AX-1090
Natural Sound Stereo Integrated Amplifier
Préampli/ampli de puissance stéréo de la série “Natural Sound”
Natural Sound Stereo-Verstärker
Natural Sound Integrerad Stereo Förstärkare
Amplificatore integrato stereo a Suono Naturale
Amplificador integrado estéreo de Sonido Natural
Natural Sound Geïntegreerde Stereo Versterker
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for selecting this YAMAHA stereo amplifier.
FEATURES
CONTENTS
●
145W + 145W (8Ω) RMS Output Power, 0.01% THD,
20–20,000 Hz
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
PURE DIRECT Switch to Reproduce the Purest Source
Sound
SUBSONIC FILTER Switch to Cut Out Undesirable Ultra-
Low-Frequency Signals
PRE OUT/MAIN IN Terminals for Connecting An
Equalizer, Sound Processor, etc.
Supplied Accessories .....................................................2
Connections ...................................................................4
Controls and Their Functions ..........................................6
Operations ......................................................................9
Notes about the Remote Control Transmitter ...............13
Troubleshooting ............................................................14
Specifications ...............................................................15
●
●
●
●
●
●
●
●
Turnover Frequency Switch for Tone Controls
High Quality Component Parts
Remote Control Capability
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
13. Voltage Selector (General Model only)
carefully. Keep it in a safe place for future reference.
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space below.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
Serial No.:
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wire itself.
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly. Therefore, avoid placing objects against
these openings, and install the unit in well-ventilated condition.
Make sure to allow a space of at least 20 cm behind, on the both
sides and above the top panel of the unit. Otherwise it may not
only damage the unit, but also cause fire.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
6. Always set the VOLUME control to “–
” before starting the
∞
audio source play: increase the volume gradually to an
appropriate level after the play has been started.
7. Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10. To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11. Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12. AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
●
●
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
●
If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making
sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
Tape deck 2
Compact disc player
Tuner
Tape deck 1
Speakers A
Right
Left
(General model)
VOLTAGE SELECTOR
2
TUNER
1
CD
3
TAPE
PB
COUPLER
TAPE
1
MAIN
IN
4
AC OUTLETS
REC
OUT
PRE
OUT
3
SPEAKERS
REMOTE
TAPE
PB
CONTROL
TAPE
2
4
GND
REC
OUT
A
B
A
B
3
TAPE
PB
PHONO
TAPE
3
PHONO
4
REC
OUT
AUX
SWITCHED
A
A
OR B:6
B:l2
Ω
Ω
MIN./SPEAKER
MIN./SPEAKER
A
A
OR B:6
B:l2
Ω
Ω
MIN./SPEAKER
MIN./SPEAKER
200W MAX. TOTAL
To AC outlet
Right
Left
Turntable
Video cassette player,
LD player, etc.
Tape deck 3
Speakers B
: Refer to “ABOUT THE OTHER REAR PANEL PARTS” on page 5.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLETS is 200 watts.
AC OUTLETS (3 SWITCHED OUTLETS)
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING SPEAKERS
●
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
Use speakers with the specified impedance shown on the
rear of this unit.
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
●
●
<General model only
>
Banana Plug connections are also possible. Simply insert
the Banana Plug connector into the corresponding terminal.
How to Connect:
Red: positive (+)
Black: negative (–)
Unscrew the knob.
Insert the bare wire.
➀
➁
2
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Tighten the knob and
secure the wire.
1
➂
3
ABOUT THE OTHER REAR PANEL PARTS
REMOTE CONTROL (PHONO) connector
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable provided
with the turntable. This connection allows you to control the
turntable from the provided remote control transmitter.
COUPLER
MAIN
IN
PRE
OUT
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
Notes
●
If you will not use the PRE OUT/MAIN IN terminals, never
remove the jumper pins from these terminals. If removed,
no sound will be output from this unit.
PRE OUT/MAIN IN terminals
●
If you will use this unit with an external unit connected
between the PRE OUT and MAIN IN terminals, make sure
that the PURE DIRECT switch on the front panel is turned
off.
If you will use this unit as a power amplifier, connect the
outputs of an external control amplifier etc. to this unit’s
MAIN IN terminals. In that case, this unit’s controls will not
function except the PHONES jack and the SPEAKERS
switches, so use the controls on the external control
amplifier to make volume adjustment etc.
Removing the jumper pins enables this unit to independently
perform the functions of a control amplifier and a power
amplifier. These terminals are for connection of a signal-
processing system such as a graphic equalizer or sound
processor.
●
If a sound processor or other external unit is connected
between these terminals, the VOLUME control of this unit can
be used for overall adjustment of the level of sound.
To connect such a unit, remove the jumper pins from the PRE
OUT/MAIN IN terminals, connect the inputs of that unit to the
PRE OUT terminals and its outputs to the MAIN IN terminals.
For details, refer to the owner’s manual included with the unit
to be connected.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
1 2
3
4
5
6
VOLUME
l6
NATURAL SOUND STEREO AMPLIFIER AX 1090
INPUT
CD
l8
l4
20
l2
24
l0
TAPE
1
TUNER
PHONO
28
34
8
2
POWER
PURE
TAPE
2
DIRECT
6
4
40
50
60
TAPE
3
3
AUX
l
70
0
–dB
PHONES
SPEAKERS
BASS
DEFEAT
TURNOVER FREQUENCY TREBLE
DEFEAT
SUBSONIC
FILTER
MODE
BALANCE
0
LOUDNESS
FLAT
REC OUT
PHONO
CD
l
l
l
l
l
l
l
TUNER
A
B
1
2/3
–40dB
TAPE COPY
ON
ON
2
2
400Hz
2.5kHz
2
2
ON
MONO
2
2
2
10
PHONO
MC
3
1/2
3
3
3
3
3
3
3
9
AUX
4
4
4
4
4
4
4
8
OFF
OFF
200Hz
5kHz
OFF
STEREO
MM
5
5
5
5
L
5
5
R
5
7
6
7
8
9
0
A B C D
E
F
G
1 POWER switch
5 INPUT selector
Press this switch to switch the power on. Press it again to
switch the power off.
Selects a program source to listen to.
* Standby mode
6 VOLUME control
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit to the standby
mode. (In this mode, the power indicator is half illuminated.)
Used to raise or lower the volume level.
* When the volume is decreased by pressing the MUTING key
on the remote control transmitter, the indicator on the
VOLUME control flashes on and off.
2 Power indicator
Lights up while the power is on.
PHONES
7 PHONES jack
When you listen with headphones,
connect the headphones to the PHONES
jack. When listening with headphones
privately, set both the SPEAKERS A and
B switches to the OFF position.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 PURE DIRECT switch and indicator
Press this switch so that the indicator lights up to listen to an
audio source in the purest sound. (Refer to page 12 for
details.)
8 SPEAKERS switches
Set the switch A or B (or both A and B) for the speaker system
(connected to this unit) you will use to the ON position. Set the
switch for the speaker system you will not use to the OFF
position.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
9 BASS control
Used to increase or decrease the low frequency response. The
DEFEAT position produces flat response.
0 TURNOVER FREQUENCY switches
Used to adjust the turnover point of the BASS and TREBLE
controls respectively. This gives you flexible control over bass
and treble response characteristics.
A TREBLE control
Used to increase or decrease the high frequency response.
The DEFEAT position produces flat response.
B SUBSONIC FILTER switch
Used to cut out undesirable ultra-low-frequency signals caused
by turntable rumble or warped records without losing sound
quality.
C MODE switch
This switch can be used for switching between stereo and
monaural operation. Normally this switch should be set to the
STEREO position.
D BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
E Continuously variable LOUDNESS control
Used to compensate for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
F REC OUT selector
This switch can be used to select a program source and supply
that source directly to the REC OUT terminals on the rear panel,
independently of the setting of the INPUT selector. This function
allows you to record the selected program source while listening
to another program source.
G PHONO (MM/MC) switch
This switch can be used to select either the MM (moving
magnet) or MC (moving coil) position to match the phono
cartridge used. (Refer to page 12 for details.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player, tuner, tape deck and turntable connected to this unit are YAMAHA components designed for remote control compatibility,
then this remote control transmitter will also control various functions of each component.
For Control of This Unit
1 Input selector keys
Selects input source.
2 MUTING key
When pressed, decreases the volume level by 20 dB. To
resume original volume level, press this again.
While muting, the indicator on the VOLUME control flashes on
YAMAHA HIFI SYSTEM
REMOTE CONTROL TRANSMITTER
and off continuously.
TAPE
3
AUX
3 VOLUME +/– keys
PLAY
DIR A
DIR B REC/PAUSE
TAPE
2
1
Turns the volume level up/down.
1
TAPE
A/B
4 POWER key
A/B/C/D/E
TUNER
–
PRESET
+
1
Turns the power on/off.
2
3
PLAY
DISC
CD
*
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit from the
power-on mode to the standby mode, and vice versa. (In
the standby mode, the power indicator on the front panel is
half illuminated.)
PLAY
/CUT
PHONO
4
2
POWER
VOLUME
MUTING
3
4
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 Tape deck keys
Controls tape deck.
DIR A, B and A/B are applicable only to double
cassette tape deck.
*
For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
*
tape running.
2 Tuner keys
Controls tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
3 CD player keys
Controls compact disc player.
DISC is applicable only to compact disc changer.
*
4 Turntable key
Starts/stops record play on turntable.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
VOLUME
INPUT
CD
l6
l8
l4
20
l2
24
l0
TAPE
1
TUNER
PHONO
7
1, 6
28
34
8
2
POWER
PURE
TAPE
2
DIRECT
6
TAPE
3
40
50
60
4
3
AUX
2
70
l
0
–dB
PHONES
SPEAKERS
BASS
DEFEAT
TURNOVER FREQUENCY TREBLE
DEFEAT
SUBSONIC
FILTER
MODE
BALANCE
LOUDNESS
FLAT
REC OUT
PHONO
0
CD
A
B
l
l
l
l
l
l
l
–40dB
10
1
2/3
TUNER
TAPE COPY
ON
ON
2
2
400Hz
2.5kHz
2
2
ON
MONO
2
2
2
PHONO
MC
3
1/2
3
3
3
3
3
3
3
9
8
AUX
4
4
4
4
4
4
4
OFF
OFF
200Hz
5kHz
OFF
STEREO
MM
5
5
5
5
L
5
5
R
5
7
6
7
3
4
TO PLAY A SOURCE
VOLUME
l6
Select the speakers to be used.
1
4
l8
l4
20
24
l2
l0
28
34
8
SPEAKERS
6
4
40
50
3
2
60
70
l
0
–dB
Set to the “ ” position.
∞
If you use two speaker systems, press both the A and B
switches.
*
Turn the power on.
2
3
POWER
Play the source.
5
6
VOLUME
l6
l8
l4
20
l2
24
l0
28
34
8
2
6
Select a desired input source.
4
40
50
60
3
l
70
INPUT
CD
0
–dB
TAPE 1
TUNER
PHONO
TAPE 2
Adjust to the desired output level.
TAPE 3
AUX
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 11–12.)
7
If you select turntable as an input source (PHONO
*
position), you should confirm that the PHONO (MM/MC)
switch is set to the position corresponding to the type of
cartridge being used by the turntable. (Refer to page 12.)
To turn off the power
Press the POWER switch again.
Caution
If you will press the PURE DIRECT switch to turn it on when
the LOUDNESS control is set at a position other than “FLAT”,
be sure to decrease the volume by turning the VOLUME
control counterclockwise before pressing the PURE DIRECT
switch, otherwise the volume may become extremely high
suddenly causing harm to your ears and damage to the
speakers.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VOLUME
3, 5
3
INPUT
CD
l6
l8
l4
20
l2
24
l0
TAPE
1
TUNER
PHONO
28
34
8
2
POWER
PURE
TAPE
2
DIRECT
6
40
50
60
4
TAPE
3
3
AUX
70
l
0
–dB
PHONES
SPEAKERS
BASS
DEFEAT
TURNOVER FREQUENCY TREBLE
DEFEAT
SUBSONIC
FILTER
MODE
BALANCE
LOUDNESS
FLAT
REC OUT
CD
PHONO
0
A
B
l
l
l
l
l
l
l
–40dB
10
1
2/3
TUNER
TAPE COPY
ON
ON
2
2
400Hz
2.5kHz
2
2
ON
MONO
2
2
2
PHONO
MC
3
1/2
3
3
3
3
3
3
3
9
8
AUX
4
4
4
4
4
4
4
OFF
OFF
200Hz
5kHz
OFF
STEREO
MM
5
5
5
5
L
5
5
R
5
7
6
1
TO RECORD A SOURCE TO TAPE (OR DUB
FROM A TAPE TO ANOTHER)
Notes
●
Select the source to be recorded.
If you want to enjoy another source while recording, select it
with the INPUT selector.
The settings of VOLUME, BASS, TREBLE, BALANCE,
LOUDNESS controls and PURE DIRECT switch have no
effect on the material being recorded.
1
REC OUT
●
CD
TUNER
1
2/3
TAPE COPY
PHONO
3
1/2
AUX
REC OUT selector setting on tape dubbing
2
3
Play the source.
To dub from tape deck 1 to
tape deck 2 or 3 (or both
tape deck 2 and 3 at the
same time)
REC OUT
Confirm the source by selecting it with the INPUT
selector and turning up the VOLUME control.
CD
TUNER
1
2/3
TAPE COPY
PHONO
3
1/2
AUX
VOLUME
INPUT
l6
l8
l4
20
l2
CD
24
TAPE 1
l0
TUNER
PHONO
To dub from tape deck 3 to
tape deck 1 or 2 (or both
tape deck 1 and 2 at the
same time)
28
34
8
2
TAPE 2
6
REC OUT
4
40
50
60
TAPE 3
CD
TUNER
1
2/3
TAPE COPY
3
PHONO
3
1/2
AUX
AUX
l
70
0
–dB
* Tape dubbing cannot be done from tape deck 2 to tape deck
1 or 3.
4
5
Set the tape deck to be used for recording in the
recording mode.
To monitor the sound to be recorded (or being
recorded), select the tape deck being used for
recording with the INPUT selector.
INPUT
CD
TAPE 1
TUNER
PHONO
TAPE 2
TAPE 3
AUX
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the BALANCE control
Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
SPEAKERS
BALANCE
0
l
l
2
2
3
3
4
4
R
L 5
5
Adjusting the BASS and TREBLE
controls
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
BASS
TREBLE
1
Set to the “FLAT” position.
LOUDNESS
0 dB
0
BASS
: Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
9
8
7
6
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
2
Set to the loudest listening level that you would listen to.
VOLUME
l6
l8
l4
20
l2
24
l0
28
34
8
TURNOVER FREQUENCY switches
6
4
40
50
60
3
These switches can be used to adjust the turnover point of the
tone controls: either 200 Hz or 400 Hz for BASS and either 2.5
kHz or 5 kHz for TREBLE. This gives you flexible control over
bass and treble response characteristics.
2
l
70
0
–dB
3
Turn until the desired volume is achieved.
TURNOVER FREQUENCY
LOUDNESS
0 dB
0
400Hz
200Hz
2.5kHz
5kHz
9
8
7
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PURE DIRECT switch
PHONO (MM/MC) switch
You can enjoy the purest possible sound from your audio
sources by setting this switch so that the indicator lights up. By
doing so, the audio signals bypass the BASS, TREBLE,
BALANCE, LOUDNESS controls, SUBSONIC FILTER switch,
MODE switch and the PRE OUT/MAIN IN terminals, thus
eliminating any alterations to the audio signals.
Select either MM or MC position depending on your PHONO
cartridge, Moving Magnet or Moving Coil type. However, if you
use a high output MC cartridge, select MM position.
To select the MC position, press this switch so that it is held
inward. To select the MM position, press this switch so that it is
released outward.
PURE
PHONO
MC
DIRECT
MM
Setting the SUBSONIC FILTER switch
Setting the MODE switch
If you set this switch to “ON” position, undesirable ultra-low-
frequency signals caused by turntable rumble or warped
records can be cut out without losing sound quality.
This switch can be used for switching between stereo and
monaural operation. Normally this switch should be set to the
STEREO position.
MODE
SUBSONIC
FILTER
MONO
ON
STEREO
OFF
Open/close the control door
When it is not necessary to operate controls inside the control
door, close the door.
To close the door
To open the door
12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
2
Remote control
sensor
1
3
Within approximately
6 m (19.7 feet)
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
Notes
●
●
Use only AA, R6, UM-3 batteries for replacement.
There should be no large obstacles between the remote
control transmitter and the main unit.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
●
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The unit fails to turn on when the POWER
switch is pressed.
Power cord is not plugged in or is not
completely inserted.
Firmly plug in the power cord.
No sound.
Incorrect output cord connections.
Connect the cords properly. If the problem
persists, the cords may be defective.
Appropriate input source is not selected.
Select an appropriate input source with the
INPUT selector.
The SPEAKERS switches are not set
properly.
Set the SPEAKERS switch which
corresponds to the speakers to be used to
the ON position.
Speaker connections are not secure.
Secure the connections.
The sound suddenly goes off.
The protection circuit has functioned because
of short circuit etc.
Turning the unit off and then on will reset the
protection circuit.
Only one side speaker outputs the sound.
Incorrect setting of the BALANCE control.
Incorrect cord connections.
Adjust it to the appropriate position.
Connect the cords properly. If the problem
persists, the cords may be defective.
There is a lack of bass, and no ambience.
Sound “hums”.
The + and – wires are connected in reverse
at the amplifier or speakers.
Connect the speaker wires in the correct
phase (+ and –).
Incorrect cord connections.
Firmly connect the audio plugs. If the
problem persists, the cords may be
defective.
No connection from the turntable to the GND
terminal.
Make the GND connection between the
turntable and this unit.
Sound level is low or sound is distorted
while playing a record on the turntable.
The LOUDNESS control is functioning.
Set the LOUDNESS control to the FLAT
position.
The PHONO (MM/MC) switch is set to the
improper position.
Set the PHONO (MM/MC) switch to the
proper position.
The MUTING key is ON.
First, turn the volume control to the full left.
Then, turn the MUTING key OFF with the
remote control transmitter and adjust the
volume.
Using the BASS, TREBLE, BALANCE,
LOUDNESS controls, SUBSONIC FILTER
switch and MODE switch does not affect
the tone.
The PURE DIRECT switch is ON.
The PURE DIRECT switch must be switched
OFF to use those controls.
The volume level cannot be increased, or
sound is distorted.
The power to the component connected to
the REC OUT terminals of this unit is off.
Turn the power to the component on.
Turn the power to this unit on.
The sound is degraded when listening
with the headphones connected to the
compact disc player or cassette deck that
are connected with this unit.
The power to this unit is off.
The remote control transmitter does not
work.
Direct sunlight or lighting (of an inverter type
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
Change position of the main unit.
The distance or range within which the
remote control transmitter can be used
decreases.
The batteries of this remote control
transmitter are too weak.
Replace the batteries with new ones.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.01% THD
..........................................145W+145W
6 ohms, 20 Hz to 20 kHz, 0.02% THD
..........................................185W+185W
Headphone Jack Rated Output/ Impedance
Output Level
(8 ohms, 1 kHz, 0.015% THD).....1.05V
Impedance.............................220 ohms
Tone Control Characteristics
BASS:
Boost/cut.....................±10 dB (20 Hz)
Turnover Frequency ........200, 400 Hz
TREBLE:
Frequency Response (20 Hz to 20 kHz)
CD/TUNER/TAPE/AUX ............0±0.5 dB
MAIN IN...................................0±0.5 dB
Boost/cut...................±10 dB (20 kHz)
Turnover Frequency............2.5, 5 kHz
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring
method)
Filter Characteristics
8/6/4/2 ohms.........220/290/360/460W
RIAA Equalization Deviation
(20 Hz to 20 kHz)
SUBSONIC FILTER
..................................15 Hz, –18 dB/oct
DIN Standard Output Power per Channel
[Europe model only]
(4 ohms, 1 kHz, 0.7% THD).........250W
PHONO MM ...........................±0.3 dB
PHONO MC............................±0.5 dB
Continuous Loudness Control
(Level related equalization)
Total Harmonic Distortion
(20 Hz to 20 kHz)
Attenuation ....................–40 dB (1 kHz)
Dynamic Headroom
[General model only]
8/6 ohms......................1.81 dB/1.95 dB
PHONO MM to REC OUT
(3V) .........................................0.003%
PHONO MC to REC OUT
Audio Muting ................................–20 dB
Gain Tracking Error (0 to –60 dB)....2 dB
IEC Power (8 ohms, 1 kHz, 0.01% THD)
[Europe model only]
.....................................................170W
(3V) .........................................0.007%
CD/TUNER/TAPE/AUX to PRE OUT
(1V) .........................................0.004%
CD/TUNER/TAPE/AUX to SP OUT
(72.5W/8 ohms) ......................0.007%
MAIN IN to SP OUT
Power Supply
[Europe model] ..............AC 230V, 50 Hz
[General model]
Power Band Width
8 ohms, 72.5W, 0.03% THD
.....................................10 Hz to 50 kHz
...........AC 110/120/220/240V, 50/60 Hz
(72.5W/8 ohms) ......................0.005%
Power Consumption.......................370W
Damping Factor
8 ohms, 20 Hz to 20 kHz
...........................................350 or more
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted)
.................................................... 92 dB
PHONO MC (500 µV Input Shorted)
.................................................... 75 dB
CD (Input Shorted)
(PURE DIRECT; ON)...............110 dB
TUNER/TAPE/AUX (Input Shorted)
(PURE DIRECT; ON)...............106 dB
AC Outlets
3 SWITCHED OUTLETS
....................................200W max. total
Input Sensitivity/Impedance
Dimensions (W x H x D)
..............................435 x 171 x 448 mm
(17-1/8” x 6-3/4” x 17-5/8”)
PHONO MM.............2.5 mV/47 k-ohms
PHONO MC ..............160 µV/220 ohms
CD/TUNER/TAPE/AUX
................................150 mV/47 k-ohms
MAIN IN........................1.0V/47 k-ohms
Weight...................18.3 kg (40 lbs. 4 oz.)
Residual Noise (IHF-A Network)
CD (PURE DIRECT; ON).............40 µV
TUNER/TAPE/AUX
Accessories...Remote control transmitter
Batteries
Maximum Input Signal
(1 kHz, 0.01% THD)
PHONO MM............................170 mV
PHONO MC...........................13.5 mV
(PURE DIRECT; ON)...................80 µV
Specifications subject to change without
notice.
Channel Separation (Vol. –30 dB)
PHONO MM/MC (Input Shorted
Output Level/Impedance
REC OUT...............150 mV/2.2 k-ohms
PRE OUT ....................1.0V/1.8 k-ohms
1 kHz/10 kHz)....................70 dB/55 dB
CD/TUNER/TAPE/AUX (Input 5.1 k-ohms
Terminated 1 kHz/10 kHz)
Maximum Voltage Output
...........................................65 dB/50 dB
20 Hz to 20 kHz, 0.02% THD.........6.5V
15
Download from Www.Somanuals.com. All Manuals Search And Download.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B.
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VU 60520
Download from Www.Somanuals.com. All Manuals Search And Download.
|