or play with the product.
■ There is a risk of suffocation! Keep packaging
rised disposal site.
material away from children!
■ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF THE APPLIANCE
Dairy compartment
Movable shelf
➀
➁
➂
➃
➄
➅
➅
➀
Bottle storage shelf
Salad bin
Storage shelves
Thermostat control
➁
➄
➃
➂
OPERATION
Before use
hours for the temperature to stablise before making
further changes.
Remove all securing tapes. Wash inside the appli-
ance with lukewarm water and bicarbonate of soda
(5 ml to 0.5 litre of water). Do not use soap or deter-
gent as the smell may linger. Dry thoroughly.
Important
During prologed periods of abnormally hot
weather, if the thermostat is seto on too high a
number, the cooling system may operate con-
tinuously and the fridge coolilng plate may not
defrost. Turning the knob to a lower number
will cause the automatic defrosting to resume.
If you wish to return to a lower temperature,
turn the thermostat knob to a higher number,
however you should turn the setting lower
occasionally to allow automatic defrosting.
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat control knob with 6 temperature
positions and one «OFF» (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat control knob to the required
position.
An intermediate position is usually the most suitable,
although the temperature will be affected by:
Fresh food refrigeration
l
Room temperature
l How often the door is opened
l How much food is stored
l Position of the appliance
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not cover the shelves with any protective materi-
al, such as paper, cardboard or plastic, which may
obstruct the air circulation through them.
In determining the correct temperature control set-
ting all these factors have to be considered and
some experimentation may be necessary.
When altering the temperature setting, allow 24
4
Download from Www.Somanuals.com. All Manuals Search And Download.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & poultry): wrap in
polythene bags and place on top of the salad draw-
ers.
Meat can only be stored safely in this way for one
or two days at the most.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad drawers.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
The walls of the refrigerator are equipped with run-
ners so that shelves can be positioned as desired.
For better use of space, the front half-shelves can lie
over the rear ones (see fig.).
D338
The door shelves
To permit storage of food packages of various sizes
the half tray can be adjusted in horizontal.
To do this proceed as figure.
For more thorough cleaning, the top door shelf and
the bottle shelf can be removed by pulling them in the
director of the arrows, then refitting them in position.
Normal Operating Sounds
You may hear faint gurgling or bubbling sounds when
the refrigerant is pumped through the coils below, to
the cooling evaporator.
When the compressor is on, the refrigerant is being
pumped round, and you will hear a whirring sound or
pulsating noise from the compressor. A thermostat
controls the compressor, and you will hear a faint
‘click’ when the thermostat cuts in and out.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HEALTH AND SAFETY GUIDELINES
Because of consumer demand, preservatives have been removed from many pre-prepared foods. This
together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure that
the food in your home is in as perfect condition
as possible.
■
■
■
Keep the time between buying chilled food and
placing it in your fridge as short as possible. Tests
showed that the temperature of 1 litre of orange
juice rose to 22°C in an hour between the super-
market and home. It then took 11 hours to get
down to 7°C in the refrigerator.
Never allow spillages to dry and harden.
Store eggs in the egg rack provided in the refrig-
erator door. Discard any broken or chipped eggs.
■
■
■
Regularly check the refrigerator door seal to
ensure that it is clean and free from debris.
■
■
■
Keep the refrigerator door closed as much as pos-
sible.
Always wash your hands with soapy water and
dry them with a clean towel before handling food.
Do not push food together too much, try to allow
air to circulate around each item.
Keep work surfaces clean and avoid cross conta-
mination by not using the same work surface or
knife, without washing them thoroughly in
between.
Cool cooked food as quickly as possible but do
NOT place in the refrigerator until cool. (Leave
food in a cool place in order that it can then be
placed in the refrigerator as soon as possible).
■
Do NOT mix raw and cooked meat, they must be
in separate containers. Take care not to let the
meat juices drip onto other food. If the meat does
drip, remove everything and clean thoroughly.
■
■
Do not store food uncovered.
Remove suspect food from your refrigerator and
clean (Refer to “Maintenance and Cleaning”).
DEFROSTING
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located below the appliance, where it
evaporates.
Important
To avoid defrost water overflowing and dripping
onto the food in the fridge, periodically clean
the water discharge hole (F) situated under the
salad drawers. Use the special cleaner provid-
ed (P) which you will find already inserted into
the discharge hole
P
F
S.I.011
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the ELEC-
TRICITY supply.
1. Unscrew the light cover and then pull it outward
by pressing as shown in the figure. Unscrew the
bulb and replace it with a new 15 watt bulb (avail-
able from your nearest Zanussi Service Force
centre).
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
D411
NEVER USE DETERGENTS, ABRASIVE POW-
DERS, HIGHLY PERFUMED CLEANING PROD-
UCTS OR WAX POLISHES, TO CLEAN THE INTE-
RIOR AS THESE WILL DAMAGE THE SURFACE
AND LEAVE A STRONG SMELL.
2. Replace the light cover by sliding it into its original
position and replacing the screw.
Clean the drain hole of the water trough at regular
intervals and make sure that the drain hole is never
obstructed, so that the defrost water may flow freely.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the door ajar
to prevent unpleasant smells.
Important
Do not use abrasive products.
Periodic cleaning
The appliance is equipped with a ventilation grid.
Keep clean to guarantee good ventilation and good
working order of the appliance.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity con-
sumption.
The structure of the appliance permits cleaning of
the rear zone close to the wall, using a vacuum
cleaner.
3
2
1
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3), checking
S.I.013
that there is no water left from the defrosting.
Changing the light bulb
Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SOMETHING NOT WORKING?
Before contacting your local Service Force Centre check the following points.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Solution
No power to appliance
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
The light does not come on
- Ensure that the bulb is correctly fitted.
- Replace the bulb if it has blown.
- Check the door light switch is not jammed.
The temperature in the fridge or freezer section is too
high
- Check the ambient temperature is within the appliances
operating limits of 10˚C to 38˚C.
- Check the thermostat knob is turned to the correct
setting relative to ambient conditions.
The compressor runs continuosly
Excessive frost and ice has built up
- Adjust the thermostat knob to give correct temperature
control. See page 4.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
- Ensure the door is not left open.
- Check that nothing is preventing the door from closing.
- Is the door gasket intact and clean.
Noise
- Refer to normal operating sounds.
Water under the salad drawers
- Check the drain hole is not blocked (see Maintenance
and Cleaning).
If after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND SPARE PARTS
Before calling out an engineer, please ensure you
have read the details under the heading ‘Something
Not Working’.
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
When you contact the Service Centre you will need
to give the following details.
08705 929929
1. Your name, address and post code
2. Your telephone number
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
The addresses are listed on the following pages.
3. Clear and concise details of the fault
4. The model serial no. of the appliance (found on
the rating plate)
5. The purchase date
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you
are invited to contact our Customer Care Department by letter or telephone or visit our website at
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 ( )
*
( ) calls to this number may be recorded for training purposes.
*
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part there-
of is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
■
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
■
The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's
instructions.
■
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
■
■
■
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
■
■
■
■
Damage or calls resulting from transportation, improper use or neglect, thc replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
■
The guarantee starts from the date you first purchased your product.
■
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
■
■
■
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
■
The product is installed taking in account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 44 62 29 99
+49 (0) 911 323 2600
+39 (0) 1678 47053
+46 (0) 8 738 79 50
+44 (0) 1753 219897
Nurenberg
Pordenone
Stockholm
Slough
Sweden
UK
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
Width
Depth
81,5
59,6
54
cm
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
70 W
AVERAGE DAILY UNITS ELECTRICITY (*)
0,47 kWh
GROSS CAPACITY
NET CAPACITY
142 l
140 l
(*)This figure is based on standard test results in accordance with European Standard EN153. Actual con-
sumption will depend on how the appliance is used and where it is located.
INSTALLATION
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located on the inside left of the appliance.
The following table shows which ambient temperature
is correct for each climate classification.
SN +10°C to +32°C
ST +18°C to +38°C
The appliance should be located in a dry atmosphere,
out of direct sunlight and away from continuous heat
and extreme temperature, e.g. not next to a boiler or
radiator, or in a very cold room e.g. an outhouse. If
these temperatures are exceeded i.e. warmer or cold-
er, then the appliance may not operate correctly.
For building-in and door reversal instructions please
refer to the relevant instructions on the following
pages.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTION
This appliance complies with the E.E.C.
WARNING:
Directive No. 87/308 of 2.6.87 relative to radio
interference suppression.
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be observed.
A replacement cover/carrier must be obtained
from your local Zanussi Service Force Centre.
If the plug that is fitted to your appliance is not suit-
able for your socket outlet, it must be cut off and the
appropriate plug fitted.
This appliance complies with the following
E.E.C. Directive:
Remove the fuse from the cut off plug.
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent amend-
ments.
The cut off plug should then be disposed of to prevent
the hazard of shocks in case it should be plugged into
a 13amp socket in another part of your home.
Important
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of breakdown.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
GREEN & YELLOW
13 AMP. FUSE
«E» or the earth symbol
yellow.
, or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or colured
red.
BROWN
BLUE
CORD CLAMP
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
D207
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BUILDING-IN INSTRUCTIONS
Before carrying out any work, remove the plug from
the power socket.
Grid preparation
Left door opening:
Remove the left side (A) of the grid cutting it from the
rear (see figure).
A
Right door opening:
Remove the right side (B) of the grid cutting it from
the rear (see figure).
B
DO002/2
To position the grid on the appliance proceed as fol-
lows:
Apply the grid to the base of the appliance by pushing
the clasps (a) until they click.
a
a
DO001
Door reversal
To reverse the opening direction of the door, proceed as shown
in the figures:
6
4
1
7
8
5
3
2
1
2
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention
After completion of the door reversing opera-
tion, check that the door gasket adheres to the
cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural fit-
ting of the gasket or accelerate this process by
heating up the part involved with a normal
hairdryer on a low setting.
10
13
9
12
11
3
Building in the appliance under a worktop
1. The dimensions of the recessed installation area
must correspond with those indicated in the figure.
DO013
2. Installation kit
1xB
2xC
1xA
12
2
2
2
1
1
1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Two cabinet securing brackets are supplied with
the installation pack. They need to be assembled
onto the cabinet prior to cabinet being pushed into
the Kitchen aperture.
- To fit these brackets remove the two screws at the
top left and right hand front corners of the cabinet.
- Position the two brackets as shown in the figure
and replace the two securing screws.
Left hand
bracket
Right hand
bracket
4. Push the appliance into place. The plug socket
necessary for connection of the appliance to the
electricity supply should be positioned, so that the
plug is not placed in the recess.
5. To adjust the height proceed as follows:
- Loosen or tighten the two front feet.
- The rear feet are adjusted by turning the screw in
the front kick plate to the left or right.
-
+
6. If necessary, pads are supplied for the rear feet to
make sliding the appliance in and out of the recess
easier. To fit the pads, press them onto the rear
feet.
If required, the dimensions of these pads can be
reduced by breaking them where marked.
II52
2
1
B
115°
3
4
N.B. The joint cover (B) is to be assembled after hav-
ing installed the appliance in the recess.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Screw appliance into place and retain the cabinet
with screws through the securing brackets into the
worktop or adjacent woodwork as necessary.
8. To mount the furniture door proceed as shown in
the figures:
2
1
a
10
C
4
3
b
6
a
b
C
clic
C
clic
c
7
8
18
Download from Www.Somanuals.com. All Manuals Search And Download.
UPPER PART OF KITCHEN FURNITURE PANEL
1
a
=
=
LOWER PART OF KITCHEN FURNITURE PANEL
2
275
275
max 100
b
9/a
9
1
2
45
°
=
=
10
3
11
10
12
19
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Refit the covering strip.
A
13
Fitting the plinth
Important
For the efficient operation of the appliance, it is
important that the original ventilation grid is
used.
■ For an opening height dimension A=820 mm and a
plinth height dimension a=100 mm, the plinth may
be fitted without adjustments. The same applies to
an opening height dimension B=870 mm and a
plinth height dimension b=150 mm.
■ For plinth heights greater than a=100 mm, b=150
mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the appliance position, leav-
ing a remaining height of a=100 mm, b=150 mm.
■ Attach plinth to the kitchen units.
25
Important
DO008
The plinth must be positioned at a minimun dis-
tance of 25 mm from the door.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Electrolux Household Appliances Limited 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|