ZALMAN Computer Hardware GV1000 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Exploded View  
VGA Cooler  
RAM Heatsink  
Nipple  
Rubber Ring  
VGA RAM  
VGA Chipset  
PVC Washer  
Spring  
Fixing Nut  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The specifications of any product may change without prior notice to improve performance.  
2
Installation Procedure  
The following installation sequence MUST be followed.  
(1. VGA RAM Heatsink Attachment 2. Thermal Grease Application 3. Nipple Installation on Retention Guide →  
4. VGA Cooler Installation 5. Spring Insertion on the Fixing Nut 6. Fixing Nut Assembly on VGA Coolers  
Nipple 7. VGA Card Installation 8. Fan Power Cable Connection)  
1. VGA RAM Heatsink Attachment  
Remove the film from the Thermal Tapes on the bottom of the  
RAM Heatsinks and attach the Heatsinks on the VGA RAM.  
RAM  
Note 1) If Thermal Grease or other residue remains on the  
Heatsink  
RAM, then the Thermal Tapes will not stick. Clean the  
surface of the RAM with acetone or alcohol before  
attaching the RAM Heatsinks.  
Note 2) The bonding strength of the Thermal Tapes reaches  
VGA  
RAM  
90% after 24 hours of curing. Do not exert excessive  
force on the RAM Heatsinks during this period.  
Note 3) Thermal Tapes are not reusable because they lose  
adhesiveness after their initial application. Purchase  
new Thermal Tapes if the RAM Heatsinks need to be  
reattached.  
Thermal Tape  
2. Thermal Grease Application  
Film  
Clean the contact surface of the VGA Chipset completely.  
Apply Thermal Grease on the VGA Chipset that makes  
contact with the base of the VGA Cooler.  
Thermal  
Grease  
3. Nipple Installation on the Retention Guide  
Install the short end of the Nipples on the VGA Coolers  
Retention Guide after determining the appropriate Installation  
Holes.  
(Note) The Nipples MUST be tightened by hand. Using tools to  
tighten the Nipples may damage the tips of the Nipples.  
Please check the table below to identify the correct Nipple  
Installation Holes for specific models of VGA cards.  
VGA  
Chipset  
Nipple Installation Holes for  
Various VGA Cards  
Nipple Installation Holes  
VGA Card  
Nipple  
ATI X1600 Series  
ATI X1300 Series  
ATI Radeon 9 Series (except 9550/9600)  
***  
ATI Radeon X Series  
***  
NVIDIA Geforce4 MX Series  
NVIDIA Geforce FX 5200  
NVIDIA Geforce FX 5500  
NVIDIA Geforce FX 5600 (FX 5700)  
NVIDIA Geforce 6600 Series (except 6600 AGP Series)  
NVIDIA Geforce4 TI 4 Series  
NVIDIA Geforce FX 5700(Ultra) Series  
NVIDIA Geforce FX 5800 Series  
NVIDIA Geforce 6600 Series (except 6600 AGP Series)  
ATI HD 2600 Series  
ATI HD 2400 Series  
ATI X1650 Series  
ATI X1600 Series  
NVIDIA Geforce 8600 Series  
NVIDIA Geforce 8500 Series  
NVIDIA Geforce 7600 Series  
NVIDIA Geforce 7300 Series  
NVIDIA Geforce 6600 Series (except 6600 AGP Series)  
NVIDIA Geforce FX 5900 Series  
NVIDIA Geforce FX 5950 Series  
NVIDIA Geforce 8800GT, 8800GTS (G92)  
ATI HD 3870, HD 3850  
Retention  
Guide  
VGA Cooler  
Nipple  
Installation  
Holes  
ATI X1950 Series, ATI X1900 Series  
ATI X1800 Series  
NVIDIA Geforce 7950 Series  
NVIDIA Geforce 7900 Series  
NVIDIA Geforce 7600 Series  
NVIDIA Geforce 7800 Series  
NVIDIA Geforce 6800 Series  
NVIDIA Geforce 8800 Series (G80)  
Retention Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The specifications of any product may change without prior notice to improve performance.  
3
4. VGA Cooler Installation  
Insert the Rubber Rings into the VGA Coolers Nipples.  
Install the Nipple-attached VGA Cooler on the VGA cards Mounting Holes.  
The VGA Chipset MUST be positioned on the center of the VGA Coolers base.  
Simultaneously hold the VGA Cooler and the VGA card with one hand, then flip the VGA card so that its rear-  
side is facing upwards.  
(Note)  
Make sure that the VGA Chipset and the VGA Coolers base do not get detached while simultaneously flipping  
the VGA Cooler and the VGA card.  
VGA Cooler  
Nipple  
Rubber Ring  
Nipple  
Rubber  
Ring  
Nipple  
VGA  
Cooler  
Spring  
5. Spring Insertion on the Fixing Nut  
Slowly turn the Spring in counter clockwise motion so that the  
Spring is correctly attached to the Fixing Nut.  
Note 1) The ends of the Springs are of different diameters.  
Install the Spring end with the smaller diameter on the  
Fixing Nut as shown in the diagram.  
Fixing Nut  
Fixing Nut  
Note 2) Make sure that the Spring is installed perpendicularly  
and not leaning to one side.  
PVC Washer  
6. Fixing Nut Installation on the Nipples  
Place a PVC Washer over each Nipple on the back side of  
the VGA card.  
Nipple  
Slightly screw each of the four Spring-attached Fixing Nuts  
onto each Nipple, then tighten each Fixing Nut one rotation  
at a time until all are completely tightened.  
Interference may occur between the Fixing Nuts of the two  
VGA coolers when using an SLI or CrossFire VGA card  
setup. In such a case, use the enclosed Fixing Nut for SLI  
/CrossFire for assembly.  
For SLI or CrossFire Installations  
Fixing Nut for  
SLI/CrossFire  
PVC Washer  
Note 1) Fully tightening one Fixing Nut at a time may result in  
damaging the VGA chipset. Please tighten each Fixing  
Nut one rotation at a time until all are completely  
tightened.  
Note 2) Make sure that the VGA Coolers base and the VGA  
Chipset are completely in contact with each other.  
Note 3) Make sure that the VGA Cooler does not interfere with  
the VGA cards capacitors and other components.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The specifications of any product may change without prior notice to improve performance.  
4
7. VGA Card Installation  
Insert the assembled VGA card into the motherboards PCIe (or AGP) slot. Use the Fixing Bolt to secure the  
VGA card onto the computer case. If the VGA card has a power connector on it, then remember to plug in the  
power cable.  
PCIe Slot  
Fixing Bolt  
8. Fan Power Cable Connection  
Installing FAN MATE 2 on the Inside of the System Installing FAN MATE 2 on the Outside of the System  
Double - Sided Tape  
RPM Control Knob  
Fan Connector  
(Z-Machine GV1000)  
FAN MATE 2  
6-Pin  
Connector  
Motherboard  
Connect the appropriate 3-pin connector on the  
cable to the motherboard fan header and the  
Z-Machine GV1000 fan connector.  
Pull the 6-pin connector out of the system through  
the back and connect it to FAN MATE 2, which  
should be installed on the case using the included  
Double-Sided tape ().  
When the RPM Control Knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Quite  
Mode. Turned fully clockwise, it operates in Performance Mode. You can select the desired fan RPM by  
turning the knob.  
Performance can be increased by adjusting the RPM control knob of the FAN MATE 2.  
Note) FAN MATE 2 has been specifically designed for the fan of this product.  
Zalman Tech Co., Ltd. is not responsible for any damage to systems or VGA Chipsets caused by  
using it with other types of fans.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The specifications of any product may change without prior notice to improve performance.  
5
Zalman Computer Noise Prevention Systems  
When building a noiseless computer, use Zalmans Ultra Quiet CPU Cooler, Noiseless Power Supply, Heatpipe  
HDD Cooler, Fanless Northbridge Cooler and Noiseless Case Fan for more stable performance and a noiseless  
environment.  
Noiseless Power Supply  
Heatpipe HDD Cooler  
Noiseless Case FAN  
Ultra Quiet CPU Cooler  
Fanless Northbridge Cooler  
Computer Enclosures  
High End Gaming Enclosure Built with  
Sturdy All Aluminum Panels  
Three Tool Free Hinged Magnetic Panels  
(2 Left, 1 Right) for Easy Installation and  
Access to Components  
Tool Free Installation of Disk Drives (HDD,  
ODD, FDD), Fan Controllers, Audio  
Interfaces etc.  
Accommodates up to 6 Hard Drives (4 in  
the HDD Chassis, 2 on the Bottom Panel)  
Luxurious and Cool Aesthetics  
Color Options : Black (Red LED Fans),  
Titanium (Blue LED Fans)  
GT-1000  
Home Theatre PC Enclosures  
The HD160XT is designed for ultra quiet home theatre  
PC operation, utilizing optimized ventilation and  
anti-vibration reinforcements, making it ideal for  
environments that require silence such as living  
rooms, bedrooms, educational facilities, and offices.  
For more information, please visit our website.  
HD160XT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The specifications of any product may change without prior notice to improve performance.  
6

West Bend Food Processor ESFP300 User Manual
Whirlpool Range W10394387A User Manual
Yamaha Cassette Player KX W321 User Manual
Yamaha Musical Instrument 2428440 User Manual
Zanussi Freezer ZCF 52 C User Manual
Zanussi Microwave Oven MW622D User Manual
Zanussi Microwave Oven ZM17ML User Manual
Zanussi Range ZCM 600 W User Manual
Zebra Technologies Barcode Reader ZM400 User Manual
Zenoah Brush Cutter BC2602DLM User Manual