POWER AMPLIFIER
Owner’s Manual
Mode d’emploi
Bedienungsanleitung
Manual de instrucciónes
CLIP
A
B
SIGNAL
TEMP
PROTECTION
POWER
ON
OFF
M
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Avoid excessive heat, humidity, dust and vibration.
Keep the unit away from locations where it is likely to be
exposed to high temperatures or humidity — such as
near radiators, stoves, etc. Also avoid locations which
are subject to excessive dust accumulation or vibration
which could cause mechanical damage.
5. Make sure power is off before making or removing
connections.
Always turn the power OFF prior to connecting or
disconnecting cables. This is important to prevent dam-
age to the unit itself as well as other connected equip-
ment.
2. Ventilation
6. Handle cables carefully.
Allow a distance of 10 cm between the unit and the wall
so that heat generated from the unit will be released
effectively. Also, allow enough space between the unit
and other devices. If you mount the unit in an audio rack,
keep a space of 10 cm on the top panel, and a space of
1 cm to the side panel. Remove the rear panel of the rack
or open a vent hole. If heat release is inadequate, the unit
will retain heat inside the unit, which may cause a fire.
Alwaysplugandunplugcables—includingtheACcord
— by gripping the connector, not the cord.
7. Clean with a soft dry cloth.
Never use solvents such as benzine or thinner to clean
the unit. Wipe clean with a soft, dry cloth.
8. Always use the correct power supply.
Makesurethatthepowersupplyvoltagespecifiedonthe
rear panel matches your local AC mains supply. Also
make sure that the AC mains supply can deliver more
thanenoughcurrenttohandleallequipmentusedinyour
system.
3. Avoid physical shocks.
Strong physical shocks to the unit can cause damage.
Handle it with care.
4. Do not open the case or attempt repairs or modifica-
tions yourself.
This product contains no user-serviceable parts. Refer
all maintenance to qualified Yamaha service personnel.
Opening the case and/or tampering with the internal
circuitry will void the warranty.
Contents
Controls and Functions ............................................................. 2
Front Panel........................................................................... 2
Rear Panel ........................................................................... 3
Modes: STEREO/PARALLEL/BRIDGE................................ 4
SPEAKER IMPEDANCE...................................................... 4
Caution for Speaker Connection ............................................... 5
Rack Mounting .......................................................................... 6
Mounting in an EIA standard rack ....................................... 6
Mounting four or fewer amps in an open-backed rack......... 6
Mounting five or more amps, or when (even with four or
fewer units) the back of the rack cannot be left open .......... 6
Portable Rack Mounting ...................................................... 7
Positioning the Housed Amplifier......................................... 7
Specifications ............................................................................ 8
General Specifications......................................................... 8
Block Diagram...................................................................... 9
Dimensions .......................................................................... 9
Performance Graphs.......................................................... 10
Troubleshooting ...................................................................... 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
■ Front Panel
2
3
4
CLIP
A
B
SIGNAL
TEMP
PROTECTION
POWER
ON
OFF
1
5
1 POWER switch and indicator
4 CLIP indicators
This is the main POWER switch. Press to power ON
the amplifier. Press again to power OFF. The POWER
indicator lights up when the amplifier is powered ON.
These red LED indicators light up when the respective
channel’s output signal distortion exceeds 1% (i.e.
clipping). Output signal clipping is usually due to
excessive input signal levels.
2 TEMP indicator
When the temperature of the heat sink exceeds 85
degrees Celsius, this indicator will light red.
5 SIGNAL indicators
These green LED indicators light up when the
respective channel’s output signal exceeds 2 Vrms.
This is equivalent to 1/2 watt into 8Ω, 1 W into 4Ω.
3 PROTECTION indicator
This red LED indicator lights up for approximately 3
seconds when the amplifier is powered ON, indicating
that the soft-start protection system is working. No
sound is output during soft-start up. If one of the
protection systems is activated during normal use, this
indicator lights up and no sound is output. The
speaker system is actually disconnected from the
amplifier outputs when this indicator lights up. The
protection systems are activated when overheating
occurs or a DC voltage is present at the amplifier
outputs. If the problem is corrected, the protection
systems deactivate automatically, this indicator goes
out, and normal amplifier operation is resumed.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Rear Panel
2
3
4
5
INPUT
SPEAKERS
(BRIDGE)
(PARALLEL)
CHANNEL B
CHANNEL A
CHANNEL B
CHANNEL A
BRIDGE
STEREO
G
G
BRIDGE
15
15
20
20
STEREO
PARALLEL
10
10
25
30
40
25
30
40
6
3
6
3
∞
0
∞
0
–dB
–dB
CHANNEL B
CHANNEL A
1
1 Volume controls
4 SPEAKERS terminals
These volume controls allow you to adjust the volume
level in 31 steps in the range between –∞ dB and
0 dB.
For polarity in each mode, refer to the following
diagram.
• STEREO, PARALLEL mode
2 INPUTS (CHANNEL A, B)
SPEAKERS
Two types of balanced inputs for channels A and B
are provided.
Channel A input is used in Bridge and Parallel mode.
CHANNEL B
CHANNEL A
BRIDGE
STEREO
• XLR-3-31 type connectors
Pin 1–ground, pin 2–hot (
+
), and pin 3 cold (-).
Hot
2
Ground
Cold
• BRIDGE mode
1
3
SPEAKERS
CHANNEL B
CHANNEL A
BRIDGE
STEREO
• Barrier strip
Hot (+), Cold (-) and Ground (G).
3 STEREO/BRIDGE/PARALLEL switch
This slide switch is used to set the amplifier operating
mode: STEREO, BRIDGE or PARALLEL.
For details on the functionality of each mode, refer to
“Modes” on page 4.
In BRIDGE mode, the (-) terminals of CHANNELS
A and B are not used.
The minimum impedance for the connected speaker
system is specified in “Speaker Impedance” on
page 4.
5 GND terminals
This is the grounding screw terminal. If hum or noise
occurs, ground (earth) the unit via this jack, or try
connecting it to the chassis of the mixer or preamp,
etc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Modes: STEREO/PARALLEL/BRIDGE
STEREO mode
BRIDGE mode
In this mode, channels A and B operate independently
(as a conventional stereo amp).
In this mode, the CHANNEL A input signal will be
output from the BRIDGE output terminals. In this
The CHANNEL A input signal will be output from
the CHANNEL A output terminals, and the CHAN-
NEL B input signal will be output from the CHAN-
NEL B output terminals.
case, use the front panel (channel)
to adjust the volume.
volume control
A
PARALLEL mode
In this mode, the CHANNEL A input signal will be
output from the output terminals of both channels A
and B. The CHANNEL B input terminals is not used.
B
A
The (channel)
independently.
and
volumes can be adjusted
■ SPEAKER IMPEDANCE
In STEREO and PARALLEL modes, the minimum
load (=speaker) impedance is 4Ω. In BRIDGE mode it
is 8Ω.
Make sure that the impedance does not fall below this
specified impedance.
STEREO mode connections
BRIDGE mode connections
SPEAKERS
SPEAKERS
CHANNEL B
CHANNEL A
BRIDGE
CHANNEL B
CHANNEL A
BRIDGE
STEREO
STEREO
BRIDGE
BRIDGE
Set to STEREO
Set to BRIDGE
STEREO
PARALLEL
MAX. OUTPUT 450W/4Ω (STEREO)
MAX. OUTPUT 900W/8Ω (BRIDGE)
STEREO
PARALLEL
MAX. OUTPUT 450W/4Ω (STEREO)
MAX. OUTPUT 900W/8Ω (BRIDGE)
–
+
–
+
–
+
4Ω min.
Speaker System
4Ω min.
8Ω min.
Speaker System
PARALLEL mode connections
SPEAKERS
CHANNEL B
CHANNEL A
BRIDGE
STEREO
BRIDGE
Set to PARALLEL
STEREO
PARALLEL
MAX. OUTPUT 450W/4Ω (STEREO)
MAX. OUTPUT 900W/8Ω (BRIDGE)
–
+
–
+
4Ω min.
4Ω min.
Speaker System
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution for Speaker Connection
1. Turn off the POWER switch.
• Speaker fuse
The output capacity of your amplifier is very high:
460 W+460 W (8Ω) in stereo and 1240 W (8Ω) in
monaural on the C450; 340 W+340 W (8Ω) in stereo
and 880 W (8Ω) in monaural on the C320; 160
W+160 W (8Ω) in stereo and 400 W (8Ω) in monau-
ral on the C160. Be sure to use a speaker system that
has sufficient input capacity.
2. Remove the cover attachment screw(s) and remove
the protective cover from the speaker terminals.
If the input capacity of your speaker system is lower
than the rated output of the power amplifier, you can
protect your speakers by connecting a fuse serially
between the speaker and amplifier as shown below.
Screw
3. After removing approx. 15 mm of insulation from the
ends of the speaker cables, bind the bare ends of the
speaker wires in the corresponding speaker terminals
and tighten the terminals to securely clamp the wires.
Refer to page 3 for speaker porality.
Speaker system
Power amplifier
_
+
_
+
Fuse
Use the following formula to determine the fuse
capacity according to the speaker’s input capacity.
Po = I2R → I = Po/R
* Shown actual size.
P0 [W] : Speaker’s continuous input capacity (noise
or RMS)
At this time make sure that the bare ends of the
speaker cables do not extend from the terminals in
such a way that they touch the chassis.
R [Ω] : Speaker’s nominal impedance
I [A] : Required fuse capacity
ex.) Speaker’s continuous input capacity : 100 W
Speaker’s impedance : 8Ω
I = 100/8
In this example, the required fuse capacity is calcu-
lated as 3.5 [A].
• Speaker cable
If you use a long speaker cable, use as thick a cable as
possible to prevent deterioration of the damping factor
or power loss inside the cable.
Wire should not
touch the chassis.
4. Reattach the protective cover over the speaker
terminals.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack Mounting
■ Mounting in an EIA standard rack
If multiple high-power amp units are mounted in a rack with poor ventilation, the heat from the amps will cause the
interior of the amp to become very hot, causing the performance of the amps to be impaired. When mounting amps in
a rack, you must make provision for ventilation so that the heat can escape.
When mounting amps in a rack, please attach ventilation panels above and below the amp to allow air circulation.
When doing so, it is necessary for 35% or more of the entire surface area of a 1U size panel to be open.
Air circulation will be even better if the top surface of the rack has ventilation openings.
Ventilation panel
Yamaha provides an optional 1U-size ventilation panel VP1.
480
Unit: mm
■ Mounting four or fewer amps in
■ Mounting five or more amps, or
when (even with four or fewer
units) the back of the rack cannot
be left open
an open-backed rack
Install the ventilation panel above the amps, as shown
in the following figure.
Install ventilation panels above and below each amp,
as shown in the following figure.
Ventilation panel
(attach to the front
or rear of the rack)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Portable Rack Mounting
The amplifier intakes cool air through the front panel and exhausts warm air out the rear panel. When mounting
amplifiers in a portable rack, make sure the rear panel is completely open for ventilation.
(Side View)
(Rear View)
Completely open
Front
INPUT
CHANNEL
SPEAKERS
CHANNEL
(BRIDGE)
(PARALLEL)
CHANNEL
B
A
STEREO
BRIDGE
CHANNEL
B
A
G
G
BRIDGE
Air intake
Air exhaust
20
15
20
15
STEREO
PARALLEL
10
10
25
30
40
25
30
40
6
3
6
3
∞
0
∞
0
–dB
CHANNEL
–dB
CHANNEL
B
A
■ Positioning the Housed Amplifier
Place the case so that the ventilation airflow paths are not blocked.
Front
Less than 10 cm
Front
NO
NO
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
■ General Specifications
C450
C320
C160
Power Output Level (Rated Power)
20 Hz~20 kHz
0.05%
8Ω/STEREO
4Ω/STEREO
8Ω/BRIDGE
460 W + 460 W
620 W + 620 W
1240 W
340 W + 340 W
440 W + 440 W
880 W
160 W + 160 W
200 W + 200 W
400 W
1 kHz
0.05%
8Ω/STEREO
4Ω/STEREO
8Ω/BRIDGE
520 W + 520 W
720 W + 720 W
1440 W
370 W + 370 W
520 W + 520 W
1040 W
175 W + 175 W
230 W + 230 W
460 W
1 kHz, 20 ms, no clip
2Ω/STEREO
1300 W + 1300 W 950 W + 950 W
10 Hz~40 kHz
350 W + 350 W
Power Bandwidth
Half Power, 0.1%
Total Harmonic Distortion (THD + N)
20 Hz~20 kHz, Half Power
4~8Ω/STEREO
8Ω/BRIDGE
0.05%
Frequency Response
10 Hz~50 kHz, +0, –1 dB
0.05%
Intermodulation distortion (IMD)
7 kHz: 60 Hz, 1: 4, Half Power
4~8Ω/STEREO
8Ω/BRIDGE
Damping factor
1 kHz, 8Ω
200
Input Impedance
30 kΩ/Balance, 15 kΩ/Unbalanced
Residual Noise Vol. min.
12.7 kHz LPF
IHF-A network
–75 dB
SN Ratio Input 600Ω shunt
12.7 kHz LPF
IHF-A network
105 dB
104 dB
101 dB
+1.2 dB
Channel Separation
Half Power, 8Ω, Vol. max.
input 600Ω shunt
65 dB, 20 Hz~20 kHz
75 dB, 1 kHz
Slew Rate
8Ω full swing
STEREO
BRIDGE
>30 V/µ sec
>50 V/µ sec
Sensitivity (Vol. max.) Rated Power into 8Ω
+5.7 dB
32.1 dB
+4.2 dB
Voltage Gain (Vol. max.)
Controls
Front Panel
Rear Panel
POWER switch (Push on/Push off)
Volume (31 position dB calibrated)
Mode switch (STEREO/BRIDGE/PARALLEL)
Connectors
Indicators
Input
Barrier strip terminal
XLR-3-31 type
Barrier strip terminal
Output
POWER
TEMP
(heatsink temp ≥ 85°C)
PROTECTION (mute)
CLIP
OUTPUT SIGNAL
× 2
× 2
Protection Circuits
POWER switch ON/OFF, Muting, DC detection
TEMP (heatsink temp ≥ 95°C)
PC limiter
RL ≤ 1Ω
Fan Circuits
Low speed (50°C), Variable, High speed (70°C)
Power Requirements
United States & Canada
Europe
Other
120 V, 60 Hz
230 V, 50 Hz
240 V, 50 Hz
Power Consumption
Dimensions (W × H × D)
Weight
500 W/650 VA
400 W/500 VA
200 W/250 VA
12 kg
480 × 103.5 × 455 mm
16 kg
15 kg
Options
Ventilation panel: VP1
0 dB=0.775 Vrms, Half Power=1/2 Power Output Level (Rated Power)
Specifications subject to change without notice.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Block Diagram
SIGNAL
Ach Power Amp
PC Limiter
CHANNEL A
CHANNEL A
CHANNEL A
(BRIDGE)
(PARALLEL)
G
CLIP
Temperature
Sensor
(Heat Sink)
PROTECTION
TEMP
Protection
Circuit
INPUT
SPEAKERS
CLIP
G
SIGNAL
CHANNEL B
Bch Power Amp
PC Limiter
PARALLEL
BRIDGE
CHANNEL B
STEREO
CHANNEL B
■ Dimensions
424
W:480
308
Unit: mm
9
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Performance Graphs
Mode:STEREO
Both ch Driven
RL=4Ω, f=1kHz
Mode:STEREO
Both ch Driven
RL=4Ω, f=1kHz
C450
C320
5k
5k
1k
1k
100
20
100
20
1
10
100
1k
1
10
100
1k
Output Power [W]
Output Power [W]
Mode:STEREO
Both ch Driven
RL=4Ω, f=1kHz
C160
5k
1k
100
20
1
10
100
1k
Output Power [W]
Troubleshooting
The following table lists the main causes of abnormal operation and the corrective measures required, as well as the
protective circuit operation in each case.
Indicator
Probable Cause
Remedy
Protection Circuit
There is a short at a speaker
terminal, amplifier terminal,
or wire.
Locate and correct the cause
of the short.
The PC limiter circuit
operates to protect the power
transistors.
CLIP indicator lights.
Use a speaker system with
an impedance of at least 4Ω
(stereo) or 8Ω (bridge).
The amplifier load is exces-
sive.
Check the ventilation slots,
and improve the airflow
around the amplifier.
The heat sink temperature
has exceed 85˚C.
Warning by the TEMP
indicator.
TEMP indicator lights.
Check the amplifier ventila-
tion conditions and take
appropriate measures to
improve airflow around the
amplifier.
The thermal protection circuit
operates to protect the power
transistors.
The heat sink temperature
has exceeded 95˚C.
PROTECTION indicator
lights.
A DC voltage of ±2 V or
greater was generated in the
power amplifier’s output
circuit.
Consult your dealer or
nearest Yamaha service
center.
The relay operates to protect
the speaker system.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|