GAS HOB
ZGL 62 ITX
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
IE
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the Installer
Instructions for the Installer
For the User
8
10
12
13
13
15
15
Important Safety Information
Description of the Hob
Operation
2
4
Installation
Electrical connections
Wiring Diagram
5
Maintenance and Cleaning
Something Not Working?
Service and Spare Parts
Guarantee/Customer Service
European guarantee
6
Fault Finding
7
Commissioning
7
Conversion from Natural Gas to LPG
16
17
Environmental Information
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
z
After installation, please dispose of the packaging
with due regard to safety and the environment.
z
When disposing of an old appliance, make it unusable,
by cutting off the cable.
Safety Instructions
z
The symbol
on the product or on its packaging
Step by step instructions for an operation
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
)
Hints and Tips
Environmental Information
This appliance complies with the following
E.E.C. Directives:
73/23 - 90/683
(Low VoltageDirective);
*
*
*
*
93/68 (General Directives);
89/336 (Electromagnetical Compatibility Directive);
90/396 (GasAppliances),
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
and subsequent modifications
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the Hob
3
4
3
1
2
5
6
1. HobTop
2. Auxiliary Burner
3. Semi-rapid Burners
4. Rapid Burner
5. Control knobs
6. Electric Ignition Push Button
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Hob burners
To light a burner:
)
z
z
pushtheelectricignitionpushbuttonwhichismarked
by a little spark.
at the same time turn the relevant control knob
anticlockwisetomaximumpositionandkeepitpushed
down about 5 seconds.
This will allow the "thermocouple" (see diagram -
letter D) to be heated and the safety device to be
switched off, otherwise the gas supply would be
interrupted.
z
then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several attempts,
check the "cap" and “crown” (see diagram - letterA and
B) are in the correct position.
To put the flame out, turn the knob to the symbol z.
When switching on the mains, after
installation or a power cut, it is quite normal
for the spark generator to be activated
automatically.
A - Burner cap
B - Burner crown
C - Ignition electrode
D - Thermocouple
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
minimum
diameter
maximum
diameter
Large(rapid)
Medium(semi-rapid)
Small(auxiliary)
180 mm
120 mm
80 mm
260 mm
220 mm
160 mm
If you use a saucepan which is smaller than
the recommended size, the flame will spread
beyond the bottom of the vessel, causing the
handle to overheat.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid simmering.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Before any maintenance or cleaning can be
carried out, you must DISCONNECT the hob
from the electricity supply.
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little washing up
liquid has been added.Avoid the use of the following:
-
-
household detergent and bleaches;
impregnated pads unsuitable for non-stick
saucepans;
-
-
steel wool pads;
bath/sink stain removers.
Should the hob top become heavily soiled, the following
productsarerecommended:
- For stainless steel hobs use a proprietary stainless
steel cleaner.
- For other hobs use Hob Brite or Bar Keepers Friend.
Pan Supports
Thepansupportsaredishwasherproof.Ifwashingthem
by hand, take care when drying them as the enamelling
process occasionally leaves rough edges. If necessay,
remove stubborn stains using a paste cleaner.
The Burners
Theburnercapsandcrownscanberemovedforcleaning.
Washtheburnercapsandcrownsusinghotsoapywater,
and remove marks with a mild paste cleaner. A well
moistenedsoapimpregnatedsteelwoolpadcanbeused
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
Ignition electrode
The electric ignition is obtained through a ceramic
"electrode" and a metal electrode (see diagram on page
4 - letter C). Keep these components very clean, to avoid
lighting difficulties, and check that the burner crown
holes are not obstructed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service
Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
SYMPTOM
SOLUTION
„ There is no spark when lighting the gas
‹ Check that the unit is plugged in and the electrical
supply is switched on
‹ Check that the RCCB has not tripped (if fitted)
‹ Check the mains fuse has not blown
‹ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
„ The gas ring burns unevenly
‹ Check the main jet is not blocked and the burner
crown is clear of food particles.
‹ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for the Installer
Engineers technical data
Overall dimensions
Rear Left Burner
Heat Input
(semi rapid)
2.0 kW (6824 BTU/HR)
Width:
Depth:
580 mm
500 mm
Front Left Burner
Heat Input
(auxiliary)
1.0 kW (3412 BTU/HR)
Cut out dimensions
Rear Right Burner
Heat Input
(semi rapid)
2.0 kW (6824 BTU/HR)
Width:
Depth:
550 mm
470 mm
Front Right Burner
Heat Input
(rapid)
3.0 kW (10236 BTU/HR)
Supply connections
Gas:
RC 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
230 V 50 Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
BURNER
RAPID
(large)
SEMI-RAPID
(medium)
AUXILIARY
(small)
POSITION
MAX
MIN
MAX
MIN
MAX
MIN
NOMINALTHERMAL
POWER
kW
3.0
0.65
2.0
0.45
1.0
0.095
70
0.33
0.031
Adjust.
NOMINALFLOW
RATE
m3/h 0.286 0.062 0.190 0.043
NOZZLEREFERENCE
1/100mm
119 Adjust.
96
Adjust.
NOMINALTHERMAL
POWER
kW
2.8
0.65
2.0
0.45
1.0
0.33
NOMINALFLOW
RATE
g/h
202
86
47
40
144
71
32
32
72
50
24
28
NOZZLEREFERENCE
1/100mm
Burner
Dia. Tap By-pass
APPLIANCE CLASS:
3
1/100 mm
APPLIANCE CATEGORY:
II2H3+
Auxiliary
Semi-rapid
Rapid
28
32
40
APPLIANCE GAS SUPPLY:Natural gas G20/20 mbar
Aerationadjustmentnone
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety requirements
This hob must be installed in accordance with the Gas
Safety (Installation and Use) Regulations (Current Edition)
and the IEE Wiring Regulations (Current Edition).
Location
The hob may be located in a kitchen, a kitchen/diner or
bed sitting room, but not in a bathroom, shower room or
garage.
Before making the cut out in the worktop ensure that
there is a minimum distance of 55 mm between the rear
edge of the hob and the wall.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S. 813 Current
Editions and the ETCI Rules for Electrical Installations.
Provision for ventilation
A minimum distance of 100 mm must be left between
the side edges of the hob and any adjacent cabinets or
walls.
The minimum distance combustible material can be fitted
above the hob in line with the edges of the hob is 400
mm. If it is fitted below 400 mm a space of 50 mm must
be allowed from the edges of the hob.
Detailed recommendations are contained in the following
British Standards Codes Of Practice: B.S. 6172/ B.S.
5440, Part 2 and B.S. 6891 Current Editions.
The hob should not be installed in a bed sitting room
with a volume of less than 20 m3. If it is installed in a
room of volume less than 5 m3 an air vent of effective
area of 110 cm2 is required. If it is installed in a room of
volume between 5 m3 and 10 m3 an air vent of effective
area of 50 cm2 is required, while if the volume exceeds
11 m3 no air vent is required.
The minimum distance combustible material can be fitted
directly above the hob is 700 mm.
For appliances installed in the Republic of Ireland please
refer to NSAI- Domestic Gas Installation I.S 813 Current
Edition Section 7- Permitted Locations of Appliance.
However, if the room has a door which opens directly to
the outside no air vent is required even if the volume is
between 5 m3 and 11 m3.
If there are other fuel burning appliances in the same
room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent
requirements.
For appliances installed in the Republic of Ireland please
refer to the NSAI- Domestic Gas Installation I.S. 813
Current Editions Table Four.
ICLEARANCESREQUIRED
WHEN FITTING THE HOB
WITHOUTACOOKERHOODABOVE
CLEARANCESREQUIRED
WHEN FITTING THE HOB
WITHACOOKERHOODABOVE
600 mm
700 mm
7
0
0m
m
400 mm
400 mm
50 mm
55 mm
50 mm
55 mm
400 mm
400 mm
100 mm
100 mm
50 mm
50 mm
FO 0812
FO 0813
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
IMPORTANT: This hob must be installed by a
competent person to the relevant Gas Standards.
Please, ensure that, once the hob is installed, it
is easily accessible for the engineer in the event
of a breakdown.
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important to
remove any protective materials, which were put
on in the factory.
Any gas installation must be carried out by a
competent person.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this book be ignored.
On the end of the shaft, which includes the GJ 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using
excessive force.
Gas Connection
Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to RC
1/2 (1/2 BSP male thread).
FO 0264
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation.
Ensure that the main connection pipe does not exert
any strain on the hob.
A) End of shaft with nut
B) Washer
C) Elbow
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.
Rectangular cut-out size for hob
Cut Out Size
The dimensions of the cut-out are given in the diagram.
Dimensions are given in mm.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Building In
Building over a cupboard or
drawer
If the hob is to be installed above a cupboard or drawer it
will be necessary to fit a heat resistant board below the
base of the hob on the underside of the work surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
2
1
3
ON/OFF SWITCH
ON/OFF SWITCH
FLEX
OUTLET
FLEX
OUTLET
FO 1013
FO 0763
FO 0764
Dimensions are given in mm.
Building over a kitchen unit with
door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the bottom
of the hob which can be heated when it is operated. The
recommended solution is shown in diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical assistance
is needed. The space behind the kitchen unit ("b") can
be used for connections.
Fitting the Hob into the worktop
Carry out the building in of the hob as follows:
)
•
put the seals supplied with the hob, on the
edges of the cut out taking care that the seals
meet without overlapping;
•
•
place the hob in the cut out, taking care that it
is centred;
fix the hob with the relevant fixing clamps and
screws, as shown in the diagram. When the
screws have been tightened, the excess seal
can be removed.
Seal
a
The edge of the hob forms a double seal which prevents
the ingress of liquids.
FO 0199
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connections
Any electrical work required to install this hob
Permanent Connection
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
THIS HOB MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
The switch must not break the yellow and green earth
cable at any point.
This hob is designed to be connected to a 230 V 50 Hz
AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
Ensure that the hob supply cable does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
The hob is supplied with a 3 core flexible supply cable
incorporating a 3amp plug fitted. In the event of having to
change the fuse, a 3ampASTAapproved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
- Neutral
- Live
Blue
Brown
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
)
the letter 'E' or the earth symbol
green and yellow.
or coloured
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cable clamp must be secure over
the outer sheath.
FO 0390
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that
the cut off plug is disposed of safely.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
A. TAPS IGNITOR SWITCHES
B. IGNITOR UNIT
Fault Finding
Preliminary Electrical Systems Check
SOCKET
PLUG (with cover removed)
Earth Wire
Green/Yellow
(face view)
( )
( )
E
Brown
Blue
START
Neutral Wire
Blue
Isolate appliance
and carry out:
A: Earth Continuity
check.
N
L
Blue
Green
Yellow
Brown
Carry out:
D: Resistance to
Earth check.
Electricity supply
should now be
satisfactory.
YES
NO
Carry out:
C: Polarity check.
A. EARTH CONTINUITY CHECK - Appliance must
be electrically disconnected - meter set on Ω (Ohms)
x 1 scale and adjust zero if necessary.
Has inlet fuse blown?
a) Test leads from any appliance earth point to earth
pin on plug. Resistance should be less than 0.1 Ω
(Ohm), check all earth wires for continuity and all
contacts are clean and tight.
YES
NO
B. INSULATION CHECK - Appliance electrically
disconnected, all switches ON.
Inlet wiring
faulty.
Rectify any
fault.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from Lto N in appliance terminal block.
If meter reads «0» then there is a short circuit.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than ∞ (infinity) there is a fault.
NOTE - Should it be found that the fuse has failed but
no fault is indicated - a detailed continuity check (i.e.
by disconnecting and checking each component) is
required to trace the faulty component.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
It is possible that a fault could occur as a result of
local burning/arcing but no fault could be found under
test. However a detailed visual inspection should reveal
evidence of burning around the fault.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Ignition System / Gas Ignition
YES
Check gas supply at
burner
Ignitor does not spark
NO
Check plug top fuse
and
replace if necessary
Light burner manually
Check by pass
simmer
Check polarity and
earth continuity of
supply point
Check position of the
electrode
Check earth continuity
of appliance
Check continuity from the tip
of each electrode to the
terminals 1 to 4 on the ignitor
unit
Check fitting of burners
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check for breaks in the
insulation
of the HT leads
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check continuity from ignition
switches connector to ignitor unit
Change the taps
ignition switches
Change the ignitor unit
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
-
Turn the gas tap to the MAX position and ignite.
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
)
-
-
Re-ignite the burner and set to MIN.
Remove the control knob and use a thin bladed
screwdriver to turn the adjustment screw until the
flame is steady and does not extinguish, when the
knob is turned from MIN to MAX.
-
-
The adjustment screw may be located at the centre
of the gas tap control shaft or on the gas tap body,
left of the control shaft or below (see diagram).
Repeat the adjustment procedure for all burners.
Pressure Testing
)
-
Remove left hand pan support and front left burner
cap and crown.
Adjustment
screw
-
-
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another
burner.
-
-
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
Conversion from Natural Gas to LPG
IMPORTANT
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, which is
located down the centre of the gas tap control shaft.
The replacement/conversion of the gas hob should only
be undertaken by a competent person.
It is important to note that this model is designed for use
Upon completion stick the replacement rating plate on
with natural gas but can be converted for use with butane
the under side of the hob.
or propane gas providing the correct injectors are fitted
and the gas rate is adjusted to suit.
Method
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the hob from the electrical supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
•
With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee/Customer Service
Standard guarantee conditions
We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance
or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
· The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
· The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s instruc-
tions.
· The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not author-
ised by us.
· Electrolux Service Force Centre must undertake all service work under this guarantee.
· Any appliance or defective part replaced shall become the Company’s property.
· This guarantee is in addition to your statutory and other legal rights.
Exclusions
· Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or remov-
able parts of glass or plastic.
· Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom.
· Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements.
· Products of Electrolux manufacturer that are not marketed by Electrolux.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre covering your postcode area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at
Before calling out an engineer, please ensure you have read the details under the heading “Something not working”
When you contact the Service Force Centre you will need to give the following details:
1.Your name, address and postcode.
2.Your telephone number.
3. Clear concise details of the fault.
4. The model and Serial number of the appliance (found on the rating plate).
5.The purchase date.
Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls.
Customer Care
For general enquiries concerning your Electrolux appliance, or for further information on Electrolux products please
contact our Customer Care Department by letter or telephone at the address below or visit our website at
Customer Care Department
Electrolux MajorAppliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 727 727 (*)
(*) Calls may be recorded for training purposes
16
Download from Www.Somanuals.com. All Manuals Search And Download.
European guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period
specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries
listed below the appliance guarantee will move with you subject to the following qualifications:
•
•
The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of
a valid purchase document issued by the seller of the appliance.
The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new country
of residence for this particular model or range of appliances.
•
•
The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user.
The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home,
i.e. is not used for commercial purposes.
•
The appliance is installed in accordance with all relevant regulations in force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
35687-8002
11/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|