Dishwasher
ZSF 6171
User information
g
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagram of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
6
7
Prior to Using for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Water Softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
9
Adding dishwasher Salt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Filling Up with Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
In daily use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Loading cutlery and dishes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Height of the Upper Basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adding Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using 3in1 detergents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Selecting the dishwashing cycle (Cycle Table) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Starting a Dishwashing Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the Delay Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Switching Off the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Care and cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Remedying small malfunctions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
If the dishwashing results are not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Notes for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation and connection instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Safety Information for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the Dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Connecting the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Warranty conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Service and Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and con-
nection”.
Correct Use
• The dishwasher is only intended for washing do-
mestic dishes.
• Additions or modifications to the dishwasher are
not permitted.
• Use only special salt, detergent and rinse aid suita-
ble for domestic dishwashers.
• Do not put any solvents in the dishwasher. This
could cause an explosion.
Child Safety
• Keep packaging away from children. There is a risk
of suffocation.
• Children often do not recognise the hazards asso-
ciated with electrical appliances. Don’t allow chil-
dren to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into
the dishwasher. Could endanger life!
• Dishwasher detergents can cause chemical burns
to the eyes, mouth and throat. Could endanger life!
Comply with the safety instructions of the dish-
washer detergent manufacturer.
• The water in the dishwasher is not for drinking.
Risk of chemical burns.
General Safety
• Repairs to the dishwasher are only to be carried
out by qualified/authorised service engineers.
• When the dishwasher is not being used, switch it
off and shut off the water tap.
• Never unplug the appliance by pulling on the ca-
ble. Always pull the plug.
• Ensure that the door of the dishwasher is always
closed when it is not being loaded or unloaded. In
this way you will avoid anybody tripping over the
open door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there
may be a frost, remove the connection hose from
the tap after each use of the dishwasher.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dishwasher door safety catch
The dishwasher door has a safety catch which pre-
vents children opening the dishwasher door by mis-
take.
The door safety catch is set as follows:
1.There is a lever (1) on the lefthand side of the door
handle recess. You can secure the dishwasher
against accidental opening by moving the lever to
the right until a click is heard (for example, with the
handle of a spoon).
2.If the safety catch is engaged, to open the dish-
washer you must
– first move the door lever to the left (2) until a slight
resistance is felt and a click is heard.
– then open the door as normal (3).
3.You can disengage the dishwasher’s door safety
catch by pressing the lever all the way to the left
with your finger.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagram of Appliance
Top Spray Nozzle
Upper basket spray arm
and lower spray arm
Water softener
unit.
Salt Container
Detergent
Dispenser
Rinse aid
dispenser
Rating plate
Filters
Interior lighting
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
ON/OFF button
Programme buttons
1
2
3
Function buttons
The ON/OFF button is used to turn the dishwasher
on and off.
The Programme buttons are used to select the de-
sired dishwashing cycle.
Function buttons: In addition to the pre-set dish-
washing cycle, the following functions can also be
set using these buttons:
Function button 1
Function button 2
Function button 3
Set the water softener
Activates/deactivates rinse
aid dispenser when 3in1 on
- not programmed -
The rinse aid inflow is only affected, if the 3in1 func-
tion is selected.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-display
Programme progress display
Control
indicators
Select Care Plus
function
Set delay
timer
Select
3 in1 function
The multi-display can indicate:
– the level of hardness to which the water softener is
set.
– whether the rinse aid dispenser has been activat-
ed/deactivated.
– the start delay that has been set.
– the estimated time remaining for the current dish-
washing cycle.
– what type of error has occurred with the dishwash-
er.
Programme progress display: The current stage of
the programme is always shown in the programme
progress display.
The control indicators have the following meanings:
1)
Salt
Refill with special salt
Refill with rinse aid
Turn on the tap
1)
Rinse Aid
Water
Clean the dishwasher's filter sys-
tem
Filter
Door
The door of the dishwasher is
open
1) These control indicators are never illuminated while a dish-
washing cycle is running.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Prior to Using for the First Time
3
If you wish to use 3 in 1 detergent:
– First read the section “Using 3in1 deter-
gents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the
first time
1.Set the water softener
2.Fill up with dishwasher salt
3.Fill up with rinse aid
Setting the Water Softener
The water softener must be set manually and elec-
tronically:
3
To avoid scale deposits on the dishes and in
the dishwasher, the dishes must be washed
with soft water, i.e. water with a low lime con-
tent. The water softener must be set according
to the table to the water hardness in the area
where you live. Your local water company will
be able to give you information about the wa-
ter hardness in your area.
The dishwasher must be switched off.
Setting manually:
1.Open the dishwasher door.
2.Remove the lower basket from the dishwasher.
3.Turn water hardness dial on the left wall of the
dishwasher interior to O or 1 (see table).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting electronically:
1.Press the ON/OFF button.
3
If indicators for the programme buttons are lit,
a dishwashing cycle is activated. The dish-
washing cycle must be deselected:
Press function buttons 1 and 2 simultaneously
for approx. 2 seconds.
All additional wash programme button indica-
tors will go out.
2.Press function buttons 1 and 2 simultaneously and
keep them pressed.
The LED indicators for function buttons 1 to 3 will
flash.
3.Press function button 1.
The LED indicator for function button 1 will flash.
The multi-display will indicate the hardness setting.
4.Pressing function button 1 increases the hard-
ness setting by 1.
(Exception: hardness setting 1 follows hardness
setting 10).
5.When the hardness setting is correct, press the
ON/OFF button.
The hardness setting is now saved.
If the water softener is set electronically to “1”, this
switches off the control indicator for dishwasher salt.
Water hardness
Adjusting the hardness setting
Indication on the
multi-display
1)
2)
in °d
in mmol/l
Range
Manual
Electronic
3)
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
10
10L .
9L
9
8
7
6
IV
1
8L
7L
6L
19 - 22
15 - 18
3,3 - 3,9
2,6 - 3,2
5
4*
5L
4L
III
11 - 14
4 - 10
1,9 - 2,5
0,7 - 1,8
II
3
2
3L
2L
0*
I/II
1
below 4
below 0.7
I
1L
no salt necessary
1) (°d) German degree, measure of the hardness of water
2) [mmol/l] millimol per litre, international unit for water hardness
3) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding dishwasher Salt
To decalcify the water softener, it must be filled up
with dishwasher salt. Use only special salt suitable
for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with dish-
washer salt:
– Before using the dishwasher for the first time.
– When the control indicator for dishwasher salt is il-
luminated on the control panel.
1.Open the door and remove the lower basket.
2.Unscrew the lid on the salt dispenser by turning it
anti-clockwise.
3.Only when using the dishwasher for the first
time:
Fill the salt dispenser with water.
4.Place the funnel (supplied) over the dispenser
opening.
Fill the dispenser with dishwasher salt; the capaci-
ty of the dispenser is approx. 1.0-1.5 kg, depend-
ing on the size of the grains. Do not overfill the
dispenser.
3
If water overflows when filling up with dish-
washer salt, this is completely harmless.
5.Clean away any salt remnants from the dispenser
opening.
6.Screw the lid back on in a clockwise direction.
7.Run a dishwashing cycle after filling the salt
dispenser with dishwasher salt. This will wash
away salt water and salt crystals that have been
spilt.
3
Depending on the size of the salt granules, it
can take several hours for the salt to dissolve
in the water and for the control indicator for
dishwasher salt to go out.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling Up with Rinse Aid
Rinse aid causes the rinse water to flow easily from
the crockery leaving gleaming dishes and glassware.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– When the control indicator for rinse aid is illuminat-
ed on the control panel.
Use only special rinse aid for dishwashers.
1.Open the door.
The rinse aid compartment is located on the inside
of the dishwasher door.
2.Press the release button on the rinse aid compart-
ment.
3.Open the cover.
4.Pour rinse aid in slowly right up to the broken
“max” line;
this corresponds to a volume of approx. 140 ml
when full.
5.Press the lid shut until it clicks into place.
6.Wipe up any spilt rinse aid with a cloth. Otherwise
there will be too much foam when rinsing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Amount of Rinse Aid
Required
3
Only change the amount dispensed, if smears,
milky spots (reduce the amount) or dried on
water spots (increase the amount) can be seen
on glasses and dishes. (See section “If dish-
washing results are not satisfactory”.) The
dosage can be set from 1-6. The dosage is
pre-set to “4” in the factory.
1.Open the dishwasher door.
2.Press the release button on the rinse aid compart-
ment.
3.Open the cover.
4.Set the dosage level.
5.Press the lid shut until it clicks into place.
6.If rinse aid has leaked out, wipe it away with a
cloth.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating rinse aid inflow
when 3in1 function is selected
3
If the 3in1 function is not selected, the rinse
aid inflow is always activated.
If the 3in1 function is selected due to the use of 3in1
detergent, the rinse aid inflow is deactivated. If the
dishes then do not dry sufficiently, you should re-ac-
tivate the rinse aid inflow (see also section “Using
3in1 detergents”).
1.Press the ON/OFF button.
3
If the LED indicator of only one programme
button is illuminated, this wash programme
has been activated. The wash programme
must be deselected:
Press function buttons 1 and 2 simultaneously
for approx. 2 seconds.
The LED indicators of all the programme but-
tons that can be selected will illuminate.
2.Press function buttons 1 and 2 simultaneously and
hold them down.
The LED indicators for function buttons 1 to 3 will
flash.
3.Press function button 2.
The LED indicator for function button 2 will flash.
The multi-display will indicate the current setting:
Rinse aid inflow deactivated when
3in1 on (factory setting)
0d
Rinse aid inflow activated when 3in1
on
1d
4.Pressing function button 2 activates and deacti-
vates the rinse aid dispensing function.
5.Once the multi-display is indicating the required
setting, press the ON/OFF button. The setting is
now saved.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
In daily use
Loading cutlery and dishes
1
Sponges, cleaning cloths and any other ob-
jects that can absorb water must not be
washed in the dishwasher. Plastic and Teflon-
coated dishes and pans tend to retain water
droplets. These dishes and pans therefore do
not dry as well as those made of china and
stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or moth-
er of pearl handles
• Only wash stoneware in the dishwasher if it is specifically
marked by the manufacturer as being dishwasher-safe.
• Glazed patterns may fade if washed very frequently in the
dishwasher.
• Silver and aluminium parts have a tendency to discolour dur-
ing washing. Food remains, e.g. egg white, egg yolk and
mustard often cause discoloration and staining on silver.
Therefore always clean food residues from silver immediately,
if it is not to be washed straight after use.
• Plastic items that are not heat resistant
• Older cutlery with cement
that is sensitive to temperature
• Dishes or cutlery with glued parts
• Pewter or copper items
• Lead crystal glass
• Steel items that rust
• Wooden boards/platters
• Items made from synthetic materials
• Glass can become dull after a large number of washes.
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnt-on food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation
of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the
opening downwards so that water cannot collect
in them
– Dishes and items of cutlery must not lie inside
one another or cover one another
– To avoid damage to glasses, they must not touch
one another
– Don’t put small items (e.g. lids) in the baskets for
the dishes, but in the cutlery basket, so that they
can’t fall through the holes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading cutlery
1
Warning: Sharp knives and other items of cut-
lery with sharp edges must be laid in the cut-
lery rack or in the upper basket because of the
risk of injury.
To ensure that all items of cutlery in the cutlery bas-
ket can be reached by the water, you should:
1.Place the grid insert on the cutlery basket
2.Place forks and spoons in the cutlery basket's grid
insert with their handles pointing downwards.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and pans in the
lower basket.
(Max. diameter for plates 29 cm).
To make it easier to load larger dishes, the two rear
plate rests in the lower basket can be folded down
and the cutlery basket in the lower basket can be
moved to the side.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long, sharp cutlery
in the upper basket.
• Arrange items of crockery on and under the folding
cup racks so that they are offset from each other
and water can reach all items.
• The cup racks can be folded up out of the way for
tall crockery items.
• Lay or hang wine and brandy glasses in the slots in
the cup racks.
• For glasses with long stems, fold the glass rack to
the right, otherwise fold it away to the left.
• The row of spikes on the left of the upper basket is
also in two parts and can be folded away.
Spikes not folded away: place glasses, mugs etc.
in the upper basket.
Spikes folded away: More room for serving
dishes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Height of the Upper Basket
Maximum height of dishes in the
Upper basket
Lower basket
with upper basket raised
with upper basket lowered
22 cm
24 cm
30 cm
29 cm
3
The height of the baskets can also be adjusted
when they are loaded.
Raising / Lowering the upper basket
1.Pull out the upper basket completely.
2.Holding the upper basket by the handle, raise it as
far as it will go and then lower it vertically.
The upper basket will latch into the lower or the
upper position.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Detergent
Detergents remove the dirt from dishes and cutlery.
The detergent must be added before the cycle starts.
1
Only use detergent intended for domestic
dishwashers.
The detergent compartment is located on the inside
of the door.
1.If the lid is closed:
Press the release button.
The lid will spring open.
2.Place the detergent in the detergent dispenser. The
markings indicate the dosing levels for powder de-
tergents: “20/30” corresponds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions with regard
to dosing and storage.
3.Close the lid and press until it locks into place.
3
In the case of very heavily soiled dishes, fill the
adjoining compartment (1) with additional de-
tergent. This detergent comes into use during
the pre-wash cycle.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Concentrated detergents
Today’s detergents for dishwashers are almost ex-
clusively low-alkaline concentrated detergents with
natural enzymes in tablet or powder form.
2
Using 50°C dishwashing cycles in conjunction
with these concentrated detergents reduces
pollution and is good for your dishes, as these
dishwashing cycles are specially matched to
the dirt-dissolving properties of the enzymes
in concentrated detergents. It is for this reason
that using 50 °C dishwashing cycles in con-
junction with concentrated detergents can
achieve the same cleaning results that can
otherwise only be achieved using 65 °C cy-
cles.
Detergent tablets
3
Detergent tablets from different manufactur-
ers dissolve at different rates. For this reason,
some detergent tablets do not attain their full
cleaning power during short cycles. Therefore
please use dishwashing cycles with pre-wash
when using detergent tablets.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using 3in1 detergents
These products are detergents with a combined
cleaning, rinsing and salt function.
• Then set the water softener to the water hardness
in your area.
When the 3in1 function is activated,
– the addition of special salt and rinse aid from the
respective dispenser is prevented.
– If the salt and rinse aid dispensers are empty, this
is not indicated.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also
anti- glass corrosion agent into "3 in 1" formula,
please follow the same indication as given for "3 in
1" detergents.
– The dishwashing cycles can be up to 30 minutes
longer.
3
If you want to use 3in1 detergents, check
whether these detergents are suitable for your
water hardness. (Follow manufacturer’s in-
structions!)
If your water hardness is higher than that rec-
ommended by the manufacturer but you
would nevertheless like to use 3in1 detergent,
proceed as follows:
• With the 3in1 function selected, set the water sof-
tener one hardness setting lower than when rinsing
without 3in1 detergent.
• Fill up the dispenser (if this is empty) with special
salt.
The dishwasher remembers the two different set-
tings of the degree of hardness for rinsing with and
without 3in1 function.
If you want to use 3in1 products
1.Press the ON/OFF button.
2.Press the 3 IN 1 button.
The button indicator lights up: 3in1 function is se-
lected.
Before the start of the dishwashing cycle put 3in1
detergent in the detergent dispenser.
3
As the rinse aid inflow is automatically
switched off when the 3in1 function is activat-
ed, it may come about because of the different
quality standards in the 3in1 detergent, that
the dishes do not dry sufficiently.
If this happens, proceed as follows (see sec-
tion “Adding rinse aid”):
• Fill up the dispenser (if this is empty) with rinse aid.
• Set rinse aid dosage to “2” mechanically.
• Activate rinse aid inflow.
If you do not want to use 3in1 products
any more
If you want to stop using 3in1 products, please do
the following:
• Deactivate the 3in1 function.
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting
and perform up to three normal cycles without
loading any dishes.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the dishwashing cycle (Cycle Table)
Programme
sequence
Consumption-
1)
values
Dishwashing-
cycle
Suitable
for:
Type of
soiling
Automatic
50°-65°
Dinner service and
cookware
normally soiled,
dried-on food remains
•
•
•
•
2)
heavily soiled,
Intensive
70°
Dinner service and
cookware
dried-on food remains, in
particular protein and
starch
•
-
•
•
•
•
•
•
•
-
Quick Wash
Dishes, excluding
saucepans
just used, lightly to nor-
mally soiled
-
3)
60°
Dinner service and
cookware, tempera-
ture-sensitive crock-
ery
Economy
normally soiled
•
•
•
4)
50°
Dessert dishes and
coffee service, deli- lightly soiled
cate glassware
Delicate
45°
-
•
•
•
Used dishes that are be-
Prewash
(cold)
ing stored in the dish-
washer and are to be
washed later.
All types of dishes
•
-
-
-
-
5)
1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are.
Variations are therefore possible in practice.
2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and
water and energy consumption can vary greatly – depending upon the load and how dirty the dishes are. Depending upon the
soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C.
3) When using this cycle, only load the dishwasher half full.
4) Test programme for Test Institutes
5) This cycle does not need any detergent.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energy-saving programme.
a short programme (e.g. 30 minute programme).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting a Dishwashing Cy-
cle
1.Check that the spray arms can turn freely.
2.Turn the water tap on fully.
3.Close the door.
4.Press the ON/OFF button.
5.Select the desired cycle.
The cycle indicator and the respective cycle stages
in the cycle progress display will be illuminated.
The remaining time expected for the cycle will be
shown in the multi-display.
The selected cycle will begin after approximately 3
seconds.
The current stage of the cycle is always shown in
the cycle progress display.
3
During the dishwashing cycle, the remaining
time shown in the multi-display may be adjust-
ed according to the size of the load, degree of
soiling, etc.
Interrupting or Cancelling a dish-
washing cycle
Interrupt a dishwashing cycle that is in progress if it
is absolutely necessary.
Interrupting the dishwashing pro-
gramme by opening the dishwasher door
1
Hot steam may escape when the door is
opened. There is a risk of scalding.
1.Open the door carefully. The dishwashing cycle will
stop.
2.Close the door. The cycle will continue.
Cancelling the wash programme
1.Press function buttons 1 and 2 and hold them
down.
The LED indicators of all the programme buttons
that can be selected will illuminate.
2.Release the function buttons. The wash pro-
gramme has been cancelled.
3.If you want to start a new wash programme, check
whether there is any detergent in the dispenser.
4.Switch off using the ON/OFF button.
3
Turning off the dishwasher will only interrupt a
selected dishwashing cycle, not cancel it. The
cycle will recommence after turning the dish-
washer back on again.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Delay Timer
Switching Off the dish-
washer
3
With the delay timer you can delay the start of
a dishwashing cycle for between 1 and 19
hours.
Only switch the dishwasher off when the multi-dis-
play indicates “0” for the cycle time remaining and
the end of programme indicator is illuminated.
1.Press the ON/OFF button. All display indicators will
go out.
1.Press the Delay Timer button repeatedly until the
multi-display shows the desired time delay, for ex-
ample 12h, if the cycle is to start in 12 hours. The
Delay Timer indicator is illuminated.
2.Turn off the water tap.
2.Select dishwashing cycle.
1
Carefully open the door. Hot steam may es-
cape.
3.The time remaining to the start of the cycle is con-
tinuously displayed (e. g. 12h, 11h, 10h, … 1h etc.).
To change the time delay:
As long as the cycle has not yet started, you can still
change the setting by pressing the DELAY TIMER
button.
• Hot dishes are sensitive to knocks. Therefore leave
the dishes to cool for about 15 minutes before re-
moving them. You also get a better drying result.
• Dishes dry more quickly if you open the door for a
moment after the cycle has ended and then leave it
slightly open.
Cancelling the time delay:
Press the Delay Timer button repeatedly until the
length of the selected cycle appears in the multi-dis-
play. The selected dishwashing cycle will begin im-
mediately.
Removing the Dishes
To change a dishwashing cycle
3
It is normal for the inner door and the dispens-
ers to be damp.
As long as the cycle has not yet started, you can still
change the dishwashing cycle. First cancel the dish-
washing cycle, then re-set the time delay, lastly se-
lect the new dishwashing cycle.
• Empty the lower basket first, then the upper bas-
ket. This way you avoid dripping water from the
upper basket onto dishes in the lower basket.
• The dishwasher's interior light will always be on
when the door of the appliance is open. Therefore,
in order to save energy, you should always close
the door of the dishwasher after having loaded or
removed dishes.
Care Plus additional function
This additional function makes it possible to hygieni-
cally clean items such as plastic chopping boards or
jam jars.
It can be selected as an extra to all dishwashing cy-
cles. (Exception: Glass cycle and Pre wash, if availa-
ble.)
1.Switch on the appliance.
2.Press the programme button for the programme
required (see “Cycle Table”).
Within 3 seconds press the button for the addition-
al function Care Plus.
The Care Plus additional function indicator lights
up.
In the last rinse cycle the temperature will now be
held at over 65° C for at least 10 minutes.
3.When the cycle has finished, the Care Plus addi-
tional function is automatically switched off again.
The Care Plus indica-
tor is lit:
Additional function
switched on
The Care Plus indica-
tor is not lit:
Additional function
switched off
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning
1
Do not use furniture care products or aggres-
sive cleaners.
• When necessary, clean the dishwasher’s controls
with a soft cloth.
• Occasionally check the internal dispensers, door
seal and water inlet filter (if fitted) for dirt and clean
them, if necessary.
Cleaning the filters
3
The filters must be regularly checked and
cleaned. Dirty filters will spoil the wash
results.
1.Open the door and remove the lower basket.
2.Turn the handle about ¼ of a turn anticlockwise (A)
and remove the filter system (B).
3.Grasp the grip hole on the fine filter (1) and remove
it from the micro-filter (2).
4.Clean all filters thoroughly under running water.
5.Remove the flat filter (3) from the base of the wash-
ing compartment and clean both surfaces thor-
oughly.
6.Re-insert the flat filter.
7.Place the fine filter in the micro-filter and fit the two
together.
8.Insert the filter system in place and lock it by turn-
ing the handle clockwise as far as it will go. Ensure
that the flat filter does not protrude above the base
of the washing compartment.
1
Under no circumstances may the dishwasher
be used without its filters.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the spray arm jets
Regularly check the jets in the spray arms for
blockages. When cleaning is necessary, re-
move spray arm from the fixture and clean jets
with a pointed object (wire or needle). Then
rinse out the spray arm using a strong jet of
water.
3
Do not damage the jet opening.
Upper basket spray arm
1.To remove upper basket spray arm, tilt it down
hard.
2.Clean spray arms jets.
3.Place cleaned upper basket spray arm back in po-
sition against the connecting piece: press the two
together firmly, until you feel them snap into place.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Bottom spray arm
1.To remove bottom spray arm, pull it upwards out of
its catch.
2.Clean spray arm jets.
3.Place bottom spray arm back in position against
connecting piece and press down firmly, until you
feel it snap into place.
What to do if...
Remedying small malfunc-
tions
If one of the following fault codes is displayed in the
multi-display during operation:
– Fault codeÅ10 (Problems with water inlet),
– Fault codeÅ20 (Problems with water drainage),
please have a look at the following table.
When the fault is remedied, press the button for the
cycle that has started. The cycle will continue.
With other fault codes (“Å” followed by a number):
– Abort the dishwashing cycle.
– Switch the appliance off and on again.
– Re-set the dishwashing cycle.
If the fault is displayed again, please contact your lo-
cal Service Force Centre and inform them of the fault
code.
Malfunction
Possible cause
Remedy
Water tap is blocked with limescale Check the water tap and have it re-
or faulty.
paired if necessary.
The tap is turned off.
Turn the tap on.
The filter (where present) in the
threaded hose fitting on the tap is
blocked.
Clean the filter in the threaded hose
fitting.
The cycle indicator for the select-
ed dishwashing cycle is flashing:
the control indicator Water is lit,
fault code Å10 is displayed in the
multi-display
Cancel the dishwashing cycle (see
chapter: Starting a dishwashing cy-
cle),
clean filters (see chapter: Cleaning
the filters),
Filters in the base of the washing
compartment are blocked.
(Problems with water inlet).
then start the dishwashing cycle
again.
Water inflow hose
has not been correctly positioned.
Check the position of the hose.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Malfunction
Possible cause
Remedy
The cycle indicator for the select- The sink outlet is blocked.
ed dishwashing cycle is flashing,
Clean out sink outlet.
fault code Å20 is displayed in the
Water drain hose
multi-display
(there is water in the dishwasher’s
Check the position of the hose.
has not been correctly positioned.
internal dispenser).
First shut off the water tap, then
switch off the appliance and contact
the Service Force.
Fault code Å30 is displayed in
the multi-display.
The anti-flood system has been
triggered.
The control indicator Door is lit.
The door of the dishwasher is open. Close the dishwasher door.
The indicator Filter is there to re-
mind you to check the dishwasher’s
The indicator goes out automatically
filters occasionally and to clean
at the start of the next dishwashing
them, if necessary. It lights up at
cycle.
The control indicator Filter is lit.
regular intervals, regardless of how
clean the filters are.
The mains plug is not
Plug in the mains plug.
plugged in.
A fuse in the house’s wiring system
Replace the fuse.
The cycle is not starting.
is defective.
For dishwasher models with a delay
If the dishes are to be washed im-
start timer:
mediately, cancel the delay start.
A start time has been selected.
The dishwashing compartment is
made from rust-free stainless steel.
Rust spots in the dishwashing com-
partment are due to rust particles
Only wash cutlery, dishes and pans
from external sources (rust particles
that are suitable for dishwasher use.
from water pipes, pans, cutlery,
Rust spots are visible in the dish-
washing compartment.
etc.). Remove such spots with a
commercially-available cleaning
product for stainless steel.
Decalcify appliance with commer-
cially available agents for cleaning
dishwashers.
The whistling is not a cause for
If the noises can still be heard after
concern.
A whistling noise can be heard
when washing dishes.
decalcifying the machine, use a dif-
ferent brand of detergent for wash-
ing cutlery and dishes.
The mains plug is not
Plug in mains plug.
plugged in.
The dishwasher interior light does
not come on.
The bulb in the interior light is faulty. Contact the Service Force.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
If the dishwashing results
are not satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the
dishwashing water did not reach all items. The
baskets for the dishes must not be overloaded.
The spray arms must be free to turn.
• Filters in the floor of the dishwasher are not clean
or incorrectly inserted.
• Good quality detergent was not used, or too little
was used.
• In the case of scale deposits on the dishes: The
special salt dispenser is empty or the water soften-
ing system has been incorrectly set.
• The drain hose is incorrectly positioned.
• If at the end of the dishwashing cycle there is still
detergent left in the detergent dispenser, either the
spray arm was jammed or the spray arm jets are
blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms
from their fixture for cleaning (see section “Care
and Cleaning”).
The dishes do not dry and are not shin-
ing.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or
a shiny bluish coating on glasses and
dishes.
• Lower rinse aid dosage.
There are dried water drops on the glass-
es and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the de-
tergent manufacturer's customer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer
advice centre.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal
2
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic com-
ponents are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at your
local waste disposal facilities.
2
Old appliance
The symbol
W
on the product or on its pack-
aging indicates that this product may not be
treated as household waste. Instead it shall be
handed over to the applicable collection point
for the recycling of electrical and electronic
equipment. By ensuring this product is dis-
posed of correctly, you will help prevent po-
tential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed in-
formation about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
1
Warning! When your appliance has finished
its working life, remove the plug from the
socket. Cut off the cable and plug and dispose
of them.
Break the door lock so that the door no longer
shuts. This prevents children from trapping
themselves inside and endangering their lives.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Capacity:
12 place settings including serving dishes
2
Permitted water pressure:
Electrical connection:
1-10 bar (=10-100 N/cm = 0.1-1.0 MPa)
AC 220 - 240 V, 50 Hz, 10 A; also see the rating plate on the right-hand side
of the dishwasher’s interior door .
Total output
2100 - 2300 W
Dishwasher: Free-standing appliances
Dimensions:
Max. weight:
850 x 598 x 598 (H x W x D in mm)
54 kg
5
This appliance conforms with the following EU
Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Direc-
tive
– 89/336/EEC dated 03.05.1989 EMC Directive in-
clusive of Amending Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes for Test Institutes
Testing in accordance with EN 60704 must be car-
ried out with the appliance fully loaded and using the
test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be car-
ried out when the salt dispenser in the water softener
and the rinse aid dispenser have been filled with salt
and rinse aid respectively, and using the test cycle
(see “Cycle Table”).
Full load:
Half load:
12 place settings
including serving dishes
6 place settings including serving dish-
es, leaving alternate positions in the
rack free
Amount of detergent required:
Rinse aid setting:
5g + 25g (Type B)
4 (Type III)
20g (Type B)
4 (Type III)
Sample loading arrangements:
*)
Upper basket
*) If necessary, you can remove the cup racks on the left-hand side.
*)
Lower basket with cutlery basket
Cutlery basket
*) If necessary, you can remove the cup racks on the left-hand side and/or the beer glass holder.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection instructions
1 Safety Information for the Installation
• Only transport the dishwasher in an upright posi-
tion, otherwise salt water may run out.
• Before using the dishwasher for the first time,
check for any damage caused in transport. Do not
under any circumstances connect an appliance
that is damaged. In the case of damage, please
contact your supplier.
• Never use the dishwasher if the mains cable, water
inlet or drain hose are damaged; or if the control
panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly in-
stalled shockproof socket.
• Permanent connection: a permanent connection
must only be installed by a trained electrician.
• Prior to using the appliance for the first time, en-
sure that the rated voltage and type of supply on
the rating plate match that of the supply where the
appliance is to be installed. The fuse rating is also
to be found on the rating plate.
• Multi-way plugs / connectors and extension cables
must not be used. This could constitute a fire haz-
ard through overheating.
• The dishwasher’s cable must only be replaced by a
Service Force Engineer.
• A water inlet hose with safety valve must only be
replaced by a Service Force Engineer.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Dishwasher
• The dishwasher must be installed on a firm floor
and adjusted to ensure that it is stable and level in
all directions.
• To compensate for unevenness in the floor and to
match the height of the appliance to that of sur-
rounding units, extend the threaded feet using a
screwdriver.
• The drain hose, inlet hose and mains cable must
be laid so that they are able to move freely within
the plinth area, and so that they are not kinked or
crushed when the dishwasher is in position.
• The dishwasher must also be screwed tightly to
the work surface or to the adjoining units. This is
essential to ensure the dishwasher does not tip up.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Free-standing appliances
1
If the dishwasher is installed directly next to a
cooker, a heat-insulating, non-flammable pan-
el (laminated with aluminium foil on the side
next to the cooker) must be fitted flush with
the top edge of the work surface (depth 57.5
cm).
If the appliance is built-in under a kitchen work sur-
face, the worktop supplied with the dishwasher can
be removed in the following way:
1.Unscrew the screws from the elbows at the rear
(1).
2.Push the appliance’s worktop backwards about 1
cm (2).
3.Lift the worktop at the front (3) and remove it.
1
3
If the dishwasher is later used as a free-stand-
ing appliance, the work surface supplied with
it must be re-mounted.
The plinth on free-standing appliances is not
adjustable.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the dishwasher
Connecting to the water
supply
• The dishwasher can be connected to cold or hot
water supplies up to max. 60°C.
• The dishwasher must not be connected to open
hot water appliances or instantaneous water heat-
ers.
Permitted water pressure
Lowest permitted water pressure:
1 bar (=10 N/cm2 =100 kPa)
Consult your plumber if the water pressure is less than
1 bar.
If the water pressure is greater than 10 bar, a pressure
reduction valve must be used (available from your
dealer).
Highest permitted water pressure:
10 bar (=100 N/cm2 =1 MPa)
Connecting the inlet hose
1
The water inlet hose must not be kinked,
crushed or entangled when it is being con-
nected.
Connect the threaded hose fitting (ISO 228-1:2000)
on the water inlet hose to a tap with an external
thread (¾ inch). The inlet hose is fitted with either a
plastic or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make
sure that the tap is not dripping.)
3
So that access to the tap in the kitchen is not
restricted by the use of the dishwasher, we
recommend installing an additional tap, or fit-
ting a T-branch to the existing tap.
If you need a longer water inlet hose than that sup-
plied, the following VDE-approved complete hose
sets are to be used. These are available from your lo-
cal Service Force.
Water drainage
Drain hose
1
The drain hose must not be kinked, crushed or
entangled.
Connecting the drain hose:
– Maximum permitted height: 1 metre.
– Minimum required height: 40 cm above the bot-
tom edge of the appliance.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension hoses
• Extension hoses are available from your local Serv-
ice Force Centre. To ensure that the function of the
appliance is not impeded, the internal diameter of
extension hoses must be 19 mm.
• Extension hoses must not be laid more than a
maximum distance of 4 metres horizontally; the
maximum permitted height for the connection for
the drain hose is then 85 cm.
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all com-
monly available sink outlet types. The outer diame-
ter of the sink outlet connection must be at least
15 mm.
• The drain hose must be fixed to the sink outlet
connection using the hose clamp supplied.
Water drainage if the dishwasher is built-
in at high level
If the dishwasher is installed at a high level, and the
drain hose connection is less than 30 cm from the
lower edge of the appliance, adapter kit
ET 111099520 must be fitted by your local Service
Force Centre.
Water drainage into sink (only possible
with free-standing appliances)
If you wish to hang the drain hose over the edge of a
sink, use a detachable hose elbow. You can obtain
this from Service Force by referring to spare part
number ET 646 069 190.
1.Fit the elbow to the drain hose.
2.Secure the drain hose so that it cannot slide off the
edge of the sink.
Pass a piece of cord through the hose elbow and
fix it to the wall or the tap.
Anti-flood system
For protection from water damage, the dishwasher is
equipped with a anti-flood system.
In the event of a fault, the safety valve immediately
interrupts the supply of water to the appliance and
the drain pump is activated.
In this way water can neither escape nor overflow.
The remaining water in the appliance is automatically
pumped out.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Any electrical work required to install this appli-
ance should be carried out by a qualified electri-
cian or competent person.
1
WARNING
earthed.
-
This appliance must be
The manufacturer declines any responsibil-
ity should these safety measures not be ob-
served.
Before switching on make sure the electricity supply
voltage is the same as that indicated on the appli-
ance rating plate.
To isolate the dishwasher from the mains, remove
the mains plug.
Important: The plug must still be accessible after
the appliance has been installed.
Changing a fuse
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS 1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
Green & Yellow
The wires on the mains lead are coloured in accord-
ance with the following code.
Green and Yellow:
Blue:
Brown:
Earth
Neutral
Live
Blue
Brown
• The wire coloured green and yellow must be con-
nected to the terminal marked with the letter “E“ or
by the earth symbol E or coloured green and yel-
low.
Cord Clamp
• The wire coloured blue must be connected to the
terminal “N“ or coloured black.
• The wire coloured brown must be connected to the
terminal marked “L“ or coloured red.
• Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must
be secure over the outer sheath.
1
WARNING! A cut off plug inserted into a 13
amp socket is a serious safety (shock) haz-
ard. Ensure that, if it is necessary to cut off
the plug, it is disposed of safely and not re-
tained.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting systems
The water inlet hose, drain hose and the mains cable
must all be connected to the side of the dishwasher
as there is no space for them behind the appliance.
2 connection pieces 45° or straight,
outer ø 19 mm, length 30 mm
double valve
water-
drainage
water inlet
waterinlet
mains
cable
water-
drainage
mains socket
mains cable
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty conditions
• The guarantee relates to you and cannot be trans-
ferred to another user.
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is
proved to be defective by reason only of faulty work-
manship or materials, we will, at our option repair or
replace the same FREE OF ANY CHARGE for labour,
materials or carriage on condition that:
• The appliance has been correctly installed and
used only on the electricity supply stated on the
rating plate.
• The appliance has been used for normal domestic
purposes only, and in accordance with the manu-
facturer’s instructions.
• The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any per-
son not authorised by us.
• Your new home is within the European Community
(EC) or European Free Trade Area.
• The product is installed and used in accordance
with our instructions and is only used domestically,
i.e. a normal household.
• The product is installed taking into account regula-
tions in your new country.
Before you move please contact your nearest Cus-
tomer Care Centre, listed below, to give them details
of your new home. They will then ensure that the lo-
cal Service Organisation is aware of your move and
able to look after you and your appliances.
France
Germany Nürnberg
Italy
Sweden
UK
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
+39 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 8705 727 727
+44 (0)1 4090751
Pordernone
Stockholm
Luton
• All service work under this guarantee must be un-
dertaken by a Service Force Centre.
• Any appliance or defective part replaced shall be-
Ireland
Dublin
come the Company’s property.
• This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be
charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, im-
proper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
• Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
• Products of Zanussi Electrolux manufacture which
are NOT marketed by Zanussi Electrolux.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
• The guarantee starts from the date you first pur-
chased your product.
• The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of prod-
ucts.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
If the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact
Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to
the Service Force Centre covering your post code ar-
ea.
For the address of your local Service Force Centre
and further information about Service Force, please
visit the website at
Before calling out an engineer, please ensure you
have read the details under the heading „What to do
if...“
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance
(found on the rating plate)
5. The purchase date.
Please note that a valid purchase receipt or guaran-
tee documentation is required for in-guarantee serv-
ice calls.
Customer Care Department
For general enquiries concerning your Zanussi Elec-
trolux appliance, or for further information on Zanus-
si Electrolux products, please contact our Customer
Care Department by letter or telephone at the ad-
si.co.uk.
Customer Care Department
Major Appliances
Zanussi Electrolux
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 727727 (*)
(*) calls to this number may be recorded for training
purposes.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
822 612 650-00-070306-04
Subject to change without notice
The Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products
(such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
Download from Www.Somanuals.com. All Manuals Search And Download.
|