AX-570/470
Natural Sound Stereo Integrated Amplifier
100W + 100W (8Ω) RMS Output Power, 0.015% THD, 20–20,000 Hz <AX-570>
65W + 65W (8Ω) RMS Output Power, 0.015% THD, 20–20,000 Hz <AX-470>
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
PURE DIRECT Switch to Reproduce the Purest Source Sound
SUBSONIC FILTER Switch to Cut Out Undesirable
Ultra-Low-Frequency Signals <For AX-570 only>
PRE OUT/MAIN IN Terminals Useful for Connecting An Equalizer,
Sound Processor, etc. <For AX-570 only>
Remote Control Capability
Thank you for selecting this YAMAHA stereo integrated amplifier.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
OWNER’S MANUAL
IMPORTANT!
Please record the serial number of this
CONTENTS
unit in the space below.
Explanation of Graphical Symbols
•
Model:
Serial No.:
Safety Instructions ................... 2
Supplied Accessories .............. 3
Connections ............................. 4
Operations ............................... 6
Remote Control Transmitter ... 10
Notes about the Remote
Control Transmitter ................. 11
Troubleshooting ...................... 12
Specifications ......................... 13
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without
affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable
until it is too late, YAMAHA and the Electronic
Industries Association’s Consumer Electronics
Group recommend you to avoid prolonged
exposure from excessive volume levels.
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
●
●
Remote Control
Batteries (size AA, R6, UM-3)
Transmitter
PLAY/CUT
PLAY
PHONO
CD
POWER
SKIP
SEARCH
PRESET
PAUSE/STOP DISC SKIP
A/B/C/D/E TUNER
–
+
DIR
A
DECK A/B
PLAY
DIR
B
TAPE
TAPE
1
2
REC/PAUSE
EQ
STOP
REC MUTE
ON/FLAT
–
PRESET SKIP
AUX
+
VOLUME
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
●
●
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
Turntable
Tuner
Compact disc player
Speakers A
Left
Right
REMOTE
CONTROL
(U.S.A. model)
To AC outlet
Right
Left
Video cassette player,
LD player, etc.
Tape deck 1
Tape deck 2
Speakers B
Illustration: AX-570
Parts in shaded area (
) are not present on AX-470.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING SPEAKERS
●
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
Use speakers with the specified impedance shown on the
rear of this unit.
Banana Plug connections are also possible (except for
Scandinavian models). Simply insert the Banana Plug
connector into the corresponding terminal.
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
●
●
How to Connect:
Red: positive (+)
Black: negative (–)
Unscrew the knob.
Insert the bare wire.
[Remove approx. 5mm
➀
➁
2
(1/4”) insulation from
1
the speaker wires.]
Tighten the knob and
➂
secure the wire.
3
ABOUT THE ACCESSORY TERMINALS
AC OUTLETS (SWITCHED)
PRE OUT/MAIN IN terminals
<Except Australia, U.K. and Europe models of
<For AX-570 only>
AX-470>
Removing the jumper pins enables this unit to independently
perform the functions of a control amplifier and a power
amplifier. These terminals are for connection of a signal-
processing system such as a graphic equalizer or sound
processor.
If a sound processor or other component is connected, the
VOLUME control of this unit can be used for overall
adjustment of the level of sound. To connect such a unit,
remove the jumper pins from the PRE OUT/MAIN IN
terminals, connect the inputs of that unit to the PRE OUT
terminals and its outputs to the MAIN IN terminals. For details,
refer to the owner’s manual included with the unit to be
connected.
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLETS is 100 watts.
REMOTE CONTROL (PHONO) connector
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable
provided with the turntable. This connection allows you to
control the turntable from the provided remote control
transmitter.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
4
3
7
<AX-570>
2
1, 6
PHONO
PHONES
<AX-470>
7
3
7
4
2
1, 6
PHONES
7
TO PLAY A SOURCE
Select the speakers to be used.
1
4
<AX-570>
<AX-470>
SPEAKERS
SPEAKERS
Set to the “ ” position.
∞
If you use two speaker systems, press both the A and B
switches.
*
<AX-570>
<AX-470>
2
3
POWER
/STANDBY
POWER
Play the source.
5
6
Select a desired input source.
Adjust to the desired output level.
<For AX-570 only>
*
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 8–9.)
7
If you select turntable as an input source (PHONO
position), refer to “Setting the PHONO switch” on page 9.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3, 5
<AX-570>
3
3
1
3, 5
<AX-470>
1
TO RECORD A SOURCE TO TAPE (OR DUB FROM A TAPE TO ANOTHER)
Select the source to be recorded.
1
4
5
Set the tape deck in the recording mode.
REC OUT
To monitor the sound being recorded, select the tape
deck being used for recording with the INPUT selecto.
CD
TAPE
1
TUNER
TAPE
2
PHONO
AUX
2
3
Play the source.
Confirm the source by selecting it with the INPUT
selector and turning up the VOLUME control.
Notes
●
If you want to enjoy another source while recording, select it
with the INPUT selector.
●
VOLUME, BASS, TREBLE, BALANCE, LOUDNESS
controls and PURE DIRECT switch settings have no effect
on the material being recorded.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the BALANCE control
Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
<AX-470>
<AX-570>
BALANCE
SPEAKERS
0
l
l
SPEAKERS
2
2
3
3
4
4
R
L 5
5
Adjusting the BASS and TREBLE
controls
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
BASS
TREBLE
0
0
l
l
l
l
2
2
2
2
3
3
3
3
4
4
4
4
1
5
5
5
5
LOUDNESS
FLAT
l
30dB
2
l0
3
Set to the “FLAT” position.
9
BASS
: Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
4
8
5
7
6
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
2
3
Set to the loudest listening level that
you would listen to.
LOUDNESS
FLAT
l
30dB
2
l0
Turn so that the desired volume can
be achieved.
3
9
4
8
5
7
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PHONO switch
For AX-570 only
Using the PURE DIRECT switch
<
>
You can enjoy the purest possible sound from your audio
sources by setting this switch so that the indicator illuminates.
By doing so, the audio signal bypasses the BASS, TREBLE,
BALANCE and LOUDNESS controls, eliminating any
alterations to the audio signal.
Select either MM or MC position depending on your PHONO
cartridge, Moving Magnet or Moving Coil type. However, if you
use a high output MC cartridge, select MM position.
Concerning AX-570 only, the SUBSONIC FILTER switch
and the PRE OUT/MAIN IN terminals are also bypassed.
*
PHONO
MC
PURE
DIRECT
MM
Setting the SUBSONIC FILTER switch
For AX-570 only
<
>
If you set this switch to “ON” position, undesirable ultra-low-
frequency signals caused by turntable rumble or warped
records can be cut out without losing sound quality.
SUBSONIC
FILTER
ON
OFF
When you listen with headphones
PHONES
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player, tuner, turntable, equalizer, and tape deck connected to this unit are YAMAHA components, then this remote control
transmitter will also control various functions of each component.
KEY FUNCTIONS
For Control of This Unit
PLAY/CUT
PLAY
PHONO
CD
POWER
Turns the power on/off.
SKIP
SEARCH
PRESET
PAUSE/STOP DISC SKIP
A/B/C/D/E TUNER
–
+
Selects input source.
DIR A
DECK A/B
PLAY
DIR B
TAPE
TAPE
1
2
REC/PAUSE
EQ
STOP
REC MUTE
ON/FLAT
–
PRESET SKIP
AUX
+
Turns the volume level up/down.
VOLUME
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the
same. On each key function, refer to the corresponding instruction on your component’s manual.
Controls tuner
+: Selects higher preset station
number.
Starts/stops record play on turntable.
–: Selects lower preset station
number.
A/B/C/D/E: Selects the page (A – E)
of preset station buttons.
Controls compact disc player.
* DISC SKIP is applicable only to
compact disc changer.
PLAY/CUT
PLAY
PHONO
CD
POWER
SKIP
SEARCH
PRESET
PAUSE/STOP DISC SKIP
A/B/C/D/E TUNER
–
+
Controls tape deck.
DIR A
DECK A/B
PLAY
DIR B
TAPE
TAPE
1
2
* DIR A, B and DECK A/B are
applicable only to double cassette
tape deck.
Controls equalizer.
* PRESET SKIP selects any preset
equalizer curve whenever this is
pressed. (After the last preset
curve is selected, it returns to the
first one by another press on this
key.)
* For a single cassette deck with
automatic reverse function,
pressing DIR A will reverse the
direction of tape running.
REC/PAUSE
EQ
STOP
REC MUTE
ON/FLAT
–
PRESET SKIP
AUX
+
VOLUME
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY mode
<For AX-470 and Europe model of AX-570>
<AX-470>
While the power is on, pressing the POWER key on the remote
control transmitter switches the unit to the STANDBY mode.
(In this mode, the indicator is half illuminated.)
Note
The POWER switch on the front panel of this unit should
be turned off when left unused for a long period of time.
POWER on mode
STANDBY mode
<Europe model of AX-570>
POWER on mode
STANDBY mode
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
1
3
2
Remote control
sensor
Within approximately
7 m (23 feet)
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will
●
Notes
●
not be used for an extended period of time.
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The unit fails to turn on when the POWER
switch is pressed.
Power cord is not plugged in or is not
completely inserted.
Firmly plug in the power cord.
No sound.
Incorrect output cord connections.
Appropriate input source is not selected.
Speaker connections are not secure.
Connect the cords properly. If the problem
persists, the cords may be defective.
Select an appropriate input source with the
INPUT selector.
Secure the connections.
The sound suddenly goes off.
The protection circuit has activated because
of short circuit etc.
Turning the unit off and then on will reset the
protection circuit.
Only one side speaker outputs the sound.
Incorrect setting of the BALANCE control.
Incorrect cord connections.
Adjust it to the appropriate position.
Connect the cords properly. If the problem
persists, the cords may be defective.
There is a lack of bass, and no ambience.
Sound “hums”.
The + and – wires are connected in reverse
at the amplifier or speakers.
Connect the speaker wires in the correct
phase (+ and –).
Incorrect cord connections.
Firmly connect the audio plugs. If the
problem persists, the cords may be defective.
No connection from the turntable to the GND
terminal.
Make the GND connection between the
turntable and this unit.
Sound level is low.
The LOUDNESS control is functioning.
Set the LOUDNESS control to the FLAT
position.
Using the BASS, TREBLE, BALANCE,
LOUDNESS controls and SUBSONIC
FILTER switch (AX-570 only) does not
affect the tone.
The PURE DIRECT switch is ON.
The PURE DIRECT switch must be switched
OFF to use those controls.
The remote control transmitter does not
work.
Direct sunlight or lighting (of an inverter type
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
Change position of the main unit.
The distance or range within which the
remote control transmitter can be used
decreases.
The batteries of this remote control
transmitter are too weak.
Replace the batteries with new ones.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Minimum RMS Output Power per Channel
(PURE DIRECT; ON)
<AX-570>
8 ohms, 20 Hz to 20 kHz, 0.015% THD
...............................................100W+100W
6 ohms, 20 Hz to 20 kHz, 0.03% THD
[Except Scandinavia model]
...............................................120W+120W
<AX-470>
Maximum Input Signal (1 kHz, 0.01% THD)
<AX-570>
Channel Separation (Vol. –30 dB)
<AX-570>
PHONO MM ...................................150 mV
PHONO MC......................................10 mV
<AX-470>
PHONO MM/MC (Input Shorted
1 kHz/10 kHz) .........................75 dB/60 dB
CD/TUNER/TAPE/AUX (Input 5.1 k-ohms
Terminated 1 kHz/10 kHz) ......65 dB/50 dB
<AX-470>
PHONO MM ...................................115 mV
Output Level/Impedance
<AX-570>
CD/TUNER/TAPE/AUX (Input 5.1 k-ohms
Terminated 1 kHz/10 kHz) ......65 dB/50 dB
8 ohms, 20 Hz to 20 kHz, 0.015% THD
[Except Europe model] ..............65W+65W
[Europe model] ..........................75W+75W
6 ohms, 20 Hz to 20 kHz, 0.03% THD
[U.S.A. and Canada model].......75W+75W
[Australia, U.K. and General model]
...................................................70W+70W
[Europe (except Scandinavia) model]
...................................................80W+80W
REC OUT ......................150 mV/220 ohms
PRE OUT............................1.0V/470 ohms
<AX-470>
Tone Control Characteristics
BASS: Boost/cut................±10 dB (20 Hz)
TREBLE: Boost/cut...........±10 dB (20 kHz)
REC OUT .........................150 mV/1 k-ohm
Headphone Jack Rated Output/ Impedance
<AX-570>
Output Level (8 ohms, 1 kHz, 0.015% THD)
..........................................................0.47V
Impedance ..................................470 ohms
<AX-470>
Filter Characteristics <AX-570 only>
SUBSONIC FILTER .........15 Hz, –18 dB/oct
Continuous Loudness Control
Attenuation............................–30 dB (1 kHz)
(Level related equalization)
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring
method)
Output Level (8 ohms, 1 kHz, 0.019% THD)
..........................................................0.46V
Impedance ..................................390 ohms
Gain Tracking Error (0 to –60 dB)
<AX-570>..............................................2 dB
<AX-470>..............................................3 dB
<AX-570>
8/6/4/2 ohms.................140/170/220/290W
<AX-470>
Frequency Response (20 Hz to 20 kHz)
CD/TUNER/TAPE/AUX....................0±0.5 dB
MAIN IN <AX-570 only>.................0±0.5 dB
[Except Europe model]
Power Supply
8/6/4/2 ohms...................95/115/135/160W
[Europe model]
8/6/4/2 ohms.................115/135/160/180W
[U.S.A. and Canada models]
..........................................AC 120V, 60 Hz
[Australia and U.K. models]
..........................................AC 240V, 50 Hz
[Europe model]..................AC 230V, 50 Hz
[General model]
RIAA Equalization Deviation (20 Hz to 20 kHz)
PHONO MM......................................±0.3 dB
PHONO MC <AX-570 only>............±0.5 dB
DIN Standard Output Power per Channel
(4 ohms, 1 kHz, 0.7% THD)
[Europe model only]
<AX-570>.........................................150W
<AX-470>.........................................110W
Total Harmonic Distortion (20 Hz to 20 kHz)
<AX-570>
................AC 110/120/220/240V, 50/60 Hz
PHONO MM to REC OUT (3V) ......0.003%
PHONO MC to REC OUT (3V).......0.007%
CD/TUNER/TAPE/AUX to PRE OUT (1V)
........................................................0.005%
CD/TUNER/TAPE/AUX to SP OUT
(50W/8 ohms).................................0.008%
<AX-470>
Power Consumption
<AX-570>
IEC Power (8 ohms, 1 kHz, 0.015% THD)
[Europe model only]
[U.S.A. model] ...................................200W
[Canada model] ...................330 VA, 260W
[Australia and U.K. models]...............210W
[Scandinavia model]..........................180W
[Europe (except Scandinavia) and General
models]..............................................210W
<AX-470>
<AX-570>.........................................110W
<AX-470>...........................................85W
Power Band Width
<AX-570>
PHONO MM to REC OUT (3V) ......0.003%
CD/TUNER/TAPE/AUX to SP OUT
(35W/8 ohms).................................0.008%
8 ohms, 50W, 0.03% THD
..........................................10 Hz to 50 kHz
<AX-470>
[U.S.A. model] ...................................160W
[Canada model] ...................280 VA, 220W
[Australia and U.K. models]...............170W
[Scandinavia model]..........................160W
[Europe (except Scandinavia) model]
..........................................................190W
[General model].................................170W
Intermodulation Distortion
(Rated output/8 ohms) ........................0.01%
8 ohms, 35W, 0.03% THD
..........................................10 Hz to 50 kHz
Signal-to-Noise Ratio (IHF-A Network)
<AX-570>
Damping Factor
8 ohms, 20 Hz–20 kHz
PHONO MM (5 mV Input Shorted)
......................................................... 92 dB
PHONO MC (0.5 mV Input Shorted)
......................................................... 76 dB
CD/TUNER/TAPE/AUX (Input Shorted)
....................................................... 110 dB
<AX-470>
<AX-570> ............................................320
<AX-470> ............................................240
AC Outlets
[Except Australia, U.K. and Europe models
of AX-470]
Damping Factor (DIN)
4 ohms, 40 Hz
[Australia, U.K. and Europe models]
<AX-570> ............................................160
<AX-470> ............................................120
SWITCHED OUTLETS
..........................................100W max. total
PHONO MM (5 mV Input Shorted)
......................................................... 88 dB
CD/TUNER/TAPE/AUX (Input Shorted)
(PURE DIRECT; ON) ..................... 110 dB
Dimensions (W x H x D)
...................................435 x 150 x 388.5 mm
(17-1/8” x 5-7/8” x 15-5/16”)
Input Sensitivity/Impedance
PHONO MM.....................2.5 mV/47 k-ohms
PHONO MC <AX-570 only>
..........................................160 µV/220 ohms
CD/TUNER/TAPE/AUX
Weight
Residual Noise (IHF-A Network)
(PURE DIRECT; ON)...........................70 µV
<AX-570> .....................11 kg (24 lbs. 3 oz.)
<AX-470> ..................9.5 kg (20 lbs. 14 oz.)
........................................150 mV/47 k-ohms
MAIN IN <AX-570 only>
.............................................1.0V/10 k-ohms
Accessories...........Remote control transmitter
Batteries
Specifications subject to change without
notice.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B.
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Download from Www.Somanuals.com. All Manuals Search And Download.
|