GB
User manual
Dishwasher
2
ZDT311
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not change the specifications or modify this prod-
uct. Risk of injury and damage to the appliance.
• Do not use the appliance:
Contact your local Service Force Centre.
• Do not drill into the sides of the appliance to prevent
damage to hydraulic and electrical components.
– if the mains cable or water hoses are damaged,
Warning! Carefully obey the instructions for
electrical and water connections.
– if the control panel, worktop or plinth area are dam-
aged, that you can get access to the inner side of
the appliance.
Control panel
1
2
3
4
A
B
C
5
D
E
1
2
3
4
5
On/off button
Programme selection buttons
Delay start button
Indicator lights
Function buttons
Indicator lights
The indicator light comes on when it is necessary to fill
the salt container. Refer to the chapter 'Use of dishwasher
salt'.
1)
The salt indicator light can stay on for some hours, but
it does not have an unwanted effect on the operation of
the appliance.
The indicator light shows the activation/deactivation of
the multitab function. Refer to the chapter 'Multitab func-
tion'.
Multi-tab
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicator lights
The indicator light comes on when the washing pro-
gramme is completed. Auxiliary functions:
• Level of the water softener.
• Activation/deactivation of the audible signals.
• Activation/deactivation of the rinse aid dispenser.
• An alarm if the appliance has a malfunction.
1) The indicator light is off while a washing programme operates.
Function buttons
Audible signals
Use the function buttons for these operations:
You can hear an audible signal:
• To set the water softener. Refer to the chapter 'Setting • At the end of the washing programme.
the water softener'.
• During the setting of the level of the water softener.
• To deactivate/activate the audible signals. Refer to the
section 'Audible signals'.
• To activate/deactivate the multitab function. Refer to
the chapter 'Multitab function'.
• When the appliance has a malfunction.
The activation of the audible signals is set at the factory.
Do these steps to deactivate the audible signals:
1. Switch on the appliance.
• To deactivate/activate the rinse aid dispenser when
multitab function is active. Refer to the chapter 'Mul-
titab function'.
• To cancel the washing programme in progress or a
delay start in progress. Refer to the chapter 'Setting
and starting a washing programme'.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C until the
indicator lights of function buttons A, B and C start
to flash.
4. Press the function button C.
– Indicator lights for function buttons A and B go
off.
Delay start button
Use the delay start button to delay the start of the washing
programme with an interval of 3, 6 or 9 hours. Refer to
the chapter 'Setting and starting a washing programme'.
– Indicator light for function button C starts to flash.
– The end indicator light comes on.
The audible signals are activated.
Setting mode
5. Press the function button C again.
– The end indicator light goes off.
The audible signals are deactivated.
The appliance is in setting mode when all the programme
indicator lights are on.
The appliance must be in setting mode for these opera-
tions:
6. Switch off the appliance to save the operation.
Do these steps to activate the audible signals:
– To set a washing programme.
– To set the water softener level.
1. Do the above procedure until the end indicator light
comes on.
– To deactivate/activate the audible signals.
– To deactivate/activate the rinse aid dispenser.
If a programme indicator light is on, cancel the pro-
gramme to go back to the setting mode. Refer to the
chapter "Setting and starting a washing programme".
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Washing programmes
Programme
Degree of soil
Type of load
Programme description
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Heavy soil
Crockery, cutlery, pots
and pans
Drying
1)
Any
Crockery, cutlery, pots
and pans
Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying
2)
Normal or light soil Crockery and cutlery
Normal soil Crockery and cutlery
Main wash up to 65°C
Final rinse
3)
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Normal or light soil Delicate crockery and
glassware
Main wash up to 45°C
1 intermediate rinse
Final rinse
Drying
1) During the Auto programme, the soil level of the dishes is given by how cloudy the water is. The programme duration and
consumptions can change. This depends if the appliance is fully or not and on the level of soil on the dishes. The appliance adjusts
automatically the temperature of the water during the main wash.
2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load breakfast and
dinner crockery and cutlery.
3) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.
Consumption values
Programme
Duration (in minutes)
Energy (in kWh)
1,6-1,8
Water (in litres)
22-24
80-90
90-130
30
1,1-1,7
0,9
12-23
9
150-160
60-70
1,0-1,1
0,8-0,9
14-15
14-15
The pressure and temperature of the water, the var- iations of power supply and the quantity of dishes can
change these values.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of the appliance
Refer to the following instructions for each step of pro-
cedure:
5. Set the correct washing programme for the type of
load and soil.
1. Make a check if the water softener level is correct for 6. Fill the detergent dispenser with the correct quantity
the water hardness in your area. If necessary set the
water softener.
of detergent.
7. Start the washing programme.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dishwasher.
If you use detergent tablets, refer to the chapter 'Use
of detergent'.
Setting the water softener
The water softener removes minerals and salts from the
water supply. Minerals and salts can have bad effect on
the operation of the appliance.
Water hardness is measured in equivalent scales:
• German degrees (dH°).
• French degrees (°TH).
• mmol/l (millimol per litre - international unit for the
hardness of water).
• Clarke.
Adjust the water softener to the water hardness in your
area. If necessary, contact your local water authority.
Water hardness
Water hardness setting
°dH
°TH
91 - 125
76 - 90
65 - 75
51 - 64
40 - 50
33 - 39
26 - 32
19 - 25
7 - 18
mmol/l
9,1 - 12,5
7,6 - 9,0
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
3,3 - 3,9
2,6 - 3,2
1,9 - 2,5
0,7 - 1,8
< 0,7
Clarke
64 - 88
53 - 63
46 - 52
36 - 45
28 - 35
23 - 27
18 - 22
13 - 17
5 - 12
manually
electronically
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
19 - 22
15 - 18
11 - 14
4 - 10
2
2
2
2
2
2
1
1
1
10
9
8
7
6
5
4
3
2
1)
1)
< 4
< 7
< 5
1
1
1) No use of salt required.
You must set the water softener manually and elec-
tronically.
Manual adjustment
The appliance is set at the factory at position 2.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Release function buttons B and C.
5. Press function button A.
– The indicator light for function button A continues
to flash.
– The indicator lights for function buttons B and C
go off.
– The end indicator light starts to flash.
– You can hear an audible signal.
1
2
The setting function of the water softener is activated.
The end indicator light flashes and an audible signal
operates to show the level of the water softener. The
pause is approximately 3 seconds.
Example: 5 flashes / 5 intermittent audible signals -
pause - 5 flashes / 5 intermittent audible signals -
pause - etc... = level 5
Set switch to position 1 or
2.
Electronic adjustment
The water softener is set at the factory at level 5.
1. Switch on the appliance.
6. Press the function button A one time to increase the
water softener level by one step.
7. Press the on/off button to save the operation.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C until the
indicator lights for function buttons A, B and C start
to flash.
Use of dishwasher salt
Caution! Only use dishwashers salt. Types of salt
that are not applicable for dishwashers cause
damage to the water softener.
5
6
It is normal that water overflows from the salt con-
tainer when you fill it with salt.
1
3
2
4
Make sure that there is no grain of salt outer of the
salt compartment. Salt which stays on the tank for
a while drills the tank. It is recommended to start a wash-
ing programme immediately after you fill the salt con-
tainer. This prevents of corrosion because of spilled salt.
When you set electronically the water softener to level 1,
the salt indicator light does not stay on.
Fill the salt container with
1 litre of water (only the
first operation).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of rinse aid
Caution! Only use branded rinse aid for
dishwashers.
Fill when the rinse aid in-
dicator (B) becomes clear.
Do these steps to fill the rinse aid dispenser:
5
Caution! Do not fill the rinse aid dispenser with
other products (e.g. dishwasher cleaning agent,
liquid detergent). There is a risk of damage to the
appliance.
1
3
2
4
Adjusting the dosage of rinse aid
The rinse aid dial is set at
the factory at position 4.
To increase or decrease
the dosage refer to 'What
to do if...'
Loading cutlery and dishes
– Make sure that cutlery and dishes do notcover other
cutlery and dishes.
– Make sure that glasses do not touch other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can
keep water droplets. Plastic items do not dry as well
as porcelain and steel items.
• Put light items in the upper basket. Make sure that the
items do not move.
Helpful hints and tips
Caution! Only use the appliance for household
utensils that are applicable for dishwashers.
Do not use the appliance to clean objects that can absorb
water (sponges, household cloths, etc.).
• Before you load cutlery and dishes, do these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
• While you load cutlery and dishes, do these steps:
– Load hollow items (e.g. cups, glasses and pans)
with the opening down.
– Make sure that water does not collect in the con-
tainer or in a deep base.
– Make sure that cutlery and dishes do not lie inside
one another.
Caution! Make sure that the spray arms can move
freely before you start a washing programme.
Warning! Always close the door after you load or
unload the appliance. An open door can be
dangerous.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Put long-bladed knives
and long or sharp items in
the knife basket. The knife
basket is in the rear part of
the upper basket and, if
necessary, can be re-
moved.
Arrange service dishes
and large lids around the
edge of the lower basket.
3
The rows of prongs in the
lower basket can be flat to
loadpots, pans andbowls.
1
2
Arrange the items to let
water touch all surfaces.
For longer items fold the
cup racks up.
Prevent to put plates in the first three sections in the
front part of the upper basket. Make sure the plates
tilt forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first move the
upper basket to a upper position.
1
2
Warning! Adjust the height before you load the
upper basket.
Use the cutlery grid. If the dimensions of the cutlery
prevent use of the cutlery grid, remove it.
Maximum height of the dishes in :
upper basket
20 cm
lower basket
31 cm
Upper position
Lower position
24 cm
27 cm
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Do these steps to move the upper basket to the upper or
lower position:
1. Move the front runner stops (A) out.
2. Pull the basket out.
3. Put the basket in the upper or lower position.
4. Replace the front runner stops (A) in their initial po-
sition.
Caution! If the basket is in the upper position, do
not put cups on the cup racks.
1
2
Use of detergent
Only use detergents (powder, liquid or tablet) that
are applicable for dishwashers.
Follow the data on the packaging:
• Dosage recommended by the manufacturer.
• Storage recommendations.
Do not use more than the correct quantity of deter-
gent to save an environment.
5
6
Different brands of detergent dissolve in different
times. Some detergent tablets do not have the best
cleaning results during short washing programmes. Use
long washing programmes when you use detergent tab-
lets to fully remove the detergent.
1
3
2
4
Fill the detergent dispens- If you use a washing pro-
er (A) with detergent.
gramme with prewash
phase, put more detergent
in the prewash detergent
compartment (B).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Multitab function
The multitab function is for combi detergent tablets.
These tablets contain agents such as detergent, rinse aid
and dishwasher salt. Some types of tablets can contain
other agents.
Doacheckifthesetabletsareapplicableforthelocalwater
hardness. Refer to the instructions from the manufacturer.
When you set the multitab function, it stays on until you
deactivate it.
The multitab function stops automatically the flow of rinse
aid and salt. The rinse aid indicator light and salt indicator
light are deactivated.
The programme duration can increase if you use the mul-
titab function.
• You can only activate or deactivate the rinse aid dis-
penser when the multitab function is activated.
To activate the rinse aid dispenser:
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C.
– The indicator lights for function buttons A, B, and
C start to flash.
4. Press function button B.
– The indicator lights for function buttons A and C
go off.
– The indicator light for function button B continues
to flash.
5. Press function button B again.
– The end indicator light comes on.
6. Switch off the appliance to save the operation.
To deactivate the rinse aid dispenser do the above steps
until the end indicator light goes off.
Activate or deactivate the multitab function before
the start of a washing programme.
You cannot activate or deactivate the multitab function
when the programme operates. Cancel the washing pro-
gramme, then set the programme again.
To activate the multitab function:
• Press and hold the two multitab buttons (function but-
tons D and E). The multitab indicator light comes on.
To deactivate the multitab function:
To use normal detergent again:
1. Deactivate the multitab function.
• Press and hold the two multitab buttons (function but- 2. Fill the salt container and rinse aid dispenser.
tons D and E). The multitab indicator light goes off.
3. Adjust the water hardness setting to the highest level.
4. Do a washing programme without dishes.
5. Adjustthewatersoftenertothewaterhardnessinyour
area.
Do these steps if the drying results are not satis-
factory:
1. Fill the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser.
6. Adjust the rinse aid dosage.
3. Set the rinse aid dosage to position 2.
Setting and starting a washing programme
Set the washing programme with the door ajar. The
washing programme only starts after you close the
door. Until then it is possible to modify the settings.
Whenthewashingprogrammeoperates,youcannot
change the programme. Cancel the washing pro-
gramme.
Do these steps to set and start a washing programme:
1. Switch on the appliance.
Warning! Only interrupt or cancel a washing
programme if necessary.
2. Make sure that the appliance is in setting mode.
3. Press one of the programme buttons. Refer to the
chapter 'Washing programmes'.
– The programme indicator light comes on.
4. Close the door.
Caution! Open the door carefully. Hot steam can
come free.
Cancelling a washing programme
1. Press and hold function buttons B and C until all the
programme lights come on.
– The washing programme starts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Release function buttons B and C to cancel the wash-
ing programme.
At this time you can do these steps:
vent interruption of the countdown. When you close the
door again, the countdown continues from the point of
interruption.
1. Switch off the appliance.
2. Set a new washing programme .
Fill the detergent dispenser with detergent before you set
a new washing programme.
Cancelling a delay start:
1. Press and hold function buttons B and C until all the
programme lights come on.
– When you cancel a delay start, you also cancel the
washing programme.
2. Set a new washing programme.
Interrupting a washing programme
Open the door.
• The programme stops.
Close the door.
• The programme continues from the point of interrup-
tion.
End of the washing programme
Switch off the appliance in these conditions:
• The appliance stops automatically.
• The audible signals for the end of the programme op-
erate.
1. Open the door.
– The end indicator light comes on.
– The programme indicator light stays on.
2. Press the on/off button.
3. For better drying results, keep the door ajar for some
minutes before you remove the dishes.
Setting and starting a washing programme with
delay start
1. Press the on/off button.
2. Set a washing programme.
– The programme indicator light comes on.
3. Press the delay start button until the indicator light
with the correct number of hours starts to flash (3, 6,
or 9 hours).
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.
4. Close the door.
– The countdown of the delay start starts.
– The countdown of the delay start decreases with
steps of 3 hours.
When the countdown is completed, the washing
programme starts automatically.
Removing the load
• First remove items from the lower basket, then from
the upper basket.
• There can be water on the sides and door of the appli-
ance. Stainless steel becomes cool more quickly than
the dishes.
Do not open the door during the countdown to pre-
Care and cleaning
Warning! Switch the appliance off before you clean
the filters.
Cleaning the filters
Important! Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.
Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.
1
2
Fully clean the filters A, B
and C below running wa-
ter.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
6
5
To remove filters B and C, Remove the flat filter A
turn the handle approxi- from the bottom of the ap-
mately 1/4 anticlockwise. pliance.
Put the filter system in po-
sition. To lock the filter
system, turn the handle
clockwise until it locks in
position.
Put the flat filter A in the
bottom of the appliance.
Install the flat filter cor-
rectly under the two
guides D.
Important! Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a cocktail stick.
External cleaning
Clean the external surfaces of the appliance and control
panel with a damp soft cloth. Only use neutral detergents.
Do not use abrasive products, scouring pads or solvents
(acetone, trichloroethylene etc...).
Frost precautions
Caution! Do not install the appliance where the
temperature is below 0 °C. The manufacturer is not
responsible for damage because of frost.
If not possible, empty the appliance and close the door.
Disconnect the water inlet hose and remove water from
the water inlet hose.
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem
yourself. If you cannot find a solution to the problem
yourself, contact the Service Force Centre.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault code and malfunction
Possible cause and solution
• continuous flash of the light of the run- • The water tap is blocked or furred with limescale.
ning programme
Clean the water tap.
• intermittent audible signal
• 1 flash of the end indicator light
• The water tap is closed.
Open the water tap.
The dishwasher does not fill with water
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the light of the run- • There is a blockage in the sink spigot.
ning programme
Clean the sink spigot.
• intermittent audible signal
• 2 flashes of the end indicator light
The dishwasher will not drain
• The connection of the water drain hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the light of the run- • Close the water tap and contact your local Service Force Centre.
ning programme
• intermittent audible signal
• 3 flashes of the end indicator light
The anti-flood device operates
The programme does not start
• The appliance door is not closed.
Close the door.
• Mains plug is not connected in.
Put in the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start is set.
Cancel the delay start to start the programme immediately.
After the check, switch on the appliance. The programme • Serial number (S.N.)
continues from the point of interruption. If the malfunction For these data, refer to the rating plate.
shows again, contact your Service Force Centre.
These data are necessary to help you quickly and cor-
rectly:
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
• Model (Mod.)
• Product number (PNC)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
The cleaning results are not satisfactory
The dishes are not clean
• The selected washing programme is not applicable for the type of load and
soil.
• The baskets are loaded incorrectly so that water cannot reach all surfaces.
• Spray arms do not turn freely because of incorrect arrangement of the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
Limescalesparticlesonthedishes • The salt container is empty.
• The water softener is adjusted on a wrong level.
• The salt container cap is not closed correctly.
The dishes are wet and dull
• No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or • Decrease the rinse aid dosage.
a bluish coating on glasses and
dishes
Dry water drop signs on glasses • Increase rinse aid dosage.
and dishes
• The detergent can be the cause.
Technical data
Dimensions
Width cm
Height cm
Depth cm
59,6
81,8-87,8
55,5
Electrical connection - Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressure
Minimum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
12
Maximum
Capacity
Place settings
Environment concerns
information about recycling of this product, please
contactyourlocalcouncil,yourhouseholdwastedisposal
service or the shop where you purchased the product.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
The packaging materials are environmentally friendly and
can be recycled. The plastic components are identified by
markings, e.g. >PE<, >PS<, etc. Discard the packaging
materials in the applicable container at the community
waste disposal facilities.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning! To discard the appliance, follow the
procedure:
• Pull the mains plug out of the socket.
• Discard the door catch. This prevents the children to
close themselves inside the appliance and endanger
their lives.
• Cut off the mains cable and mains plug and discard
them.
Installation
The dishwasher has adjustable feet to allow the adjust-
ment of the height.
Make sure that the water inlet hose, the drain hose and
the supply cable are not kinked or squashed, when you
insert the machine.
Warning! Make sure that mains plug is
disconnected from the mains socket during
installation.
Important! Obey the instructions in the enclosed template
to:
• Build-in the appliance.
• Install the furniture panel.
• Connect to the water supply and drain.
Attaching the appliance to the adjacent units
Make sure that the counter below which you attach the
appliance is a safe structure (adjacent kitchen units, cab-
inets, wall).
Install the appliance under a counter (kitchen worktop or
sink).
If a repair is necessary, the appliance must be easily ac-
cessible for the engineer.
Put the appliance adjacent to a water tap and a drain.
For the venting of the dishwasher only water fill, water
drain and power supply cable openings are necessary.
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal the
door correctly. If the level of the appliance is correct, the
door does not catch on the sides of the cabinet. If the door
does not close correctly, loosen or tighten the adjustable
feet until the appliance is level.
Water connection
Water inlet hose
Connected the appliance to a hot (max. 60°) or cold water
supply.
Caution! Do not connect the appliance to new pipes
or pipes that are not used for a long time. Let the
water run for some minutes, then connect the inlet hose.
If the hot water comes from alternative sources of energy
that are more environmentally friendly (e.g. solar or pho-
tovoltaic panels and aeolian), use a hot water supply to
decrease energy consumption.
Connect the inlet hose to a water tap with an external
thread of 3/4”.
Water inlet hose with safety valve
The water inlet hose is a double-walled and has an inner
mains cable and a safety valve. The water inlet hose is
under pressure only while the water is running. If there is
a leak in the water inlet hose, the safety valve interrupts
the running water.
Caution! Do not use connection hoses from an old
appliance.
Warning! Danger-
ous voltage
The water pressure must be in the limits (refer to the
chapter 'Technical data'). Make sure that the local water
authority gives you the average mains pressure in your
area.
Make sure that there are no kinks in the water inlet hose
and that the water inlet hose is not squashed or entangled.
Turn the inlet hose to the left or the right to suit the in-
stallation. Fit the locknut correctly to prevent water leaks.
Be careful when you connect the water inlet hose:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not put the water inlet hose or the safety valve in
water.
• If the water inlet hose or the safety valve is damaged,
immediately disconnect the mains plug from the mains
socket.
• Only let the Service Force Centre replace the water inlet
hose with safety valve.
Drain hose
max 85 cm
min 40 cm
3
4
The internal diameter must not be smaller than the diam-
eter of the hose.
If you connect the water drain hose to a trap spigot under
the sink, remove the plastic membrane (A). If you do not
removethe membrane, remainingfoodcan cause ablock-
age in the drain hose spigot.
Caution! Make sure that the water couplings are
tight to prevent water leakage.
1
2
Connect the water drain
hose to the sink spigot.
Electrical connection
Warning! The manufacturer is not responsible if
you do not follow these safety precautions.
Ground the appliance according to safety precautions.
Do not replace the mains cable yourself. Contact the
Service Force Centre.
Make sure that the mains plug is accessible after
Make sure that the rated voltage and type of power on the installation.
rating plate agree with the voltage and the power of the
local power supply.
Do not pull the mains cable to disconnect the appliance.
Always pull the mains plug.
Always use a correctly installed shockproof socket.
Do not use multi-way plugs, connectors and extension
cables. There is a risk of fire.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|